Nexus 5000 Errors

Send document comments to nexus5k -doc feedback@c i sco .comAmericas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000

800 553-NETS (6387)Fax: 408 527-0883

Nexus 5000 Series NX-OS System Message ReferenceJune 14, 2011

Text Part Number: OL-25078-01

Send document comments to nexus5k -doc feedback@c i sco .comTHE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Nexus 5000 Series NX-OS System Message Reference 2011 Cisco Systems, Inc. All rights reserved.

OL-25078-01

ACLMGR-4 2ACLMGR-6 2

ACLQOS Messages ACLQOS-SLOT#ACLQOS-SLOT#-5

-6

-7Send document comments to nexus5k -doc feedback@c i sco .com

C O N T E N T S

Preface xvii

Audience xvii

Organization xvii

Document Conventions ii-xvii

Obtaining Documentation and Submitting a Service Request xviii

C H A P T E R 1 Introduction to System Messages for Cisco NX-OS 1-1

System Log Message Format 1-1Syslog Format On a Resident Switch 1-1Syslog Format On a Remote-Logging Server 1-3

Capturing System Messages and History 1-5Saving the System Messages Log 1-5Logging System Messages to a Syslog Server 1-5

C H A P T E R 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 Family 2-1AAA Messages 2-1

AAA-1 2-1AAA-2 2-1AAA-3 2-2AAA-6 2-2

AAM Messages 2-2AAM-2 2-2AAM-3 2-2

ACLLOG Messages 2-3ACLLOG-4 2-3ACLLOG-6 2-3

ACLMGR Messages 2-3ACLMGR-2 2-4ACLMGR-3 2iNexus 5000 Series NX-OS System Message Reference

2-8-2 2-8-3 2-8

ContentsSend document comments to nexus5k -doc feedback@c i sco .com

ACLQOS-SLOT#-4 2-9ACLQOS-SLOT#-5 2-10

ACLTCAM Messages 2-10ACLTCAM-2 2-10ACLTCAM-3 2-14ACLTCAM-4 2-14ACLTCAM-6 2-15

ACL Messages 2-15ACL-2 2-15ACL-4 2-16ACL-5 2-17ACL-6 2-17

ASCII-CFG Messages 2-18ASCII-CFG-2 2-19ASCII-CFG-3 2-20ASCII-CFG-6 2-20

ASSOC MGR Messages 2-21ASSOC MGR-0 2-21ASSOC_MGR-1 2-22ASSOC_MGR-2 2-22ASSOC_MGR-3 2-22ASSOC_MGR-4 2-22ASSOC_MGR-5 2-22ASSOC_MGR-6 2-23ASSOC_MGR-7 2-24

BFDC Messages 2-24BFDC-SLOT#-2 2-24

BFD Messages 2-25BFD-3 2-25BFD-4 2-25BFD-5 2-26BFD-6 2-26

BIOS DAEMON Messages 2-28BIOS DAEMON-2 2-28BIOS_DAEMON-5 2-29BIOS_DAEMON-SLOT#-2 2-29BIOS_DAEMON-SLOT#-5 2-29

BOOTUP TEST Messages 2-29BOOTUP TEST-2 2-30iiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

BOOTVAR Messages 2-30


BOOTVAR-2 2-30BOOTVAR-3 2-31BOOTVAR-5 2-32BOOTVAR-6 2-33

CALLHOME Messages 2-34CALLHOME-2 2-34CALLHOME-3 2-35CALLHOME-6 2-36

CDP Messages 2-36CDP-2 2-36CDP-3 2-36CDP-4 2-37CDP-5 2-38CDP-6 2-38

CERT_ENROLL Messages 2-39CERT_ENROLL-2 2-39CERT_ENROLL-3 2-40CERT_ENROLL-6 2-40

CFS Messages 2-40CFS-2 2-40CFS-3 2-42CFS-4 2-44CFS-6 2-44

CIMSRVPROV Messages 2-46CIMSRVPROV-2 2-46CIMSRVPROV-3 2-47CIMSRVPROV-6 2-48

CLIS Messages 2-48CLIS-5 2-48

CLOUD Messages 2-48CLOUD-2 2-48CLOUD-3 2-49CLOUD-6 2-49

CLUSTER Messages 2-49CLUSTER-2 2-50

CMPPROXY Messages 2-50CMPPROXY-2 2-50CMPPROXY-5 2-51CMPPROXY-6 2-51iiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

COPP Messages 2-51


COPP-2 2-51COPP-3 2-52COPP-5 2-52COPP-6 2-53

CORE-DMON Messages 2-53CORE-DMON-2 2-53CORE-DMON-3 2-53

CREDITMON Messages 2-54CREDITMON-SLOT#-2 2-54

CTS Messages 2-54CTS-2 2-54CTS-3 2-57CTS-5 2-57CTS-6 2-57

DCEFIB Messages 2-57DCEFIB-SLOT#-0 2-58DCEFIB-SLOT#-2 2-58DCEFIB-SLOT#-6 2-58

DEBUGPROXY Messages 2-59DEBUGPROXY-6 2-59

DEVICE-ALIAS Messages 2-59DEVICE-ALIAS-2 2-59DEVICE-ALIAS-3 2-60DEVICE-ALIAS-6 2-63

DEVICE_TEST Messages 2-65DEVICE_TEST-2 2-65DEVICE_TEST-3 2-67DEVICE_TEST-4 2-68DEVICE_TEST-5 2-68DEVICE_TEST-6 2-69

DEV_LOG Messages 2-69DEV_LOG-3 2-69DEV_LOG-SLOT#-4 2-69

DFTM Messages 2-69DFTM-SLOT#-2 2-69DFTM-SLOT#-3 2-70

DHCP_SNOOP Messages 2-71DHCP_SNOOP-2 2-71DHCP_SNOOP-3 2-72ivNexus 5000 Series NX-OS System Message Reference

OL-25078-01

DHCP_SNOOP-4 2-74


DHCP_SNOOP-6 2-75DIAGCLIENT Messages 2-77

DIAGCLIENT-2 2-78DIAGCLIENT-3 2-78DIAGCLIENT-4 2-79DIAGCLIENT-5 2-79

DIAGMGR Messages 2-80DIAGMGR-2 2-80DIAGMGR-3 2-81DIAGMGR-4 2-81DIAGMGR-5 2-82DIAGMGR-6 2-83

DIAG_PORT_LB Messages 2-83DIAG_PORT_LB-2 2-84DIAG_PORT_LB-3 2-85DIAG_PORT_LB-4 2-88DIAG_PORT_LB-5 2-88

DMM Messages 2-88DMM-SLOT#-5 2-88

DOT1X Messages 2-90DOT1X-2 2-91DOT1X-3 2-91DOT1X-4 2-92DOT1X-5 2-93

DPP_DEBUG Messages 2-94DPP_DEBUG-2 2-94

DPVM Messages 2-95DPVM-2 2-95DPVM-3 2-95DPVM-4 2-96DPVM-6 2-96

DRAP Messages 2-96DRAP-4 2-97DRAP-6 2-97

DSTATS Messages 2-97DSTATS-2 2-98DSTATS-3 2-98

ELTMC Messages 2-99ELTMC-SLOT#-2 2-100vNexus 5000 Series NX-OS System Message Reference

OL-25078-01

ELTM Messages 2-101


ELTM-2 2-102ELTM-6 2-102

EOU Messages 2-103EOU-2 2-103EOU-5 2-103EOU-6 2-103EOU-7 2-105

EPLD_UPGRADE Messages 2-105EPLD_UPGRADE-2 2-106

EPP Messages 2-106EPP-5 2-106

ETH-PORT-SEC Messages 2-106ETH-PORT-SEC-3 2-106ETH-PORT-SEC-5 2-108

ETHPORT Messages 2-108ETHPORT-2 2-109ETHPORT-3 2-110ETHPORT-4 2-111ETHPORT-5 2-112

ETH_PORT_CHANNEL Messages 2-122ETH_PORT_CHANNEL-1 2-122ETH_PORT_CHANNEL-2 2-123ETH_PORT_CHANNEL-3 2-123ETH_PORT_CHANNEL-4 2-126ETH_PORT_CHANNEL-5 2-126ETH_PORT_CHANNEL-6 2-129ETH_PORT_CHANNEL-7 2-129

