NTC Thermistors - produktinfo.conrad.com · NTC Thermistors !Note • Please read rating and...
Transcript of NTC Thermistors - produktinfo.conrad.com · NTC Thermistors !Note • Please read rating and...
Cat.No.R44E-13
NTC Thermistors
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
EU RoHS Compliant • All the products in this catalog comply with EU RoHS. • EU RoHS is "the European Directive 2002/95/EC on the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment." • For more details, please refer to our website 'Murata's Approach for EU RoHS'
(http://www.murata.com/info/rohs.html).
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
1
2
3
4
5
6
7
8
Part Numbering 2
Basic Characteristics 6
Temperature Sensor and Compensation 0201 (0603) Size 7
Temperature Sensor and Compensation 0402 (1005) Size 8
Temperature Sensor and Compensation 0603 (1608) Size 10
Temperature Sensor and Compensation 0805 (2012) Size 12
Temp. Sensor and Compensation Chip Type Standard Land Pattern Dimensions 13
Temp. Sensor and Compensation Chip Type Temperature Characteristics (Center Value) 14
Temp. Sensor and Compensation Chip Type !Caution/Notice 18
Temp. Sensor and Compensation Chip Type Package 22
Temperature Sensor Thermo String Type 25
Temperature Sensor Thermo String Type Specifications and Test Methods 26
Temperature Sensor Lead Type 28
Temperature Sensor Lead Insulation Type 29
Temperature Sensor Temperature Characteristics (Center Value) 31
Temperature Sensor Thermo String Type/Lead Type !Caution/Notice 32
Temperature Sensor Thermo String Type/Lead Type Package 34
Inrush Current Suppression Lead Type 35
Current - R Ratio (RT/R25)/Current - Temperature Characteristics (Typical) 37
Inrush Current Suppression Lead Type !Caution/Notice 41
Inrush Current Suppression Lead Type Package 43
1
2
3
4
5
6
7
8
CONTENTS
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
o Part Numbering
qProduct ID
wSeries
yResistance Tolerance
uIndividual Specifications
NTC Thermistors for Temp. Sensor and Compensation Chip Type
NC NTC Thermistors Chip Type
D
E
F
J
P
±0.5%
±3%
±1%
±5%
Product ID
Code
Code
Series
Resistance Tolerance
(Part Number)
tResistance
Expressed by three-digit alphanumerics. The unit is ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures.
Structures and others are expressed by two figures.
102
103
104
Ex.
1kΩ
10kΩ
100kΩ
Code Resistance
iPackaging
RA
RB
RC
RL
Plastic Taping 4mm Pitch
Paper Taping 4mm Pitch
Paper Taping 2mm Pitch (10000 pcs.)
Paper Taping 2mm Pitch (15000 pcs.)
Code Packaging
Plated Termination Series
eDimensions (LgW)
03
15
18
21
Code Dimensions (LgW)
0.60g0.30mm
1.00g0.50mm
1.60g0.80mm
2.00g1.25mm
EIA
0201
0402
0603
0805
rTemperature Characteristics
WB
WD
WF
WL
WM
XC
XF
XH
XM
XQ
XV
XW
Code Temperature Characteristics
Nominal B-Constant 4050e4099K
Nominal B-Constant 4150e4199K
Nominal B-Constant 4250e4299K
Nominal B-Constant 4450e4499K
Nominal B-Constant 4500e4549K
Nominal B-Constant 3100e3149K
Nominal B-Constant 3250e3299K
Nominal B-Constant 3350e3399K
Nominal B-Constant 3500e3549K
Nominal B-Constant 3650e3699K
Nominal B-Constant 3900e3949K
Nominal B-Constant 3950e3999K
y
J
e
18
w
P
r
XH
t
103
u
03
i
RBNC
q
03
Individual SpecificationsCodeEx.
Standard Type
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
qProduct ID
wIndividual Specifications
uLead Wire Type
iShape of the Lead Wire Kink
NTC Thermistor for Temperature Sensor Thermo String Type
NXF NTC Thermistors Sensor Thermo String Type A ø0.3 Copper Lead Wire with Polyurethane Coat
1
2
Shape of the Lead Wire Kink
Product ID Code Lead Wire Type
Code
(Part Number)
tResistance
Expressed by three figures. The unit is (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures.
103
473
104
Ex.
10kΩ
47kΩ
100kΩ
Code Resistance
The Twist of Lead Wire Type
Standard Type
T Commercial Type
Code
yResistance Tolerance
F ±1%
Code Resistance Tolerance
oPackaging
B Bulk
Code Packaging
!0Dimensions (Full Length)
025
030
040
050
060
070
080
090
100
110
120
130
140
150
25mm
30mm
40mm
50mm
60mm
70mm
80mm
90mm
100mm
110mm
120mm
130mm
140mm
150mm
Code Dimensions (Full Length)
Individual Specifications
rTemperature Characteristics
WB
WF
XH
Nominal B-Constant 4050–4099K
Nominal B-Constant 4250–4299K
Nominal B-Constant 3350–3399K
Code Temperature Characteristics
eChip Dimensions
15 1.00 x 0.50mm
Code Dimensions (LxT)
0402
EIA
t
103
w
T
e
15
r
XH
y
F
u
A
i
2
o
B
!0
025NXF
q
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
qProduct ID
wSeries
tResistance Tolerance
yIndividual Specifications
NTC Thermistors for Temperature Sensor Lead Type
NT NTC Thermistors E
F
±3%
±1%
E1
N6
PB
Individual Specifications
Product ID Code Resistance Tolerance
Code
(Part Number)
rResistance
Expressed by three-digit alphanumerics. The unit is ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures.
A lead structure and other specifications are expressed by two-digit alphanumerics.
202
203
Ex.
2kΩ
20kΩ
Code Resistance
Standard Bulk (NTSA, NTSD0 Series)
Standard Ammo Pack Taping (NTSA Series)
Standard Bulk (NTSD1 Series)
SA0
SD0
SD1
for Temperature Sensors No Lead-coating Type
for Temperature Sensors Lead-coating Type(Total Length 30mm max.)
for Temperature Sensors Lead-coating Type(Total Length 30 to 50mm)
Code
uPackaging (NTSA/NTSD0 Series)
A0
B0
Ammo Pack Taping
Bulk
Code Packaging
uTotal Length (NTSD1 Series)
30
40
50
30mm
40mm
50mm
Code Total Length
Series
eTemperature Characteristics
WB
WC
WD
WF
XH
XM
XR
XV
Nominal B-Constant 4050e4099K
Nominal B-Constant 4100e4149K
Nominal B-Constant 4150e4199K
Nominal B-Constant 4250e4299K
Nominal B-Constant 3350e3399K
Nominal B-Constant 3500e3549K
Nominal B-Constant 3700e3749K
Nominal B-Constant 3900e3949K
Code Temperature Characteristics
t
F
w
SA0
e
XH
r
103
y
E1
u
B0NT
q
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
y
B0
e
160
r
L
t
BMNT
q w
PA7
qProduct ID
wSeries
rResistance Tolerance
tIndividual Specifications
NTC Thermistors for Inrush Current Suppression Lead Type
NT NTC Thermistors L
PA7
PA9
PAA
PAD
PAJ
PAN
±15%
DK
Individual Specifications
Product ID
Code
Code
Series
Resistance Tolerance
Code
(Part Number)
eResistance
Expressed by three-digit alphanumerics. The unit is ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures. If there is a decimal point, it is expressed by the capital letter "R." In this case, all figures are significant digits.
A lead structure and other specifications are expressed by two-digit alphanumerics.
3R0
100
Ex.
3Ω
10Ω
Code Resistance
Standard (Bulk)
yPackaging
A0
B0
Ammo Pack Taping
Bulk
Code Packaging
Body Diameter
ø18mm, ø22mm
DN Standard (Bulk) ø10mm, ø13mm
BM Standard Type (Bulk) ø7mm, ø9mm
B1 Standard Type (Ammo Pack) ø7mm, ø9mm
D6 Standard Type (Ammo Pack) ø10mm, ø13mm
Inrush CurrentSuppressionLead Type
ø7mm
ø9mm
ø10mm
ø13mm
ø18mm
ø22mm
Nominal Body Diameter
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
6
1. Zero-power Resistance of Thermistor: R
2. B-Constant
R=R0 expB (1/T-1/T0) ..............(1)R: Resistance in ambient temperature T (K)(K: absolute temperature)R0: Resistance in ambient temperature T0 (K)B: B-Constant of Thermistor
as (1) formulaB=Rn (R/R0) / (1/T-1/T0) ............(2)
3. Thermal Dissipation Constant
When electric power P (mW) is spent in ambient temperature T1 and thermistor temperature rises T2, there is a formula as followsP=C (T2-T1) ..................(3)C: Thermal dissipation constant (mW/°C)Thermal dissipation constant is varied with dimensions, measurement conditions, etc.
4. Thermal Time Constant
Period in which Thermistor's temperature will change 63.2% of its temperature difference from ambient temperature T0 (°C) to T1 (°C).
Resistance vs. Temperature
!Basic Characteristics
!Performance
Thermal Time Constant
Item
Resistance
Condition
Measured by zero-power in specified ambient temperature.
Rated Electric PowerShows the required electric power that causes Thermistor's temperature to rise to a specified temperature by self heating, at ambient temperature of 25 °C.
Permissive Operating Current It is possible to keep Thermistor's temperature rising max. 1˚C.
Thermal DissipationConstant
Shows necessary electric power that Thermistor's temperature rises 1˚C by self heating.It is calculated by next formula (mW/˚C).
B-Constant
Calculated between two specified ambient temperatures by next formula.T and T0 is absolute temperature (K).
Rn (R/R0)B =
1/TY1/T0
PC =
TYT0
102
101
Res
ista
nce
vs. T
empe
ratu
re C
hara
cter
istic
s, R
/R25
−20Temperature (˚C)
0 20 40 60 80 12010010−2
10−1
1
B=3450B=3900B=4100
Basic Characteristics
T1
T0
Time
63.2%
X
Tem
pera
ture
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please inquire about test conditions and ratings.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
7
1
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor and Compensation 0201 (0603) Size
0201/0402/0603/0805 sized Chip NTC Thermistors have a unique inner construction and nickel barrier terminations which provide excellent solderability and high stability in the application environment.
Features1. Excellent solderability and high stability in environment2. Excellent long-term aging stability3. High accuracy in resistance and B-Constant4. Reflow soldering possible5. NCP series are recognized by UL/cUL (UL1434, File No. E137188).
Applications1. Temperature compensation for transistor, IC and crystal oscillator in mobile communications2. Temperature sensor for rechargeable batteries3. Temperature compensation of LCD4. Temperature compensation in general use of electric circuits
Electrode(Ag System + Ni Plating + Sn Plating)
0.15±0.05 0.15±0.050.60±0.03
(in mm)
0.30
±0.0
30.
