NO. 1

TO THE DRAWINGS AND THE PROJECT MANUAL

PROJECT PROJECT PROJECT PROJECT NAMENAMENAMENAME:::: LA VEGA HIGH SCHOOL CLASSROOM ADDITION

CLIENTCLIENTCLIENTCLIENT NAMENAMENAMENAME:::: LA VEGA ISD

LOCATIONLOCATIONLOCATIONLOCATION:::: BELLMEAD, TEXAS

PROJECT NUMBER:PROJECT NUMBER:PROJECT NUMBER:PROJECT NUMBER: 1612-12-01

PROPOSAL DATE:PROPOSAL DATE:PROPOSAL DATE:PROPOSAL DATE: TUESDAY, MARCH 13, 2018 AT 2:00P.M.

ADDENDUM DATE:ADDENDUM DATE:ADDENDUM DATE:ADDENDUM DATE: THURSDAY, MARCH 8, 2018

For additional information regarding this project, contact Aubrey Slaybaugh at

800.687.1229 or aslaybaugh@huckabee-inc.com.

THIS ADDENDUM INCLUDTHIS ADDENDUM INCLUDTHIS ADDENDUM INCLUDTHIS ADDENDUM INCLUDES:ES:ES:ES:

Civil Items 0 Pages

Structural Items 0 Pages

Architectural Items 2 Pages

Plumbing Items 0 Pages

Mechanical Items 0 Pages

Electrical Items 0 Pages

Technology Items 0 Pages

AND ALL AND ALL AND ALL AND ALL ATTACHED REVISED DRAWING REFERENCES IN THE ADDENDUMATTACHED REVISED DRAWING REFERENCES IN THE ADDENDUMATTACHED REVISED DRAWING REFERENCES IN THE ADDENDUMATTACHED REVISED DRAWING REFERENCES IN THE ADDENDUM

10-05-153-8-18

Project Name: La Vega High School Classroom Addition

Client: La Vega ISD

Location: Bellmead, Texas

Project Number: 1612-12-01

Architectural Items For

Addendum No. 1

Page 1 of 2

ARCHITECTURAL ITEMS FOR ADDENDUM NO. 1 NOTICE TO PROPOSERS:NOTICE TO PROPOSERS:NOTICE TO PROPOSERS:NOTICE TO PROPOSERS:

A. This Addendum shall be considered part of the contract documents for the above-mentioned project as though it had

been issued at the same time and incorporated integrally therewith. Where provisions of the following supplementary

data differ from those of the original contract documents, this Addendum shall govern and take precedence.

B. Proposers are hereby notified that they shall make any necessary adjustments in their estimate on account of this

Addendum. It will be construed that each Proposer’s proposal is submitted with full knowledge of all modifications and

supplemental data specified therein. Acknowledge receipt of this addendum in the space provided on the proposal

form. Failure to do so may subject Proposer to disqualification.

REFERENCE IS MADE TO THE DRAWINGS AND THE PROJECT MANUAL AS NOTED:

GENERAL:GENERAL:GENERAL:GENERAL:

AD No 1, Arch. Item 1: General, Site Logistics Plan, Exhibit 1,

For bidding purposes, a preferred site logistics plan is provided as part of this addendum. The awarded Contractor will be

responsible to coordinate exact locations of all elements with the Owner.

PROJECT MANUAL:PROJECT MANUAL:PROJECT MANUAL:PROJECT MANUAL:

AD No 1, Arch. Item 2: To the Project Manual, Sections as listed below, Part 2 – Products;

Products listed herein are considered acceptable for conformance with the design concept of the project and general

compliance with the information given in the contract documents. The manufacturer, supplier and installer are responsible for

meeting all requirements given in the contract documents unless specifically noted in the written approval.

