Network Standard - Ausgrid · NS119 Public Lighting Design and Construction Amendment No 3...

NW000-S0037 UNCONTROLLED IF PRINTED of 61

Network Standard

NETWORK

Document No Amendment No Approved By Approval Date Review Date

: : : : :

NW000-S0037 3 Head of AEP & S 30/08/2018 30/08/2021

Supersedes Network Standard (Network) NW000-S0037 Amendment No.2

NW000-S0037 NS119 PUBLIC LIGHTING DESIGN AND CONSTRUCTION

NS119 Public Lighting Design and Construction

Amendment No 3


ISSUE

For issue to all Ausgrid and Accredited Service Providers’ staff involved with public lighting work, and is for reference by field, technical and engineering staff.

Ausgrid maintains a copy of this and other Network Standards together with updates and amendments on www.ausgrid.com.au.

Where this standard is issued as a controlled document replacing an earlier edition, remove and destroy the superseded document

DISCLAIMER

As Ausgrid’s standards are subject to ongoing review, the information contained in this document may be amended by Ausgrid at any time. It is possible that conflict may exist between standard documents. In this event, the most recent standard shall prevail.

This document has been developed using information available from field and other sources and is suitable for most situations encountered in Ausgrid. Particular conditions, projects or localities may require special or different practices. It is the responsibility of the local manager, supervisor, assured quality contractor and the individuals involved to make sure that a safe system of work is employed and that statutory requirements are met.

Ausgrid disclaims any and all liability to any person or persons for any procedure, process or any other thing done or not done, as a result of this Standard.

All design work, and the associated supply of materials and equipment, must be undertaken in accordance with and consideration of relevant legislative and regulatory requirements, latest revision of Ausgrid’s Network Standards and specifications and Australian Standards. Designs submitted shall be declared as fit for purpose. Where the designer wishes to include a variation to a network standard or an alternative material or equipment to that currently approved the designer must obtain authorisation from the Network Standard owner before incorporating a variation to a Network Standard in a design.

External designers including those authorised as Accredited Service Providers will seek approval through the approved process as outlined in NS181 Approval of Materials and Equipment and Network Standard Variations. Seeking approval will ensure Network Standards are appropriately updated and that a consistent interpretation of the legislative framework is employed.

Notes: 1. Compliance with this Network Standard does not automatically satisfy the requirements of a Designer Safety Report. The designer must comply with the provisions of the Workplace Health and Safety Regulation 2011 (NSW - Part 6.2 Duties of designer of structure and person who commissions construction work) which requires the designer to provide a written safety report to the person who commissioned the design. This report must be provided to Ausgrid in all instances, including where the design was commissioned by or on behalf of a person who proposes to connect premises to Ausgrid’s network, and will form part of the Designer Safety Report which must also be presented to Ausgrid. Further information is provided in Network Standard (NS) 212 Integrated Support Requirements for Ausgrid Network Assets.

2. Where the procedural requirements of this document conflict with contestable project procedures, the contestable project procedures shall take precedent for the whole project or part thereof which is classified as contestable. Any external contact with Ausgrid for contestable works projects is to be made via the Ausgrid officer responsible for facilitating the contestable project. The Contestable Ausgrid officer will liaise with Ausgrid internal departments and specialists as necessary to fulfil the requirements of this standard. All other technical aspects of this document which are not procedural in nature shall apply to contestable works projects.

INTERPRETATION

In the event that any user of this Standard considers that any of its provisions is uncertain, ambiguous or otherwise in need of interpretation, the user should request Ausgrid to clarify the provision. Ausgrid’s interpretation shall then apply as though it was included in the Standard, and is final and binding. No correspondence will be entered into with any person disputing the meaning of the provision published in the Standard or the accuracy of Ausgrid’s interpretation.

KEYPOINTS

This standard has a summary of content labelled “KEYPOINTS FOR THIS STANDARD”. The inclusion or omission of items in this summary does not signify any specific importance or criticality to the items described. It is meant to simply provide the reader with a quick assessment of some of the major issues addressed by the standard. To fully appreciate the content and the requirements of the standard it must be read in its entirety.

AMENDMENTS TO THIS STANDARD

Where there are changes to this standard from the previously approved version, any previous shading is removed and the newly affected paragraphs are shaded with a grey background. Where the document changes exceed 25% of the document content, any grey background in the document is to be removed and the following words should be shown below the title block on the right hand side of the page in bold and italic, for example, Supersedes – document details (for example, “Supersedes Document Type (Category) Document No. Amendment No.”).

KEY POINTS OF THIS STANDARD


Design and Purchase Install and Commission Maintain and Refurbish Scope and Risks Addressed

Tools and Forms Annexure FG

Tools and Forms Annexure E

Annexure G Sample Compliance Checksheet

This standard details the design, construction, maintenance and refurbishment requirements for street lights within the scope identified below:

Applies to all the street lighting systems that are to be owned and operated by Ausgrid on behalf of the Street Lighting Customer.

All materials and equipment to be free from Asbestos and or asbestos related products.

Privately owned street lights not installed on Ausgrid assets.

Where to for more information? Section 1.0.0,2.0.0

The design requirements identified include:

Ausgrid will supply information on current low voltage and street lighting assets in the project area.

Electrical designers must be accredited and authorised to ASP Level 3, for contestable works.

Basic design requirements including clearances to other assets, interconnection to existing assets and design concepts to be used in each Ausgrid region.

Voltage, protection isolation and control requirements outlined.

Special requirements for the lighting design and compliance with Australian Standards identified.

Only approved equipment listed in Annexure C are to be used in the design.

Design documentation to comply with requirements of NS104 Specification for Electrical Network Project Design Plans.

Non-standard equipment may be used if approved by following NS 181 Approvals request process.

Equipment may be purchased through Ausgrid stores.

The installation and commission requirements include:

The electrical designer is responsible for providing local authorities and the RMS with copies of proposed construction plans as detailed in Section 10.

Street lighting poles must be installed in compliance with NS 128 Specification for pole installation and removal.

Installation of fittings in accordance with specified requirements.

Commissioning checks and tests listed.

Maintenance and refurbishment requirements include.

Luminaire markings to facilitate identification and maintenance

Special requirements relating to the replacement of pedestrian crossing floodlights.

Requirements relating to replacement of failed luminaires.

A street lighting pole screen kit is required for live work on steel or concrete lighting poles.

Users of the kit to be qualified by undertaking the SS1100 Jointers Low Voltage Work and Screen course.

Use of frangible poles is not approved.

Tools and Forms Annexure B,C,D,E

Where to for more information? Section 5.0.0, 6.0.0

Where to for more information? Section 7.0.0 ,8.0.0 ,0.0

Where to for more information? Section 10.0.0, 11.0.0, 12.0.0


Amendment No 3


Network Standard NS119

Public Lighting Design and Construction

Contents

PURPOSE ............................................................................................................................................. 7 1.0

SCOPE .................................................................................................................................................. 7 2.0

REFERENCES ...................................................................................................................................... 7 3.03.1 Ausgrid documents .................................................................................................................... 7 3.2 Other standards and documents ................................................................................................ 8 3.3 Acts and regulations................................................................................................................... 8

DEFINITIONS ........................................................................................................................................ 9 4.0

DESIGN ............................................................................................................................................... 11 5.05.1 Electrical design ....................................................................................................................... 11

5.1.1 Electrical design information ........................................................................................ 11 5.1.2 Qualification of the electrical designer ......................................................................... 11 5.1.3 Clearances between installed street lighting equipment and exposed conductors ..... 11 5.1.4 Replacement of pillar standards ................................................................................... 11 5.1.5 Overhead supplied street lighting system .................................................................... 11 5.1.6 Underground supplied street lighting system ............................................................... 12

5.2 Lighting design ......................................................................................................................... 17 5.2.1 Lighting design brief ..................................................................................................... 17 5.2.2 Qualification of the lighting designer ............................................................................ 17 5.2.3 Australian standard compliance ................................................................................... 17 5.2.4 Street lighting equipment ............................................................................................. 17 5.2.5 Lighting of cul-de-sacs ................................................................................................. 17 5.2.6 Placement of steel lighting poles .................................................................................. 17 5.2.7 Rag-bolt mounted steel lighting poles .......................................................................... 18 5.2.8 Pedestrian crossing lighting ......................................................................................... 18 5.2.9 Poles with ‘pole mounted substations’ ......................................................................... 18 5.2.10 Decorative lighting ........................................................................................................ 18 5.2.11 Painting of street lighting furniture ................................................................................ 18

5.3 Approved street lighting equipment list .................................................................................... 19 5.3.1 Photometric data for luminaires ................................................................................... 19

5.4 Design documentation ............................................................................................................. 19

EQUIPMENT AND PURCHASING ...................................................................................................... 20 6.06.1 Equipment specifications ......................................................................................................... 20 6.2 Approved equipment list .......................................................................................................... 20 6.3 Approval of non-standard equipment ....................................................................................... 20 6.4 Purchase materials through Ausgrid Stores ............................................................................ 20 6.5 Asbestos .................................................................................................................................. 20

TRANSPORT ....................................................................................................................................... 20 7.07.1 Transport of poles .................................................................................................................... 20 7.2 Transport of lamps ................................................................................................................... 20 7.3 Transport of luminaires ............................................................................................................ 20


Amendment No 3


INSTALL .............................................................................................................................................. 21 8.08.1 Construction planning .............................................................................................................. 21 8.2 Installation of steel lighting poles ............................................................................................. 21

8.2.1 Finished ground levels ................................................................................................. 21 8.3 Installation of bracket arms ...................................................................................................... 21 8.4 Installation of pole wiring .......................................................................................................... 21 8.5 Labelling of street lighting assets ............................................................................................. 21 8.6 Data capture ............................................................................................................................. 21

COMMISSION ..................................................................................................................................... 21 9.09.1 Commissioning checks / tests .................................................................................................. 21

MAINTAIN ............................................................................................................................................ 22 10.010.1 Luminaire markings including lamp shape ............................................................................... 22 10.2 Pedestrian crossing floodlights ................................................................................................ 22 10.3 Spot maintenance .................................................................................................................... 22 10.4 Removal of overhead street lighting circuits ............................................................................ 23

10.4.1 Incidental work ............................................................................................................. 23 10.5 Replacement of existing luminaires ......................................................................................... 23

Category P - Roadway Reserve Width (RRW) > 12m ................................................. 23 10.5.1 Category P - Roadway Reserve Width (RRW) <= 12m ............................................... 24 10.5.2 Category V ................................................................................................................... 25 10.5.3

REFURBISH ........................................................................................................................................ 26 11.011.1 Street lighting pole screening kit .............................................................................................. 26

