Nikon Coolpix 4600 Repair Manual [ET]
-
Upload
alex-rivera -
Category
Documents
-
view
232 -
download
2
Transcript of Nikon Coolpix 4600 Repair Manual [ET]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
1/97
Copyright 2005 by Nikon Corporation.All Rights Reserved.
!!
Printed in Japan February 2005
VAA32001-R.3652.A
REPAIR MANUAL
VAA32001
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
2/97
VAA32001-R.3652.A
- E4600 -
CONTENTS
SPECIFICATIONS
DisassemblyWARNING
REAR COVER
DISASSEMBLY OF REAR COVER
Discharging of main condenser
FRONT COVER
DISASSEMBLY OF FRONT COVER
TRIPOD SOCKET
LCD
SPEAKER HOLDER
MONITOR HOLDER
SB UNIT
WIRE HOLDER
TB-1 PCB
CONDENSER HOLDER
LENS UNIT
Points to notice when disassembling / (re)assembling Lens unit
Tools required for FFD inspection and adjustment
FINDER UNIT
ZOOM MOTOR UNIT
DISASSEMBLY OF ZOOM MOTOR UNIT
CCD FRAME
BARRIER UNIT
FIXED BARREL
DISASSEMBLY OF FIXED BARREL
2ND LENS GROUP UNIT
SHUTTER
STRAIGHT BARREL
KEY BARRELTURN BARREL
1ST LENS GROUP UNIT
ASSEMBLY
1ST LENS GROUP UNIT
KEY BARRELTURN BARREL
STRAIGHT BARREL
SHUTTER
2ND LENS GROUP UNIT
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
3/97
VAA32001-R.3652.A
- E4600 -
ASSEMBLY OF FIXED BARREL
FIXED BARREL
CCD FRAME
ASSEMBLY OF ZOOM MOTOR UNIT
ZOOM MOTOR UNIT
FFD Inspection and adjustment (*FFD:Flange Focal Distance)
Preparation
FFD inspection and adjustment
FFD adjustment
BARRIER UNIT
Operation inspection
FINDER UNIT
Resolution inspection
LENS UNIT
CONDENSER HOLDER
TB-1 PCB
WIRE HOLDER
SB UNIT
MONITOR HOLDER
SPEAKER HOLDER
LCD
TRIPOD SOCKET
ASSEMBLY OF FRONT COVER
FRONT COVER
ASSEMBLY OF REAR COVER
REAR COVER
ADJUSTMENT
DISCRIPTION OF CIRCUIT
ELECTRICITY
OVERALL WIRING
CP1(DMA)CIRCUIT DIAGRAM
CP1(SYA) CIRCUIT DIAGRAM
CP1(CAA) CIRCUIT DIAGRAM
CP1(PWA) CIRCUIT DIAGRAM
CP1(STA) CIRCUIT DIAGRAM
ST1 CIRCUIT DIAGRAM
TB1 CIRCUIT DIAGRAM
OVERALL BLOCK DIAGRAM
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
4/97
VAA32001-R.3652.A
- E4600 -
CCD BLOCK DIAGRAM
LENS BLOCK DIAGRAM
ASIC BLOCK DIAGRAM
SYSTEM CONTROL BLOCK DIAGRAM
POWER BLOCK DIAGRAM
FUSE arrangement (CP1 PCB)
INSPECTION STANDARDS
Tool List
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
5/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
6/97
VAA32001-R.3652.A
- D2 E4600 -
REAR COVER
Remove the four screws [#102]. Remove the two screws [#103].
Open the USB cover [#033].
As pushing the top side of the rear cover unit [#030]
by your nger, perform unhooking.
Open the rear cover unit [#030] slowly backward and
remove the FPC.
Remove the USB cover [#033].
Rear cover unit [#030] Push.
USB cover [#033]
FPC
Rear cover unit [#030]
Screw [#102
]
Screw [#102]
Screw [#103]
USB cover [#033]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
7/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
8/97
VAA32001-R.3652.A
- D4 E4600 -
Discharging of main condenser
2K/5W
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
9/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
10/97
VAA32001-R.3652.A
- D6 E4600 -
DISASSEMBLY OF FRONT COVER
Remove the decoration top [#021].
Decoration top [#021]
Remove the two screws [#104].
Unhook the battery holder [#024].
Screw [#104]
Battery holder [#024]
Hook
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
11/97
VAA32001-R.3652.A
- D7 E4600 -
Remove the DC cover spring [#012]. Pull out the DC cover [#011].
Take off the spacer [#019] from the release button
unit.
In the gure below, the spacer is divided into three
pieces from the dotted line.
Remove the screw [#104].
Remove the release button unit [#020].
DC cover spring [#012]DC cover [#011]
Spacer [#019]
Screw [#104]
Release button unit [#020]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
12/97
VAA32001-R.3652.A
- D8 E4600 -
TRIPOD SOCKET
Perform unhooking and remove the tripod socket
[#201].
LCD
Lift up the LCD [#239] and unsolder the lead wires [red] and [white].
The LCD [#239] is adhered with the double-adhesive tape.
Remove the FPC.
Remove the LCD [#239].
SPEAKER HOLDER
Take off the spacer [#206]. Unsolder the lead wires [red] and [black].
As turning counterclockwise, remove the speaker
holder [#233].
Tripod socket [#201]
Lead wires [red] and [white]
FPC
LCD[#239]
Spacer [#206]
Hook
LCD[#239]
Speaker holder [#233]
Lead wire [red]Lead wire [black]
Float this section and
remove it as turning.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
13/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
14/97
VAA32001-R.3652.A
- D10 E4600 -
SB UNIT
Remove the spacer [#039]. Unsolder the lead wires [gray] and [white].
Unsolder the lead wire [black]. Unsolder the lead wire [pink].
Remove the screw [#104].
Float the ash unit [#219].
Spacer [#039]
Lead wires [gray] and [white]
Lead wire [black]Lead wire [pink]
Screw [#104]
Flash unit [#219]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
15/97
VAA32001-R.3652.A
- D11 E4600 -
WIRE HOLDER
Remove the screw [#102].
Remove the wire holder [#215].
TB-1 PCB
Perform unhooking and remove the TB-1 PCB [#216].
CONDENSER HOLDER
Take off the spacer [#224
].Remove the screw [#102].
Remove the condenser holder [#204].
Hook TB-1 PCB [#216]
Wire holder [#215]
Spacer [#224
]
Screw [#102]
Condenser holder [#204]
Screw [#102]
Wire holder [#215]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
16/97
VAA32001-R.3652.A
- D12 E4600 -
LENS UNIT
Remove the FPC.
Take off the spacer [#225].
Remove the two screws [#106].
The lens unit can be removed.
The spacer LPF [#209], the optical lter [#210] and the spacer [#211] can be removed.
Remove the solder xing the CCD. (Fig. 1)
Remove the CCD [#212], the lens mount [#213] and the spacer insulator [#214].
(Fig. 1)
FPC
Spacer [#225]
Solder
Screw [#106]
CCD [#212]
Spacer insulator [#214]
Lens mount [#213]
Spacer LPF [#209]
Optical lter [#210]
Spacer [#211]
Lens unit
Main PCB CP-1 [#218]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
17/97
VAA32001-R.3652.A
- D13 E4600 -
Points to notice when disassembling / (re)assembling
Lens unit
When the following parts are replaced for repairing the lens unit singularly, the lens unit checking tool is required for the
FFD inspection and adjustment. Therefore, at service facilities where there is no tool, do NOT make a replacement
1st lens group unit
2nd lens group unit
3rd lens group unit
Tools required for FFD inspection and adjustment
Note: When the operation check and adjustment of the lens unit are made for repairing the lens unit singularly,
the following tools are required.