1) To Section 07 5400, “Thermoplastic Membrane Roofing,”

Model 60 mil Mule-Hide PVC Membrane as manufactured by Mule-Hide Products

Model 60 mil Versico-PVC/VersiFlex as manufactured by Versico Roofing Systems

AD No 1, Arch. Item 3: To the Project Manual, Table of Contents,

1) Add Section 06 4116 Manufactured Wood-Veneer-Faced Casework in its entirety (6 pages).

2) Remove Section 06 4119 Manufactured Plastic-Laminate-Clad Casework in its entirety.

AD No 1, Arch. Item 4: To the Project Manual, Section 01 5000, “Temporary Facilities and Controls,”

1) Revise paragraph 1.03.A to read: The Contractor may use the Owner’s electrical power and water supply.

2) Remove paragraph 1.03.B.

AD No 1, Arch. Item 5: To the Project Manual, Section 06 4116, “Manufactured Wood-Veneer-Faced Casework,”

Add this section in its entirety.

AD No 1, Arch. Item 6: To the Project Manual, Section 06 4119, “Manufactured Plastic-Laminate-Clad Casework,”

Remove this section in its entirety.

10-05-153-8-18

Project Name: La Vega High School Classroom Addition

Client: La Vega ISD

Location: Bellmead, Texas

Project Number: 1612-12-01

Architectural Items For

Addendum No. 1

Page 2 of 2

DRAWINGS:DRAWINGS:DRAWINGS:DRAWINGS:

AD No 1, Arch. Item 7: To the Drawings, Sheet A8.1, “Casework Elevations,”

To General Casework Notes, Item 3, revise “Spec. Section 12 3220 – Arch. Cabinets” to “Spec. Section 06 4116 Manufactured

Wood-Veneer-Faced Casework.”

END OF END OF END OF END OF ARCHITECTURAL ARCHITECTURAL ARCHITECTURAL ARCHITECTURAL ADDENDUMADDENDUMADDENDUMADDENDUM

CLASSROOMADDITION

LAYDOWN AREAON OLDFENCED­INTENNIS COURTS

APPROXIMATELOCATION OFCONTRACTOR PARKING

LA VEGA HIGH SCHOOLCLASSROOM ADDITIONSITE LOGISTICS PLANNOT TO SCALE

1612­12­01ADDENDUM 1

EXHIBIT 1

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 1MANUFACTURED WOOD-VENEER-FACED CASEWORK

SECTION 06 4116MANUFACTURED WOOD-VENEER-FACED CASEWORK

PART 1 - GENERAL1.01 SECTION INCLUDES

A. Manufactured Wood Casework.B. Plastic Laminate Countertops.C. Cabinet hardware.D. Factory finishing.E. Preparation for installing utilities.

1.02 RELATED REQUIREMENTSA. Section 06 1000 - Rough Carpentry: Support framing, grounds, and concealed blocking.B. Section 08 8000 - Glazing: Glass for casework.

1.03 REFERENCE STANDARDSA. ANSI A135.4 - American National Standard for Basic Hardboard; 2012.B. ANSI A208.1 - American National Standard for Particleboard; 2009.C. ANSI A208.2 - American National Standard for Medium Density Fiberboard for Interior Use;

2009.D. AWI/AWMAC/WI (AWS) - Architectural Woodwork Standards; 2014.E. BHMA A156.9 - American National Standard for Cabinet Hardware; Builders Hardware

Manufacturers Association; 2010 (ANSI/BHMA A156.9).F. GSA CID A-A-1936 - Adhesive, Contact, Neoprene Rubber; Federal Specifications and

Standards; Revision A, 1996.G. HPVA HP-1 - American National Standard for Hardwood and Decorative Plywood; Hardwood

Plywood & Veneer Association; 2009 (ANSI/HPVA HP-1).H. NEMA LD 3 - High-Pressure Decorative Laminates; National Electrical Manufacturers

Association; 2005.I. NHLA G-101 - Rules for the Measurement & Inspection of Hardwood & Cypress; National

Hardwood Lumber Association; 2011.J. PS 1 - Structural Plywood; 2009.K. PS 20 - American Softwood Lumber Standard; National Institute of Standards and Technology

(Department of Commerce); 2010.1.04 ADMINISTRATIVE REQUIREMENTS

A. Preinstallation Meeting: Convene a preinstallation meeting not less than two weeks beforestarting work of this section; require attendance by all affected installers.