REPLACE ............................................................................................................................................ 27 12.012.1 Use of frangible poles .............................................................................................................. 27

RECORDKEEPING ............................................................................................................................. 27 13.0

AUTHORITIES AND RESPONSIBILITIES .......................................................................................... 27 14.0

DOCUMENT CONTROL...................................................................................................................... 27 15.0

ANNEXURE A PRIVATELY OWNED STREET LIGHTS .......................................................................... 28 A.1 Not installed on Ausgrid assets ................................................................................................ 28 A.2 Recording of connections to the Ausgrid network ................................................................... 28

ANNEXURE B EQUIPMENT SPECIFICATIONS ...................................................................................... 29 B.1 Warning .................................................................................................................................... 29 B.2 Specification for steel lighting poles, bracket arms and rag bolt assemblies........................... 29 B.3 Specification for street lighting equipment (luminaires, lamps and control gear) .................... 29

ANNEXURE C APPROVED EQUIPMENT LIST ....................................................................................... 30 C.1 Wood poles .............................................................................................................................. 30 C.2 Steel lighting poles ................................................................................................................... 30 C.3 Bracket arms ........................................................................................................................... 33 C.4 Prestigious lighting system ..................................................................................................... 34 C.5 Rag bolt assemblies ................................................................................................................ 34 C.6 Outreach extension arm .......................................................................................................... 35 C.7 Insulating spigots .................................................................................................................... 35 C.8 Other insulating brackets ........................................................................................................ 35 C.9 Non-insulating spigots ............................................................................................................. 36 C.10 Steel pole link panels .............................................................................................................. 36 C.11 Luminaires ............................................................................................................................... 37 C.12 Lamps ..................................................................................................................................... 43


Amendment No 3


C.13 Photo-electric cells .................................................................................................................. 47 C.14 Miscellaneous ......................................................................................................................... 47

ANNEXURE D OTHER REFERENCE CONSTRUCTION ........................................................................ 48 D.1 Prestigious lighting system ...................................................................................................... 48 D.2 Underground Residential Distribution (URD) street lighting options ........................................ 49

ANNEXURE E SPARE PARTS FOR MAINTENANCE OF LEGACY STREET LIGHTS .......................... 51 E.1 Steel lighting poles ................................................................................................................... 51 E.2 Strengthening sleeve ............................................................................................................... 51 E.3 Insulating spigots ..................................................................................................................... 51 E.4 Legacy luminaires .................................................................................................................... 52 E.5 Luminaire spare parts .............................................................................................................. 52 E.6 Chokes, boxes and panels ....................................................................................................... 56

ANNEXURE F LIST OF AUSGRID DRAWINGS ...................................................................................... 58

ANNEXURE G SAMPLE COMPLIANCE CHECK SHEET ........................................................................ 60


Amendment No 3


PURPOSE 1.0

This Network Standard specifies Ausgrid’s requirements for the design and construction of all public lighting assets that are to be owned and operated by Ausgrid on behalf of Ausgrid’s Public Lighting Customers. The requirements of this Standard shall apply throughout Ausgrid’s supply area for contestable and non-contestable projects.

SCOPE 2.0

This Network Standard shall apply to all public lighting installations which are to be owned and operated by Ausgrid on behalf of Ausgrid’s Public Lighting Customers. Where a public lighting project is deemed contestable, the Customer shall use an Accredited Service Provider to complete the electrical design, illumination design and construction work. Refer to Ausgrid’s Electricity Supply document ES4 Accredited Service Provider Authorisation.

For information on privately owned public lighting installations i.e. installations which are not owned and operated by Ausgrid, refer to Annexure A.

REFERENCES 3.0

3.1 Ausgrid documents Bush Fire Risk Management Plan Company Form (Governance) - Network Document Endorsement and Approval

Company Procedure (Network) - Production / Review of Network Standards

Company Procedure (Governance) - Network Document Endorsement and Approval

Customer Installation Safety Plan Electrical Safety Rules Electricity Network Safety Management System Manual ES 4 Accredited Service Provider Authorisation

NS100 Field Recording of Network Assets

NS104 Specification for Electrical Network Project Design Plans

NS110 Design and Construction Standard for URDs

NS122 Pole Mounted Substation Construction

NS124 Specification for Overhead Connections (100 to 400 Amps)

NS127 Specification for Low Voltage Cable Joints and Terminations

NS128 Specification for Pole Installation and Removal

NS130 Specification for Laying of Underground Cables up to 11kV

NS148 Overhead Line Support, Street Light Column, Pit and Pillar Numbering

NS161 Specification for Testing of Underground Cables

NS167 Positioning of Poles and Lighting Columns

NS181 Approval of Materials and Equipment and Network Standard Variations

NS183 Installation of Private Attachments on Ausgrid Poles

NS199 Safe Electrical Working on Low Voltage Assets

NS212 Integrated Support Requirements for Ausgrid Network Assets

NS224 Low Voltage Suburban Commercial and Industrial Underground Distribution Utilising Pillars

NS261 Requirement for Design Compliance Framework for Network Standards

Public Electrical Safety Awareness Plan Public Lighting Management Plan Tree Safety Management Plan


Amendment No 3


3.2 Other standards and documents AS/NZS 1158 series - Lighting for roads and public spaces

AS/NZS 1477 PVC pipes and fittings for pressure applications

AS/NZS 1798 Lighting Poles and Bracket Arms - Preferred Dimensions

AS/NZS 3100 Approval and test specification – General requirements for electrical equipment

AS/NZS 4026 Electric cables – For underground residential distribution systems

AS/NZS 4677 Steel utility service poles

AS/NZS 7000 Overhead Line Design – Detailed procedures

AS 2700 Colour standards for general purposes

AS 4282 Control of the obtrusive effects of outdoor lighting

ENA Doc 001-2008 National Electricity Network Safety Code

WorkCover Code of Practice for work near overhead power lines

3.3 Acts and regulations Electricity Supply (General) Regulation 2014 (NSW)

Electricity Supply (Safety and Network Management) Regulation 2014

Electricity Supply Act 1995

Work Health and Safety Act 2011

Work Health and Safety Regulation 2017 (NSW)


Amendment No 3


DEFINITIONS 4.0

Ausgrid Ausgrid is an electricity distribution authority pursuant to the NSW Government Gazette No. 70 of 30 June 1993.

Accredited Service Provider (ASP)

An individual or entity accredited by the NSW Department of Planning and Environment, Energy, Water and Portfolio Strategy Division, in accordance with the Electricity Supply (Safety and Network Management) Regulation 2014 (NSW).

Business Management System (BMS)

Ausgrid’s integrated policy and procedure framework that contains the approved version of documents.

Contestable Works

The design, construction and installation of electricity works, which are required to connect a customer’s installation to an electricity network. Customers are required to fund the cost of contestable work and they have the choice of selecting the Accredited Service Provider (ASP).to carry out the work.

Customer A customer may be a developer or a Street Lighting Customer.

Dedicated Street Lighting Circuit

An electrical circuit that supplies only street lights from a street light control point (SLCP). Overhead supplied dedicated street lighting circuits are progressively being made redundant.

Document control

Ausgrid employees who work with printed copies of document must check the BMS regularly to monitor version control. Documents are considered “UNCONTROLLED IF PRINTED”, as indicated in the footer.

Electrical Designer

An Ausgrid employee, contractor to Ausgrid or authorised Level 3 Accredited Service Provider who is duly qualified to produce electrical design plans.

Lighting Designer

A Lighting Designer is qualified by training and experience to undertake Australian Standard compliant lighting designs. The Lighting designer may be engaged by an Accredited Service Provider.

Luminaire The street light fitting. The luminaire normally consists of the lamp, reflector, control gear (including a photoelectric control switch), etc all included in a protective case with a glass or plastic visor.

Network Standard

A document, including Network Planning Standards, that describes the Company's minimum requirements for planning, design, construction, maintenance, technical specification, environmental, property and metering activities on the distribution and transmission network. These documents are stored in the Network Category of the BMS repository.

Pillar Standard A steel street lighting column with an enlarged lower section which could incorporate a link panel/bi-form connectors/tri-form connectors and providing for the connection of services.

Review date The review date displayed in the header of the document is the future date for review of a document. The default period is three years from the date of approval however a review may be mandated at any time where a need is identified. Potential needs for a review include changes in legislation, organisational changes, restructures, occurrence of an incident or changes in technology or work practice and/or identification of efficiency improvements.

RMS Roads and Maritime Services, a NSW Government agency.

Service Pillar An insulated pillar whose primary function is to serve as a connection point for the consumer’s mains supplying one or more installations. It also has provision for supplying community facilities such as street lighting.


Amendment No 3


Street Lighting Customer

The Body controlling the area to be lit and responsible for the applicable Street Lighting charges, eg Local Councils.

Steel Lighting Pole

The steel support structure for an underground supplied street light. It normally consists of a pole with an outreach arm.


Amendment No 3


DESIGN 5.0

5.1 Electrical design

5.1.1 Electrical design information For contestable works, Ausgrid shall provide the electrical designer electrical design information with sufficient details to prepare the electrical design.

Detailed design of street lighting requirements must use the types of cables, pillars and other electrical equipment specified in this and other referenced Standards.

5.1.2 Qualification of the electrical designer An electrical designer shall be an accredited and authorised Level 3 Accredited Service Provider, for Ausgrid contestable works.

5.1.3 Clearances between installed street lighting equipment and exposed conductors

Ausgrid Electrical Safety Rules details the clearances required between installed public lighting components and exposed conductors. These clearances must be adhered to.

Where erected on a timber pole using LVABC, the streetlight shall be erected so that no rubbing of the LVABC conductor insulation or protective sheath shall occur on the bracket or luminaire.

5.1.4 Replacement of pillar standards If a luminaire at an existing pillar-standard is no longer required because of the new design, the pillar-standard is to be replaced by a distribution pillar, see NS 127. Where this occurs, rag-bolts must be cut off below the level of the pre-cast pillar base.

5.1.5 Overhead supplied street lighting system Connection to low voltage mains shall be in accordance with NS 124.

Streetlights installed on wood poles shall be single insulated and not earthed, relying on the insulating properties of the wood to provide additional protection for workers and the public.

Luminaires shall be directly connected to the overhead low voltage mains via two core 2.5mm2 PVC insulated and PVC sheathed cable and individually controlled by a photoelectric cell. The cable shall be run in flexible PVC conduit which is firmly attached to the pole by galvanised saddles fixed in place with galvanised screws or clouts. Supply to the street light must not be taken from any dedicated street lighting circuits which are switched circuits, and which will be progressively made redundant. Drawings TBA show installation details for LVABC and bare wire connections.

Existing overhead pole mounted construction will remain as is unless substantial work is required on the installation – e.g. mains brought down in a storm.