EUREKA_USD Messages 2-130EUREKA_USD-3 2-130

EVMC Messages 2-130EVMC-3 2-130EVMC-4 2-130EVMC-5 2-131

EVMS Messages 2-131EVMS-2 2-131EVMS-4 2-132

EXCEPTIONLOG Messages 2-132EXCEPTIONLOG-SLOT#-2 2-132

FC-TUNNEL Messages 2-132viNexus 5000 Series NX-OS System Message Reference

OL-25078-01

FC-TUNNEL-3 2-132


FC-TUNNEL-5 2-134FCC_LC Messages 2-134

FCC_LC-2 2-135FCC_LC-5 2-135FCC_LC-6 2-136

FCC Messages 2-136FCC-2 2-136FCC-5 2-136FCC-6 2-137

FCDDH Messages 2-137FCDDH-SLOT#-3 2-138FCDDH-SLOT#-4 2-138FCDDH-SLOT#-5 2-138

FCDD Messages 2-138FCDD-SLOT#-3 2-138FCDD-SLOT#-4 2-139FCDD-SLOT#-5 2-139FCDD-SLOT#-7 2-140

FCDOMAIN Messages 2-140FCDOMAIN-2 2-140FCDOMAIN-3 2-143FCDOMAIN-4 2-145FCDOMAIN-5 2-146FCDOMAIN-6 2-147FCDOMAIN-3 2-153

FCD Messages 2-155FCD-7 2-155

FCFWD Messages 2-156FCFWD-3 2-156FCFWD-4 2-156FCFWD-6 2-156

FCNS Messages 2-156FCNS-2 2-157FCNS-3 2-157FCNS-4 2-158FCNS-6 2-158

FCOE_MGR Messages 2-159FCOE_MGR-2 2-159FCOE_MGR-5 2-159viiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

FCSP-MGR Messages 2-160


FCSP-MGR-2 2-160FCS Messages 2-162

FCS-2 2-162FCS-3 2-163FCS-4 2-164FCS-5 2-164FCS-6 2-165

FDMI Messages 2-165FDMI-2 2-165FDMI-3 2-166FDMI-4 2-167FDMI-6 2-167

FEATURE-MGR Messages 2-167FEATURE-MGR-2 2-167

FEX Messages 2-168FEX-2 2-168FEX-5 2-169

FICON Messages 2-170FICON-2 2-170FICON-3 2-170FICON-5 2-172FICON-6 2-172

FLOGI Messages 2-173FLOGI-1 2-173FLOGI-2 2-174FLOGI-4 2-174FLOGI-5 2-174

FS-DAEMON Messages 2-175FS-DAEMON-2 2-175FS-DAEMON-6 2-175

FSCM Messages 2-175FSCM-2 2-175FSPF-3 2-176FSPF-4 2-178FSPF-5 2-179FSPF-6 2-179FSPF-7 2-181

FWM Messages 2-181FWM-0 2-181viiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

FWM-1 2-181


FWM-2 2-182FWM-3 2-184FWM-4 2-184FWM-6 2-185

GLBP Messages 2-185GLBP-2 2-185GLBP-3 2-186GLBP-4 2-187GLBP-5 2-189

HSRP_ENGINE Messages 2-191HSRP_ENGINE-3 2-191HSRP_ENGINE-4 2-192HSRP_ENGINE-6 2-193

IKE Messages 2-195IKE-3 2-195IKE-4 2-197IKE-6 2-198

ILC-SPAN Messages 2-198ILC-SPAN-3 2-198

ILC_HELPER Messages 2-198ILC_HELPER-2 2-198ILC_HELPER-3 2-198ILC_HELPER-6 2-199

IMAGE_DNLD Messages 2-199IMAGE_DNLD-SLOT#-2 2-199IMAGE_DNLD-SLOT#-4 2-200IMAGE_DNLD-SLOT#-5 2-200

IMAGE_UPGRADE Messages 2-201IMAGE_UPGRADE-SLOT#-2 2-201IMAGE_UPGRADE-SLOT#-4 2-201

IM Messages 2-201IM-3 2-201IM-5 2-202

INTERFACE_VLAN Messages 2-202INTERFACE_VLAN-4 2-202INTERFACE_VLAN-5 2-202

IOA_LC Messages 2-204IOA_LC-5 2-205

IPACL Messages 2-205ixNexus 5000 Series NX-OS System Message Reference

OL-25078-01

IPACL-0 2-205


IPACL-1 2-205IPACL-2 2-205IPACL-3 2-206IPACL-4 2-206IPACL-5 2-206IPACL-6 2-206

IPFC Messages 2-206IPFC-2 2-207IPFC-3 2-207IPFC-5 2-207IPFC-6 2-208

IPQOSMGR Messages 2-208IPQOSMGR-2 2-208IPQOSMGR-3 2-209IPQOSMGR-4 2-209IPQOSMGR-6 2-210IPQOSMGR-SLOT#-3 2-210

IPSEC Messages 2-210IPSEC-2 2-210IPSEC-3 2-211IPSEC-5 2-211

IPS_SB_MGR Messages 2-213IPS_SB_MGR-SLOT#-2 2-213IPS_SB_MGR-SLOT#-3 2-214IPS_SB_MGR-SLOT#-4 2-214IPS_SB_MGR-SLOT#-6 2-215

IPS Messages 2-215IPS-2 2-215IPS-3 2-215IPS-4 2-220IPS-5 2-221IPS-7 2-230

IPV6 Messages 2-231IPV6-2 2-231IPV6-3 2-231IPV6-4 2-231

IP Messages 2-232IP-1 2-232IP-3 2-233xNexus 5000 Series NX-OS System Message Reference

OL-25078-01

IP-4 2-233


IP-6 2-233ISAPI Messages 2-234

ISAPI-SLOT#-0 2-234ISAPI-SLOT#-1 2-235ISAPI-SLOT#-2 2-235ISAPI-SLOT#-3 2-236ISAPI-SLOT#-4 2-237ISAPI-SLOT#-5 2-238ISAPI-SLOT#-6 2-238ISAPI-SLOT#-7 2-239

ISNS Messages 2-240ISNS-2 2-240

IVR Messages 2-240IVR-2 2-240IVR-3 2-244IVR-4 2-251IVR-5 2-253IVR-6 2-256IVR-7 2-257

L2FMC Messages 2-257L2FMC-SLOT#-0 2-257L2FMC-SLOT#-2 2-257L2FMC-SLOT#-5 2-258L2FMC-SLOT#-6 2-258

L2FM Messages 2-259L2FM-0 2-259L2FM-1 2-260L2FM-2 2-261L2FM-4 2-261L2FM-6 2-262

L2MCAST Messages 2-262L2MCAST-SLOT#-0 2-262L2MCAST-SLOT#-2 2-262L2MCAST-SLOT#-6 2-263

LACP Messages 2-264LACP-3 2-264LACP-5 2-265

LC-FCFWD Messages 2-266LC-FCFWD-3 2-266xiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

LC-SPAN Messages 2-266


LC-SPAN-3 2-266LC_CFG Messages 2-266

LC_CFG-SLOT#-2 2-267LC_PORT_CHANNEL Messages 2-267

LC_PORT_CHANNEL-SLOT#-0 2-267LC_PORT_MGR Messages 2-268

LC_PORT_MGR-SLOT#-2 2-268LC_RDL Messages 2-268

LC_RDL-3 2-268LC_RDL-6 2-269

LDAP Messages 2-270LDAP-2 2-270LDAP-3 2-270LDAP-5 2-270LDAP-6 2-271

LIBBASE_SVC Messages 2-271LIBBASE_SVC-2 2-271LIBBASE_SVC-4 2-271LIBBASE_SVC-5 2-271

LIBGD Messages 2-272LIBGD-2 2-272LIBGD-3 2-272LIBGD-5 2-273LIBGD-6 2-273

LICMGR Messages 2-273LICMGR-0 2-273LICMGR-1 2-274LICMGR-2 2-274LICMGR-3 2-275LICMGR-4 2-276LICMGR-6 2-277

LLDP Messages 2-277LLDP-3 2-278LLDP-5 2-278LLDP-6 2-279

MAC Messages 2-279MAC-SLOT#-2 2-279

MCAST Messages 2-279MCAST-2 2-280xiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

MCAST-4 2-280


MCAST-5 2-280MCECTEST Messages 2-280

MCECTEST-3 2-280MCECTEST-5 2-281MCECTEST-6 2-281

MCM Messages 2-281MCM-2 2-282MCM-5 2-282MCM-6 2-282

MFDM Messages 2-282MFDM-2 2-283MODULE-3 2-286MODULE-4 2-286MODULE-5 2-287MODULE-6 2-288

MONITOR Messages 2-288MONITOR-6 2-288

NFM Messages 2-289NFM-2 2-289NFM-3 2-290NFM-4 2-292NFM-5 2-292NFM-6 2-293NFM-7 2-294

NFP Messages 2-294NFP-SLOT#-2 2-294NFP-SLOT#-5 2-295

NOHMS Messages 2-295NOHMS-2 2-295

NPC Messages 2-298NPC-SLOT#-3 2-298NPC-SLOT#-4 2-299NPC-SLOT#-5 2-299

NPV Messages 2-299NPV-2 2-299NPV-3 2-300NPV-4 2-303NPV-5 2-304NPV-6 2-305xiiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

