My Ceros Download - Kelly Roofing€¦ · 800-248-0280 EXCEPTIONAL Metals, a division of...

INDEXIntroduction ..........................................3

Testing Requirements ............................4

Testing Definitions ..................................5

Recommended Tools ..............................8

Common Industry Terms ........................9

Duro-Guard® Edge System ................13

Fascia Cover ........................................14

4” Flex Fascia Cover ............................15

2-Piece Snap-On Compression ............16

2-Piece Flex Snap-On Compression ....17

Snap-On Fascia Base ..........................18

Gravel Stop Covers ..............................19

Edge Extender ......................................20

Scuppers/Pitch Pans ..........................21

Single Skirt Scupper..............................22

Double Skirt Scupper ............................23

Scupper with Decorative

Metal Flange ........................................24

Spill-Out Scupper ..................................25

Vinyl-Coated Pitch Pan ........................26

Collectors/Conductors........................27

Vinyl-Back Collector ..............................28

Conductor..............................................29

Gutters/Downspouts ..........................30

EX-Style, E-Style Gutters ......................32

MX-Style, M-Style Gutters ....................33

DX-Style, D-Style Gutters ....................34

LX-Style, L-Style Gutters ......................35

Removable Gutter System ....................36

Gutter Accessories ................................37

Downspouts ..........................................38

Customized Downspout Assembly........39

Drainage Accessories ..........................40

Coping Systems ..................................41

Snap Coping ........................................42

Canted Coping ......................................43

Flat Coping............................................44

Vinyl-Coated Products........................45

T-Edge ..................................................46

T-Edge Plus ..........................................47

Vinyl-Coated Drip Edge ........................48

Vinyl-Coated Snow Diverter and

Snow Guard ..........................................49

Custom Fabrication ............................50

1-Piece Reglet ......................................51

2-Piece Reglet ......................................52

Duro-Flash II ........................................53

Custom Cornice Flashing......................54

Standing Seam Panels........................55

Details ..................................................56

Detail 2060 Metal Flange and

Double Skirt Scupper ............................57

Detail 2061 Single Skirt

Metal Scupper ......................................58

Detail 2070 Vinyl Back Collector

with Scupper ........................................59

Detail 2071 Flanged Scupper

with Conductor ......................................60

Detail 2080 Metal Downspouts ............61

Detail 2085 Metal Downspout

Elbows ..................................................62

Detail 2086 Square-To-Round

Adapter..................................................63

Detail 2090 Gutter Attachment ..............64

Detail 2091 Gutter Attachment

X-Series ................................................65

Detail 2095 Gutter Expansion

Joint ......................................................66

Detail 2100 Removable Gutter

System – Opt 1 ....................................67

Detail 2105 Removable Gutter

System Opt 2 ........................................68

Detail 3020 Standard T-Bar

into Gutter ............................................69

Detail 3025 X-Series T-Bar

into Gutter ............................................70

Detail 3110 2-Piece Compression

Edge......................................................71

Detail 3120 Vinyl Coated Metal

Drip Edge ..............................................72

Detail 3500 1-3/4” Metal Fascia

System ..................................................73

Detail 3510 4” Metal Fascia

System ..................................................74

Detail 3511 4” Metal Flex Fascia

Cover ....................................................75

Detail 3513 2-Piece Flex Snap-On

Compression ........................................76

Detail 3520 2” Metal Gravel Stop

Cover ....................................................77

Detail 3530 4” Metal Gravel Stop

Cover ....................................................78

Detail 3540 Edge Extender ..................79

Detail 3550 T-Edge................................80

Detail 3555 T-Edge Plus........................81

Detail 3560 Fascia Base ......................82

Detail 3570 Spill-Out Scupper ..............83

Detail 4045 Vinyl Coated Pitch Pan ......84

Installation 6050 Flat Coping ................85

Detail 6050 Flat Coping ........................86

Installation 6052 Canted Coping ..........87

Detail 6052 Canted Coping ..................88

Detail 6054 Snap Coping ......................89

Installation 1 6054 Snap Coping ..........90

Installation 2 6054 Snap Coping ..........91

Detail 6130 1-Piece Reglet ..................92

Detail 6140 Duro-Flash ........................93

Detail 6145 2-Piece Reglet ..................94

2

800-248-0280www.exceptionalmetals.com

EXCEPTIONAL Metals, a division of Duro-Last® Roofing, Inc.,

offers a complete line of metal roofing products and accessories

to finish any roofing project.

EXCEPTIONAL Metals Offers Your Customers:

• One single-source for prefabricated roofing and metal edge products.

