NARROW WEB PRINTING INKS - Nazdar · Nazdar Narrow Web Catalog Flexo - UV LED Inks ... Shawnee’s...
Transcript of NARROW WEB PRINTING INKS - Nazdar · Nazdar Narrow Web Catalog Flexo - UV LED Inks ... Shawnee’s...
Mexico Phone: +52 (55) 4777 1900
e-mail [email protected] today
Nazdar Ink Technologies -World Headquarters8501 Hedge Lane TerraceShawnee, KS 66227-3290 USAToll Free US: 866-340-3579Tel: +1 913-422-1888 E-mail: [email protected] Support E-mail: [email protected]
Nazdar – EMEANazdar House, Battersea RoadHeaton Mersey Industrial EstateStockport, Chesire SK4 3EA United KingdomTel: + 44 (0)-161-442-2111EMEA Technical Service E-mail: [email protected]
Nazdar – Asia Pacific11, Changi North Street 1 #03-03/04Singapore 498823Tel: +65-63854611E-mail: [email protected]
Nazdar – TlalnepantlaGustavo Baz 180 D-4San Jeronimo Tepetlacalco Tlalnepantla, Edo. de Mexico 54090 Mexico Tel: +52 (55) 4777 1900Fax: +52 (55) 5362 7282
Nazdar.com
NARROW WEB PRINTING INKS
Nazdar.com
Distributor:
LIT0700 0519
Got ink questionsWe have ink answers.
An Ink That’s Right For Every Job.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
© 2019 Nazdar
Nazdar Ink Technologies World Headquarters8501 Hedge Lane TerraceShawnee, KS 66227-3290 USAToll Free US: 800-767-9942Tel: +1 913-422-1888 Customer Service E-mail: [email protected] Support E-mail: [email protected]
Nazdar – EMEABattersea Road, Heaton MerseyStockport, England SK4 3EA Tel: + 44 (0)-161-442-2111
Nazdar – TlalnepantlaGustavo Baz 180 D-4San Jeronimo Tepetlacalco Tlalnepantla, Edo. de Mexico 54090 Mexico Tel: +52 (55) 4777 1900Fax: +52 (55) 5362 7282
Nazdar – Asia Pacific11, Changi North Street 1 #03-03/04Singapore 498823Tel: +65-63854611E-mail: [email protected]
Table of ContentsNazdar Narrow Web Catalog
Flexo - UV LED Inks .............................................................................................. 6Rotary Screen- UV LED Inks ............................................................................. 9 UV LED Varnishes/Adhesives .........................................................................10
Flexo - UV Inks ......................................................................................................14Rotary Screen- UV Inks .....................................................................................15
Letterpress/Offset - UV Inks ...........................................................................21UV Varnishes/Adhesives ..................................................................................23
Flexo - Water Based Inks .................................................................................38Water Based Coatings/Adhesives ................................................................38
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Nearly 100 Years of Inks & Coatings InnovationFocused on Your Flexographic, Screen and Digital Printing Ink Needs
The Nazdar® company manufacturers the most comprehensive selection of UV, UV-LED and water-base
flexographic inks, screen printing inks, and wide-format digital inks obtainable from a single source. Nazdar®
inks are primarily used by printers in Roll Label & Packaging, Point of Purchase (POP), Banner, Container,
Industrial, Metal, Ad Specialty, Nameplate / Membrane Switch, Sign and Textile decorating markets. Nazdar®
digital printing inks can be used in a wide selection of digital inkjet printing presses like VUTEk™, NUR™,
Scitex™, Mutoh™, Océ™, Mimaki™ and Gandi™, Hewlett-Packard, Epson®, Roland™, Agfa™, Teckwin™ and other
notable wide-format digital printers. Whether printing indoor or outdoor applications on paper, plastics, textiles,
metal, glass, or containers and packaging, there’s a Nazdar® ink that’s right for every job.
Nazdar accepts responsibility as a corporate citizen and acknowledges our obligation to help improve the
quality of the environment, society, and community of which we are a part. We are committed to formulate all
our products with environmental advantages in mind, including more energy efficient UV curing inks that are
V-Pyrol® free and heavy metal free solvent based inks designed to have lower VOCs and easy reclamation.
Nazdar also provides extensive regulatory compliance training to industry associations and printers. Nazdar®
Shawnee’s QMS have received ISO 9001:2015 certification.
Introduction to Nazdar Inks
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
The continuing evolution of communications technology has brought faster access to product information, service
and support for on-line users everywhere, including the screen printing industry. Nazdar was one of the first screen
printing ink manufacturers to have a presence on the World Wide Web and continues to remain at the forefront of on-
line services by offering a wealth of information and educational interactive opportunities to our web site’s visitors.
The Nazdar On-Line web site is a printer’s gateway to the latest news and technical information concerning Nazdar’s
products and services. It’s also the best way to keep up with what’s happening locally by visiting the special Nazdar
branch location web sites within Nazdar On-Line. That’s just the beginning. Nazdar On-Line also provides dates
and locations for national and regional trade shows and educational seminars, and links to other important on-line
printing resources. Nazdar on-Line provides an area where printers can download valuable software to assist in color
calibration and color matching. Direct e-mail links to Nazdar departments such as customer service, technical service,
and regulatory compliance provide fast response to any questions concerning Nazdar products.
If you’ve visited the Nazdar On-Line site in the past, stop by again; we’re continually updating and improving our
programming and information. We’re sure you’ll find it both educational and informative.
Ink AnswersThe Ink Answers service has become an incredibly useful communication tool for Nazdar’s distributors, salesforce and
end-users. If you have an ink question email: [email protected].
www.Nazdar.com/NarrowWeb
Nazdar On-Line
Got ink questions? We have ink answers.
Nazdar.com
UV LED - NARROW WEB INKS
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
UV LED - NARROW WEB INKS
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
6800 Series UV LED Flexo Ink (Light Emitting Diode) 6800 Series UV LED (Light Emitting Diode) Flexo Ink is specifically formulated for Tag, Label and Packaging applications. These inks have excellent rheology characteristics making them ideal for most printing equipment and product applications. These inks have been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
PRODUCT OFFERINGProcess ColorsStandard process colors are formulated to print using an anilox volume of 0.8 -1.5 BCM.
Base ColorsStandard base colors are designed to be high strength, and formulated to print using anilox volume of 2.5 –3.5 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per ContainerOpaque White: 11 lb, 50 lb, Base Transparent White: 8lb, 40 lbOther Colors: 9 lb, 45 lb, Overprint Varnish: 8 lb, 40 lb
Stock No. Base Printing Colors
6808 Base White/Blanco (BW8)
6809 Base Black/Negro (BW8)
6810 Base Transparent White/Blanco Use to reduce strength and viscosity.
6811 Base Yellow/Amarillo (BW5)
6812 Base Orange/Naranja(BW6)
6813 Base Warm Red/Rojo (BW5)
6814 Base Rubine Red/Rojo (BW4)
6815 Base Rhodamine Red/Rojo (BW4)
6816 Base Purple/Morado (BW4)
6817 Base Violet/Violeta (BW5)
6818 Base Reflex Blue/Azul (BW5)
6819 Base Process Blue/Azul (BW8)
6820 Base Green/Verde (BW8)
6860 Base Transparent White/Blanco Use to reduce strength.
Stock No. Other Colors
6801 Opaque White
6849 Dense Black
Stock No. Fade Resistant (FR) Colors
6821 FR Yellow/Amarillo (BW7)
6822 FR Orange/Naranja (BW7)
6823 FR Warm Red/Rojo (BW7)
6824 FR Rubine Red/Rojo (BW8)
6825 FR Rhodamine Red/Rojo (BW8)
6826 FR Purple/Morado (BW8)
6827 FR Violet/Violeta (BW8)
6828 FR Reflex Blue/Azul (BW8)
Stock No. Process Colors
6841 Process Yellow/Amarillo (BW5)
6842 Process Magenta/Rojo (BW5)
6843 FR Process Cyan /Azul (BW8)
6844 FR Process Black/Negro (BW8)
6847 FR Process Yellow/Amarillo (BW7)
6848 FR Process Magenta/Rojo (BW8)
Stock No. HS Process Colors
68HS41 Process High Speed Yellow (BW5)
68HS42 Process High Speed Magenta (BW5)
68HS43 Process High Speed Cyan (BW8)
68HS44 Process High Speed Black (BW8)
HS inks are formulated for high speed applications, up to 1000 fpm.
Stock No. LS Process Colors
68LS41 Process LS Yellow (BW5)
68LS42 Process LS Magenta (BW5)
68LS43 Process LS Cyan (BW8)
68LS44 Process LS Black (BW8)
LS inks are formulated to run up to 500 fpm.
Stock No. Expanded Gamut Colors
6820 ECG Green (BW8)
6822 ECG Orange (BW5)
6827 ECG Violet (BW8)
68HS20 ECG High Speed Green (BW8)
68HS22 ECG High Speed Orange (BW5)
68HS27 ECG High Speed Violet (BW8)
Stock No. Additives
RE393 UV Reducer (Up to 10% by weight)
CARE97 Photoinitiator for dark colors
CARE71 Non Silicone Defoamer
CARE41 Silicone Leveling Agent
Stock No. Cleaners
NWC10 EZ Cleaner
APPLICATION AND USESubstrates:Pressure sensitive vinyl, top coated and print treated polyester,
UV LED - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
BOPP films, polyethylene, polystyrene, coated paper & board, PETG, PVC shrink, direct thermal.
Anilox RollsProcess Printing: 0.8 –1.5BCMSolid & Line Printing: 2.5 –3.5 BCM
Plates6800 Series UV LED Flexo Ink is compatible with most UV Flexo plates currently on the market.
Printing6800 Series UV LED Flexo Ink can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
LED Cure Parameters6800 Series UV LED Flexo Ink cures at web speeds in excess of 500 fpm (152m/min) when exposed to a 16W/cm2 UV LED curing lamp, with an output wavelength of 395nm.
AdditivesAll additives should be thoroughly mixed into the ink before each use. Please refer to the 6800 Series UV LED Flexo Additive guide for troubleshooting and usage information, or contact Nazdar for more information.Clean UpUse NWC10 EZ Cleaner.Fade Resistance6800 Series UV LED Flexo Inks are formulated with standard and fade resistant (FR) pigments. Storage and Handling6800 Series UV LED Flexo Ink is formulated to be press ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. To prevent premature cure or gelling, keep away from heat, flame and direct light sources. Proper personal protection equipment is required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink
Performance Verification.After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
68NC Series Nestlé Compliant UV LED Flexo Ink68NC Series UV LED (Light Emitting Diode) Flexo Ink is specifically formulated for Tag, Label and Packaging applications. These inks have excellent rheology characteristics making them ideal for most printing equipment and product applications.These inks were formulated for use with UV LED curing lamps of at least 8W/cm2, which have an output wavelength of 395nm. 68NC Series UV LED (Light Emitting Diode) Flexo Ink was formulated using
ingredients as specified by the “Nestle Guidance Note on Packaging Ink - Version 02-2014”
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene, coated paper & board, PETG, PVC shrink, direct thermal paper.
Plates:68NC Series UV LED Flexo Ink is compatible with most UV Flexo plates currently on the market.