Individual street lights shall be protected by means of a 10A HRC fuse. Installations that require a new street lighting bracket to be installed must contain the fuse at the base of the bracket. Refer to drawing B1-66251 for details of street lighting bracket range. Fuse arrangements are shown on each brackets specific drawing listed in Table C3.

Existing installations that have a fuse installed as an attachment on the pole or contained within external control gear box mounted on the pole are acceptable legacy installations only if the bracket does not require replacement. For retrofit situations only an inline fuse may be placed inside the luminaire.

In circumstances where a luminaire is being replaced that has external control gear mounted on the pole, this control box may be used to house the fuse for the replacement luminaire. However care shall be taken to bypass any existing control gear i.e. ballast and ignitor. If the control box is not being used it shall be removed from the pole.


Amendment No 3


Street lighting loads must be balanced over the three distributor phases. The electrical designer must indicate on the low voltage/street lighting plan the phase to which each luminaire is to be connected.

5.1.6 Underground supplied street lighting system

5.1.6.1 Double insulated street lighting system Ausgrid in the past has had a legacy issue of double insulated systems being utilised in the Sydney and Central Coast regions and a single insulated and earthed system in the Hunter regions. This has required different equipment and construction standards to be applied. This amendment removes this requirement and has standardised equipment and construction based on the double insulated system.

All new and replacement installations on steel structures within Ausgrid’s network area shall be constructed using the double insulated system.

The sections below detail how construction shall be carried out across Ausgrid’s entire network area. Drawing TBA shows standard construction for underground supplied installations.

5.1.6.2 Cabling For street lights that are near the underground low voltage network, a standalone arrangement is required. Supply must extend from the nearest pillar using approved two core 16mm2 copper XLPE insulated and PVC sheathed cable to the street lighting link panel in the base of the pole. Approved link panels are detailed in section 5.1.6.3. Two core 2.5mm2 copper PVC insulated and PVC sheathed cable shall extend from the base of each steel lighting pole to each luminaire. If the low voltage network does not extend to the location of the lights, a maximum of three lights may be looped between street light poles from a single phase of a service pillar and there is no requirement for fuse protection at the pillar.

Where the low voltage network does not extend to the location of the lights for circuits that contain four or more lights, a dedicated street lighting circuit is required. A looped arrangement supplied by a circuit of approved four core 16mm² copper XLPE insulated and PVC sheathed cable and street light control point (SLCP) pillar is required. Refer to NS127 for the SLCP pillar arrangement. Two core 2.5mm2 copper PVC insulated and PVC sheathed cable shall extend from the base of the steel lighting pole to each luminaire.

For dedicated street lighting circuits, lighting loads must be balanced over the three distributor phases. The electrical designer must indicate on the low voltage/street lighting plan the phase to which each luminaire is to be connected. For four-core cable, all cores shall be terminated at each pole so that the lamp may be connected to any phase in the future.

In areas where the street light (SL) cable has deteriorated, rather than replacing the SL cable, where practical the lights shall be connected to LV mains.

The installation must comply with the requirements of NS 130. In particular, the cable must be taken from the pillar into the same trench as the LV distributor to a point at right angles to the steel lighting pole and then directly to the pole.

New or replacement installations of street lighting cables shall not have underground tee joints. If it is necessary for a tee connection to be made in a street lighting circuit (for example, to enable a branch in the circuit), the tee connection must be made at an appropriate link panel in a steel lighting pole or at a dedicated connection pillar.

The electrical designer shall ensure that the cables meet the load and voltage drop limits for the particular project.

5.1.6.3 Link Panels All connections made at the base of a steel lighting standard shall be made on an appropriate link panel. Table 1 – Link Panels below details link panels that are approved for use on Ausgrid’s network.


Amendment No 3


Table 1 – Link Panels

Stock Code

Description Drawing Number

Pre Wired Notes

66845 Small link panel with single fuse A1-62525 No Panel to be used on

standards 6.5m or less with single streetlight

183985 Large link panel with single fuse A1-62525 No

Panel to be used on standards 7.5m or greater with single streetlight. Best used where SL circuit loops

in and out at panel

183986 Large link panel with double fuse A1-62525 No Panel to be used on

standard columns 7.5m or greater with dual streetlights.

150797 Large link panel with single fuse A1-228838 Yes

Panel to be used on standard columns 7.5m or

greater with single streetlight. Best used when directly connected to a pillar and no looping is required

Where the insulating panel is supplied by the manufacturer with components pre-wired, the pre-wired cables on the panel shall be SDI (single double insulated - white sheathed) cable.

The cables on the insulating panel shall be tied to each other in such a way that if any one cable becomes detached from its termination it is retained in position. This is a requirement so that the live conductor cannot come into contact with either the panel or the metal pole. Figure 1 demonstrates how this is achieved on the pre-wired version of the available link panels.

The incoming cable:

shall be an approved double insulated (i.e. sheathed) cable up to the cable saddle, and

shall be fixed under the saddle, and

shall have all single insulated coloured cores continuously mounted on the surface of, and within the perimeter of the insulating panel.

All cores are to be colour identified. The phase order of neutral, A, B and C (Black, Red, White, Blue) shall be maintained at the terminal block.

The outgoing street lighting cable:

shall be an approved double insulated (i.e. sheathed) two core cable, and

shall have both the basic and supplementary (sheath) insulation layers stripped back only as far as necessary, and

shall be saddled to the clip provided on the insulating panel, and

shall have both the neutral and active cores terminated in the two-way terminal block.

It is not acceptable to terminate the active core at the fuse holder terminal.

Figure 1 demonstrates an appropriately wired link panel.


Amendment No 3


Figure 1 - Pre Wired Link Panel


Amendment No 3


5.1.6.4 Voltage limits The installation should be designed so that no lights will normally be operating outside the voltage range of 230 Volts +10% and -6%. This will be achieved within the low voltage design, if the street lighting circuit or low voltage distributor to which street lights are attached is designed in accordance with NS 110.

5.1.6.5 Protection Where underground supplied street lights are supplied from a dedicated street lighting circuit, the circuit shall be fused according to its rating, but shall not use fuses larger than 32 Amps. Fuses are to be housed in a street lighting control point (SLCP) pillar as specified in NS 127. The fuse shall be HRC type.

In the base of each steel lighting pole, a 10A HRC fuse shall be used to protect the luminaire wiring and hardware. The fuse shall be located on an appropriate link panel as per Table 1.

5.1.6.6 Isolation Facilities must be made available through a link or fuse located in the base of the steel lighting pole sufficient for the isolation of the luminaire/s to occur if remedial or maintenance work is required on the luminaires by Ausgrid or its contractors in accordance with the Ausgrid Electrical Safety Rules.

5.1.6.7 Control Streetlights shall normally be controlled by a photoelectric cell (PE cell) integrated into the luminaire. For refurbishment work, a pole mounting NEMA PE cell base is available.

Where a dedicated street lighting circuit is required, the street lights shall have integral photoelectric (PE) cell control and the street lighting cables shall be permanently energised and protected as per clause 5.1.6.5.

If the type of luminaire approved by Ausgrid does not have integral PE cell base and a pole mounted NEMA PE cell base cannot be used, then a single NEMA PE cell shall be installed at the Street Lighting Control Point, to control the street lighting circuit. In this case, the street lighting conductors shall of necessity be de-energised during daylight hours.

In some locations, individual PE cells are ineffective, e.g. CBD areas with high rise buildings, wall mounted lights in underpasses. In these situations, the streetlights shall be controlled by a PE cell that will act as the switching device for a street lighting control point that will include the switching mechanism to energise the street lighting supply. Pole-mounted SLCP enclosures (stockcode 72793) are detailed in Ausgrid drawing A1-19398. Street lights controlled by a circuit PE cell shall include a by-pass switch to facilitate fault finding and other maintenance work.

PE cells should be placed so that they are not interfered with by artificial light sources.

5.1.6.8 Conduits Conduits for low voltage domestic services and street lighting cables shall be in accordance with NS 130. Additionally, the supply cable from the pillar to the pole and between poles shall be run in appropriate 50mm UPVC orange conduit.

The street lighting supply cables shall be mechanically protected where they enter and leave a direct buried steel lighting pole by means of appropriate 50mm UPVC orange conduit bends.

5.1.6.9 Insulated spigots Insulated spigots are required to achieve an additional layer of insulation between the streetlight and the column. These are required on all new installations where a steel column is used.

Street light columns of 6.5m and 7.5m are primarily used for residential road (Category P) installations; the spigot size on these columns has been designed for Category P luminaires which is 34mm. Accordingly, a 34mm ID (inside diameter) to 34mm OD (outside diameter) insulating spigot shall be used on these columns.

For columns greater than 7.5m which are primarily used for category V installations, the spigot size is 42mm to cater for heavier luminaires. A 42mm ID to 42mm OD insulated spigot is to be used on these installations.


Amendment No 3


Table 2 – Insulating Spigots details the insulated spigots that are approved and available for use on Ausgrid’s network.

Insulated spigots are not required for installations on timber poles.

Table 2 – Insulating Spigots

Luminaire Category Description Stock code Photo

Cat V

Side Entry Insulating Spigot 42mm ID to 42mm OD (clamp type)

176441

Cat P

Side Entry (Pole > 7.5m)

Insulating Spigot 42mm ID to 34mm OD (clamp type)

177351

Cat P

Side Entry (Pole <= 7.5m)

Insulating Spigot 34mm ID to 34mm OD (clamp type)

184448

Cat P

Side Entry

Insulating Spigot 42mm ID to 34mm OD (threaded type)

68866

Cat V and P Post Top Insulating Spigot 34mm ID to 76mm OD

68874


Amendment No 3


5.1.6.10 Floodlights for pedestrian lighting To maintain double insulation on floodlights the following insulating brackets shall be used:

Table 3 - Floodlighting Brackets

Description Stock code Photo

44mm diameter floodlighting bracket 72249

72mm diameter floodlighting bracket 72223

5.2 Lighting design

5.2.1 Lighting design brief The Street Lighting Customer is to provide the lighting designer with sufficient information to define the scope of the lighting design. The design brief will state whether Australian Standard compliance is required, and if so will nominate a lighting sub-category.

Refer to AS/NZS 1158 series for sample lighting design briefs.

5.2.2 Qualification of the lighting designer The Lighting Designer shall be qualified by appropriate training and experience to undertake Australian Standard compliant lighting designs.

5.2.3 Australian standard compliance The lighting design is to comply with Australian Standard AS/NZS 1158 unless otherwise specified by the Street Lighting Customer. In the case of pedestrian crossings that will be maintained by Ausgrid, all designs must comply with AS/NZS 1158.4.

The lighting designer shall provide documentation demonstrating compliance with AS/NZS 1158 series to the Street Lighting Customer.

