New Jefferson Office Park · 2010. 10. 9. · Preliminary Jefferson Office Park 1020 Johnson Road...
Transcript of New Jefferson Office Park · 2010. 10. 9. · Preliminary Jefferson Office Park 1020 Johnson Road...
Prelimina
ry
Jefferson Office Park
1020 Johnson Road
Golden, Colorado 80219
Exit Width Required: Third Floor: Business Group B Egress width per occupant served w/ sprinkler system per Table 1005.1 = 0.2 in./occupant (Stairway) 100 occupants x 0.2 in./occupant = 20” Second Floor: Business Group B Egress width per occupant served w/ sprinkler system per Table 1005.1 = 0.2 in./occupant (Stairway) 100 occupants x 0.2 in./occupant = 20” First Floor: Business Group B Egress width per occupant served w/ sprinkler system per Table 1005.1 = 0.15 in./occupant (Other egress components) 200 occupants from second and third floors and 100 occupants from first floor = 300 occupants 300 occupants x 0.15 in./occupant = 45”
Exits Required: Third Floor: Business Group B 2 exits required where occupant load exceeds 49 for Business Group B occupancy per Table 1015.1 and less than 500 per Table 1019.1 Third floor occupant load = 100 occupants 49 occ. < 100 occ. < 500 occ. = 2 exits required Second Floor: Business Group B 2 exits required where occupant load exceeds 49 for Business Group B occupancy per Table 1015.1 and less than 500 per Table 1019.1 Second floor occupant load = 100 occupants 49 occ. 100 occ. < 500 occ. = 2 exits required First Floor: Business Group B Tenant Space 100 1 exit permitted when occupant load is less than 49 for Business Group B occupancy per Table 1015.1 Tenant Space 100 occupant load = 40 40 occ. < 49 occ. = 1 exit required Tenant Space 180 1 exit permitted when occupant load is less than 49 for Business Group B occupancy per Table 1015.1 Tenant Space 180 occupant load = 41 41 occ. < 49 occ. = 1 exit required Accessory Area 2 exits required where occupant load exceeds 49 for Business Group B occupancy per Table 1015.1 and less than 500 per Table 1019.1 Accessory Area occupant load = 300 49 occ. 300 occ. < 500 occ. = 2 exits required
Exits Provided: Third Floor: Business Group B 2 exits provided, total exit width provided = 72” Second Floor: Business Group B 2 exits provided, total exit width provided = 72” First Floor: Business Group B Tenant Space 100 5 exits provided, total exit width provided = 288” Tenant Space 180 5 exits provided, total exit width provided = 288” Accessory Area 2 exits provided, total exit width provided = 108”
Plumbing Fixtures: First Floor: Male: 100 occupants/2 = 50 males(Business Class.) Water Closets: 1/25 for first 50 males
1 water closet and 1 urinal provided Lavatories: 1/40 for first 80 males 2 lavatories provided Female: 100 occupants/2 = 50 females Water Closets: 1/25 for first 50 females 2 water closets provided Lavatories: 1/40 for first 80 males 2 lavatories provided Drinking Fountains: 1/100 occupants 2 drinking fountains provided (1 accessible) Service Sinks: 1 required 1 mop sink provided Second Floor: Same as First Floor Third Floor: Same as First Floor
Allowable Floor Area: w/o Area Modifications (per Table 503): Business Group B, Type V-B Construction 2 stories w/ maximum height of 40’ 9,000 sq. ft. per story 18,000 sq. ft. total building area
w/ Area Modifications: Frontage increase (per Sec. 506.2): If = (F/P - 0.25) W/30 F = 418’-8” or 418.67’, P = 418’-8” or 418.67’, W > 30’ If = (418.67’/418.67’ - 0.25) 30’/30’ = 0.75 Automatic sprinkler system increase (per Sec. 504.2): 3 stories w/ maximum height of 60’ Automatic sprinkler system increase (per Sec. 506.3): Allowable area increase per story of 200% (Is = 2) Allowable area per story w/o automatic sprinkler system increase: At = 9,000 sq. ft., If = .75 Aa = At + (At x If) Aa = 9,000 sq. ft. + (9,000 sq .ft. x. 75) Aa = 9,000 sq. ft. + 6,750 sq. ft. Aa = 15,750 sq. ft. per story Allowable floor area w/o automatic sprinkler system increase: Aa = 15,750 sq. ft. per story 15,750 sq. ft. x 3 = 47,250 sq. ft. total building area Allowable area per story w/ automatic sprinkler system increase: At = 9,000 sq. ft., If = .75, Is = 2 Aa = At + (At x If) + (At x Is) Aa = 9,000 sq. ft. + (9,000 sq. ft. x .75) + (9,000 sq. ft. x 2) Aa = 9,000 sq. ft. + 6,750 sq. ft. + 18,000 sq. ft. Aa = 33,750 sq. ft. per story Allowable floor area w/ automatic sprinkler system increase: Aa = 33,750 sq. ft. per story 33,750 sq. ft. x 3 = 101,250 sq. ft. total building area
Actual Floor Area: First Floor ………………. 10,030 sq. ft. Second Floor …………… 10,030 sq. ft. Third Floor ……………… 10,030 sq. ft. Total Actual Floor Area 30,090 sq. ft.
Occupant Load: Third Floor: Business Group B Occupant load factor — Business areas per Table 1004.1.1 = 100 gross sq. ft./occupant Floor area = 10, 030 gross sq. ft. 10,030 gross sq. ft./(1 occupant/100 gross sq. ft.) = 100.3 occupants, use 100 occupants Second Floor: Business Group B Occupant load factor — Business areas per Table 1004.1.1 = 100 gross sq. ft./occupant Floor area = 10, 030 gross sq. ft. 10,030 gross sq. ft./(1 occupant/100 gross sq. ft.) = 100.3 occupants, use 100 occupants First Floor: Business Group B: Occupant load factor - Business areas per Table 1004.1.1 = 100 sq.ft./occupant Tenant Space 100 floor area = 4,023 gross sq. ft. 4,023 gross sq. ft./(1 occupant/100 gross sq. ft.) = 40.02 occupants, use 40 occupants Tenant Space 180 floor area = 4,102 gross sq. ft. 4,102 gross sq. ft./(1 occupant/100 gross sq. ft.) = 41.02 occupants, use 41 occupants Accessory Area floor area = 1,905 gross sq. ft. 1,905 gross sq. ft./(1 occupant/100 gross sq. ft.) = 19.05 occupants, use 19 occupants Total first floor occupants = 100 occupants Total Building: 300 occupants
CODE ANALYSIS
Regulatory Agencies: City of Golden Planning & Development Department, 303.384.8097 Steve Glueck, Planning & Development Director, 303.384.8095 City of Golden Building Department, 303.384.8151 Gerald George, Chief Building Official, 303.384.8147 City of Golden Fire Department, 303.384.8094 Jerry Stricker, Fire Marshal, 303.384.8093 City of Golden Engineering Department, 303.384.8151 Vince Auriemma, City Engineer, 303.384.8156
Applicable Codes: International Building Code, 2006 Edition Accessible and Usable Buildings and Facilities, ICC/ANSI A117.1-2003 ADA Accessibility Guidelines for Buildings and Facilities International Fire Code, 2006 Edition International Energy Conservation Code, 2006 Edition International Mechanical Code, 2003 Edition International Plumbing Code, 2003 Edition International Fuel Gas Code, 2006 Edition National Electrical Code, 2005 Edition
Project Type: New three story office building
Address: 1030 Johnson Road, Golden, CO 80401
Legal Description: A PORTION OF LOT 1, BLOCK 1, GOLDEN DEVELOPMENT SITESUBDIVISION, AS RECORDED IN THE RECORDS OF JEFFERSONCOUNTY, COLORADO IN BOOK 98 AT PAGE 47, RECEPTION NO.88093385, DESCRIBED AS FOLLOWS:
BEGINNING AT THE SOUTHWEST CORNER OF SAID LOT 1; THENCENORTH 89 DEGREES 58 MINUTES 30 SECONDS EAST ALONG THESOUTH LINE OF SAID LOT 1, A DISTANCE OF 419.55 FEET TO THESOUTHEAST CORNER OF SAID LOT 1; THENCE NORTHERLY ALONG THE EAST LINE OF SAID LOT1, THE FOLLOWING TWO (2)COURSES:
1) NORTH 01 DEGREES 03 MINUTES 30 SECONDS EAST,391.39 FEET;
2) THENCE NORTH 00 DEGREES 04 MINUTES 14 SECONDSEAST, 172.68 FEET, MORE OR LESS, TO A POINT FROMWHICH THE NORTHEAST CORNER OF SAID LOT 1 BEARSNORTH 00 DEGREES 04 MINUTES 14 SECONDS EAST,552.06 FEET;
THENCE NORTH 89 DEGREES 39 MINUTES 15 SECONDS WEST BEING PARALLEL WITH THE NORTH LINE OF SAID LOT 1, A DISTANCE OF 557.34 FEET; THENCE SOUTH 63 DEGREES 38
MINUTES 50 SECONDS WEST (RADIAL LINE), 169.22 FEET TO THEWEST LINE OF SAID LOT 1; THENCE SOUTHEASTERLY ALONG SAIDWEST LINE, THE FOLLOWING TWO (2) COURSES:
1) SOUTHEASTERLY ALONG A CURVE TO THE LEFT, THETANGENT OF WHICH BEARS SOUTH 26 DEGREES 21MINUTES 10 SECONDS EAST, HAVING A RADIUS OF 450.00FEET, A CENTRAL ANGLE OF 21 DEGREES 40 MINUTES 03SECONDS, FOR A DISTANCE OF 170.18 FEET TO APOINTOF REVERSE CURVE;
2) THENCE SOUTHEASTERLY ALONG A CURVE TO THERIGHT, HAVING A RADIUS OF 550.00 FEET, A CENTRALANGLE OF 42 DEGREES 40 MINUTES 45 SECONDS FOR ADISTANCE OF 409.69 FEET TO THE POINT OF BEGINNING,COUNTY OF JEFFERSON, STATE OF COLORADO.
Zoning Designation: PUD
Occupancy Group: Business Group B
Site Area: 64,830 sq. ft. or 7.03 acres
Construction Type: V-B (Sprinkled)
Location on Site: North: 90.60’ from N property line East: 363.36’ from E property line, 135.00’ from future bldg. South: 355.06’ from S property line (W. 10th Ave.), 39.00’ from future bldg. West: 115.06’ from E property line (Johnson Rd.)
Sheet Index
Cover SheetCivil Sheets:
Cover SheetHorizontal Control PlanInitial Erosion Control PlanInterim Erosion Control PlanPhase 1 Final Erosion Control PlanErosion Control DetailsErosion Control Details and NotesOverlot Grading PlanFinish Grading PlanOverall Utility PlanDrainage Outfall Plan and ProfileStorm Drain Plan and Profile - NorthStorm Drain Plan and Profile - CenterStorm Drain Plan and Profile - SouthSanitary Sewer Plan and ProfilePost Office Drive ModificationsDetailsDetails
Landscaping: L1 Landscape Notes & Details L2 Landscape Plan
Architectural:A1 1st Floor PlanA2 2nd Floor PlanA3 3rd Floor PlanA4 Roof PlanA5 1st Floor Core Plan & Toilet Room ElevationsA6 Second & Third Floor Core PlansA7 Reflected Ceiling PlansA8 Finish & Door Schedules; Door Frame &
Window TypesA9 Exterior ElevationsA10 Building SectionsA11 Stair Section & Core Wall SectionA12 Core Wall DetailsA13 Core Wall Details & Typical Wall Sections
Structural:S1.0 Cover DetailsS2.0 Foundation PlanS2.1 Second Level Framing PlanS2.2 Third Level Framing PlanS2.3 Roof Framing PlanS3.0 Foundation DetailsS3.1 Framing DetailsS3.2 Framing DetailsS3.3 Framing DetailsS4.0 Frames/Columns Schedule
Mechanical:M1.1 HVAC SchedulesM2.1 First Floor Plan – HVACM2.2 Second Floor Plan – HVACM2.3 Third Floor Plan – HVACM2.4 Roof Plan – HVACM3.1 HVAC Details
Plumbing:P1.1 Plumbing SchedulesP2.0 Underslab Plan – PlumbingP2.1 First Floor Plan – PlumbingP2.2 Second Floor Plan – PlumbingP2.3 Third Floor Plan – PlumbingP2.4 Roof Plan – PlumbingP3.1 Plumbing Details
Electrical:E1 Electrical Site PlanE2 Notes & LegendE3 One-Line DiagramE4 Panel Schedules & Lighting Fixture ScheduleE5 First Floor Power & Lighting PlansE6 Second Floor Power & Lighting PlansE7 Third Floor Power & Lighting PlansE8 Roof Power Plan
Contacts
Owner:Jefferson Office Park L.L.L.P.12 Ward Ct.Lakewood, CO 80228303.482.1809 telephone303.723.5503 [email protected]
General Contractor:Golden Builders, Inc.195 S. Union Blvd. Suite 180Lakewood, CO 80228303.482.1809 telephone303.459.7929 [email protected]
Architect:Joe Haezebrouck, RA, NCARBHaezebrouck & Associates, P.C.1543 Sunset Ridge RoadHighlands Ranch, CO 80126-2681303.470.7872 telephone303.470.7874 facsimile303.880.2246 [email protected]
CAD Consultant:Doug Forry10251 S. Nickolas Ave.Highlands Ranch, CO 80130303.482.1809 telephone303.723.5503 [email protected]
Mechanical Engineer:Peter F. McDonald, PEMcDonald Consulting + Design10698 Amesbury WayHighlands Ranch, CO 80126303.875.9293 telephone303.346.8549 [email protected]
Electrical Engineer:Dave Kazin, PEKazin & Associates5031 S. Ulster St., Ste. 160Denver, CO 80237720.489.1609 #1 telephone720.489.1611 [email protected]
Structural Engineer:Stan Neujahr, PENeujahr & Gorman80 Steele St. #200Denver, CO 80206303.377.2732 telephone303.377.4573 [email protected]
Specification Consultant:Warren FosterConstruction Specification Specialist LTD.16428 W. First Ave.Golden, CO. 80401303.216.9560 telephone303.216.9566 [email protected]
Office Building Type 3
General Notes
1. Prior to starting construction, the General Contractor shall obtain all permits requiredby regulatory authorities. No construction or fabrication of any item should begin untilthe General Contractor has received all documentation from regulatory authorities.Failure of the General Contractor to follow this procedure shall cause the GeneralContractor to assume full responsibility for subsequent modifications of workmandated by regulatory authorities.