1.05 SUBMITTALSA. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Shop Drawings: Indicate materials, component profiles and elevations, assembly methods, joint

details, fastening methods, accessory listings, hardware location and schedule of finishes.1. Provide the information required by AWI/AWMAC/WI (AWS).

C. Product Data: Provide data for hardware accessories.D. Samples: Submit actual samples of architectural cabinet construction, minimum 12 inches

square, illustrating proposed cabinet, countertop, and shelf unit substrate and finish.E. Samples: Submit actual sample items of proposed pulls, hinges, shelf standards, and locksets,

demonstrating hardware design, quality, and finish.

10-05-153-8-18

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 2MANUFACTURED WOOD-VENEER-FACED CASEWORK

1.06 QUALITY ASSURANCEA. Perform work in accordance with AWI/AWMAC/WI (AWS) - Architectural Woodwork Standards,

Premium quality.B. Perform cabinet construction in accordance with AWI/AWMAC/WI (AWS) - Architectural

Woodwork Standards, Premium quality.C. Fabricator Qualifications: Company specializing in fabricating the products specified in this

section with minimum five years of documented experience.1. Company with at least one project in the past 5 years with value of woodwork within 20

percent of cost of woodwork for this Project.1.07 MOCK-UP

A. Provide mock-up of typical base cabinet, wall cabinet, countertop, and wardrobe cabinet,including hardware and finishes.

B. Accepted mock-up may remain as part of the Work. Notify Architect of their exact locations.1.08 DELIVERY, STORAGE, AND HANDLING

A. Deliver, store, and handle products to site under provisions of Section 01 6000 - ProductRequirements.

B. Protect units from moisture damage according to AWI/AWMAC/WI (AWS) and Section 01 7000- Execution and Closeout Requirements.

1.09 FIELD CONDITIONSA. During and after installation of custom cabinets, maintain temperature and humidity conditions

in building spaces at same levels planned for occupancy.1.10 WARRANTY

A. See Section 01 7800 - Closeout Submittals, for additional warranty requirements.B. Correct non-conforming work within a one year period after date of Substantial Completion.

PART 2 - PRODUCTS2.01 MANUFACTURERS

A. Acceptable fabricator shall be members in good standing of the Architectural WoodworkInstitute (AWI/AWMAC/WI).

2.02 DEFINITIONSA. Exposed portions of include surfaces visible when doors and drawers are closed. Bottoms of

cases more than 4'-0” above floor shall be considered as exposed. Visible members in opencases or behind full glass doors also shall be considered as exposed portions.

B. Semi-exposed portions of casework includes those members behind opaque doors or framedglass doors, such as shelves, dividers, interior face of ends, case back, drawer sides, backsand bottoms, and back face of doors.

C. Concealed portions of casework include sleepers, dust panels and other surfaces not usuallyvisible after installation. Tops of cases 6'-6” or more above floor shall be considered concealed.

2.03 LUMBER MATERIALSA. Hardwood Lumber: NHLA; Graded in accordance with AWI/AWMAC/WI (AWS) - Architectural

Woodwork Standards, Grade I/Premium; average moisture content of 6-8 percent; species asfollows:1. Exposed Surfaces: Species as scheduled in Section 01 6210.2. Semi-Exposed Surfaces: Species Same as "Exposed Surfaces".3. Concealed Surfaces: Species Birch.

