New International Inc. Westco Productswpiwellkin.com/wp-content/themes/wellkin/pdf/Westco... ·...
Transcript of New International Inc. Westco Productswpiwellkin.com/wp-content/themes/wellkin/pdf/Westco... ·...
Westco Products International Inc.
www.westcoproductsintl.com Data subject to change without prior notice 2
About Service King Service King (SK) Manufacturing, Inc. is owned and operated by individuals with hundreds of years of combined rig building
experience. SK rig components are designed for fast rig-up and rig-down with versatility. There are several standard rig
options as well as custom orders for those with special requirements. All rigs meet or exceed oilfield industry standards.
Westco can also offer commissioning services as well as equipment packages to complement the rig. Rig options include
CAT engines, drilling or tubing line, sand line, winch line, auxiliary hydraulic winches, crown savers, mast lights, stand pipes,
engine guards, spark arrestor, walkways on off-operator side, hydraulic cylinder catheads installed in the mast, drilling
package (rotary drive, elevated drive, splitter box) and much more..
SK 175 Main Drum - Brakes: 38" x 8" forged steel, Chain:
#120 single, Clutch: Full air, Cooling: Spray water,
Grooving: 7/8" Lebus
Sand Drum - Brakes: 38" x 8" forged steel, Chain:
#120 single, Clutch: Full air, Capacity: 8900' of
9/16", 7200' of 5/8"
Carrier - Freightliner M2112, 3 or 4 axle
Frame - High tensile alloy steel wide flange beam,
Well service to 5000', Workover to 8000'
Derrick - 65' 12 x 14 Square Pole or 71' 150000 lb
Derrick
Transmission - 4500 Allison
SK 275 Main Drum - Brakes: 38" x 8" forged steel, Chain: #140 single,
Clutch: 224, Cooling: Spray water, Grooving: 7/8" Lebus
Sand Drum - Brakes: 38" x 8" forged steel, Chain: #140 single,
Clutch: 140, Capacity: 12500' of 9/16", 10000' of 5/8"
Carrier - 4 Axle - Front axle: 20000 lb capacity, Suspension: Spring,
Rear axle:46000 lb tandem double reduction, Suspension: Walking
beam, Front tires: 385/65R22.5, Front wheels: 12.25 x 22.5 duplex,
Rear tires: 11R22.5, Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to
8500', Workover to 7500'
Derrick - 71' 150000 lb capacity
Engine - Series 60 Detroit diesel
Transmission - 754 Allison
www.westcoproductsintl.com Data subject to change without prior notice 3
SK 375 Main Drum - Brakes: 38" x 10" forged steel, Chain: #140 single, Clutch:
224, Cooling: Spray water, Grooving: 7/8" or 1" Lebus
Sand Drum - Brakes: 38" x 8" forged steel, Chain: #140 single, Clutch: 124,
Capacity: 12500' of 9/16", 10000' of 5/8"
Carrier - 4 Axle - Front axle: 20000 lb capacity, Suspension: Spring, Rear
axle:46000 lb tandem double reduction, Suspension: Walking beam, Front
tires: 385/65R22.5, Front wheels: 12.25 x 22.5 duplex, Rear tires: 11R22.5,
Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to 12000',
Workover to 8000', Drilling to 5000' (3-1/2" drill pipe)
Derrick - 96' 180000 lb capacity
Engine - Series 60 Detroit diesel
Transmission - 754 Allison
SK 475 Main Drum - Brakes: 42" x 10" forged steel, Chain: #140 single, Clutch: 224,
Cooling: Spray water, Grooving: 1" or 7/8" Lebus
Sand Drum - Brakes: 38" x 8" forged steel, Chain: #140 single, Clutch: 124,
Capacity: 12500' of 9/16", 10000' of 5/8"
Carrier - 5 Axle - Front axle: 20000 lb capacity, Suspension: Spring, Rear