30±0
.03
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
NCP03YS110J05RL 11 ±5% 2750 ±3% 2758 2758 2758 9.50 100 1
NCP03YS220J05RL 22 ±5% 2750 ±3% 2758 2758 2758 6.70 100 1
NCP03YS330J05RL 33 ±5% 2750 ±3% 2758 2758 2758 5.50 100 1
NCP03YS470J05RL 47 ±5% 2750 ±3% 2758 2758 2758 4.60 100 1
NCP03YS680J05RL 68 ±5% 2750 ±3% 2758 2758 2758 3.80 100 1
NCP03YS101J05RL 100 ±5% 2750 ±3% 2758 2758 2758 3.10 100 1
NCP03XM102p05RL 1.0k 3500 ±1% 3539 3545 3560 1.00 100 1
NCP03XM152p05RL 1.5k 3500 ±1% 3539 3545 3560 0.81 100 1
NCP03XM222p05RL 2.2k 3500 ±1% 3539 3545 3560 0.67 100 1
NCP03XM332p05RL 3.3k 3500 ±1% 3539 3545 3560 0.55 100 1
NCP03XM472p05RL 4.7k 3500 ±1% 3539 3545 3560 0.46 100 1
NCP03XH682p05RL 6.8k 3380 ±1% 3428 3434 3455 0.38 100 1
NCP03XH103F25RL 10k ±1% 3380 ±0.8% 3428 3434 3455 0.31 100 1
NCP03XH103F05RL 10k ±1% 3380 ±1% 3428 3434 3455 0.31 100 1
NCP03XH103p05RL 10k 3380 ±1% 3428 3434 3455 0.31 100 1
NCP03XV103p05RL 10k 3900 ±1% 3930 3934 3944 0.31 100 1
NCP03XH153p05RL 15k 3380 ±1% 3428 3434 3455 0.25 100 1
NCP03XH223p05RL 22k 3380 ±1% 3428 3434 3455 0.21 100 1
NCP03WF333p05RL 33k 4250 ±1% 4303 4311 4334 0.17 100 1
NCP03WB473p05RL 47k 4050 ±3% 4101 4108 4131 0.14 100 1
NCP03WL473p05RL 47k 4485 ±1% 4537 4543 4557 0.14 100 1
NCP03WF683p05RL 68k 4250 ±1% 4303 4311 4334 0.12 100 1
NCP03WL683p05RL 68k 4485 ±1% 4537 4543 4557 0.12 100 1
NCP03WF104F05RL 100k ±1% 4250 ±1% 4303 4311 4334 0.10 100 1
NCP03WF104p05RL 100k 4250 ±1% 4303 4311 4334 0.10 100 1
NCP03WL104p05RL 100k 4485 ±1% 4537 4543 4557 0.10 100 1
NCP03WL154p05RL 150k 4485 ±1% 4537 4543 4557 0.08 100 1
NCP03WL224p05RL 220k 4485 ±1% 4537 4543 4557 0.06 100 1
p is filled with resistance tolerance codes (E: ±3%, J: ±5%).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 125°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
8
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor and Compensation 0402 (1005) Size
0201/0402/0603/0805 sized Chip NTC Thermistors have a unique inner construction and nickel barrier terminations which provide excellent solderability and high stability in the application environment.
Features1. Excellent solderability and high stability in environment2. Excellent long-term aging stability3. High accuracy in resistance and B-Constant4. Reflow soldering possible5. Provide flexibility to use the smaller size version in certain circuits because of same B-Constant in the same resistance.6. NCP series are recognized by UL/cUL (UL1434, File No. E137188).
Applications1. Temperature compensation for transistor, IC and crystal oscillator in mobile communications2. Temperature sensor for rechargeable batteries3. Temperature compensation of LCD4. Temperature compensation in general use of electric circuits
Electrode(Ag System + Ni Plating + Sn Plating)
0.25±0.10 0.25±0.101.0±0.05
(in mm)
0.5±
0.05
0.5±
0.05
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
NCP15XC220p03RC 22 3100 ±3% 3126 3128 3136 6.70 100 1
NCP15XC330p03RC 33 3100 ±3% 3126 3128 3136 5.50 100 1
NCP15XC470p03RC 47 3100 ±3% 3126 3128 3136 4.60 100 1
NCP15XC680p03RC 68 3100 ±3% 3126 3128 3136 3.80 100 1
NCP15XF101p03RC 100 3250 ±3% 3282 3284 3296 3.10 100 1
NCP15XF151p03RC 150 3250 ±3% 3282 3284 3296 2.50 100 1
NCP15XM221p03RC 220 3500 ±3% 3539 3545 3560 2.10 100 1
NCP15XM331p03RC 330 3500 ±3% 3539 3545 3560 1.70 100 1
NCP15XQ471p03RC 470 3650 ±2% 3688 3693 3706 1.40 100 1
NCP15XQ681p03RC 680 3650 ±3% 3688 3693 3706 1.20 100 1
NCP15XQ102p03RC 1.0k 3650 ±2% 3688 3693 3706 1.00 100 1
NCP15XW152p03RC 1.5k 3950 ±3% 3982 3987 3998 0.81 100 1
NCP15XW222p03RC 2.2k 3950 ±3% 3982 3987 3998 0.67 100 1
NCP15XW332p03RC 3.3k 3950 ±3% 3982 3987 3998 0.55 100 1
NCP15XM472p03RC 4.7k 3500 ±2% 3539 3545 3560 0.46 100 1
NCP15XW472p03RC 4.7k 3950 ±3% 3982 3987 3998 0.46 100 1
NCP15XW682p03RC 6.8k 3950 ±3% 3982 3987 3998 0.38 100 1
NCP15XH103D03RC 10k ±0.5% 3380 ±0.7% 3428 3434 3455 0.31 100 1
NCP15XH103F03RC 10k ±1% 3380 ±1% 3428 3434 3455 0.31 100 1
NCP15XH103p03RC 10k 3380 ±1% 3428 3434 3455 0.31 100 1
NCP15XV103p03RC 10k 3900 ±3% 3930 3934 3944 0.31 100 1
NCP15XW153p03RC 15k 3950 ±3% 3982 3987 3998 0.25 100 1
NCP15XW223p03RC 22k 3950 ±3% 3982 3987 3998 0.21 100 1
NCP15WL223p03RC 22k 4485 ±1% 4537 4543 4557 0.21 100 1
NCP15WB333p03RC 33k 4050 ±3% 4101 4108 4131 0.17 100 1
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
9
2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Continued from the preceding page.
NCP15WL333p03RC 33k 4485 ±1% 4537 4543 4557 0.17 100 1
NCP15WB473D03RC 47k ±0.5% 4050 ±0.5% 4101 4108 4131 0.14 100 1
NCP15WB473F03RC 47k ±1% 4050 ±1% 4101 4108 4131 0.14 100 1
NCP15WB473p03RC 47k 4050 ±1% 4101 4108 4131 0.14 100 1
NCP15WL473p03RC 47k 4485 ±1% 4537 4543 4557 0.14 100 1
NCP15WD683p03RC 68k 4150 ±3% 4201 4209 4232 0.12 100 1
NCP15WL683p03RC 68k 4485 ±1% 4537 4543 4557 0.12 100 1
NCP15WF104D03RC 100k ±0.5% 4250 ±0.5% 4303 4311 4334 0.10 100 1
NCP15WF104F03RC 100k ±1% 4250 ±1% 4303 4311 4334 0.10 100 1
NCP15WF104p03RC 100k 4250 ±1% 4303 4311 4334 0.10 100 1
NCP15WL104p03RC 100k 4485 ±1% 4537 4543 4557 0.10 100 1
NCP15WL154p03RC 150k 4485 ±1% 4537 4543 4557 0.08 100 1
NCP15WM154p03RC 150k 4500 ±3% 4571 4582 4614 0.08 100 1
NCP15WM224p03RC 220k 4500 ±3% 4571 4582 4614 0.06 100 1
NCP15WM474p03RC 470k 4500 ±3% 4571 4582 4614 0.04 100 1
p is filled with resistance tolerance codes (E: ±3%, J: ±5%).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 125°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
10
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor and Compensation 0603 (1608) Size
0201/0402/0603/0805 sized Chip NTC Thermistors have a unique inner construction and nickel barrier terminations which provide excellent solderability and high stability in the application environment.
Features1. Excellent solderability and high stability in environment2. Excellent long-term aging stability3. High accuracy in resistance and B-constant4. Flow / Reflow soldering possible5. Provide flexibility to use the smaller size version in certain circuits because of same B-Constant in the same resistance.6. NCP series are recognized by UL/cUL (UL1434, File No. E137188).
Applications1. Temperature compensation for transistor, IC and crystal oscillator in mobile communications2. Temperature sensor for rechargeable batteries3. Temperature compensation of LCD4. Temperature compensation in general use of electric circuits
Electrode(Ag System + Ni Plating + Sn Plating)
0.2-0.6 0.2-0.61.6±0.15
(in mm)
0.8±
0.15
0.8±
0.15
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
NCP18XF101p03RB 100 3250 ±3% 3282 3284 3296 3.10 100 1
NCP18XF151p03RB 150 3250 ±3% 3282 3284 3296 2.50 100 1
NCP18XM221p03RB 220 3500 ±3% 3539 3545 3560 2.10 100 1
NCP18XM331p03RB 330 3500 ±3% 3539 3545 3560 1.70 100 1
NCP18XQ471p03RB 470 3650 ±2% 3688 3693 3706 1.40 100 1
NCP18XQ681p03RB 680 3650 ±3% 3688 3693 3706 1.20 100 1
NCP18XQ102p03RB 1.0k 3650 ±2% 3688 3693 3706 1.00 100 1
NCP18XW152p03RB 1.5k 3950 ±3% 3982 3987 3998 0.81 100 1
NCP18XW222p03RB 2.2k 3950 ±3% 3982 3987 3998 0.67 100 1
NCP18XW332p03RB 3.3k 3950 ±3% 3982 3987 3998 0.55 100 1
NCP18XM472p03RB 4.7k 3500 ±2% 3539 3545 3560 0.46 100 1
NCP18XW472p03RB 4.7k 3950 ±3% 3982 3987 3998 0.46 100 1
NCP18XW682p03RB 6.8k 3950 ±3% 3982 3987 3998 0.38 100 1
NCP18XH103D03RB 10k ±0.5% 3380 ±0.7% 3428 3434 3455 0.31 100 1
NCP18XH103F03RB 10k ±1% 3380 ±1% 3428 3434 3455 0.31 100 1
NCP18XH103p03RB 10k 3380 ±1% 3428 3434 3455 0.31 100 1
NCP18XV103p03RB 10k 3900 ±3% 3930 3934 3944 0.31 100 1
NCP18XW153p03RB 15k 3950 ±3% 3982 3987 3998 0.25 100 1
NCP18XW223p03RB 22k 3950 ±3% 3982 3987 3998 0.21 100 1
NCP18WB333p03RB 33k 4050 ±3% 4101 4108 4131 0.17 100 1
NCP18WB473D03RB 47k ±0.5% 4030 ±0.5% 4101 4108 4131 0.14 100 1
NCP18WB473F10RB 47k ±1% 4050 ±1.5% 4101 4108 4131 0.14 100 1
NCP18WB473p03RB 47k 4050 ±2% 4101 4108 4131 0.14 100 1
NCP18WD683p03RB 68k 4150 ±3% 4201 4209 4232 0.12 100 1
NCP18WF104D03RB 100k ±0.5% 4200 ±0.5% 4255 4260 4282 0.10 100 1
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
11
3
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Continued from the preceding page.