2. The General Contractor shall be responsible for providing all materials andworkmanship in accordance with all Federal, State and Local codes, laws, ordinancesand regulations applicable to this project.
3. Do not scale any drawings. The Contractor shall verify all dimensions prior to the startof construction and notify the Architect of any discrepancies so that the design may bereevaluated.
4. Dimensions shall be to either the centerline of a column; edge or face of steel studframing; face of concrete or masonry wall; extent of a finish, location of or clearancerequired for a fixture; centerline of exposed tee ceiling grid or light fixture; edge ofdoor, door light or aluminum storefront framing; floor, roof or parapet line; top orbottom of doors, windows and pilasters unless noted otherwise.
5. The General Contractor shall coordinate the work to be completed by all trades.6. The General Contractor shall verify the location of all utilities, connect the secondary
utility lines from the building to the primary service location, unless directed otherwiseby the utility having jurisdiction. The General Contractor shall be responsible for allfees related to such work.
7. The General Contractor shall maintain a clean construction site and remove allconstruction debris from the site. The Contractor shall provide dumpsters, or othermeans of trash disposal, on site as needed for the timely removal of trash and debris.
8. Refer to Wall Types for specific wall construction.9. Refer to the Door and Window Schedules for general door, hardware and window
specifications. Refer to Finish Schedule for general floor, wall and ceiling finishspecifications.
10. Fire alarm and sprinkler systems, security systems, or other similar systems, and anyengineering required for these systems, if required by the governing jurisdiction orBuilding Owner, shall be the responsibility of and be coordinated by the GeneralContractor.
11. The General Contractor shall be responsible for and coordinate the buildingcommunication and cable service requirements with the Building Owner.
12. The General Contractor shall provide fire extinguishers in recessed cabinets, of thetype and in the locations required by the Fire Protection District and selected by theArchitect.
13. The General Contractor shall coordinate and provide a complete and finished projectas shown on the Architectural, Structural, Mechanical, Plumbing and Electricaldrawings.
14. THE AMERICANS WITH DISABILITIES ACT: The Americans with Disabilities Act (ADA) requires the removal of architectural barriersin existing and new facilities where such removal is “readily achievable”. The BuildingOwner acknowledges that the definition of “readily achievable” as contained in theADA is flexible and subject to interpretation on a case-by-case basis. Therequirements of the ADA will therefore be subject to various and possible contradictoryinterpretations. The Architect shall use reasonable professional efforts and judgmentto interpret and incorporate applicable ADA requirements, and advise the BuildingOwner regarding modifications to the Building Owner’s facility space that may berequired in order to comply with the ADA. Such interpretation and advice shall bebased upon what is known about the ADA at the time that professional service isrendered. The Architect however, cannot and does not warrant or guarantee that theBuilding Owner’s facility will fully comply with interpretations of the ADA requirementsrendered by regulatory authorities or court decisions.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
CS
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
1 2
2
2
1
1
12
2
2
1
1
22
2 11 2
2 2
11
6A
11
6A
113A113A
114A114A
115A115A
1
2
3
4
5
6
7
8
9
A B C D E F G H J K
A
DB
A B
D
D
DD
DD
E
B
B
A
G
G
H
M
H
LK
K
K
J
J
D D
D D
F
R
R
F
F
E
F
E
N
N
G
G
K
K
1A11
3'-
4"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
4"
3'-4"8"
12'-8"8"
3'-0" 8" 16'-10" 8"3'-4"
8"16'-10"
8"3'-0"
8"12'-8"
8"3'-0"
8"16'-10"
8"
3'-4"8" 16'-10"
8"3'-0"
8"12'-8"
8"3'-4"
45/8" 65/8"37'-63/4"
45/8" 65/8"22'-23/4"
35/8"8'-11/4"
35/8"
1'-61/4"
35/8"5'-11/4"
35/8"23'-63/4"
65/8" 45/8"37'-63/4"
65/8" 45/8"
41
/1
6"
65
/8
"5
'-1
1/
4"
35
/8
"2
3'-
61
/2
"2
9'-
6"
21
'-7
3/
4"
35
/8
"7
'-0
" 65
/8
"4
5/
8"
45/8" 65/8"23'-63/4"
35/8"14'-0"
35/8"23'-63/4"
65/8" 45/8"
38'-6" 63'-71/4" 38'-6"
38'-6" 63'-71/4" 38'-6"
140'-71/4"
4'-
4"
80
'-7
1/
4"
4'-
4"
89
'-3
1/
4"
45
/8
"6
5/
8"
3'-
93
/8
"
65
/8
"
24
'-7
3/
8"
29
'-6
"2
4'-
73
/8
"
65
/8
"
3'-
93
/8
"
65
/8
"4
5/
8"
3'-
4"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
4"
4'-
4"
80
'-7
1/
4"
4'-
4"
89
'-3
1/
4"
3'-4" 8" 12'-8" 8"3'-0"
8" 16'-10"8"
3'-4" 8" 16'-10" 8" 3'-0"8"
12'-8"8"
3'-0" 8" 16'-10" 8" 3'-4" 8" 16'-10" 8" 3'-0" 8" 12'-8" 8" 3'-4"
140'-71/4"
81/4" 35'-6" 3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7" 39'-0" 81/4"
81
/4
"4
'-4
"1
8'-
53
/8
"1
1'-
83
/8
"9
'-5
5/
8"
9'-
55
/8
"1
1'-
83
/8
"1
8'-
53
/8
"4
'-4
"8
1/
4"
1A9
2A9
3A10
4A10
11,715 sq ft Scale: 1/8" = 1'-0"Gross Floor Area -
First Floor Plan
North
Co
rrid
or
11
5
FireSprinkler
116
Lobby113
Foyer114
TenantSpace
100
TenantSpace
180
UP
UP
UP
UP
2A11
2A11
1A11
1A11
K
1A5
45/8" 65/8"34'-915/16" 57'-1113/16" 45'-11"
65/8" 45/8"
Wall TypesA Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylic
elastomeric finish coat over acrylic primer coat over 3/8” thick factory mixed cementitious one-coat stuccowith acrylic polymer admixture over 2.5 lb./sq. yd. self-furring diamond mesh metal lath over TyvekCommercialWrap D over 5/8” exterior grade gypsum board sheathing. Insulate wall with R-19 FSK-facedflame spread 25 fiberglass insulation. Fill holes at duplexes, switches and other voids with expandingfoam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping whererequired per Sec. 717, 2006 IBC. Finish gypsum board below ceiling height with Level 5 finish. Finishinterior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenant finish. Forwindow assembly refer to Window Schedule and Window Types on sheet A10.
B Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with 4”nom. brick veneer pilaster over 7/8” air space over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time oftenant finish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board below ceiling height with Level 5 finish.
C Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylicelastomeric finish coat over fiberglass reinforcing mesh embedded in 1/16” — 3/32” thick acrylic polymermodified cementitious base coat over 2” thick expanded polystyrene insulation (EPS) adhered with abovebase coat to 3/8” thick factory mixed cementitious one-coat stucco with acrylic polymer admixture over 2.5lb. /sq. yd. self-furring diamond mesh metal lath over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Back wrap all EPS shapes with fiberglass reinforcing mesh. Do not lap meshover one-coat stucco. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fill holesat duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenantfinish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsumboard below ceiling height with Level 5 finish.
D Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish common area side of wall with 5/8” type “x” gypsum board to undersideof floor or roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum boardbelow ceiling height with Level 5 finish. Finish tenant side of wall with 5/8” type “x” gypsum board tounderside of floor or roof deck at time of tenant finish.
E Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish both faces of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board on Corridorside of wall below ceiling height with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side ofwall with Level 2 finish.
F Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish both faces of wall with 5/8”type “x” gypsum board to underside of beam, floor or roof deck above. Insulate wall with 3-1/2” soundattenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed to maintainthe fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board below ceilingheight with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side of wall with Level 2 finish.
G Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, diagonal brace or roof deck above with slip joint at top of wall. Finish face of wall with5/8” type “x” gypsum board to underside of floor or roof deck above. Insulate tenant side of wall with 3-1/2”sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed tomaintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onStair side of wall below ceiling height with Level 5 finish. Finish gypsum board on Tenant side of wallbelow ceiling height with Level 5 finish. Finish gypsum board on Mech. Shaft side of wall with Level 1finish.
H Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Fill holes at duplexes, switches and other voids with expanding foam sealant thatcomplies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717,2006 IBC. Finish gypsum board below ceiling height with Level 5 finish.
J Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate Toilet Room side of wall with 3-1/2” sound attenuation battinsulation. Fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
K Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam, floor or roof deckabove with slip joint at top of wall. Finish face of Toilet Room and Janitor Closet side of walls with 5/8” type“x” moisture resistant gypsum board to underside of beam, floor or roof deck above. Finish face of corridorside of walls with 5/8” type “x” gypsum board to underside of beam, floor or roof deck above. Insulate toiletroom side of wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes, switches and othervoids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking anddraftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board above tile wainscot and belowceiling height in Toilet Rooms with Level 5 finish. Finish gypsum board behind tile wainscot in Toilet Roomsand behind fiberglass reinforced plastic panels (FRP) in Janitor Closet with Level 2 finish. Refer to ToiletRoom Elevations on sheet A5.
L Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Janitor Closet sideof wall with 5/8” type “x” moisture resistant gypsum board to underside of beam, floor or roof deck above.Finish face of Stair side of wall with 5/8” type “x” gypsum board to underside of beam, floor or roof deckabove. Insulate wall with 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessedfixtures shall be installed to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Wherepermitted fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board on Stair side of wall with Level 5 finish. Finish gypsum board on Janitor side of wallbehind fiberglass reinforced plastic panels with Level 2 finish.
M Interior wall from 6” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck above withslip joint at top of wall. Finish both faces of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate wall with 2 layers 3-1/2” sound attenuation batt insulation.Fill holes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
N Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam above with slip joint at top of wall. Finish face of Elevator side of wall with 1” gypsumboard liner panels to underside of beam above. Finish face of Corridor, Communications and ElevatorEqpt. Room side of wall with 5/8” type “x” gypsum board to underside of beams above. Finish face of Stairside of wall with 5/8” type “x” gypsum board. Insulate wall with 3-1/2” sound attenuation batt insulation.Through wall penetrations and recessed fixtures shall be installed to maintain the fire resistive rating of thewall per Section 712, 2006 IBC. Where permitted fill holes at duplexes, switches and other voids withexpanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstoppingwhere required per Sec. 717, 2006 IBC. Finish gypsum board on Corridor and Stair side of wall with Level5 finish. Finish gypsum board on Communications and Elevator Eqpt. Room side of wall with Level 2finish.
P Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam or roof deck above with slip joint at top of wall. Finish face of Mech. Shaft side ofwall with 1” gypsum board liner panels to underside of beam or roof deck above. Finish face of Tenantside of wall with 5/8” type “x” gypsum board to underside of beam or roof deck above. Insulate wall with3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installedto maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onTenant side of wall with Level 5 finish.
R Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Stair side ofwall with 5/8” type “x” gypsum board to underside of roof deck above. Finish face of Tenant side ofwall with 2 layers 5/8” type “x” gypsum board to underside of floor or roof beam above. Insulate wallwith 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall beinstalled to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec.2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board below ceiling height with Level 5 finish.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A1
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inaryN
1
2
3
4
5
6
7
8
9
A B C D E F G H J K
1A6
1A9
2A9
3A10
4A10
3'-3"8"
12'-8"8"
3'-0"8"
16'-10"9"
3'-3"8"
16'-10"8"
3'-0"8"
12'-8"8"
3'-0"8"
16'-10"8"
3'-3"9"
16'-10"8"
3'-0"8"
12'-8"8"
3'-3"
38'-6" 62'-10" 38'-6"
139'-10"
3'-
3"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
3"
4'-
4"
79
'-1
0"
4'-
4"
88
'-6
"
35
/8
"4
'-4
"1
8'-
53
/8
"1
1'-
83
/8
"9
'-5
5/
8"
9'-
55
/8
"1
1'-
83
/8
"1
8'-
53
/8
"4
'-4
"3
5/
8"
11,736 sq ft Scale: 1/8" = 1'-0"Gross Floor Area -
Second Floor Plan
North
TenantSpace
200
TenantSpace
220
DN
UP
UP
DN
UP
UP
2A11
2A11
3'-3"8"
12'-8"8"
3'-0"8"
16'-10"9"
3'-3"8"
16'-10"8"
3'-0"8"
12'-8"8"
3'-0"8"
16'-10" 8"3'-3" 9"
16'-10"8"
3'-0"8"
12'-8"8"
3'-3"
38'-6" 62'-10" 38'-6"
139'-10"
3'-
3"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
3"
65/8" 32'-33/16" 63'-15/16" 43'-41/4" 65/8"
65/8"37'-113/8"
65/8"61'-83/4"
65/8"37'-113/8"
65/8"
65/8"37'-113/8"
65/8"61'-83/4"
65/8"37'-113/8"
65/8"
4'-
4"
79
'-1
0"
4'-
4"
88
'-6
"
1A11
1A11
21
1
1
2
2
1
1
2
2
22 1
2 1
2 1
2 21
21
A
C
A C
C
C
A
G
G
K
M
K
L
K
K
J
J
D D
D D
P
R
R
F
F
E
E
F
EP
P
P
P
P
K
K
N
65
/8
"3
'-9
3/
8" 6
5/
8"
24
'-7
3/
8"
29
'-6
"2
4'-
73
/8
"
65
/8
"3'-
93
/8
"
65
/8
"
35/8" 35'-6" 3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7" 39'-0" 35/8"
Wall TypesA Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylic
elastomeric finish coat over acrylic primer coat over 3/8” thick factory mixed cementitious one-coat stuccowith acrylic polymer admixture over 2.5 lb./sq. yd. self-furring diamond mesh metal lath over TyvekCommercialWrap D over 5/8” exterior grade gypsum board sheathing. Insulate wall with R-19 FSK-facedflame spread 25 fiberglass insulation. Fill holes at duplexes, switches and other voids with expandingfoam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping whererequired per Sec. 717, 2006 IBC. Finish gypsum board below ceiling height with Level 5 finish. Finishinterior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenant finish. Forwindow assembly refer to Window Schedule and Window Types on sheet A10.
B Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with 4”nom. brick veneer pilaster over 7/8” air space over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time oftenant finish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board below ceiling height with Level 5 finish.
C Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylicelastomeric finish coat over fiberglass reinforcing mesh embedded in 1/16” — 3/32” thick acrylic polymermodified cementitious base coat over 2” thick expanded polystyrene insulation (EPS) adhered with abovebase coat to 3/8” thick factory mixed cementitious one-coat stucco with acrylic polymer admixture over 2.5lb. /sq. yd. self-furring diamond mesh metal lath over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Back wrap all EPS shapes with fiberglass reinforcing mesh. Do not lap meshover one-coat stucco. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fill holesat duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenantfinish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsumboard below ceiling height with Level 5 finish.
D Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish common area side of wall with 5/8” type “x” gypsum board to undersideof floor or roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum boardbelow ceiling height with Level 5 finish. Finish tenant side of wall with 5/8” type “x” gypsum board tounderside of floor or roof deck at time of tenant finish.
E Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish both faces of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board on Corridorside of wall below ceiling height with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side ofwall with Level 2 finish.
F Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish both faces of wall with 5/8”type “x” gypsum board to underside of beam, floor or roof deck above. Insulate wall with 3-1/2” soundattenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed to maintainthe fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board below ceilingheight with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side of wall with Level 2 finish.
G Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, diagonal brace or roof deck above with slip joint at top of wall. Finish face of wall with5/8” type “x” gypsum board to underside of floor or roof deck above. Insulate tenant side of wall with 3-1/2”sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed tomaintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onStair side of wall below ceiling height with Level 5 finish. Finish gypsum board on Tenant side of wallbelow ceiling height with Level 5 finish. Finish gypsum board on Mech. Shaft side of wall with Level 1finish.
H Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Fill holes at duplexes, switches and other voids with expanding foam sealant thatcomplies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717,2006 IBC. Finish gypsum board below ceiling height with Level 5 finish.
J Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate Toilet Room side of wall with 3-1/2” sound attenuation battinsulation. Fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
K Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam, floor or roof deckabove with slip joint at top of wall. Finish face of Toilet Room and Janitor Closet side of walls with 5/8” type“x” moisture resistant gypsum board to underside of beam, floor or roof deck above. Finish face of corridorside of walls with 5/8” type “x” gypsum board to underside of beam, floor or roof deck above. Insulate toiletroom side of wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes, switches and othervoids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking anddraftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board above tile wainscot and belowceiling height in Toilet Rooms with Level 5 finish. Finish gypsum board behind tile wainscot in Toilet Roomsand behind fiberglass reinforced plastic panels (FRP) in Janitor Closet with Level 2 finish. Refer to ToiletRoom Elevations on sheet A5.
L Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Janitor Closet sideof wall with 5/8” type “x” moisture resistant gypsum board to underside of beam, floor or roof deck above.Finish face of Stair side of wall with 5/8” type “x” gypsum board to underside of beam, floor or roof deckabove. Insulate wall with 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessedfixtures shall be installed to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Wherepermitted fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board on Stair side of wall with Level 5 finish. Finish gypsum board on Janitor side of wallbehind fiberglass reinforced plastic panels with Level 2 finish.
M Interior wall from 6” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck above withslip joint at top of wall. Finish both faces of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate wall with 2 layers 3-1/2” sound attenuation batt insulation.Fill holes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
N Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam above with slip joint at top of wall. Finish face of Elevator side of wall with 1” gypsumboard liner panels to underside of beam above. Finish face of Corridor, Communications and ElevatorEqpt. Room side of wall with 5/8” type “x” gypsum board to underside of beams above. Finish face of Stairside of wall with 5/8” type “x” gypsum board. Insulate wall with 3-1/2” sound attenuation batt insulation.Through wall penetrations and recessed fixtures shall be installed to maintain the fire resistive rating of thewall per Section 712, 2006 IBC. Where permitted fill holes at duplexes, switches and other voids withexpanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstoppingwhere required per Sec. 717, 2006 IBC. Finish gypsum board on Corridor and Stair side of wall with Level5 finish. Finish gypsum board on Communications and Elevator Eqpt. Room side of wall with Level 2finish.
P Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam or roof deck above with slip joint at top of wall. Finish face of Mech. Shaft side ofwall with 1” gypsum board liner panels to underside of beam or roof deck above. Finish face of Tenantside of wall with 5/8” type “x” gypsum board to underside of beam or roof deck above. Insulate wall with3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installedto maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onTenant side of wall with Level 5 finish.
R Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Stair side ofwall with 5/8” type “x” gypsum board to underside of roof deck above. Finish face of Tenant side ofwall with 2 layers 5/8” type “x” gypsum board to underside of floor or roof beam above. Insulate wallwith 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall beinstalled to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec.2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board below ceiling height with Level 5 finish.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A2
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
21
1
2
2
11
1
2
2
22 1
2 1
2 1
2 21
21
N
N
1
2
3
4
5
6
7
8
9
A B C D E F G H J K
2A6
1A9
2A9
3A10
4A10
65/8" 37'-113/8" 65/8" 61'-83/4" 65/8" 37'-113/8" 65/8"
65
/8
"
3'-
93
/8
"
65
/8
"2
4'-
73
/8
"2
9'-
6"
24
'-7
3/
8"
65
/8
"
3'-
93
/8
"
65
/8
"
65/8" 32'-33/16" 63'-15/16" 43'-41/4" 65/8"
3'-3"8"
12'-8"8"
3'-0"8"
16'-10"9"
3'-3"8"
16'-10"8"
3'-0"8"
12'-8"8"
3'-0"8"
16'-10"8"
3'-3"9"
16'-10"8"
3'-0"8"
12'-8"8"
3'-3"
38'-6" 62'-10" 38'-6"
139'-10"
3'-
3"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
3"
4'-
4"
79
'-1
0"
4'-
4"
88
'-6
"
3'-
3"
8"
12
'-8
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
6'-
10
"8
"3
'-0
"8
"1
2'-
8"
8"
3'-
3"
4'-
4"
79
'-1
0"
4'-
4"
88
'-6
"
3'-3" 8" 12'-8" 8" 3'-0" 8" 16'-10" 9" 3'-3" 8" 16'-10" 8" 3'-0" 8" 12'-8" 8" 3'-0" 8" 16'-10" 8" 3'-3" 9" 16'-10" 8" 3'-0" 8" 12'-8" 8" 3'-3"
38'-6" 62'-10" 38'-6"
139'-10"
65/8" 37'-113/8" 65/8" 61'-83/4" 65/8" 37'-113/8" 65/8"
35/8" 35'-6" 3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7" 39'-0" 35/8"
35
/8
"4
'-4
"1
8'-
53
/8
"1
1'-
83
/8
"9
'-5
5/
8"
9'-
55
/8
"1
1'-
83
/8
"1
8'-
53
/8
"4
'-4
"3
5/
8"
2A11
2A11
11,736 sq ft
TenantSpace
300
TenantSpace
320
DN
UP
DN
DN
UP
1A11
1A11
A
C
A C
C
C
A
G
G
K
M
K
LK
KK
K
J
J
D D
D D
P
R
R
F
F
E
E
F
EP
P
P
P
P
Scale: 1/8" = 1'-0"Gross Floor Area -
Third Floor Plan
North
Wall TypesA Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylic
elastomeric finish coat over acrylic primer coat over 3/8” thick factory mixed cementitious one-coat stuccowith acrylic polymer admixture over 2.5 lb./sq. yd. self-furring diamond mesh metal lath over TyvekCommercialWrap D over 5/8” exterior grade gypsum board sheathing. Insulate wall with R-19 FSK-facedflame spread 25 fiberglass insulation. Fill holes at duplexes, switches and other voids with expandingfoam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping whererequired per Sec. 717, 2006 IBC. Finish gypsum board below ceiling height with Level 5 finish. Finishinterior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenant finish. Forwindow assembly refer to Window Schedule and Window Types on sheet A10.
B Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with 4”nom. brick veneer pilaster over 7/8” air space over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time oftenant finish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board below ceiling height with Level 5 finish.
C Exterior curtain wall from 6” x 16 ga. (54 mils) steel studs at 16” o.c. Finish exterior face of wall with acrylicelastomeric finish coat over fiberglass reinforcing mesh embedded in 1/16” — 3/32” thick acrylic polymermodified cementitious base coat over 2” thick expanded polystyrene insulation (EPS) adhered with abovebase coat to 3/8” thick factory mixed cementitious one-coat stucco with acrylic polymer admixture over 2.5lb. /sq. yd. self-furring diamond mesh metal lath over Tyvek CommercialWrap D over 5/8” exterior gradegypsum board sheathing. Back wrap all EPS shapes with fiberglass reinforcing mesh. Do not lap meshover one-coat stucco. Insulate wall with R-19 FSK-faced flame spread 25 fiberglass insulation. Fill holesat duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006IBC. Finish interior face of wall with 5/8” type “x” gypsum board to above ceiling height at time of tenantfinish. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsumboard below ceiling height with Level 5 finish.
D Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish common area side of wall with 5/8” type “x” gypsum board to undersideof floor or roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum boardbelow ceiling height with Level 5 finish. Finish tenant side of wall with 5/8” type “x” gypsum board tounderside of floor or roof deck at time of tenant finish.
E Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck abovewith slip joint at top of wall. Finish both faces of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Insulate wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board on Corridorside of wall below ceiling height with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side ofwall with Level 2 finish.
F Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish both faces of wall with 5/8”type “x” gypsum board to underside of beam, floor or roof deck above. Insulate wall with 3-1/2” soundattenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed to maintainthe fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes at duplexes,switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Providefireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board below ceilingheight with Level 5 finish. Finish gypsum board on Electrical Eqpt. Room side of wall with Level 2 finish.
G Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, diagonal brace or roof deck above with slip joint at top of wall. Finish face of wall with5/8” type “x” gypsum board to underside of floor or roof deck above. Insulate tenant side of wall with 3-1/2”sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installed tomaintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onStair side of wall below ceiling height with Level 5 finish. Finish gypsum board on Tenant side of wallbelow ceiling height with Level 5 finish. Finish gypsum board on Mech. Shaft side of wall with Level 1finish.
H Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” gypsum board to underside of flooror roof deck above. Fill holes at duplexes, switches and other voids with expanding foam sealant thatcomplies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717,2006 IBC. Finish gypsum board below ceiling height with Level 5 finish.
J Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam or diagonal braceabove with slip joint at top of wall. Finish face of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate Toilet Room side of wall with 3-1/2” sound attenuation battinsulation. Fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
K Interior wall from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of beam, floor or roof deckabove with slip joint at top of wall. Finish face of Toilet Room and Janitor Closet side of walls with 5/8” type“x” moisture resistant gypsum board to underside of beam, floor or roof deck above. Finish face of corridorside of walls with 5/8” type “x” gypsum board to underside of beam, floor or roof deck above. Insulate toiletroom side of wall with 3-1/2” sound attenuation batt insulation. Fill holes at duplexes, switches and othervoids with expanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking anddraftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board above tile wainscot and belowceiling height in Toilet Rooms with Level 5 finish. Finish gypsum board behind tile wainscot in Toilet Roomsand behind fiberglass reinforced plastic panels (FRP) in Janitor Closet with Level 2 finish. Refer to ToiletRoom Elevations on sheet A5.
L Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Janitor Closet sideof wall with 5/8” type “x” moisture resistant gypsum board to underside of beam, floor or roof deck above.Finish face of Stair side of wall with 5/8” type “x” gypsum board to underside of beam, floor or roof deckabove. Insulate wall with 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessedfixtures shall be installed to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Wherepermitted fill holes at duplexes, switches and other voids with expanding foam sealant that complies withSec. 2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board on Stair side of wall with Level 5 finish. Finish gypsum board on Janitor side of wallbehind fiberglass reinforced plastic panels with Level 2 finish.
M Interior wall from 6” x 25 ga. (18 mils) steel studs at 16” o.c. to underside of floor or roof deck above withslip joint at top of wall. Finish both faces of wall with 5/8” type “x” moisture resistant gypsum board tounderside of floor or roof deck above. Insulate wall with 2 layers 3-1/2” sound attenuation batt insulation.Fill holes at duplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603,2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finishgypsum board above tile wainscot and below ceiling height with Level 5 finish. Finish gypsum boardbehind tile wainscot with Level 2 finish. Refer to Toilet Room Elevations on sheet A5.
N Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam above with slip joint at top of wall. Finish face of Elevator side of wall with 1” gypsumboard liner panels to underside of beam above. Finish face of Corridor, Communications and ElevatorEqpt. Room side of wall with 5/8” type “x” gypsum board to underside of beams above. Finish face of Stairside of wall with 5/8” type “x” gypsum board. Insulate wall with 3-1/2” sound attenuation batt insulation.Through wall penetrations and recessed fixtures shall be installed to maintain the fire resistive rating of thewall per Section 712, 2006 IBC. Where permitted fill holes at duplexes, switches and other voids withexpanding foam sealant that complies with Sec. 2603, 2006 IBC. Provide fireblocking and draftstoppingwhere required per Sec. 717, 2006 IBC. Finish gypsum board on Corridor and Stair side of wall with Level5 finish. Finish gypsum board on Communications and Elevator Eqpt. Room side of wall with Level 2finish.
P Interior wall of 1-hour fire resistive construction from 4” x 25 ga. (18 mils) steel CH or CT studs at 24” o.c.to underside of beam or roof deck above with slip joint at top of wall. Finish face of Mech. Shaft side ofwall with 1” gypsum board liner panels to underside of beam or roof deck above. Finish face of Tenantside of wall with 5/8” type “x” gypsum board to underside of beam or roof deck above. Insulate wall with3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall be installedto maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fill holes atduplexes, switches and other voids with expanding foam sealant that complies with Sec. 2603, 2006 IBC.Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC. Finish gypsum board onTenant side of wall with Level 5 finish.
R Interior wall of 1-hour fire resistive construction from 3-5/8” x 25 ga. (18 mils) steel studs at 16” o.c. tounderside of beam, floor or roof deck above with slip joint at top of wall. Finish face of Stair side ofwall with 5/8” type “x” gypsum board to underside of roof deck above. Finish face of Tenant side ofwall with 2 layers 5/8” type “x” gypsum board to underside of floor or roof beam above. Insulate wallwith 3-1/2” sound attenuation batt insulation. Through wall penetrations and recessed fixtures shall beinstalled to maintain the fire resistive rating of the wall per Section 712, 2006 IBC. Where permitted fillholes at duplexes, switches and other voids with expanding foam sealant that complies with Sec.2603, 2006 IBC. Provide fireblocking and draftstopping where required per Sec. 717, 2006 IBC.Finish gypsum board below ceiling height with Level 5 finish.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A3
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
1
2
3
4
5
6
7
8
9
A B C D E F G H J K
1A9
2A9
3A10
4A10
2A11
2A11
1'-75/16" 34'-67/8" 69'-4" 34'-613/16" 1'-75/16"
65
/8
"2
'-1
03
/1
6"
1'-
75
/1
6"
16
'-6
9/
16
"
65
/8
"4
4'-
31
/4
"
65
/8
"1
6'-
69
/1
6"
1'-
75
/1
6"
2'-
10
1/
4"
65
/8
"
35
/8
"4
'-4
"1
8'-
53
/8
"1
1'-
83
/8
"9
'-5
5/
8"
9'-
55
/8
"1
1'-
83
/8
"1
8'-
53
/8
"4
'-4
"3
5/
8"
1'-213/16" 35'-6" 3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7" 39'-0" 1'-213/16"
1'-75/16"37'-97/8"
65/8"61'-83/4"
65/8"37'-913/16"
1'-75/16"
141'-85/16"
65
/8
"2
'-1
03
/1
6"
1'-
75
/1
6"
16
'-6
9/
16
"
65
/8
"4
4'-
31
/4
"
65
/8
"1
6'-
69
/1
6"
1'-
75
/1
6"
2'-
10
1/
4"
65
/8
"
3'-
41
3/
16
"8
1'-
85
/1
6"
3'-
47
/8
"
88
'-6
"
3'-
41
3/
16
"8
1'-
85
/1
6"
3'-
47
/8
"
88
'-6
"
1'-75/16"37'-97/8"
65/8"61'-83/4"
65/8"37'-913/16"
1'-75/16"
141'-85/16"
3'-105/8"
3'-105/8"
3'-
10
5/
8"
3'-
10
5/
8"
3'-105/8"
3'-105/8"
3'-
10
5/
8"
3'-
10
5/
8"
RoofHatch
Cricket Slopeat 1/4" Per Ft.
Cricket Slopeat 1/4" Per Ft.
Cricket Slopeat 1/4" Per Ft.
Cricket Slopeat 1/4" Per Ft.
Building Line Below
Scale: 1/8" = 1'-0"
Roof Plan1
/4
" P
er F
t.
1/
4" P
er F
t.
1/
4" P
er F
t.
1/
4" P
er F
t.
1/2
" Pe
r F
t.
1/2
" Pe
r Ft.
1/2
" Pe
r Ft.
1/2
" Pe
r F
t.
1/2
" Pe
r Ft.
1/2
" Pe
r F
t.
1/2
" Pe
r F
t.
1/2
" Pe
r Ft.
Rid
ge
Rid
ge
RidgeRidge
1A11
1A11
EF-1See Mech.
RTU-1See Mech.
RH-1See Mech.
Roof Drain
Relief Drain
Roof Drain
Relief Drain
Roof Drain
Relief Drain
Roof Drain
Relief Drain
1
5"
1'-
4"
11
/2
"
31
/2
"
2 3
/8
" A
t H
igh P
t.
8" M
in.
5"
Nystrom Building ProductsRHGS Roof Hatch - 48"x144"
Min. R-30 Flat and TaperedPolyiso. Foam Insul. Board
1.5 B22 MetalRoof Deck
Spray-AppliedFireproofing
60 Mil TPO Membrane
w12x14 Steel Beam
5/8" Type "X" Gyp. Bd.
(2) P.T. 2x4
P.T. 2x4 -Rip to 3" Wide
Not To Scale
Roof Hatch Section
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A4
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary1
10
0A
10
0A
18
0A
18
0A
14
0B
14
0B
15
0B
15
0B
4
5
6
B C D E F G H J
10
7A
10
7A
10
6A
10
6A
10
5A
10
5A
10
8A
10
8A
11
0A
11
0A
11
2A
11
2A U
P 1
2 R
. @ 7
" 1
1 T
. @ 1
1"
UP
12
R. @
7"
11
T. @
11
"
UP
12
R. @
7"
11
T. @
11
"
UP
12
R. @
7"
11
T. @
11
"
9'-
55
/8
"9
'-5
5/
8"
3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7"
35/8"6'-11/4"
4"6'-11/4"
4"
35
/8
"4
'-5
1/
2"
4"
8'-
61
/8
"
4"
4'-
51
/2
" 35
/8
"
35
/8
"4
'-6
11
/1
6"
10
1/
8"
8'-
99
/1
6"
6"
8'-
99
/1
6"
10
1/
8"
4'-
61
1/
16
"
35
/8
"
101/8"8'-41/16"
35/8"4'-11/4"
35/8"2'-83/8"
35/8"5'-11/4"
35/8"4'-111/4"
35/8"8'-11/8"
35/8"5'-71/4"
35/8"3'-23/8"
35/8"3'-2"
35/8"8'-4"
101/8"
35
/8
"5
'-1
3/
16
" 35
/8
"3
'-8
3/
8"
35
/8
"9
'-4
"3
5/
8"
4'-
51
/2
"
35
/8
"5
'-1
3/
16
" 35
/8
"
101/8"8'-41/16"
35/8"5'-71/4"
35/8"
1'-23/8"
35/8"5'-11/4"
35/8"13'-4"
35/8"5'-71/4"
35/8"3'-23/8"
35/8"11'-95/8"
101/8"
35
/8
"4
'-4
15
/1
6"
81
/4
"3
5/
8"
18
'-1
1/
8"
35
/8
"8
1/
4"
4'-
41
5/
16
"
35
/8
"
35
/8
"4
'-4
15
/1
6"
81
/4
"3
5/
8"
18
'-1
1/
8"
35
/8
"8
1/
4"
4'-
41
5/
16
"
35
/8
"
57'-1113/16"
29
'-6
"
29
'-6
"
57'-1113/16"
3'-
11
"
2'-23/4"
4'-
35
/8
"5
'-7
"
2'-23/4"
2'-
1"
1'-
11
"
35
/8
"3
'-0
"1
'-0
"1
0'-
1"
1'-
11
"2
'-1
1/
8"
35
/8
" 1A12
1A12
2A12
5A5
5A5
A
B
C
D3
A5
A
B
C
D4
A5
Scale: 1/4" = 1'-0"
First Floor Core Plan
North
Opp
Hand
Stair105
Janitor107
Elec.106
Corridor104
Corridor102
Co
rrid
or
10
3
Co
rrid
or
10
1
Women's108
Men's109
Elevator111
Comm.110
Stair112
Me
ch.
Sha
ftA
bo
ve
Me
ch.
Sha
ftA
bo
ve
G
G
H
M
H
LK
KK
K
J
J
DD
D D
F
R
R
F
F
E
FE
N
N
G
G
K
K
10
9A
10
9A
35/8"7'-11/4"
35/8"
1'-
11
"2
'-1
"
35
/8
"2
'-1
1/
8"
1'-
11
"1
0'-
1"
1'-
0"
3'-
0"
35
/8
"
4'-1/4"
31/2"4'-1/4"
4'-0"41/16"
4'-0"
2'-
2"
3'-
10
15
/1
6"
1"
5'-
11
/4
"5
'-1
1/
4"
1"
3'-
10
15
/1
6"5'-1"
1"1'-6" 1'-6"
1"101/4" 4'-23/4"
5'-1"1"
2'-111/16"105/16"
1"
2'-13/4"
2'-111/4"
1" 3'-0" 1" 5'-1"
1"3'-0"
1"5'-1"
4'-
0"
9" M
in.
27
" M
in.
TowelDispenser
Elevation "D"
Exposed pipes underLavatories and sinksshall be insulated orconfigured to preventcontact
Sink shall be 6 1/2"deep max.
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Toilet room walls shallbe finished withceramic tile to 48" min.above finish floor over5/8" M.R. gyp. bd.
12
" M
in.
24" Min. 12" Min.36" Min.
Elevation "C"
27
" M
in.
17
" - 1
9"
Exposed pipes underLavatories and sinksshall be insulated orconfigured to preventcontact
Sink shall be 6 1/2"deep max.
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Indicates Backing inWall
Mirror - 40" Max A.F.F.to bottom edge ofglass
33
" - 3
6"
48
" M
in.
12
" M
in.
5/8" M.R. gyp. bd. (pnt.)
Elevation "B"
Toe Clearance
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Toilet room walls shallbe finished with tile to48" min. above finishfloor over 5/8" M.R.gyp. bd.
3
5/8" M.R. gyp. bd. (pnt.)
Elevation "A"
Scale: 3/8" = 1'-0"
Women's Toilet Room Elevations
The toilet room floorshall be tile with a 6"high tile sanitary covebase
12
" M
in.
5/8" M.R. gyp. bd. (pnt.)
Elevation "B"
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Toilet room walls shallbe finished with tile to48" min. above finishfloor over 5/8" M.R.gyp. bd.
5/8" M.R. gyp. bd. (pnt.)
Elevation "C"
The toilet room floorshall be tile with a 6"high tile sanitary covebase
8" Min
11" Min
Towel Dispenser
Elevation "D"
Exposed pipes underlavatories and sinksshall be insulated orconfigured to preventcontact
Sink shall be 6 1/2"deep max.