Lens unit checking tool J61202
Connection cable for lens J61202F
PCI I/F board J61204
Connection cable for PC J61204A
Adjusting focus stand for APS J15327
Adapter for J15327 J15327A + J15327D
E4600/E5600 lens unit checking program J65072
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
18/97
VAA32001-R.3652.A
- D14 E4600 -
FINDER UNIT
Remove the three screws [#429]. Remove the nder unit [#405].
ZOOM MOTOR UNIT
Remove the solder of the motor at 2 places.
Remove the solder of the FPC at 4 places.
Remove the screw [#430].
Remove the zoom PI.
Remove the screw [#429].
Remove the screw [#431].
Remove the zoom motor unit.
Screw [#429]
Screw [#431]
Remove the solder.
Zoom motor unit
[#405]
Screw [#429]
Zoom PI
Screw [#430]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
19/97
VAA32001-R.3652.A
- D15 E4600 -
DISASSEMBLY OF ZOOM MOTOR UNIT
Pull out the gear shaft D [#419].
Remove the zoom gear E [#411].
Remove the screw [#429] and then remove the gear
cover [#403].
Remove the zoom gear D [#410] and the zoom gear C [#409].
Zoom gear E [#411]
Gear shaft D [#419]
Screw [#429]
Gear cover [#403]
Zoom gear D [#410]
Zoom gear C [#409]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
20/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
21/97
VAA32001-R.3652.A
- D17 E4600 -
BARRIER UNIT
Take off the name plate seal [#415]. Remove the barrier unit [#407] by turning
counterclockwise.
Insert tweezers into the clearance and turn the
barrier unit counterclockwise. It will be removed
easily.
Remove the barrier ring spring [#420].
Remove the barrier ring [#404] by turning clockwise.
Name plate seal [#415]
Barrier ring spring [#420]
Barrier ring [#404]
Clearance
Barrier unit [#407]
Clearance
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
22/97
VAA32001-R.3652.A
- D18 E4600 -
FIXED BARREL
Take off the FPC sheet [#423]. Push out the turn barrel [#401]. As taking out the
shutter FPC, remove the turn barrel [#402].
DISASSEMBLY OF FIXED BARREL
Pull out the gear shaft A [#413] and remove the zoom gear F [#412].
Pull out the gear shaft B [#418] and remove the nder gear A [#416].
Remove the light-shield ring [#424].
FPC sheet [#423]
Push out.
Turn barrel [#401]Shutter FPC
Gear shaft A [#413]
Gear shaft B [#418]
Zoom gear F [#412]
Finder gear A [#416]
Light-shield ring [#424]
Turn barrel [#402]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
23/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
24/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
25/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
26/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
27/97
VAA32001-R.3652.A
- A3 E4600 -
key barrel unit [#428].
2nd lens group unit [#426]
Notch
Groove
Convex section
Lever
Groove
Convex section
2ND LENS GROUP UNIT
Set the lever of the key barrel unit [#428] at the front side. Set the notch of the 2nd lens group unit [#426] at the left
side. Fit the convex sections to the grooves and set the 2nd lens group unit [#426] into the key barrel unit [#428].
ASSEMBLY OF FIXED BARREL
Set the light-shield ring [#424].
Make the stepped difference side of the nder gear A [#
416] face the CCD. Then, set the nder gear A [#
416] and
insert the gear shaft B [#418].
Set the zoom gear F [#412] and insert the gear shaft A [#413].
Apply the adhesive (EC-1368) to the gear shafts.
Gear shaft A [#413]
Gear shaft B [#418]
Zoom gear F [#412]
Light-shield ring [#424]
Finder gear A [#416]
EC-1368
EC-1368
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
28/97
VAA32001-R.3652.A
- A4 E4600 -
FIXED BARREL
Adhere the FPC sheet [#423].Insert the shutter FPC into the hole on the side of the
xed barrel [#402].
Fit the convex sections on the turn barrel [#401] to
the grooves on the xed barrel [#402]. Set the turn
barrel [#401] into the xed barrel [#402].
FPC sheet [#423]
Turn barrel [#401]
Shutter FPC
Fixed barrel [#402]
Groove
Convex section
Convex section
Groove
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
29/97
VAA32001-R.3652.A
- A5 E4600 -
CCD FRAME
Set the nder gear B [#417] into the lens barrel unit.
Then, install the lens barrel unit.
Tighten the four screws [#431]. Insert the FPC of the CCD frame into the boss.
Insert the shutter FPC into the boss.
Tighten the screw [#430].
Perform soldering.
Screw [#431]Screw [#431]
Lens barrel unit
Finder gear B [#417]
Screw [#430]
Solder
Shutter FPC
FPC of CCD frame
Boss
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
30/97
VAA32001-R.3652.A
- A6 E4600 -
ASSEMBLY OF ZOOM MOTOR UNIT
Set the zoom gear C [#409] and the zoom gear D
[#410].
Set the gear cover [#403] and tighten the screw
[#429].
Screw [#429]
Gear cover [#403]
Zoom gear D [#410]
Zoom gear C [#409]
Set the zoom gear E [#411] and insert the gear shaft
D [#419].
Zoom gear E [#411]
Gear shaft D [#419]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
31/97
VAA32001-R.3652.A
- A7 E4600 -
ZOOM MOTOR UNIT
Fit the zoom motor unit to the bosses on the CCD
frame and set it.
Tighten the screw [#430]. Solder the FPC at 4 places.
Solder the motor at 2 places.
Screw [#429]
Screw [#431
]
Perform soldering.
Zoom motor unit
Tighten the screw [#429].
Tighten the screw [#431].
Fold the FPC of the zoom PI as shown below and insert the zoom PI.
(1) (2) (3)
Zoom PI
Screw [#430]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
32/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
33/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
34/97
VAA32001-R.3652.A
- A10 E4600 -
Hold the lens-barrel unit lightly with a hand, and run the program for inspecting the lens unit.
On the main menu of the lens unit checking program, click on "FFD Check" icon, and measure the FFD value
according to instructions of the PC screen.
FFD adjustment
Make adjustment by turning the 1st lens group so that the FFD measured value may be within the standard as shown
below.
Note: If the lens-barrel unit is held too tightly,
the FFD value cannot be measured correctly.
Note: Refer to supplied user manuals of the lens unit
checking tool for how to run the program for
inspecting the lens unit.
Note: At the position where the color of vertical lines shifts from blue to red, read the
measurement value of the adjusting focus stand.
Zoom position FFD standard Measured value in relation to reference value (-2.16mm)
Wide-side 0.05mm -2.21 -2.11Tele-side 0.05mm -2.21 -2.11
Make adjustment at the Tele-side.
After the adjustment is nished, apply the screw lock to the 1st lens group unit.
1401B
1401B
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
35/97
VAA32001-R.3652.A
- A11 E4600 -
BARRIER UNIT
Insert the convex section A on the barrier ring [#404]
into the clockwise side of the convex section B in
the lens barrel. Then, set the barrier ring [#404] and
turn it counterclockwise.
Barrier ring [#404]
Convex section A
Convex section B
Set the barrier ring spring [#420].
Barrier ring spring [#420]
Apply the adhesive (EC-1368) to 4 places on the
back of the barrier unit [#407].
EC-1368
EC-1368
EC-1368
EC-1368
Set the barrier unit [#407] with its cav number at the
top side and turn it clockwise.