NCP18WF104F12RB 100k ±1% 4200 ±1% 4255 4260 4282 0.10 100 1
NCP18WF104p03RB 100k 4250 ±2% 4303 4311 4334 0.10 100 1
NCP18WM154p03RB 150k 4500 ±3% 4571 4582 4614 0.08 100 1
NCP18WM224p03RB 220k 4500 ±3% 4571 4582 4614 0.06 100 1
NCP18WM474p03RB 470k 4500 ±3% 4571 4582 4614 0.04 100 1
p is filled with resistance tolerance codes (E: ±3%, J: ±5%).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 125°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
12
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor and Compensation 0805 (2012) Size
0201/0402/0603/0805 sized Chip NTC Thermistors have a unique inner construction and nickel barrier terminations which provide excellent solderability and high stability in the application environment.
Features1. Excellent solderability and high stability in environment2. Excellent long-term aging stability3. High accuracy in resistance and B-constant4. Flow / Reflow soldering possible5. Provide flexibility to use the smaller size version in certain circuits because of same B-Constant in the same resistance.6. NCP series are recognized by UL/cUL (UL1434, File No. E137188).
Applications1. Temperature compensation for transistor, IC and crystal oscillator in mobile communications2. Temperature sensor for rechargeable batteries3. Temperature compensation of LCD4. Temperature compensation in general use of electric circuits
2.0±0.2
0.2-0.7 0.2-0.7
Electrode(Ag System + Ni Plating + Sn Plating)
1.25
±0.2
0.85
±0.1
5
(in mm)
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
NCP21XM221J03RA 220 ±5% 3500 ±3% 3539 3545 3560 3.00 200 2
NCP21XQ471J03RA 470 ±5% 3650 ±3% 3688 3693 3706 2.00 200 2
NCP21XQ102J03RA 1.0k ±5% 3650 ±3% 3688 3693 3706 1.40 200 2
NCP21XW222J03RA 2.2k ±5% 3950 ±3% 3982 3987 3998 0.90 200 2
NCP21XM472J03RA 4.7k ±5% 3500 ±3% 3539 3545 3560 0.65 200 2
NCP21XV103J03RA 10k ±5% 3900 ±3% 3930 3934 3944 0.44 200 2
NCP21XW153J03RA 15k ±5% 3950 ±3% 3982 3987 3998 0.36 200 2
NCP21XW223J03RA 22k ±5% 3950 ±3% 3982 3987 3998 0.30 200 2
NCP21WB333J03RA 33k ±5% 4050 ±3% 4101 4108 4131 0.24 200 2
NCP21WB473J03RA 47k ±5% 4050 ±3% 4101 4108 4131 0.20 200 2
NCP21WF104J03RA 100k ±5% 4250 ±3% 4303 4311 4334 0.14 200 2
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 125°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Temp. Sensor and Compensation Chip Type Standard Land Pattern Dimensions
13
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Chip LandSolder Resist
b a
c
Part Number SolderingMethods Chip (LxW)
Dimensions (mm)a b c
NCP03NCP15
NCP18
NCP21
Reflow SolderingReflow SolderingFlow Soldering
Reflow SolderingFlow Soldering
Reflow Soldering
0.6x0.31.0x0.5
1.6x0.8
2.0x1.25
0.250.4
0.6-1.00.6-0.81.0-1.11.0-1.1
0.250.4-0.50.8-0.90.6-0.70.9-1.00.6-0.7
0.30.5
0.6-0.80.6-0.81.0-1.21.0-1.2
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
127.366101.66281.72666.14853.94644.27336.49430.26225.22621.15017.82815.10312.85911.0009.4528.1627.0776.1615.3894.7314.1683.6873.2732.9152.6052.3352.1001.8941.7131.5541.4121.2871.1761.077
NCPppYS110
Resistance (Ω)Temp. (°C)B-ConstantResistance
Part Number
254.732203.325163.452132.296107.89388.54672.98760.52350.45142.30035.65730.20525.71922.00018.90416.32314.15512.32310.7789.4618.3367.3746.5455.8305.2104.6714.2013.7893.4273.1072.8252.5742.3522.153
NCPppYS220
Resistance (Ω)355.823273.975213.003166.943131.997105.31884.67068.62855.98145.85937.81931.39626.21122.00018.56015.73513.40311.4629.8428.4887.3486.3995.5954.8964.2993.7953.3602.9832.6562.3672.1161.9011.7121.543
NCPppXC220
Resistance (Ω)382.098304.987245.178198.444161.839132.819109.48190.78575.67763.44953.48545.30838.57833.00028.35624.48521.23218.48416.16714.19212.50411.0619.8178.7447.8147.0066.3015.6835.1404.6614.2373.8623.5283.230
NCPppYS330
Resistance (Ω)533.734410.962319.504250.415197.996157.978127.005102.94283.97268.78956.72847.09439.31733.00027.84023.60320.10417.19314.76312.73211.0229.5988.3927.3456.4485.6925.0404.4743.9833.5513.1732.8512.5682.314
NCPppXC330
Resistance (Ω)544.201434.376349.193282.633230.498189.167155.927129.299107.78290.36776.17664.52954.94447.00040.38634.87230.23926.32623.02520.21317.80915.75313.98212.45411.1309.9798.9748.0947.3206.6386.0355.5005.0244.600
NCPppYS470
Resistance (Ω)760.166585.310455.051356.652281.994224.998180.886146.614119.59697.97280.79467.07355.99747.00039.65133.61628.63324.48721.02618.13315.69813.67011.95210.4619.1848.1077.1796.3735.6735.0574.5204.0603.6573.296
NCPppXC470
Resistance (Ω)787.354628.459505.215408.915333.487273.688225.597187.071155.940130.744110.21293.36179.49468.00058.43050.45443.75038.08933.31329.24425.76622.79220.23018.01916.10214.43712.98411.71010.5919.6048.7317.9577.2696.655
NCPppYS680
Resistance (Ω)
1
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
1157.874924.204742.963601.346490.422402.482331.760275.105229.324192.270162.076137.296116.902100.00085.92774.19764.33956.01348.98943.00637.89133.51729.75026.49823.68021.23119.09417.22115.57514.12412.84011.70210.6909.787
NCPppYS101
Resistance (Ω)1824.1751390.6851070.653831.138650.960514.441409.700328.877265.759215.785176.395145.161120.152100.00083.66970.36159.45650.47043.02936.83031.64927.36423.75620.65118.01115.80013.90812.26310.8449.6228.5637.6486.8506.162
NCPppXF101
Resistance (Ω)2736.2622086.0281605.9791246.708976.440771.661614.550493.315398.639323.677264.592217.742180.228150.000125.503105.54189.18475.70564.54355.24647.47341.04535.63430.97627.01623.70020.86218.39416.26514.43412.84411.47210.2759.243
NCPppXF151
Resistance (Ω)4947.9043703.7552798.8732135.8871645.0371278.0341000.620789.612627.752502.474405.010328.480268.044220.000181.576150.668125.681105.33688.71775.05963.77754.41546.63140.11534.63730.01326.11022.79019.95717.54115.45313.66312.11410.778
NCPppXM221
Resistance (Ω)7421.8565555.6324198.3093203.8312467.5551917.0511500.9301184.418941.628753.711607.514492.720402.066330.000272.365226.002188.521158.004133.076112.58895.66681.62269.94660.17251.95545.01939.16534.18629.93526.31223.18020.49418.17116.168
NCPppXM331
Resistance (Ω)11822.4738767.7456570.2244971.7843796.9332923.4002269.5991775.2251399.0501110.220887.257713.463577.375470.000384.800316.757262.177218.069182.297153.150129.249109.55193.28179.75068.44658.99651.03644.33238.64033.79029.66426.12323.09120.472
NCPppXQ471
Resistance (Ω)17104.85412685.2489505.8557193.2195493.4364229.5993283.6752568.4112024.1581606.2751283.6911032.245835.351680.000556.733458.287379.320315.504263.749221.579186.998158.499134.960115.38399.02985.35673.83964.14055.90548.88842.91837.79533.40929.618
NCPppXQ681
Resistance (Ω)
Continued on the following page.
1099.815846.832658.372516.007407.991325.529261.707212.123173.033141.747116.89497.04281.01668.00057.36848.63641.42635.42830.42126.23522.71219.77817.29315.13413.28811.72910.3869.2208.2087.3176.5395.8745.2914.768
NCPppXC680
Resistance (Ω)
2750K 2750K 3100K 2750K 3100K 2750K 3100K 2750K
2750K 3250K 3250K 3500K 3500K 3650K 3650K3100K
11Ω 22Ω 22Ω 33Ω 33Ω 47Ω 47Ω 68Ω
100Ω 100Ω 150Ω 220Ω 330Ω 470Ω 680Ω68Ω
Temp. (°C)B-ConstantResistance
Part Number
Detailed Resistance - Temperature Tables are downloadable from the following URL.
http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en
14
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Temp. Sensor and Compensation Chip Type Temperature Characteristics (Center Value)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
2
Continued from the preceding page.
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
75.96154.52039.60729.10321.60116.19812.2649.3707.2195.6094.3913.4632.7512.2001.7711.4341.1690.9580.7890.6540.5450.4560.3830.3240.2750.2340.2000.1720.1490.1290.1120.0980.0850.075
NCPppXW222
Resistance (kΩ)113.94181.77959.41143.65432.40124.29718.39614.05510.8298.4146.5865.1954.1263.3002.6562.1521.7531.4371.1840.9810.8170.6840.5750.4860.4120.3510.3010.2580.2230.1930.1680.1460.1280.113
NCPppXW332
NCPppXM472
Resistance (kΩ)
105.70579.12659.79445.63035.14427.30321.37716.86913.41110.7358.6537.0185.7264.7003.8793.2192.6852.2501.8951.6041.3631.1630.9960.8570.7400.6410.5580.4870.4260.3750.3300.2920.2590.230
Resistance (kΩ)133.043100.75677.07659.54046.40136.48228.90423.04718.50914.97412.1899.9788.2156.8005.6544.7253.9673.3442.8292.4042.0501.7591.5151.3091.1350.9880.8620.7550.6620.5830.5150.4570.4060.361
NCPppXH682
Resistance (kΩ)234.787168.515122.42289.95366.76650.06637.90628.96322.31317.33813.57110.7058.5036.8005.4744.4343.6132.9612.4402.0221.6831.4091.1851.0010.8490.7240.6200.5320.4590.3980.3460.3020.2640.232
NCPppXW682
Resistance (kΩ)195.652148.171113.34787.55968.23753.65042.50633.89227.21922.02117.92614.67412.08110.0008.3156.9485.8344.9174.1613.5353.0142.5862.2281.9251.6691.4521.2681.1100.9740.8580.7580.6720.5960.531
NCPppXH103 NCPppXV103
Resistance (kΩ)328.996237.387173.185127.77395.32771.74654.56441.81332.33025.19419.78515.65112.46810.0008.0726.5565.3564.4013.6353.0192.5212.1151.7811.5091.2841.0970.9410.8100.7010.6080.5300.4630.4060.358
Resistance (kΩ)293.478222.256170.021131.338102.35580.47463.75950.83840.82833.03226.88822.01018.12115.00012.47210.4228.7517.3756.2415.3024.5213.8793.3412.8872.5032.1781.9021.6641.4611.2871.1371.0070.8950.797
NCPppXH153
Resistance (kΩ)Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
517.912371.724270.048198.426147.278110.43983.61763.88849.22138.24529.93623.61318.75615.00012.0749.7807.9696.5315.3824.4593.7133.1082.6132.2081.8731.5971.3671.1741.0130.8780.7630.6650.5820.511
NCPppXW153
Resistance (kΩ)
Continued on the following page.