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Toilet room walls shallbe finished with tile to48" min. above finishfloor over 5/8" M.R.gyp. bd.
SCALE: 3/8'' = 1' - 0''5
Toilet Stall Elevation
39"-41"
42" Min.
17
"-1
9"
15
" M
in.
7"-9"
12
" M
in.
33
" - 3
6"
39
" - 4
1"
18
" M
in.
4
17
"-1
9"
17
" M
ax
12" Min. 24" Min.
36" Min.
Elevation "A"
Scale: 3/8" = 1'-0"
Men's Toilet Room Elevations
Exposed pipes underlavatories and sinksshall be insulated orconfigured to preventcontact
Sink shall be 6 1/2"deep max.
The toilet room floorshall be tile with a 6"high tile sanitary covebase
Toilet room walls shallbe finished with tile to48" min. above finishfloor over 5/8" M.R.gyp. Bd.
Indicates Backingin Wall
Mirror - 40" Max A.F.F.to bottom edge ofglass
Toilet Room AccessoriesSoap Dispensers 4 required per floor (2 each in Men's and Women's)
AS 0332 Lavatory Mounted Soap Dispenser
Towel Dispensers 2 required per floor (1 each in Men's and Women's)
AS 0469 Paper Towel Dispenser and Waste Receptacle
Napkin Vendor 1 required per floor (1 each in Women's)
AS 0464-50 Recessed Dual Sanitary Napkin/Tampon Vendor
Napkin Disposals 1 required per floor (1 each in Women's)
AS 0472-1 Partition Mounted Dual Access Sanitary Napkin Disposal
Toilet Paper Holders 3 required per floor (1 each in Men's and 2 each in Women's)
AS 0030 Surface Mounted Daul Roll Toilet Paper Dispenser
Grab Bars 2 required per floor (1 each in Men's and Women's)
AS 3201-36 Grab Bar with Concealed Mounting Flange
2 required per floor (1 each in Men's and Women's)
AS 3201-42 Grab Bar with Concealed Mounting Flange
2 required per floor (1 each in Men's and Women's)
AS 3201-18 Grab Bar with Concealed Mounting Flange
Changing Stations 2 required per floor (1 each in Men's and Women's)
AS 9012 Horizontal Baby-Changing Station
Mirrors 2 required per floor (1 each in Men's and Women's)
AS 0600-A 60"W. x 48"H. Angle Frame Mirror
Toilet Partitions
Notes:1.
2.
3.
All accessory model numbers are American Specialties, Inc. except the toilet partitions.
Submit 3 copies of submittals and shop drawings, including details and color samples toArchitect for approval.
Provide necessary backing where required for all accessories and use stainless steelvandal-resistant fasteners at all accessories with exposed fasteners.
1 compartment and 1 urinal screen with 56" high pilaster required perfloor in Men's, and 2 compartments required per floor in Women's MillsBaked Enamel Series 400 - Sentinel Floor-Mounted Overhead BracedRestroom Partitions, color to be selected by Architect fromstandard colors
Toilet Room Notes
1. Faucets for accessible lavatoriesshall comply with section 309,ICC/ANSI A117.1. Hand operated,self-closing faucets shall remainopen for 10 seconds minimum. Theshape of the faucet handles forthe accessible lavatories shall beoperable with one hand and notrequire tight grasping, pinching ortwisting of the wrist, and the forcerequired to activate the handlesshall not be more than 5 pounds.
2. Exposed pipes under lavatoriesand sinks shall be insulated orconfigured to prevent contact.
3. Flush controls for all toilets andurinals will be at 48" max. abovefinished floor.
4. Toilet room walls shall be finishedwith tile to 48" min. above finishedfloor over 5/8" moistureresistant gypsum board.
5. The toilet room floor shall be tilewith a 6" high tile sanitary covebase.
6. Indicates backing for toiletaccessories.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A5
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
DO
WN
12
R. @
7"
11
T. @
11
"
DO
WN
12
R. @
7"
11
T. @
11
"
1
4
5
6
B C D E F G H J
20
7A
20
7A
20
6A
20
6A
20
5A
20
5A
20
9A
20
9A
20
8A
20
8A
21
0A
21
0A
21
2A
21
2A
20
0B
20
0B
20
0A
20
0A
UP
12
R. @
7"
11
T. @
11
"
UP
12
R. @
7"
11
T. @
11
"
UP
12
R. @
7"
11
T. @
11
"
UP
12
R. @
7"
11
T. @
11
"
1A12
1A12
2A12
5A5
5A5
A
B
C
D3
A5
A
B
C
D4
A5
3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7"
9'-
55
/8
"9
'-5
5/
8"
35/8"
6'-11/4"
4"
6'-11/4"
4"
35
/8
"
4'-
51
/2
"
4"
8'-
61
/8
"
4"
4'-
51
/2
"
35
/8
"
35
/8
"
4'-
61
1/
16
"
10
1/
8"
8'-
99
/1
6"
6"
8'-
99
/1
6"
10
1/
8"
4'-
61
1/
16
"
35
/8
"
4"2'-23/4"
61/2" 35/8"
8'-41/16"
35/8"
5'-71/4"
35/8"
1'-23/8"
35/8"
5'-11/4"
35/8"
13'-4"35/8"
8'-2"
35/8"
4'-11/4"
35/8"
8'-4"
101/8"
2'-23/4"
4"
35
/8
"
5'-
13
/1
6" 3
5/
8"
3'-
83
/8
"
35
/8
"
10
'-1
1/
8"
35
/8
"
3'-
83
/8
"
35
/8
"
5'-
13
/1
6" 3
5/
8"
4"
2'-23/4"
101/8"
8'-41/16"
35/8"
5'-71/4"
35/8"
1'-23/8"
35/8"
5'-11/4"
35/8"
13'-4"
35/8"
8'-2"
35/8"
4'-11/4"
35/8"
8'-4"
35/8" 61/2"
2'-23/4"
4"
35
/8
"
4'-
41
5/
16
"
81
/4
"3
5/
8"
3'-
8" 4
"
5'-
7"
4"
8'-
21
/8
"
35
/8
"8
1/
4"
4'-
41
5/
16
"
35
/8
"
35
/8
"
4'-
41
5/
16
"
81
/4
"3
5/
8"
13
'-1
01
/8
"
4"
3'-
11
" 4"
77
/8
"
4'-
41
5/
16
"
35
/8
"
63'-15/16"
29
'-6
"
29
'-6
"
63'-15/16"
3'-
1/
8"
1'-
0"
1'-
11
"2
'-1
"
35
/8
"5
'-1
3/
16
" 35
/8
"2
'-1
1/
8" 1
'-1
1"
10
'-1
"1
'-0
"3
'-0
"3
5/
8"
81
/4
"
35
/8
"3
'-0
"1
'-0
"1
0'-
1"
1'-
11
"2'-
11
/8
"3
5/
8"
2'-
1"
1'-
11
"1
0'-
1"
1'-
0"
3'-
1/
8"
Scale: 1/4" = 1'-0"
Second Floor Core Plan
North
Opp
Hand
RefugeArea
Stair205
Janitor207
Elec.206
Corridor204
Corridor202
Co
rrid
or
20
3
Co
rrid
or
20
1
Women's208
Men's209
RefugeArea
Elevator211
Comm.210
Stair212
Me
ch.
Sha
ft
Me
ch.
Sha
ft
G
G
H
M
H
LK
KK
K
J
J
DD
D D
F
R
R
F
F
E
F
N
N
G
G
K
K
E
P
P
P
P
P
P
4'-1/4"
31/2"4'-1/4"
4'-0"41/16"
4'-0"
2'-
2"
3'-
10
15
/1
6"
1"
5'-
11
/4
"5
'-1
1/
4"
1"
3'-
10
15
/1
6"5'-1"
1"1'-6" 1'-6"
1"101/4" 4'-23/4"
5'-1"1"
2'-111/16"105/16"
1"
2'-13/4"
2'-111/4"
1" 3'-0" 1" 5'-1"
1"3'-0"
1"5'-1"
DO
WN
12
R. @
7"
11
T. @
11
"
DO
WN
12
R. @
7"
11
T. @
11
"
DO
WN
12
R. @
7"
11
T. @
11
"
2
4
5
6
B C D E F G H J
30
7A
30
7A
30
6A
30
6A
30
5A
30
5A
31
0A
31
0A
31
2A
31
2A
30
0B
30
0B
30
0A
30
0A
UP
12 R
. @
7"
11 T
. @
11"
1A12
1A12
2A12
5A5
5A5
A
B
C
D3
A5
A
B
C
D4
A5
3'-6" 18'-75/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 7'-7"
9'-
55
/8
"9
'-5
5/
8"
35/8"6'-11/4"
4"6'-11/4"
4"
35
/8
"
4'-
51
/2
"
4"
8'-
61
/8
"
4"
4'-
51
/2
" 35
/8
"
35
/8
"
4'-
61
1/
16
"
10
1/
8"
8'-
99
/1
6"
6"
8'-
99
/1
6"
10
1/
8"
4'-
61
1/
16
"
35
/8
"
4"2'-23/4"
61/2" 35/8"
8'-41/16"
35/8"
5'-71/4"
35/8"
1'-23/8"
35/8"
5'-11/4"
35/8"
13'-4"35/8"
8'-2"35/8"
4'-11/4"
35/8"
8'-4"101/8"
2'-23/4"
4"
35
/8
"
5'-
13
/1
6" 3
5/
8"
3'-
83
/8
"
35
/8
"
10
'-1
1/
8"
35
/8
"
3'-
83
/8
"
35
/8
"
5'-
13
/1
6" 3
5/
8"
4"
2'-23/4"
101/8"
8'-41/16"
35/8"
5'-71/4"
35/8"
1'-23/8"
35/8"
5'-11/4"
35/8"
13'-4"
35/8"
8'-2"
35/8"
4'-11/4"
35/8"
8'-4"
35/8" 61/2"
2'-23/4"
4"
35
/8
"
4'-
41
5/
16
"
77
/8
"4
"
9'-
7"
4"
8'-
21
/8
"
35
/8
"8
1/
4"
4'-
41
5/
16
"
35
/8
"
35
/8
"
4'-
41
5/
16
"
81
/4
"3
5/
8"
10
'-6
1/
8"
4"
7'-
3"
4"
77
/8
"
4'-
41
5/
16
"
35
/8
"
63'-15/16"
29
'-6
"
29
'-6
"
63'-15/16"
3'-
1/
8"
1'-
0"
1'-
11
"2
'-1
"
35
/8
"5
'-1
3/
16
" 35
/8
"2
'-1
1/
8" 1
'-1
1"
10
'-1
"1
'-0
"3
'-0
"3
5/
8"
81
/4
"
81
/4
"
35
/8
"3
'-0
"1
'-0
"
2'-
1"
1'-
11
"1
0'-
1"
1'-
0"
3'-
1/
8"
35
/8
"
Scale: 1/4" = 1'-0"
Third Floor Core Plan
North
Opp
Hand
RefugeArea
Stair305
Janitor307
Elec.306
Corridor304
Corridor302
Co
rrid
or
30
3
Co
rrid
or
30
1
Women's308
Men's309
RefugeArea
Elevator311
Elev.Eqpt.310
Stair312
UP
13
R. @
7"
12
T. @
11
" Me
ch.
Sha
ft
Me
ch.
Sha
ft
G
G
H
M
H
LK
KK
K
J
J
DD
D D
F
F
F
F
F
E
F
N
N
G
G
K
K
E
P
P
P
P
P
P
30
9A
30
9A
30
8A
30
8A
51/8"
3'-3"1'-37/8"
3'-4"
4'-0"41/16"
4'-0"
2'-
2"
3'-
10
15
/1
6"
1"
5'-
11
/4
"5
'-1
1/
4"
1"
3'-
10
15
/1
6"5'-1"
1"1'-6" 1'-6"
1"101/4" 4'-23/4"
5'-1"1"
2'-111/16"105/16"
1"
2'-13/4"
2'-111/4"
1" 3'-0" 1" 5'-1"
1"3'-0"
1"5'-1"
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A6
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary1
67
/1
6"
Eq
1'-
91
1/
16
"1
'-1
"1
'-0
15
/1
6"
1'-
91
1/
16
"
61/2" Eq
61/2" Eq
Eq
Eq
61/8" 61/2"61/2" 1'-111/2"
61/2" 1'-65/8" 61/8" 61/2"
61
/2
"E
q
Eq
Eq Eq
Eq
Eq Eq
1'-
10
3/
4"
1'-
10
3/
4"
Eq
67
/1
6"
Eq
61
/2
"
Eq 61/2"
Eq 61/2"
1'-
10
3/
4"
61
/2
"E
qE
q6
7/
16
"
ExposedStructure- Paint
For Continuation SeeFoyer & Lobby ReflectedCeiling Plan Below
For Continuation See FirstFloor Corridor ReflectedCeiling Plan Below
Scale: 1/4" = 1'-0"
First Floor CoreReflected Ceiling Plan
North
ExposedStructure
-Paint
Paint Undersideof Stairs and
LandingsExposed
Structure-Paint
Indirect Light Cove
Indirect Light Cove
Paint Undersideof Stairs and
Landings
Stair105
Janitor107
Elec.106
Corridor104
Corridor102
Co
rrid
or
10
3
Co
rrid
or
10
1
Women's108
Men's109
Elevator111
Comm.110
Stair112
2
67
/1
6"
Eq
61
/2
"E
q
1'-
10
3/
4"
1'-
10
3/
4"
1'-
91
1/
16
"1
'-1
"1
'-1
"1
'-9
11
/1
6"
61/2" Eq
61/2" Eq
73/8" 61/2"61/2" 1'-111/2"
1'-67/8" 61/2"61/2" 69/16"
Eq Eq
Eq
Eq
Eq
Eq
Eq Eq
Eq 61/2"
Eq 61/2"
Eq
61
/2
"
Eq
67
/1
6"
61
/2
"E
qE
q6
7/
16
"
ExposedStructure - Paint
Scale: 1/4" = 1'-0"
Second Floor CoreReflected Ceiling Plan
North
ExposedStructure
-Paint
ExposedStructure
-Paint
Indirect Light Cove
Indirect Light Cove
RefugeArea
Stair205
Janitor207
Elec.206
Corridor204
Corridor202
Co
rrid
or
20
3
Co
rrid
or
20
1
Women's208
Men's209
RefugeArea
Elevator211
Comm.210
Stair212
Paint Undersideof Stairs and
Landings
Paint Undersideof Stairs and
Landings
Me
ch.