Barrier unit [#407]
Cav number
Cav number
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
36/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
37/97
VAA32001-R.3652.A
- A13 E4600 -
Resolution inspection
When dissembling and repairing the lens-barrel, be sure to check the following after assembling it into the camera body.
Resolution inspection
By shooting the high-denition resolution chart (J63079), conrm that the number of TV lines is within the
standard.
TV lines (standard): 1100 TV lines or more in the center; 700 TV lines or more at the periphery
(ref. The resolution is represented byTV lines, which are total number of black-and-white strips distin-
guishable on the TV screen.)
(a) To take pictures, set the camera as follows: Shooting-mode (AUTO), Image quality mode (High), Flash
mode (Flash cancel)
(b) Check the zoom position at WIDE, MIDDLE and TELE.The object distance: WIDE (approx. 0.5m), MIDDLE (approx. 0.98 m), and TELE (approx.1.6 m). Set
the chart fully screened in the LCD of the camera and x it on a tripod.
(c) Open the shot image by Photoshop, and conrm it by the magnied display, e.g. 100%, etc.
(d) Check if the resolution in the center and the 4 corners of the periphery is identiable in black and white at
the position circled in red as below.
In case the resolution is defective, it is necessary to replace the lens-barrel group unit with the new one.
High-denition resolution chart (J63079)
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
38/97
VAA32001-R.3652.A
- A14 E4600 -
LENS UNIT
Set the spacer LPF [#209] and the optical lter [#210] into the lens unit.
As taking care about its direction, set the spacer [#211] into the lens unit.
Set the spacer insulator [#214], the lens mount [#213] and the CCD [#212] and solder them to the main PCB CP-1
[#218]. (Fig. 1)
Tighten the two screws [#106].
Adhere the spacer [#225].
Set the FPC.
FPC
Spacer [#225]
(Fig. 1)
Perform
soldering.
Optical lter [#210]
Setting direction
Lens unit side CCD side
Screw [#106]
CCD [#212]
Spacer insulator [#214]
Lens mount [#213]
Spacer LPF [#209]
Spacer [#211]
Main PCB CP-1 [#218]
Lens unit
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
39/97
VAA32001-R.3652.A
- A15 E4600 -
CONDENSER HOLDER
Set the condenser holder [#204] and tighten the
screw [#102].
TB-1 PCB
Adhere the spacer [#224].
Spacer [#224]
Screw [#102]
Condenser holder [#204]
Spacer [#224]
Hook TB-1 PCB [#216]
Wire holder [#215]
Notch
Set the TB-1 PCB [#216] onto the hook of the wire holder [#215].
Pass the lead wire of the TB-1 PCB [#216] through the notch of the wire holder [#215].
WIRE HOLDER
Set the wire holder [#215] and tighten the screw
[#102
].
Screw [#102]
Wire holder [#215]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
40/97
VAA32001-R.3652.A
- A16 E4600 -
SB UNIT
Arrange the lead wires [pink] and [blue] as shown below.
As arranging the lead wire [blue] as shown below (Fig. 1), set the ash unit [#219] and tighten the screw [#104]. (Fig. 2)
(Fig.1)
(Fig.2)
Lead wire [blue]
Screw [#104]
Flash unit [#219]
Arrange the lead wire [pink] as shown below. Solder the lead wire [pink].
Lead wire [pink]
Lead wire [pink]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
41/97
VAA32001-R.3652.A
- A17 E4600 -
Solder the lead wires [gray] and [white].Solder the lead wire [black].
Lead wire [black]
Arrange the lead wires as shown below.
Adhere the spacer [#039].
Spacer [#039]
Lead wires [gray] and [white]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
42/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
43/97
VAA32001-R.3652.A
- A19 E4600 -
SPEAKER HOLDER
Adhere the spacer [#206].
Solder the lead wires [red] and [white].
Arrange the lead wires [red] and [white] as shown
below.
Spacer [#206]
Fit the center boss on the speaker holder [#233] into
the boss hole on the LCD holder [#231]. Then, turn
the speaker holder [#233] clockwise.
LCD
Set the FPC.
Solder the lead wires [red] and [white].
Arrange the lead wires [red] and [white] as shown below. Fold the FPC and set the LCD [#239].
Speaker holder
[#233]
Boss hole position
Lead wire [white] Lead wire [red]
Lead wires [white]
Lead wires [red]
FPC
LCD [#239]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
44/97
VAA32001-R.3652.A
- A20 E4600 -
TRIPOD SOCKET
Install the tripod socket [#201] by tting onto the
hook.
Install the release button unit [#020] by inserting its
convex section A into the notch B on the front cover
[#013].
Tighten the screw [#104].
ASSEMBLY OF FRONT COVER
Adhere the spacer [#019] of the release button unit
as shown below.
The spacer [#019] is divided into three pieces from
the dotted line in the gure.
Set the DC cover [#011].
DC cover [#011]
Set the DC cover spring [#012].
DC cover spring [#012]
Tripod socket [#201]
Hook
Convex section A
Notch B
Screw [#104]
Release button unit [#020]
Spacer [#019]
LCD [#239]
Set the convex section at
the top side.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
45/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
46/97
VAA32001-R.3652.A
- A22 E4600 -
FRONT COVER
Set the earth release [#026].
Tighten the two screws [#102].
Perform soldering.
Set the FPC.
Set the front cover [#013].
Front cover [#013]
Set the SD cover [#037].
Set the cover shaft [#009].
Set the earth shaft [#029].
Tighten the screw [#104].
ASSEMBLY OF REAR COVER
Screw [#102]
FPC
Perform soldering.
Earth release [#026]
Earth shaft [#029]
Screw [#104]
SD cover [#037]
Cover shaft [#009]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
47/97
VAA32001-R.3652.A
- A23 E4600 -
Fold the FPC as shown below and set it.Set the USB cover [#033].
REAR COVER
Tighten the two screws [#103].Set the rear cover unit [#030].
Rear cover unit [#030]
Tighten the four screws [#102].
USB cover [#033]
FPC
Rear cover unit [#030]
Screw [#103]
Screw [#102]
Screw [#102]
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
48/97
VAA32001-R.3652.A
- A24 E4600 -
1. Equipment
IBM compatible PC/AT AC adapter EH-62B USB cable ( UC-E6)
2. Servicing tools
Pattern box Color meter Luminance meter Siemens star chart Calibration software (J65071)
Adjustment collimator (J63090) or Adjustment rmware
3. Adjustment items and order
Adjustment after replacing the CP-1 PCB of RP
1. Writing of the initial image data
2. Firmware up
3. Lens adjustment
4. AWB adjustment
5. CCD white dot defect compensation
6. CCD black dot/white dot defect adjustment
7. USB storage information registration
Note) If replacing the lens, CCD, optical lter, it is necessary to perform the above 3-7 adjustments again. 4-6
adjustments should be made in the above order.
ADJUSTMENT
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
49/97
VAA32001-R.3652.A
- A25 E4600 -
4. Initial image data writing and Firmware upgrading
Device
AC adapter (EH-62B)Upgrading SD card X 1[How to create an upgrading SD card]
1) Format SD card on PC.
2) Create a folder named "rmware" in the root directory of the SD card.
3) Copy "rmware.bin" into the created folder.
4) Copy "nanddat.bin" into the root directory of the same SD card.
Note) When only rmware upgrading is performed without replacing CP-1 PCB, copying "nanddat.bin" into the SD card is
NOT necessary.
Procedure
Turn the camera OFF and connect the AC adapter.