axle:46000 lb tandem double reduction, Suspension: Walking beam, Front
tires: 385/65R22.5, Front wheels: 12.25 x 22.5 duplex, Rear tires: 11R22.5,
Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to 14000',
Workover to 10000', Drilling to 6000' (3-1/2" drill pipe)
Derrick - 96' or 104' 250000 lb capacity
Engine - Series 60 Detroit diesel
Transmission - 754 Allison
SK 575 Main Drum - Brakes: 42" x 12" forged steel, Chain: 1-3/4" double,
Clutch: 324, Cooling: Spray water, Grooving: 1" Lebus
Sand Drum - Brakes: 42" x 8" forged steel, Chain: #140 double,
Clutch: 224, Capacity: 14400' of 9/16", 11800' of 5/8"
Carrier - 5 Axle - Front axle: 20000 lb capacity, Suspension: Spring,
Rear axle:46000 lb tandem double reduction, Suspension: Walking
beam, Front tires: 385/65R22.5, Front wheels: 12.25 x 22.5 duplex,
Rear tires: 11R22.5, Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to
18000', Workover to 14000', Drilling to 8000' (3-1/2" drill pipe)
Derrick - 96' to 109' 250000 lb capacity
Engine - Series 60 Detroit diesel
Transmission - 5610A Allison
www.westcoproductsintl.com Data subject to change without prior notice 4
SK 675 Main Drum - Brakes: 42" x 12" forged steel, Chain: #140 triple,
Clutch: 224 high torque, Cooling: Circulating water, Grooving: 1-
1/8" Lebus
Sand Drum - Brakes: 42" x 8" forged steel, Chain: #140 double, Clutch:
224, Capacity: 14400' of 9/16", 11800' of 5/8"
Carrier - 5 Axle - Front axle: 20000 lb capacity, Suspension: Spring,
Rear axle:46000 lb tandem double reduction, Suspension: Walking
beam, Front tires: 425/65R22.5, Front wheels: 12.25 x 22.5 duplex,
Rear tires: 11R22.5, Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to
18000', Workover to 14000', Drilling to 8000' (3-1/2" pipe)
Derrick - 104' 315000 lb capacity
Engine - Series 60 Detroit diesel
Transmission - 754 Allison
SK 775 Main Drum - Brakes: 42" x 12" forged steel, Chain: #140 triple,
Clutch: 224 high torque, Cooling: Circulating water, Grooving: 1-
1/8" Lebus
Sand Drum - Optional
Carrier - 6 Axle - Front axle: 20000 lb capacity, Suspension: Spring,
Rear axle:46000 lb tandem double reduction, Suspension: Walking
beam, Front tires: 425/65R22.5, Front wheels: 12.25 x 22.5 duplex,
Rear tires: 11R22.5, Rear wheels: 8.25 x 22.5 frame
Frame - High tensile alloy steel wide flange beam, Well service to
18000', Workover to 14000', Drilling to 8000' (4-1/2" pipe) / 10000'
(3-1/2" pipe)
Derrick - 112' 350000 lb capacity
Engine - (2) Series 60 Detroit diesel
Transmission - (2) 754 Allison
SK 1075 - 1000 HP mobile rig with 117' x 450000 lb capacity derrick, further information can be provided upon request
Substructures
Portable, Prefabricated - SK prefabricated substructures
are easily transported and provide various elevated work floors for
both workover and drilling operations. With load capacities up to
300 tons and clear heights ranging from 24' to 4', this large variety
of substructures is designed to meet multiple requirements.
One Piece, Fixed Height - These SK substructures provide a
simple work floor up to 12' high and are easily transported in a
minimum number of loads. Box-on-Box - These SK substructures provide more height for
larger wellheads and BOPs. The box-on-box design allows for
easier handling overall and lower transportation heights.