Printing:68NC Series UV LED Flexo Ink can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
LED Cure Parameters:68NC Series UV LED Flexo Ink cures at web speeds in excess of 700 fpm (210m/min) when exposed to a 16W/cm2 UV LED curing lamp, with an output wavelength of 395nm.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:68NC Series UV LED Flexo Ink is formulated to be press ready. Thoroughly mix the ink prior to printing.Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. To prevent premature cure or gelling, keep away from heat, flame and direct light sources. Proper personal protection equipment is required when handling this material. Please consult MSDS for details on proper handling of this material.Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: migration, cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using an anilox volume of 0.8 -2.0 BCM.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volume of 2.0 – 4.5 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per Container:Opaque WhiteBase Transparent White Other ColorsOverprint Varnish11 lb, 50 lb 8 lb, 40 lb 9 lb, 45 lb 8 lb, 40 lb
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Stock No. Base Printing Colors
68NC08 Base White/Blanco (BW8)
68NC09 Base Black/Negro (BW8)
68NC10 Base Transparent White/Blanco Use to reduce strength and viscosity.
68NC11 Base Yellow/Amarillo (BW5)
68NC21 FR Yellow/Amarillo (BW7)
68NC12 Base Orange/Naranja(BW6)
68NC22 FR Orange/Naranja (BW7)
68NC13 Base Warm Red/Rojo (BW5)
68NC23 FR Warm Red/Rojo (BW7)
68NC14 Base Rubine Red/Rojo (BW4)
68NC24 FR Rubine Red/Rojo (BW8)
68NC25 FR Rhodamine Red/Rojo (BW8)
68NC26 FR Purple/Morado (BW8)
68NC27 FR Violet/Violeta (BW8)
68NC28 FR Reflex Blue/Azul (BW8)
68NC19 Base Process Blue/Azul (BW8)
68NC20 Base Green/Verde (BW8)
68NC60 Base Transparent White/Blanco Use to reduce strength.
Stock No. Other Colors
68NC01 Opaque White
Stock No. Process Colors
68NC41 Process Yellow/Amarillo (BW5)
68NC42 Process Magenta/Rojo (BW5)
68NC43 FR Process Cyan /Azul (BW8)
68NC44 FR Process Black/Negro (BW8)
68NC47 FR Process Yellow/Amarillo (BW7)
68NC48 FR Process Magenta/Rojo (BW8)
Stock No. Expanded Gamut Colors
68NC20 Green
68NC22 Orange
68NC27 Violet
Stock No. Cleaner
NWC10 EZ Cleaner
6800 Series UV LED Flexo Metallic Ink6800 Series UV LED (Light Emitting Diode) Flexo Metallic Inkis specifically formulated for Tag and Label applications. These inks have excellent rheology characteristics making them ideal for most printing equipment and product applications.These Dual Cure inks have been specifically formulated for use with 16W/cm2 UV LED curing lamps (with an output wavelength of 395nm), or conventional Hg UV lamps.
PRODUCT OFFERINGPackaging Per ContainerSilver 8 lb,Gold 10 lb
Stock No. Metallic Printing Colors
682871 UV LED Flexo 871 Gold
682872 UV LED Flexo 872 Gold
682873 UV LED Flexo 873 Gold
682874 UV LED Flexo 874 Gold
682875 UV LED Flexo 875 Gold
682876 UV LED Flexo 876 Gold
682VMS UV LED Flexo Sterling Silver VMP
Stock No. Additives
CARE 86 UV initiator
RE306 UV Reducer
Stock No. Cleaners
NWC10 EZ Cleaner
APPLICATION AND USESubstrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene, coated paper & board.
Anilox RollsProcess Printing: 0.8 – 1.5 BCMSolid & Line Printing: 2.5 – 3.5 BCM
Plates6800 Series UV LED Flexo Metallic Ink is compatible with most UV Flexo plates currently on the market.
Printing6800 Series UV LED Flexo Metallic Ink Series can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Clean UpUse NWC10 EZ Cleaner.
Fade Resistance6800 Series UV LED Flexo Metallic Silver inks have Blue Wool values of 7-8 and Bronze inks are 5.
UV LED - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Storage and Handling6800 Series UV LED Flexo Metallic Ink is formulated to bepress ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. To prevent premature cure or gelling, keep away from heat, flame and direct light sources. Proper personal protection equipment is required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Shelf Stability.The UV Flexo Metallic Ink Series in unopened containershave 6 months shelf life. Although useable after 6 months,some loss of brilliance may occur.
8700 Series UV LED Rotary Screen Ink(Light Emitting Diode) 8700 Series UV LED (Light Emitting Diode) Rotary Screen Ink is formulated specifically for roll label applications. The 8700 Series exhibits exceptional print characteristics such as adhesion to a wide range of substrates, high gloss, abrasion resistance and excellent chemical resist. These inks were formulated for use with UV LED curing lamps of at least 8W/cm2, which have an output wavelength of 395nm.
PRODUCT OFFERINGStandard Printing ColorsThe 8700 series Base Colors have excellent opacity, flow characteristics, and are press ready. The 8700 base colors and 8776 UV LED No-Sil White are designed to be overprinted by other printing technologies such as 6800 Series UV LED Flexo Ink, (see 6800 Series technical data sheet for more information).The 8700 Series standard printing colors can be used in matches to achieve Pantone® color simulations. These blend formulations are available at www.nazdar.com.
Packaging Per ContainerOpaque White 11 lb, 50 lbBase Transparent White 8 lb, 40 lbOther Colors 9 lb, 45 lbOverprint Varnish 8 lb, 40 lb
Non Silicone
Standard Printing Colors
87410 Base Transparent White/Blanco
87458 Base White/Blanco (BW8)
87459 Base Black/Negro (BW8)
87460 Base Orange/Naranja (BW6)
87461 Base Yellow/Amarillo (BW5)
87462 Base Warm Red/Rojo (BW5)
87463 Base Rubine Red/Rojo (BW4)
87464 Base Rhodamine Red/Rojo (BW4)
87465 Base Purple/Morado (BW4)
87466 Base Violet/Violeta (BW5)
87467 Base Reflex Blue/Azul (BW5)
87468 Base Process Blue/Azul (BW8)
87469 Base Green/Verde (BW8)
Stock No. Other Colors
8776 Opaque Non Silicone White
Stock No. Cleaners
NWC10 EZ Cleaner
APPLICATION AND USESubstrates:Pressure sensitive vinyl, coated paper and board, top coated and print treated polyester, BOPP films, polyethylene and polystyrene.
Mesh Selection:Rotary Screen: Use rotary screens which will deposit 5 to 15 microns of ink film thickness.Flat Screens: Use 305 - 420 tpi (120-165 tpcm) monofilament polyester mesh.
LED Cure Parameters:8700 Series ink cures up to 300 fpm (90m/min) when exposed to a 16W/cm2 UV LED curing lamp, with an output wavelength of 395nm.
AdditivesAll additives should be thoroughly mixed into the ink before each use. Prior to production, test any additive adjustment to the ink.
Clean UpUse NWC10 EZ Cleaner.
Storage and HandlingThe 8700 Series ink is formulated to be press ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. Keep away from heat, flame and direct light sources. Otherwise, premature cure or gel could occur.Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Performance Verification.After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
UV LED - Rotary Screen
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
UV LED - Varnishes/Adhesives
OP61003 UV LED Gloss VarnishOP61003 UV LED Gloss Varnish is a Premium Gloss Over Print Varnish that exhibits high gloss and is specifically formulated for Tag and Label printing. The overprint clear has excellent rheology characteristics making it ideal for most printing equipment, and product applications. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Gloss: 90+ (60°) Shelf Life: 6 months (Unopened containers)Benzophenone (BP) This product is not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 -10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
UV LED - Varnishes/Adhesives OP61004 UV LED Gloss Imprintable VarnishOP61004 UV LED Gloss Imprintable Varnish is used to provide a stampable/imprintable coating over many water based, solvent based, and UV curable inks. OP61004 exhibits high gloss and is specifically formulated for Tag and Label printing. The overprint clear has excellent rheology characteristics making it ideal for most printing equipment, and product applications. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP62001 UV LED Matte VarnishOP62001 UV LED Matte Varnish is a very versatile matte UV LED coating that offers a smooth low gloss finish, high scuff resistance and fast cure. This coating has excellent rheology characteristics making it ideal for most printing equipment, and product applications. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Shelf Life: 6 months (Unopened containers)Benzophenone (BP) This product is formulated with Benzophenone.
Application Suggestions:
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP63000 UV LEDLaminating AdhesiveOP63000 UV LED Laminating Adhesive was developed to bond clear films to various films, papers, and foil substrates. OP Series UV Flexo Adhesives are specifically formulated for Tag and Label printing. The laminating adhesives have excellent rheology characteristics making them ideal for most printing equipment, and product applications. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Gloss: 90+ (60°) Shelf Life: 6 months (Unopened containers)Benzophenone (BP) This product is formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 -10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the
full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP63016 UV LEDCold Foil AdhesiveOP63016 Cold Foil Adhesive is a non pressure-sensitive adhesive designed to be printed, wet laminated, and cured through special transparent cold foil films. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
The product should be mixed prior to use.
OP69001 UV LEDRelease VarnishOP69001 UV LED Release Varnish is specifically formulated to be used as a release coating. This coating has excellent rheology characteristics making it ideal for most printing equipment, and product applications. This coating has been specifically formulated for use with 16W/cm2 UV LED curing lamps, which have an output wavelength of 395nm.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Properties:Shelf Life: 6 months (Unopened containers)Benzophenone (BP) This product is formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 -10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
UV - NARROW WEB INKS
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
specifications only low odor and non-migratory approved cleaning solvents from the Nestle’ list should be used.
Fade Resistance:92NCF Series UV Flexo Shrink Sleeve Ink are designed for interior applications only. The colors designated with (FR) use pigments which have extended fade resistance.
Storage and Handling:92NCF Series UV Flexo Shrink Sleeve Ink is formulated to be press ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. To prevent premature cure or gelling, keep away from heat, flame and direct light sources. Proper personal protection equipment is required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink. 92NCF Series UV Flexo Shrink Sleeve Ink is a one-part, 100% solids UV-curable Flexo printing ink and does not contain HDODA or Benzophenone.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: migration, cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
PRODUCT OFFERINGTo maintain the integrity of the 92NCF formulation, only approved inks and additives from this sheet may be intermixed.
Standard Printing White92NCF01 NC UV Flxo Opq Shrnk Wht 1P White and 6003008092 NC UV Flxo Opq Shrnk Wht 4P are press ready and have excellent opacity, flow and adhesion characteristics. These whites are NOT designed to mix with any other 92NCF Base Colors.
Process ColorsStandard process colors are formulated to print using up to 1200 line (0.8 bcm) anilox.
Base Colors92NCF Base Colors are designed to be high strength. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per ContainerOpaque White: 11 lb, 50 lbBase Transparent White: 8 lb, 40 lbOther Colors: 9 lb, 45 lbOver Print Varnish: 8 lb, 40 lb
Stock No. Base Printing Colors
92NCF09 Base Black/Negro (BW8)
92NCF10 Base Transparent White/Blanco Use to reduce strength and viscosity.
92NCF60 Base Transparent White/Blanco Use to reduce strength.
92NCF11 Base Yellow/Amarillo (BW5)
92NCF12 Base Orange/Naranja(BW6)
92NCF Series UV Flexo Ink92NCF Series UV Flexo Shrink Sleeve Ink is specifically formulated for shrink sleeve applications where extremely low odor is necessary. The ink is highly flexible, and has excellent rheology characteristics making it ideal for most printing equipment, and shrink sleeve applications. 92NCF Series UV Flexo Shrink Sleeve Ink will shrink up to 70%, depending on application. Cure Parameters 92NCF Series UV Flexo Shrink Sleeve Ink was formulated using ingredients as specified by the “Nestle Guidance Note on Packaging Ink - version 02-2014”
Migration Testing:92NCF Series UV Flexo Shrink Sleeve Ink is formulated with low migration materials recommended by Nestle’. The final converter should determine suitability of the end application by appropriate migration testing. Although the 92NCF Series UV Flexo Shrink Sleeve Ink is formulated to comply with Nestle’ listed materials, all possible sources of migration and contamination should be evaluated for compliance. These include but are not limited to: press wash, ink, substrate, storage and proper cure.