NPV-7 2-308


NTP Messages 2-308NTP-2 2-308NTP-3 2-309NTP-6 2-309

NVP Messages 2-310NVP-6 2-310NVP-SLOT#-2 2-310

OC_USD Messages 2-311OC_USD-2 2-311

ORI_FWD Messages 2-311ORI_FWD-2 2-311ORI_FWD-6 2-311

ORI_MAC Messages 2-311ORI_MAC-2 2-311ORI_MAC-6 2-312

OTM Messages 2-312OTM-2 2-312OTM-3 2-312OTM-5 2-312OTM-6 2-312

PFMA Messages 2-313PFMA-0 2-313PFMA-1 2-316PFMA-2 2-317PFMA-3 2-328PFMA-4 2-328PFMA-5 2-329PFMA-7 2-330

PHY_USD Messages 2-330PHY_USD-SLOT#-4 2-331

PIXM Messages 2-331PIXM-2 2-331PIXM-3 2-331PIXM-4 2-332

PLATFORM Messages 2-332PLATFORM-0 2-332PLATFORM-1 2-335PLATFORM-2 2-336PLATFORM-3 2-347xivNexus 5000 Series NX-OS System Message Reference

OL-25078-01

PLATFORM-4 2-349


PLATFORM-5 2-349PLATFORM-6 2-351PLATFORM-7 2-351

PLOG_SUP Messages 2-351PLOG_SUP-4 2-351

PLOG Messages 2-351PLOG-4 2-351

PONG Messages 2-352PONG-5 2-352

PORT-CHANNEL Messages 2-352PORT-CHANNEL-1 2-352PORT-CHANNEL-2 2-353PORT-CHANNEL-3 2-353PORT-CHANNEL-4 2-355PORT-CHANNEL-5 2-355PORT-CHANNEL-6 2-357PORT-CHANNEL-7 2-357

PORT-PROFILE Messages 2-358PORT-PROFILE-2 2-358PORT-PROFILE-3 2-358PORT-PROFILE-6 2-360

PORT-RESOURCES Messages 2-360PORT-RESOURCES-3 2-361PORT-RESOURCES-5 2-361

PORT-SECURITY Messages 2-361PORT-SECURITY-2 2-361PORT-SECURITY-3 2-362PORT-SECURITY-4 2-364PORT-SECURITY-6 2-364

PORT Messages 2-364PORT-2 2-364PORT-3 2-365PORT-4 2-365PORT-5 2-366

PRIVATE_VLAN Messages 2-387PRIVATE_VLAN-2 2-387PRIVATE_VLAN-3 2-388PRIVATE_VLAN-5 2-388

PROC_MGR Messages 2-389xvNexus 5000 Series NX-OS System Message Reference

OL-25078-01

PROC_MGR-SLOT#-2 2-389


PROC_MGR-SLOT#-3 2-392PROC_MGR-SLOT#-4 2-392PROC_MGR-SLOT#-6 2-392

PSS Messages 2-392PSS-0 2-392PSS-1 2-393PSS-2 2-394PSS-4 2-395PSS-5 2-395

QOS Messages 2-396QOS-2 2-396QOS-3 2-397QOS-4 2-399QOS-6 2-399

RADIUS Messages 2-401RADIUS-2 2-401RADIUS-3 2-402RADIUS-4 2-402RADIUS-5 2-402RADIUS-6 2-403

RDL Messages 2-403RDL-2 2-403RDL-3 2-403RDL-6 2-404

RES_MGR Messages 2-405RES_MGR-1 2-405RES_MGR-2 2-405RES_MGR-3 2-406RES_MGR-4 2-406RES_MGR-5 2-407RES_MGR-6 2-407

RIB Messages 2-408RIB-0 2-408RIB-1 2-408RIB-2 2-408RIB-3 2-408RIB-4 2-409RIB-5 2-410RIB-6 2-410xviNexus 5000 Series NX-OS System Message Reference

OL-25078-01

RLIR Messages 2-410


RLIR-2 2-411RLIR-6 2-412

RM Messages 2-412RM-6 2-412RM-SLOT#-2 2-412RM-SLOT#-4 2-413

RSCN Messages 2-413RSCN-2 2-414RSCN-4 2-414RSCN-6 2-415

SAL Messages 2-415SAL-5 2-415

SAN_EXT_TUNER Messages 2-415SAN_EXT_TUNER-3 2-416

SATCTRL Message 2-416SATCTRL-SLOT#-2 2-416SATCTRL-SLOT#-4 2-418SATCTRL-SLOT#-5 2-418

SCHEDULER Messages 2-418SCHEDULER-2 2-418SCHEDULER-3 2-419SCHEDULER-4 2-419SCHEDULER-6 2-420

SCSI-TARGET Messages 2-420SCSI-TARGET-2 2-420SCSI-TARGET-3 2-421SCSI-TARGET-7 2-423

SDV Messages 2-423SDV-2 2-423SDV-3 2-423SDV-4 2-425SDV-6 2-426SDV-7 2-426

SECURITYD Messages 2-426SECURITYD-2 2-426SECURITYD-3 2-427SECURITYD-6 2-428

SENSOR_USD Messages 2-428SENSOR_USD-2 2-428xviiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

SENSOR_USD-3 2-429


SENSOR_USD-5 2-430SFC Messages 2-430

SFC-3 2-430SFM Messages 2-430

SFM-2 2-431SFM-6 2-431

SKSD Messages 2-431SKSD-5 2-431

SKT_USD Messages 2-433SKT_USD-3 2-433SKT_USD-6 2-433

SNMPD Messages 2-433SNMPD-1 2-433SNMPD-2 2-433SNMPD-3 2-434SNMPD-4 2-434SNMPD-5 2-434SNMPD-6 2-434SNMPD-7 2-434

SPAN Messages 2-434SPAN-2 2-435SPAN-3 2-435SPAN-5 2-435SPAN-6 2-436

SPI Messages 2-437SPI-SLOT#-2 2-437

STP Messages 2-437STP-2 2-437STP-3 2-445STP-4 2-445STP-6 2-446

SVC_BATTERY Messages 2-448SVC_BATTERY-SLOT#-2 2-448SVC_BATTERY-SLOT#-4 2-450SVC_BATTERY-SLOT#-6 2-450

SVC Messages 2-451SVC-0 2-451SVC-1 2-451SVC-2 2-451xviiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

SVC-3 2-452


SVC-4 2-464SVC-5 2-473SVC-6 2-473SVC-7 2-490

SYSMGR Messages 2-490SYSMGR-2 2-491SYSMGR-3 2-512SYSMGR-4 2-521SYSMGR-5 2-523SYSMGR-6 2-528SYSMGR-7 2-530

SYSTEMHEALTH Messages 2-532SYSTEMHEALTH-2 2-532SYSTEMHEALTH-4 2-535SYSTEMHEALTH-5 2-540SYSTEMHEALTH-6 2-542

TACACS Messages 2-544TACACS-2 2-544TACACS-3 2-544TACACS-5 2-544TACACS-6 2-545

TBIRD_CMN_USD Messages 2-545TBIRD_CMN_USD-6 2-545

TBIRD_FWD_USD Messages 2-545TBIRD_FWD_USD-6 2-545

TBIRD_MAC_USD Messages 2-546TBIRD_MAC_USD-3 2-546

TBIRD_QUE_USD Messages 2-546TBIRD_QUE_USD-6 2-546

TBIRD_XBAR_USD Messages 2-546TBIRD_XBAR_USD-6 2-546

TCAP Messages 2-546TCAP-2 2-547

TLPORT Messages 2-547TLPORT-2 2-547TLPORT-3 2-547TLPORT-4 2-548TLPORT-6 2-548

TPC Messages 2-549xixNexus 5000 Series NX-OS System Message Reference

OL-25078-01

TPC-SLOT#-5 2-549


TTYD Messages 2-550TTYD-2 2-550TTYD-3 2-550TTYD-6 2-551

TUNNEL Messages 2-551TUNNEL-2 2-551TUNNEL-3 2-551TUNNEL-4 2-551TUNNEL-5 2-552TUNNEL-7 2-553

UDLD Messages 2-553UDLD-3 2-553UDLD-4 2-554UDLD-5 2-555

UFDM Messages 2-555UFDM-2 2-555

VDC_MGR Messages 2-556VDC_MGR-2 2-556VDC_MGR-3 2-557VDC_MGR-6 2-557

VEC Messages 2-557VEC-SLOT#-3 2-558VEC-SLOT#-4 2-558VEC-SLOT#-5 2-558

VEDB_MGR Messages 2-562VEDB_MGR-2 2-562VEDB_MGR-6 2-562

VEM_MGR Messages 2-562VEM_MGR-2 2-563

VES Messages 2-565VES-SLOT#-4 2-565VES-SLOT#-5 2-566

VFC Messages 2-567VFC-3 2-567VFC-6 2-567

VIM Messages 2-567VIM-3 2-567VIM-4 2-568VIM-5 2-568xxNexus 5000 Series NX-OS System Message Reference