• Edge-to-edge warranty protection that guarantees the watertight integrity

of the roofs.

• Quick order fulfillment. Most products are ready-to-ship within five

business days.

• Access to skilled staff that can design and fabricate custom pieces and

vinyl-coated metals.

Need one custom item or 100 custom items?

If you can draw it, we can make it!

Our highly-skilled staff can craft custom items in 25 stocked finishes

as well as these specialized metals:

• .040 Aluminum with Kynar® finish.

• .040 and .050 Aluminim with mill finish.

• 16-oz. Copper.

• 24-gauge Stainless Steel.

• 24-gauge Bonderized (Paintable) Steel.

• Galvalume® Plus

3 Introduction

EXCEPTIONAL Metals Products Meet ANSI/SPRI ES-1

2003 Method RE-2 Testing Requirements

TAS 111.95 Test Results

* O.C. = On-Center


12-Piece Base (#2600B) with

Cover (#2600T)4˝ 6˝ O.C.* 280 lbs/ft² 1-360

22-Piece Base (#2602B) with

Cover (#2602T)6˝ 6˝ O.C.* 130 lbs/ft² 1-135

3Fascia Bar (#1568) with Metal

Fascia Cover (#2537)13⁄4˝ 6˝ O.C.* 1,160 lbs/ft² 1-990

4Fascia Bar (#1571) with Metal

Fascia Cover (#2543)4˝ 6˝ O.C.* 990 lbs/ft² 1-825

5Gravel Stop (#1226) with Metal

Gravel Stop Cover (#2525)2˝ 8˝ O.C.* 500 lbs/ft² 1-930

6Gravel Stop (#1587) with Metal

Gravel Stop Cover (#2554)4˝ 8˝ O.C.* 280 lbs/ft² 1-990

72˝ Vinyl-Coated Drip Edge

(#2529-302)2˝ 6˝ O.C.* 400 lbs/ft² N/A

84˝ Vinyl-Coated Drip Edge

(#2529-204)4˝ 6˝ O.C.* 300 lbs/ft² N/A

94˝ Snap-On Fascia Base

(#2600B-400)4˝ 6˝ O.C.* 360 lbs/ft² N/A

106˝ Snap-On Fascia Base

(#2602B-600)6˝ 6˝ O.C.* 400 lbs/ft² N/A

11 12˝ Snap Coping Cap 12˝ 12˝ O.C.* 200 lbs/ft² N/A

12 16˝ Snap Coping Cap 16˝ 12˝ O.C.* 160 lbs/ft² N/A

Sample DescriptionSample

Size

Fastening

Pattern

SPRI Rating

(lbs/ft2)FM Rating

1 Snap Coping 12˝ 6˝ O.C. 183 lbs/ft² 230 lbs/ft²

2 4˝ Fascia Cover (#2543) 4˝ 6˝ O.C. 560 lbs/ft² 610 lbs/ft²

3 13/4˝ FasciaCover (#2537) 2˝ 6˝ O.C. 530 lbs/ft² 610 lbs/ft²

4 4˝ T-Edge (#2756-204) 4˝ 6˝ O.C. 560 lbs/ft² 610 lbs/ft²

52-Piece Base (#2600B)

with Cover (#2600T)4˝ 6˝ O.C. 604 lbs/ft² 610 lbs/ft²

Sample DescriptionSample

SizeFastening

Pattern

Average

Achieved

Pressure

(lbs/ft2)

Maximum

Achieved

Pressure

(lbs/ft2)

4Introduction

Why ES-1?A quick Reference Guide


Introduction

Q. What is ANSI?

A. The American National Standard Institute (ANSI) is a non-profit organization

that administers and coordinates a voluntary standardization system.

Q. What is SPRI?

A. SPRI, (Single Ply Roofing Industry) is a non-profit trade association repre-

senting the sheet membrane and component supplier to the commercial

roofing industry. SPRI is an official ANSI canvasser and has worked with

representatives of the roofing industry to develop a number of consensus

standards.

Q. What is FMGlobal?

A. FMGlobal provides commercial and industrial property insurance and

engineering-driven risk management solutions.

Q. What are ICC & the IBC?

A. The International Code Council (ICC) is a non-profit organization that

works to develop a single set of comprehensive and coordinated national

model construction codes. The International Building Code (IBC) provides

a consensus standard for construction codes.

Q. How and when did all these organizations get involved in setting

roofing industry standards?

A. Prior to 1980 there were no roofing edge standards by which manufacturers

could hold themselves to. FM Global then created a system of standards

and approvals to use on FM Global insured properties. The design commu-

nity adopted this system because there were no other available standards

at the time.