Substrates:PVC, PETG, PLA and Polystyrene. (Orientation of the material can be MDO or TDO); also BOPP films, polyethylene, coated paper and board. Corona treatment may be necessary for some applications.
Anilox Rolls: 300-1200 line (cells per inch) corresponding to a volume from 7.5 to 0.8 bcm.
Plates:92NCF Series UV Flexo Shrink Sleeve Ink is compatible with most UV Flexo plates on the market.
Printing:92NCF Series UV Flexo Shrink Sleeve Ink is formulated to be press ready. 92NCF Series UV Flexo Shrink Sleeve Ink is also suitable for surface printing. 92NCF Series UV Flexo Shrink Sleeve Ink can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:92NCF Series UV Flexo Shrink Sleeve Ink cures when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch. Thorough cure is critical to low odor and low migration. These guidelines are intended only as a starting point for determining cure parameters, which must be determined under actual production conditions.
Additives:All additives should be thoroughly mixed into the ink before each use. Prior to production, test any additive adjustment to the ink. Only Nestle’ compliant additives should be used.
Clean Up:For general clean up use NWC10 EZ Cleaner. To meet Nestle’
UV - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
92NCF13 Base Warm Red/Rojo (BW5)
92NCF14 Base Rubine Red/Rojo (BW4)
92NCF19 Base Process Blue/Azul (BW8)
92NCF20 Base Green/Verde (BW8)
Stock No. Fade Resistant (FR) Colors
92NCF21 FR Yellow/Amarillo (BW7)
92NCF22 FR Orange/Naranja (BW7)
92NCF23 FR Warm Red/Rojo (BW7)
92NCF24 FR Rubine Red/Rojo (BW8)
92NCF25 FR Rhodamine Red/Rojo (BW8)
92NCF26 FR Purple/Morado (BW8)
92NCF27 FR Violet/Violeta (BW8)
92NCF28 FR Reflex Blue/Azul (BW8)
Stock No. Process Colors
92NCF41 Process Yellow/Amarillo (BW5)
92NCF42 Process Magenta/Rojo (BW5)
92NCF43 FR Process Cyan /Azul (BW8)
92NCF44 FR Process Black/Negro (BW8)
92NCF47 FR Process Yellow/Amarillo (BW7)
92NCF48 FR Process Magenta/Rojo (BW8)
Stock No. Opaque Whites
92NCF01 NC UV Flxo Opq Shrnk Wht 1P
6003008092 NC UV Flxo Opq Shrnk Wht 4P
Stock No. Cleaner
NWC10 EZ Cleaner
9300 Series UV Flexo Ink9300 Series UV Flexo Ink was specifically formulated for Tag, Label and Shrink Sleeve printing. These inks have excellent rheology characteristics making them ideal for most flexographic printing equipment and product applications.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene, coated paper & board and shrink films.
Printing:9300 Series UV Flexo Ink can be printed over Rotary Screen 8376 No-Sil Combination White. (See the 8300 Series technical data sheet for more information). 9300 Series UV Flexo Ink is formulated to be press ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°- 32°C) for optimum print and cure performance. Pretest to determine optimum printing performance for each set of ink, substrate, anilox, press, curing variables/conditions and any post printing
processes. 9300 Series UV Flexo Ink can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:9300 Series UV Flexo Ink cures when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch.
Clean Up:Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°- 90°F (18°-32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Storage:Store tightly covered at temperatures between 65°-90°F (18°-32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Direct skin contact to UV inks is the primary route of exposure and irritation. Therefore, it is recommended that all personnel handling UV products wear gloves and barrier cream to prevent direct skin contact. Safety glasses are suggested in areas where ink may be splashed. If ink does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the 9300 Series Material Safety Data Sheet for further instructions and warnings. The 9300 Series Standard Bases, Fade Resistant Bases and Process Colors are HDODA and Benzophenone free.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
PRODUCT OFFERINGPackaging Per Container
Process ColorsStandard process colors are formulated to print using up to 1200 line (0.8 bcm) anilox.
Base ColorsStandard base colors are designed to be high strength, and formulated to print using anilox volume of 2.5 – 3.5 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Other Available ProductsFluorescents - See UV Flexo Fluorescent Data Sheet Metallics - See UV Flexo Metallic Data Sheet
Packaging Per ContainerOpaque White: 11 lb, 50 lbBase Transparent White: 8 lb, 40 lb Other Colors: 9 lb, 45 lbOverprint Varnish: 8 lb, 40 lb
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Stock No. Base Printing Colors
9308 Opaque Base White/Blanco (BW8)
9309 Base Black/Negro (BW8)
9310 Base Transparent White/Blanco Use to reduce strength and viscosity.
9311 Base Yellow/Amarillo (BW5)
9312 Base Orange/Naranja(BW6)
9313 Base Warm Red/Rojo (BW5)
9314 Base Rubine Red/Rojo (BW4)
9315 Base Rhodamine Red/Rojo (BW4)
9316 Base Purple/Morado (BW4)
9317 Base Violet/Violeta (BW5)
9318 Base Reflex Blue/Azul (BW5)
9319 Base Process Blue/Azul (BW8)
9320 Base Green/Verde (BW8)
9360 Base Transparent White/Blanco Use to reduce strength.
9349 Dense Black (BW8)
93012 Base Yellow 012 (BW5)
93021 Base Orange 021 (BW5)
93032 Base Red 032 (BW5)
93072 Base Blue 072 (BW5)
Stock No. Fade Resistant (FR) Colors
9321 FR Yellow/Amarillo (BW7)
9322 FR Orange/Naranja (BW7)
9323 FR Warm Red/Rojo (BW7)
9324 FR Rubine Red/Rojo (BW8)
9325 FR Rhodamine Red/Rojo (BW8)
9326 FR Purple/Morado (BW8)
9327 FR Violet/Violeta (BW8)
9328 FR Reflex Blue/Azul (BW8)
Stock No. Process Colors
9341 Process Yellow/Amarillo (BW5)
9342 Process Magenta/Rojo (BW5)
9343 FR Process Cyan /Azul (BW8)
9344 FR Process Black/Negro (BW8)
9347 FR Process Yellow/Amarillo (BW7)
9348 FR Process Magenta/Rojo (BW8)
Stock No. Opaque Whites
9301 Opaque Printing White Not for blending / Not low odor.
Stock No. Shrink Opaque Whites
6002056492 92 UV Flxo Opq Shrnk Wht 2P
6003245092 92 UV Flxo Opq Shrnk Wht Rapid
6003398892 92 UV Flxo Opq Shrnk Wht Rsist
6004055792 92 Shrink White LOLM 10128 Low odor low migration
6004000892 92 UV Flexo Shrink White HS
Stock No. Additives
RE392 UV Reducer
CARE41 Silicone Leveling Agent
CARE70 UV Photoinitiator
CARE71 Non-silicone Defoamer
CARE86 UV Photoinitiator
Stock No. Cleaner
NWC10 EZ Cleaner
UV Flexo Polar White InkUV Flexo Polar White Ink exhibits high opacity and is specifically formulated for tag and label printing. 9300 Series UV Flexo Polar White Ink is designed to provide a high opacity rotary screen look and feel at UV flexo speeds. 9300 Series UV Flexo Polar White Ink has excellent rheology characteristics and gloss making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene and polystyrene. Note: As with all film substrates, lots may vary and testing is recommended before use.
Anilox Rolls: Anilox rolls with a volume of at least 15BCM are recommended for best results.
Plates:This Ink Series is compatible with most water based flexo plates on the market.
Printing:Softer plates, harder tapes and minimal nip pressure are recommended for best results. This Ink Series can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:This Ink Series is formulated to cure using a medium pressure mercury vapor lamp set at 300-600 watts per inch.
Clean Up:Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°- 90°F (18°-32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
UV - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: migration, cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
PRODUCT OFFERINGPackaging Per Container
Polar White 11 lb, 50 lb
Stock No. Standard Colors
9391 Polar White II
9400 Series UV Flexo Ink 9400 Paper Series UV Flexo Ink was specifically formulated for Tag and Label printing. These inks have excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Paper, Board and some films.
Anilox Rolls: 300-1200 line (cells per inch) corresponding to a volume from 7.5 to 0.8 bcm.
Plates:9400 Series is compatible with most UV Flexo plates on the market.
Printing:9400 Series can be printed over Rotary Screen 8376 No-Sil Combination White. (See the 8300 Series technical data sheet for more information). The 9400 Series ink is formulated to be press ready. Thoroughly mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°- 32°C) for optimum print and cure performance. Pretest to determine optimum printing performance for each set of ink, substrate, anilox, press, curing variables/conditions and any post printing processes. The 9400 Series can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:9400 Series ink cures at web speeds up to 1000 fpm when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch. These guidelines are intended only as a starting point for determining cure parameters, which must be determined under actual production conditions.
Clears / Varnishes:9410 Base Transparent White can be used to reduce the strength of the base, process, and fluorescent colors.
Additives:All additives should be thoroughly mixed into the ink before each use. Prior to production, test any additive adjustment to the ink.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
GENERAL INFORMATION Ink Handling:Direct skin contact to UV inks is the primary route of exposure and irritation. Therefore, it is recommended that all personnel handling UV products wear gloves and barrier cream to prevent direct skin contact. Safety glasses are suggested in areas where ink may be splashed. If ink does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the 9400 Series Material Safety Data Sheet for further instructions and warnings. The 9400 Series ink is a one-part, 100% solids UV-curable Flexo printing ink and does not contain HDODA or Benzophenone.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Fade Resistance:The 9400 Series inks are designed for interior applications only. The colors designated with (FR) use pigments which have extended fade resistance.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using up to 1200 line (0.8 bcm) anilox.
Base Colors:9400 Base Colors are designed to be high strength. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Other Available Products:Fluorescent Colors – See UV Flexo Fluorescent Data Sheet. Metallic Colors- See UV Flexo Metallic Data Sheet.
Packaging:The Opaque White is available in 11 lb and 50 lb containers, Base Transparent White is available in 8 lb and 40 lb containers, all other colors are available in 9 lb and 45 lb containers.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Stock No. Base Printing Colors
9408 Opaque Base White/Blanco (BW8)
9409 Base Black/Negro (BW8)
9410 Base Transparent White/Blanco
9411 Base Yellow/Amarillo (BW5)
9412 Base Orange/Naranja(BW6)
9413 Base Warm Red/Rojo (BW5)
9414 Base Rubine Red/Rojo (BW4)
9415 Base Rhodamine Red/Rojo (BW4)
9416 Base Purple/Morado (BW4)
9417 Base Violet/Violeta (BW5)
9418 Base Reflex Blue/Azul (BW5)
9419 Base Process Blue/Azul (BW8)
9420 Base Green/Verde (BW8)
Stock No. Fade Resistant (FR) Colors
9421 FR Y ellow/Amarillo (BW7)
9422 FR Orange/Naranja (BW7)
9423 FR Warm Red/Rojo (BW7)
9424 FR Rubine Red/Rojo (BW8)
9425 FR Rhodamine Red/Rojo (BW8)
9426 FR Purple/Morado (BW8)
9427 FR Violet/Violeta (BW8)
9428 FR Reflex Blue/Azul (BW8)
Stock No. Process Colors
9441 Process Y ellow/Amarillo (BW5)
9442 Process Magenta/Rojo (BW5)
9443 FR Process Cyan /Azul (BW8)
9444 FR Process Black/Negro (BW8)
9447 FR Process Yellow/Amarillo (BW7)
9448 FR Process Magenta/Rojo (BW8)
Stock No. Additives
RE393 UV Reducer (Up to 10% by weight)
Stock No. Cleaner
NWC10 EZ Cleaner
UV Flexo Metallic Ink The UV Flexo Metallic Ink Series is an ink system which offers high brilliance and good printability.