Sha
ft
Me
ch.
Sha
ft
3
67
/1
6"
Eq
61
/2
"E
q
61/2" Eq
61/2" Eq
1'-
1"
1'-
91
1/
16
"
61/2" 73/16" 1'-67/8" 61/2"
Eq
61
/2
"
Eq 61/2"
73/8" 61/2"61/2" 1'-111/2"
Eq 61/2"
1'-
91
1/
16
"1
'-1
"
Eq
67
/1
6"
Eq Eq
Eq
Eq
Eq
Eq
Eq Eq
1'-
10
3/
4"
1'-
10
3/
4"
61
/2
"E
qE
q6
7/
16
"
ExposedStructurew/SFP -Paint
Scale: 1/4" = 1'-0"
Third Floor CoreReflected Ceiling Plan
North
ExposedStructure
w/SFP-Paint
ExposedStructure
w/SFP-Paint
ExposedStructure
w/SFP-Paint
ExposedStructurew/SFP -No Paint
Exp.Struc.w/SFP
Indirect Light Cove
Indirect Light Cove
ExposedStructure
w/SFP-Paint
Exp.Struc.w/SFP
RefugeArea
Stair305
Janitor307
Elec.306
Corridor304
Corridor302
Co
rrid
or
30
3
Co
rrid
or
30
1
Women's308
Men's309
RefugeArea
Elevator311
Elev.Eqpt.310
Stair312
Me
ch.
Sha
ft
Me
ch.
Sha
ft
41
'-0
"E
q6
'-0
"6
'-0
"E
q 1'-
0"
8"E
qE
q1
'-4
"
1'-0" Eq 6'-0" Eq 1'-0"
1'-0"1'-0"
IndirectLight Cove
Scale: 1/4" = 1'-0"
Foyer & LobbyReflected Ceiling Plan
Soffit
Soffit
FlatCoffer
CurvedCoffer
Hip
Hip
Hip Hip
PendantFixture
PendantFixture
Lobby113
Foyer114
5
10
1/
2"
1'-
11
"
61/2" Eq
1'-
10
3/
4"
Eq 61/2"
Scale: 1/4" = 1'-0"
First Floor CorridorReflected Ceiling Plan
Co
rrid
or
11
6
FireSprinkler
117
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A7
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary2
12'-8"
2"3'-0"
2"6'-0"
2"3'-0"
2"
2"
2'-
9"
2"
3'-
11
"2
"1
'-8
"2
"
9'-
0"
7'-
0"
2"
1'-
8"
2"
9'-
0"
3
2"
2'-
9"
2"
3'-
11
"2
"1
'-8
"2
"
9'-
0"
7'-
0"
2"
1'-
8"
2"
9'-
0"
2"2'-111/4"
2"2'-113/8"
2"2'-113/8"
2"3'-0"
2"
12'-8"
1
2"3'-0"
2"
3'-4"
7'-
0"
2"
7'-
2"
Scale: 1/4" = 1'-0"
Frame Types
B
3'-0" 3'-0"
6'-0"
10
"5
'-1
01
/2
"
31
/2
"
31/2" 31/2"31/2" 31/2"
7'-
0"
C
3'-0"
10
"5
'-1
01
/2
"
31
/2
"
31/2"31/2"
A
7'-
0"
3'-0"
Door TypesScale: 1/4" = 1'-0"
1
2"4'-0"
2"4'-0"
2"4'-0"
2"
2"
3'-
10
"2
"
1'-
8"
2"
1'-11"2"
1'-11"2"
6'-
0"
12'-8"
Window TypesScale: 1/4" = 1'-0"
2
2"4'-0"
2"4'-0"
2"4'-0"
2"4'-0"
2"
1'-11"2"
1'-11"
2"
3'-
10
"2
"1
'-8
"2
"
6'-
0"
16'-10"
Door ScheduleMark Size Door Frame Spec. Hdwe.
Width Height Thick. Type Mat'l. Fin. Type Mat'l. Fin.
First Floor
100A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
105A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
106A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
107A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
108A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
109A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
110A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
112A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
113A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW5
114A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW6
116A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
120A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
130A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
140A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
140B 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
150A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
150B 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
160A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
170A (2)3'-0" 7'-0" 1-3/4" B Alum. Prefin. 2 Alum. Prefin. DF2 HW4
180A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
Second Floor
200A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
200B 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
205A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
206A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
207A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
208A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
209A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
210A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
212A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
Third Floor
300A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
300B 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW1
305A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
306A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
307A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
308A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
309A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW4
310A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW3
312A 3'-0" 7'-0" 1-3/4" A SCWD Stn. 1 HM Pnt. DF1 HW2
Door and Frame Specifications (Spec.):
DF1
DF2
Finish Schedule
Rm. Name Floor Base Walls Ceiling Spec.
Mat'l. Fin. Mat'l. Fin. Hgt.
First Floor
100 Tenant Conc. none none none none none na G1,F1
101 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
102 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
103 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
104 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
105 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
106 Electrical Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
107 Janitor Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,W5,C5
108 Women's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
109 Men's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
110 Comm. Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
111 Elevator na na Gyp.Bd. none na na na na
112 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
113 Lobby Tile Tile Gyp.Bd. Pnt. Gyp.Bd. Pnt. F5,B1,W1,W3,C2
114 Foyer Tile Tile Gyp.Bd. Pnt. Gyp.Bd. Pnt. F5,B1,W1,W3,C1
115 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W4,C1,C3
116 Sprinkler Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
120 Tenant Conc. none none none none none na G1,F1
130 Tenant Conc. none none none none none na G1,F1
140 Tenant Conc. none none none none none na G1,F1
150 Tenant Conc. none none none none none na G1,F1
160 Tenant Conc. none none none none none na G1,F1
170 Tenant Conc. none none none none none na G1,F1
180 Tenant Conc. none none none none none na G1,F1
Second Floor
200 Tenant Conc. none none none none none na G1,F1
201 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
202 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
203 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
204 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
205 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
206 Electrical Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
207 Janitor Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,W5,C5
208 Women's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
209 Men's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
210 Comm. Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
211 Elevator na na Gyp.Bd. none na na na na
212 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
Third Floor
300 Tenant Conc. none none none none none na G1,F1
301 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
302 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
303 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
304 Corridor Carpet Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 9'/10' F3,B1,W1,W3,C1,C3
305 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc./SFP Pnt. na F2,B2,W2,C6
306 Electrical Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
307 Janitor Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,W5,C5
308 Women's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
309 Men's Tile Tile Gyp.Bd. Pnt. Gyp.Bd./SAT Pnt. 8'/9' F4,B3,W1,W4,C2,C4
310 Elev. Eqpt. Conc. Rubber Gyp.Bd. Pnt. Exp.Struc. Pnt. na F2,B2,W2,C5
311 Elevator na na Gyp.Bd. none Exp.Struc./SFP Pnt. na na
312 Stair Conc. Rubber Gyp.Bd. Pnt. Exp.Struc./SFP Pnt. na F2,B2,W2,C6
Finish Specifications (Spec.):
General
G1 Unfinished tenant space
Floors
F1 Unfinished concrete slab
F2 Concrete slab sealed with 2-cts. PROSOCO SpecSeal WB-Flat. Prepare surface
and apply per manufacturer's recommendations.
F3 Carpet
F4 Tile
F5 Tile
Bases
B1 Tile
B2 Rubber cove base
B3 Tile
Walls
W1 Gypsum board
W2 Gypsum board
W3 Wainscot
W4 Wainscot
W5 FRP
CeilingsC1 Gypsum board soffit
C2 Gypsum board light cove
C3 SAT
C4 SAT
C5 Exposed structure
C6 Exposed structure with spray fireproofing
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A8
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary1
14
'-0
"1
4'-
0"
14
'-0
"2
'-4
"2
'-6
"
2'-
0"
8"
4"
6'-
8"
4"
3'-
4"
4"
1'-
4"
1'-
0" 1'-
0"
6'-
0"
1'-
0"
6'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"
1'-
4"
1'-
0"
2"
1'-
4"
1'-
0"
R-1
2'-
8"
Tan Storefront Window Framingw/ 1" Insul. Glazing
Stucco Finish
EPS Crown Mouldingw/ Stucco Finish
4" Brick VeneerEntry Pilasters& Arch
2" EPS Pilaster w/Stucco Finish
Med. Stile Alum. Doorw/ 1/4" Temp. Glazing
Alum. Storefront WindowFraming w/ 1" Insul. Glazing
MetalCoping
EPS Capitalw/ StuccoFinish
4" BrickVeneerPilaster
Parapet
Roof
3rd Floor
2nd Floor
1st Floor
Parapet
Scale: 1/8" = 1'-0"
West Elevation
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
2
2'-
0"
8"
4"
6'-
0" 8
"4
"3
'-4
"4
"
2'-
71
/2
"
81
/2
"6
'-0
"1
'-0
"4
'-0
"2'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"
1'-
4"
1'-
0"
2"
1'-
4"
1'-
0"
14
'-0
"1
4'-
0"
14
'-0
"2
'-4
"2
'-6
"
R-1
2'-
8"
Stucco Finish
EPS Crown Mouldingw/ Stucco Finish
Med. Stile Alum. Doorw/ 1/4" Temp. Glazing
4" Brick VeneerEntry Pilasters &Arch
Alum. Storefront WindowFraming w/ 1" Insul. Glazing
Alum. Storefront WindowFraming w/ 1" Insul. Glazing
Metal Coping
MetalCoping
EPS Capitalw/ StuccoFinish
4" BrickVeneerPilaster
2" EPS Pilaster w/Stucco Finish
Parapet
Roof
3rd Floor
2nd Floor
1st Floor
Parapet
Scale: 1/8" = 1'-0"
East Elevation
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A9
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
4
2'-
0"
8"
4"
6'-
0" 8
"4
"3
'-4
"4
"1'-
4"
1'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"
2'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"1
'-4
"1
'-0
"
2"
1'-
4"
1'-
0"
14
'-0
"1
4'-
0"
14
'-0
"2
'-4
"2
'-6
"
Tan Storefront Window Framingw/ 1" Insul. Glazing
Stucco FinishEPS Crown Mouldingw/ Stucco Finish
4" Brick VeneerEntry Pilasters& Arch
2" EPS Pilaster w/Stucco Finish
MetalCoping
EPS Capitalw/ StuccoFinish
4" BrickVeneerPilaster
Parapet
Roof
3rd Floor
2nd Floor
1st Floor
Parapet
Scale: 1/8" = 1'-0"
North Elevation
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
3
2'-
0"
8"
4"6
'-0
" 8"
4"
3'-
4"
4"
1'-
4" 1'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"
2'-
0"
1'-
0"
6'-
0"
1'-
0"
4'-
0"1
'-4
"1
'-0
"
2"
1'-
4"
1'-
0"
14
'-0
"1
4'-
0"
14
'-0
"2
'-4
"2
'-6
"
Tan Storefront Window Framingw/ 1" Insul. Glazing
Stucco FinishEPS Crown Mouldingw/ Stucco Finish
4" Brick VeneerEntry Pilasters& Arch
2" EPS Pilaster w/Stucco Finish
MetalCoping
EPS Capitalw/ StuccoFinish
4" BrickVeneerPilaster
Parapet
Roof
3rd Floor
2nd Floor
1st Floor
Parapet
Scale: 1/8" = 1'-0"
South Elevation
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
C.J.
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A10
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inaryA B C D E F G H J K
1
38'-1/16" 5'-715/16" 13'-115/8" 3'-73/4" 9'-2" 7'-6" 14'-83/8" 3'-5" 43'-2"
El = 100'-0"
El = 100'-0"
El - 128'-0"
El = Varies
146'-10"
5" Unreinf. Conc.Slab on Grade
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF on metaldeck re: Strl. (Typ.)
6" x 16 ga. Steel Studs at 16"O.C.