OL-25078-01

VLAN_MGR Messages 2-571


VLAN_MGR-2 2-571VLAN_MGR-4 2-572VLAN_MGR-6 2-572

VMM Messages 2-572VMM-2 2-573

VNI Messages 2-573VNI-2 2-573VNI-3 2-573VNI-6 2-573

VPC Messages 2-574VPC-2 2-574VPC-3 2-575VPC-4 2-577VPC-5 2-578VPC-6 2-579

VPM Messages 2-583VPM-2 2-583VPM-3 2-584VPM-4 2-585VPM-6 2-585VPM-SLOT#-2 2-587

VRRP-CFG Messages 2-587VRRP-CFG-2 2-588VRRP-CFG-3 2-588VRRP-CFG-5 2-588

VRRP-ENG Messages 2-588VRRP-ENG-2 2-589VRRP-ENG-3 2-589VRRP-ENG-4 2-590VRRP-ENG-5 2-591VRRP-ENG-6 2-592

VSAN Messages 2-592VSAN-2 2-592VSAN-3 2-592VSAN-6 2-593

VSD Messages 2-594VSD-SLOT#-2 2-594

VSHD Messages 2-594VSHD-2 2-594xxiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

VSHD-3 2-595


VSHD-4 2-595VSHD-5 2-596VSHD-7 2-596

WWN Messages 2-597WWN-1 2-597WWN-2 2-597WWN-3 2-599WWN-4 2-600WWN-5 2-600WWN-6 2-601WWN-7 2-602

XBAR_CLIENT Messages 2-602XBAR_CLIENT-2 2-603XBAR_CLIENT-3 2-604XBAR_CLIENT-SLOT#-2 2-605XBAR_CLIENT-SLOT#-3 2-605

XBAR Messages 2-605XBAR-2 2-606XBAR-3 2-606XBAR-5 2-606

XMLMA Messages 2-611XMLMA-2 2-611XMLMA-3 2-612XMLMA-5 2-612XMLMA-6 2-612

XMLSA Messages 2-612XMLSA-2 2-612XMLSA-5 2-613XMLSA-6 2-613

ZBM Messages 2-613ZBM-2 2-614ZBM-4 2-615ZBM-6 2-616

ZONE Messages 2-617ZONE-2 2-617ZONE-3 2-625ZONE-4 2-626ZONE-5 2-628ZONE-6 2-629xxiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

Send document comments to nexus5k -doc feedback@c i sco .com

Preface

This document lists and describes the system messages for Cisco Nexus 5000 and Nexus 2000 series switches. The system software sends these messages to the console (and, optionally, to a logging server on another system) during operation. Not all messages indicate a problem with your system. Some messages are purely informational, while others might help diagnose problems with links, internal hardware, or the system software.This document includes system messages for all Cisco Nexus 5000 and Nexus 2000 series software releases.This preface describes the audience, organization, and conventions of this guide. It also provides information on how to obtain related documentation.

AudienceThis guide is for system administrators who are responsible for managing Cisco Nexus 5000 and Nexus 2000 series systems.

OrganizationThis guide is organized as follows:

Chapter Title Description

Chapter 1 Introduction to System Messages for Cisco NX-OS

Describes the structure of system messages and the format of system log files.

Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 Family

Lists the messages that may appear in log files, and indicates suggested remedies where applicable for the Cisco Nexus 5000 and Nexus 2000 Series.xviiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

Document ConventionsCommand descriptions use these conventions:

Convention Description

boldface font Commands and keywords are in boldface.


PrefaceDocument ConventionsScreen examples use these conventions:

This document uses the following conventions:

Note Means reader take note. Notes contain helpful suggestions or references to material not covered in the manual.

Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data.

Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly Whats New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at:http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.htmlSubscribe to the Whats New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

italic font Arguments for which you supply values are in italics.[ ] Elements in square brackets are optional.[ x | y | z ] Optional alternative keywords are grouped in brackets and separated by vertical

bars.string A nonquoted set of characters. Do not use quotation marks around the string or

the string will include the quotation marks.

screen font Terminal sessions and information that the switch displays are in screen font.boldface screen font

Information that you must enter is in boldface screen font.

italic screen font Arguments for which you supply values are in italic screen font.< > Nonprinting characters, such as passwords, are in angle brackets.[ ] Default responses to system prompts are in square brackets.!, # An exclamation point (!) or a pound sign (#) at the beginning of a line of code

indicates a comment line.xviiiNexus 5000 Series NX-OS System Message Reference

OL-25078-01

NeOL-25078-01

.

Table 1-1 System Log Message Format Des

Element Description

month dd The date and month of the hh:mm:ss The time of the error or evcription

error or eventC H A P T E R


1Introduction to System Messages for Cisco NX-OS

This chapter describes system messages, as defined by the syslog protocol (RFC 3164). It describes how to understand the syslog message format and how to capture system messages for review.This chapter contains the following sections:

System Log Message Format, page 1-1 Capturing System Messages and History, page 1-5

System Log Message FormatSystem log messages begin with a percent sign (%) and are displayed in the following formats: Syslog Format On a Resident Switch, page 1-1 Syslog Format On a Remote-Logging Server, page 1-3

Syslog Format On a Resident SwitchThe format for a resident syslog is:month dd hh:mm:ss switchname facility-severity-MNEMONIC descriptionor

month dd hh:mm:ss switchname facility-SLOTnumber-severity-MNEMONIC descriptionor

month dd hh:mm:ss switchname facility-STANDBY-severity-MNEMONIC description

For example:Nov 1 14:07:58 excal-113 %MODULE-5-MOD_OK: Module 1 is onlineNov 1 14:07:58 excal-113 %PORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver for interface fc1/13 is not supported1-1xus 5000 Series NX-OS System Message Reference

ent


Chapter 1 Introduction to System Messages for Cisco NX-OSSystem Log Message FormatFACILITY is a code consisting of two or more uppercase letters that indicate the facility to which the system message refers. A facility is a hardware device, a protocol, a feature, or a module of the system software. System message SEVERITY codes range from 0 to 7 and reflect the severity of the condition. The lower the number, the more serious the situation. Table 1-2 lists the severity levels.

MNEMONIC is a code that uniquely identifies the system message. Message-text is a text string that describes the condition. This portion of the message might contain detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 1-3 lists the representations of variable fields and the type of information in the fields.

switchname The name of the switchfacility The facility of the error or event (daemon, kernel, VSHD, or other facility)severity Single-digit code from 0 to 7 that indicates the severity of the messageMNEMONIC Text string that uniquely describes the system message%$VDC #%$ An optional virtual device context (VDC) ID that appears in the description for

messages requiring VDC IDs%$VRF #%$ An optional virtual routing and forwarding (VRF) ID that appears in the

description for messages requiring VRF IDsdescription Text string containing detailed information about the event being reported

Table 1-1 System Log Message Format Description (continued)

Element Description

Table 1-2 System Message Severity Levels

Level Description

0 emergency System unusable1 alert Immediate action needed2 critical Critical condition3 error Error condition4 warning Warning condition5 notification Normal but significant condition6 informational Informational message only7 debugging Appears during debugging only

Table 1-3 Representation of Variable Fields in System Messages

Representation Type of Information

[dec] Decimal number[hex] Hexadecimal number1-2Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 1 Introduction to System Messages for Cisco NX-OSSystem Log Message FormatThe following example system message shows how the variable field might be used:%MODULE-5-MOD_MINORSWFAIL: Module [dec] reported a failure in service [chars]In this example,

Facility code =MODULE (indicating that it is a module-specific error)Severity =5 (notification)Alarm/event code= MOD_MINORSWFAILDescription of the problem= Module [dec] reported a failure in service [chars] [dec] is the module slot number associated with this message.[chars] is the service name that experienced this failure.

System log messages begin with a percent sign (%) and are displayed in the following format (see Table 1-4).

Syslog Format On a Remote-Logging ServerThe syslog format on a remote-logging server is:month dd hh:mm:ss IP-addr-switch : year month day hh:mm:ss Timezone: facility-severity-MNEMONIC descriptionor

month dd hh:mm:ss IP-addr-switch : year month day hh:mm:ssTimezone: facility-SLOTnumber-severity-MNEMONIC descriptionor

month dd hh:mm:ss IP-addr-switch : year month day hh:mm:ss Timezone: facility-STANDBY-severity-MNEMONIC descriptionFor example:sep 21 11:09:50 172.22.22.45 : 2005 Sep 04 18:18:22 UTC: %AUTHPRIV-3-SYSTEM_MSG: ttyS1:togetattr: Input/output error - getty[28224]switch resident syslog 2005 Sep 4 18:18:22 switch %AUTHPRIV-3-SYSTEM_MSG: ttyS1:togetattr: Input/output error - getty[28224]time on switch : 2005 Sep 4 18:18:22 time on Loggng Server : Sep 21 11:09:50 fc1/13 is not supported.

[char] Single character[chars] Character string



Table 1-4 System Log Message Format Description

Element Description

month dd The date and month of the error or eventhh:mm:ss The time of the error or eventIP-addr-switch The IP address of the switchfacility The facility of the error or event (daemon, kernel, VSHD, or other facility)severity Single-digit code from 0 to 3 that indicates the severity of the messageMNEMONIC Text string that uniquely describes the system message1-3Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 1 Introduction to System Messages for Cisco NX-OSSystem Log Message FormatFACILITY is a code consisting of two or more uppercase letters that indicate the facility to which the system message refers. A facility is a hardware device, a protocol, a feature, or a module of the system software. System message SEVERITY codes range from 0 to 3 and reflect the severity of the condition. The lower the number, the more serious the situation. Table 1-5 lists the severity levels.