Insert the upgrading SD card into camera.
Set the mode dial to "SETUP" and turn power ON.Highlight and select "Firmware version" to display the menu for data-writing of initial images. (Fig.1)
Write the data of initial images, and go on to upgrade the rmware.
Select "Yes", and press the decision button to carry out data-writing of initial images. (Fig.2)
Note: Do NOT turn power OFF during upgrading.
(Fig.1)
(Fig.2)
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
50/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
51/97
VAA32001-R.3652.A
- A27 E4600 -
5. Setup
1) System requirements
Windows 98 or Me, 2000, XP
IBM-compatible PC/AT with Pentium or higher processor
CD-ROM drive
3.5-inch 2HD diskette drive
USB port
40 MB or more RAM
Hard disk drive with 15 MB or more memory space
VGA or SVGA monitor with 256 or more color display
2) Installing calibration software
Insert the calibration software installation diskette into the diskette drive.
Open Explorer.
Copy "DscCalDi.exe, Camapi32.dll" folder of the oppy disk drive in any folder on the hard disk.
6. Installing USB driver
If the USB driver is necessary, install Nikon View via CD-ROM packed with the camera.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
52/97
VAA32001-R.3652.A
- A28 E4600 -
7. Pattern box
Before using the pattern box, turn its power on to carry out "Aging" approx. 30 minutes: the color temperature should
be 310020K by the adjustment with the color meter, and the luminance should be 90020cd/m2by the adjustment
with the luminance meter. When using the pattern box and for a while after its power turns off, the lamp and its
surroundings are subject to high temperatures, so care should be taken when handling.
Procedure for correcting Pattern Box
Note: Be sure to perform the aging correction.
1) Measure the measuring point (center of diffusion plate) with the Color Meter (J63081).
2) Adjust the pattern box so that the color temperature should be 3100 20K by using "VR for adjustment of the color
temperature".
3) Measure the center of the diffusion plate with the Luminance Meter BM-3000 (J63068).
4) Adjust the pattern box so that the luminance should be 900 20cd/m2by using "Knob for luminance adjustment".
5) Repeat from 1) to 4) So that the color temperature should be 3100 20k and luminance should be 900 20cd/m2
8. Adjustments required when parts are replaced
Lens Adj. AWB CCD
Defects
USB Firmware
up
Initial image
data
Lens Unit
Optical lter
CCD
CP-1
Adjustment is necessary. Adjustment is not necessary.
Power switch
VR for adjustment of
the color temperature
Knob for luminance
adjustment
Iris unit
Diffusion plate
Area to be measured
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
53/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
54/97
VAA32001-R.3652.A
- A30 E4600 -
11. Lens adjustment
For the lens adjustment, choose either the innity adjustment with the collimator or the 1.5-m adjustment with
the adjustment rmware. (However, in case of1.5-m adjustment, the focus may not be sharp at innity.)
11-1. Innity adjustment
[Preparations]
Turn the power switch of the adjustment collimator (C-DSC) J63090 to on.
Turn the power switch of the camera to on.
Siemens star chart
POWER switch of camera: ON
[Conditions]
Set the adjustment collimator and the camera (front surface of lens) at the nearest distance between them.
[How to]
Double-click on "DscCa1Di.exe".
Set the siemens star chart so that it comes center of the screen by checking through the viewnder.
Click "Focus", then "Yes".
Lens adjustment value will appear on the screen.
Judgment standard: xd0 = 0 55 , xd7 = 0 55 , xd13 = 0 55, xd19 = 0 55
Click "OK".
Result of adjustment
Adjustment collimator
(Siemens star chart built-in)
Camera
"Yes"
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
55/97
VAA32001-R.3652.A
- A31 E4600 -
11-2. 1.5-m Adjustment
Before performing the 1.5-m adjustment in this machine, write the adjustment rmware on the camera. After
adjustment, be sure to write the product rmware.
Procedure for setting Adjustment rmware
1) Save the adjustment rmware and the product rmware in any folder.
2) Start up "DscCa1Di.exe" and click on "Firmware" button on the main menu to write the adjustment rmware.
(If the camera is activated after completing writing the adjustment rmware, "SERVICE" is indicated in red letters
on LCD panel.)
3) Follow the instructions of the below [How-to].
4) Start "DscCaDi140" and click "Firmware" on the main menu to write the product rmware.
[Preparations]
Set the Siemens star chart.
Turn the power switch of the camera to on.
[Conditions]
The siemens star chart should be A3-size or larger (Copy and enlarge A4-size siemens chart included in the
service manual for the usage.)
Illumination over the object should be 400 lux 10%
Set the siemens star chart and the camera (front surface of lens) at 150 cm 3 cm distance between them.
[How-to]
Double click on "DscCa1Di.exe".
Set the siemens star chart so that it comes center of the screen by checking through the viewnder. Click "Focus" then "Yes".
Lens adjustment values will appear on the screen.
Judgment standard: xd0=055, xd7 = 055, xd13= 055 xd19 = 055
Click "OK".
Result of adjustment
"Yes"
150cm3cm
Siemens star chart
Camera
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
56/97
VAA32001-R.3652.A
- A32 E4600 -
12. AWB adjustment
[Preparations]
Pattern Box(Color temperature: 3100 20K, Luminance: 900 20cd/m2)
[Conditions]
Set the pattern box and camera (lens front) at "0cm" distance between them.
Note) Do not allow outside light to enter in.
[How to]
Double-click on "DscCa1Di.exe".
Click "AWB", then "Yes".
AWB adjustment values will appear on the screen.
Judgment standard: CHECK=128 1, 128 1, 130 40
Click "OK".
"Yes"
Result of adjustmentCamera
Pattern Box
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
57/97
VAA32001-R.3652.A
- A33 E4600 -
13. CCD white dot defect compensation
[Conditions]
With the lens shutter being closed, read the defect of CCD pixels. Then, make the correction data and rewrite the
data by the following procedure.
Correct the upper level of defective 2000 pixels from the brightest number of CCD pixels..
[How to]
Double-click on "DscCa1Di.exe".
Select "CCD Defect" from Test menu of Calibration Software and click the "OK". Refer to FIG-1.
After adjustment, the adjustment value will appear on the screen. Refer to FIG-2.
14. CCD black dot/white dot defect adjustment
[Conditions]
Fix the camera so that only the white part of the pattern box should be displayed on the screen.
(Do not allow outside light to enter in as much as possible.)
With the lens shutter being opend, read the defect (black dots) of CCD pixels. Then, make the correction data and
rewrite the data by the following procedure.
Correct the upper level of defective 256 pixels (black dots in bright place) of CCD pixels.
[How to]
Double-click on "DscCa1Di.exe".
Select "CCD Black" from Test menu of Calibration Software and click "OK". Refer to FIG-1.
After adjustment, the adjustment value will appear on the screen. Refer to FIG-3.
Pattern Box
Camera
CCD Defect
CCD Black
(FIG-3)
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
58/97
VAA32001-R.3652.A
- A34 E4600 -
15. USB storage information registration
USB storage data is important when the camera is connected to a computer via a USB connection.
If there are any errors in the USB storage data, or if it has not been saved, the USB specications will not be satised,
so always check and save the USB storage data.
[How to]
Connect the camera to a computer.
Double-click on the "DscCa1Di.exe".
Click on the "Get" button in the USB storage window and check the USB storage data.
VID: NIKON
PID: NIKON DSC E5600
Serial:
Rev. : 1.00
Check theSerialin the above USB storage data. If the displayed value is different from the serial number
printed on the base of the camera, enter the number on the base of the camera, and click the "Set" button.