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 3MANUFACTURED WOOD-VENEER-FACED CASEWORK

2.04 PANEL MATERIALSA. Veneer Faced Plywood Finish: HPVA HP-1; graded in accordance with AWI/AWMAC/WI

(AWS) - Architectural Woodwork Standards, core of veneer (wood plies); type of gluerecommended for specific application; thickness as required; face veneer as follows:1. Exposed Surfaces: Grade AA, As scheduled, plain sliced, book-matched.2. Semi-Exposed Surfaces: Grade A, As scheduled, plain sliced, book-matched.3. Concealed Surfaces: Grade B, Any species suitable for intended use, stain grade, plain

sliced.a. Provide 1" thick shelves at storage/book rooms.b. Provide 1" thick shelves when length is 36" or longer.

B. Particleboard: ANSI A208.1; medium density industrial type, minimum 45 lb./cu. ft. density,Grade 1-M-2 or better, as specified in AWI/AWMAC/WI (AWS), composed of wood chipsbonded with manufacturer's recommended adhesive under heat and pressure; sanded faces;thickness as required; use for components indicated on drawings.1. Use as backing for plastic laminate countertops unless otherwise indicated.

C. Medium Density Fiberboard (MDF): ANSI A208.2; type as specified in AWI/AWMAC/WI (AWS);composed of wood fibers pressure bonded with manufacturer's recommended adhesive to suitapplication; sanded faces; thickness as required.1. Use for door and drawer fronts with laminated wood veneer.2. For doors 6' high and greater use 1" thick material

D. Plywood for Non-Decorative Purposes: NIST PS 1, Interior rated adhesives, core of wood pliesfrom listed species unless otherwise indicated, thickness as indicated or as required byapplication.1. Semi-Exposed Surfaces: APA A-B Grade, plain-sliced scheduled face veneer.2. Concealed Surfaces: PS 1; APA B-B Grade, plain-sliced birch face veneer.

E. Hardboard: AHA A135.4; Pressed wood fiber with resin binder, Class 1 - Tempered, 1/4 inchthick, smooth one side for horizontal applications, smooth two sides (S2S) for verticalapplications; use for drawer bottoms, dust panels, vertical slot dividers, and other componentsindicated on drawings.

F. Hardwood Edgebanding: Use solid hardwood edgebanding matching species, color, grain, andgrade for exposed portions of cabinetry.

2.05 LAMINATE MATERIALSA. Manufacturers:

1. Formica Corporation: www.formica.com.2. Panolam Industries International, Inc\Nevamar: www.nevamar.com.3. Panolam Industries International, Inc\Pionite: www.pionite.com.4. Wilsonart International, Inc: www.wilsonart.com.5. Substitutions: See Section 01 6000 - Product Requirements.

B. High Pressure Decorative Laminate (HPDL): NEMA LD 3, types as recommended for specificapplications.1. Provide HPDL at all exposed surfaces.2. Provide Melamine (White color) at all semi-exposed and concealed surfaces.

C. Provide specific types as scheduled.1. Horizontal Surfaces: HGS, 0.048 inch nominal thickness, colors as scheduled, finish as

scheduled.2. Vertical Surfaces: VGS, 0.028 inch nominal thickness, through color, colors as scheduled,

finish as scheduled.3. Post-Formed Horizontal Surfaces: HGP, 0.039 inch nominal thickness, through color,

colors as scheduled, finish as scheduled.4. Post-Formed Vertical Surfaces: VGP, 0.028 inch nominal thickness, through color, colors

as scheduled, finish as scheduled.

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 4MANUFACTURED WOOD-VENEER-FACED CASEWORK

5. Flame Retardant Surfaces: HGF, 0.048 inch nominal thickness, through color, colors asscheduled, finish as scheduled.

6. Cabinet Liner: CLS, 0.020 inch nominal thickness, through color, colors as scheduled,finish as scheduled.

7. Laminate Backer: BKL, 0.020 inch nominal thickness, undecorated; for application toconcealed backside of panels faced with high pressure decorative laminate.