MNEMONIC is a code that uniquely identifies the system message. Message-text is a text string that describes the condition. This portion of the message might contain detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 1-6 lists the representations of variable fields and the type of information in the fields.

The following example system message shows how the variable field might be used:%AUTHPRIV-3-SYSTEM_MSG: AUTHPRIV [dec] reported a failure in service [chars]In this example,

Facility code =AUTHPRIV (indicating that it is a authpriv-specific error)Severity =3 (notification)

%$VDC #%$ An optional virtual device context (VDC) ID that appears in the description for messages requiring VDC IDs

%$VRF #%$ An optional virtual routing and forwarding (VRF) ID that appears in the description for messages requiring VRF IDs

description Text string containing detailed information about the event being reported

Table 1-4 System Log Message Format Description (continued)

Element Description

Table 1-5 System Log Message Format description

Level Description

0 emergency System unusable1 alert Immediate action needed2 critical Critical condition3 notification Normal but significant condition



[dec] Decimal number[hex] Hexadecimal number[char] Single character[chars] Character string1-4Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 1 Introduction to System Messages for Cisco NX-OSCapturing System Messages and HistoryAlarm/event code= SYSTEM_MSGDescription of the problem= Authpriv [dec] reported a failure in service [chars] [dec] is the module slot number associated with this message.[chars] is the service name that experienced this failure.

Capturing System Messages and HistoryThe system messages are displayed instantly on the console, by default, or are redirected to an internal log file, or a syslog server. System message severity levels correspond to the keywords assigned by the logging global configuration commands. These keywords define where and at what level these messages appear (see to the Cisco NX-OS System Management Configuration Guide). Only system messages that correspond to the configured logging level or higher severity messages are logged. As an example, if you set the logging level to 3 (error), then you get error, critical, alerts, and emergency system messages, but you do not get warning, notification, informational, or debugging system messages.For complete information about handling system messages, see the Cisco NX-OS System Management Configuration Guide, Release 4.1.

Saving the System Messages LogThe logging logfile global configuration command enables copying of system messages to an internal log file and optionally sets the size of the file. To display the messages that are logged in the file, use the show logging EXEC command. The first message displayed is the oldest message in the buffer. To clear the current contents of the buffer, use the clear debug-logfile command.

Logging System Messages to a Syslog ServerThe logging host-name command identifies a syslog server host to receive logging messages. The host-name argument is the name or Internet address of the host. By issuing this command more than once, you build a list of syslog servers that receive logging messages. The no logging host-name command deletes the syslog server with the specified address from the list of syslog servers.1-5Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 1 Introduction to System Messages for Cisco NX-OSCapturing System Messages and History1-6Nexus 5000 Series NX-OS System Message Reference

OL-25078-01

NeOL-25078-01

Recommended Action Please contact the Ciscosupport. If you have purchased a Cisco suppo reseller through which you procured the product for rt contract please call Cisco TAC for support. C H A P T E R


2System Messages and Recovery Procedures for the Cisco Nexus 5000 Family

This chapter includes system messages for the Cisco NX-OS Nexus 5000 and Nexus 2000 family of switches. The messages are listed in alphabetical order by the system facility that produces them. Within each system facility section, messages are listed alphabetically by severity and mnemonics. Each error message is followed by an explanation and a recommended action.

AAA MessagesThis section contains the AAA messages.

AAA-1

Error Message AAA-1-AAA_SESSION_LIMIT_REJECT: aaa request rejected as maximum aaa sessions are in progress

Explanation Aaa request rejected as the limit for maximum concurrent aaa sessions is reached Recommended Action Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

AAA-2

Error Message AAA-2-AAA_NVRAM_UPGRADE_FAILURE: upgrading of accounting log failed. [chars]

Explanation Upgrading of accounting log failed. 2-1xus 5000 Series NX-OS System Message Reference


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message AAA-2-AAA_PROGRAM_EXIT: aaa daemon exiting: [chars]

Explanation Aaa daemon is exiting.

Recommended Action Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support.

AAA-3

Error Message AAA-3-AAA_NVRAMFAILURE: nvram failure

Explanation Nvram can not be read/written to. Hence accounting log can not be stored there


AAA-6

Error Message AAA-6-AAA_ACCOUNTING_MESSAGE: [chars]

Explanation Accounting Message

Recommended Action No action is required.

AAM MessagesThis section contains the AAM messages.

AAM-2

Error Message AAM-2-ELS_FC2_GL_SINDEX_LOOKUP_FAILED: Failed to lookup global port index for interface [[chars]]

Explanation Failed to lookup global port index for interface [chars]


AAM-3

Error Message AAM-3-ALLOC_FAILED: Failed in File:[chars] Line:[dec] for type [dec] size [dec]

Explanation AAM process could not allocate heap memory in File:[chars], at line:[dec], for memory-type:[dec] of Size:[dec]

Recommended Action No action is required. 2-2Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message AAM-3-ASSERTION_FAILED: Failed in File:[chars] Line:[dec]

Explanation AAM Process assertion failed in File:[chars], at line:[dec]


ACLLOG MessagesThis section contains the ACLLOG messages.

ACLLOG-4

Error Message ACLLOG-4-ACLLOG_MAXFLOW_REACHED: [chars]

Explanation Max flow reached in current interval: [chars]


Error Message ACLLOG-4-ACLLOG_THRESHOLD: [chars]

Explanation Threshold Reached for Flow: [chars]


ACLLOG-6

Error Message ACLLOG-6-ACLLOG_FLOW_INTERVAL: [chars]

Explanation Flow info in current alert interval: [chars]


Error Message ACLLOG-6-ACLLOG_NEW_FLOW: [chars]

Explanation New Acllog Flow: [chars]


ACLMGR MessagesThis section contains the ACLMGR messages.2-3Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyACLMGR-2

Error Message ACLMGR-2-ACLMGR_COMMIT_FAIL: Commit failed: client %llX, [chars]

Explanation The PPF commit failed


Error Message ACLMGR-2-ACLMGR_NO_ERRDISABLED: [chars] event on interface [chars] ([hex]) allowed to succeed in spite of access-list failure

Explanation Although an access-list operation failed during a port event, the port event still finished successfully because errdisable is disallowed


Error Message ACLMGR-2-EXITING: Exit reason: [chars]

Explanation The ACLMGR service process has exited due to [char]. The process has probably been restarted automatically.


Error Message ACLMGR-2-INITFAIL: ACLMGR Service Init failed: [chars]

Explanation ACLMGR Service initialization failed. [chars] explains the reason for the failure.


Error Message ACLMGR-2-MALLOC_ERROR: Size [dec] bytes

Explanation The ACLMGR service could not allocate memory.


Error Message ACLMGR-2-PSS_ERROR: [chars]: PSS ret. val=[dec]

Explanation The ACLMGR service encountered error while operating on a persistent storage database.


OL-25078-01



Error Message ACLMGR-3-ACLMGR_ACL_ON_FAB_INACTIVE: ACL on FEX fabric interface not activated

Explanation ACL applied to a FEX fabric port or port-channel is not activated


Error Message ACLMGR-3-ACLMGR_ACL_OVER_FAB_CHANNEL: ACL on FEX fabric port-channel bound interface not activated

Explanation ACL applied to a FEX interface is not activated if the interface is bound to a FEX-fabric portchannel


Error Message ACLMGR-3-ACLMGR_DB_LOCK_MSG: ACL database message, reason: [chars], session 0x%llx, type: [chars]

Explanation ACL PPF database lock acquire/release related message.


Error Message ACLMGR-3-ACLMGR_PPF_ERROR: PPF error: [chars]

Explanation The PPF generated error


Error Message ACLMGR-3-ACLMGR_PSS_CORRUPTED: [chars] PSS found corrupted

Explanation The ACLMGR service has detected corruption in one of its persistent information database. The database would be recreated.


Error Message ACLMGR-3-ACLMGR_STAT_CONSOLIDATION_FAILURE: ACL statistic parsing or consolidation failed

Explanation A statistic update failed during the parsing or consolidation step; statistics may have been lost


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLMGR-3-ACLMGR_VACL_REDIRECTION_DISABLED_REMOVAL: VACL redirection to interface [chars] ([hex]) disabled: the port has been removed

Explanation A VACL redirection to the port has been deactivated because the port has been removed


Error Message ACLMGR-3-ACLMGR_VERIFY_FAIL: Verify failed: client %llX, [chars]

Explanation The PPF Verify failed


Error Message ACLMGR-3-MTSERROR: [chars]

Explanation ACLMGR Service encountered an MTS error. [chars] specifies the context where the error occured.


ACLMGR-4

Error Message ACLMGR-4-ACLMGR_PPF_WARNING: PPF warning: [chars]

Explanation The PPF generated warning


Error Message ACLMGR-4-ACLMGR_VACL_REDIRECTION_DISABLED_PCM: VACL redirection to interface [chars] ([hex]) disabled: the port became a portchannel member

Explanation A VACL redirection to the port has been temporarily deactivated because it is now a member in a port channel


Error Message ACLMGR-4-PSS_VERSION_MISMATCH: PSS [dec] Code [dec]

Explanation There was a version mismatch between the ACLMGR service and one of its persistent storage databases. The persistent information has been translated to the new format.