25.15418.65513.97910.5788.0796.2204.8293.7772.9772.3621.8881.5181.2291.0000.8190.6740.5580.4640.3880.3260.2750.2330.1990.1700.1460.1260.1090.0940.0820.0720.0630.0560.0490.044
NCPppXQ102
Resistance (kΩ)51.79137.17227.00519.84314.72811.0448.3626.3894.9223.8252.9942.3611.8761.5001.2070.9780.7970.6530.5380.4460.3710.3110.2610.2210.1870.1600.1370.1170.1010.0880.0760.0670.0580.051
NCPppXW152
Resistance (kΩ)3950K 3950K
3500K 3380K 3950K 3380K 3900K 3380K 3950K
3650K 3950K2.2kΩ 3.3kΩ
4.7kΩNCPppXW472
162.279116.47484.61562.17346.14734.60426.20020.01815.42311.9849.3807.3995.8774.7003.7833.0642.4972.0461.6861.3971.1640.9740.8190.6920.5870.5000.4280.3680.3180.2750.2390.2080.1820.160
Resistance (kΩ)3950K4.7kΩ 6.8kΩ 6.8kΩ 10kΩ 10kΩ 15kΩ 15kΩ
1kΩ
21.26616.15012.3479.5037.3655.7474.5163.5722.8442.2801.8391.4921.2181.0000.8250.6850.5710.4790.4030.3410.2900.2470.2120.1820.1570.1360.1190.1040.0910.0800.0700.0620.0550.049
NCPppXM102
Resistance (kΩ)3500K1kΩ
31.89924.22518.52014.25511.0478.6216.7735.3584.2663.4192.7582.2381.8271.5001.2381.0270.8570.7180.6050.5120.4350.3710.3180.2740.2360.2050.1780.1550.1360.1200.1050.0930.0830.074
NCPppXM152
Resistance (kΩ)3500K1.5kΩ
46.78635.53027.16220.90716.20312.6449.9347.8586.2575.0154.0453.2832.6802.2001.8161.5071.2571.0530.8870.7510.6380.5440.4660.4010.3460.3000.2610.2280.2000.1750.1550.1370.1210.108
NCPppXM222
Resistance (kΩ)3500K2.2kΩ
70.17953.29540.74331.36024.30418.96614.90111.7879.3867.5236.0674.9244.0193.3002.7242.2601.8851.5801.3311.1260.9570.8160.7000.6020.5200.4500.3920.3420.2990.2630.2320.2050.1820.162
NCPppXM332
Resistance (kΩ)3500K3.3kΩ1.5kΩ
Temp. (°C)B-ConstantResistance
Part Number
Temp. (°C)B-ConstantResistance
Part Number
Detailed Resistance - Temperature Tables are downloadable from the following URL.
http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en
15
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Temp. Sensor and Compensation Chip Type Temperature Characteristics (Center Value)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
3
Continued from the preceding page.
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
7318.8815140.2283648.2242615.3851893.0181382.8131019.059757.379567.499428.575326.121249.981192.979150.000117.37092.43373.25258.40646.84637.80330.67125.01820.51316.90213.99311.6389.7218.1556.8695.8104.9334.2063.6013.096
NCPppWL154
Resistance (kΩ)7899.4665466.1183834.4992720.5231951.2161415.5651036.984767.079572.667431.264327.405250.538193.166150.000117.28192.29373.09058.24046.66537.60530.45324.80420.29316.67913.77611.4289.5207.9666.6885.6394.7724.0523.4542.955
NCPppWM154
Resistance (kΩ)
1610.1541130.850802.609575.385416.464304.219224.193166.623124.85094.28771.74754.99642.45533.00025.82220.33516.11512.84910.3068.3176.7485.5044.5133.7183.0782.5602.1391.7941.5111.2781.0850.9250.7920.681
NCPppWL333
Resistance (kΩ)1747.9201245.428898.485655.802483.954360.850271.697206.463158.214122.25995.22774.73059.06547.00037.64330.33424.59120.04816.43313.53911.2099.3287.7986.5445.5184.6743.9723.3882.9022.4942.1501.8601.6151.406
NCPppWB473
Resistance (kΩ)2293.2491610.6051143.110819.487593.146433.281319.305237.312177.816134.287102.18478.32760.46747.00036.77628.96222.95218.30114.67911.8459.6107.8396.4275.2964.3843.6463.0462.5552.1521.8201.5461.3181.1280.970
NCPppWL473
Resistance (kΩ)
4485K 4500K
4485K 4050K 4485K
150kΩ 150kΩ
33kΩ 47kΩ 47kΩ
Temp. (°C)B-ConstantResistance
Part Number
Temp. (°C)B-ConstantResistance
Part Number
4879.2543426.8182432.1491743.5901262.012921.875679.373504.919378.333285.717217.414166.654128.653100.00078.24761.62248.83538.93731.23125.20220.44816.67913.67511.2689.3297.7586.4815.4374.5803.8733.2892.8042.4002.064
NCPppWL104
Resistance (kΩ)4485K100kΩ
2990.0412100.2471494.1131075.679782.705575.674427.712320.710242.768185.300142.603110.60286.41568.00053.87142.95434.46027.81422.57218.42215.11312.45910.3258.5927.1856.0335.0874.3093.6613.1242.6752.2991.9831.715
NCPppWF683
Resistance (kΩ)3317.8932330.2371653.8621185.641858.168626.875461.974343.345257.266194.287147.841113.32587.48468.00053.20841.90333.20826.47721.23717.13713.90411.3429.2997.6626.3435.2764.4073.6973.1142.6342.2361.9071.6321.403
NCPppWL683 NCPppWF104
Resistance (kΩ)4397.1193088.5992197.2251581.8811151.037846.579628.988471.632357.012272.500209.710162.651127.080100.00079.22263.16750.67740.90433.19527.09122.22418.32315.18412.63510.5668.8737.4816.3375.3844.5943.9343.3802.9162.522
Resistance (kΩ)4250K 4485K 4250K68kΩ 68kΩ 100kΩ
NCP18WF104F
4205.6862966.4362118.7891531.3191118.422825.570615.526463.104351.706269.305207.891161.722126.723100.00079.43963.50951.08441.33633.62827.51022.62118.69215.52512.94710.8499.1297.7136.5465.5724.7644.0873.5183.0402.634
Resistance (kΩ)4200K
100kΩ±1%
NCPppXW223
759.605545.196396.070291.025216.008161.977122.63893.70272.19156.09343.90734.63327.50922.00017.70914.34411.6889.5787.8946.5405.4464.5593.8323.2392.7482.3422.0041.7221.4861.2871.1190.9750.8540.750
Resistance (kΩ)1073.436753.900535.073383.590277.643202.813149.462111.08283.23362.85847.83136.66428.30422.00017.21413.55710.7448.5666.8715.5444.4983.6693.0092.4792.0521.7071.4261.1961.0080.8520.7240.6170.5280.454
NCPppWL223
Resistance (kΩ)1227.263874.449630.851460.457339.797253.363190.766144.964111.08785.84266.86152.47041.47133.00026.43021.29817.26614.07611.5389.5067.8706.5495.4754.5953.8743.2822.7892.3792.0381.7511.5091.3061.1340.987
NCPppWB333
Resistance (kΩ)1451.0491019.238725.084522.021379.842279.371207.566155.639117.81489.92569.20453.67541.93733.00026.14320.84516.72313.49810.9548.9407.3346.0465.0114.1703.4872.9282.4692.0911.7771.5161.2981.1160.9620.832
NCPppWF333
Resistance (kΩ)
Continued on the following page.
3950K 4485K 4050K 4250K22kΩ 22kΩ 33kΩ 33kΩ
2735.3591937.3911389.3451008.014738.978547.456409.600309.217235.606180.980140.139109.34485.92968.00054.16743.42135.01628.40623.16618.99715.65712.96710.7949.0217.5756.3875.4074.5983.9223.3592.8872.4892.1551.870
NCPppWD683
Resistance (kΩ)4150K68kΩ
430.434325.976249.364192.629150.121118.02993.51474.56359.88148.44639.43632.28226.57722.00018.29215.28512.83410.8179.1547.7776.6315.6904.9014.2343.6713.1952.7902.4412.1421.8881.6681.4771.3121.169
NCPppXH223
Resistance (kΩ)3380K22kΩ
Detailed Resistance - Temperature Tables are downloadable from the following URL.
http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en
16
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Temp. Sensor and Compensation Chip Type Temperature Characteristics (Center Value)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
4
Continued from the preceding page.
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
11585.8848016.9735623.9313990.1002861.7842076.1621520.9091125.049839.912632.521480.194367.455283.310220.000172.012135.364107.19885.41968.44155.15344.66536.37929.76324.46220.20516.76113.96211.6849.8098.2706.9985.9425.0674.334
NCPppWM224
Resistance (kΩ)24751.66117127.16912014.7628524.3056113.8114435.4373249.2162403.5151794.3581351.2941025.870785.018605.252470.000367.480289.186229.014182.485146.215117.82895.42077.71863.58452.26043.16635.80829.82824.96120.95517.66814.95112.69510.8249.259
NCPppWM474
Resistance (kΩ)4500K 4500K220kΩ 470kΩ
Temp. (°C)B-ConstantResistance
Part Number NCPppWL224
10734.3587539.0015350.7293835.8982776.4272028.1261494.6201110.822832.332628.577478.310366.639283.036220.000172.143135.569107.43685.66268.70855.44444.98436.69430.08524.78920.52317.06814.25811.96110.0758.5217.2366.1695.2814.540
Resistance (kΩ)4485K220kΩ
Detailed Resistance - Temperature Tables are downloadable from the following URL.
http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en
17
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Temp. Sensor and Compensation Chip Type Temperature Characteristics (Center Value)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Temp. Sensor and Compensation Chip Type !Caution/Notice
18
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Caution (Storage and Operating Conditions)This product is designed for application in an ordinary environment (normal room temperature, humidity and atmospheric pressure). Do not use under the following conditions because all these factors can deteriorate the product characteristics or cause failures and burn-out.1. Corrosive gas or deoxidizing gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.)