Acrylic Elastomeric Finish Coatover Acrylic Primer over 3/8"thick factory mixed cementitiousone coat stucco w/ acrylicpolymer admixture over 2.5 lb/sq.yd. self-furring diamond meshmetal lath over Tyvek CommercialWrap
5/8" Exterior Grade Gyp. Bd.Sheathing
R-19 FSK-Faced (Flame Spread25) Fiberglass Insulation
5/8" Gyp. Bd.(Level 5 FinishBelow Ceiling)
Refer to Window Schedule andWindow Types
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
Foundation per Strl.
Steel Frame per Strl.
Rigid Foam Cornice Profile
60 mil Fully AdheredEPDM Roof Membranew/ 16 mil Acrylic Coating
5" Unreinf. Conc.Slab on Grade
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF on metaldeck re: Strl. (Typ.)
Scale: 1/8" = 1'-0"
Building Section
First Floor
Second Floor
Third Floor
Roof
Parapet
Min. R-30 Flat andTapered Polyiso. FoamInsul. Board
1 2 3 4 5 6 7 8 9
2
El = 100'-0"
El = 114'-0"
El = 128'-0"
El = Varies
El = 146'-10"
4'-4" 18'-53/8" 11'-83/8" 9'-55/8" 9'-55/8" 11'-83/8" 18'-53/8" 4'-4"
5" Unreinf. Conc.Slab on Grade
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF on metaldeck re: Strl. (Typ.)
6" x 16 ga. Steel Studs at 16"O.C.
Acrylic Elastomeric Finish Coatover Acrylic Primer over 3/8"thick factory mixed cementitiousone coat stucco w/ acrylicpolymer admixture over 2.5 lb/sq.yd. self-furring diamond meshmetal lath over Tyvek CommercialWrap
5/8" Exterior Grade Gyp. Bd.Sheathing
R-19 FSK-Faced (Flame Spread25) Fiberglass Insulation
5/8" Gyp. Bd.(Level 5 FinishBelow Ceiling)
Refer to Window Schedule andWindow Types
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
Foundation per Strl.
Steel Frame per Strl.
Rigid Foam Cornice Profile
60 mil Fully AdheredEPDM Roof Membranew/ 16 mil Acrylic Coating
5" Unreinf. Conc.Slab on Grade
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF on metaldeck re: Strl. (Typ.)
Scale: 1/8" = 1'-0"
Building Section
First Floor
Second Floor
Third Floor
Roof
Parapet
Min. R-30 Flat andTapered Polyiso. FoamInsul. Board
1
5"
6 5
/8
"
11
5/
8"
2" 2"
8" 32" 8"
Acrylic Finish Coatover CementiousBase Coat
6" Steel Studs at 16" O.C.
R-19 Batt Insul.
3/4" Ext. GradePlywd.
Mudable U-Trim
Sealant
1/4" Shim Space
4" Brick Veneer w/Galv. CorrugatedWall Ties at 16"O.C. Horiz. & Vert.
Scale: 1 1/2"= 1'-0"
Pilaster DetailPlan View
1" Insulating Glass
5/8" Gyp. Bd.
Aluminum Framing -See Cut Sheets forFraming Section
Sealant overBacker Rod
Sealant overBacker Rod
1/2" Cement Backer Board
5/8" Ext. GradeGyp. Bd. Sheathing
15# Tyvek Stucco Wrap
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A11
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
456
1
12
R @
7" = 7
'-0
"1
2R
@ 7
" = 7
'-0
"1
2R
@ 7
" = 7
'-0
"1
2R
@ 7
" = 7
'-0
"1
2R
@ 7
" = 7
'-0
"1
3R
@ 7
" = 7
'-7
"
El = 100'
El = 107'
El = 114'
El = 121'
El = 128'
El = 135'
El = 142'-7"
1" Nosing (Typ.)
3'-23/16" 1'-33/8" 11'-111/2" 3" 2'-33/16"
3'-
0"
3'-
0"
6'-
8" H
ea
dro
om
3'-
0" (T
yp
.)
3'-
0" (T
yp
.)
61/8" 3'-21/4" 3'-21/4" 3'-21/4" 61/8"
1'-11" 2'-11/8" 35/8"
1'-11" 2'-11/8" 35/8"
3'-
0" (T
yp
.)
3'-
0" (T
yp
.)
51/2"
11/2" 4" 11/2"
1'-53/8"
11/2" 1'-37/8" 11/2"
51/2"
1 1/4" Std. PipeHandrail (Typ.)
Stair Pan SupportL1-1/2"x1-1/2" x3/16"x9" Lg.(2 per tread) welded to stringers
5" Unreinf. Conc.Slab on Grade
MC12x10.6 atperimeter of landing
Deck SupportL3"x3"x1/4" weldedto MC12x10.6
12 ga. Stair Pans w/Conc. Filled Treads
MC12x10.6 Stringers atea. side of Stair (Typ.)
4" Conc. Slab w/6x6-w2.1x2.1
WWF on metaldeck re: Strl.
4" Conc. Slab w/6x6-w2.1x2.1WWF on metaldeck re: Strl.
4" Conc. Slab w/6x6-w2.1x2.1WWF on metal deckre: Strl. (Typ.)
4" Conc. Slab w/6x6-w2.1x2.1WWF on metaldeck re: Strl.
4" Conc. Slab w/6x6-w2.1x2.1WWF on metal deckre: Strl. (Typ.)
Scale: 1/2" = 1'-0"
Stair Section
First Floor
Intermediate Landing
Second Floor
Intermediate Landing
Third Floor
Intermediate Landing
Uppermost Tread
Handrail EndElevationTypical AllLandings
Handrail EndElevationThird FloorIntermediateLanding Only
11 T @ 11" = 10'-1"
1'-
79
/1
6"
35/8" 3'-0" 12'-0" 1'-0" 2'-11/8" 35/8"
G H J
2
6A13
5A13
4A13
3A13
7A13
1A13
1A13
2A13
1A13
5A13
4A13
3A13
6A13
6A13
Elevator Shaft Stair Core
HVAC Shaft
Elevator Shaft Stair Core HVAC Shaft
Elevator Shaft Stair CoreHVAC Shaft
Scale: 1/2" = 1'-0"
Core Wall Section
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:05 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A12
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary6
5/8" Deflection Gap
5/8" Type "X" Gyp.Bd.
2 1/2" Sound BattInsul. Btwn Studs
Cont. 3 5/8" x 25Ga. Track w/ 21/2" Lg. Legs or 35/8" x 25 Ga. SlipTrack
3 5/8" x 25 Ga.Steel Studs @ 16"O.C.
5/8" Type "X" Gyp.Bd.
Cont. 3 5/8" x 25Ga. Track w/1 1/4"Lg. Legs
Spray AppliedFireproofing
HSS 8x8x3/8"Steel Tube (HSS7x7x3/8" & HSS6x6x3/8" Sim.)
2 1/2" Sound BattInsul. Btwn Studs
3 5/8" x 25 Ga.Steel Studs @ 16"O.C.
5/8" Type "X" Gyp.Bd.
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
5/8" Type "X" Gyp.Bd.
Scale: 3" = 1'-0"
Building Frame 2 & 4 Diag. Brace Detail
5
5/8" Deflection Gap
5/8" Type "X" Gyp.Bd.
2 1/2" Sound BattInsul. Btwn Studs
Control Joint
Cont. 3 5/8" x 25Ga. Track w/ 21/2" Lg. Legs or 35/8" x 25 Ga. SlipTrack
3 5/8" x 25 Ga.Steel Studs @ 16"O.C.
5/8" Type "X" Gyp.Bd.
Cont. 3 5/8" x 25Ga. Track w/1 1/4"Lg. Legs
Spray AppliedFireproofing
w 14 x 30 SteelBeam
2 1/2" Sound BattInsul. Btwn Studs
Control Joint
3 5/8" x 25 Ga.Steel Studs @ 16"O.C.
5/8" Type "X" Gyp.Bd.
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
Cont. 3" x 3" x 25ga Angle
Scale: 3" = 1'-0"
Building Frame 2 & 4 Floor Beam Detail7
5/8" Deflection Gap
L4 x 3 x 1/4 SteelAngle
Cont. 4" x 20 Ga.Track w/ 2 1/2"Lg. Legs or 4" x 20Ga. Slip Track
4" x 25 Ga. CH orCT Studs @ 24" O.C.
5/8" Type "X" Gyp.Bd.
1" Gyp. Bd. LinerPanel
4" Conc. Slab w/6x6-W2.1xW2.1WWF on 1.5VLI, 19ga. CompositeSteel Deck.
Spray AppliedFireproofing
w 8 x 10 SteelBeam
1 1/2" x 20 ga. ZClips w/ 2" Lg Horiz.Legs @ 16" O.C.
2 1/2" Sound BattInsul. Btwn Studs
Fire Resistive JointSpray over MineralWool FormingMaterial to Extend1/2" Below Min.Wool
Cont. 4" x 24 Ga. J-Track
4" x 25 Ga. CH orCT Studs @ 24" O.C.
5/8" Type "X" Gyp.Bd.
1" Gyp. Bd. LinerPanel
2 1/2" Sound BattInsul. Btwn Studs
Scale: 3" = 1'-0"
Shaft Wall/Floor Beam Detail (1)
3
5/8" Deflection Gap
Remove SprayAppliedFireproofing AsNeeded forElevator Threshold
L4 x 3 x 1/4 SteelAngle
Cont. 4" x 20 Ga.Track w/ 2 1/2"Lg. Legs or 4" x 20Ga. Slip Track
4" x 25 Ga. CH orCT Studs @ 24" O.C.
5/8" Type "X" Gyp.Bd.
1" Gyp. Bd. LinerPanel
4" Conc. Slab w/6x6-W2.1xW2.1WWF on 1.5VLI, 19ga. CompositeSteel Deck.
Spray AppliedFireproofing
w 12 x 14 SteelBeam
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
2 1/2" Sound BattInsul. Btwn Studs
Fire Resistive JointSpray over MineralWool FormingMaterial to Extend1/2" Below Min.Wool
Scale: 3" = 1'-0"
Shaft Wall/Floor Beam Detail
4
5/8" Deflection Gap
4" x 25 Ga. CH orCT Studs @ 24" O.C.
5/8" Type "X" Gyp.Bd.
2 1/2" Sound BattInsul. Btwn Studs
Control Joint
Cont. 4" x 20 Ga.Track w/ 2 1/2" Lg.Legs or 4" x 20 Ga.Slip Track
4" x 25 Ga. CH or CTStuds @ 24" O.C.
5/8" Type "X" Gyp.Bd.
1" Gyp. Bd. LinerPanel
1" Gyp. Bd. LinerPanel
Cont. 24 Ga. JTrack
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
Spray AppliedFireproofing
w 12 x 14 SteelBeam
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
2 1/2" Sound BattInsul. Btwn Studs
Fire Resistive JointSpray over MineralWool FormingMaterial to Extend1/2" Below Min.Wool
Cont. 2" x 2" x 25 gaAngle
Scale: 3" = 1'-0"
Shaft Wall/Floor Beam Detail
1
5/8" Deflection Gap
60 mil Fully AdheredEPDM RoofMembrane w/ 16mil Acrylic Coating
Cont. 4" x 20 Ga.Track w/ 2 1/2"Lg. Legs or 4" x 20Ga. Slip Track
4" x 25 Ga. CH orCT Studs @ 24" O.C.
5/8" Type "X" Gyp.Bd.
1" Gyp. Bd. LinerPanel
Min. R-30 Flat andTapered Polyiso.Foam Insul. Board
Spray-AppliedFireproofing
2 1/2" Sound BattInsul. Btwn Studs
Fire Resistive JointSpray over MineralWool FormingMaterial to Extend1/2" Below Min.Wool
1.5 B22 MetalRoof Deck
Mineral WoolForming Material inFlute Cavity
Scale: 3" = 1'-0"
Shaft Wall Detail @ Mechanical Shaft1-Hr. Fire Resistive Construction
2
5/
8"
60 mil Fully AdheredEPDM RoofMembrane w/ 16mil Acrylic Coating
Cont. 3 5/8" x 25Ga. Track w/2 1/2" Lg. Legs or3 5/8" x 25 Ga.Slip Track
3 5/8" x 25 Ga.Steel Studs @ 16"O.C.
5/8" Type "X" Gyp.Bd.
Min. R-30 Flat andTapered Polyiso.Foam Insul. Board
Spray-AppliedFireproofing
w 14 x 30 SteelBeam
1" x 20 ga. Z Clipsw/ 2" Horiz. Legs @16" O.C.
2 1/2" Sound BattInsul. Btwn Studs
1.5 B22 MetalRoof Deck
Paint Spray-AppliedFireProofing inStair Only
Cont. 3" x 3" x 25ga Angle
Control Joint
Cont. 3" x 3" x 25ga Angle
5/8" Type "X" Gyp.Bd.