Note: As stated by AS/NZS 1158 series, the lighting designer shall state the maintenance factor used in the lighting design and the basis for calculating that maintenance factor. To enable calculation of the maintenance factor, the brands and part numbers of approved lamps are shown in Annexure C. All approved luminaires in Annexure C have an IP rating of IP6X. Ausgrid has optimised its bulk lamp replacement (BLR) schedules per region depending on the mix of luminaires. This information will be provided to designers so that an appropriate maintenance factor can be calculated.

5.2.4 Street lighting equipment The lighting design shall utilise Ausgrid’s approved street lighting equipment, as shown in Annexure C

5.2.5 Lighting of cul-de-sacs If the luminaire is to be installed at the end of a cul-de-sac, an Aeroscreen, reduced Roadway Reserve Width luminaire or 360 degree glare shield shall be used to minimise obtrusive light.

5.2.6 Placement of steel lighting poles Steel lighting poles should be located in accordance with NS 167 and AS/NZS 1158. It is acknowledged that some older suburbs have very narrow footpaths, which preclude compliance with the setbacks preferred in modern road design.

Where roll kerbs are provided in the subdivision, due consideration shall be given to the road controlling authority’s requirements for the lateral location of street light standards.


Amendment No 3


The spacing of the poles and lights shall be determined by lighting design.

The pole shall be installed vertically with the outreach arm projecting at right angles to the kerb and towards the road’s centre line. This situation does not take precedence over the requirements of special designs.

5.2.7 Rag-bolt mounted steel lighting poles Wherever possible e.g. in greenfield sites, in uncongested footpath, the steel lighting pole shall be the rag-bolt mounted type. Direct buried steel lighting poles are available but their use shall be limited to where rag-bolt mounted poles cannot be installed.

Rag-bolt assemblies should always be installed in accordance with drawing A2-514087 – Standard Construction Street Lighting Column Pile Footing Details. Particular note should be taken of Table 1 on A2-514087 which details the required pile depths for various MH and outreach configurations.

5.2.8 Pedestrian crossing lighting The Designer shall note that the approved floodlights in C.11.3 are the asymmetrical type. Therefore the design shall accurately describe installation parameters to ensure that lights can be installed to the compliant design. In the planning stage, field confirmation of the pole locations may be required to ensure that aim points of the design are accurate. Clause 10.2 contains additional information.

Note: The Australian Standard for pedestrian crossing lighting specifies vertical illuminance values at ground level and at 1.5m above ground. Therefore, in general for a two-way street, two floodlights are needed in total to achieve vertical illuminance values from the two directions of travel. These light technical parameters are meant to allow drivers approaching the pedestrian crossing to clearly see persons using the crossing. The use of floodlights directly above the pedestrian crossing, while providing horizontal illuminance of the crossing, will not comply with the lighting technical parameters because vertical illuminance will not be achieved.

5.2.9 Poles with ‘pole mounted substations’ Refer to NS 122 for restrictions on street lighting equipment near Pole Mounted Substations. In particular, floodlights shall not be installed on poles containing Pole Mounted Substations.

5.2.10 Decorative lighting Ausgrid has a limited range of decorative style street lighting that is available for road lighting in new developments only. Decorative lighting in parks and other public spaces is maintained as a legacy only. Ausgrid will seek to progressively move away from ownership of these assets as installations reach the end of their economic lives or become no longer serviceable. Ausgrid may review its position on decorative lighting in the future, however it will only be considered if cost of installation and maintenance can be adequately recovered from the customer via regulated public lighting charges.

5.2.11 Painting of street lighting furniture Where the Street Lighting Customer requires a coloured steel lighting pole, an Australian Standard colour shall be selected from the range of colours specified in Australian Standard 2700 "Colour Standards for General Purposes". The painting process shall use a two-part polyurethane paint finish applied over the exterior galvanised surface of the steel pole and bracket arm. The surface preparation and the application of the finish coats shall be to the paint manufacturer’s directions.

Powder coat finishes shall NOT be used on steel poles and bracket arms. Powder coat finishes may be used on decorative luminaires. The Customer shall advise Ausgrid of the Australian Standard Colour coding for the paint finish as part of the Asset Information provided at hand over.

Note: All painting or re-painting will be at direct cost to the Street Lighting Customer.

Where it is necessary for Ausgrid to replace a painted steel pole and/or luminaires, the following will apply:

General Steel Lighting Pole: will be replaced with equivalent galvanised but unpainted type.


Amendment No 3


Decorative: will be replaced with the closest matching colour available.

Luminaires: will be replaced with an equivalent luminaire of the nearest colour.

This clause does not obligate Ausgrid to replace pre-2010 non-standard decorative poles, luminaires or colours in a like-for-like fashion.

5.3 Approved street lighting equipment list Street lighting designs must specify equipment approved by this Network Standard. Annexure C lists specific equipment which complies with Ausgrid specifications contained in Annexure B.

5.3.1 Photometric data for luminaires Annexure C details the photometric data (I-tables) associated with approved luminaires. Photometric files can be found on the Street Lighting Assets page in Ausgrid’s internal intranet (Balin) or provided on request. ASP’s can source files from suppliers or manufacturers.

5.4 Design documentation Lighting design documentation shall comply with the relevant parts of AS/NZS 1158 series, and be provided to the Street Lighting Customer.

All electrical design documentation shall comply with NS 104 Specification for Electrical Network Project Design Plans.


Amendment No 3


EQUIPMENT AND PURCHASING 6.0

6.1 Equipment specifications See Annexure B.

6.2 Approved equipment list Approved materials can be found on Ausgrid’s Approved Material List (AML) which is published on Ausgrid’s website. See Annexure C.

6.3 Approval of non-standard equipment The approved street lighting equipment range is periodically reviewed by Ausgrid in consultation with the Street Lighting Customers. Equipment supply tenders are periodically issued and contracts established.

Currently, materials may also be approved using the NS181 Approval of Materials and Equipment and Network Standard Variation process.

6.4 Purchase materials through Ausgrid Stores Accredited Service Providers and Contractors must use only approved products on Ausgrid’s network. The approved range of lighting equipment has been nominated by Ausgrid in consultation with its Street Lighting Customers and alternatives will not be considered.

To purchase materials from Ausgrid, the Project Manager must contact Ausgrid’s Project and Customer Liason officer by email on [email protected]. All materials will be made available for the Customer pick up from:

Somersby Warehouse Lot 11 Kangoo Road Cnr Wella Way Somersby NSW 2250

6.5 Asbestos All materials and equipment used for construction of Ausgrid’s assets are to be free from Asbestos and or Asbestos related products. Suppliers are expected to comply with the Work Health and Safety Act 2017 (NSW) together with the Work Health and Safety Regulation 2017 (NSW) and confirm in writing that all products supplied to Ausgrid contain no Asbestos related materials.

TRANSPORT 7.0

7.1 Transport of poles The lengths and outreach sizes of steel lighting poles have been specified with transport in mind.

7.2 Transport of lamps Lamps shall be transported in individual lamp sleeves and boxes, preferably in original packaging to minimise damage during transport.

7.3 Transport of luminaires New luminaires should be transported in original packaging to minimise damage during transport.


Amendment No 3


INSTALL 8.0

8.1 Construction planning The electrical designer is responsible for providing local authorities and the RMS (as appropriate) with copies of the proposed construction plans at least 40 days before work is to commence, and must give due consideration to any special requirements of these authorities.

This requirement is to ensure that the proposed electrical works comply with the Electricity Supply Act Section 45.

8.2 Installation of steel lighting poles Steel lighting poles must be erected in accordance with the applicable requirements of Network Standard NS 128 Specification for Pole Installation and Removal. In particular, the centre line of installed poles must be vertical, and poles must be stable. Backfilling must be in accordance with NS 128. Burial depths shall be in accordance with AS 1798.

8.2.1 Finished ground levels The construction of the subdivision sometimes involves significant changes in the ground level. Because the electricity supply assets are progressively installed as the subdivision is constructed, it is important that the assets are installed relative to the finished ground levels.

Refer to Network Standard NS 130 for the installation level of rag-bolt assemblies.

8.3 Installation of bracket arms Installation of bracket arms on wood poles shall comply with Work Health and Safety Act 2017 (NSW) with respect to controlling and lifting of loads.

8.4 Installation of pole wiring For safety and reliability reasons, all items of equipment within steel lighting poles which are intended to be attached to supports must be firmly attached so that no item will dislodge and become hazardous, especially when access covers are opened. In particular, Allen keys provided by manufacturers must be removed from inside link covers.

8.5 Labelling of street lighting assets Wood poles and steel lighting poles shall be numbered and labelled in accordance with NS 148.

8.6 Data capture Equipment and repair data must be recorded for all customer requests, ad-hoc repairs, pole replacement, BLR follow up work, night patrol work, minor capital and contestable work. Data must be captured using the Street Lighting Field Data Capture sheet which is available in paper and electronic forms. As an alternative, the MAM system can be used by Ausgrid contractors.

COMMISSION 9.0

9.1 Commissioning checks / tests Prior to commissioning, the following visual checks shall be performed:

Verify that the installation has been installed consistent with the project design.

Verify that the correct insulation system has been constructed, i.e. double insulated.

Verify that the correct wattage and type of luminaire has been installed.

Verify that the luminaire mounting height is as recorded in the field data capture sheet.

Verify that approved street lighting materials have been used for the construction.

Verify that all street lights switch on at dusk and operate correctly. This can be achieved by covering the photoelectric cell, excluding all light.

Where underground cabling is involved, witness final cable testing and/or verify receipt of all cable test results as detailed with NS161.


Amendment No 3


MAINTAIN 10.0

10.1 Luminaire markings including lamp shape Luminaire markings must be in accordance with AS/NZS TS 1158.6. The luminaires are generally marked with coded information on its exterior to facilitate their identification and maintenance. LED luminaires are marked with their total system watts and traditional lamp based technology is marked with the nominal lamp wattage.

For example:

S250 C 09 means sodium 250W, clear (tubular) lamp. The luminaire was manufactured in 2009.

M400 99 means mercury 400W lamp. The luminaire was manufactured in 1999.

S150 D A 07 means sodium 150W, diffused (elliptical) lamp, aeroscreen. The luminaire was manufactured in 2007.

L17 18 means an LED with total 17 total system watts. The luminaire was manufactured in 2018.

Additionally in the Sydney and Central Coast regions, the codes ‘DI’ and ‘SI’ have been specified by Ausgrid for luminaires.

DI means double insulated luminaire

SI means single insulated luminaire, and therefore insulating spigots are required for mounting.