2. Volatile or flammable gas3. Dusty conditions4. Under vacuum, or under high or low pressure5. Wet or humid locations6. Places with salt water, oils, chemical liquids or organic solvents7. Strong vibrations8. Other places where similar hazardous conditions exist
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent secondary damages that may be caused by the abnormal function or the failure of our product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, thefollowing storage condition is recommended.1. Storage condition: Temperature -10 to +40 degrees C Humidity less than 75%RH (not dewing condition)2. Storage term: Use this product within 6 months after delivery by first-in and first-out stocking system.3. Storage place: Do not store this product in corrosive gas (Sulfuric acid gas, Chlorine gas, etc.) or in direct sunlight.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Notice (Handling)The ceramic of this product is fragile, and care mustbe taken not to load an excessive press-force or not to give a shock at handling. Such forces may cause cracking or chipping.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Locate this product horizontal to the direction in which stress acts.
Keep this product on the PC Board away from the Separation Line. Worst ← A-C-B-D → Better
Component Direction
Mounting Close to Board Separation Line
A
B
D
CPerforationHoles
Slit
1. Mounting Position
2. Allowable Soldering Temperature and Time
Choose a mounting position that minimizes the stress imposed on the chip during flexing or bending of the board.
(a) Solder within the temperature and time combinations indicated by the slanted lines in the following graphs.
(b) Excessive soldering conditions may cause dissolution of metallization or deterioration of solder-wetting on the external electrode.
(c) In case of repeated soldering, the accumulated soldering time should be within the range shown in the figure below. (For example, Reflow peak temperature: 260°C, twice -> The total accumulated soldering time at 260°C is within 30 seconds.)
Continued on the following page.
Allowable Reflow Soldering Temp. and Time
Allowable Reflow Soldering Temp. and Time
Time (sec.)
Tem
pera
ture
(°C
)
280
270
260
250
240
230
220
2100 10 20 30
Time (sec.)
Tem
pera
ture
(°C
)
280
270
260
250
240
230
220
2100 1109020 30 40 50 60 70 1008010
Time (sec.)
Tem
pera
ture
(°C
)280
270
260
250
240
230
2200 9020 30 40 50 60 70 8010
NCP03/15 Series
Allowable Flow Soldering Temp. and Time
NCP18/21 Series
1
Notice (Soldering and Mounting)
Temp. Sensor and Compensation Chip Type !Caution/Notice
19
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
For removing the flux after soldering, observe the following points in order to avoid deterioration of the characteristics or any change of the external electrodes' quality. • Please keep mounted parts and a substrate from an
occurrence of resonance in ultrasonic cleaning. • Please do not clean the products in the case of using a
non-washed type flux.
(1) Solder and Paste(a) Reflow Soldering: NCP03/15/18/21 Series
Use RA/RMA type or equivalent type of solder paste. For your reference, we are using the solder paste below for any internal tests of this product.•RMA9086 90-4-M20 (Sn:Pb=63wt%:37wt%)(Manufactured by Alpha Metals Japan Ltd.)•M705-221BM5-42-11 (Sn:Ag:Cu=96.5wt%:3.0wt%:0.5wt%)(Manufactured by Senju Metal Industry Co., Ltd.)
(b) Flow Soldering: NCP18/21 SeriesWe are using the solder paste below for any internal tests of this product.
•Sn:Pb=63wt%:37wt%•Sn:Ag:Cu=96.5wt%:3.0wt%:0.5wt%
(2) FluxUse rosin type flux in soldering process.If the flux listed below is used, some problems might be caused in the product characteristics and reliability.Please do not use the following flux.
• Strong acidic flux (with halide content exceeding 0.1wt%).
• Water-soluble flux(*Water-soluble flux can be defined as non rosin type flux including wash-type flux and non-wash-type flux.)
NCP03/15 NCP18/21
Continued from the preceding page.
4. Solder and Flux
5. Cleaning Conditions
After cleaning, promptly dry this product.6. Drying
Isopropyl Alcohol
Less than 5 minutes at room temp. or less than 2 minutes at 40°C max.
Less than 5 minutes and
20W/r Frequency of 28kHz to 40kHz
Isopropyl Alcohol
Less than 5 minutes at room temp. or less than 2 minutes at 40°C max.
Less than 1 minute and
20W/r Frequency of several 10kHz to 100kHz
Solvent
Dipping Cleaning
Ultrasonic Cleaning
3. Recommended Temperature Profile for Soldering(a) Insufficient preheating may cause a crack on ceramic
body. The difference between preheating temperature and maximum temperature in the profile shall be 100 °C.
(b) Rapid cooling by dipping in solvent or by other means is not recommended.
* In case of repeated soldering, the accumulated soldering time should be within the range shown in the figure 2 above.
Reflow Soldering Conditions
Reflow Soldering Conditions
Tem
pera
ture
(°C
)
Preheating (in air) SolderingGradual Cooling
(in air)300
200
100
01-2 min. *10sec.
Preheating: 160±10°C, 1-2 min.Soldering: 230-260°C, 10sec.
Tem
pera
ture
(°C
)
Preheating (in air) SolderingGradual Cooling
(in air)300
200
100
01-2 min. *20sec.
Preheating: 160±10°C, 1-2 min.Soldering: 230-270°C, 20sec.
Tem
pera
ture
(°C
)
Preheating (in air) SolderingGradual Cooling
(in air)300
200
100
01-2 min. *20sec.
Preheating: 160±10°C, 1-2 min.Soldering: 240-270°C, 20sec.
NCP03/15 Series
Flow Soldering Conditions
NCP18/21 Series
Continued on the following page.
2
Temp. Sensor and Compensation Chip Type !Caution/Notice
20
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Thin or insufficient adhesive may result in loose component contact with land during flow soldering.Low viscosity adhesive causes chips to slip after mounting.
NCP03
NCP15
NCP18/NCP21
100µm
150µm
200µm
1/3EVTVE
1/3EVTVE
0.2mmVTVE
Part Number The Solder Paste Thickness T
Reference: Optimum Solder Amount
TE
Electrode
Solder Solder
Continued from the preceding page.
The amount of solder is critical. Standard height of fillet is shown in the table below.Too much soldering may cause mechanical stress, resulting in cracking, mechanical and/or electronic damage.
7. Printing Conditions of Solder Paste
8. Adhesive Application and Curing
3
Temp. Sensor and Compensation Chip Type !Caution/Notice
21
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
NCP03
NCP15
NCP18
NCP21
15,000
10,000
4,000
-
-
4,000
Part NumberPaper Tape
Quantity (pcs.)
Embossed Tape
(in mm)
(in mm)
40 min.190-250
Vacant Section
210-250
Top Tape aloneCover Tape alone
Leader Unit
Trailer Unit
Chip-mounting Unit
Direction of Feed
ø180
ø21.0±0.8
ø13.0±0.2
ø60
2.0±0.5
9.013.0±1.0
(1) A tape in a reel contains Leader unit and Trailer unit where
products are not packed. (Please refer to the figure at the
right.)
(2) The top and base tapes or, plastic and cover tape are not
stuck at the first five pitches minimum.
(3) A label should be attached on the reel. (MURATA's part
number, inspection number and quantity should be marked
on the label.)
(4) Taping reels are packed in a package.
1. Dimensions of Reel
2. Taping Method
Tape Carrier Packaging
Minimum Quantity Guide
Continued on the following page.
W0Y1.5
W1.0Y0
W1.
0Y
0
1
Temp. Sensor and Compensation Chip Type Package
22
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
(1) Other Conditions
(a) Packaging
Products are packaged in the cavity of the base tape and
sealed by top tape and bottom tape.
(b) Tape
Top tape and bottom tape have no joints and products
are packaged and sealed in the cavity of the base tape,
continuously.
(2) Peeling Force of Top Tape
(3) Pull Strength
Pull strength of top tape is specified at 10N minimum.
Pull strength of bottom tape should be specified 5N minimum.
3. Paper Tape (NCP03/15/18 Series)
NCP15 Series
NCP18 Series
1.1 max.4.0±0.1 4.0±0.12.0±0.05
ø1.5+0.1/–0
1.75
±0.1
3.5±
0.05
8.0±
0.3
Direction of Feed
1.05∗
0.8 max.4.0±0.12.0±0.05
ø1.5+0.1/–0 1.75
±0.1
3.5±
0.05
1.15
∗
8.0±
0.3
Direction of Feed
0.65∗
(in mm)∗ Reference Value
∗ Reference Value
165-180 ° F
∗ 1 Peeling angle: 165 to 180 degrees against the fixed surface of tape.
∗ 2 Peeling speed: 300mm/min.
∗ 3 Peeling force: 0.1 - 0.6N
Continued on the following page.
Continued from the preceding page.1.
85∗
∗ Reference Value
NCP03 Series
0.5 max.4.0±0.12.0±0.05
ø1.5+0.1/–0 1.75
±0.1
3.5±
0.05
0.68
∗
8.0±
0.3
Direction of Feed
0.38∗
2
Temp. Sensor and Compensation Chip Type Package
23
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
∗ 1 Peeling angle: 165 to 180 degrees against the fixed surface of tape.
∗ 2 Peeling speed: 300mm/min.
∗ 3 Peeling force: 0.1 - 0.7N
F165-180 °
Continued from the preceding page.
(2) Peeling Force of Cover Tape
(3) Tape Strength
Pull strength of Embossed tape and Cover tape should be
specified 10N minimum.
(1) Other Conditions
(a) Packaging
Products are packaged in each cavity of the Embossed
tape and sealed by Cover tape.
(b) Tape
Cover tape has no joints.
4. Embossed Tape (NCP21 Series)
1.050.2
4.0±0.12.0±0.05
4.0±0.1 φ1.5
1.75
±0.1
φ1.0 1.45∗ ∗ Reference Value
3.5±
0.05
8.0±
0.3
Direction of Feed
2.25
∗
(in mm)
+0.3-0
+0.1-1
3
Temp. Sensor and Compensation Chip Type Package
24
4
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
25
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor Thermo String Type
1.2±0.4
25 to
100
±211
0 to
150
±3
3+2/
-1
1.2±0.4
ø0.30±0.05
The full length 25mm, 30 to 150mm Interval 10mm. (in mm)
1.2±0.4
25 to
100
±211
0 to
150
±3
3+2/
-1
1.2±0.4
ø0.30±0.05
The full length 25mm, 30 to 150mm Interval 10mm. (in mm)
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Operating Currentfor Sensor (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Thermal TimeConstant(25°C) (s)
NXFT15XH103FApBppp 10k ±1% 3380 ±1% 3423 3431 3452 0.12 7.5 1.5 4
NXFT15WB473FApBppp 47k ±1% 4050 ±1% 4091 4097 4114 0.06 7.5 1.5 4
NXFT15WF104FApBppp 100k ±1% 4250 ±1% 4303 4311 4334 0.04 7.5 1.5 4
p is the filled with lead shape (1: twist, 2: without twist).
ppp is the filled with Total-length codes. (25mm, 30 to 150mm interval 10mm, ex. 050=50mm)
Operating Current for Sensor rises Thermistor's temperature by 0.1°CRated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 30°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
NXFT15_1B Type(twist)
NXFT15_2B Type(without twist)
This product is a small flexible lead type NTC Thermistor with a small head and a thin lead wire.