2.06 COUNTERTOPSA. Plastic Laminate Countertops for Manufactured Casework: 1-1/8" Particleboard, grade 1-M-2

for tops without sinks and phenolic particleboard, grade 1-M-3 for tops with sinks.2.07 ACCESSORIES

A. Adhesive: Type recommended by fabricator to suit application.B. Glass: Type as specified in Section 08 8000.C. Fasteners: Size and type to suit application.D. Bolts, Nuts, Washers, Lags, Pins, and Screws: Of size and type to suit application; galvanized

or chrome-plated finish in concealed locations and stainless steel or chrome-plated finish inexposed locations.

E. Concealed Joint Fasteners: Threaded steel.2.08 HARDWARE

A. Hardware: BHMA A156.9, types as indicated for quality grade specified.B. Cabinet Doors, each to have:

1. 1 Pr Hinges (RPC) 853 x US26D2. 1 Ea Pull(STLY)348315 x US26D3. 1 Ea Catch(STLY)41 x ALD4. Cabinet Doors located adjacent to a drywall partition shall have the following in addition to

the above hardware:5. 1 Ea Wall Bumper/Leaf(Rockwood)430 x US26D (w/Toggle-bolt Anchor)

C. Cabinet Drawers, each to have:1. 1 Ea. Pull(STLY)348315 x US26D2. 1 Pr Drawer Slides(K & V)#84003. (non-handed, 100#)

D. Cabinet Locks, each to have:1. 1 Ea. Marshall Best Security Corp. 725 Series Cabinet Deadlock with cylinder and core-

Verify Condition2. All locks shall be part of a master keying system. Refer to Section 08 7100 - Door

Hardware.3. Provide at all cabinets in nurse's clinic and counselor's offices. Provide three at each

reception area and where indicated on cabinet drawings. (Verify with Architect.)E. Teachers Wardrobe Cabinet, each to have:

1. 2-1/2 Pr Hinges (RPC) 844 x US26D2. 1 Ea. Marshall Best Security Corp. 725 Series Cabinet Deadlock with cylinder and core-

Verify Condition3. 1 ea Slide Bolt4. 2 ea Pulls (STLY) 348315xUSD26D5. 2 ea Roller Catches 590x626

F. Adjustable Shelves, each to have:1. 4 Standards (K & V)#2552. 4 Brackets/Shelf(K & V)#256

G. Pull-Out Keyboard Tray1. Each to have:(K & V)#5710

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 5MANUFACTURED WOOD-VENEER-FACED CASEWORK

H. Clothes Rod each to have:1. Rod(K & V)#770 52. Flange(K & V)#764 CHR

I. Coat Hooks:1. Ceiling Mounted: (IVES)#5802. Wall Mounted: (IVEVS)#582

J. Grommets (provide one at each knee space), each to be:1. Outwater#31-2" (Plastic) - Color Selected by Architect

a. Plastics Industries, Inc.K. Adjustable Shelves at Display Cases, each to have:

1. Standards (K & V)#872. Brackets/Shelf(K & V)#186

L. Casters:1. Swivel-type: 4-inch diameter wheels of soft or hard rubber and self-lube wheel bearing.

Swivel is double-level, hardened ball bearing. All metal surfaces are zinc-plated.2. Rigid-type: 4-inch wheels of soft or hard rubber, held in horns of formed steel, zinc plated.

Wheel spanner bushings. Load capacity is 225 pounds per caster. Brake available onboth swivel and rigid.

2.09 SHOP TREATMENT OF WOOD MATERIALSA. Provide UL approved identification on fire retardant treated material.B. Deliver fire retardant treated materials cut to required sizes. Minimize field cutting.

2.10 FABRICATIONA. Cabinet Style: Reveal overlay.B. Cabinet Doors and Drawer Fronts: Flush style.C. Drawer Construction Technique: Lock shoulder joints.D. Base Cabinets shall be 2'-0" deep unless noted otherwise on the drawings.E. Upper Wall Cabinets shall be 1'-2" deep unless noted otherwise on the drawings.F. Fabricate all drawers boxes using 1/2" inch, 9-ply laminated hardwood plywood. The top edges

of the drawer box sides and back are radiused. Drawer bottom is let in on four sides, andsecurely glued underneath with a continuous bead of glue around the perimeter of the drawerbottom. Additional bottom braces are used on drawers over 24" wide. All components haveone coat of clear waterproof sealer. Drawer boxes are screw-attached to separate drawerfronts.

