Oak - Scene7

Dimensions

Width - 80cm

Depth - 33cm

Height - 86cm

Venetia - Shoe StorageAssembly Instructions - Please keep for future reference

Issue 8 - 06/10/14

ALR2595

Issue 2 - 02/06/11 - Tools and Rule added to fittings page.

906/5716

Issue 3 - 17/05/12 - Argos code added.

Issue 4 - 20/12/12 - Title changed to Venetia.Rebates taken off of the Left Side, Right Side, Top and Base - all gone up to issue B.Shelves increased in size to 760 x 312mm - gone up to issue B.

MADE IN BRITAIN

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928or email: [email protected] (quoting your original order number)

Important - Please read these instructions fully before starting assembly

Issue 5 - 29/07/13 - Click have agreed with Argos to put their help line number on the Venetia range as a trial.

Issue 6 - 06/02/14 - Replaced the F284 screw (6x5/8 flange head) with a F79 screw (6x1/2 flange head).

Issue 7 - 25/07/14 - Deleted the blow up diagram at steps 4b and 5b and updated the text to current.

Issue 8 - 06/10/14 - The unit is now available in Oak or White with a different handle on each.The handle screw has been changed to a Flange Blunt End.

Oak

White

323/9603

White

Safety and Care AdviceImportant - Please read these instructions fully before starting assembly

• Warning: This unit weighs approximately 28kgs.Please lift with care.

• Check you have all thecomponents and tools listed on pages1, 2 and 3.

• Remove all fittings from the plastic bags and separate them into their groups.

• Keep children and animals away from the work area, small parts could choke if swallowed.

• Parts of the assembly will be easier with 2 people.

• Make sure you have enough space to layout the parts before starting.

• Do not stand or put weight on the product, this could cause damage.

• Assemble the item as close to its final position (in the same room) as possible.

• Assemble on a soft level surface to avoid damaging the unit or your floor (use opened out unit carton).

1

Care and maintenance

• Only clean using a damp cloth and mild detergent, do no use bleach or abrasive cleaners.

• From time to time check that there are no loose screws on this unit.

• This product should not be discarded with household waste. Take to your localauthority waste disposal centre.

Note: If required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

• We do notrecommend the use of power drill/drivers for inserting screws,

as this could damage the unit.Only use hand screwdrivers.

• Safety note: It isrecommended that this unit is secured to a wall using the bracket supplied.

• Dispose of all packaging carefully and responsibly.

Tools required

Rule

Scissors HammerEye protection (when using a hammer or drill)

Cross-head screwdriver

Electric drill(only use when drilling walls and doors)Square

mm10

2030

4050

6070

8090

100

mm10

2030

4050

6070

8090

100

2

1

80%x 2

5

2

7 8

7 8

6

10

9

Back (X803)(848 x 780mm)

Drawer Wrap (W429)(1393 x 95mm)

Drawer Base (T429)(319 x 740mm) 11

3

4Left Side (D0844B)(830 x 312mm)

Right Side (D0845B)(830 x 312mm) Base (D0847B)

(797 x 329mm)

Top (D0846B)(797 x 329mm)

Loose Shelf (D0850B)(760 x 312mm) x 3

Components - PanelsPlease check you have all the panels listed below

If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: [email protected] (quoting your original order number and the reference numbers below)

Oak Drawer Front (D0848A)(786 x 138mm)

White Drawer Front (D3060A)(786 x 138mm)

6

Oak Left Door (D3058A)(683 x 392mm)

Oak Right Door (D3059A)(683 x 392mm)

White Left Door (D3061A)(683 x 392mm)

White Right Door (D3062A)(683 x 392mm)