10.2 Pedestrian crossing floodlights Floodlights approved by Ausgrid for pedestrian crossings are the ‘asymmetrical’ type, i.e. the light is ‘thrown forward’. Therefore the maximum intensity of the new floodlight is not perpendicular to the glass visor.

For maintenance situations, i.e. where the floodlights’ heights and distances from the pedestrian crossing are generally not altered, the replacement asymmetrical floodlight should be mounted with glass visor pointing to the centre of the pedestrian crossing area, and then brought back to the vertical approximately 21 degrees, to cater for the ‘forward throw’ angle of the maximum intensity of the floodlight. This guideline should be sufficient to ensure that the maximum intensity of the floodlight is aimed within the pedestrian crossing boundaries for the purpose of maintenance. Where the floodlight as a consequence is not installed with the glass visor flat to the horizontal, an approved glare hood shall be installed to minimise glare and upward waste light.

For new construction which is accompanied by a lighting design, the floodlight will be installed with the glass visor flat on the horizontal. Therefore a glare hood will not be required. Note that to comply with Australian Standard requirements the brightest spot of the newly designed pedestrian crossing may be located outside of the pedestrian crossing boundaries.

10.3 Spot maintenance Spot maintenance personnel shall determine the component which has failed, and replace that component. For LED street lights, the only replaceable component within the luminaire is the PE cell. If this is not the cause of failure then the luminaire should be replaced with the current default luminaire.

All failed LED street lights must be returned to the Somersby store so that warranty claims can be made.

Annexure E lists spare parts available for the maintenance of legacy street lights.

Where a local Council requests Ausgrid to undertake work to address a glare complaint, the Council will be required to pay applicable charges for the work, with the exception when a glare complaint is received within three months of completion of any Ausgrid-driven capital work


Amendment No 3


10.4 Removal of overhead street lighting circuits This clause applies to existing street lights that are connected to a dedicated overhead street lighting circuit, where an overhead low voltage mains circuit is also available.

10.4.1 Incidental work When replacing an existing luminaire, ensure that the new luminaire is;

(a) directly connected to overhead low voltage mains, and

(b) controlled individually by a photoelectric cell.

10.5 Replacement of existing luminaires Luminaires should be replaced in their entirety with the default replacement luminaire under the following circumstances:

Cover needs replacement and is no longer held as a stock item

External control gear whether pole mounted (on timber poles) or panel mounted (in steel columns) fails

Internal control gear fails

Luminaire has required spot maintenance more than 2 times within 6 months

All failed LED street lights must be returned to the Somersby store so that warranty claims can be made.

Category P - Roadway Reserve Width (RRW) > 12m 10.5.1

10.5.1.1 Category P1/P2 Typically this category of lighting is reserved for collector roads and non-arterial roads where the risk of crime is a concern and the level of pedestrian activity is high. Some Councils have decided to light areas with high density housing to this requirement to ensure anti-social behaviour does not occur.

As this category demands a higher level of light, this may require the use of a category V luminaire.

10.5.1.2 Category P3 Existing P3 lighting schemes have been typically serviced by 125W High Pressure Mercury (MBF), 70W High Pressure Sodium (HPS) and more recently in 72W Ceramic Metal Halide (MHI) luminaires. The LED luminaires tabled below replace all of these existing luminaire types.

Table 4 – Category P3 LED luminaires

Luminaire Category Luminaire Description SAP Luminaire Code Stock Code

Category P3 StreetLED MK2 28W 28W LED SY 183949

LRL P3 33W LED 33W LED LRL TBA

Either of the above P3 luminaires can be used to replace existing P3 luminaire types. For new installations where a design is required either luminaire can be chosen that best suits the particular scenario.


Amendment No 3


10.5.1.3 Category P4/P5 Ausgrid currently use LED as its default luminaire type for category P4 and P5. The range of available fittings is tabled below.

Table 5 Category P4/P5 LED luminaires


Category P4/P5 StreetLED MK2 17W 17W LED SY 184102

GE Evolve 17W 17W LED GE 183951

These LEDs should be used to replace all 80W & 50W MBF, Twin 20, 42W CFL, 50W HPS, and any other luminaire type installed on residential roads. Currently Ausgrid is only replacing these types of fittings when they fail or are no longer serviceable. In addition to replacing on failure, Twin 20 luminaires should be replaced when the cover needs to be replaced. Ausgrid has two major replacement capital programs, scheduled to be completed prior to the end of the year 2020, to replace all Twin 20 luminaires and all P4/P5 Mercury Vapour luminaires.

Where an LED is replacing a luminaire on a 0.5m bracket on a road with RRW > 12m, a 2m bracket should be installed (stock code 72421). Luminaires in these situations should ideally be mounted between 6.0m – 6.5m. This can be achieved by mounting the bracket just above any communications installations on the pole.

Along with the luminaires above there are glare shielded visors available for the StreetLED MK2. Stock codes for these items are tabled below. These visors can be used at the discretion of the lighting designer to address glare complaints that have been agreed by local council to rectify.

Table 6 - StreetLED MK2 Visor accessories

Visor type Stock Code

Standard replacement visor 184465

Cut Off visor (Aeroscreen) 184466

Glare shield visor (rear only) 184467

Pathway visor (front and rear) 184468

Glare shield 360 visor 184469

Category P - Roadway Reserve Width (RRW) <= 12m 10.5.2An area of concern when replacing existing street lights with LEDs is the issue of glare. Glare from LED luminaires is caused by intense light sources designed to light the road reserve spilling through windows into residential living spaces. This issue is more prominent in areas where the roadway configuration is significantly different than the standard 20m RRW, i.e. in narrow roads or laneways. To combat this Ausgrid is introducing a reduced roadway reserve width LED streetlight. This is to be used on all category P5 installations where the RRW is 12m or less. The Stock code is 183953. To further minimise obtrusive light it is ideal to install this street light on a 0.5m bracket with 0 degree upcast. Stock code for this bracket is 72322. Existing brackets on roads where this street light is used should be replaced with this bracket.

Table 7 – Category P4/P5 Reduced Roadway Reserve LED luminaire


Category P4/P5 StreetLED MK2 17W reduced RRW 17W LED SY RRW 183953


Amendment No 3


Figure 2 - Reduce Roadway Reserve Width StreetLED

Mounting height in situations where this luminaire is used should be kept as low as possible to a minimum of 5.0m (where the light is installed over a road), however this is dependent on the spacing of the street lights. The table below should be used as a guide to the installation mounting height.

Table 8 Spacing table for reduced RRW luminaire

Maximum Spacing for different Roadway Reserve Widths (m) – Category P5

Mounting Height (MH) (m) – 0 degree upcast Roadway Reserve Width (RRW) (m)

6 8 10 12

5.0 75 71 64 35

5.5 79 76 70 41

6.0 82 80 76 49

6.5 86 84 81 58

7.0 89 88 85 77

7.5 92 91 89 82

As an example, if there are street lights installed on every pole on a street with a 12m RRW it would be possible to install the street light at a mounting height of 5.0m assuming pole spacings of approximately 35m. Where there are lights on every second pole on the same roadway configuration, the streetlight would need to be installed at 7.0m or above to achieve compliance.

Category V 10.5.3Ausgrid’s current default luminaire for replacement of failed category V luminaires are the category V LEDs. These can be used as direct replacements for high wattage mercury luminaires as tabled below. Details of the types of LED luminaires currently approved for use can be found in C.11.1.

Table 9 - Default Category V Replacement

Existing Luminaire Replacement Luminaire

250W mercury vapour (all types) LED equivalent to subcategory V3

400W mercury vapour (all types) LED equivalent to subcategory V1

High Pressure Sodium (HPS), Sylvania Roadster Active Reactor were previously the default replacement and may continue to be used during the transition until stock has diminished. Details of the types of HPS luminaires can be found in C.11.1.


Amendment No 3


REFURBISH 11.0

11.1 Street lighting pole screening kit When live work on steel or concrete lighting poles is required, such work shall be performed in accordance with the Electrical Safety Rules.

The use of the street lighting pole screening kit depicted in Figure 3 is an approved precaution to screen the conductive pole from live conductors. The complete kit is available on the stock code listed in Table 10. This kit should be adjustable for all sizes of pole door openings.

Note that additional screening between live conductors may be required to safely undertake the work.

The user of this kit shall have received training in SS1100 “JOINTERS LIVE LOW VOLTAGE WORK AND SCREENING”.

Figure 3 - Assembled Kit

Table 10 - Screening Kit Contents

Street Lighting Pole Screening Kit Contents Stock Code

1 x Yellow ‘Ripstop’ storage bag

180336

1 x Top & bottom PVC outer pole covers with magnetic fasteners

2 x Large plastic screening inserts

2 x Small plastic screening inserts

1 x Polycarbonate clip with securing flap

1 x Silicon end cap for screening of pole tongue

2 x Velcro straps for storage and use on non metal poles

1 x Insulation ground mat with pole cut out


Amendment No 3


REPLACE 12.0

12.1 Use of frangible poles In accordance with AS/NZS 1158.1.3, where a lighting pole is replaced due to damage or age, a rigid lighting pole should be placed at the stated setback from the kerb. Ausgrid has not approved the ongoing use of frangible steel lighting columns (slip base or energy absorbing). This will be Ausgrid’s position until a product is designed, manufactured and tested in accordance with a suitable standard.

RECORDKEEPING 13.0

The table below identifies the types of records relating to the process, their storage location and retention period.

Table 11 - Recordkeeping

Type of Record Storage Location Retention Period*

Approved copy of the network standard

BMS Network sub process Standard – Company

Unlimited

Draft Copies of the network standard during amendment/creation

HPRM Work Folder for Network Standards (HPRM ref. 2014/21250/214)

Unlimited

Working documents (emails, memos, impact assessment reports, etc.)

HPRM Work Folder for Network Standards (HPRM ref. 2014/21250/214)

Unlimited

* The following retention periods are subject to change eg if the records are required for legal matters or legislative changes. Before disposal, retention periods should be checked and authorised by the Records Manager.

AUTHORITIES AND RESPONSIBILITIES 14.0

For this network standard the authorities and responsibilities of Ausgrid employees and managers in relation to content, management and document control of this network standard can be obtained from the Company Procedure (Network) – Production/Review of Network Standards. The responsibilities of persons for the design or construction work detailed in this network standard are identified throughout this standard in the context of the requirements to which they apply.

DOCUMENT CONTROL 15.0

Content Coordinator : Manager - Street Lighting Engineering

Distribution Coordinator : Senior Engineer – Guidelines, Policies and Standards


Amendment No 3


Annexure A Privately Owned Street Lights

A.1 Not installed on Ausgrid assets Where the Public Lighting Customer decides to assume complete responsibility for their street lighting installation, Ausgrid’s only requirements are that the installation conforms to:

Australian Standard AS/NZS 3000; and

NSW Service and Installation Rules.