Substrates:Paper, Paperboard, and various films.
Clean Up: Use NWC10 EZ Cleaner
Storage and Handling:These inks are formulated to be press ready. Thoroughly mixthe ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. To prevent premature cure or gelling, keep away from heat, flame and direct light sources. Proper personal protection equipment is required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Fade Resistance:UV Flexo Metallic Ink is designed for interior applications only.
Shelf Stability:The UV Flexo Metallic Ink Series in unopened containers will have a minimum of 3 months shelf stability. Although useable after 3 months, some loss of brilliance may occur.
Benzophenone:These inks are formulated without benzophenone.
PRODUCT OFFERING
Stock No. Metallic Printing Colors
699402UM UV Flexo 876 Gold
699424UM UV Flexo 872 Gold
699425UM UV Flexo 873 Gold
699426UM UV Flexo 874 Gold
699427UM UV Flexo 871 Gold
699428UM UV Flexo 875 Gold
699429UM UV Flexo 877 Silver
699430UM UV Flexo 877 Silver 2
60028294UM UV Flexo Shrink Silver
Stock No. Additives
CARE 86 UV Initiator
RE393 UV Reducer
Stock No. Cleaner
NWC10 EZ Cleaner
UV - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
8300 Series UV Rotary Screen Ink8300 Series UV Rotary Screen Ink is formulated specifically for roll label applications. The 8300 Series exhibits exceptional print characteristics such as adhesion to a wide range of substrates, high gloss, abrasion resistance and excellent chemical resist.
Substrates:Pressure sensitive vinyls, coated paper and board, top coated and print treated polyester, BOPP films, polyethylene and polystyrene.Surface energy of substrates should be at least 40 dynes/cm to achieve proper adhesion. The use of in-line, on press corona treatment can increase the dyne level of many substrates.
Mesh Selection:Rotary Screen: Use rotary screens which will deposit 5 to 15 microns of ink film thickness.Flat Screens: Use 305 - 420 tpi (120-165 tpcm) monofilament polyester mesh.
Cure Parameters:7400 UV Letterpress Series ink cures at web speeds up to 500 fpm when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch. These guidelines are intended only as a starting point for determining cure parameters, which must be determined under actual production conditions
Stencil:Solvent resistant, UV ink compatible direct emulsions and capillary films.
Squeegee:65-90 durometer polyurethane squeegee.
Coverage:2500 - 3500 square feet (232 – 325 square meters) per gallon depending upon ink deposit.
Cure Parameters:8300 Series ink cures when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch at web speeds of up to 250 ft/min. Cure parameters must be determined under actual production conditions.
Additives:All additives should be thoroughly mixed into the ink before each use. Prior to production, test any additive adjustment to the ink.
Clean Up:Use NWC10 EZ Cleaner.
Fade Resistance:The 8300 Series inks are designed for interior applicationsonly. The colors designated with (FR) use pigments which have extended fade resistance.
Storage and Handling:The 8300 Series ink is formulated to be press ready. Thoroughly
mix the ink prior to printing. Maintain ink temperature at 65°-90°F (18°-32°C) for optimum print and cure performance. Keep away from heat, flame and direct light sources. Otherwise, premature cure or gel could occur. Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Standard Printing Colors:The 83300/83400 series Base Colors have excellent opacity, flow characteristics, and are press ready.The 83400 base colors and 8376 No-Sil Combination White are designed to be overprinted by other printing technologies such as 9300 Series UV Flexo, (see 9300 Series technical data sheet for more information).The 8300 Series standard printing colors can be used in matches to achieve Pantone® color simulations. These blend formulations are available at www.nazdar.com.
Overprint/Mixing Clears:8327 Mixing/Overprint Clear contains silicone and can be used to reduce the density of colors, or as a clear base for special effect additives such as Metallics.83410 Transparent White is non- silicone based and can be used to reduce the density of the 83400 colors or as a clear base for special effects additives such as Metallics..
Flourescent Colors:The 8300 series fluorescent colors have the tendency to settle; so high speed mixing is required prior to printing. Fluorescent colors fade with exposure to ultraviolet light. This includes outdoor exposure as well as UV lamp exposure. It is therefore recommended to adjust art so these colors are the final colors printed on any image.
Tactile Inks:Tactile inks are available; please see the UV Rotary Screen Tactile Ink Technical Data Sheet for more information.
Overprint Clears:UV Rotary Screen Overprint Clears are also available; please consult the corresponding Technical Data Sheet for details of these items.
Packaging:The Opaque Whites are available in 11 lb and 50 lb containers, Mixing/Overprints Clears are available in 8 lb and 40 lb containers, all other colors are available in 9 lb and 45 lb containers.Additives/Reducers are available in quart and gallon containers.Cleaners are available in 8 lb, 40 lb and 468 lb containers.
UV - Rotary Screen
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Silicone Non-Silicone Standard Printing Colors
– 83410 Transparent White
8327 – Mixing/Over Print Clear
83358 83458 Tinting White
83359 83459 Tinting Black
83360 83460 Orange
83361 83461 Yellow
83362 83462 Warm Red
83363 83463 Rubine Red
83364 83464 Rhodamine Red
83365 83465 Purple
83366 83466 Violet
83367 83467 Reflex Blue
83368 83468 Process Blue
83369 83469 Green
Stock No. Non-Silicone Containing Whites
8376 Combination White
8375 Combo White
6000614483 Combo White
6000248583 Beverage White
Stock No. Silicone Containing Whites
8378 High Intensity White
8379 High Intensity Black
8377 White
Stock No. Flourescent Colors
83520 Orange Yellow
83530 Orange
83540 Orange/red
83550 Red
83560 Cerise
83570 Pink
83580 Blue
83590 Green
83600 Magenta
Stock No. Overprint Colors
OP8001 R/S Gloss OPV Clear (See OP8001 TDS for more details)
OP8002 R/S Gloss Varnish (See OP8002 TDS for more details)
8327 Mixing/Over Print Clear
Stock No. Tactile Varnishes
6000600083 R/S Tactile Varnish - Standard Viscosity (See UV Rotary Screen Tactile Ink TDS
for more details)
600256658 R/S Tactile Varnish - High Viscosity (See UV Rotary Screen Tactile Ink TDS for more
details)
Stock No. Additives/Reducers
RE200 UV Reducer
Stock No. Cleaners
NWC10 EZ Cleaner
UV - Rotary Screen
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
6400 Series UV Flexo Ink6400 Offset Paper Series Ink was specifically formulated for Tag and Label printing. The 6400 has excellent print quality especially at high speeds. The 6400 inks have excellent color strength, curing, adhesion and scratch resistance.
Substrates:6400 UV Offset Series is suitable for a variety of paper substrates such as: Gloss, Semi-gloss, Cast gloss, Bond, Uncoated and folding carton SBS, SUS and CCNB. Also works on some films.
Properties: • Excellent color consistency and mileage• Non - Bleed• Very good adhesion to a wide variety of substrates• Great print quality at high speeds • Excellent curing• High Quality
Plates/Blankets:6400 UV Offset Series is compatible with UV Offset plates and blankets on the market.
Printing:6400 UV Offset Series can be printed over Rotary Screen 8376 No-Sil Combination White, 83400’s and over 9301 Flexo Opaque White (See the 8300 and 9300 Series technical data sheets for more information). Maintain ink temperature at 65°-90°F (18°- 32°C) for optimum print and cure performance. Pretest to determine optimum printing performance for each set of inks, substrate, press, curing variables/conditions and any post printing processes. The 6400 UV Offset Series can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:6400 UV Offset Series ink cures at web speeds up to 1000 fpm when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch. These guidelines are intended only as a starting point for determining cure parameters, which must be determined under actual production conditions.
Ink Handling:Direct skin contact to UV inks is the primary route of exposure and irritation. Therefore, it is recommended that all personnel handling UV products wear gloves and barrier cream to prevent direct skin contact. Safety glasses are suggested in areas where ink may be splashed. If ink does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the 6400 UV Offset Series Material Safety Data Sheet for further instructions and warnings. The 6400 UV Offset Series ink is a one-part, 100% solids UV-curable offset printing ink and does not contain HDODA or Benzophenone.
Trapping:The 6400 UV Offset inks are formulated for tack stepping 14-17@ 800rpm and can be wet trapped.
Standard Printing WhiteThe 6401 Opaque White has excellent opacity and can be used as first down or where opacity is critical when trapping other colors.
Process ColorsThe 6400 UV Offset Series 4 color process inks are based on SWOP standards.
Base ColorsThe 6400 UV Offset Base Series are designed to be high strength. The base colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Additives:Reducer: Use RE364 UV Tack Reducer to reduce the viscosity of the ink. Add 3-4% by weight. Each percentage added will reduce tack 1-2 units @ 800 rpmPhotoinitiator: Use CARE70 to improve cure. Add 1-2% by weight.
Clean Up:Isopropyl alcohol, denatured alcohol or any suitable commercial press wash.
Stock No. Standard Printing Colors
6401 Base Opaque White/Blanco
Stock No. Base Printing Colors
64C09 Base Black/Negro
64C10 Base Transparent White/Blanco
64C11 Base Yellow/Amarillo
64C13 Base Warm Red/Rojo
64C14 Base Rubine Red/Rojo
64C15 Base Rhodamine Red/Rojo
64C16 Base Purple/Morado
64C17 Base Violet/Violeta
64C18 Base Reflex Blue/Azul
64C19 Base Process Blue/Azul
64C20 Base Green/Verde
Stock No. Process Colors
6441 Process Yellow/Amarillo
6442 Process Magenta
6443 Process Cyan/Azul
6444 Process Black/Negro
Stock No. Additives/Reducers
RE364 UV Tack Reducer
CARE70 UV Photoinitiator Dark
UV - Letterpress
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
7400 Series UV Flexo Ink7400 Letterpress Series Ink was specifically formulated for Tag and Label printing. The 7400 has excellent print quality especially at high speeds. The 7400 inks have excellent color strength, curing, adhesion and scratch resistance.
Substrates:7400 UV Letterpress Series is suitable for a variety of treated film and paper substrates such as: BOPP, Polyethylene, Polyester, Gloss, Semi-gloss, Cast gloss, Bond, Uncoated and folding carton SBS, SUS and CCNB. Also works on some films.
Properties: • Excellent color consistency and mileage• Non - Bleed• Very good adhesion to a wide variety of substrates• Great print quality at high speeds • Excellent curing• High Quality
Plates:7400 UV Letterpress Series is compatible with UV Letterpress plates on the market.
Printing:7400 UV Letterpress Series can be printed over Rotary Screen 8376 No-Sil Combination White, 83400’s and over 9301 Flexo Opaque White (See the 8300 and 9300 Series technical data sheets for more information). Maintain ink temperature at 65°-90°F (18°- 32°C) for optimum print and cure performance. Pretest to determine optimum printing performance for each set of inks, substrate, press, curing variables/conditions and any post printing processes. The 7400 UV Letterpress Series can be affected by stray UV light in and around a printing facility. Be aware of skylights, windows and overhead lights curing the ink. Light filters are recommended. Keep ink containers covered when not in use.