Check VID and Rev. entries in the USB storage data. If any of them are different from the values in 3. above,
enter the details of3. and click the "Set" button.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
59/97
VAA32001-R.3652.A
- E1 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
60/97
VAA32001-R.3652.A
- E2 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
61/97
VAA32001-R.3652.A
- E3 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
62/97
VAA32001-R.3652.A
- E4 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
63/97
VAA32001-R.3652.A
- E5 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
64/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
65/97
VAA32001-R.3652.A
- E7 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
66/97
VAA32001-R.3652.A
- E8 E4600 -
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
67/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
68/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
69/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
70/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
71/97
VAA32001-R.3652.A
- E13 E4600 -
CP1(PWA)
CP1(PWA) CIRCUIT DIAGRAM
4.5V
Vf=3.580V
WT
RD
BAT-JW502
JW501
BAT+
GND
IN2-
IN1-
FB2
FB3
FB1
CNT7
CNT6
IN4-
FB4
IN3-
FB6
IN5-
FB5
PGND1-2
OUT1D-1
OUT1S-2
CNT1
CNT4
CNT5
CNT3
CS2
OUT1S-1
OUT1D-2
PVZ2A_A04
SW7CONT
OUT3S-2
OUT3D-2
PGND3-1
OUT3D-1
SW5
VS5
OUT3S-1
PGND3-2
GND2
VREG
IN6+
IN7-
FB7
RT
DTCT
VCC
IN6-
PGND2
OUT6
OUT2S-1
OUT2S-2
OUT4
OUT5
OUT7
SW6
VS6
PVCC
CS1
OUT2D-2
OUT2D-1
PGND1-1
M-GND
M-GND
M-GND
M-GND
M-GND
PP2-->5.49K
2125
CH4
CH5
CH7
CH2
CH1
CH6
FB
-8V(A)
+12V(A)
BOOST4.25V
UNREG
VDD
CE
H=1.2
POS-CAP
OM/ORTR16Z
H=3
GND
EXT
UNREG(ST)
VCONTVIN
LCDON
OM/ORLL98Z
H=2
OM/ORLL79Z
H=1.2
OM/ORTR25Z
GND
OFF
NP
IN
3.4V
VOUT
REG
3.25V(D)
3.45V(A)
H=0.85OM/ORVR26Z
VREG=1.5V
VREF=0.5V
OM/ORLLA0Z
OM/ORLLA0Z
OM/ORTR71Z
1.41V(D)
LCD_AN TO LCD BACK LIGHT
PA ON
BLON
LCD_CA
P ON
2.0A 32V
1608
16082A 32V
2A 32V1608
2.0A 32V
1608
2125
LDT565620T-**1 (H=2.0)
2125
3216
1608
2125
2125
2125
D
OXICAP(NOS)
D
S
G
2125
SG
NP04SB
1608
2125
2125
2125
OM/ORPTV008Z
LDT565620T-**1
D53LC
DB320C
L5009
L5010
F5002
F5005
F5004
F5001
C9601
C5030
R5035
R5036
T5001
R9604
C5035
R5046
Q9602
R5043
L5001
C5031
C9602
C5033
R9607
C5028
Q9601
R5033
R9606
R9605
C9604
C9603
R5034
R5032
D5007
C5032
C5029
L9601D9601
IC961
C5016
Q5006
R5040
R5037
Q5001
Q5003
R5038
C5034
L5004Q5004
C5022
L5003
D5001
C5003
C5002
C5001R5001
R5003
R5005
C5010
R5010
C5011
R5012
C5009
R5017
R5022
C5013
R5023
R5020
IC502C5020
C5023
L5005
D5003
C5021R
5018
R5019
C5017
R5014
R5015
R5009
VR501
C5006
C5005
R5007
C5004
IC501
C5007
C5008
D5006
Q5007
L5006
L5007
R5026
C5024
D5004
R5025
C5025
R5028
R5030Q5002 R5029
R5031
2A
2A
2A
2A
22;B
0.033;B
47K;1/16J
2.2K;1/16J
390K;1/16D
1;B
3K;1/16JDTC144EM
0;1/16Z
47;M
4.7;B
1;B
4.7;H
680K;1/16D
22;6.3B
FDC633N-NF
6.2
K;1/16D
130K;1/16D
15K;1/16D
22P;CH3
3;10-V
330;1/16D
150K;1/16D
HN2D01JE
1;B
1;B
10;M SD833-04(SC)
XC9104D095MP
UP03396
10K;1/16J
5.23K;1/16D
RSR025N03
120K;1/16D
1000P;B
3.3;NMCH5803-E
1;B
4.7;NSD833-04(SC)
1000P;B
1000P;B
0.01;B
5.6K;1/16J
4.7K;1/16J
3300P;B
13K;1/16J
1000P;B
4.3K;1/16J
0.1;B
3K;1/16J
10K;1/16D
330P;B
1.5K;1/16D
TK11134CS0.1;B
10;B
10;M
CUS01
1;B
47K;1/16J
12K;1/16D
0.047;B
CPH3409-E
22K;1/1
6D
3.3K;1/1
6D
30K;1/16D6.8K
1;B
1;B
2.2K;1/16J
560;1/16J
0.015;B FA7723R-H4-TE1
1;B
0.022;B
CUS01
DTC114EM
1.82K;1/16D
10;M
5.6;N
10K;1/16J
5.49K;1/16D
10;B
CUS01
10K;1/16D
1;B
150K;1/16J
4.7K;1/16J
MCH5803-E
10;1/16D
16V
16V
16V
6.3V
16V
1AV4L26B3450G
1AV4L26B3450G
F47K2R0C3LFND
F47K2R0C3LFND
F47K2R0C3LFND
F47K2R0C3LFND
1AV4L51B6421G
1AV4L2FM470MG
C10J330MABANG
1AV4L2MH3R3NG
DDCUS01-Q---P
QTK11134CS--J
1AV4L2JQ100MG
1AV4R3H7682NP
QFA7723R-H4-G
1AV4L2L5100MG
1AV4L2L55R6NG
-8.0V(A)
+12V(A)
UNREG
BOOST4.25V
TO STA
TO DMA(MAIN, LENS)
TO DMA(MAIN)
TO DMA(MAIN)& STA
TO DMA(MAIN)
TO SYA
TO DMA(LCD)
TO DMA(MAIN)
TO DMA(MAIN, LENS& LCD)
TO DMA(MAIN)
TO DMA(MAIN)
UNREG(ST)
LCDON
+12V(L)
+12V(B)
PAON2
VDD3
+3.45V(A)
VDD1.41
PAON
BLON
PON
17
8
5
6 2
4
3
6
5
43
2
1
5
43
2
1
54
3 2 1
51
5
43
2
1
5 4
321
5 6 5 5 5 4 5 3 5 2 5 1 5 0 4 9 4 8
5
4
3
2
1
4 7 4 6 4 5 4 4 4 3
42
41
40
39
38
43
2
232221201918171615
14
13
12
11
10
9
8
7
6 37
36
35
34
33
32
31
30
29
2827262524
5 4
321
D-D CONV.
SWITCHING MODULE
TO BATTERY
P1-69000/SX797-UNK
PWA !
!
!
!