Features1. High accuracy and highly sensitive temperature sensing is mode possible by the small size and high accuracy NTC Thermistor.2. Narrow space temperature sensing is made possible by the small sensing head and the thin lead wire.3. Flexibility and a wide variety of lengths (25 mm to 150mm) enables the design of flexible temperature sensing architectures. 4. This product is compatible with our 0402 (EIA) size chip Thermistor.5. Excellent long-term aging stability6. This is halogen free product. * * Cl= max.900ppm, Br=max.900ppm and Cl+Br=max.1500ppm7. NXFT series are recognized by UL/cUL (UL1434, File No. E137188).
Applications1. Temperature compensation for transistor, IC and crystal oscillator in mobile communications2. Temperature sensor for rechargeable batteries3. Temperature compensation of LCD4. Temperature compensation in general use of electric circuits
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Hold the lead wires as in Fig-3. Bend by 90 degrees and again bend back to the initial position. Then bend to the other side by 90 degrees and again bend back to the initial position. After bending process, 10N force for 3 seconds shall be applied to the lead wire.
Fig-3
10Lead WireBending Strength
· Lead wire does not break.
Continued on the following page.
The lead wire shall be inserted in a ø1.0mm hole until resin part contacts with a substrate as shown in fig.-2, and 1N force for 10 seconds shall be applied to the lead wire.
Fig-2
9Lead WirePull Strength
· Resistance (R25°C) fluctuation rate: less than ±1%.· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
Both lead wires are dipped into flux (25wt% colophony <JIS K 5902> isopropyl alcohol <JIS K 8839>) for 5 to 10 seconds. Then both lead wires are dipped into 235±5°C solder <JIS Z 3282 H60A> for 2±0.5 seconds according to Fig-1.
8 Solderability More than 90% of lead wire surface shall be covered by solder.
Both lead wires are dipped into 350±10°C solder for 3.5±0.5 seconds, or 260±5°C solder for 10±1 seconds according to Fig-1 (solder <JIS Z 3282 H60A>).
Fig-1
7Resistance toSoldering Heat
· Resistance (R25°C) fluctuation rate: less than ±1%.· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
2mm length of coating resin from the top of Thermistor is to be dipped into beads of lead (Pb), and DC100V 1 minute is applied to circuit between beads of lead (Pb) and lead wire.
6Insulation Break -down Voltage
· No damage electrical characteristics at DC100 V, 1 min.
85±2°C in air, with 'Operating Current for Sensor' for 1000 +48/-0 hrs.
5High TemperatureLoad
-40 +0/-3°C, 30 minutes in air+25±2°C, 10 to 15 minutes in air+125±2°C, 30 minutes in air + 25 +2/-0°C, 10 to 15 minutes in air (1 cycle)Continuous 100 cycles, without loading.
4Temperature Cycle
60±2°C, 90 to 95%RH in air, for 1000 +48/-0 hours without loading.
3HumidityStorage Test
· Resistance (R25°C) fluctuation rate: less than ±2%.· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
-40 +0/-3°C in air, for 1000 +48/-0 hours without loading.2Low TemperatureStorage Test
125±2°C in air, for 1000 +48/-0 hours without loading.1High TemperatureStorage Test · Resistance (R25°C) fluctuation rate: less than ±1%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
No. Test MethodsSpecificationsItem
* · R25 is zero-power resistance at 25°C.· B25/50 is calculated by zero-power resistance of Thermistor in 25°C -50°C.· After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).
Solder
1 to 2mm
1N (10 sec.)
10N (3 sec.)
Temperature Sensor Thermo String Type Specifications and Test Methods
26
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Continued from the preceding page.
NTC Thermistor shall be fixed to the vibration test equipment. Vibration of total 1.5 mm amplitude, Frequency sequence of 10Hz - 55Hz - 10Hz in 1 minute, shall be applied for right angled 3 directions for each 2 hours duration.
12 Vibration
NTC Thermistor shall be dropped without any force onto concrete floor from 1 meter height one time.
11 Free Fall
· Resistance (R25°C) fluctuation rate: less than ±1%.· B-Constant (B25/50°C) fluctuation rate: less than ±1%.· No visible damage at resin part.
* · R25 is zero-power resistance at 25°C.· B25/50 is calculated by zero-power resistance of Thermistor in 25°C -50°C.· After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).
No. Test MethodsSpecificationsItem
Mount
Solder is attached from the reverse side.
OscillatingDirection Z
Oscillating Direction X
OscillatingDirection Y
Temperature Sensor Thermo String Type Specifications and Test Methods
27
5
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
28
6
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor Lead Type
This product is a sensor type NTC Thermistor developed by our unique ceramic technology and automatic assemble, to be used in normal temperature ranges.
Features1. High accuracy of B-Constant tolerance +/-0.5% +/-1% of resistance and +/-0.5% of B-Constant is realized due to technical advantages of the material and manufacturing process.2. Quick response This product provides faster response time due to its smaller size.3. Taping type is available.4. Strong lead strength Original lead-wiring technique assures reliable connection. It can be formed and bent flexibly according to the mounting conditions.
Applications1. Rechargeable batteries2. Battery charging circuits3. Printer heads4. DC fan motors5. Home appliance equipment
Solder Plated Copper Ply Wireø0.4±0.03
31±1
2.5±1.0
6.0
max
.
3.0 max. (∗3.3 max.) 1.8 max. (∗2.5 max.)
Epoxy Resin
(in mm)
∗ Applicable to NTSA0XM202, NTSA0WB203 and NTSA0WC303 Types.
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Thermal TimeConstant(25°C) (s)
NTSA0XM202pE1B0 2.0k 3500 ±0.5% 3523 3526 3543 1.05 21 2.1 7
NTSA0XR502pE1B0 5.0k 3700 ±1% 3727 3738 3760 0.68 15 1.5 7
NTSA0XH103pE1B0 10k 3380 ±0.5% 3428 3434 3455 0.38 15 1.5 7
NTSA0XV103pE1B0 10k 3900 ±0.5% 3930 3934 3944 0.46 15 1.5 7
NTSA0WB203pE1B0 20k 4050 ±1% 4078 4080 4096 0.31 21 2.1 7
NTSA0WC303pE1B0 30k 4100 ±1% 4128 4130 4147 0.26 21 2.1 7
NTSA0WD503pE1B0 50k 4150 ±1% 4205 4213 4234 0.20 15 1.5 7
NTSA0WF104pE1B0 100k 4250 ±1% 4303 4311 4334 0.14 15 1.5 7
p is filled with resistance tolerance codes (F: ±1%, E: ±3%).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 35°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°CTaping type of part numbers with "N6A0" is available (Lead Spacing=5mm, Lead Diameter=ø0.5mm).
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
29
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsTemperature Sensor Lead Insulation Type
This product is a sensor type NTC Thermistor developed by our unique ceramic technology and automatic assemble, to be used in normal temperature ranges.
Features1. Electric insulation on lead wire2. Excellent bending resistance due to suitable hardness of surface coating3. Easy handling due to most suitable hardness of surface of coating4. High accuracy of B-Constant tolerance +/-0.5% +/-1% of resistance and +/-0.5% of B-Constant is realized due to technical advantages of the material and manufacturing processes.
Applications1. Rechargeable batteries2. Battery charging circuits3. Printer heads4. DC fan motors5. Home appliance equipment
3.0 max. (∗3.8 max.)
0.60-0.952.5
+1.5−0.5
2.0 max. (∗2.5 max.)
ø0.4±0.03
(Solder PlatedCopper Ply Wire)
(in mm)
5±1
27.0
±2.0
3±1.
5
(Coa
ting
Are
a)
∗ Applicable to NTSD0XM202, NTSD0WB203 and NTSD0WC303 Types.
NTSD0 Series
3.0 max. (∗3.8 max.) 2.0 max. (∗2.5 max.)
ø0.45±0.05Sn-Ag Solder Copper Wire
∗ NTSD1XM202/NTSD1WB203/NTSD1WC303 Types
Epoxy Resin
ø0.46±0.03Polyurethane Wire
(in mm)
L ±2
.0
2.5±
1.2
(0.8)
2.5+1.5-0.5
TypeNTSD1_FPB30
NTSD1_FPB40
NTSD1_FPB50
L (mm)30
40
50
NTSD1 Series
NTSD0 Series
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Thermal TimeConstant(25°C) (s)
NTSD0XM202pE1B0 2.0k 3500 ±0.5% 3523 3526 3543 1.05 21 2.1 7
NTSD0XR502pE1B0 5.0k 3700 ±1% 3727 3738 3760 0.68 15 1.5 7
NTSD0XH103pE1B0 10k 3380 ±0.5% 3428 3434 3455 0.38 15 1.5 7
NTSD0XV103pE1B0 10k 3900 ±0.5% 3930 3934 3944 0.46 15 1.5 7
NTSD0WB203pE1B0 20k 4050 ±1% 4078 4080 4096 0.31 21 2.1 7
NTSD0WC303pE1B0 30k 4100 ±1% 4128 4130 4147 0.26 21 2.1 7
NTSD0WD503pE1B0 50k 4150 ±1% 4205 4213 4234 0.20 15 1.5 7
NTSD0WF104pE1B0 100k 4250 ±1% 4303 4311 4334 0.14 15 1.5 7
p is filled with resistance tolerance codes (F: ±1%, E: ±3%).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 35°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
NTSD1 Series
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Thermal TimeConstant(25°C) (s)
NTSD1XM202FPBpp 2.0k ±1% 3500 ±0.5% 3523 3526 3543 1.05 21 2.1 7
NTSD1XR502FPBpp 5.0k ±1% 3700 ±1% 3727 3738 3760 0.68 15 1.5 7
NTSD1XH103FPBpp 10k ±1% 3380 ±0.5% 3428 3434 3455 0.38 15 1.5 7
NTSD1XV103FPBpp 10k ±1% 3900 ±0.5% 3930 3934 3944 0.46 15 1.5 7
NTSD1WB203FPBpp 20k ±1% 4050 ±1% 4078 4080 4096 0.31 21 2.1 7
NTSD1WC303FPBpp 30k ±1% 4100 ±1% 4128 4130 4147 0.26 21 2.1 7
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
30
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part NumberResistance
(25°C)(ohm)
B-Constant(25-50°C)
(K)
B-Constant(25-80°C)
(Reference Value) (K)
B-Constant(25-85°C)
(Reference Value) (K)
B-Constant(25-100°C)
(Reference Value) (K)
Permissive OperatingCurrent (25°C)
(mA)
Rated ElectricPower (25°C)
(mW)
Typical DissipationConstant (25°C)
(mW/°C)
Thermal TimeConstant(25°C) (s)
Continued from the preceding page.
