Networking devices
-
Upload
rehnuma-rusha -
Category
Engineering
-
view
141 -
download
3
Transcript of Networking devices
![Page 1: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/1.jpg)
Local Area Networks - Internetworking
1
![Page 2: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/2.jpg)
Internetworking devices
2
Increasing power and complexityHubsBridgesSwitchesRouters
![Page 3: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/3.jpg)
3
Why Interconnect?
•To separate / connect one corporate division with another.
•To connect two LANs with different protocols.
•To connect a LAN to the Internet.
•To break a LAN into segments to relieve traffic congestion.
•To provide a security wall between two different types of users.
•To connect WLAN to LAN
![Page 4: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/4.jpg)
4
Introduction
Many times it is necessary to connect a LAN to another LAN or to a WAN.
Computers within a LAN are often connected using a hub
LAN to LAN connections are often performed with a bridge.
Segments of a LAN are usually connected using a switch.
LAN to WAN connections are usually performed with a router.
![Page 5: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/5.jpg)
5
Hubs
A hub interconnects two or more workstations into a local area network.
When a workstation transmits to a hub, the hub immediately resends the data frame to all connecting links.
Hubs expand one Ethernet connection into many. For example, a four-port hub connects up to four machines
![Page 6: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/6.jpg)
Hubs
![Page 7: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/7.jpg)
7
Bridge
A bridge connects networks and forwards frames from one network to another.
BRIDGE
A B
C D
E F
G H
PORTS
![Page 8: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/8.jpg)
8
Selective Forwarding
If A sends a frame to E - the frame must be forwarded by the bridge.
If A sends a frame to B - there is no reason to forward the frame.
BRIDGE
A B
C D
E F
G H
![Page 9: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/9.jpg)
9
Bridge Database The bridge needs a database that contains
information about which hosts are on which network.
The realistic options are:The system administrator can create and maintain
the database. The bridge can acquire the database on the fly.
Hard to
add
new co
mputers
Some loss of efficiency
![Page 10: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/10.jpg)
10
Bridge interconnecting two identical LANs
![Page 11: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/11.jpg)
11
A bridge interconnecting two dissimilar LANs
![Page 12: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/12.jpg)
12
Learning the host mapping
The bridge forwards packets for which it does not know network destination.
Every time the bridge forwards a packet it records the network on which the sender is located.
![Page 13: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/13.jpg)
13
Transparent Bridges
A transparent bridge does not need programming but observes all traffic and builds routing tables from this observation.
This observation is called backward learning.
Each bridge has two connections (ports) and there is a routing table associated with each port.
A bridge observes each frame that arrives at a port, extracts the source address from the frame, and places that address in the port’s routing table.
A transparent bridge is found with CSMA/CD LANs.
![Page 14: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/14.jpg)
14
Source-routing Bridges
A source-routing bridge is found with token ring networks.
Source-routing bridges do not learn from watching tables.
When a workstation wants to send a frame, it must know the exact path of network / bridge
If a workstation does not know the exact path, it sends out a discovery frame.
The discovery frame makes its way to the final destination, then as it returns, it records the path.
![Page 15: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/15.jpg)
15
Remote Bridges
A remote bridge is capable of passing a data frame from one local area network to another when the two LANs are separated by a long distance and there is a wide area network connecting the two LANs.
A remote bridge takes the frame before it leaves the first LAN and encapsulates the WAN headers and trailers.
When the packet arrives at the destination remote bridge, that bridge removes the WAN headers and trailers leaving the original frame.
![Page 16: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/16.jpg)
Bridges vs RoutersBridge: A bridge is a
device that connects two segments of the same network. The two networks being connected can be alike or dissimilar.
Bridges are protocol-independent. They simply forward packets without analyzing and re-routing messages.
Router: A router is a device that connects two distinct networks. Routers are similar to bridges, but provide additional functionality, such as the ability to filter messages and forward them to different places based on various criteria.
The Internet uses routers extensively to forward packets from one host to another.
16
![Page 17: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/17.jpg)
17
SwitchesA switch is a combination of a hub and a bridge.
It can interconnect two or more workstations, but like a bridge, it observes traffic flow and learns.
When a frame arrives at a switch, the switch examines the destination address and forwards the frame out the one necessary connection.
![Page 18: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/18.jpg)
18
Switches
Major role: isolating traffic patterns and providing multiple access. This design is usually done by the network manager.
Switches are easy to install and have components that are hot-swappable.