Recommended Action No action is required.2-6Nexus 5000 Series NX-OS System Message Reference

OL-25078-01



Error Message ACLMGR-6-ACLMGR_PPF_NOTIF: PPF notification: [chars]

Explanation The PPF generated notification


Error Message ACLMGR-6-BECAME_ACTIVE: Became ACTIVE from standby mode

Explanation The ACLMGR service on the standby supervisor became active and it is ready to serve client requests.


Error Message ACLMGR-6-BECAME_STDBY: Became STANDBY from active mode

Explanation The ACLMGR service became standby from active mode.


Error Message ACLMGR-6-FAILED_TO_SEND_HEARTBEAT: Failed to send heartbeat to system manager: Reason=[chars]

Explanation The ACLMGR service was unable to send heartbeat to the system manger


Error Message ACLMGR-6-SERVICE_UP: Initialized [chars]

Explanation The ACLMGR service is up and ready The service was initialized in [char] mode.


Error Message ACLMGR-6-SRVEXIT: ACLMGR Service shutting down gracefully

Explanation ACLMGR Service is shutting down gracefully. This is an informational message.


Error Message ACLMGR-6-SWITCHOVER: Switching Over to other Sup.

Explanation The ACLMGR service has successfully switched over to the standby supervisor card.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyACLQOS MessagesThis section contains the ACLQOS messages.

ACLQOS-SLOT#-2

Error Message ACLQOS-SLOT#-2-ACLQOS_FAILED: ACLQOS failure: [chars]

Explanation ACLQOS operation failed in the aclqos client

Recommended Action No DDTS.

Error Message ACLQOS-SLOT#-2-ACLQOS_INBAND_INTERFACE_FAILURE: Inband interface lif lookup failed ([chars])

Explanation Inband interface lif lookup failed


Error Message ACLQOS-SLOT#-2-ACLQOS_MALLOC_FAILED: Memory allocation failed. [chars]

Explanation Memory allocation failed. This is a critical failure


Error Message ACLQOS-SLOT#-2-ACLQOS_OOTR: Tcam resource exhausted: [chars]

Explanation Tcam resources to program acls exhausted


Error Message ACLQOS-SLOT#-2-PPF_FAILED: Database failure: [chars]

Explanation Database operation failed in the aclqos client


ACLQOS-SLOT#-3

Error Message ACLQOS-SLOT#-3-ACLQOS_CC_INVALID: Invalid Congestion Control parameters

Explanation Invalid Congestion Control parameters

Recommended Action No DDTS. 2-8Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLQOS-SLOT#-3-ACLQOS_PAUSE_INVALID: Invalid Pause parameters

Explanation Invalid Pause parameters


Error Message ACLQOS-SLOT#-3-ACLQOS_QUEUING_ERROR: ACL/QoS queuing error: [chars]

Explanation Internal error in ACL/QoS queuing config


ACLQOS-SLOT#-4

Error Message ACLQOS-SLOT#-4-ACLQOS_ATOMIC_ERR: [chars]

Explanation Tcam will be overused, please turn off atomic update


Error Message ACLQOS-SLOT#-4-ACLQOS_MATCH_ALL_MERGE_UPDATE: Warning (match_all merging): [chars]

Explanation Warning (match_all merging)


Error Message ACLQOS-SLOT#-4-ACLQOS_OVER_THRESHOLD: Tcam [dec] Bank [dec]'s usage has reached its threshold

Explanation Tcam is almost full


Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_COS2Q_INVALID: ACL/QoS invalid queuing policy because of cos map change: [chars] queue [chars], interface [chars]

Explanation Attemped to configure an invalid queuing policy


Error Message ACLQOS-SLOT#-4-ACLQOS_QUEUING_INVALID: ACL/QoS invalid queuing policy: [chars]

Explanation Attemped to configure an invalid queuing policy


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLQOS-SLOT#-4-ACLQOS_UNDER_THRESHOLD: Tcam [dec] Bank [dec]'s usage is below the threshold now

Explanation Tcam's usage is below the threshold


Error Message ACLQOS-SLOT#-4-ACLQOS_WARNING: ACLQOS Warning: [chars]

Explanation ACLQOS Warnings


ACLQOS-SLOT#-5

Error Message ACLQOS-SLOT#-5-ACLQOS_DISRUPTIVE_IPv6_UPDATE: Disruptive update of IPv6 compression entries

Explanation Disruptive IPv6 compression entries update


Error Message ACLQOS-SLOT#-5-ACLQOS_NON_ATOMIC: Non atomic ACL/QoS policy update done for [chars]

Explanation Non atomic ACL/QoS policy update was done


ACLTCAM MessagesThis section contains the ACLTCAM messages.

ACLTCAM-2

Error Message ACLTCAM-2-ACL_TCAM_ADJ_EXHAUSTED: ACLTCAM failed to program route for VSAN: [dec], SID: [chars] DID: [chars], error: [chars].

Explanation ACLTCAM process experienced a failure while programming route for VSAN [dec] SID [chars] DID [chars] due to resource exhaustion. [chars] is the error code.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLTCAM-2-ACL_TCAM_ALMOST_FULL: TCAM close to FULL. [chars] TCAM Usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]

Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars]


Error Message ACLTCAM-2-ACL_TCAM_CONFIG_READ_FROM_DRIVER_FAILED: [chars] [dec], Error: [hex].

Explanation Unable to read configuration from forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].


Error Message ACLTCAM-2-ACL_TCAM_CONFIG_WRITE_TO_DRIVER_FAILED: [chars] [dec], Error: [hex].

Explanation Unable to write configuration to forwarding engine ASIC driver. [chars] [dec], Error: 0x[hex].


Error Message ACLTCAM-2-ACL_TCAM_FLOW_STATS_READ_FAILED: Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).

Explanation Hardware flow stats read failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).


Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_DATABASE: Database found inconsistent.

Explanation Database found inconsistent.


Error Message ACLTCAM-2-ACL_TCAM_INCONSISTENT_TCAM_CONTENTS: TCAM contents found inconsistent.

Explanation TCAM contents are found inconsistent.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLTCAM-2-ACL_TCAM_INIT_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM.

Explanation Initialization failed for forwarding engine ASIC [dec], in [chars] TCAM.


Error Message ACLTCAM-2-ACL_TCAM_INIT_REGIONS_FAILED: Initialization failed for forwarding engine ASIC: [dec], [chars] TCAM, [chars] Region.

Explanation Initialization of regions failed for forwarding engine ASIC [dec], in [chars] TCAM, for [chars] Region.


Error Message ACLTCAM-2-ACL_TCAM_MALLOC_FAILURE: Memory allocation failed for size [dec].

Explanation Memory allocation is failed for size [dec] bytes.

Recommended Action Restart the process.

Error Message ACLTCAM-2-ACL_TCAM_MTS_FAILURE: MTS operation failed: [chars].

Explanation MTS operation failed. [chars] is the reason.


Error Message ACLTCAM-2-ACL_TCAM_MTS_REGISTRATION_FAILED: MTS registration failed for opCode: [dec].

Explanation MTS registration failed for opCode: [dec].


Error Message ACLTCAM-2-ACL_TCAM_NO_ROUTE: ACLTCAM failed to get route for VSAN: [dec], Rewrite: [chars] DID: [chars] DID MASK: [chars], error: [hex].

Explanation ACLTCAM process experienced a failure while getting route for VSAN [dec] Rewrite [chars] DID [chars] DID Mask [chars]. [hex] is the error code.


Error Message ACLTCAM-2-ACL_TCAM_NO_TCAM_LEFT: ACLTCAM resource exhausted for interface : [chars]

Explanation ACLTCAM hardware resource is completely used.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_FAILED: [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).

Explanation [chars] read from hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).


Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_READ_INVALID: Invalid([chars], value: [dec]) TCAM entry read from hardware TCAM (FWD-Engine: [dec], [chars] TCAM, Address: [dec]), Ignoring this entry.

Explanation Invalid([chars], value: [dec]) TCAM entry from hardware TCAM(FWD-Engine: [dec], [chars] TCAM, Address: [dec]) Ignoring this entry


Error Message ACLTCAM-2-ACL_TCAM_PHY_TCAM_WRITE_FAILED: [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec], Error: [chars]).

Explanation [chars] write to hardware TCAM failed(ASIC: [dec], [chars] TCAM, Address: [dec], Num Entries: [dec] Error: [chars]).


Error Message ACLTCAM-2-ACL_TCAM_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].

Explanation Failed to do PSS operation [chars]. [hex] is the reason.


Error Message ACLTCAM-2-PSS_OPEN_FAILED: PSS open failed - [hex].

Explanation Persistent database handle could not obtained for ACLTCAM. [hex] is the error.


Error Message ACLTCAM-2-RECONS_FAILED: Reconstruction of TCAM contents failed during upgrade - [hex].