www.westcoproductsintl.com Data subject to change without prior notice 5
Derrick Specifications Model number 71-150 96-180 96-250 104-250 109-315 SK112-350 Height under crown 71' 96' 96' 104' 109' 112' Capacity (lbs) with 4 lines 150000 150000 180000 - - - with 6 lines - 180000 250000 250000 250000 - with 8 lines - - - - 315000 350000 Crown sheaves 3-24" 4-24" 4-24" 4-24" 1-30"&4-24" 1-36"&4-30" Sand line sheave 1-24" 1-24" 1-24" 1-24" 1-24" Optional Racking Singles Doubles Doubles Doubles Doubles Doubles Platform elevation 25' 55' 55' 55' 55' 60' Capacity (ft) 2-3/8 EUE 12500 25000 25000 25000 25000 30000 2-7/8 EUE 9000 18000 18000 18000 18000 22000 2-7/8 DP - 15000 15000 15000 15000 18000 3-1/2 DP - - - 12500 12500 15000 Rod hanger Doubles Triple Triple Triple Triple NA Elevation 54'-3" 78'-6" 78'-6" 78'-6" 78'-6" NA Capacity (ft) 10400 15600 15600 15600 15600 NA Raising cylinder One One Two Two Two Two Telescoping cylinder One One One One One Two
Rig Packages Westco can also offer commissioning services as well as equipment packages to complement the rig. These packages include:
Mud pumps
Mud equipment
Mud tanks
Power swivels
Choke and kill manifolds
BOPs
Drilling spools
Closing units
Handling tools
Tubing blocks
Hook blocks
Rod hooks
Rotary swivels
Rotary tables
Hex or square Kelly
Kelly valves
Drill pipe and drill collars
Instrumentation
Generator sets
Air compressors
Light towers
Hand tools
Safety equipment
Trailers
On request, Westco can provide the other material needed by the customer to perform the job.
www.westcoproductsintl.com Data subject to change without prior notice 6
About Universe Machine Universe Machine Corporation is a family run business that has been in
operation for over 40 years. Their mission is to work with customers,
employees and suppliers in an honest and fair manner using the best
technology to provide products at a competitive price. They accomplish
this goal with a highly skilled workforce including machinists, welders,
millwrights, technicians and engineers.
Tubing Power Tong Maximum Maximum Weight Body Torque Maximum Size (in) Torque (ft-lb) (lbs) Dimensions (in) Arm (in) Speed (rpm) 4.50 12500 750 23 x 34.3 24 107 5.50 15000 850 24.5 x 37.1 26 100
2 jaw biting system with wrap around dies will not scar or deform the tubing.
Optional non-marking system for chrome tubular is available.
Rugged spur gear system provides high torque.
2 position, high/low, torque and speed control.
Casing Power Tong Maximum Maximum Weight Body Torque Maximum Size (in) Torque (ft-lb) (lbs) Dimensions (in) Arm (in) Speed (rpm) 9.63 22000 1075 28.5 x 43 30 83 13.38 25000 1175 31.7 x 48.9 32 75 17.00 30000 1800 39 x 56 36 70 20.00 35000 2250 43.7 x 71 42 57 24.5 40000 3550 49.7 x 79.7 48 49
3 jaw biting system with 6 dies will not scar or deform the casing.
Rugged spur gear system provides high torque.
2 position, high/low, torque and speed control.
Coker Drum Drill Tong with Hydraulic Backup Maximum Maximum Weight Body Dimensions (in) Maximum Size (in) Torque (ft-lb) (lbs) Length x Width x Height Speed (rpm) 9.63 25000 2000 49.38 x 32.25 x 74 83
Use proven equipment to properly breakout and torque drill stem joints.
3 jaw biting system with 6 dies will not scar or deform the drill stem.
Minimize downtime and increase safety.
2 position, high/low, torque and speed control.
Optional Tong Equipment Options available include custom sizes, alternate power trains, manual or hydraulic backup, lift cylinder, torque gauge, bi-directional load cell and door safety interlock.
www.westcoproductsintl.com Data subject to change without prior notice 7
Hydraulic Backup Maximum Maximum Weight Body Dimensions (in) Size (in) Torque (ft-lb) (lbs) Width x Height x Depth 6.00 15000 650 26.1 x 33.5 x 31.5 6.00 25000 675 26.1 x 33.5 x 31.5 10.63 25000 690 32.3 x 35.8 x 30.5 14.38 25000 925 36.5 x 36.5 x 30.5 18.00 30000 1225 41.8 x 39.5 x 30.5 21.00 35000 1525 46.8 x 44.3 x 30.5 25.50 40000 1900 52.8 x 47.0 x 30.5
Radial Load Eliminator minimizes the joint friction and eliminates axial twist.
Bi-directional load cell able to measure torque in both directions.
Tri-bite Link three jaw system for an optimum bite.
Dual size capability bites casing or coupling with the same jaw set.
