new boidata

6
CURRICULUM VITAE MAHENDRA PRATAP SINGH UP (INDIA) Email: [email protected] Mob. No. 08454874014, Home - 09795326714 [email protected] I have total 12 years’ experience in construction of Oil/Gas/ Power Plant/Petrochemical Project. I work offshore in Qatar and 8 years Gulf experience in DOHA, DUBAI, & SAUDI. Professional Profile: -Good technical background with experienced in co-ordination, control, Supervising in per-commissioning, commissioning activities for mechanical stationary and rotating equipment, solid practical knowledge in lube oil, Seal oil flushing ,cccw ,stator cooling water h2 gas cooling , Checking Pump & Compressor for over speed tests. .Steam Blowing & Protections and interlocks setting. Pipe line chemical cleaning in power generation plant/oil/gas plant. -Able to works on own initiative in a multi-disciplined team, ability to work under pressure the activities with tight schedules necessitating extra hours, capability in supervising units operation under critical and emergency situations. Tanks Repair Mechanical Mantinea’s Mantinea’s Sell & Bottom Plate. Follow ting tanks Rapier in sill /changing sill. Repair nosel & nosel pad, Changing / Repair Rolling Weal ladder Pin and stapes. Change lag support pin and gas kit. Change /Repair the foliating ruff drain Pipe & slinging PIPING ACTIVETY: Possess excellent knowledge of Piping Plan, G.A., Isometric, P & ID, Planning daily progress work activities. Coordinate with QC Department and other department to speed up the Progress. Ability to work, under pressure. Effectively controlling Manpower related Piping Fabrication, Erection and Hydro testing. Per plan for Post Applied For: Mechanical

Transcript of new boidata

Page 1: new boidata

CURRICULUM VITAE

MAHENDRA PRATAP SINGH UP (INDIA)Email: [email protected] Mob. No. 08454874014, Home - [email protected]

I have total 12 years’ experience in construction of Oil/Gas/ Power Plant/Petrochemical Project.I work offshore in Qatar and 8 years Gulf experience in DOHA, DUBAI, & SAUDI.

Professional Profile:

-Good technical background with experienced in co-ordination, control, Supervising in per-commissioning, commissioning activities for mechanical stationary and rotating equipment, solid practical knowledge in lube oil, Seal oil flushing ,cccw ,stator cooling water h2 gas cooling , Checking Pump & Compressor for over speed tests. .Steam Blowing & Protections and interlocks setting. Pipe line chemical cleaning in power generation plant/oil/gas plant.

-Able to works on own initiative in a multi-disciplined team, ability to work under pressure the activities with tight schedules necessitating extra hours, capability in supervising units operation under critical and emergency situations.

Tanks Repair Mechanical Mantinea’s

Mantinea’s Sell & Bottom Plate. Follow ting tanks Rapier in sill /changing sill. Repair nosel & nosel pad, Changing / Repair Rolling Weal ladder Pin and stapes. Change lag support pin and gas kit. Change /Repair the foliating ruff drain Pipe & slinging

PIPING ACTIVETY:

Possess excellent knowledge of Piping Plan, G.A., Isometric, P & ID, Planning daily progress work activities. Coordinate with QC Department and other department to speed up the Progress.Ability to work, under pressure. Effectively controlling Manpower related Piping Fabrication, Erection and Hydro testing. Per plan for material, and men power before start side works. Responsibilities to check the material certificate material chemical composition. Coordinate with engineering department for technical quarry. To monitor the activities as per project spec and procedure. Preparing and conducting arrangement for hydro test as per test pack. Co-ordinate with immediate superior regarding work site, work schedule, access and Equipments required for the job

Codes & Standards:-

Exposure to ASME, ANSI, API, ASTM

Post Applied For: Mechanical Engineer

CODE CONPETENCIES

Page 2: new boidata

JOB EXPERIENCE SUMMARY

1- Previous Employment

Hyundai heavy industries (Saudi)Mechanical commissioning Engineer (11 Jan 2016 to---)

Duties & Responsibilities Duties included mechanical operation & maintenance activities for turbine lube oil, seal oil, stouter cooling water, h2 gas cooling, and hued spray, jacking oil, cccw, auxiliary boiler, water treatment plant and condensed polishing plant.Supervising and participate in the preventive, corrective and troubleshooting maintenance (day/night covering 24 hours shift schedule maintenance),identifies source of problems, diagnosing, repairing faults, discuss and initiates action quickly and efficiently, continuous maintains radio contact and mobile phone for any emergency with shift area operators in Main BMS room.

My duties including also day to day work planning activities, close monitoring and preparation of daily works progress report, completes the work orders in Computerized Maintenance Management System with materials, manpower, ensures that spare parts and the required materials are ordered available and in good condition before starting maintenance activity in accordance with planned operations and maintenance schedules, arranges the transportation of materials to site and resolve problems with personnel mechanical technicians in respect of Safety.

2-Previous Employment

Arabian Bemco Contracting Co .L.T.D. (Saudi) Mechanical commissioning Engineer (22 Dec 2014 to 29 June 2015)

Duties & Responsibilities

Responsible for the site mechanical construction activities for Facility Mechanical (12 hours rotating day/night shift schedule),supervising prepares and assists in preparation with commissioning responsibility, pressure test, leak testing, hydro test, flushing, blowing up, punch list, commissioning check lists, arranges equipment testing, coordinate between different pipeline activities of workers engaged in installing, assembling or fitting work (BS,SS, GI, Copper and PVC), pipe-racks erection, pipe-trench and sleeper racks, piping system fixtures, hangers and supports installation ensuring work is carried out in accordance with relevant Codes, Standards and Procedures in respect of Safety, marking and checking weld maps on isometrics, insulation requirement, make progress reports.