Cure Parameters:7400 UV Letterpress Series ink cures at web speeds up to 500 fpm when exposed to a medium pressure mercury vapor lamp set at 300 - 600 watts per inch These guidelines are intended only as a starting point for determining cure parameters, which must be determined under actual production conditions
Ink Handling:Direct skin contact to UV inks is the primary route of exposure and irritation. Therefore, it is recommended that all personnel handling UV products wear gloves and barrier cream to prevent direct skin contact. Safety glasses are suggested in areas where ink may be splashed. If ink does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the 7400 UV Letterpress Series Material Safety Data Sheet for further instructions and warnings. The 7400 UV Letterpress Series ink is a one-part, 100% solids UV-curable Letterpress printing ink and does not contain HDODA or Benzophenone.
Standard Printing WhiteThe 7401 Opaque White has excellent opacity and can be used as first down or where opacity is critical when trapping other colors.
Process ColorsThe 7400 UV Letterpress Series 4 color process inks are based on SWOP standards.
Base ColorsThe 7400 UV Letterpress Base Series are designed to be high strength. The base colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Additives:Reducer: Use RE306 UV Reducer to reduce the viscosity of the ink. Add 3-4% by weight. Each percentage added will reduce tack 1-2 units @ 800 rpm Photoinitiator – Use CARE70 to improve cure.Add 1-2% by weight.
Clean Up:Isopropyl alcohol, denatured alcohol or any suitable commercial press wash.
Stock No. Standard Printing Colors
7401 Base Opaque White/Blanco
Stock No. Base Printing Colors
7409 Base Black/Negro
7410 Base Transparent White/Blanco
7411 Base Yellow/Amarillo
7413 Base Warm Red/Rojo
7414 Base Rubine Red/Rojo
7415 Base Rhodamine Red/Rojo
7416 Base Purple/Morado
7417 Base Violet/Violeta
7418 Base Reflex Blue/Azul
7419 Base Process Blue/Azul
7420 Base Green/Verde
Stock No. Process Colors
7441 Process Yellow/Amarillo
7442 Process Magenta
7443 Process Cyan/Azul
7444 Process Black/Negro
Stock No. Additives/Reducers
RE364 UV Tack Reducer
CARE70 UV Photoinitiator Dark
UV - Letterpress
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
OP1001 UV Flexo GP Varnish AFThe OP1001 UV Flexo GP Varnish is formulated to be non-bleeding and lower odor than other UV varnishes. OP Series UV Flexo Varnishes are specifically formulated for Tag and Label printing. The OP1001 exhibits better rub characteristics than the OP1003. The overprint clears have excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive direct thermal coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 400 cps @25°CCure: 300-600 W/inch Medium Pressure Hg LampGloss: >80 (60°)Rub: 800+ Sutherland Rubs (4lb weight, face to face)Slide: 6-10°Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1001
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1003 UV GP Varnish AFOP1003 is formulated to be non-bleeding and lower odor then other UV Varnishes. The OP1003 is specifically formulated for Tag and Label printing. The overprint varnish has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP film, polyethylene, polystyrene and some paper & board.
Target Viscocity: 400 cps @25°CCure: 300-600 W/inch Medium Pressure Hg LampGloss: >80 (60°)Rub: 500+ Sutherland Rubs (4lb weight, face to face)Slide: 8-12° (face to face)MEK: >50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1003
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur.The product should be mixed prior to use.
OP1005 UV GP Gloss VarnishOP1005 GP UV Flexo Varnish exhibits high gloss and is specifically formulated for Tag and Label printing. The overprint clear has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Cure: 300-600 W/inch Medium Pressure Hg LampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1005
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
UV - Varnishes/Adhesives
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1007 UV Gloss Resist VarnishOP1007 UV Gloss Resist Varnish is specifically formulated for overprinting digitally printed Tag and Label applications. The overprint varnish exhibits high gloss and has excellent rheology characteristics making it ideal for most printing equipment.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and board stocks.
Target Viscocity: 300 cps @25°CCure: 300-600 W/inch Medium Pressure Hg LampGloss: >80 (60°)Rub: 500+ Sutherland Rubs (4lb weight, face to face)Slide: <12° (face to face)MEK: >50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1007
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1008 UV Gloss Resist II VarnishOP1008 UV Gloss Resist Varnish is specifically formulated for overprinting digitally printed Tag and Label applications. OP1008 has better chemical and water resistance when compared with OP1007. The overprint varnish exhibits high gloss and has excellent rheology characteristics making it ideal for most printing equipment.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and board stocks.
Target Viscocity: 310 cps @25°CCure: 300-600 watts/inchGloss: > 75 (60°)Rub: > 500 cycles - 4lb weight, face to faceSlide: <10° (face to face)MEK: >50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1008
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1009 UV Gloss Resist VarnishOP1009 UV Flexo Varnish is a Benzophenone Free Varnish that exhibits high gloss and is specifically formulated for Tag and Label printing. The overprint clear has excellent rheology characteristics,
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
making it ideal for most printing equipment and product applications.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 440 cps @25°CCure: 300-600 watts per inchGloss: >80 (60°)Rub: > 500 cycles - 4lb weight, face to faceSlide: <12° MEK: >50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1010 UV Gloss Flexo VarnishOP1010 is specifically formulated for overprinting digitally printed Tag and Label applications. The overprint varnish exhibits high gloss and has excellent rheology characteristics making it ideal for most printing equipment.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 300 cps @25°CCure: 300-600 watts/inchGloss: >80 (60°)Rub: > 500 cycles - 4lb weight, face to faceSlide: <12° (face to face)MEK: >50 double rubsShelf Life: 6 months (Unopened containers)
Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1010
Application Suggestions:180-360 line (cells per inch) corresponding to a volume from 8.0 to 5.0 bcm. Reverse angle doctor blade is recommended. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1011 UV Gloss Varnish 722OP1011 was formulated with raw materials that comply with the US Food and Drug Administration’s (FDA) Food Contact Notification (FCN) No. 772. This product may be used as described in the FCN No. 772. There are many types of food packages and the printing ink is only one constituent. Nazdar does not control the parameters in food package printing, packing and storage, therefore, Nazdar is not able to issue certificates or declarations of compliance which cover the legal responsibility of the entire packaging chain. The manufacturer of the packaging and the filler are responsible for the properties of the food packaging and its compliance with applicable legal requirements. While technical information and advice on the use of this product is provided in good faith, the User bears sole responsibility for selecting the appropriate product for their end-use requirements. See full disclaimer at the end of the document.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 15-18 sec/#3 ZahnCure: 300-600 watts per inchGloss: >80 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1012 UV Gloss M VarnishOP1012 is specifically formulated for overprinting digitally printed Tag and Label applications. The overprint varnish exhibits high gloss and has excellent rheology characteristics making it ideal for most printing equipment.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 300 cps @25°CCure: 300-600 watts per inchGloss: >80°Rub: > 500 cycles - 4lb weight, face to faceSlide: <12° (face to face)MEK: > 50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1012
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1013 Combo Screen/Coater TCOP1013 has been developed for press application via screen, blanket, tower, dampener, flexo, or converted offset coating units. This topcoat will exhibit excellent flow, leveling properties, resulting in high gloss cured films with excellent flexibility and rub/scuff resistance.
Substrates:Pressure sensitive coated papers, paper & board stocks.
Target Viscocity: 200-250 cps @25°CCure: 300 ft/minGloss: 90+ (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1015 Gloss Roller Coat ClearOP1015 has been developed for roller coat applications. This topcoat will exhibit excellent flow, leveling properties, resulting in high gloss cured films with excellent flexibility and rub/scuff resistance.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Target Viscocity: 120-240 cps @25°CCure: 300 - 600 watts per inchGloss: 80+ (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:Apply with a Roller Coater. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1016 UV GP Gloss OPVOP1016 is a solvent-free, UV curable general purpose coating. This product exhibits excellent adhesion to paper and some treated film stocks. It exhibits excellent flow, wet out, and leveling. It is recommended for use with solvent base, UV curable and water base inks to provide a good overall set of properties to labels at an economical Price. The product has good scuff, excellent chemical resistance, good water resistance, and a very high gloss.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 250-300 cps @25°CCure: 300-600 watts per inchGloss: 85+ (60°)Rub: 1000+ Sutherland Rubs (4lb Weight)Slide: <12° (face to face)Resistance: Solvent and WaterShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1027
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed
web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1017 UV Gloss IMP VarnishOP1017 is a solvent-free, UV curable stampable coating. This product exhibits excellent adhesion to paper and some treated film stocks. It exhibits excellent flow, wet out, and leveling. It is used to provide a stampable, low fingerprint coating over many water based, solvent based, and UV curable inks.
Substrates:Pressure sensitive coated papers, and treated films.
Target Viscocity: 230-300 cps @25°C/77°FCure: 300-600 watts per inchGloss: 85+ (60°)Rub: 1000+ Sutherland Rubs (4lb Weight)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
OP1021 UV Flexo DT OPVOP1021 is a solvent-free, UV topcoat designed specifically for use with direct thermal substrates. This product exhibits excellent adhesion to paper and most treated film stocks. It exhibits good flow, wet out, and leveling properties. The result is very high gloss with excellent adhesion, flexibility, and clarity. The product is durable and offers good chemical resistance.
Substrates:Pressure sensitive direct thermal coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 200 -225 cps @77°FCure: 300W/in Hg LampAppearance: Amber LiquidShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur.The product should be mixed prior to use.
OP1027 Premium Gloss OPVOP1027 Premium Gloss Over Print Varnish exhibits high gloss and is specifically formulated for Tag and Label printing. The overprint clear has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Target Viscocity: 300 -360 cps @25°CCure: 400 ft/min with one 300w/in lamp
Gloss: 90 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1027
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1028 Premium GlossHS OPVOP1028 is a high gloss UV coating. This product exhibits excellent adhesion to paper and some treated film stocks. It exhibits excellent flow, wet out, and leveling. It is recommended for use with solvent base, UV curable and water base inks to provide a good overall set of properties to labels at an economical Price. The product has good scuff, excellent chemical resistance, good water resistance, and a very high gloss.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks .
Target Viscocity: 240 - 290cps @25°CCure: 300-600 watts per inchGloss: >90 (60°)MEK: Excellent. 100 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1030 UV Gloss IMP Varnish IIOP1030 is a solvent-free, UV curable stampable coating. This product exhibits excellent adhesion to paper and treated film stocks. It exhibits excellent flow, wet out, and leveling. It is used to provide a stampable/imprintable coating over many water based, solvent based, and UV curable inks.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 150 - 190 cps @25°C/77°FCure: 300-600 watts per inchGloss: 90 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1030
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1031 UV Gloss TT Imprintable CoatingOP1031 is a UV curable coating that can be foil stamped, imprinted, laser printed or written on with most pens or markers. This product exhibits excellent flow, wet out, and leveling. It is used to provide a stampable/imprintable coating over many water based, solvent based, and UV curable inks.
Substrates:Most paper and and film based label substrates.