Friction-Bite Unit Maximum Minimum Maximum Weight Body Dimensions (in) Size (in) Size (in) Torque (ft-lb) (lbs) Width x Depth x Height 5.50 2.06 15000 184 16.6 x 17.5 x 13.5 9.63 2.38 22000 215 21.5 x 23.0 x 13.5
Can be mounted onto a open mouth power tong.
The jaws are completely interchangeable with the power tong, which reduces tool-up costs.
Power requirements: 80-120 psi compressed air.
Kelly Spinners Type Maximum Weight Power Maximum Torque (ft-lb) (lbs) Requirements Speed (rpm) Air 1050 750 1-8 CFS / 90-150 psi 170
Mounted to bottom of swivel eliminating the need for dangerous spinning chain.
Can be driven in forward or reverse.
Spark free operation.
Closed Mouth Power Tong Maximum Maximum Weight Body Torque Maximum Size (in) Torque (ft-lb) (lbs) Dimensions (in) Arm (in) Speed (rpm) 7.00 13000 1100 18 x 48 40 134 11.75 18500 2390 24 x 58 47 100
All gear power train.
2 position, high/low, torque and speed control.
Utilizing standard jaw and drag ring systems.
www.westcoproductsintl.com Data subject to change without prior notice 8
About Hawk Industries For over 50 years, Hawk Industries has been a leader
in the design and manufacture of specialty tools used
in the oil well industry. Committed to remaining an
industry leader, Hawk continually updates their
facilities and equipment. For the production of the
highest quality parts, their facility employs
computerized equipment, including CNC lathes, mills
and plasma cutter.
T-Wrex Senior Remotely Operated Make/Break System
Torque Tool Joints Spinner Hydraulic Air Dimensions Weight (ft-lb) Size Range Size Range Power Power (in) (lbs) 100000 4.0"- 9.5" OD 3.5"- 9.5" OD 3000 psi@35 GPM 100 psi@10 cfm 53.5 Wide 8500 66.5 Long Retracted
Head tilt of ± 15 degrees. 120.3 Long Extended
Rotation up to 270 degrees. 96.1 High Minimum
Spins and torques in under 15 seconds in most applications. 134.1 High Maximum
T-Wrex Junior Remotely Operated Make/Break System
Torque Tool Joints Spinner Hydraulic Air Dimensions Weight (ft-lb) Size Range Size Range Power Power (in) (lbs) 60000 make 3.5"- 8.0" OD 3.5"- 8.0" OD 3000 psi@35 GPM 100 psi@10 cfm 43.5 Wide 7500 80000 break 62.2 Long Retracted
Head tilt of ± 15 degrees. 134.3 Long Extended
Rotation up to 270 degrees. 86.6 High Minimum
Spins and torques in under 15 seconds in most applications. 124.6 High Maximum
www.westcoproductsintl.com Data subject to change without prior notice 9
HAWKJAW Senior Drill Pipe Power Tong Torque Tool Joints Spinner Hydraulic Air Dimensions (in) Weight (ft-lb) Size Range Size Range Power Power Width x Length x Height (lbs) 100000 4.0"- 9.5" OD 3.5"- 9.5" OD 3000 psi@35 GPM 100 psi@10 cfm 56.1 x 60.0 x 101.5 4000
HAWKJAW Junior Drill Pipe Power Tong Torque Tool Joints Spinner Hydraulic Air Dimensions (in) Weight (ft-lb) Size Range Size Range Power Power Width x Length x Height (lbs) 60000 make 3.5"- 8.0" OD 3.5"- 8.0" OD 3000 psi@35 GPM 100 psi@10 cfm 47.8 x 43.0 x 93.5 2700 80000 break
SPINMASTER Drill Pipe Spinner Pipe Size Maximum Maximum Hydraulic Dimensions (in) Weight Range (in) Torque (ft-lb) Speed (rpm) Power W x L x H (lbs) Model 650 2-7/8 to 600 to 130 to 2000 psi 21 x 28 x 45 500 5-1/2 1085 70 @20 GPM Model 950 2-7/8 to 600 to 130 to 2000 psi 22 x 36 x 45 575 9-1/2 1972 39 @20 GPM
Note: Available with pneumatic or hydraulic drive.
www.westcoproductsintl.com Data subject to change without prior notice 10
About BVM
BVM Corporation is the one source for rig handling tools.