Supervising the installation and testing mechanical stationary and rotating equipment in the plant, (booster pumps, compressors), verify rotating machine, monitoring daily the installation site constructions multidisciplinary mechanical activities such as: Pump house piping, Potable Cold & Hot Water System, Storm Water System, Sanitary System; Fire Suppression System, Upright sprinkler, Pendent sprinkler, connection Alarm Gong, Retard Chamber, Alarm Check Valve, Pressure Reducing Valve (PRV),Non Return Valve (NRV), Relief Valve, Flow Switch, 2/4 Way Breeching Inlet (Naffco), Tamper Switch (Potter),Supervisory Switch (Potter),Assembly Valve,

COMPANY WORK PROFILE

Page 3: new boidata

3 -Previous Employment

Target Engineering const.co. L.T.D. (Abu Dhabi) Mechanical Engineer (17 August2012 to 15 August 2013)

Duties & Responsibilities

Responsible for the safe and efficient tests commissioning of 5 Gas Turbine (GE) LM 6000 and auxiliary system such as: Oil Systems with Lube Oil, Power Oil and Jacking Oil, Closed Cooling Water System for the Lube Oil and Generator Cooling; Cooling Air Systems on the Gas Turbine, Filters house and Air Intake, Exhaust System; Water and N2 Purge Systems, Sound Enclosure and Ventilation Systems; Fire Fighting Systems and Gas Detection; including also responsible for the Fuel Gas and Fuel Oil Systems such as: Gas Metering, Scrubber and Filters, Gas Heater and Pressure Reducing Stations and Gas Compressors; Fuel Oil Metering and Forwarding Station, Loading/Unloading Storage Tank System.

Employed as a Commissioning Mech. Engineer I have performed pre-commissioning and commissioning activities: Walk down Inspection, Punch List, Work Request Sheet, Data Sheet Preparing; Commissioning Check List Site, Pre-start-up, conformity Checks and Static tests execution.

Coordinating mechanical commissioning team to carry out all jobs, according to GE Commissioning recommended procedures: Blowing up-air line, Pressure test, Filling up & hydro test-auxiliary, Leak test, Water cooling line, Flushing Synthetic/Mineral lube oil line-hydraulic oil line, field supervision and verification of installed equipment, hydraulic pump, fans, air compressors, air blowers, gas compressors, monitoring and inspection of alignment pipelines by the drawings, install support on the line, prepare pipeline for fit up; prefabrication in Workshop executed by Contractor (IMCO)and other power plant related works.

Implementing Start-up, Normal, Shut Down operations and emergency handling at plant field as per operation manuals; start, stop and switch rotary machinery as per operating schedule or checking-up results in the plant units, training course of Understanding & Activities for safety rules in Plant Operation, implementing knowledge of all mechanical team about Fire Fighting and Disaster Prevention.

Hand over to the operation team the units in full confidence and with required safety.

4-Previous Employment . Overseas Construction co. (Qatar) Mechanical Engineer (12 April 2012 to 03 Jun 2012)

Duties & ResponsibilitiesCo-ordinate with immediate superior regarding work site, work schedule, access and Equipments required for the job. Pre -planning for the tools & tackles, welding machines, & other tools.Arrangement of all document (Drawings, DWR, WPS, & F/UP records for site & site office.Conducting the meetings with all supervising staff safety procedure, Erection F/UP, Welding Procedure to follow the safety & Quality Procedure. Carry on the job as per isometric, GA & Plan. If there is any mismatch or clash, Writing the technical query and proposal also. Mantinea’s exchanger, visual, Coolum

5-Previous Employment

Global Engineering Qatar LLC (Qatar) Mechanical Engineer (08 July 2008 to 02 February 2012)

Page 4: new boidata

Duties & ResponsibilitiesProcess good knowledge of piping isometric drawing, support drawings piping plan.Supervise piping & supports fabrication and erection. Allocating welder & fitters to respective job as per their qualification & skill. Attending punch list and clearing it. Coordinate with QC for inspection and NDT .Conducting the meetings with all supervising staff (safety procedure, Erection F/UP, Welding Procedure to follow the safety &Quality Procedure. Carry on the job as per isometric, GA & Plan. If there is any mismatch or clash, Writing the technical query and proposal also.

TRAINING & SEMINAR: 100% tie off fall protection. Job hazard analysis Confined space operation H2S/BA Course ( Descon) Offshore training

EDUCATIONAL QUALIFICATION: H, S.C. PASSED.

TECHNICAL QUALIFICATION: B tech in Mechanical Engineering

PERSONAL DETAILS: Name : Mahendra pratap singh

Father's Name : Sri Surya bhan singhDate of birth : 02/07/1983Place of birth : Kushinager (U.P.)Sex : MaleNationality : IndianReligion : HinduMarital Status : Unmarried Language Known : English, HindiPermanent Address : Village. Kharitwa, Post. Churaipali

Dist. Kushinager (U.P.) INDIAContact No. : 09795326714.

PASSPORT DETAILS:Passport No. : M 1083285 Date of Issue : 13/08/2014Date of Expiry : 12/08/2024Place of Issue : Luck nowOld Passport No. : G 3182714(Expired)

I hereby declare that all the above mentioned details are true and accurate to the best of my knowledge.

Best Regards.

(Mahendra pratap singh)