Target Viscocity: 190 - 230 cps @25°C/77°FCure: 200 ft/min with one 300w/in lampGloss: 90 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1032 UV Scuff Resistant Gloss BPFOPF1032 is a versatile, fast curing Benzophenone Free UV curable scuff resistant coating. This product exhibits excellent adhesion to paper and treated film stocks. It exhibits excellent flow, wet out, and leveling.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Target Viscocity: 390 - 370 cps @25°CGloss: 95 ± 4 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1103 UV Gloss Imprintable VarnishOP1103 UV Flexo Varnish exhibits outstanding product resistance to water, chemicals and a very high gloss. The OP1103 exhibits excellent flow, wet out, and leveling. Varnish has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 250 - 300 cps @25°C/77°FCure: 300W/in Hg lamp, 450+ fpmGloss: 85+ (60°)Rub: 1000+ (4lb weight)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1027
Application Suggestions:An anilox with a BCM range of 4.0 - 6.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of
friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP1107 UV Flexo HP Digital Resistance OP VarnishOP1107 UV Flexo HP Digital Resistant OP Varnish is specifically formulated for overprinting digitally printed Tag and Label applications. The overprint varnish exhibits high gloss and has excellent rheology characteristics making it ideal for most printing equipment.
Substrates:Digitally printed pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and board stocks.
Target Viscocity: 300 cps @25°C/77°FCure: 300W/in Hg lamp, 450+ fpmGloss: >80 (60°)Rub: >500 cycles (4lb weight, face to face)Slide: <12°MEK: >50 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF1107
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
OP2001 UV Matte VarnishOP2001 Matte UV Flexo Varnish was specifically formulated as a matte finish general purpose for Tag and Label printing. The overprint varnish has excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 750 cps @25°C/77°FCure: 300W/in Hg lampGloss: 8-12(60°)MEK: >100 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: OPF2001
Application Suggestions:An anilox with a BCM range of 5.0 – 8.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP2014 UV Matte Imprintable OPVOP2014 is a very versatile matte UV coating that offers a smooth low gloss finish, high scuff resistance, fast cure and can be foil stamped, imprinted or written on with a pen or marker. Specifically formulated for paper and film pressure sensitive materials for flexo label applications.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 250-290 cPs, #3 100rpm @25°C/77°FCure: 225 ft/min with one 300 watt/inch Hg lampGloss: <15 (60°)
Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP2015 UV Matte VarnishOP2015 UV Matte Varnish is a very versatile matte UV coating that offers a smooth low gloss finish, high scuff resistance and fast cure. The OP2015 UV MATTE VARNISH has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 300 - 360 cps @25°C/77°FCure: 300-600 W/in Hg lampGloss: <15 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not Available
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP2017 UV Scuff Resistant Matte BPFOPF2017 is a versatile, fast curing Benzophenone Free UV curable matte scuff resistant coating. This product exhibits excellent adhesion to paper and treated film stocks. It exhibits excellent flow, wet out, and leveling.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Target Viscocity: 275 - 425 cps @25°C/77°F Gloss: 13 ± 3 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP2018 UV Matte Imprintable VarnishOP2018 UV Matte Imprintable varnish is a very versatile matte UV coating that offers a smooth low gloss finish, high scuff resistance and fast cure. The OP2018 UV Matte Imprintable Varnish has excellent rheology characteristics, and press stability making it ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Cure: 300-600 W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not Available
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3000 UV Laminating AdhesiveOP3000 UV Laminating Adhesive was developed to bond clear films to various films, papers, and foil substrates. OP Series UV Flexo Adhesives are specifically formulated for Tag and Label printing. The laminating adhesives have excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board..
Target Viscocity: 750 cps @25°CCure: 300W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Application Suggestions:An anilox with a BCM range of 2.5 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3003 UV Release CoatingOP3003 UV Release Coating is designed to be used with most pressure sensitive adhesives for multi-layered construction of booklets, coupons and extended flap labels. The UV Release Coating has excellent rheology characteristics, and superior cure speed. OP3017 UV Flexo Peel & Release Adhesive can be used with the OP3003 to create a “Peel/Reseal” type of label where the label can be opened and resealed multiple times. OP3018 UV Flexo Dry Peel Adhesive can be used with the OP3003 to create a “Dry Peel” type label.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 630-780 cps @25°CCure: 300W/in Hg lampMEK: > 10 double rubsShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub
resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3015 Laminating AdhesiveOP3015 Laminating Adhesive was developed to bond clear films to various films, papers, and foil substrates. OP Series UV Flexo Adhesives are specifically formulated for Tag and Label printing. The laminating adhesives have excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 450 - 550 cps @25°CCure: 250 fpm with one 300W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
OP3016 Cold Foil AdhesiveOP3016 Cold Foil Adhesive is a non pressure-sensitive adhesive designed to be printed, wet laminated, and cured through special transparent cold foil films. Superior processing speeds and competitive material costs enable OP3016 to provide significant economic advantages over other cold foil adhesives or traditional hot foil die set-ups.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 290 - 370 cps @25°CCure: 300-600 W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3017 Peel & Release AdhesiveOP3017 UV Flexo Peel & Release Adhesive can be used with the OP3003 to create a “Peel/Reseal” type of label where the label can be opened and resealed multiple times.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 1600-2200 cps @25°CCure: 300W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 10 - 25 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3018 Dry Peel AdhesiveOP3018 UV Flexo Dry Peel Adhesive can be used with the OP3003 to create a “Dry Peel” type label.
Substrates:Pressure sensitive coated papers, vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and paper & board stocks.
Target Viscocity: 175-275 cps @25°CCure: 300W/in Hg lampShelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5 - 10 is suggested for flexo applications, with a reverse angle doc tor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP3020 Laminating AdhesiveOP3020 Laminating Adhesive was developed to bond clear films to various films, papers, and foil substrates. OP Series UV Flexo Adhesives are specifically formulated for Tag and Label printing. The laminating adhesives have excellent rheology characteristics making them ideal for most printing equipment, and product applications.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene, paper and board.
Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OP8003 R/S Gloss VarnishOP8003 Rotary Screen Gloss Varnish is formulated for roll label applications. The OP8003 exhibits exceptional print characteristics such as adhesion to a wide range of substrates, has a high gloss, and excellent abrasion resistance.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper and board.
Target Viscocity: 3000 - 4000 cps 3@50Cure: 300W/in Hg lamp
Gloss: 80+ (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is formulated with Benzophenone.BP Free Alternative: Not available
Application Suggestions:It is recommended that you use a screen that will apply an ink film thickness of 5-15 microns. This product is formulated to be press ready and can be printed over Nazdar® Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OPF1032 Scuff Resistant Gloss BP FreeOPF1032 is a versatile, fast curing Benzophenone Free UV curable scuff resistant coating. This product exhibits excellent adhesion to paper and treated film stocks. It exhibits excellent flow, wet out, and leveling.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Target Viscocity: 390 -370 cps @25oCGloss: 95 ± 4 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
OPF2017 Scuff Resistant Matte BPFOPF2017 is a versatile, fast curing Benzophenone Free UV curable matte scuff resistant coating. This product exhibits excellent adhesion to paper and treated film stocks. It exhibits excellent flow, wet out, and leveling.
Substrates:Pressure sensitive vinyl’s, top coated and print treated polyester, BOPP films, polyethylene, polystyrene and some paper & board.
Target Viscocity: 275-425 cps @25°CGloss: 13 ± 3 (60°)Shelf Life: 6 months (Unopened containers)Benzophenone (BP): This product is Not formulated with Benzophenone.
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored in a sealed container away from heat, flame and should not be exposed to any direct light source. Otherwise, premature cure or gel could occur. The product should be mixed prior to use.
UV - Varnishes/Adhesives
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Water Based - NARROW WEB INKS
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Water Based - Flexo
W100 Series Water Based Flexo Paper InkThe W100 Series Water Based Flexo Paper Ink is specifically formulated to meet the demands of today’s Narrow Web converters. The W100 Series Water Based Paper Ink features:• Ease of Use• High Speed Printing• Good Color Strength• Excellent Press Stability• Superior Resolubility
Substrates:Coated / Uncoated Paper.
Viscosity:On average 12 - 18 sec., #3 Zahn @ 77°F
pH Range:8.0 – 10.0
Plates:This ink Series is compatible with most WB Flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Safety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent). Wash the affected area with soap and water. Consult the W100 Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
Fade Resistance:This ink series is designed for interior applications only. Fade Resistant colors are not available in this Series. If fade resistance is required please contact your local Nazdar representative for an alternate product recommendation.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using anilox volume of 1.50– 2.50 BCM.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volume of 3.80 – 4.50 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per Container:Opaque White: 11 lb, 50 lb, 500lbBase Transparent White: 8 lb, 40 lb, 400lbOther Colors: 9 lb, 45 lb, 450lb
Stock No. Base Printing Colors
W100308 Opaque White
W100309 Black
W100010 Transparent White
W100311 Yellow
W100312 Orange
W100313 Warm Red
W100314 Rubine Red
W100315 Rhodamine Red
W100316 Purple
W100317 Violet
W100318 Reflex Blue
W100319 Process Blue
W100320 Green
Stock No. Process Colors
W100061 Process Yellow
W100062 Process Magenta
W100063 Process Cyan
W100064 Process Black
Stock No. Additives
CARE79 pH Adjuster
CARE75 Defoamer
RE192 Retarder (Slow Additive)
Stock No. Cleaner
NWC10 EZ Cleaner
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
W330 Series Water Based Flexo InkThe W330 Series Water Based Film Ink is specifically formulated to meet the demands of today’s Narrow Web Label converters. The W330 Series Water-Base Film Ink features:• Superb Resolubility• Low Viscosity• High Color Strength• Compatible with Water-based and UV Coatings• Fast Drying• Excellent Press Stability
Substrates:Coated/uncoated paper and various print treated films.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity, See the additive guide.
Clean Up: Use NWC10 EZ Cleaner.
Storage and Handling:Thoroughly mix the ink prior to printing.Maintain ink temperature between 65°F - 90°F (18°C - 32°C) for optimum print and performance. Proper personal protection equipment is required when handling this material. Please consult SDS for details on proper handling of this material.
Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.Containers should be sealed tightly after use.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Fade Resistance:Inks are formulated with standard and fade resistant (FR) pigments.
PRODUCT OFFERINGProcess Colors:Process colors are formulated to print using an anilox volume of 1.0 -2.0 BCM.
Base Colors:Base colors are designed to print using aniloxvolume of 3.0 – 4.0 BCM.Base colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per ContainerOpaque White 11 lb, 50 lbTransparent White / Extender 8 lb, 40 lbOther Colors 9 lb, 45 lb
Base Colors Stock No.
Black W330309
Transparent White W330010
Yellow W330311
Orange W330312
Warm Red W330313
Rubine Red W330314
Rhodamine Red W330315
Purple W330316
Violet W330317
Reflex Blue W330318
FR Process Blue (BW8) W330319
FR Green (BW8) W330320
Fade Resistant Colors Stock No.
FR Yellow W330321
FR Warm Red W330323
FR Rubine Red W330324
FR Rhodamine Red W330325
FR Purple W330326
FR Violet W330327
FR Reflex Blue W330328
Process Colors Stock No.
Process Yellow W330061
Process Magenta W330062
Process Cyan W330063
Process/Dense Black W330064
Other Colors Stock No.
Opaque White W330308
Dense Black W330379
Back Side Black (4BCM) W330450
Additives Stock No.
PH Adjuster CARE79
Additives are typically not needed, please only use as directed by Nazdar. For more details please refer to the Flexo Additive Guide.
Cleaner Stock No.