NTSD1WD503FPBpp 50k ±1% 4150 ±1% 4205 4213 4234 0.20 15 1.5 7
NTSD1WF104FPBpp 100k ±1% 4250 ±1% 4303 4311 4334 0.14 15 1.5 7
pp is filled with Total-length codes (30, 40, 50).
Rated Electric Power shows the required electric power that causes Thermistor's temperature to rise to 35°C by self heating, at ambient temperature of 25 °C.
Operating Temperature Range: -40°C to +125°C
Temperature Tolerance - Temperature Characteristics
Resistance Tolerance: +/-1% B-Constant Tolerance: +/-1%
Temperature (°C)
Tem
pera
ture
Tol
eran
ce (
±°C
)
0
1.0
2.0
3.0
-50 0 50 100 150
Resistance Tolerance: +/-1% B-Constant Tolerance: +/-0.5%
Temperature (°C)
Tem
pera
ture
Tol
eran
ce (
±°C
)
0
1.0
2.0
3.0
-50 0 50 100 150
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
44.65733.50525.38819.40214.96111.6449.1337.1985.7164.5713.6822.9872.4372.0001.6511.3711.1430.9580.8070.6830.5820.4970.4260.3670.3180.2760.2400.2100.1830.1610.1420.1250.1110.099
123.48492.29569.61452.86040.48031.27524.33919.15415.14811.9649.5207.6246.1605.0004.0823.3542.7732.2991.9141.6071.3561.1490.9780.8340.7140.6120.5270.4560.3960.3450.3020.2640.2320.205
195.652148.171113.34787.55968.23753.65042.50633.89227.21922.02117.92614.67412.08110.0008.3156.9485.8344.9174.1613.5353.0142.5862.2281.9251.6691.4521.2681.1100.9740.8580.7580.6710.5960.531
347.808248.591179.973131.83297.67973.11955.30142.25732.58225.32419.84715.67912.47810.0008.0686.5525.3534.3993.6353.0202.5212.1151.7831.5101.2841.0960.9390.8080.6980.6050.5270.4600.4030.354
NTSppXM202 NTSppXR502 NTSppXH103 NTSppXV103
Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)
1
733.007524.831380.184277.845205.260153.642116.01688.12567.52252.16840.61731.84725.15120.00016.01412.90210.4578.5276.9935.7714.7893.9923.3432.8092.3762.0201.7241.4761.2641.0850.9350.8120.7080.617
1149.500819.651591.391430.529316.870236.337177.842134.630102.81679.18361.46048.04537.83430.00023.95519.24915.56012.65710.3548.5257.0585.8694.9054.1133.4722.9452.5092.1431.8321.5711.3501.1711.0190.886
1948.5751387.289999.456728.895537.039399.167299.469226.186172.393132.857103.08980.43063.20150.00039.82531.91825.73320.87717.03413.92911.4399.4857.9066.6145.5584.6863.9673.3732.8782.4652.1181.8281.5831.374
4256.7523005.8882148.5141555.0201137.312839.314625.338469.127355.224272.045209.803162.713127.117100.00079.21563.15050.64940.88533.19527.01422.07918.22615.12412.59810.5428.8527.4636.3215.3744.5853.9253.3762.9132.520
NTSppWB203 NTSppWC303 NTSppWD503 NTSppWF104
Resistance (kΩ) Resistance (kΩ) Resistance (kΩ) Resistance (kΩ)3500K 3700K 3380K 3900K 4050K 4100K 4150K 4250K2.0kΩ 5.0kΩ 10kΩ 10kΩ 20kΩ 30kΩ 50kΩ 100kΩ
Y40Y35Y30Y25Y20Y15Y10Y505
101520253035404550556065707580859095100105110115120125
197.388149.395114.34588.38168.91554.16642.88934.19627.44522.16518.01014.72012.09910.0008.3096.9395.8244.9114.1603.5393.0242.5932.2331.9291.6731.4551.2701.1120.9760.8600.7590.6730.5980.532
NXFpXH103
Resistance (kΩ)Temp. (°C)B-ConstantResistance
Part Number
1690.5901215.320882.908647.911480.069359.009270.868206.113158.126122.26795.25674.75459.07547.00037.63630.32624.58320.04316.43313.54511.2239.3457.8186.5715.5484.7044.0043.4222.9362.5282.1841.8931.6461.436
NXFpWB473
Resistance (kΩ)4221.2802995.0402147.0001554.6001136.690839.019624.987469.678355.975272.011209.489162.559127.057100.00079.22263.16750.67740.90433.19527.09122.22418.32315.18412.63510.5668.8737.4816.3375.3844.5943.9343.3802.9162.522
NXFpWF104
Resistance (kΩ)3380K 4050K 4250K10kΩ 47kΩ 100kΩ
Temp. (°C)B-ConstantResistance
Part Number
Detailed Resistance - Temperature Tables are downloadable from the following URL.
http://search.murata.co.jp/Ceramy/CatsearchAction.do?sLang=en
Temperature Sensor Temperature Characteristics (Center Value)
31
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Temperature Sensor Thermo String Type/Lead Type !Caution/Notice
32
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Caution (Storage and Operating Conditions)This product is designed for application in an ordinary environment (normal room temperature, humidity and atmospheric pressure). Do not use under the following conditions because all these factors can deteriorate the product characteristics or cause failures and burn-out.1. Corrosive gas or deoxidizing gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.)
2. Volatile or flammable gas3. Dusty conditions4. Under vacuum, or under high or low pressure5. Wet or humid locations6. Places with salt water, oils, chemical liquids or organic solvents7. Strong vibrations8. Other places where similar hazardous conditions exist
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent secondary damages that may be caused by the abnormal function or the failure of our product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, thefollowing storage condition is recommended.1. Storage condition: Temperature -10 to +40 degrees C Humidity less than 75%RH (not dewing condition)2. Storage term: Use this product within 6 months after delivery by first-in and first-out stocking system.
3. Handling after unpacking: After unpacking, reseal product promptly or store it in a sealed container with a drying agent.4. Storage place: Do not store this product in corrosive gas (Sulfuric acid gas, Chlorine gas, etc.) or in direct sunlight.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Notice (Soldering and Mounting) NTS Series1. Be sure that the preheat-up does not melt the soldering of this product. Excessive heat may cause failure to open, short or insulation break down.2. Do not touch the body with soldering iron. The soldering point should be min. 5mm away from the root of lead wire.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Temperature Sensor Thermo String Type/Lead Type !Caution/Notice
33
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice (Soldering and Mounting) NXF Series
Notice (Handling)1. The ceramic element of this product is fragile, and care must be taken not to load an excessive press-force or not to cause a shock while handling. Such forces may cause cracking or chipping.2. Do not apply excessive force to the lead. Otherwise, it may cause the junction between lead and element to break or crack. Holding element by side lead wire is recommended when lead wire is bent or cut.
Please notice as shown below when you mount this product.1. When you solder this product, do not melt the solder in resin head. If you melt the solder in resin head, there is the possibility of breaks in the wire, shorts and breaks of the lead insulation. In case you cut the lead wire of this product less than 20mm from resin head, the heat of melted solder at lead wire edge is propagated easily to the resin head along the lead wire.2. Do not touch the resin head directly with solder iron. It may cause the melting of solder in resin head.
3. Do not separate the parallel lead wires 10mm or less from the resin head, when you separate parallel lead wires.4. If you mold by resin this product, please evaluate the quality before you use it.5. Do not bend the lead wire radius 1mm or less when you bend the lead wire.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Temperature Sensor Thermo String Type/Lead Type Package
34
7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item Code Dimensions (mm)
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Length from Hole Center to Component Center
Length from Hole Center to Lead
Body Diameter
Deviation along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Planes
Height of Component
Protrusion Length
Diameter of Sprocket Hole
Lead Diameter
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation across Tape
Portion to Cut in Case of Defect
Hold down Tape Width
Hold down Tape Position
Coating Extension on Lead
Body Thickness
P
P0
F
P2
P1
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
T
12.7
12.7±0.3
5.0+0.8/–0.2
6.35±1.3
3.85±0.8
3.5 max.
0±2.0
18.0±0.5
9.0±0.5
16.0±1.0
4.0 max.
+0.5 to –1.0
4.0±0.1
0.50±0.03
0.6±0.3
1.6 max.
1.0 max.
11.0+0/–2.0
11.0 min.
1.5±1.5
Up to the crimp point
2.6 max.
(in mm)
Minimum Order Quantity
Taping Dimensions (NTSA_N6A0 Series)
P2
P0I
L
P ∆S
H2
W2
W0
H0W1
W
t2 t1
∆h2 ∆h1
T
øD0
D
P1 ød
F
e
Part Number Minimum Quantity (pcs.)
Bulk
NXFT
NTSA_E1B0
NTSD0
NTSD1_30
NTSD1_40
NTSD1_50
-
3,000
-
-
-
-
1,000
500
500
500
200
200
Part Number Minimum Quantity (pcs.)
Ammo Pack Taping
NTSA_N6A0
-
-
-
-
-
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
35
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTC ThermistorsInrush Current Suppression Lead Type
This product effectively suppresses surge currents which are generated when switching power regulators are turned on.
Features1. Lead is not contained in the ceramic element, the terminations, the solder for inner connection or the coating resin.2. Most suitable for power supplies of less than 100W3. Excellent recovery characteristics due to resin coating with excellent heat characteristics4. Highly reliable
Applications1. Switching power supplies2. CRT monitors 3. Televisions4. VCR Power supplies 5. Other power circuits
Coating Extensionon Lead : to line A
10.0
max
.3.
5±1.
0
NTPAN : 23.0 max.NTPAJ : 20.0 max. 5.5 max.
10.0±1.5
ø0.8±0.05Sn plated Cu wire
A
(in mm)
NTPAN/NTPAJ Series
Coating Extensionon Lead : to line A
10.0
max
.3.
5±1.
0
NTPAD : 16.0 max.NTPAA : 12.0 max.
5.5 max.5.0 max.
7.5±1.5
ø0.8±0.05Sn plated Cu wire
A
(in mm)
NTPAD/NTPAA Series
Coating Extensionon Lead : to line A
6.0
max
.3.
5±1.
0
NTPA7 : 9.0 max.NTPA9 : 11.0 max.
5.0 max.