Tongs Type Torque (ft-lb) Size (in) Manual "SDD" 100000 4 to 17 Manual "DB" 65000 3-1/2 to 17 Manual "B" 55000 3-1/2 to 13-3/8 Casing "B" 25000 13-3/8 to 36-1/2 Manual "C" 35000 2-3/8 to 10-3/4
Type Torque (ft-lb) Size (in) Manual "LF" 16000 2-3/8 to 8-5/8 Manual "MS" 6500 6-1/8 to 19 Manual "BV-F-2500" 5000 2-1/16 to 3-1/2 Manual "AAX" 55000 2-7/8 to 13-3/8 Manual "H" 80000 3-1/2 to 13-3/8
Links Type Rating (ton) Size (in) Workover 150 1-3/4x36 to 1-3/4x120 Elevator 250 2-1/4x60 to 2-1/4x144 Elevator 350 2-3/4x60 to 2-3/4x240 Elevator 500 3-1/2x108 to 3-1/2x264 Elevator 750 4-3/4x120 to 4-3/4x216
Type Rating (ton) Size (in) Electroweld 20 7/8x18 to 7/8x24 Electroweld 50 1-1/4x26 to 1-1/4x72 Electroweld 60 1-1/2x24 to 1-1/2x36 Electroweld 80 1-3/4x30 to 1-3/4x84 Electroweld 100 2x42 to 2x96
Elevators Slip Type Type Rating (ton) Size (in) "LYT" 20 1.050 to 2-1/16 "YT" 75 1.315 to 3-1/2 "YC" 75 3-1/2 to 7 "MYC MOD." 125 3-1/2 to 7 18° Center Latch Type Rating (ton) Size (in) "MG" 100 2-3/8 to 5 "RG" 150 2-3/8 to 5 "RG" 175 3-1/2 to 5-1/2 "MGG" 250 3-1/2 to 5-1/2 "GG" 350 3-1/2 to 5-1/2 90° Collar Type Center Latch Type Rating (ton) Size (in) "TA" 35 1.050 to 2-7/8 "TA" 65 1.660 to 2-7/8 "TA" 65 3-1/2 to 4-1/2 "TA" 100 2-3/8 to 2-7/8 "TA" 100 3-1/2 to 4-1/2 "TA" 100 4-3/4 to 8-5/8 "TA" 150 4-1/2 to 8-5/8 "RA" 125 2-3/8 to 3-1/2
Safety Clamps Types T, C, MP-S, MP-R, MP-M, MP-L, MP-XL
90° Collar Type Center Latch, Continued Type Rating (ton) Size (in) "RA" 150 3-1/2 to 5-1/2 "RA" 175 3-1/2 to 5-1/2 "RA" 250 3-1/2 to 7 "RA" 350 4-1/2 to 7 90° Collar Side Door Type Rating (ton) Size (in) "SLX" 100 3-1/2 to 5-1/2 "SLX" 150 6-5/8 to 20 "SLX" 250 6-5/8 to 30 "SX" 350 9-5/8 to 20 "SX" 500 9-5/8 to 20 Single Joint Type Rating (ton) Size (in) "BV-S" 5 2-3/8 to 24-1/2 Sucker Rod Type Rating (ton) Size (in) "SR" 20 5/8 to 3/4 "SR" 20 3/4 to 7/8 "SR" 20 1 "SR" 20 1-1/8 "SRP" 20 5/8 to 1
Slips Rotary Type Size (in) 3-1/2 to 5-1/2 Short/Medium 2-3/8 to 5-1/2 4-1/2 to 7 Long 3-1/2 to 7 Casing Type Size (in) CMSXL 5-1/2 to 30 CMS "Conductor Pipe" 24 to 30
Type Size (in) UC-3, 13-3/8 to 36 11-3/4 to 36 Drill Collar Type Size (in) DCS-S 3 to 4-7/8 DCS-R 4-1/2 to 7 DCS-L 5-1/2 to 14
Elevator/Spider Type Size (in) 200 Ton 2-3/8 to 7-5/8 350 Ton 4-1/2 to 14 500 Ton 4-1/2 to 14
Type Size (in) 500 Ton 16 to 24-1/2 750 Ton 6-5/8 to 14 750 Ton 16 to 24-1/2
www.westcoproductsintl.com Data subject to change without prior notice 11
About Westco Products International Westco Products International (WPI) was established in an effort to serve the growing demand for quality well servicing,
workover and drilling equipment. The personnel at WPI have over 40 years of industry experience.