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
72/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
73/97
VAA32001-R.3652.A
- E15 E4600 -
ST1
ST1 CIRCUIT DIAGRAM
JW551
BLACK
JW552OW/OYCE15
0Q1HZ
LPK
C5412
120u;300V
CEXAG580121AN
S1-69000/SX797-UNK
ST1
:
:
TO CP1(STA)
JM541, 542
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
74/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
75/97
VAA32001-R.3652.A
- E17 E4600 -
OVERALL BLOCK DIAGRAM
SDRAM
IC103
SD(0:31)128Mbit
16MbitFLASH(NOR)
FLASH(NAND)128Mbit
IC121
D(0:15)
FD(0:7)
A(1:20)
CKIN1
CKIN2
FSC4
IC111
CLOCK GENERATOR
28.63636MHz
X1101
CN143
SD CARD
FD(0:4)
LCD MONITOR
PADYOUT
LCDD(0:5)
LCDCLK
LCDTIMING
PULSEX5
IC152
VIDEO AMP
VOUT
CN110
USB/VIDEO
4MHzX 30 01 X 30 02
32.768KHz
MRST
ZTEST
PLLEN
SCK
SDI
SDO
SREQ
CN301
IC3018bit Micro Processor
LENS DRIVER
IC951
CN951
LENS
3
LENS BLOCK
Z3001
FSEN
FSMD1:2
FSIN1:2
PICTL
ZMIN1:2
ZPULSE1:2
ZRESETFPI
XSUB
CCDCK
CCDSD
CCDEN
SUBGT
XV(1:6)
TGVD,TGHD
ADCK
AD
(0:11)
XSG(1A,2A,1B,2B,3)
CCD BLOCK
IC101ASIC
5M Pixel
IC903
V. Driver
IC901IC905
CCD
CDS/AGC/AD-C
H. Driver
USBD+
USBD-
Ni-MH
CP1
LCD BACKLIGHT
LCD_AN
LCD_CA
DC/DC
CONVERTER
ELECTRONIC
FLASH
VDD
REGULATOR
IC302
LENSDC/DC
CONVERTER
IC961
CN302BACK SW UNIT
RELEASE UNIT
BL_
ON
PWA BLOCK
SYA BLOCK
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
76/97
VAA32001-R.3652.A
- E18 E4600 -
CCD
CCD BLOCK DIAGRAM
LENS
CCD
EF
XV2
XV3
XV5
XSG1A
XV6
+12V(A)
-8.0V(A)
MN39483PJJ
OD
PT
H1
RG
H2
VO
O_LPF
IC901
IC90
3
CH1,CH2,CH3,CH4,CH5
IV1,IV2,IV3,IV4,IV5,IV6
ISUB
Q9001
XV1
XSG2A
SUB
V.DRIVER
AN20101A
XSG1B
XSG3
SUBGT
IC905
CDS,A/D
C
AD9948
D2:11
31
32
33
AD0
AD9
ADCK
CCDCK
CCDSD
CCDEN
VCC
IC904
REG.
TK11130CS
3.0V+
3.45V(A)
VDD3
TO
CP1(DMA)
IC101ASIC
10
13
17
18
11
1~8
15
19
1,2,21,23,24
20,22,25,26,27,28
3
25
9
2:4.7:13
27
14,15,21
8
+12V(A)
+3.45V(A)
-8.0V
(A)
6,18
4,5
26, 24, 37, 6
TGVD
TGHD
34, 35
17,22
H.DRIVER
14SUBSW
16HL
XV4
XSUB
XSG2B
V1,V2,V3A,V3B,V4,V5A,V5B,V6
9-16
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
77/97
VAA32001-R.3652.A
- E19 E4600 -
LENS
LENS BLOCK DIAGRAM
FOCUS/
IR/SH DRIVER
OUT1
OUT4
UNREG
ZM.MOUTB
OUTADC 1-
DC 2+INB
INA
ZOOM DRIVER
LB8655TIC951
EN
MD1
MD2
2B
1B
2A
1AOUT2
OUT3
OUT5
OUT6
FC.M
SH.M
IR.M
ZPLUSE1
ZPLUSE2
PICTL(IC101 198pin)
VDD3
FOCUS_PI
CN951
UNIT LENS
ZPULSE1(IC101 213pin)
ZMIN1(IC101 209pin)
ZMIN2(IC101 208pin)
FSEN(IC101 203pin)
FSMD1(IC101 202pin)
FSMD2(IC101 201pin)
FSIN1(IC101 200pin)
FSIN2(IC101 199pin)
FPI(IC101 206pin)
SHUTTER+
SHUTTER-
IRIS+
IRIS-
19
18
6
7
20
17
8
9
11
10
3
5
13
ZOOM_PI
16
Q9509
IC961L9601, D9601Q9601, C9603
SW REG.
BOOST4.25V
ZRESET(IC101 210pin)
Q9501
Q9502ZPULSE2(IC101 212pin)
PIV1, 14
2
4
15
12
3
4
8
9
5
6
7
IN1
IN2
16
15
21
20
18
17
22
19
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
78/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
79/97
VAA32001-R.3652.A
- E21 E4600 -
SYSTEM CONTROL
SYSTEM CONTROL BLOCK DIAGRAM
33
34
35
28
4
3
29
9
7
6
10
38
20
42
30
46
39
37
26
2
17
12
24
5678
1 2 3 4
16
13
14
43
15
31
23
8
32
18
45
X3001
X300232KHZ
4MHz
41
XIN
XOUT
XCOUT
XCIN
VMONIT
CHG ON
PLLEN
LCD ON2
PA ON
P ON
VSS
LCD ON
SELF LED
VMONITCHG
BOOST4.25V
SREQ
P ON
PA ON
SPORTSNIGHTVIEW
OK
SCENE LANDSCAPEPORTRAIT
SET UP
PW_ON
LCD ON
1st
SI
21
LI
IC302BATTERYBACKUP
BAT
OFF
AL3.2
V
UNREG
VDD
RESET
ALWAYS3.2V
IC304RESET IC
4 3
1 2
OUT
VDD
VSS
BACK UP
SO
AUTO
2nd
MOVIE
SW3.2V
Q3001
TELE MENUDEL WIDE
--
PW_TEST
PLAY
RIGHTLEFT UP DOWNCN302
CN301
CN301
CN302
TEST
AVJACK
BACKUP_CTL
SCAN OUT0
SB. LED (R)
AF. LED (G)
IC3018bit MICRO
PROCESSORSCAN IN0
SCAN IN1
SCAN IN2
SCAN OUT1
SCAN OUT2
PW_LED
RESET
BAT OFF
BATTERY
SCAN IN3
SCAN IN4
AV REF ON
AVREF
SCAN OUT3
VDD
VDD
SCAN OUT4
SCK
36
ASIC TEST
1
22
MAIN RESET
CARD
27BEEP Q3005
47
25
COMREQ/BOT
USB_CONNECTTO DMA(MAIN)
TO DMA(MAIN)
TO TB1
PLLEN
LCDON2
SREQ
SDO
SDI
SCKZTEST
MRST
ZCARD
TO PWA+12V(B)
COMREQ
USBCNT
Z3001
Q3002
BOOST4.25V
44SELF LED
PA ON248PA ON2
UNREG
5
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
80/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
81/97
VAA32001-R.3652.A
- E23 E4600 -
XF111
BLK
D1703D1702
C1512
IC901
1AG4B10F20
00AB
C9008
D5405
D5408
D
1701
XF9019
33
F50042A
2AF5005
F5001
2A F5002
2A
SID
E-B
SX797_
CP1
CN171
JW502BAT-
JW501BAT+
RED
WT
LCD_CARD
LCD_AN
VDD1.41ZFWR
ZFRD
TRST
TCK
JSEL
SCNEN
TMS
TDO
TDI
GND
VDD3
C9035
VR501
IC541
5
43
1
6 1CN301
CN301
CN192
C
N193
IC103
IC121
IC904
5
4 3
1
IC101
CN302
CN302241
CN304
10
6
5 1
20 16
15
11
10
6
5
1
IC111
X1101
C1513IC152
6
43
1
IC905
403130
21 20 11 10
1
C90
17
IC901
28
23
22
15
14
9
8 1
18
10
9
1
IC951
IC951
CN191
20
1
CN951
CN95
1
IC903
CN17132 2
1
+
+1
10
1213
20
24
+
+
CL301
CL302C
L303
DISCHARGE
BOOT
GY
WTSIDE-B2000BB
SX797
TB1
IC103
IC101
IC121
CN192
CN193
IC901
IC905
Q5006
C1103
L1102
L1103
R1739
C1736
XF111
CN171
CN191
C1707
C1701
C1519
Q1736
Q
1735
R1735R1736
C1512
C1505C1515
R1503
R1509
C1504
R1502
Q1505IC152
R1501X
1101
D9001
R9508
C9032
R9012
C9018
R9008
D9003
D9004
C9017
C9505
C9502
C9504
CB951
R9501
C9503
IC951
R9505
C9506
C9501
R9014
C9027
R9010
XF901
L9002
C9003
CB904
C9034
R9017
C9036
C9035
C9030
C9006
CB902
CB903
C9023
C9012
C9013
R9015
R9016
R9003
C9025
C1706
C1705
R1701
R1702
C1513
C1708
C1734
D1701
D1702
D1703
C1702
Q9001
C9024
C3001
R3021
Q3005
R3022
R1734
C1751
R1733
R1526
L1302
CN304
VA306 VA307C1054 C
1056
RB107
R1054
C
1059
C1006 C1005
R1064
C1052
R
1055
R1053
R
1052
C1051
R1066
R1201RB144
R1404
RB143
R1410
R1104
C1104
R1111
C1102
C1105
R1102
C1114
L1101C1101
R1103
R1002
C1002
C1018