5.0±1.5
ø0.6±0.05Sn plated Cu wire
A
(in mm)
NTPA7/NTPA9 Series
Part NumberResistance
(25°C)(ohm)
Permissible Max.Current (25°C)
(A)
Permissible Max.Current (55°C)
(A)
Thermal TimeConstant (25°C)
(s)
Thermal DissipationConstant (25°C)
(mW/°C)
NTPAN3R0LDKB0 3.0 ±15% 5.4 4.7 135 26.8
NTPAN4R0LDKB0 4.0 ±15% 4.7 4.1 130 26.8
NTPAN6R0LDKB0 6.0 ±15% 3.9 3.4 130 26.8
NTPAJ4R0LDKB0 4.0 ±15% 4.0 3.5 125 21.8
NTPAJ6R0LDKB0 6.0 ±15% 3.4 2.9 125 21.8
NTPAJ8R0LDKB0 8.0 ±15% 3.0 2.6 130 21.8
NTPAJ100LDKB0 10.0 ±15% 2.6 2.2 130 21.8
NTPAD3R9LDNB0 3.9 ±15% 3.3 2.9 65 18.2
NTPAD5R1LDNB0 5.1 ±15% 3.0 2.6 85 18.8
NTPAD8R0LDNB0 8.0 ±15% 2.7 2.3 65 18.7
NTPAD160LDNB0 16.0 ±15% 2.0 1.7 100 19.1
NTPAA2R2LDNB0 2.2 ±15% 3.7 3.2 70 13.5
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
36
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Part NumberResistance
(25°C)(ohm)
Permissible Max.Current (25°C)
(A)
Permissible Max.Current (55°C)
(A)
Thermal TimeConstant (25°C)
(s)
Thermal DissipationConstant (25°C)
(mW/°C)
Continued from the preceding page.
NTPAA3R9LDNB0 3.9 ±15% 2.7 2.3 70 13.5
NTPAA5R1LDNB0 5.1 ±15% 2.5 2.2 70 13.5
NTPAA8R2LDNB0 8.2 ±15% 2.0 1.7 70 13.5
NTPAA100LDNB0 10.0 ±15% 1.7 1.5 70 13.5
NTPA9160LBMB0 16.0 ±15% 1.4 1.2 65 11.6
NTPA74R0LBMB0 4.0 ±15% 2.3 2.0 40 9.4
NTPA75R0LBMB0 5.0 ±15% 1.9 1.6 40 9.4
NTPA78R0LBMB0 8.0 ±15% 1.7 1.5 40 9.5
NTPA7100LBMB0 10.0 ±15% 1.4 1.2 40 9.5
NTPA7160LBMB0 16.0 ±15% 1.2 1.0 40 9.9
NTPA7220LBMB0 22.0 ±15% 1.0 0.88 40 9.1
NTPAD/NTPAA/NTPA9/NTPA7 series are also availabe on tape. The final alphabet of the part number should be "DNB0=>D6A0", "BNB0 =>B1A0".
Operating Temperature Range: -20°C to +160°C
Permissible Electrolytic Capacitor
Part Number
Voltage (AC)
NTPAN 8600µF
NTPAJ 5000µF
NTPAD 2700µF
NTPAA 1400µF
NTPA9 800µF
NTPA74R0700µF
NTPA78R0
NTPA75R0
NTPA7100570µF
NTPA7160400µF
NTPA7220
5972µF
3472µF
1875µF
972µF
556µF
486µF
396µF
278µF
4936µF
2870µF
1550µF
803µF
459µF
402µF
327µF
230µF
1777µF
1033µF
558µF
289µF
165µF
145µF
118µF
83µF
1493µF
868µF
469µF
243µF
139µF
122µF
99µF
69µF
1234µF
717µF
387µF
201µF
115µF
100µF
82µF
57µF
100Vrms 120Vrms 132Vrms 220Vrms 240Vrms 264Vrms
Application Circuit
NTC
−t˚
−
+
Determination of Allowable Current
Max
. Cur
rent
Rat
io
1.0
0
0.5
Ambient Temperature (˚C)20 40 60 80 100 120 140 160
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Current - R Ratio (RT/R25)/Current - Temperature Characteristics (Typical)
37
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
NTPAN3R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAN4R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAN6R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
) NTPAJ4R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAJ6R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAJ8R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Current - R Ratio (RT/R25)/Current - Temperature Characteristics (Typical)
38
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
NTPAJ100L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD3R9L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD5R1L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
) NTPAD8R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD160L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA2R2L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Current - R Ratio (RT/R25)/Current - Temperature Characteristics (Typical)
39
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
NTPAA3R9L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA5R1L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA8R2L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
) NTPAA100L Type
0.01
0.1
1
10
0.01 0.1 1 10
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
tem
pera
ture
(˚C
)
1
10
100
1000
Resistance RatioThermistor's Temperature
Ta=25°C
Current (A)
NTPA9160L Type
0.01
0.1
1
10
0.01 0.1 1 10
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
tem
pera
ture
(˚C
)
1
10
100
1000
Resistance RatioThermistor's Temperature
Ta=25°C
Current (A)
NTPA74R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Current - R Ratio (RT/R25)/Current - Temperature Characteristics (Typical)
40
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
NTPA75R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA78R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA7100L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
) NTPA7160L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA7220L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Inrush Current Suppression Lead Type !Caution/Notice
41
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Caution (Storage and Operating Conditions)
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent secondary damages that may be caused by the abnormal function or the failure of our product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, thefollowing storage condition is recommended.1. Storage condition: Temperature -10 to +40 degrees C Humidity less than 75%RH (not dewing condition)2. Storage term: Use this product within 6 months after delivery by first-in and first-out stocking system.
3. Handling after unpacking: After unpacking, reseal product promptly or store it in a sealed container with a drying agent.4. Storage place: Do not store this product in corrosive gas (Sulfuric acid gas, Chlorine gas, etc.) or in direct sunlight.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Notice (Soldering and Mounting)1. Be sure that the preheat-up does not melt the soldering of this product. Excessive heat may cause failure to open, short or insulation break down.2. Do not touch the body with soldering iron. The soldering point should be min. 5mm away from the root of lead wire.
1. This product is designed for the Switching Power Supply with smoothing capacitors. Other applications of this product may result in fire.2. Use this product within the specified maximum current. Otherwise it may catch fire in the worst case.3. Use this product with smoothing capacitor within the specified maximum capacitance value. Otherwise it may catch fire in the worst case.4. This product is designed for application in an ordinary environment (normal room temperature, humidity and atmospheric pressure). Do not use under the following conditions because all of these factors can deteriorate the product characteristics causing failure and burn-out.
(1) Corrosive gas or deoxidizing gas (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) Volatile or flammable gas (3) Dusty conditions (4) Under high or low pressure (5) Wet or humid conditions (6) Near with salt water, oils, chemical liquids or organic solvents (7) Strong vibrations (8) Other places where similar hazardous conditions exist.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Inrush Current Suppression Lead Type !Caution/Notice
42
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Notice (Handling)
Notice (Others)1. This product may allow passing higher current than its initial value when it receives inrush current again shortly after the previous one after it cools down and sufficiently recovers its original resistance. Be sure the highest current under actual condition remains within the operating repetition and the operating temperature.2. The resin coating of this product does not guarantee insulating. Keep an adequate insulating distance to surrounding parts.
1. When this product is operated, temperature of some areas may be about 160 (degree C). Use proper surrounding parts and material which withstand such temperature. If they are inadequate and kept at high temperature for a long time, they may be deteriorated or may produce harmful gas; such harmful gas may deteriorate the element of this product.2. This product does not have waterproof construction. Splashed water may cause failure mode such as deterioration of characteristics or current leak. Therefore, do not immerse it in water or any solvent.
3. The ceramic element of this product is fragile, and care must be taken not to load an excessive press-force or give a shock at handling. Such forces may cause cracking or chipping to the element.4. Do not apply excessive force to the lead wire. Otherwise, it may cause the junction between lead and element to break or crack. So, fix lead wire of element side when lead wire is bent or cut.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Inrush Current Suppression Lead Type Package
43
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Minimum Order Quantity
Part Number
Bulk
Minimum Quantity (pcs.)
-50
-100
400150
750300
1,000300
1,000500
Part Number
Ammo Pack Taping
Minimum Quantity (pcs.)
NTPAN_DKB0
NTPAJ_DKB0
NTPAD_DNB0
NTPAA_DNB0
NTPA9_BMB0
NTPA7_BMB0
-
-
NTPAD_D6A0
NTPAA_D6A0
NTPA9_B1A0
NTPA7_B1A0
Taping Dimensions (NTPAD/NTPAA_D6A0 Series)
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Length from Hole Center to Lead
Length from Hole Center to Component Center
Body Diameter
Deviation Along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Plane
Height of Component
Protrusion Length
Diameter of Sprocket Hole
Lead Diameter
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation Across Tape
Portion to Cut in Case of Defect
Hold down Tape Width
Hold down Tape Position
Coating Extension on Lead
P
P0
F
P1
P2
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
30.0
15.0±0.3
7.5±0.5
7.5±1.5
3.75±1.0
(refer to the table below)
Body Thickness T (refer to the table below)
±2.0
18.0±0.5
16.0±0.5
10.0 max.
W0.5 to Y6.0
4.0±0.1
0.8±0.05
0.6±0.3
2.0 max.
2.0 max.
11.5 min.
4.0 max.
to line A
CodeItem Dimensions (mm)
9.0±0.5
11.0+0–2.0
NTPAD
NTPAA
Type D (mm) T (mm)
16.0 max. 5.5 max.
12.0 max. 5.0 max.
W0
W2
W
W1
H0
H2
∆h2∆h1
e
∆SP2 P
D
P1
P0
F d
l
øD0
L
t2 t1
T
A
Continued on the following page.
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
Inrush Current Suppression Lead Type Package
44
8
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
Taping Dimensions (NTPA9/NTPA7_B1A0 Series)
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Length from Hole Center to Lead
Length from Hole Center to Component Center
Body Diameter
Deviation Along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Planes
Height of Component
Protrusion Length
Diameter of Sprocket Hole
Lead Diameter
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation Across Tape
Portion to Cut in Case of Defect
Hold down Tape Width
Hold down Tape Position
Coating Extension on Lead
P
P0
F
P1
P2
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
12.7
12.7±0.3
5.0
6.35±1.3
3.85±0.8
(refer to the table below)
Body Thickness T 5.0 max.
±1.5
18.0±0.5
16.0±1.0
6.0 max.
W0.5 to Y4.0
4.0±0.3
0.6±0.05
0.6±0.3
2.0 max.
1.5 max.
11.0 min.
4.0 max.
to line A
CodeItem Dimensions (mm)
9.0
11.0+0–2.0
+0.8–0.3
+0.5–0.75
W0
W2
W
W1
H0
H2
∆h2∆h1
e
∆SP2 P
D
A
P1
P0
F d
l
øD0
L
t2 t1
T
Type D (mm)
11.0 max.
9.0 max.
NTPA9
NTPA7
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011
!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
R44E.pdfFeb.21,2011