G. Assembly: Shop assemble cabinets for delivery to site in units easily handled and to permitpassage through building openings.

H. Edging: Fit shelves, doors, and exposed edges with specified edging. Do not use more thanone piece for any single length.

I. Fitting: When necessary to cut and fit on site, provide materials with ample allowance forcutting. Provide matching trim for scribing and site cutting.

J. Plastic Laminate: Apply plastic laminate finish in full uninterrupted sheets consistent withmanufactured sizes. Fit corners and joints hairline; secure with concealed fasteners. Locatecounter butt joints minimum 2 feet from sink cut-outs.1. Apply laminate backing sheet to reverse side of plastic laminate finished surfaces.2. Cap exposed plastic laminate finish edges with material of same finish and pattern.

K. Matching Wood Grain: Comply with requirements of quality standard for specified Grade and asfollows:1. Provide center matched panels at each elevation.2. Provide sequence matching across each elevation.

La Vega ISD - La Vega High School Classroom Addition (1612-12-01)Bellmead, Texas

Huckabee 06 4116 - 6MANUFACTURED WOOD-VENEER-FACED CASEWORK

3. Carry figure of cabinet fronts to toe kicks.L. Mechanically fasten back splash to countertops with steel brackets at 16 inches on center.M. Provide cutouts for plumbing fixtures. Verify locations of cutouts from on-site dimensions. Seal

cut edges.2.11 FACTORY FINISHING

A. Sand work smooth and set exposed nails and screws.B. On items to receive transparent finishes, use wood filler matching or blending with surrounding

surfaces and of types recommended for applied finishes.C. Finish work in accordance with AWI/AWMAC/WI (AWS) Premium Quality.D. Stain exposed-to-view surfaces.E. Stain semi-exposed-to-view surfaces.F. Seal surfaces in contact with cementitious materials.G. Finish cabinets to match approved finish of factory-finished flush wood doors.H. The cabinet manufacturer shall obtain an approved door finish sample prior to beginning site

finishing of cabinets.I. Protect all hardware and other pre-finished materials from finish materials.

PART 3 - EXECUTION3.01 EXAMINATION

A. Verify adequacy of backing and support framing.B. Verify location and sizes of utility rough-in associated with work of this section.

3.02 INSTALLATIONA. Set and secure custom cabinets in place, assuring that they are rigid, plumb, and level.B. Use fixture attachments in concealed locations for wall mounted components.C. Use concealed joint fasteners to align and secure adjoining cabinet units and countertops.D. Where required, assemble units into one integral unit with joints flush, tight, and uniform. Align

similar adjoining doors and drawers to a tolerance of 1/16 inch.E. Carefully scribe casework abutting other components, with maximum gaps of 1/32 inch. Do not

use additional overlay trim for this purpose.F. Secure cabinets and counter bases to floor using appropriate angles and anchorages.G. Countersink anchorage devices at exposed locations. Conceal with solid wood plugs of species

to match surrounding wood; finish flush with surrounding surfaces.H. Seal between cabinets and walls with a clear permanently elastic sealing compound

recommended by manufacturer.I. Provide holes and cutouts as required for mechanical and electrical service fixtures. Use

permanently elastic sealing compound between top and splash as recommended bymanufacturer.

J. Do not install seams in countertops closer than 24" to sink.3.03 ADJUSTING

A. Test installed work for rigidity and ability to support loads.B. Adjust moving or operating parts to function smoothly and correctly.

3.04 CLEANINGA. Clean casework, counters, shelves, hardware, fittings, and fixtures.

END OF SECTION