C1003
C1004
C1904
R1902
C1905
CN302
CN301
R5026
R5025
R5023
R5022
C5411
R5425
VA305 VA303 VA304
C5028
F5004
F5005
F5002
Q5003
F5001
C5033
L5002
R5036
C5031
R5034
R5033
C5030
R5032
Q5001
L5010 L5009
L5001
C5032
C5029
R5414
R5413
C5406
Q5407D5407
C5407
Q5405C
5414
C5416
R5420C
5415
IC541
R5401
Q5401
R5423
D5405D5408
D5007
RB104
C9028R9001
R9007
C9026
R9004
C9014
C9016
C9010
C9011
C9015
R9005
R9002
CB901
IC904
C9007
RB901
C9009
RB903
R1431
Q1431
Q1432 RB142
R1434
C1201
L1080
C1085
C1083
R1003
R1018
RB108
RB106
RB101
RB103
RB105 RB102
R1001
C1903
C1901
C1020C1007
L1001
C1086
C1084
C1009
R1047
R1046
C1019
R1005
L9003
RB902
R5035
R5043
R5009
L9004
L9001
C9005
R9006
R9013
R9011
VR501
R5017
R5016
C5012
C5013
C
1058
IC111
CN951
VA309
R9510
C9008
R1703
C1703 R
1403
RB146
C5037
C1709
C1303
C1304
D6001
F5001 F5002F5004 F5005
FUSE Function of FUSE Phenomenon when FUSE has blown out Rating
F5001Protection of the DC/DC converter and
the system computer circuitThe power is not turned on. 2A 32V
F5002 Protection of the DC/DC converter The power is not turned on. 2A 32VF5004 Protection of the lens circuit The power is not turned on. 2A 32VF5005 Protection of the speed light circuit The speed light is not charged. 2A 32V
FUSE arrangement (CP1 PCB)
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
82/97
VAA32001-R.3652.A
- E4600 -
The contents of inspection standards and tools for
E4600[1] Inspection standards ............................................................................................................................................R1 to R10
[2] Tools ....................................................................................................................................................................T1 to T5
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
83/97
VAA32001-R.3652.A
- R1 E4600 -
Item Criteria Applied tool(s)
External view
Gap/Difference in
height
Outside and inside
status
General components
Gap:0
.3
mm or lessDifference in height: 0.15mm or less
When the battery case is opened/closed:
Gap in its periphery: 0.3mm or less
Gap in the bottom: 0.5mm or less
Difference between right and left: 0.2mm or less
Stepped difference: 0.5mm or less
There must be no noticeable damage, stain, sink mark, welded
mark, unevenness, crack or oil exudation.
When pushing the main body, noticeable noise must not be heard.
(Observe and check it by naked eyes under fluorescent lamp and
natural sunshine.)
Visual observation
Operation/Operability
Operation
Operability of buttons
Mode dial
Operation touch
Each cover
While operating, any irregularities or irregular noise shall not be
required.
(Check it by shaking the camera while operating. Lightly hit the
camera onto the Linoleum-laid desk while operating.)
No cave-ins of the buttons shall be required.
Operator must feel "click" on each button.
"Click" must occur when or after a switch is ON.
(Check it while operating normally.)
When clicking, normal touch shall be required. Any outstanding
"caught-in-mechanism" touch or "rubbed-in-mechanism" touch or
play shall not be required.
(Check and observe the condition through normal operation.)
When operating a lever or knob by hand, any irregular conditions
shall not be required.
(Operate the camera in the actual photography procedure and check
the operation touch.)
When closed, there must not be an extreme play.
Each cover can be opened/closed without any outstanding
"caught-in-mechanism" touch or "rubbed-in-mechanism" touch or
abnormal noise.
(Open and close each cover and check it.)
Primary battery/
Secondary battery
INSPECTION STANDARDS
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
84/97
VAA32001-R.3652.A
- R2 E4600 -
Item Criteria Applied tool(s)
Monitor
Shooting image Inclined degree of image shall be 0.5 degree or less.
PC monitor and print output(Output will be evaluated while the display range boundary of LCD
unit is regarded as standard when the through-the-monitor image is
made.)
Photoshop
Printer
Lens capacity
Focal length
Open aperture F No.
Peripheral light reduc-
tion
Ghost/Flare
Point light source
Surface light source
Distortion
Dust in a picture
Wide-end position (Compelling )
5.7 mm + 7.1%
- 1.1%
Tele-end position (Compelling )
17.1 mm + 0.9%
- 6.9%
Wide-end position (Compelling )
F2.9 + 5.8%
- 2.3%
Tele-end position (Compelling )
F4.9 + 10.6%
+ 2.1%
Against the picture center, the luminance of the nearest peripheral
area must be 35% or more.
Against the picture center, the luminance at 70% of the image
height must be 55% or more.
There must not be an outstanding ghost/flare.
There must not be an outstanding flare at the center.
There must not be an outstanding deformation.
There must not be an outstanding dust in a picture.
When the picture center (within the circle whose diameter is 80%
of the short side) is Zone I and its outside is Zone II, the light
reduction against the periphery must be as follows :
a bZone I 4 or less 0
Zone II 10 or less 2 or less
a :1
.5
% or lessb : More than 1.5% and less than 3.0%
Focal length
measuring instrument
Lens drive tool
Visual observation
Photoshop
CRT monitor
PC
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
85/97
VAA32001-R.3652.A
- R3 E4600 -
Item Criteria Applied tool(s)
Lens barrel
Zoom / Focus There must not be an abnormal action (for example, the unit oper-
ates one-sidedly or its operation is not smooth or it is caught).(As changing the camera's posture, check it in all the directions.)