Explanation During non-disruptive upgrade, the ACLTCAM contents are not properly reconstructed. [hex] is the error.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyACLTCAM-3

Error Message ACLTCAM-3-REGISTER_FAILED: Could not register to MTS opcode [chars] - error [hex].

Explanation ACLTCAM process could not register to the notifications mentioned by [chars]. [hex] is the error.


ACLTCAM-4

Error Message ACLTCAM-4-ACL_TCAM_BELOW_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) fell below [dec]% fwd-eng: [dec], [chars]

Explanation [chars] TCAM usage [dec]/[dec] fell below [dec] percent on fwd-engine [dec], [chars]


Error Message ACLTCAM-4-ACL_TCAM_BEYOND_THRESHOLD: [chars] TCAM usage ([dec]/[dec]) exceeded [dec]% fwd-eng: [dec], [chars]

Explanation [chars] TCAM usage [dec]/[dec] exceeded [dec] percent on fwd-engine [dec], [chars]


Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_INVALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] with statistics: frames = %llu & bytes = %llu was invalidated due to: [chars]

Explanation ACLTCAM process invalidated the flow counter for flow VSAN [dec] SID [hex] DID [hex] with collected stats of [dec] frames and [dev] bytes was invalidated because of reason [[chars]].


Error Message ACLTCAM-4-ACL_TCAM_FLOW_COUNTER_VALIDATED: Flow counter for flow: vsan: [dec], sid: [hex], did: [hex] is now valid

Explanation ACLTCAM process validated the flow counter for flow VSAN [dec] SID [hex] DID [hex].


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyACLTCAM-6

Error Message ACLTCAM-6-ACL_TCAM_STATUS: Status: [chars].

Explanation ACLTCAM status is reported as: [chars].


ACL MessagesThis section contains the ACL messages.

ACL-2

Error Message ACL-2-ACL_HA_FAILURE: Failed to do high availability operation: [chars].

Explanation Failed to do high availability operation. [chars] is the reason.


Error Message ACL-2-ACL_INIT_FAILED: Initialization failed for ACL: [chars], reason: [hex].

Explanation Initialization failed for ACL due to [chars], reason: [hex].


Error Message ACL-2-ACL_LINECARD_STATUS: Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].

Explanation Status from linecard: [dec], for module: [chars](ID: [dec]), status : [dec], error_id: [hex], catastrophic: [chars], restart count: [dec].


Error Message ACL-2-ACL_MTS_FAILURE: Failed to do MTS operation: [chars].

Explanation Failed to do MTS operation. [chars] is the reason.


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACL-2-ACL_MTS_REGISTRATION_FAILED: MTS options setting to [hex] failed for opCode: [dec].

Explanation MTS options setting to [hex] failed for opCode: [dec].


Error Message ACL-2-ACL_PENDING_MSG_ARR_FULL: ACL Upgrade Pending Messages Array is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]

Explanation ACL Upgrade Pending Messages Array is Full with [dec] messages. Failing the MTS message with Opc: [dec], RR_TOKEN: [hex]


Error Message ACL-2-ACL_PSS_FAILURE: Failed to do PSS operation: [chars], reason: [hex].

Explanation Failed to do PSS operation [chars]. [hex] is the reason.


Error Message ACL-2-ACL_PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec].

Explanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version.


Error Message ACL-2-ACL_RUNTIME_FAILURE: [chars] [dec], Error: [hex]

Explanation ACL runtime failure is reported as [chars] [dec], reason: [hex].


Error Message ACL-2-ACL_TCAM_FAILURE: Failed to do TCAM operation: [chars].

Explanation Failed to do TCAM operation. [chars] is the reason.


ACL-4

Error Message ACL-4-ACL_WARNING: [chars] [dec]

Explanation ACL warning messages is reported as [chars] [dec].


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyACL-5

Error Message ACL-5-ACL_ADJ_SHARING_STATUS: Successfully completed [chars] on Generation 2 linecards.

Explanation Successfully completed the command \[chars]\ on Generation 2 linecards.


ACL-6

Error Message ACL-6-ACL_DIAG_EVENT_STATUS: [chars] [hex].

Explanation ACL system health management event status is reported as [chars] [hex].


Error Message ACL-6-ACL_E_PORT_EVENT_STATUS: [chars] [chars].

Explanation ACL xEport event status is reported as [chars] [chars].


Error Message ACL-6-ACL_FCC_EVENT_STATUS: [chars] [chars].

Explanation ACL FCC event status is reported as [chars] [chars].


Error Message ACL-6-ACL_LINECARD_EVENT_STATUS: [chars] [hex].

Explanation ACL linecard event status is reported as [chars] [dec].


Error Message ACL-6-ACL_MCAST_EVENT_STATUS: [chars] [chars].

Explanation ACL multicast event status is reported as [chars] [chars].


Error Message ACL-6-ACL_NX_PORT_EVENT_STATUS: [chars] [chars].

Explanation ACL Nx Port event status is reported as [chars] [chars].


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ACL-6-ACL_PORT_MODE_EVENT_STATUS: [chars] [chars].

Explanation ACL portmode event status is reported as [chars] [chars].


Error Message ACL-6-ACL_RUNTIME_STATUS: [chars] [dec]

Explanation ACL runtime status is reported as [chars] [dec].


Error Message ACL-6-ACL_SPAN_DEST_CONFIG_STATUS: [chars] [chars].

Explanation ACL SPAN destination config event status is reported as [chars] [chars].


Error Message ACL-6-ACL_SPAN_SRC_CONFIG_STATUS: [chars] [chars].

Explanation ACL SPAN source config event status is reported as [chars] [chars].


Error Message ACL-6-ACL_STATUS: ACL Status: [chars].

Explanation ACL status is reported as [chars].


Error Message ACL-6-ACL_UPDATE_SSRAM_QOS_EVENT_STATUS: [chars] [chars].

Explanation ACL update SSRAM for QoS event status is reported as [chars] [chars].


ASCII-CFG MessagesThis section contains the ASCII-CFG messages.2-18Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyASCII-CFG-2

Error Message ASCII-CFG-2-ACFG_CONFIGURATION_APPLY_ERROR: Error encountered while Ascii configuration was being applied. Please use show startup-config log to view details

Explanation At least one command failed while Ascii configuration was being applied


Error Message ASCII-CFG-2-ACFG_LIB_INVOKE_ERR: Ascii config library invocation error: [chars]

Explanation Error encountered while library function was being invoked to display Ascii configuration


Error Message ASCII-CFG-2-ACFG_OPER_FAIL: Operation failed because of [chars]

Explanation Operation failed


Error Message ASCII-CFG-2-ACFG_ROLLBACK_FAILED: Rollback to checkpoint [chars] Failed, Going to undo the changes (atomic option)

Explanation Rollback operation failed for atomic option


Error Message ASCII-CFG-2-ACFG_ROLLBACK_UNDO_FAILED: Undo failed for atomic Rollback, Please correct the error manually and retry rollback

Explanation Undoing the rollback changes (for atomic behavior) Failed


Error Message ASCII-CFG-2-ACFG_SYSLOG_INIT_FAILED: Ascii config Syslog Init Error

Explanation Error encountered while Initializing Syslog for Ascii Config


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ASCII-CFG-2-PSS_VER_FAIL: PSS file [chars] has version [dec].[dec].[dec], expected version [dec].[dec].[dec]

Explanation There was a mismatch in the PSS version. [chars] indicates the PSS service, [dec].[dec].[dec] its current version number and [dec].[dec].[dec] the expected version


ASCII-CFG-3

Error Message ASCII-CFG-3-ACFG_MTSERROR: [chars]

Explanation Ascii-cfg-server (rollback process) encountered an MTS error. [chars] specifies the context where the error occurred.


ASCII-CFG-6

Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CLEAR_DATABASE: cleared all the configuration checkpoints

Explanation Cleared all the configuration checkpoints


Error Message ASCII-CFG-6-ACFG_CHECKPOINT_CREATED: Created configuration checkpoint [chars]

Explanation Created configuration checkpoint


Error Message ASCII-CFG-6-ACFG_CHECKPOINT_DELETED: Deleted configuration checkpoint [chars]

Explanation Deleted configuration checkpoint


Error Message ASCII-CFG-6-ACFG_MAX_CHECKPOINTS: Maximum no of checpoints reached, Removing the oldest checkpoint

Explanation Maximum no.of checkpoints reached, removing the oldest checkpoint


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ASCII-CFG-6-ACFG_ROLLBACK_ATOMIC: Performing configuration rollback to checkpoint [chars] (with atomic option)

Explanation Performing configuration rollback with atomic option


Error Message ASCII-CFG-6-ACFG_ROLLBACK_BEST: Performing configuration rollback to checkpoint [chars] (with best-effort option)

Explanation Performing configuration rollback with best-effort option


Error Message ASCII-CFG-6-ACFG_ROLLBACK_FIRST_ERR: Performing configuration rollback to checkpoint [chars] (with stop-at-first failure option)

Explanation Performing configuration rollback with stop-at-first-failure option


Error Message ASCII-CFG-6-INFORMATION: [chars]

Explanation An event happend that affects Acfg-Rollback. [chars] indicates the event


Error Message ASCII-CFG-6-PSS_ERR: [chars]

Explanation An error occurred during an Acfg PSS operation. [chars] indicates the PSS operation that caused the error


ASSOC MGR MessagesThis section contains the ASSOC MGR messages.