Slow Reducer NWC10
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
W510 Series Water Based Flexo InkW510 Series Water Based Flexo Inks have been formulated to meet the needs of SHRINK SLEEVE and LAMINATION applications. With superb press stability, high run speeds, and excellent color strength this ink system is sure to meet the needs of today’s flexographic printers. W510 Series Water Based Flexo Inks perform well in both inline and offline lamination applications with various adhesive chemistries. W510 Series Water Based Flexo Inks can also be used for “Reverse Print” Shrink Sleeves when combined with our high slip opaque white inks.
Substrates:PVC and PETNote: As with all film substrates, lots may vary and testing is recommended before use
Anilox Rolls: For standard colors use an anilox with a cell volume of 3.0 bcm - 5.0 BCM. For process colors use an anilox with a cell volume of 1.0 – 2.0 BCM.
Viscosity:On average 14-25 sec., #3 Zahn @ 77°F
pH Range:9.0 – 10.0
Plates:This ink Series is compatible with most water based flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity. See the additive guide.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Safety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the Ink Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
Fade Resistance:This ink series is designed for interior applications only. The colors designated with (FR) are formulated with pigments which have extended fade resistance.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using 1.0 - 2.0 BCM aniloxes.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volume of 2.5 – 3.5 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per Container:Opaque White: 11 lb, 50 lb, 500lbBase Transparent White: 8 lb, 40 lb, 400lbOther Colors: 9 lb, 45 lbOverprint Varnish: 8 lb, 40 lb, 450lb
Stock No. Standard Colors BW
W510309 Base Black 8
W510010 Transparent White -
W510311 Base Yellow 5
W510312 Base Orange 6
W510313 Base Warm Red 5
W510314 Base Rubine Red 4
W510315 Base Rhodamine Red 3
W510316 Base Purple 3
W510317 Base Violet 4
W510318 Base Reflex Blue 4
W510319 FR Process Blue 8
W510320 FR Green 8
W510379 Dense Black 8
Stock No. Fade Resistant Colors BW
W510321 FR Yellow 6
W510322 FR Orange 6
W510323 FR Warm Red 6
W510324 FR Rubine Red 6
W510325 FR Rhodamine Red 8
W510326 FR Purple 8
W510327 FR Violet 8
W510328 FR Reflex Blue 8
Stock No. Process Colors BW
W510041 Process Yellow 5
W510042 Process Magenta 4
W510051 FR Process Yellow 6
W510052 FR Process Magenta 6
W510053 FR Process Cyan 8
Water Based - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
W510054 FR Process Black 8
W510061 Process Yellow 5
W510062 Process Magenta 4
W510063 FR Process Yellow 6
W510064 FR Process Magenta 6
W510090 Process Extender -
Stock No. Opaque Whites
60050954W5 WB Opaque White Low slip.
60051724W5 WB Opaque White II High slip.
60018945W5 Shrink OP White
NW16124 TNV Opaque White
Stock No. Additives
CARE73 Stabilizer
CARE74 PH Adjuster
CARE75 Defoamer
RE198 Slow Reducer
CARE95 Slip Additive
Stock No. Cleaner
NWC10 EZ Cleaner
W770 Series Water Based Flexo InkThe W770 Series Water Based Flexo Inks exhibit outstanding pressroom performance and stability.Formulated to have excellent water resistance. These inks are high strength and low viscosity.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, coated paper and board. As with all film substrates, lots may vary, and testing is recommended before use.
Viscosity:On average 10-20 sec, #3 Zahn @ 77ºF
pH Range:8.5 – 10.0
Plates:This ink Series is compatible with most WB Flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity, See the additive guide.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°-32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:afety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the Ink Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:Testing should be conducted at least 4 hours after printing to allow the properties of the ink to fully develop. After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
Fade Resistance:This ink series is designed for interior applications only. The colors designated with (FR) use pigments which have extended fade resistance.
PRODUCT OFFERINGProcess ColorsStandard process colors are formulated to print using anilox volumes of 2.00 – 3.00 BCM.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volumes of 3.00 – 4.00 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Standard Colors Stock No.
Opaque White W770308
Base Black W770309
Transparent White W770010
Base Yellow W770311
Base Orange W770312
Base Warm Red W770313
Base Rubine W770314
Base Rhodamine W770315
Base Purple W770316
Base Violet W770317
Base Reflex Blue W770318
Base Process Blue W770319
Base Green W770320
Process Colors Stock No.
Process Yellow W770041
Process Magenta W770042
FR Process Yellow W770051
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
FR Process Magenta W770052
Process Cyan W770053
Process Black W770054
Process Extender W770090
Fade Resistant Colors Stock No.
FR Warm Red W770323
FR Rubine Red W770324
FR Rhodamine Red W770325
FR Purple W770326
FR Violet W770327
FR Reflex Blue W770328
Additives Stock No.
PH Adjuster CARE79
Cleaner Stock No.
EZ Cleaner NWC10
W750 Series Water Based Polycoated Board InkThe W750 Series Water Based Polycoated Board Inks are developed for use on disposable beverage cups, cartons and containers manufactured from polycoated board. These inks have been specifically developed to have excellent water resistance and are ideal for use on cold cup and ice-cream containers. The W750 Series Water Based Cold Cup Inks exhibit outstanding pressroom performance and stability. These inks are high strength and low viscosity.
Substrates:Polycoated board.
Viscosity:On average 10-20 sec, #3 Zahn @ 77°F
pH Range:8.5 – 10.0
Plates:This ink Series is compatible with most WB Flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity, See the additive guide.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Safety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the Ink Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:Testing should be conducted at least 4 hours after printingto allow the properties of the ink to fully develop. After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
Fade Resistance:This ink series is designed for interior applications only. The colors designated with (FR) use pigments which have extended fade resistance.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using aniloxvolumes of 2.00 – 3.00 BCM.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volumes of 4.00 – 6.00 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per Container:Opaque White 11 lb, 50 lbBase Transparent White 8 lb, 40 lbOther Colors 9 lb, 45 lb
Base Printing Colors Stock No.
Black W750309
Transparent White W750010
Yellow W750311
Orange W750312
Warm Red W750313
Rubine Red W750314
Rhodamine Red W750315
Purple W750316
Violet W750317
Reflex Blue W750318
Fade Resistant Printing Colors Stock No.
FR Process Blue W750319
Water Based - Flexo
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
FR Green W750320
FR Yellow W750321
FR Warm Red W750323
FR Rubine Red W750324
FR Rhodamine Red W750325
FR Purple W750326
FR Violet W750327
FR Reflex Blue W750328
Process Colors Stock No.
Process Yellow W750041
Process Magenta W750042
FR Process Yellow W750051
FR Process Magenta W750052
FR Process Cyan W750053
FR Process Black W750054
Additives Stock No.
PH Adjuster CARE79
Defoamer CARE75
Cleaner Stock No.
EZ Cleaner NWC10
W751 Series Water Based InkThe W751 Series Water Based Inks are developed for useon disposable beverage cups, cartons and containersmanufactured from polycoated board.These inks have been specifically developed to haveexcellent water resistance.The W751 Series Water Based Cold Inks exhibit outstandingpressroom performance and stability. These inks are highstrength and low viscosity.
Substrates:Polycoated board.
Viscosity:On average 10-20 sec, #3 Zahn @ 77°F
pH Range:8.5 – 10.0
Plates:This ink Series is compatible with most WB Flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing. The pH and viscosity of the ink should be maintained during printing with the use of additives to adjust pH and viscosity, See the additive guide.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Safety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the Ink Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:Testing should be conducted at least 4 hours after printingto allow the properties of the ink to fully develop. After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
Fade Resistance:This ink series is designed for interior applications only. The colors designated with (FR) use pigments which have extended fade resistance.
PRODUCT OFFERINGProcess Colors:Standard process colors are formulated to print using aniloxvolumes of 1.00 – 2 .00 BCM.
Base Colors:Standard base colors are designed to be high strength, and formulated to print using anilox volumes of 3.00 – 4.00 BCM. The colors can be mixed together to achieve an unlimited number of strong vibrant colors.
Packaging Per Container:Opaque White 11 lb, 50 lbBase Transparent White 8 lb, 40 lbOther Colors 9 lb, 45 lb
Base Printing Colors Stock No.
Black W751309
Transparent White W751010
Yellow W751311
Orange W751312
Warm Red W751313
Rubine Red W751314
Rhodamine Red W751315
Purple W751316
Violet W751317
Reflex Blue W751318
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Fade Resistant Printing Colors Stock No.
FR Process Blue W751319
FR Green W751320
FR Yellow W751321
FR Warm Red W751323
FR Rubine Red W751324
FR Rhodamine Red W751325
FR Purple W751326
FR Violet W751327
FR Reflex Blue W751328
Process Colors Stock No.
Process Yellow W751041
Process Magenta W751042
Process Cyan W751043
Process Black W751044
Process Extender W751090
Additives Stock No.
PH Adjuster CARE79
Slow Reducer CARE119
Cleaner Stock No.
EZ Cleaner NWC10
WM Series Water Based Metallic InksThe WM series is a Metallic Ink system that uses the latest in Water-base technology. The WM series utilizes pigment and binder technology that will exhibit a brilliant metallic effect.
Substrates:Paper, Paperboard, and various films.
Film Weight: Recommend coat weight: 0.6-1.0 wet pounds per 1000 square feet.
Viscosity:On average 18-25 sec., #3 Zahn @ 76°F
pH Range:7.0 – 8.2
Plates:This ink Series is compatible with most WB Flexo plates on the market.
Printing:This ink series is formulated to be press ready. Thoroughly mix the ink prior to printing.
Clean Up: Use NWC10 EZ Cleaner
Storage:Store tightly covered at temperatures between 65°-90°F (18°- 32°C). Ink taken from the press should not be returned to the original container; store separately to avoid contaminating unused ink.
Ink Handling:Safety glasses and gloves are suggested in areas where product may be splashed. If product does come in contact with skin, wipe ink off with a clean, dry cloth (do not use solvent or reducer). Wash the affected area with soap and water. Consult the Ink Series Material Safety Data Sheet for further instructions and warnings.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance and gloss. These tests should be performed prior to beginning the full production run.
PRODUCT OFFERING
Stock No. Metalliic Printing Colors
60010871WM W/B Laminating Silver
60028881WM W/B Shrink P-873 Gold
60031486WM W/B Shrink 877 Silver
60031487WM W/B AP 871 Gold
60031488WM W/B AP 872 Gold
60031489WM W/B AP 873 Gold
60031490WM W/B AP 874 Gold
60031491WM W/B AP 875 Gold
60031492WM W/B AP 876 Gold
697402WM WM 871 Gold
697403WM WM 872 Gold
697404WM WM 873 Gold
697405WM WM 874 Gold
697406WM WM 875 Gold
697407WM WM 876 Bronze
697409WM WM Bright Silver 40#
Stock No. Extenders & Cleaners
697408WM WM Metallic Extender
NWC10 EZ Cleaner
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
WV1000 WB GP Gloss CoatingWV1000 is a general purpose high gloss water based coating formulated for application via flexo presses.
Substrates:Paper and board stocks and some Films.
Target Viscocity: 18 - 20 sec. /#3 Zahn @ 25°CGloss: ~70 (60°)Rub: 500 Sutherland Rubs (4lb weight, face to face)pH: 8.0 - 9.0VOC: 0.7%Solids: 33-37%Other: FDA: Dry Film-21 CFR: 175.170, 176.170 (with Limits), and 176.180Drying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV1100 WB Heat Resistant Lidding CoatingWV1100 WB HR Lidding Coating is formulated for heat seal applications for Tag and Label printing. This coating is ideal where high heat resistance is needed. This ink is a water based flexo ink designed specifically for lids. This product has excellent rheology characteristics making it ideal for most printing equipment, and product applications.