OR

OR

3

A B

D

C

Large locking nut (F900) x 4

F

G H

Small locking nut (F3) x 2

P

J

I

9mm Screw (F74) x 2

LK

9mm Screw (F73) x 4

Drawer runner (F1004) x 2

Q

Metal dowel (F901) x 6

Nail (F51) x 22

E

40mm Screw (F910) x 4 25mm Screw (F95) x 6

13mm Screw (F63) x 8

Plastic Nail (F91) x 4 Shelf support (F121) x 12

M ON

Bracket (F327) x 1

Handle (F236) x 3

Hinge plate (F523) x 4 Hinge (F518) x 4

Ruler - Use this ruler to help correctly identify the screws

mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

Please check you have all the fittings listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Components - FittingsIf you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: [email protected] (quoting your original order number and the reference numbers below)

13mm Screw (F79) x 1

Handle (F315) x 3OAK UNIT WHITE UNIT

OR

4

Step 1

6

9

BA

C

a:

A

b:C

9

a:

b:

A

A

FC

C

Prepare the drawer front and wrap

a: Screw 2 metal dowels . into the holes shown on the back of the drawer front .

Note: Tighten the metal dowels up fully against the panel.

b: Insert 2 small locking nuts into the holes shown on the drawer wrap .

Note: The arrow on the locking nut must point towards the hole in the edge of the panel.

A

6

C

9

Assemble the drawer

a: Place the drawer base into the narrow slot on the drawer wrap . . Fold the wrap around the base.

b: Turn the drawer wrap assembly over and push it onto the back of the drawer front .

Note: Turn the locking nuts clockwise to secure panels - more than 1/2 a turn.

10

9

6

C

Step 2

9

9

10plain surface

9

6

6

Note: Due to the manufacturing process, the holes for the locking nut can be on either surface of the drawer wrap.

Note: The locking nuts can be on either surface of the drawer sides.Make sure that the small groove is on the inside, as shown.

Assembly InstructionsIf you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: [email protected] (quoting your original order number and the reference numbers below)

Finished front edge

Finished front edge

Finished front edge

Assembly Instructions

5

Step 3

Step 4

FF

Q

Attach the handle

Attach a handle to the drawer front using 2 screws .

Q

F6

6

J

P

B

B

J

Fit runners to left side

a: Place a runner on the left side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the left side .

c: Insert 2 large lockingnuts into the left side . .


Fit 2 hinge plates onto the left side , making sure that the slot is facing towards the finished front edge.

1P

J

J

B

N

1

N

N

1

1

1N

1

1

Finishedfront edge

J

P

b:

c:

a:

B

1

This shows the handle for the Oak unit.You may have the White unit.


6

Step 5

Fini

shed

front

edg

e

J

P

JP

J

Finished front edge

b:

c:

a:

B

B

Fit runners to right side

a: Place a runner on the right side . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw .

b: Slide the runner back the other way and fit the 2nd screw into the corresponding hole in the right side .

c: Insert 2 large lockingnuts into the right side .


Fit 2 hinge plates onto the right side , making sure that the slot is facing towards the

2P

J

J

B

N

2

2

N

N2

N

2

2

2

Finished front edge

Finished front edge

2

Finished front edge

Finished front edge


7

Step 6

Prepare the top

Note: The top and base panels are very similar but, the holes in the top panel are not drilled all the way through.

Fix a bracket to the middle of the top , flush to the back edge, using screw .

Screw 4 metal dowels into the holes shown on the top .

A

A

A

A

Finished front edge

M

3M3

3

G

A

Join the top and right side

Push the top onto the right side . Use a screwdriver to tighten the 2 large locking nuts fitted to the right side .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

B

A2

3

Step 7

32

32

B

B

2

G

M

Finished front edge

Finished front edge


8

Step 8

3

Fit the left side

Push the left side onto the top . Use a screwdriver to tighten the 2 large locking nuts fitted to the left side .

Note: Turn the large locking nuts as far as they will go - more than 1/2 a turn.

13

B1

B 1

Fit the base

Attach the base to the left side and right side using 4 screws . .