Note: Examples of private street lighting installations are Community Title Developments or schemes which do not comply with this Network Standard.

A.2 Recording of connections to the Ausgrid network All private lighting installations are to be shown in the GIS as connection points only. Refer to Network Standard NS 100.

.


Amendment No 3


Annexure B Equipment Specifications

B.1 Warning Specifications contain equipment that is used to construct new street lighting assets as well as to maintain older style assets.

Although specifications are reviewed regularly, the equipment listing and stockcode information shall not be read as currently approved.

B.2 Specification for steel lighting poles, bracket arms and rag bolt assemblies Due to the size of the specification, it is available on request from Ausgrid.

B.3 Specification for street lighting equipment (luminaires, lamps and control gear) Due to the size of the specification, it is available on request from Ausgrid.


Amendment No 3


Annexure C Approved Equipment List

C.1 Wood poles See NS 128 for a listing of wood poles available.

C.2 Steel lighting poles

C.2.1 Post top poles Table C1 - Post Top Poles

Stock code

Pole Mounting Height Outreach Mounting Method

Pole Drawing No.

Panel Size

Link Panel Stockcode

Spigot Size DI Spigot Stockcode

90001 4.5m Rocks - In-Ground mounted B1-63060 125mm x 610mm 150797 34mm 68874

72082 4.5m Rocks - Base Plate mounted B1-63060 125mm x 610mm 150797 34mm 68874

72017 4.5m Post Top Continuous tapered - In-Ground mounted B1-66271 125mm x 420mm 66845 34mm 68874

72033 7m Post Top Continuous tapered - In-Ground mounted B1-66271 125mm x 610mm 150797 34mm 68874

72025 8.5m Post Top Continuous tapered - In-Ground mounted B1-66271 125mm x 610mm 150797 34mm 68874

89953 10.5m Post Top Reduced tapered - In-Ground mounted B1-66271 125mm x 610mm 150797 34mm 68874


Amendment No 3


C.2.2 Poles with curved outreach arms Standard steel columns with curved bracket arms, either base plate or in-ground mounted, range in mounting height (MH) size from 6.5m – 12.0m. Outreach arms range from 2.0m – 6. 0m. Drawing numbers B1-66272, B1-66273, B1-66637 and B1-115041 detail Ausgrid’s available columns.

Columns with a 6.5m and 7.5m MH are constructed with a 34mm spigot size. Columns greater than 7.5m MH are constructed with a 42mm spigot. 34mm spigots are to accommodate residential road (Category P) luminaires and 42mm spigots are for major road luminaires (Category V). Spigot adaptors are available if a larger mounting height is required for category P installations.

If a 3.0m outreach is required for columns 9.0m and above, a 1m extension arm should be used on a 2.0m outreach. Stock code for this extension arm is 79962 and drawing number A2-65411. 6.5m and 7.5m columns have separate stock codes for 3.0m outreach constructions.

Table C2 - Poles with Curved Outreach Arms

COLUMNS WITH CURVED OUTREACH ARMS (STANDARDS)

Stock Code Mounting Height Outreach Arm Spigot Size Mounting Drawing

71993 6.5m 1x2.0m 34mm In-Ground Mounted B1-66272

100115 6.5m 1x2.0m 34mm Base Plate Mounted B1-66273














Amendment No 3



























Amendment No 3


C.3 Bracket arms Table C3 - Bracket Arms for Wood Poles

Stock Code Description Type Spigot Size (OD) Drawing Upcast angle

72348 500 mm arm projection - 34mm A2-48728 5 deg

72330 500 mm arm projection, wall mounted - 34mm A2-32329 5 deg

72322 500 mm arm projection, horizontal mounted - 34mm A2-62405 0 deg

72421 2m arm projection - 34mm A1-32330 5 deg

72447 3.5 m arm projection - 34mm A1-46911 5 deg

72397 4 m arm projection - 34mm A1-36355 5 deg

72280 2 m arm projection Type 1 42mm A1-23227 5 deg

72264 3 m arm projection Type 2A 42mm B1-58188 5 deg

H65938 3 m arm projection Type C 42mm A2-515156 5 deg

72272 4.5 m arm projection Type 3A 42mm B1-59737 5 deg

723141 6 m arm projection Type 6 42mm B1-63736 5 deg

72256 4 metre arm projection, 4 metre uplift Type 7 42mm B1-66439 5 deg

72439 Pedestrian crossing luminaire bracket arm - 42mm 29188 0 deg

Table C4 – Post Top Conversion Brackets

Stock Code Description Type Spigot Size (OD) Drawing Upcast angle

H106450 Post Top Conversion outreach approx. 1.1 m - 34mm A2-519502 5 deg

Non-stock item Post Top Conversion short outreach 250 mm - 34mm A2-231819 0 deg

1 Bracket is not to be used on timber poles less than 200mm diameter at the point of connection


Amendment No 3


C.4 Prestigious lighting system Table C5 - Prestigious Lighting System

Stock Code Description Drawing

H120469 PLS 1 Street Lighting 4.5 m Pole, specify colour A2-565780

179692 PLS 1 Street Lighting 4.5 m Pole, Colour = G12 Holly A2-565780

179693 PLS 1 Street Lighting 4.5 m Pole, Colour = N61 Black A2-565780

179691 PLS 1 Street Lighting 4.5 m Pole, Colour = R55 Claret A2-565780

H120477 PLS 8 Outreach Arm - Single Hook Arm, specify colour A2-520427

179679 PLS 8 Outreach Arm - Single Hook Arm, Colour = G12 Holly A2-520427

179680 PLS 8 Outreach Arm - Single Hook Arm, Colour = N61 Black A2-520427

179678 PLS 8 Outreach Arm - Single Hook Arm, Colour = R55 Claret A2-520427

H120691 PLS 9 Outreach Arm - Double Hook Arm, specify colour A2-565306

H125237 PLS 10 Outreach Arm - Curve Fancy Straight Out Arm, specify colour A2-520430

179676 PLS 10 Outreach Arm - Curve Fancy Straight Out Arm, Colour = G12 Holly A2-520430

179677 PLS 10 Outreach Arm - Curve Fancy Straight Out Arm, Colour = N61 Black A2-520430

179675 PLS 10 Outreach Arm - Curve Fancy Straight Out Arm, Colour = R55 Claret A2-520430

H120683 PLS 16 Spigot Adaptor, specify colour A3-520422

C.5 Rag bolt assemblies Table C6 - Rag Bolt Assemblies

Stock Code Description PCD Length Drawing

H5880 Rag Bolt Assembly 350 1400mm A2-514607


Amendment No 3


C.6 Outreach extension arm Table C7 - Outreach Extension Arm


79962 1 metre outreach arm extension for use on pole with 1.5m or 2m outreach arm A2-65411

C.7 Insulating spigots Table C8 - Insulating Spigots

Stock Code Description Drawing Number Notes

176441 42mm - 42mm A2-125149 Use for side entry Category V luminaires on steel standards 9.0m and above

177351 42mm - 34mm A2-151959 Use for side entry Category P luminaires on steel standards 9.0m and above

184448 34mm - 34mm A2-240795 Use for side entry Category P luminaires on steel standards 7.5m and below

68874 Post top A3-43238 Use for post top luminaires

C.8 Other insulating brackets Table C9 - Other Insulating Brackets


72249 44mm diameter floodlighting bracket A2-62980

72223 72mm diameter floodlighting bracket A2-62980


Amendment No 3


C.9 Non-insulating spigots Table C10 - Non-insulating spigots


132258 Angled Spigot 42mm ID to 42mm ID (tube) A2-117697

H77149 Spigot 42mm ID to 34mm OD A3-514011

C.10 Steel pole link panels Table C11 - Link Panels

Stock Code Description Drawing Number Pre Wired Notes

66845 Small link panel with single fuse A1-62525 No Panel to be used on standards 6.5m or less with single streetlight

183985 Large link panel with single fuse A1-62525 No Panel to be used on standards 7.5m or greater with single streetlight. Best used where SL circuit loops in and out at panel

183986 Large link panel with double fuse A1-62525 No Panel to be used on standard columns 7.5m or greater with dual streetlights.

150797 Large link panel with single fuse A1-228838 Yes Panel to be used on standard columns 7.5m or greater with single streetlight. Best used when directly connected to a pillar and no looping is required


Amendment No 3


C.11 Luminaires

C.11.1 Cat V road lighting luminaires All category V Luminaires have a NEMA PE cell base. PE Cell and lamp to be ordered separately.

Table C12 - Cat V Road Lighting Luminaires

Stock Code Description To suit pole

spigot Manufacturer Model

Manufacturers Part No.

I table Design Lumens

Notes Stock Code of

lamp used

177243 100W HPS Luminaire 42mm SYLVANIA Roadster PR47K01 98358 9000 182081

182516 400W HPS Active Reactor Luminaire

42mm SYLVANIA Roadster PRE44K01L 98382 48000 182068

179811 100W HPS Luminaire Aeroscreen

42mm SYLVANIA Roadster PR47K31 98385 9000 12328

182678 400W HPS Active Reactor Luminaire, Aeroscreen

42mm SYLVANIA Roadster PR44K03 PRE44K10L 48000 182068

184463 100W LED V3

T3 Distribution

42mm Aldridge Traffic Systems

VLED V162100WT3N7PBPAG

DP161220-01EM

13353 N/A

184464 200W LED V1

T3 Distribution

42mm Aldridge Traffic Systems

VLED V162200WT3N7PBPAG

DP161220-01AM

23841 N/A


Amendment No 3


C.11.2 Cat P road lighting luminaires All category P luminaires have a NEMA PE cell base. PE Cell to be ordered separately.

Table C13 - Cat P Road Lighting Luminaires

Stock Code Description To suit pole

spigot Manufacturer Model

Manufacturers Part No.


183949 Cat P3 LED 34mm

Gerard StreetLED MK2 28/31W JLB99K15L31 215347M 3600

TBA LRL LRL P3 33W LED TBA TBA TBA

184102 Cat P4/P5 LED 34mm

Gerard StreetLED MK2 14/17W JLB99K05L17 216025 2147

183951 GE Evolve 17W ERRA17P40VSG44 HR-LED2018020601-A 2300

183952 Cat P4/P5 LED Aeroscreen

34mm Gerard StreetLED MK2 14/17W JLB99K15L17 206026 2068

183953 Cat P4/P5 LED Reduced RRW1

34mm Gerard StreetLED MK2 14/17W Reduced RRW

JLB99K25L17 216156 1309

1 This luminaire has been designed for roadways that have an RRW of 12m or less. Compliance to relevant light technical parameters should be checked before use.


