NT SERVER HARDWARE AND OS UPLOADING RELATED ISSUE SOLVING

A) Hardware Related Problem.Power issue: If the following steps are not happened, It means there may be some problem.a) zte server required 220v AC. So before giving power to

server always check the incoming ac supply(coming from commercial AC or inverter) voltage with millimeter

b) After plug in the power cord we switch on the power switch at the back then the LED (V5SBiY-5v standby voltage) at the main processor PCB(motherboard) beside SMPS turns into green. If it is not happened open the cover of the server-jack out & jack in the power cables coming from smps(power module to different PCB like processor PCB and hard disk PCB)

c) Then check the power button at the front side will be turn into red, if not then open the cover—check the data bus coming from the front panel power switch to X15 data bus clip at the right most corner of the main mother board (seeing from the back side).---if it is loosed from the clip, then insert the blue end of the data bus into the clip and insert the end into a specific level otherwise if you insert less there will be no light at the power button and if you insert much the button will turn into green and two LED V5 and V5SBY will remain green but the server will not be on.So you have to insert the blue end in between those two levels.

So in ideal condition when you put on the power switch the power button will turn into red(V5SBY will on) then after pressing the button V5 LED and other LEDs on that line will glow and the button will turn into green----the server will start running.If your Hard disk not receiving power check the data bus coming from mother board to hard disk’s PCB and also look corresponding LEDs which are at the back of the hard disk on the PCB are glowing or not.

B) OS uploading related problem.If you want to upload OS, before that RAID configuration must be done because we have multiple hard disks.→When booting will start press Ctrl+c to enter in the utility then flow the steps written in the manual of NT server for raid configuration.→After that you have to go to bios setup (press DEL/F1 at the time of booting)→Select boot agent CD drive----then insert the NT server software CD then restart.→That CD will process automatically→After that one window (written in Chinese) will come.→Go to the left most drop down list.→ Select the second option.→Now the whole window will convert into English.→ Go to server configuration at the left side of the window.→Then you have to fill the data at the right side for the options will come at the left side including the time setting, partition setting, IP setting, File system setting (that will be NTFS),OS

setting(OS name-windows server 2003 R2 standard edition, OS CD key required) and OS installing(when progress bar is around 8% system ask you for inserting the first OS CD-----when progress bar is around 80% it will ask for second CD)→After OS installing Windows setup will start. it will copy files to hard disk.→After that go to bios and select boot agent hard disk. (F10 for save the bios configuration)→ then restart.

Otherwise we can use a Different & Easy method and then………..

→ Collect automatic recovery CD.

→ Insert the CD, when booting will start continuously press F12 to

Boot from CD and do as system asking from you.

→After that one window (written in Chinese) will come.→Go to the left most drop down list.→ Select the second option.→Now the whole window will convert into English.→ Go to server configuration at the left side of the window.→Then you have to fill the data at the right side for the options will come at the left side including the time setting, partition setting, IP setting, File system setting (that will be NTFS), OS setting(OS name-windows server 2003 R2 standard edition, OS CD key required) and OS installing(when progress bar is around 8% system ask you for inserting the first OS CD-----when progress bar is around 80% it will ask for second CD)

→After OS installing Windows setup will start. it will copy files to hard disk. Then automatically windows server 2003 OS will start.→Then go to my computer desktop icon -----right click----manage---disk management-----format unhealthy drives ----give name to those drives.Now your NT server will be ready now upload SQL, oamback copy previous TG backup to default backup folder

This document created by----

Sougata ChakrabortyZTE Telecom India Pvt. Ltd.BSNL  IP TAX ProjectEast Zone

9836146999