Open Head Tubing Power Tong Model Maximum Maximum Weight Body Dimensions (in) Torque Maximum Size (in) Torque (ft-lb) (lbs) Length x Width x Height Arm (in) Speed (rpm) 45000 4.75 6670 620 31 x 43 x 26 23 96 55000 4.75 8740 620 31 x 43 x 26 23 101 56000 4.75 11750 620 31 x 43 x 26 23 76
Options:
Manual or pneumatic backup
Torque load cell
Closed Head Tubing Power Tong Model Maximum Maximum Weight Body Dimensions (in) Torque Maximum Size (in) Torque (ft-lb) (lbs) Length x Width x Height Arm (in) Speed (rpm) 58-93R 7 6000 1000 51 x 22 x 32 23 96
Options:
Manual or pneumatic backup
Hydraulic lift cylinder
Power Sucker Rod Tong Model Maximum Maximum Weight Maximum Size (in) Torque (ft-lb) (lbs) Speed (rpm) M20 1-1/8 1290 363 130 M40 1-1/8 1620 363 105 M50 1-1/8 2040 363 80
Tubing Spider Model Maximum Minimum Capacity Weight Size (in) Size (in) (ton) (lbs) G 4.50 1.660 60 320 C 5.50 1.315 82.5 408 CHD 5.50 1.315 125 457
Hydraulic Power Unit Model Prime Mover Tong Circuit and Capacity 30000 114 HP Diesel Tubing, 3000 PSI @ 25 GPM Casing, 1000 PSI @ 75 GPM 30100 60 HP Electric Tubing, 3000 PSI @ 19 GPM Casing, 1000 PSI @ 62 GPM 30200 50 HP Electric Tubing, 2500 PSI @ 19 GPM
Note:
Custom power units available upon request.
www.westcoproductsintl.com Data subject to change without prior notice 12
Equipment
Mobile Workover Rigs
Mobile Drilling Rigs
Tubing Tongs
Tubing Spiders
Rod Tongs
Power Units
Casing Tongs
Kelly Spinners
Make-up/Break-out System
Drill Pipe Tong
Drill Pipe Spinners
Manual Tongs
Links
Elevators
Elevator/Spiders
Safety Clamps
Slips
BOPs
Spools, DSAs, Studs, Nuts
Ring Gaskets
Closing Units
Choke and Kill Manifolds
Gate Valves, Adj./Fixed/Drilling Chokes
Rotary Tables
Fishing Tools
Tubing Blocks
Drilling Hooks
Rotary Swivels
Power Swivels
Mud Pumps
Mud Tanks and Equipment
Light Towers
Drill Collars
Drill Pipe
Pup Joints, Crossovers, Lift Subs
Kelly - Hex/Square, Valves, Inside BOPs
Rotating, Mud, Hydraulic Hoses
Generator Sets
Air Compressors
Instrumentation (Weight, Tong Torque)
Hammer Unions and Swivels
Safety Equipment
Chain tongs, impact wrenches, hand tools
Rotating Heads
Rod Hooks, Wrenches
Equipment Spares
Rig Brake Blocks, Bands, Clutches, Lebus Shells, Parts
Tong Dies, Jaws and Parts
Spider Inserts, Slips and Parts
Mud Pump Expendables and Parts
BOP Ram Blocks and Ram Seals
BOP Bladders
BOP Seal Kits
Hook and Block Parts
Engine Spares
Swivel Washpipes, Packing and Parts
Kelly Roller Parts
Elevator Parts
Services
Rig Commissioning
Custom engineering/design and fabrication
Contact Information
Westco Products International, Inc.
8401 Industrial Dr.
Pearland, TX 77584
PH: (281) 992-2064
FX: (281) 992-2076
E-Mail: [email protected]
Web: www.westcoproductsintl.com
International Agents
Indonesia
Pt. VarcoINDO Bina Jaya Contact: Abdi Gustino
Russia
Cognitive Technologies (UK) Limited Contact: Alexander Astakhov
Peru
ONPA S.A. Contact: Fernando Oneto