ASSOC MGR-0

Error Message ASSOC_MGR-0-EMERGENCY_MSG: [chars]

Explanation Association Manager Emergency Message

Recommended Action Please file the bug for Association Manager Component thro' CDETS 2-21Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyASSOC_MGR-1

Error Message ASSOC_MGR-1-ALERT_MSG: [chars]

Explanation Association Manager Alert Message

Recommended Action Association Manager Internal Operation Alert

ASSOC_MGR-2

Error Message ASSOC_MGR-2-CRITICAL_MSG: [chars]

Explanation Association Manager Critical Message


ASSOC_MGR-3

Error Message ASSOC_MGR-3-ERROR_MSG: [chars]

Explanation Association Manager Error Message


ASSOC_MGR-4

Error Message ASSOC_MGR-4-WARN_MSG: [chars]

Explanation Association Manager Warning Message


ASSOC_MGR-5

Error Message ASSOC_MGR-5-NOTIF_MSG: [chars]

Explanation Association Manager Notification Message


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyASSOC_MGR-6

Error Message ASSOC_MGR-6-ASSOC_ACTIVATED: Association Activated for vlan id:[dec] vsan id:[dec]

Explanation Association Activated


Error Message ASSOC_MGR-6-ASSOC_CREATED: Association Created for vlan id:[dec] vsan id:[dec]

Explanation Association Created


Error Message ASSOC_MGR-6-ASSOC_DEACTIVATED: Association Deactivated for vlan id: [dec] vsan id: [dec]

Explanation Association Deactivated


Error Message ASSOC_MGR-6-ASSOC_DELETED: Association Deleted for vlan id: [dec] vsan id: [dec]

Explanation Association Deleted


Error Message ASSOC_MGR-6-ASSOC_MGR_STATEFULL_RESTART: Association Manager Statefull Restart

Explanation Association Manager Stateful Restart


Error Message ASSOC_MGR-6-ASSOC_MGR_STATELESS_RESTART: Association Manager Stateless Restart

Explanation Association Manager Stateless Restart


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message ASSOC_MGR-6-ASSOC_OPER_STATUS_CHG: Association status for vlan id: [dec] vsan id: [dec] changed from [chars] to [chars]

Explanation Association Operational State Change


Error Message ASSOC_MGR-6-INFO_MSG: [chars]

Explanation ASSOC Manager Informational Message


ASSOC_MGR-7

Error Message ASSOC_MGR-7-DEBUG_MSG: [chars]

Explanation Association Manager Debug Message


BFDC MessagesThis section contains the BFDC messages.

BFDC-SLOT#-2

Error Message BFDC-SLOT#-2-BFDC_GENERAL_FAILURE: General failure. [chars]

Explanation General failure. This is a critical failure


Error Message BFDC-SLOT#-2-BFDC_MALLOC_FAILED: Memory allocation failed. [chars]

Explanation Memory allocation failed. This is a critical failure


Error Message BFDC-SLOT#-2-BFDC_MTS_FAILURE: MTS failure. [chars]

Explanation MTS related failure. This is a critical failure


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyBFD MessagesThis section contains the BFD messages.

BFD-3

Error Message BFD-3-SESSION_ACL_INSTALL_GAVE_UP: BFD session [chars] installation failed due to ACL installation failure interface [chars]

Explanation BFD session [chars] installation failed due to ACL installation failure interface [chars

Recommended Action Maximum acl install retries exceeded. Please to free up acl resources

Error Message BFD-3-SESSION_ACL_REMOVE_GAVE_UP: BFD session [chars] removal failed due to ACL removal failure interface [chars]

Explanation BFD session [chars] removal failed due to ACL removal failure interface [chars

Recommended Action Maximum acl removal retries exceeded. Please manually remove bfd sessions

Error Message BFD-3-SESSION_CREATE_FAIL: Failed to create BFD session to neighbor [chars] over intertface [chars]. Reason [chars]

Explanation Failed to create BFD session to neighbor [chars] over intertface [chars] Reason [chars]

Recommended Action SYSLOGDPC_NO_ACTION

BFD-4

Error Message BFD-4-INVALID_NBR: Attempt to register BFD session on invalid neighbor: [chars], by application=[chars]

Explanation Attempt to register BFD session on invalid neighbor: [chars] type that is not supported by BFD for application [chars].


Error Message BFD-4-SESSION_DELETE_FAIL: Attempt to delete BFD session [chars] failed: Reason [chars] ([hex]).

Explanation Attempt to delete [dec] BFD session[chars] failed: Reason [chars] ([hex]).


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyBFD-5

Error Message BFD-5-BFD_DISABLED: BFD Disabled

Explanation BFD Service Disabled


Error Message BFD-5-BFD_ENABLED: BFD Enabled

Explanation BFD Service nabled


Error Message BFD-5-BFD_SESSION_ADD: BFD session [hex] added



Error Message BFD-5-BFD_SESSION_DOWN: BFD session [hex] down



Error Message BFD-5-BFD_SESSION_REM: BFD session [hex] removed



Error Message BFD-5-BFD_SESSION_UP: BFD session [hex] up



BFD-6

Error Message BFD-6-SESSION_ACL_INSTALL_FAILED: BFD session [chars] failed due to missing ACL resources for interface [chars]

Explanation BFD session [chars] failed due to missing ACL resources for interface [chars]


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message BFD-6-SESSION_ACL_REMOVE_FAILED: BFD session [chars] removal failed due to missing ACL resources for interface [chars]

Explanation BFD session [chars] removal failed due to missing ACL resources for interface [chars]


Error Message BFD-6-SESSION_CREATED: BFD session to neighbor [chars] on interface [chars] has been created

Explanation BFD session to neighbor [chars] on interface [chars]


Error Message BFD-6-SESSION_LOCAL_PARAMS_CHANGE: Local parameter of BFD session [chars] has changed: [chars]

Explanation Local parameter of BFD session [chars] has changed: [chars]


Error Message BFD-6-SESSION_MOVED: BFD session [chars] has moved from [chars] to [chars]

Explanation BFD session [chars] has moved from [chars] to [chars]


Error Message BFD-6-SESSION_NO_RESOURCES_CLR: Lack of resources condition has cleared for session to neighbor [chars] on interface [chars]

Explanation Lack of resources condition has cleared for session to neighbor [chard] on interface [char].


Error Message BFD-6-SESSION_NO_RESOURCES: No resource for session to neighbor [chars] on interface [chars]

Explanation The BFD session can not be created or modified due to lack of resources. No resources for session to neighbor [chars]

Recommended Action Remove other BFD sessions to free resources for this session

Error Message BFD-6-SESSION_REMOVED: BFD session to neighbor [chars] on interface [chars] has been removed

Explanation BFD session to neighbor [chars] on interface [chars]


OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyError Message BFD-6-SESSION_STATE_DOWN: BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex].

Explanation BFD session [chars] to neighbor [chars] on interface [chars] has gone down. Reason: [hex]. This may be as a result of the forwarding path being down.


Error Message BFD-6-SESSION_STATE_UP: BFD session [chars] to neighbor [chars] on interface [chars] is up.

Explanation BFD session [chars] to neighbor [chars] on interface [chars] is up.


BIOS DAEMON MessagesThis section contains the BIOS DAEMON messages.

BIOS DAEMON-2

Error Message BIOS_DAEMON-2-BIOS_DAEMON_FLASH_WARNING: Flash chip not supported by running image. Skipping bios upgrade.

Explanation BIOS CHIP NOT SUPPORTED


Error Message BIOS_DAEMON-2-BIOS_DAEMON_PRI_BOOT_FAIL: System booted from Alternate BIOS Flash

Explanation Boot from Alternate

Recommended Action SYSLOGDOC_NOACTION

Error Message BIOS_DAEMON-2-BIOS_DAEMON_SUP_ERROR: BIOS Sector ([dec]) is write protected

Explanation BIOS WRITE PROTECTED

Recommended Action Please contact the Cisco reseller through which you procured the product for support. If you have purchased a Cisco support contract please call Cisco TAC for support. 2-28Nexus 5000 Series NX-OS System Message Reference

OL-25078-01


Chapter 2 System Messages and Recovery Procedures for the Cisco Nexus 5000 FamilyBIOS_DAEMON-5

Error Message BIOS_DAEMON-5-BIOS_DAEMON_PRI_BOOT: System booted from Primary BIOS Flash

Explanation Boot from Primary

Recommended Action SYSLOGDOC_NOACTION

BIOS_DAEMON-SLOT#-2

Error Message BIOS_DAEMON-SLOT#-2-BIOS_DAEMON_LC_ERROR: BIOS Sector ([dec]) is write protected

Explanation BIOS WRITE PROTECTED

Recommended Action Please contact the Cisco reseller through which

Nexus 5000 Errors

Documents

Transcript of Nexus 5000 Errors