Amendment No 3


C.11.3 Pedestrian floodlights All floodlights have a NEMA PE cell base. PE Cell and lamp to be ordered separately.

Table C14 - Pedestrian Floodlights

Stock Code Description Manufacturer Model Manufacturers Part No.


Stock Code of lamp used

181741 150 W, SON-T, narrow beam (low glare) floodlight with 1.5m tail.

SYLVANIA Sylflood Asymmetrical XS42K01 TBA 15000 182070

57752 250 W, SON-T, narrow beam (low glare) floodlight with 1.5m tail.

SYLVANIA Sylflood Asymmetrical XS43K01 202115 28000 182069

57513 400 W, SON-T, narrow beam (low glare) floodlight. SYLVANIA Sylflood Asymmetrical XS44K01 202118 48000 182068

C.11.4 Other decorative style luminaires Table C15 - Other Decorative Style Luminaires

Stock Code Description To Suit Spigot Manufacturer Model Manufacturer’s Part No.

H120451 42W CFL top entry decorative, G12 Holly AS 1158 top entry fixing Interlux Bourke Hill style B7166.78

176769 42W CFL top entry decorative, N61 Black AS 1158 top entry fixing Interlux Bourke Hill style B7166.78

178153 42W CFL top entry decorative, R55 Claret AS 1158 top entry fixing Interlux Bourke Hill style B7166.78

176772 42W CFL top entry decorative, colour to be specified AS 1158 top entry fixing Interlux Bourke Hill style B7166.78

179582 24W LED top entry decorative, colour to be specified AS 1158 top entry fixing 3S Lighting Bourke Hill style 407667

185131 24W LED top entry decorative, G12 Holly AS 1158 top entry fixing 3S Lighting Bourke Hill style 407667

185132 24W LED top entry decorative, N61 Black AS 1158 top entry fixing 3S Lighting Bourke Hill style 407667

185133 24W LED top entry decorative, R55 Claret AS 1158 top entry fixing 3S Lighting Bourke Hill style 407667

H120436 42W CFL post top, colour to be specified 76mm Artcraft Flinders Encounter


Amendment No 3


185138 42W CFL post top, G12 Holly 76mm Artcraft Flinders Encounter

185139 42W CFL post top, N61 Black 76mm Artcraft Flinders Encounter

185140 42W CFL post top, R55 Claret 76mm Artcraft Flinders Encounter

C.11.5 Luminaire special visors Table C16 - Luminaire Special Visors

Stock Code Description Photo

90266 Acrylic Glare shield Visor for Sylvania Roadster Luminaire


Amendment No 3


179214 Pathway Acrylic Visor for Sylvania Suburban / Suburban-Eco Luminaire

184466 StreetLED MK2 Cut Off Visor (Aeroscreen)

184467 StreetLED MK2 rear glare shielded visor


Amendment No 3


184468 StreetLED MK2 Pathway visor (front and rear shield)

183892 StreetLED MK1 Pathway visor (front and rear shield)

184469 StreetLED MK2 360 degree glare shield

183891 StreetLED MK1 360 degree glare shield


Amendment No 3


C.12 Lamps Table C17 - High Pressure Sodium Lamps

Stock Code Wattage Cap Type Lamp Type Special Note Manufacturer Manufacturer's Part Number

Initial Lumens

12161 50 W high pressure sodium

E 27 SON-E with internal igniter

150524 70W high pressure sodium

E 27 SON-T without igniter, to suit Sylvania’s ‘Multikat’ floodlight. SHP-T70/CL/E or equivalent.


E 27 SON-E with internal igniter. Lamp length must be 156mm or less.

Philips SON 70W I 5600


E 40 SON-T - SON-T PLUS 100W GES 9000


E 40 SON-E - Philips SON 150W E 14500


E 40 SON-T - Philips MASTER SON-T PIA Plus 150W/220 E40 1SL

15000

H118521 150 W high pressure sodium

E 40 SON-T double arc tube standby lamp Osram NAV T150W/TT 14000


E 40 SON-E - Philips SON 250W E 27000


E 40 SON-T - Philips MASTER SON-T PIA Hg-Free 250W/221 E40 SLV

28000


E 40 SON-E - Philips SON 400W 48000


E 40 SON-T - Philips MASTER SON-T APIA Plus Xtra 400W E40

48000


E 40 SON-T - Philips SON-T 1000W 130000


Amendment No 3


Table C18 - High Pressure Mercury Lamps

Stock Code Wattage Cap Type Lamp Type Special Note Manufacturer Manufacturer's part number

Initial lumens

182091 50 W high pressure mercury

E 27 MBF/U Osram HQL 50W 4Y 2000


E 27 MBF/U - Osram HQL 80W 4Y 4000


E 27 MBF/U - Osram HQL 125W 4Y 6800


E 40 MBF/U - Sylvania HSL-BW125/E40 6300


E 40 MBF/U


E 40 MBF/U

11940 1000W high pressure mercury

E 40 MBF/U slim type 350mm long x 165mm diameter


Amendment No 3


Table C19 - Metal halide Lamps

Stock Code Wattage Cap Type Lamp Type

176203 70 W metal halide coated ovoid lamp, for universal burning. Colour temperature 3000K.

Part number OSRAM HQI-E70W/WDL or similar.

E 27 HPI-E

176204 100 W metal halide coated ovoid lamp, for universal burning. Colour temperature 3000K.

Part number OSRAM HQI-E100W/WDL or similar.

E 27 HPI-E

146191 250 W metal halide tubular lamp, for horizontal burning.

Part number PHILIPS HPI PLUS 250W GES or similar.

E 40 HPI-T

12336 400 W metal halide tubular lamp, for horizontal burning, lamp voltage 120 / 125V. E 40 HPI-T

175522 400 W metal halide coated ovoid lamp, for universal burning, and for use with constant wattage control gear. Part number M400/C/U or similar.

E 40 HPI-E

180341 1000 W metal halide tubular lamp, for horizontal burning. To fit in Philips HNF901 Puma floodlight. E 40 HPI-T

Table C20- Ceramic Metal Halide Lamps

Stock Code Wattage Cap Type Lamp Type Special Note Manufacturer Manufacturer's part number

Initial lumens

182483 72 W Ceramic metal halide E27 CMI Sylvania CMI70W/HOR 7700


Amendment No 3


Table C21 - Fluorescent lamps

Stock Code Wattage Length Colour Temp

Special Note

Manufacturer

Manufacturer's part number

Initial lumens

180174 42W, 4 pin, GX24q-4 cap, CFL compact fluorescent amalgam lamp, colour rendering index 84.

Part number Sylvania LYNX-CFTE-42W/840, or similar.

149 mm 4000K - Osram Dulux T/E 42W/840

3200

11981 18W or 20W, 250V Bi-pin, hot cathode tubular fluorescent lamp

600 mm 4300K

12005 36 W or 40 W, 250V, Bi-pin, hot cathode tubular fluorescent lamp

1200 mm 4300K

12013 65/80W, 250V, Bi-pin, MCFE rapid start, hot cathode tubular fluorescent lamp

1500 mm 4300K

12021 26W CFL 2700K

180321 14W, Bi-pin, G5 cap, hot cathode tubular fluorescent lamp, colour rendering index 84.

Part Number Osram FH 14W/840 Lumilux, or similar.

563 mm 4000K


Amendment No 3


C.13 Photo-electric cells Table C22 - Photo-electric cells

Stock Code Description

182715 10 Amp nominal, NEMA twist-lock socket-type photoelectric control switch.

150425 3 Amp nominal, D2 type photoelectric control switch.

176581 Blanking Cap for NEMA photoelectric switch base. For use with luminaires on switched street lighting circuit.

74922 Base for NEMA twist-lock socket-type photoelectric control switch complete with mounting bracket.

C.14 Miscellaneous Table C23 - Miscellaneous


177501 Three-way street lighting terminal block 16 – 50mm2 copper to 2.5mm2 copper

72793 Pole-mounted SLCP enclosure, drawing A1-19398

177552 10A in-line fuse for use in LV pillar

180336 Street lighting pole screening kit


Amendment No 3


Annexure D Other reference construction

D.1 Prestigious lighting system

Figure D1 - Prestigious Lighting System


Amendment No 3


D.2 Underground Residential Distribution (URD) street lighting options Table D1 - URD Street Lighting Options

Component Description Stock Code

Style No.2 Style No.3 Style No.4 Style No.5 Style No.6 Style No.7

17W LED

70W HPS

42W CFL

24W LED

42W CFL

24W LED

80W MV

70W HPS

42W CFL

70W HPS

42W CFL

24W LED

Columns & Outreach Arms

Column – 6.5m x 2.0m Curved & Ragbolt; Not Painted 100115 Yes Yes

Column 4.5m Ragbolt & Painted, Colour = G12 Holly 179692

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Column 4.5m Ragbolt & Painted, Colour = N61 Black 179693

Column 4.5m Ragbolt & Painted, Colour = R55 Claret 179691 Column 4.5m Ragbolt & Painted, Colour = Other than Holly or Black or Claret, (Specify the colour)

H120469

Hook Arm, Painted, Colour = G12 Holly 179679

Yes Yes

Hook Arm, Painted, Colour = N61 Black 179680

Hook Arm, Painted, Colour = R55 Claret 179678 Hook Arm, Painted, Colour = Other than Holly or Black or Claret, (Specify the colour)

H120477

Double Hook Arm, Painted (Specify the colour) H120691 Yes Yes

Curve Fancy Straight Out Arm, Painted, Colour = G12 Holly 179676

Yes Yes

Curve Fancy Straight Out Arm, Painted, Colour = N61 Black 179677

Curve Fancy Straight Out Arm, Painted, Colour = R55 Claret 179675 Curve Fancy Straight Out Arm, Painted, Colour = Other than Holly or Black or Claret, (Specify the colour)

H125237

Spigot Adaptor, Painted (Specify the colour) H120683 Yes Yes Yes Yes

Ragbolt Assembly H5880 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes


Amendment No 3


Component Description Stock Code

Style No.2 Style No.3 Style No.4 Style No.5 Style No.6 Style No.7

17W LED

70W HPS

42W CFL

24W LED

42W CFL

24W LED

80W MV

70W HPS

42W CFL

70W HPS

42W CFL

24W LED

Luminaires

17W LED - Basic Type Not Painted (Default luminaire) 184102 Yes

70W HPS - Basic Type Not Painted 58289 Yes

42W CFL - Top entry – Painted, Colour = G12 Holly H120451

Yes

Yes

Yes

42W CFL - Top entry – Painted, Colour = N61 Black 176769

42W CFL - Top entry – Painted, Colour = R55 Claret 178153 42W CFL - Top entry – Painted, Colour = Other than Holly or Black or Claret, (Specify the colour)

