Naomi Home Tufted Futon Assembly Instructions copy · E F Wood Dowel Pin G x 1 Allen Wrench 1. Arm...

Assembly Instructions

Product Dimensions:82” L x 35” D x 32” H

Please take a moment to read through the entire instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions step by step and this should make this process as easy as we could make it for you.

If you need help or have damaged or missing parts, contact customer service at www.NaomiHome.com.

of 8

N A O M I

Convertible Tufted Futon

H O M E

© 2018 Naomi Home, Inc. - All Rights Reserved.

Insert Completed Product Line ArtLines min 0.75 - 1.0pt weight

Tools Required

Phillips Screwdriver(Medium)

ADULT ASSEMBLY REQUIREDCHOKING HAZARD• This product includes small parts, sharp points and sharp edges in its unassembled

state. Keep unassembled parts away from children under 3 years of age, & animals.• If used improperly, your doll bunk bed may be pulled over or fall, creating risk of injury or damage. Children should not be permitted to climb or pull on the Futon.

USE AND MAINTENANCE

• Use on level surfaces only• Because this product needs assembly, it is prone to working itself loose from time to time depending on the use. Please take the time to check that all connections are still tight and working properly for safety.• Only clean using a damp cloth and mild detergent, do not use bleach or abrasive cleaners.

PARENTAL SUPERVISION IS REQUIRED• This Naomi Kids product is intended for child use age 3+.• Parents or Guardians should supervise use under the intended age specifically regarding children that may have access to it and might climb on the unit.

ASSEMBLY RECOMMENDATIONS• Check you have all the components and tools listed on page 2 and 3.• Do not stand or put weight on this product during assembly, this could cause damage.• Remove all hardware from the plastic bags and separate them into their groups.• Assemble the item as close to its final position (in the same room) as possible.• Assemble on a soft level surface to avoid damaging the unit or your floor.• Make sure you have enough space to layout the parts before starting.• Parts of the assembly may be easier with 2 people.• Dispose of all packaging carefully and responsibly.• Do not use this item if any components are missing or damaged.• We do not recommend the use of power drill/drivers for inserting screws, as this could damage the unit. Only use hand screwdrivers.

WARNING CAUTION

Allen Wrench(included)

of 8

This drawing is to give you an overall idea only of how this assembly will go together and does not replace the assembly instructions.

Please take a moment to read through the whole instruction booklet before assembly to familiarize yourself with this product . Once you feel ready to start, follow the instructions step by step and this should mak e this process as easy as we could make it for you.

Due to the number of parts involvedassembly can take a few hours so set aside between 30 minutes and 1 hour to assemble thiswithout rushing.

ASSEMBLY AT A GLANCE

of 8

COMPONENT PARTS

Please check that you have all the parts listed below

Boltx 2 x 2

ASSEMBLY HARDWARE

FE Wood Dowel Pin Gx 1

Allen Wrench

1. Arm (seated Right) x12. Futon Body x13. Arm (seated Left) x14. Front Outer Leg x25. Center Leg x26. Rear Outer Leg x2

Metal Mount Bracketx 2

Fabric Protectorx 2

BA Washer Cx 6 x 8

ScrewD

of 8

1 32

4 5 6

ASSEMBLY INSTRUCTIONS

2

1

Select 2, 4 x2, 5 x2, 6 x2, C x6, D x8. Turn Futon Assembly unside down on a soft surface to not scratch the material. Insert the post of 4 into C fabric protector and assemble to front left hole by turning clockwise until hand snug. Repeat for other 4 leg into front right hole. Select 5 x2, place C over post of 5 x2 and screw one leg into front center hole. Repeat for back center hole. Place C fabric protection x2 over area for 6 in rear corners with 4 D Screws attach 6 to 2. Repeat for other 6 leg.

of 8

2

Select A x2, on left (seated) end of futon sofa assembly attach A mount bracket using E bolt x2. Repeat for 2nd A bracket on other end.

5

6 65

44

5D

2

AE

ASSEMBLY INSTRUCTIONS

4

3

Select 1, 3. Align mount brackets on 1 to Right (seated) end of Futon Sofa 2. Slide both metal brackets on 1 into the brackets on 2 until snug. Lift slightly to see if aligned correctly. Repeat for 3 to sofa 2.

Congratulations Your Naomi Home Tufted Futon is complete.

Operating: Raise back rests into full upright position. To lower back rests pull forward 1 side until hardware clicks and releases. Repeat for other back rest.

of 8

2

1 3

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

6

5

Lower backrests completely �at for bed.

To recline back rests to your desired angle always pull backrest all the way for-ward for it to release, then return to �at sleeping posi-tion. Then pull backrest again forward to desired recline position. of 8

ASSEMBLY COMPLETE

of 8

www.NaomiHome.comMADE IN CHINA

Product Packaging Information

Model #:

Color:

Shipment Ref. #:

Date:

________________________________

__________________________________

_________________________

__________________________________

ENJOY YOUR NEWNAOMI HOME CONVERTIBLE TUFTED FUTON!

N A O M IH O M E

Naomi Home Tufted Futon Assembly Instructions copy · E F Wood Dowel Pin G x 1 Allen Wrench 1. Arm...

Documents

Transcript of Naomi Home Tufted Futon Assembly Instructions copy · E F Wood Dowel Pin G x 1 Allen Wrench 1. Arm...