![Page 19: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/19.jpg)
19
Switches
The backplane of a switch is fast enough to support multiple data transfers at one time.
Multiple workstations connected to a switch use dedicated segments. This is a very efficient way to isolate heavy users from the network.
![Page 20: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/20.jpg)
Switches vs routers
20
Switches are considered layer-two devices, using MAC addresses to forward frames to their proper destination. Routers, layer-three devices, are much more complex, using microprocessor-based circuitry to route packets between networks based on their IP address. Routers provide the following services: route discovery; selection of the best route to a destination; adaptation to changes in the network; translation from one technology to another, such as Ethernet to token ring; packet filtering based on IP address, protocol, or UDP/TCP port number; and connection to a WAN.
Because of the additional processing required for each packet, a router has a higher latency than a switch. In addition, a router requires an initial set-up sequence, in which the ports are programmed and certain protocols and characteristics are enabled or disabled. A switch may be simply plugged into the network, automatically learning how to forward frames as the network is used. Note that some protocols (e.g., NetBEUI) can’t be routed; instead, they will pass through a switch. Finally, switches are used within networks to forward local traffic intelligently. Routers are used between networks to route packets between networks in the most efficient manner.
![Page 21: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/21.jpg)
21
Workstations connected to a shared segment of a LAN
![Page 22: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/22.jpg)
22
Workstations connected to a dedicated segment of a LAN
![Page 23: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/23.jpg)
23
A Switch with Two Servers Allowing Simultaneous Access to Each Server
![Page 24: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/24.jpg)
24
A server with two NICs and two connections to a switch
![Page 25: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/25.jpg)
25
A pair of remote bridges and switch combinationdesigned to isolate network traffic
![Page 26: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/26.jpg)
26
Switch providing multiple access to an e-mail server
![Page 27: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/27.jpg)
27
Full Duplex Switches
A full duplex switch allows for simultaneous transmission and reception of data to and from a workstation.
This full duplex connection helps to eliminate collisions.
To support a full duplex connection to a switch, two sets of wires are necessary - one for the receive operation and one for the transmit operation.
![Page 28: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/28.jpg)
28
Full duplex connection of workstations to a LAN switch
![Page 29: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/29.jpg)
29
Network Servers
Network servers provide the storage necessary for LAN software.
They are usually the focal point for the network operating system.
Increasingly, network servers are functioning as bridges, switches, and routers. By adding the appropriate card, a server can assume multiple functions.
![Page 30: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/30.jpg)
30
Routers (really specialized computers)
The device that connects a LAN to a WAN or a WAN to a WAN (the INTERNET! – uses IP addresses).
A router accepts an outgoing packet, removes any LAN headers and trailers, and encapsulates the necessary WAN headers and trailers.
Because a router has to make wide area network routing decisions, the router has to dig down into the network layer of the packet to retrieve the network destination address.
![Page 31: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/31.jpg)
31
Routers
Thus, routers are often called “layer 3 devices”. They operate at the third layer, or OSI network layer, of the packet.
Routers often incorporate firewall functions.
An example of a router’s operation is shown on the next slide.
![Page 32: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/32.jpg)
Wireless connections: Access Point as a Bridge
32
![Page 33: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/33.jpg)
33
Connections (in general)
Bridges for LANs and hubs.
Switches for LANs and workstations.
Routers for LANs and WANs (the Internet).
![Page 34: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/34.jpg)
Linksys Router for Home Network
34
![Page 35: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/35.jpg)
The OSI Reference Model
35
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
![Page 36: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/36.jpg)
The Physical Layer Connection
36
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
Specifies Specifies electrical electrical
connectionconnection
![Page 37: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/37.jpg)
The Physical Layer Connection
37
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
Hub
AmplificationAmplificationRegenerationRegeneration
![Page 38: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/38.jpg)
The Data Link Connection
38
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayerDelineationDelineation
ofofDataData
ErrorErrorDetectionDetection
AddressAddressFormattingFormatting
![Page 39: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/39.jpg)
39
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
Bridge& Switch
The Data Link Connection
![Page 40: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/40.jpg)
The Network Layer Connection
40
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayerEnd to end End to end
routingrouting
![Page 41: Networking devices](https://reader030.fdocuments.us/reader030/viewer/2022032422/55a8a0b81a28ab40718b4590/html5/thumbnails/41.jpg)
The Network Layer Connection
41
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
NetworkLayer
Data LinkLayer
PhysicalLayer
ApplicationLayer
PresentationLayer
SessionLayer
TransportLayer
Router