176772

–24W LED Top Entry Yes Yes Yes

80W MV - Side entry – Painted (Specify the Colour) includes gooseneck bracket

176111 Yes

70W HPS - Side entry - Painted Yes

42W CFL - PostTop - Painted H120436 Yes

70W HPS - PostTop - Painted 57471 Yes

Photoelectric Cell 150425 Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes


Amendment No 3


Annexure E Spare Parts for Maintenance of Legacy Street Lights

E.1 Steel lighting poles Table E1 - Post Top Poles

Stock Code

Pole Mounting Height Outreach Mounting Method Pole Drawing

No. Panel Size

Link Panel Stockcode

Spigot Size

DI Spigot Stockcode

79921 3m Macquarie - In-Ground mounted B1-116157 100mm x 651mm 66852 76mm not available

79913 3m Macquarie - Base Plate mounted B1-116157 100mm x 651mm 66852 76mm not available

72041 3m Post Top Continuous tapered

- In-Ground mounted B1-66271 none available none available 34mm 68874

E.2 Strengthening sleeve Table E2 - Strengthening sleeve


H114348 Strengthening sleeve for steel poles A3-520510

E.3 Insulating spigots Table E3 - Insulating spigots


68866 Insulated Spigot 42mm ID to 34mm OD (threaded type) For use on older style poles and pillar standards only

A3-41826


Amendment No 3


E.4 Legacy luminaires Table E4- Legacy luminaires


179702 250W HPS luminaire; colour = black

179703 150W HPS luminaire; colour = black

181901 80W MV Toorak or similar luminaire with D2 pe cell base, top entry mounting as per AS/NZS 1158.2.1 Painted G12 Holly Green.

181902 80W MV Toorak or similar luminaire with D2 pe cell base, side entry mounting. Painted G12 Holly Green.

176111 80W MV decorative, colour to be specified (gooseneck bracket supplied with luminaire)

185134 80W MV decorative, G12 Holly

185135 80W MV decorative, N61 Black

185136 80W MV decorative, R55 Claret

58289 70W HPS luminaire- Basic Type Not Painted

57455 Carousel 125W MBF post top luminaire

57471 Carousel 70W HPS post top luminaire

58222 Rocks non-integral luminaire E40 lamp base

90217 Parkway non-integral luminaire E40 lamp base

E.5 Luminaire spare parts Table E5 - Philips lighting spare parts

Stock Code Description Part Number

147264 Shade for Philips HNF901 medium beam floodlight. HNF901Hood1


Amendment No 3


Table E6 - GEC lighting spare parts

Stock Code Description Part Number Photo

65649 Slip on visor gasket to suit GEC Optispec luminaire OPCGAS

69369 Visor with hinges to suit GEC Optispan luminaire OPNAB

176142 Visor with hinges to suit 400W GEC Optispan luminaire OPNAB 400

179742 Diffuser clip for Optispan luminaire OPNDIF CLIP

99853 Visor to suit GEC Optipsec luminaire OPCAB

69187 Visor to suit GEC Optispec luminaire, high temperature for 700W

OPCHTAB

Table E7 - Sylvania lighting spare parts

Stock Code Description Part Number Photo

175251 Acrylic Visor for Sylvania Urban series luminaire J00000

H7303 Visor to suit Sylvania M.T.H. series mercury vapour luminaire L00000

69211 Acrylic Visor for 150W/250W B3000 series Sylvania street light luminaire

P00000

69229 Acrylic Visor for 400W Sylvania B2229 series luminaire T00000

179165 Acrylic Visor for Sylvania Suburban luminaires JS00000

69294 Flat acrylic visor for Sylvania B2229 series luminaire


Amendment No 3


180072 Wire guard kit for Suburban luminaire

179741 Kit of 3 cocky clips for Suburban luminaire PR00010


Amendment No 3


Table E8 - Decorative luminaire spare parts

Stock Code Description Part Number

58842 ‘Rocks’ prismasphere refractor for new style luminaire, large hole Compulite CPS 450

100099 ‘Rocks’ prismasphere refractor for old style luminaire, 185mm hole to suit old style caribe fitter Compulite CPS450-185

175022 'Rocks' prismasphere refractor complete with locking ring. New style caribe fitter Compulite CPS450-LR

175023 Rocks' sphere conversion ring to fit CPS-450 to old style caribe fitter Compulite CPS-CON

69120 Sylvania Macquarie sphere, without base casting, lampholder and lower reflector. CF00010

145987 Visor for Sylvania Hyde Park Pearl Ball luminaire Z52174

H6218 Diffuser for GEC Parkway Post top luminaire

H7167 Prismatic Glass diffuser to suit Sylvania twin door B2227 Luminaire

69237 460mm Frosted Sphere cover for 26W PLC Post top luminaire

175381 Diffuser visor for GEC Boston 1 and Boston 2

H103580 Acrylic diffuser cover to suit Bathurst post top lantern GEC BATAD

177185 Visor and black shade assembly for Zumtobel Bega 9484 Olympic Village luminaire 99484.77

NS119 Public Lighting Design and Construction Amendment No 3


E.6 Chokes, boxes and panels Table E9 - Mercury chokes


99838 125W Encapsulated Mercury Vapour Ballast




Table E10 - Mercury choke panels

Stock Code Description Panel size Drawing

66746 125W mercury vapour control panel for 4.5 & 6.5m steel lighting poles

125mm x 420mm A1- 119084

66795 125W mercury vapour control panel 125mm x 610mm A1- 24969





Table E11 - Sodium chokes


58941 70 W Encapsulated high pressure sodium ballast with two terminals, suitable for operation with internal igniter lamp

59048 250 W Encapsulated high pressure sodium ballast

59022 400 W Encapsulated high pressure sodium ballast

H121608 600 W (415 V) Encapsulated high pressure sodium ballast

Table E12 - Sodium choke panels


89995 100 W High pressure sodium control panel 125mm x 610mm A1- 56312






Table E13 - Metal halide choke panels


66860 70W Metal Halide control panel 100mm x 650mm A1- 116183

Table E14 - Metal halide choke boxes


146209 250 W Metal Halide control box A1- 66145



Table E15 - Other choke panels


77909 650 mm x 100 mm x 12 mm Blank panel



Table E16 - Fluorescent chokes


59196 18/20 W 240V 50 Hz Low loss Switch start ballast for use in fluorescent street lighting luminaire, with 8kV impulse withstand.

H5898 Single 20 W 240V Switch start fluorescent ballast.

H5903 40 W 240V Fluorescent Switch start ballast with 457mm leads.

Table E17 - Fluorescent starters


58867 Interchangeable glow-starters for use with 18 W lamps, for both parallel and series 2 x 18 W circuits.

58909 Interchangeable glow-starters for use with 36 W lamps.



Annexure F List of Ausgrid Drawings

Table F1 – Drawing List

Ausgrid Drawing Number

Title

Control and link panels

19398 Pole mounted street lighting control panel general assembly

62525 Street lighting lamp supply panel. panel layout

228838 Link panel for street lighting standards

Poles

63060 Street lighting modified Rocks style lighting columns (in‐ground & BPM) limiting dimensions

66271 Street lighting steel post top columns in‐ground mounted limiting dimensions

66272 Street lighting steel curved bracket arm standards in‐ground mounted limiting dimensions

66273 Street lighting steel curved bracket arm standards baseplate mounted limiting dimensions

66637 Street lighting steel standards with 4.5 or 6m outreach arm in‐ground mounted limiting dimensions

115041 Street lighting steel standards with 4.5 or 6m outreach arm base plate mounted limiting dimensions

514087 Standard construction street lighting column pile footing details

514607 Street lighting ragbolt assembly for steel light standards arrangement and details

520427 Street lighting outreach arm single hook arm arrangement and details

520430 Street lighting outreach arm curve fancy straight out arm arrangement and details

565306 Street lighting outreach arm double hook arm arrangement and details

565780 Street lighting 4.5m pole arrangement and details

Brackets

23227 Street lighting 2m outreach elevated pole mounted bracket type 1 arrangement & details

29188 Street lighting floodlight bracket mounted arrangement & details

32329 Street lighting 0.5m outreach wall mounted bracket arrangement & details

32330 Street lighting 2m outreach pole mounted bracket arrangement and details

36355 Street lighting 4m outreach pole mounted bracket arrangement and details

46911 Street lighting 3.5m outreach pole mounted bracket arrangement and details

48728 Street lighitng 0.5m outreach pole mounted bracket arrangement and details

58188 Street lighting 3m outreach elevated pole mounted bracket type 2A arrangement and details

59737 Street lighting 4.5m outreach elevated pole mounted bracket type 3A arrangement and details

62405 Street lighting 0.5m outreach 0 degree upcast pole mounted bracket arrangement and details

62980 Street lighting floodlight luminare mounting bracket arrangement and details

63736 Street lighting. 6m outreach elevated pole mounted bracket type 6 arrangement and details

65411 Street lighting. 1 metre outreach extension arrangement and details

66251 Street lighting range of pole and wall mounted street lighting brackets



66439 Street lighting 4m outreach elevated pole mounted bracket type 7 arrangement details

231819 Street lighting post top to short outreach conversion bracket

515156 Street lighting pole mounted bracket 3.25m outreach x 0.84m uplift DN 32 spigot arangement and details

519502 Street lighting steel post top to outreach conversion bracket arrangement and details

Spigots

43238 Post top lantern insulated spigot for 3m 4.5m 7m and 8.5m street lighting columns arrangement and details

117697 Street lighting DN 32 to DN 32 angled adapter details

125149 Insulated spigot for V category lantern street lighting column arrangement and details

151959 Street lighting Insulated spigot clamp type for street lighting columns arrangement and detail

240795 Street lighting 3.7mm insulated spigot clamp type for street lighting columns arrangement and details

514011 Street lighting adaptor spigot DN 32 to DN 25 clamp type arrangement and details

520422 Street lighting luminaire fixing spigot nominal size DN65 arrangement and details

Legacy drawings for maintenance

24969 Mercury vapour lamp choke panels for street lighting standards

41826 Street lighing insulated spigot threaded type for street lighting column arrangement and details

56312 H.P.S. lamp choke panels for street lighting standards

66145 Street lighting equipment F.M. and H.P.S. lamps aluminium alloy choke box details

116157 Street lighting 3m Macquarie St type post top columns limiting dimensions

116183 70W metal halide street lighting control panel public works type

119084 125 watt mercury vapour lamp panels for 4.5 & 6.5m street lighting standards general arrangement & details



Annexure G Sample Compliance Check Sheet

Network Standard - Ausgrid · NS119 Public Lighting Design and Construction Amendment No 3...

Documents

Transcript of Network Standard - Ausgrid · NS119 Public Lighting Design and Construction Amendment No 3...