E

E

E

E

Step 9

41

2E

4 1

2

y


9

Step 10

Fit the plastic nails

Tap the plastic nails into the base as shown.

The plastic nails must go up into the bottom edge of the left side and right side .

K

K

4

12

2

Step 11

Fit the back

a: Square up the unit by making sure that measurement x to x equals y to y.

b: Place the back onto the unit.

Nail around the outside edges of the back .

Note: Nails should be spaced about 150mm apart.

Stand the unit up for the next step.

y y

x

xD

10

The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Ya:

b:

10

D

10

K

K

K

K

4 1


10

Step 12

Step 13

Make sure that the plastic sleeve is fully pushed onto the shelf stud.

Fit the shelf studs

For each of the 3shelves , insert 4 shelf studs at the required height.

L

L

L

L

L

L

L

L

L

L

L

L

5L

M

Secure unit to a wall

To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the metal bracket fitted under the top of the unit.

Fixings are not supplied as they will need to suit the wall type, and the length of screw will depend on the distance of the back of the unit to the wall.

Warning: Take care when

drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert.

3

L

WALL

WALL

Top of unit

M

3M


11

Step 14

Step 15

Fit the shelves

Lower the 3 shelves down onto the shelf studs .

5

L

Fit the drawer

Slide both the runners forward and locate the sides of the drawer wrap . between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners .

Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner .

Note: Do not overtighten the screws .If they catch on the runner you may need to loosen them slightly.

P

92nd threaded

hole

P

I

9

9

9

I

I

I

I

P

P

P

55

5

This shows the Oak unit.You may have the White unit.


12

Step 16

Prepare the doors

Push fit 2 hinges into each door and .

Secure each hinge with2 screws .

Note: Before securing with the screws, make sure that the hinges are positioned at 90 degrees with the edge of the door.

H

O7 8 7

90

O

O

HH

O

HH

x 2

8

90

O

O

HH

O

HH

x 2

Note: The right door has a shallow identification hole between the 2 handle holes.

8

Q


13

Step 17

F

F

Q

8

Fit doors and handles

Note: The easiest way to attach each door and . is to fit the top hinge first, then align and fit the other hinges.

a: Push the hinge onto the front part of the hinge plate .The recess at the bottom of screw B goes into the slot in the hinge plate.

b: Keep the hinge FLAT against the hinge plate as you slide it across as far as it will go.Tighten screw A.

c: The hinge must be flat against the hinge plate prior to anyadjustment.

d: The hinge must NOT be AT AN ANGLE to the hinge plate when assembled.This would indicate that the recess at the bottom of screw B had not located in the slot in the hinge plate and the hinge would not be secure.Remove the hinge from the hinge plate and then re-assemble being careful to followinstructions a-c.

e: Attach a handle to each door and using 2 screws .

O

O

O

N

N

N

O

N

Q

F

78

7 8

e:

a: b:

c: d:

N

O

N

N

B

N

O

O

O

A

O

N

B

7

Q

White

F

F

This shows the handles for the Oak unit. You may have the White unit.

Q

8

7

Note: The right door has a shallow identification hole between the 2 handle holes.

8

Assembly InstructionsStep 18

14

b:

c:

d:

a:Adjust the doors if needed

a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back andside-to-side in the 3 positions shown.Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown.

b: Height adjustment.Loosen screws A on hinge plates and move door up or down as required.Retighten screw A.

c: Forward and Back adjustment.Loosen screw B on hinge plate and move door in or out as required.Retighten screw B.

d: Sidewaysadjustment.To move door ‘out’ loosen screw C.To move door ‘in’ tighten screw C.

A

A

B

C


15 ALR2595

Step 19

Assembly is complete

If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928or email: [email protected] (quoting your original order number and the reference numbers on the component pages)Argos Ltd, 489-499 Avebury Boulevard, Central Milton Keynes, MK9 2NW

Oak

White

Oak - Scene7

Documents

Transcript of Oak - Scene7