Visual observation
AF
Distance measurement
operation
Shortest photograph
distance
Normal
Macro
In the case of normal AF: Focus must be fit at the picture center.
In the case of the out-of-focus object: Focus must be fit at the 2m
point.
In the case of the scene mode: Focus must be fit in the selected
area.
Focus must be fit at the following distance.
30cm (in whole area)
12cm(Z00) 7.8cm(Z14) 4cm(Z04) 10 .5 cmZ19
4.7cm(Z09)
Visual observation
Tape measure
EIAJ chart
Siemens chart
Shooting with a speed
light
Light adjustment accu-
racy
Guide No. FULL
(ISO100m)
Recycling time
Wrong flash
Tele-end: 0.4 ~ 2.0m
Wide-end: 0.4 ~ 3.3m
Macro-wide-end0.43.4
In the above range,0.5 Ev or less
(Photography mode: AUTO ,Speed light: Compelling flash)
6.8 0.4 EV
(Charge for10 seconds with the new primarybattery and perform
measurement within 1 second.)
Within 8 seconds
Perform charging with a new primary battery for
10seconds and
carry out full flashing within 1 second. Then, measure the time
taken until the speed light LED finishes blinking while pressing
lightly the shutter release button (including the ON/OFF time of
the monitor LCD).
Wrong flash must not occur.
(Check by loading/unloading a battery, giving a light shock and
operating mode buttons except S2.)
Standard reection
plate
Flash meter
New battery
Measurement
rmware
Stop watch
New battery
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
86/97
VAA32001-R.3652.A
- R4 E4600 -
Item Criteria Applied tool(s)
Quality of image
Resolution in AF The resolution must be in compliance with the following values in
all the postures of the EIA J chart evaluation.
Center horizontal/vertical: 1100 TV pcs.
Periphery horizontal/vertical: 700 TV pcs.
Center horizontal/vertical: 1100 TV pcs.
Periphery horizontal/vertical: 700 TV pcs.
Center horizontal/vertical: 700 TV pcs.
Periphery horizontal/vertical: 450 TV pcs.
Center horizontal/vertical: 450 TV pcs.
Periphery horizontal/vertical: 300 TV pcs.
Center horizontal/vertical: 250 TV pcs.
Periphery horizontal/vertical: 150 TV pcs.
(The whole zoom area)
Center horizontal/vertical: 1100 TV pcs.
(The whole zoom area)
Center horizontal/vertical: 900 TV pcs.
Take a picture on condition that aperture is "open" in the AUTO
mode and image quality priority mode.
Equip the 5100K viewer with the chart with WIDE-end, MIDDLE
(Z08), TELE-end and the distance of0.3m or more and shoot an
object in the full range of angle of view.
Then, open the recorded image data file through Photoshop and
check the resolution visually.
Check each posture and the difference of zoom reciprocation.
Take a picture in each quality mode.
Measure the TV resolution pieces at center.
EIAJ chart
PhotoshopSiemens chart
In the case ofMacro
Center horizontal/vertical: 900 TV pcs.
Check at near distance (W12cm, M (Z08) 4cm, T10.5cm).
Take a picture at the high image quality mode.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
87/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
88/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
89/97
VAA32001-R.3652.A
- R7 E4600 -
Item Criteria Applied tool(s)
Finder
View / Image
Visual field frame/
frame line
Shading
Operation
Dust, fluff and damage
There must be no blur, distortion, ghost, halation or other out-
standing troubles in contrast, gradation, etc.
Blur or difference in thickness must be within the proper range to
operate the stamped line and visual field frame.
You can check the whole finder visual field.
The finder must be activated smoothly in a link operation with the
lens barrel zooming action.
The position and quantity must be as follows
Zone
Size A B C
Less than 10m 0 pc 2pcs or less 3pcs or less
10~20m 0 pc 0 pc 1pcs or less
More than 20 m 0 pc 0 pc 0 pcs
Visual observation
Visual observation
Visual observation
b/6
b/2
b
a/8 a/2 aAB
C
Total:3pcs or less
Interval:Less than b/2
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
90/97
VAA32001-R.3652.A
- R8 E4600 -
Item Criteria Applied tool(s)
LCD and others
Monitor LCD View
Visual eld ratio
Bright pixels or dim
pixels on LCD
Self-timer
Operation time:
LED blinks/lights
The reproduction of W, B and RGB must not be interfered.
The monitor LCD must comply with the SY monitor LCD perfor-mance standard.
There must be no shading in the LCD display range.
The inclination of the image and the monitor frame must be
0.75 or less.
The vertical difference and horizontal difference of the black belt
width in the image periphery must be within 0.3mm.
Through-the-monitor image: 96 to 100%
Play-back image: 98 to 100%
Perform reproduction for each single color of R, G, B and white
and check visually.
1 2 1
1
Zone A 2
Zone B 1
Zone Bright pixel Dim pixel
A 16
B 3
Total 4 6
Bright pixels: Visible normally through 5% ND filter
Dim pixels: Visible normally (Standard: Within the above
quantity)
101 second
Blinks 9 times and lights for1 second.
(Measure the time until release is done since the shutter release
button was lightly pressed.)
Visual observation
Visual observation
Visual observation
Visual observation
Stop watch
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
91/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
92/97
VAA32001-R.3652.A
- R10 E4600 -
Item Criteria Applied tool(s)
Electric characteristics
When voltage
increases(Alkaline battery)
Level 1
Level 2
(Ni-MH)
Level 1
Level 2
(Li battery)
Level 1
Level 2
2.25 0.1V
2.1 0.1V
2.45 0.1V
2.1 0.1V
2.6 0.1V
2.1 0.1V
Connect the constant-voltage power supply to the dummy battery
pack and check the voltage at Level 3 ("no battery capacity"
indication). Then, turn off the power, increase the voltage by
0.1V and change the power switch from OFF to ON. The voltage
is under the following conditions now. Measure the voltage.
(When changing the voltage, turn off the power.)
Level 1 : The battery mark is turned off on the monitor LCD.
Level 2 : The battery "half" mark lights on the monitor LCD.
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
93/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
94/97
VAA32001-R.3652.A
- T2 E4600 -
Tool No.
Name
Remarks
J65071
Calibration Software
(E995,E775,E885
E5000, E2500, E4500
E5700, E4300, E3500
E3100, E2100, E5400
E3700, E3200, E2200
E8700, E4100, E4600
E5600)
Common(E995,E775,E885
E5000, E2500, E4500
E5700, E4300, E3500E3100, E2100, E5400
E3700, E3200, E2200
E8700, E4100, E4600
E5600)
J63090 (C-DSC)
Collimat
Common
Attached in
Service Manual
Common
J63079 ITE (4:3 )
ITE HIGH RESOLUTION CHART (4:3 REFLECT TYPE)
Common
New tool
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
95/97
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
96/97
VAA32001-R.3652.A
- T4 E4600 -
Tool No.
Name
Remarks
J15327 FFD
Adjusting focus stand for APS
FFD
For FFD inspection and
adjustment
J15327A FFD
Adapter for J15327A
FFD
For FFD inspection and
adjustment
J15327D FFD
Adapter for J15327D
FFD
For FFD inspection and
adjustment
J65072 E4600/E5600
E4600/E5600 lens unit checking program
FFD
For FFD inspection and
adjustment
New tool
-
7/27/2019 Nikon Coolpix 4600 Repair Manual [ET]
97/97
VAA32001-R.3652.A