Substrates:Paper, paperboard and foil stocks.
Target Viscocity: 16 -20 sec. /#3 Zahn @ 25°CGloss: ~63 (60°)
Rub: 250 Sutherland Rubs (4lb weight, face to face)pH: 8.5 -9.5Other: Heat Resistance: 375F @ 70psi for 1.5 secDrying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV Series WV1105 W/B ROP-DE CTGWV1105 ROP-DE Coating was developed for Moisture Res, Thermal Transfer Ribbons (Wax/Resin), Direct Thermal, and High Rub properties.
Substrates:Paper stock and Films
Target Viscocity: 125-30sec/#2 Zahn @ 70°FResistance: Water and AlkalipH: 8.5-9.5VOC: <0.05Solids: 37% ±1%Other: FDA: Dry Film-21 CFR: 175.170, 176.170 (with Limits), and 176.180Drying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:It is recommended that you use an Anilox that will apply a wet ink film weight of 0.8-1.2 lbs/MSF to optimize coating performance. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Water Based - Coatings/Adhesives
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV1107 WB Shrink Sleeve Adhesive CoatingWV1107 is a Water based dispersion of high molecular polymers. WV1107 has a medium viscosity. WV1107 is suggested for use as a heat seal coating for bonding films, aluminum foil and paper to various substrates. The WV1107 is also used as a spot adhesive in Shrink Sleeve applications. FDA Status: This product meets the requirements of 21CFR 175.105.
Substrates:Paper stock and Films.
Target Viscocity: 750 cps @ 77oF (only add water to reduce viscosity)pH: 9.5-10.0 (do not adjust pH)Solids: 37%Other: Minimum heat activation range is 160° - 250°FDrying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:It is recommended that you use an Anilox that will apply a dry coating weight 2-7 lbs 3000 sq. ft. to optimize coating performance. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
Water Based - Coatings/Adhesives
WV1111 W/B PrimerWV1111 WB Primer is formulated for application via Flexo presses. When fully dried this primer exhibits good imprintability with good rub resistance.
Substrates:Paper and Paperboards.
Target Viscocity: 18 - 22 sec/#3 Zahn @ 72°FDrying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV1113 WB HR CoatingWV1113 WB HR Coating is formulated for flexo applications where a Heat Resistant, gloss, fast drying and block resistant coating is needed.
Substrates:Paper, Board and some flexible films.
Target Viscocity: 20 - 24 sec/#3 Zahn @ 72°FGloss: 64±3(60°)Rub: 250 cycles face to face with 4# weightResistance: Heat Resistant - 40psi / 1sec @ 400°FVOC: 0.18 (lb/gal)Solids: 37%±1%Other: Block Resistance face to face 2psi / 16HRS @ 120°F.Drying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV Series WV1114 WB FDA Gloss CoatingWV1114 is formulated for flexo applications where good gloss, fast drying, block resistance, low odor, water resistance is needed.This product is cleared for use in accordance with 21 C.F.R.175.105 and 176.180. And under certain conditions with 176.170. Please contact Nazdar for specifics
Substrates:Plastic, Paper and Paperboard.
Target Viscocity: 17 - 21 sec/#2 Zahn @ 76°FGloss: 71±2(60°)Rub: 500 cycles face to face with 4# weight VOC: 1.8%Solids: 37% ±1%Other: Block Resistance face to face 2psi/16HRS @120°F. Complete releaseDrying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
WV Series WV2002 WB Matte Imprintable CoatingWV2002 is a water based imprintable matte coating formulated for application via flexo presses.
Substrates:Pressure sensitive vinyl, top coated and print treated polyester, BOPP films, polyethylene, polystyrene, paper and board.
Target Viscocity: 19-23 sec/#3 Zahn @ 76°FGloss: ~9 (60°)Rub: 100 rubs with 4lb weightDrying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner or suitable solvent.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
WV Series WV3000 WB Heat Seal AdhesiveWV3000 is a heat sealable coating for blister pack applications. This adhesive has a sealing range of 350 - 450°F. It features fast drying, good gloss and wetting over other inks.
Substrates:PVC and PETG films, paper and board stocks.
Target Viscocity: 19 - 22 sec/#3 Zahn @ 76°FpH: ~8.0 - 9.0VOC: 13.3%Drying: Sufficient volumes of warm air, medium or short wave I.R.Shelf Life: 6 months (Unopened containers)
Application Suggestions:An anilox with a BCM range of 5.0 - 10.0 is suggested for flexo applications, with a reverse angle doctor blade. This product is formulated to be press ready and can be printed over Nazdar Rotary Screen, UV Flexo and Water Base Flexo inks.
Performance Verification:After press/job set up is complete, inspect a portion of the printed web for all applicable and specified properties. These properties include but are not limited to: cure, adhesion, mar and rub resistance, product resistance, gloss, and coefficient of friction. These tests should be performed prior to beginning the full production run.
Clean Up:Use NWC10 EZ Cleaner.
Storage and Handling:Proper personal protection equipment and adequate ventilation are required when handling this material. Please consult MSDS for details on proper handling of this material. This product should be stored tightly covered at temperatures between 65°- 90°F (18°- 32°C). The product should be mixed prior to use.
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Index6400 Series UV Flexo Ink ................................................................................216800 Series UV LED Flexo Ink ...................................................................... 66800 Series UV LED Flexo Metallic Ink ................................................. 868NC Series Nestlé Compliant UV LED Flexo Ink ........................ 77400 Series UV Flexo Ink ................................................................................228300 Series UV Rotary Screen Ink .........................................................19 8700 Series UV LED Rotary Screen Ink ................................................ 992NCF Series UV Flexo Ink ...........................................................................149300 Series UV Flexo Ink ................................................................................159400 Series UV Flexo Ink ................................................................................17
FFlexo - UV Inks ..........................................................................................................14 Flexo - UV LED Inks ................................................................................................ 6Flexo - Water Based Inks ..................................................................................38
IInk Answers ..................................................................................................................... 4
LLetterpress UV Inks ...............................................................................................21
OOffset UV Inks ............................................................................................................21OP1001 UV Flexo GP Varnish AF ...........................................................23OP1003 UV GP Varnish AF ...........................................................................23OP1005 UV GP Gloss Varnish ....................................................................23OP1007 UV Gloss Resist Varnish .............................................................24OP1008 UV Gloss Resist II Varnish ........................................................24OP1009 UV Gloss Resist Varnish ............................................................24OP1010 UV Gloss Flexo Varnish ..............................................................25OP1011 UV Gloss Flexo Varnish 722 ...................................................25OP1012 UV Gloss M Varnish .......................................................................26OP1013 Combo Screen/Coater TC .......................................................26OP1015 Gloss Roller Coat Clear ..............................................................26OP1016 UV GP Gloss OPV ..........................................................................27OP1017 UV Gloss IMP Varnish ..................................................................27OP1021 UV Flexo DT OPV ............................................................................28OP1027 Premium Gloss OPV ......................................................................29OP1028 Premium Gloss HS OPV ............................................................29OP1030 UV Gloss IMP Varnish II .............................................................29OP1031 UV Gloss TT Imprintable Coating .......................................29OP1032 UV Scuff Resistant Gloss BPF ............................................29OP1103 UV Gloss Imprintable Varnish ................................................30OP1107 UV Flexo HP Digital Resistance OP Varnish ............30OP2001 UV Matte Varnish .............................................................................31OP2014 UV Matte Imprintable OPV .......................................................31OP2015 UV Matte Varnish .............................................................................31OP2017 UV Scuff Resistant Matte BPF ............................................32OP2018 UV Matte Imprintable Varnish ................................................32OP3000 UV Laminating Adhesive ...........................................................32OP3003 UV Release Coating ......................................................................33
OP3015 Laminating Adhesive .....................................................................33OP3016 Cold Foil Adhesive ..........................................................................34OP3017 Peel & Release Adhesive ..........................................................34OP3018 Dry Peel Adhesive ...........................................................................34OP3020 Laminating Adhesive .....................................................................35OP61003 UV LED Gloss Varnish .............................................................10OP61004 UV LED Gloss Imprintable Varnish ................................10OP62001 UV LED Matte Varnish .............................................................10OP63000 UV LED Laminating Adhesive ...........................................11OP63016 UV LED Cold Foil Adhesive .................................................11OP69001 UV LED Release Varnish .......................................................12OP8003 R/S Gloss Varnish ...........................................................................35OPF1032 Scuff Resistant Gloss BP Free .........................................35OPF2017 Scuff Resistant Matte BPF ..................................................36
RRotary Screen - UV Inks ....................................................................................15Rotary Screen - UV LED Inks .......................................................................... 9
UUV Flexo Polar White Ink ..................................................................................16UV Flexo Metallic Ink ............................................................................................18UV Inks .............................................................................................................................13UV Rotary Screen ....................................................................................................19UV Varnishes & Adhesives ..............................................................................23UV LED Inks ................................................................................................................... 5UV LED Varnishes & Adhesives ..................................................................10UV Letterpress ...........................................................................................................21
WW100 Series Water Based Flexo Paper Ink .....................................38W330 Series Water Based Flexo Ink .....................................................39W510 Series Water Based Flexo Ink .....................................................40W770 Series Water Based Ink .....................................................................41W750 Series Water Based Polycoated Board Ink .......................42W751 Series Water Based Ink .....................................................................43Water Based inks .....................................................................................................37Water Based Coatings & Adhesives ........................................................45WM Series Water Based Metallic Inks ...................................................44WV1000 WB GP Gloss Coating ................................................................45 WV1100 WB Heat Resistant Lidding Coating ...............................45WV Series WV1105 W/B ROP-DE CTG ...........................................45WV1107 WB Shrink Sleeve Adhesive Coating ..............................46WV1111 W/B Primer ..........................................................................................46WV1113 WB HR Coating ................................................................................46WV Series WV1114 WB FDA Gloss Coating .................................47WV Series WV2002 WB Matte Imprintable Coating .................47WV Series WV3000 WB Heat Seal Adhesive ................................48
An Ink That’s Right For Every Job. U.S.A. Phone: 1-800-767-9942www.Nazdar.com/NarrowWebCustomer Service E-mail: [email protected]
Notes:
U.S. Phone: +1-913-442-1888 U.K. Phone: +44-161-442-2111 Mexico Phone: +52 (55) 4777 1900 Technical Assistance E-mail: [email protected]
Notes:
Customer Service E-mail: [email protected] [email protected] today
Nazdar Ink Technologies -World Headquarters8501 Hedge Lane TerraceShawnee, KS 66227-3290 USAToll Free US: 866-340-3579Tel: +1 913-422-1888 E-mail: [email protected] Support E-mail: [email protected]
Nazdar – EMEANazdar House, Battersea RoadHeaton Mersey Industrial EstateStockport, Chesire SK4 3EA United KingdomTel: + 44 (0)-161-442-2111EMEA Technical Service E-mail: [email protected]
Nazdar – Asia Pacific11, Changi North Street 1 #03-03/04Singapore 498823Tel: +65-63854611E-mail: [email protected]
Nazdar – TlalnepantlaGustavo Baz 180 D-4San Jeronimo Tepetlacalco Tlalnepantla, Edo. de Mexico 54090 Mexico Tel: +52 (55) 4777 1900Fax: +52 (55) 5362 7282
Nazdar.com
NARROW WEB PRINTING INKS
Nazdar.com
Distributor:
LIT0700 0519
Got ink questionsWe have ink answers.
An Ink That’s Right For Every Job.