Mudable J-Mould
Fire Sealant
Cont. 3" x 3" x 25ga Angle
Control Joint
Cont. 3" x 3" x 25ga Angle
Fire Resistive JointSpray over MineralWool FormingMaterial to Extend1/2" Below Min.Wool
Scale: 3" = 1'-0"
Building Frame 2 & 4 Roof Beam Detail
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:06 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A13
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
4
1A15
2A15
3A15
3'-
0"
6'-
0"
5'-
0"
3'-
0"
6'-
0"
5'-
0"
3'-
0"
6'-
0"
5'-
0"
1'-
4"
1'-
0"
El = 100'-0"
El = 114'-0"
El = 128'-0"
El = Varies
El = 144'-4"
14
'-0
"1
4'-
0"
Va
rie
sV
arie
s
6" x 16 ga. Steel Studs at 16"O.C.
Acrylic Elastomeric Finish Coatover Acrylic Primer over 3/8"thick factory mixed cementitiousone coat stucco w/ acrylicpolymer admixture over 2.5 lb/sq.yd. self-furring diamond meshmetal lath over Tyvek CommercialWrap
5/8" Exterior Grade Gyp. Bd.Sheathing
R-19 FSK-Faced (Flame Spread25) Fiberglass Insulation
5/8" Gyp. Bd.(Level 5 Finish Below Ceiling)
Refer to Window Schedule andWindow Types
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
Foundation per Strl.
Steel Frame per Strl.
EPS Insul. Cornice Profile
60 mil Fully AdheredEPDM Roof Membranew/ 16 mil Acrylic Coating
5" Unreinf. Conc.Slab on Grade
Scale: 1/2" = 1'-0"
Wall Section
Window Head
T.O. Roof Deck
Window Sill
Window Head
Window Sill
Window Head
Window Sill
T.O. Parapet
3rd Floor
2nd Floor
1st Floor
Wall Type "A"
Min. R-30 Flat andTapered Polyiso. FoamInsul. Board
5
5A15
14
'-0
"1
4'-
0"
Va
rie
sV
arie
s
El = 100'-0"
El = 114'-0"
El = 128'-0"
El = Varies
El = 144'-4"
2'-
0"
8"
4"
6'-
0"
8"
4"
3'-
4"
4"
1'-
4"
1'-
0"
12
'-0
"1
4'-
0"
1'-
4"
1'-
0"
1A11
6" x 16 ga. Steel Studs at 16"O.C.
4" Mod. Brick Veneer Pilaster w/Galv. Stl. Adjust. Wipe Ties at 16"O.C. Horiz. & Vert. (Typ. at RunningBond)
5/8" Exterior Grade Gyp. Bd.Sheathing
R-19 FSK-Faced (Flame Spread25) Fiberglass Insulation
5/8" Gyp. Bd.(Level 5 Finish Below Ceiling)
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
4" Conc. Slab w/ 6x6-w2.1x2.1 WWF onmetal deck re: Strl.
Foundation per Strl.
Steel Frame per Strl.
Rigid Foam Cornice Profile
60 mil Fully AdheredEPDM Roof Membranew/ 16 mil Acrylic Coating
5" Unreinf. Conc.Slab on Grade
EPS Insul. Capital Adheredw/ Cement. Adhes.
Acrylic Elastomeric Finish Coatover Acrylic Primer overfiberglass reinforcing meshembedded in 1/16" - 1/32"thickpolymer modifiedcementicious base coat over 2"thick expanded polystyreneinsulation (EPS) adhered w/above base coat to 3/8" thickfactory mixed cementitious onecoat stucco w/ acrylic polymeradmixture over 2.5 lb/sq. yd. self-furring diamond mesh metal lathover Tyvek Commercial Wrap
Back Wrap all EPS Shapes w/Fiberglass Reinforcing Mesh -Do Not Lap Mesh over One CoatStucco
Brick Rolock Course,Express 1/2"
1" Air Space
Brick Rolock Course, Express 1"and Chamfer top Corner at 45˚Angle
Brick Rolock Course, Express 1"and Chamfer top Corner at 45˚Angle
Brick Soldier Course,Express 1/2"
Brick Soldier Course,Express 1/2"
Weep Holes at 16" Horiz. AboveThrough Wall Flashing (2 perPilaster)
Scale: 1/2" = 1'-0"
Wall SectionWall Types "B" & "C"
T.O. Roof Deck
T.O. Parapet
3rd Floor
2nd Floor
1st Floor
Min. R-30 Flat andTapered Polyiso. FoamInsul. Board
4A15
3
Cont. 3 5/8" Stl. Track,Gauge to be same as Stl.Studs. Fasten track w/Powder Driven Pins
Suspended Acoustical TileCeiling (SAT)
5/8" type "X" gyp. bd. at ea. side(Verify w/ Wall Type)
3 5/8" 25 ga. Steel Studs @ 16"O.C.for walls less than 15'-5" inheight, 4" x 25ga. stl. studs @16" O.C. or 3 5/8" x 22ga. stl.studs @ 16" O.C. for wallsgreater than 15'-5" in height andless than 16'-5" in height
Brace top of wall w/ 3 5/8" x25ga. stl. studs @ 4'-0" o.c.staggered
Fasten braces @ top of wall w/screws
Fasten top of brace to bottom ofconc. tees w/ powder driven pins
Scale: 1/2" = 1'-0"
Typical Wall Section
2
Cont. 3 5/8" Stl. Track,Gauge to be same as Stl.Studs. Fasten track w/Powder Driven Pins
Suspended Acoustical TileCeiling (SAT)
5/8" type "X" gyp. bd. at ea. side(Verify w/ Wall Type)
3 5/8" 25 ga. Steel Studs @ 16"O.C.for walls less than 15'-5" inheight, 4" x 25ga. stl. studs @16" O.C. or 3 5/8" x 22ga. stl.studs @ 16" O.C. for wallsgreater than 15'-5" in height andless than 16'-5" in height
Scale: 1/2" = 1'-0"
Typical Wall Section
1
Cont. 3 5/8" Stl. Track, Gauge tobe same as Stl. Studs. Fastentrack w/ Powder Driven Pins
2 x 4 Fire Blocking
Suspended Acoustical Tile Ceiling(SAT)
5/8" type "X" gyp. bd. at ea. side(Verify w/ Wall Type)
Slip Joint at Top of Wall from 35/8" Deep Leg Stl. Track samegauge as Stl. Studs. Fasten w/Powder Driven Pins. Refer toWall/Ceiling Connection Details1-7, Sheet A12 of shell buildingdrawings for FirestopAssemblies if req'd by Bldg. Dept.
3 5/8" 25 ga. Steel Studs @ 16"O.C.for walls less than 15'-5" inheight, 4" x 25ga. stl. studs @16" O.C. or 3 5/8" x 22ga. stl.studs @ 16" O.C. for wallsgreater than 15'-5" in height andless than 16'-5" in height
Note:Where partition is required to be1hr. rated, refer to Table 720.1(2) item 13-1.1 2003 IBC.(0.018" (No. 25 carbon steelgage) channel-shaped studs 24"on center with one full layer of5/8" Type "X" gypsum wallboardapplied vertically attached with 1"long No. 6 drywall screws to eachstud. Screws at 8" on center atthe perimeter and 12" on centerat intermediate studs. Thewal lboard may be appliedhorizontally when attached to 35/8" studs and the horizontaljoints are staggered with thoseon the opposite side. Screws forthe horizontal application shall be8" on center at vertical edgesand 12" on center at intermediatestuds. Table 720.1(2)-item13-1.1)
Scale: 1/2" = 1'-0"
Typical Wall Section
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:06 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A14
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review
Prelim
inary
3
6"x1 1/4"x18 Ga(43 mills) Steel Track
1/2" Plywd. Shim
P.T. 2x6
Alum. Subsill w/ WeepHoles
Alum. Sill Flashing w/ 1/2"Hemmed Drip to Match Finishof Framing.
Framing Shim
2" x 4 1/2" ThermallyBroken Alum.Storefront Framing
Sealant overBacker Rod
Sealant over Backer Rod
Galv. Casing Bead
1" Insul. Glazing
6"x16 Ga (54 Mils)Steel Studs at 16" O.C.
Scale: 1 1/2"= 1'-0"
Window Sill Detail5
1/
2"
1'-
31
/2
"9
1/
4"
23
/4
"
1/
2"
1/
2"
51/8" 6"
45/8"
1"
6"x16 Ga (54 Mils)Steel Studs at 16" O.C.
Keep 1" Air Space Clear
Tyvek Comm. Wrap
4" Mod. Brick Veneer
Brick Rolock Course
EPS Insul. Capital Adheredw/ Cement. Adhes.
Acrylic Elasto. Fin. CoatOver Acrylic PrimerOver EIFS MeshEmbedded in 1/16" thickPoly. Mod. Cement. BaseCoat (Back Wrap EIFSMesh) Capital Sim.
Sealant over Backer Rod
Sealant over Backer Rod
24 Ga. Prefin. Galv. Stl.Tapered Cap Flashing
2" Thk. EPS Insul. Adheredw/ Cement. Adhes.
5/8" Ext. Gyp. Bd.Sheathing
5/8" P.T. Plywd
P.T. 2x4 Cleat
5/8" P.T. Plywd
Galv. Casing Bead
Turn Cap Flashing3" Min. Up Wall
20 Ga. Galv. Stl. Cleats atFront & Sides
P.T. 2x4 at Ea. Edge
Scale: 1 1/2"= 1'-0"
Wall Capital Detail
13
'-8
" A
bo
ve
1s
t F
loo
r
4
8" 4"
12"
6 5/8"1"
3 5/8"
11 1/4"
8"
6"x1 1/4"x18 Ga(43 mills) Steel Track
Adjust. Wire Ties at16" O.C. Horiz. & Vert.
6"x16 Ga (54 Mils)Steel Studs at 16" O.C.
Brick Ledge ShownDashed Where Required
Hemmed Drip at Flashing
Open Head Joint forWeep Holes at 16" O.C.
Through Wall Flashing
Tyvek Comm. Wrap, LapOver Through Wall Flashing
4" Mod. Brick Veneer
5" Unreinf. Conc.Slab on Grade
1/2" Exp. Jt. Mat'l
Scale: 1 1/2"= 1'-0"
Pilaster Detail (1)
2
Insulate Headerw/ 3 Pcs. 1 1/2"Thk. EPS Insul.
6"x1 1/4"x18 Ga(43 mills) Steel Track
Header From (3) 6"x2"x14 Ga. (68 Mils)Steel Studs Nestedinto 6"x11/4"x18Ga (43 Mils)Steel Track
1/2" Plywd. Shim
P.T. 2x6
Galv. Casing Bead w/Weep Holes
Alum. Head Flashing w/ 1/2"Hemmed Drip to Match Finishof Framing. Fasten VerticalFlange to Gyp. Bd. Sheathing
Framing Shim
2" x 4 1/2" ThermallyBroken Alum.Storefront Framing
Sealant overBacker Rod
Sealant over Backer Rod
Alum. Storefront FramingCompensating Channel
1" Insul. Glazing
Scale: 1 1/2"= 1'-0"
Window Head Detail
1
1'-
4"
91
/4
"2
3/
4"
6"
5"
Cont. Angle Re: Strl.
5/8" Ext. Gyp. Bd.Sheathing
Acrylic Elasto. Fin. Coatover Acrylic Primer Over3/8" Min. Thk. FactoryMixed Cement. One CoatStucco w/ AcrylicAdmixture over 2.5 Lb./Sq. Yd. Self-FurringDiamond Mesh Galv.Metal Lath Over TyvekComm. Wrap
Acrylic Elasto. Fin. Coatover Acrylic Primer OverEIFS Mesh Embedded in1/16" Thk. Poly ModifiedCement. Base Coat(Back Wrap EIFS Mesh)
Seam Plate w/ Fastenerat 12" O.C. Max.
EPS Insul. CrownMoulding Adhered w/Cement Base Coat
P.T. 2x4
24 Ga. Prefin. Galv. Stl.Tapered Coping
60 Mil TPOMembrane
6"x1 1/4"x18Ga (43 mills)Steel Track
5/8" P.T. Plywd.
6"x16 Ga (54Mils) Steel Studsat 16" O.C.
Steel Beam, Re:Strl.
1 1/2" Metal RoofDeck, Re: Strl.
(2) Layers 2 1/2"Thk. Polyiso. Insul.
1/2" P.T. Plywd.
(3) P.T. 2x6
Tapered Polyiso.Insul.
P.T. 2x4
5/8" P.T. Plywd.
12" Wide x 20 GaGalv. AnchorClips at 4'-0" O.C.
Scale: 1 1/2"= 1'-0"
Parapet Detail
1020 J
ohnson R
oad
Gold
en
, C
olo
rado
80219
Je
ffe
rso
n O
ffic
e P
ark
Offic
e B
uild
ing
Typ
e 3
Ha
eze
bro
uck &
Asso
cia
tes,
P.C
.A
rch
ite
cts
sheet
revision
Office Bldg 1020 2.pln Saved on 11/5/08
Printed on 11/5/08 at 10:06 PM
15
43
Su
nset
Rid
ge
Ro
ad
Hig
hla
nds R
anch
, C
olo
rado
8
012
6-2
681
30
3.4
70.7
87
2
FA
X 3
03
.470
.787
4j.f.h
aeze
bro
uck@
co
mca
st.
ne
t
of
A15
job JOP
DRF
JFH
drawn
checked
issued for9/15/08 Bid and Plan Review