In 1998 SPRI developed a series of three tests for judging the quality and

durability of fascia and coping. These tests then allow for ES-1 approval.

In 2002 the IBC wrote the ES-1 guidelines into their 2003 code. Many states

have adopted the 2003 IBC, and the list is continually growing.

Currently, SPRI and FM Approvals are working together to develop the next

generation of the standard.(Continued on next page.)

Reprinted with permission from the Single Ply Roofing Industry.

5

Q. What is the ANSI/SPRI ES-1 standard?

A. It is a reference for those who design, specify or install edge materials

used with low slope roofing systems. It addresses copings and horizontal

roof edges. The following factors are considered when designing a roof edge

• Structural integrity of the substrate that anchors the edge (e.g. nailers)

• Wind resistance of the edge detail

• Materials specifications

Q. What factors are used in ANSI/SPRI ES-1to determine the loads on

a roof edge?

A. The key elements considered are:

• Wind Speed

• Building Occupancy

• Building Height

• Location of the edge device on Roof

• Building Location

Three tests prescribed in ES-1 are used to determine if a roof edge will

withstand the determined load.

RE-1: This tests the roof edge termination for mechanically attached and

ballasted roofing systems. The RE-1 test evaluates the perimeter attachment

to ensure that it meets a minimum holding power of 100 lbs./ft. The membrane

is pulled at a 45° angle to the roof deck to simulate a billowing membrane.

Failure is defined as any event that allows the membrane to come free of

the edge termination or the termination to come free.

RE-2: This is a pull-off test for metal edge flashing. It evaluates the strength

of the metal edge flashing to ensure that the fascia system meets or exceeds

the building’s calculated design wind pressure. A load is applied to the fascia

metal, simulating wind load on the fascia. The calculation used is: force at

failure X face area = blow-off resistance. The results must meet or exceed

the calculated design wind pressure of the building.

RE-3: This test is a pull-off test for metal wall coping. It evaluates the strength

of the metal coping cap to ensure that it meets or exceeds the building’s

calculated design wind pressure. A load is applied to the coping cap, simulating

wind load. Simultaneous up and out forces are used. The calculations used

to determine the blow-off resistance for the top, face leg and backleg are:

force at failure X surface area = blow-off resistance. The results must meet

or exceed the calculated design wind pressure of the building.

Q. How does the code actually read?

A. The 2003 IBC, §1504.5: “Edge securement for low-slope roofs. Low-slope

membrane roof systems metal edge securement, except gutters, installed

in accordance with Section 1507, shall be designed in accordance with

ANSI/SPRI ES-1, except the basic wind speed shall be determined from

Figure 1609.”

(Note: The Figure 1609 wind speed map varies from the wind speed map

in ANSI/SPRI ES-1 1998 in the hurricane coastal regions as the map in

Figure 1609 was updated in 2003)

The ANSI/SPRI ES-1 document can be downloaded in its entirety for free

from SPRI (www.spri.org/publications) (Continued on next page.)


Introduction 6

Q. Which areas have adopted the 2003 IBC?

A. The majority of the United States has adopted some version of the IBC.

Many states and municipalities have already or are scheduled to adopt the

2003 version of the IBC (www.iccsafe.org/government/adoption.html)

Q. Who is involved in ES-1 testing and what products have been tested?

A. There are a variety of sources available for ES-1 tested products. Most

companies producing pre-manufactured roof edge systems have had some

or all of their standard products tested in accordance with the ES-1

standard. The NRCA has done testing - go to:

http://www.nrca.net/rp/technical/details/itslisting.aspx for more details.

Q. What does this mean for me? Do you have any recommendations in

light of recent developments?

A. It is important to frequently check your local requirements because

additional states, counties and municipalities are in the process of

adopting the 2003 IBC.

Roofs with edges designed and installed to meet ES-1 provide wind

securement in the most vulnerable area of the roof, the edge.

7 800-248-0280www.exceptionalmetals.com

Introduction


Recommended Tools

Introduction

The following is a list of basic tools that are required to ensure

proper installation of most EXCEPTIONAL Metals products:

Used to flatten, seam, and bend sheet metal. These are

especially handy for jobs that are located in overhead or

confined areas.

3˝ Offset Hand Seamer

Used to seam, bend or flatten sheet metal. Compound

leverage handle offers greater holding power with

less effort.

6˝ Hand Seamer

Accurately etches straight lines on sheet metal for cutting

or bending. Adjustable in 1/16˝ increments up to 5½˝.

6˝ Scriber

Cuts left curves and straight lines. Offset design makes

longer cuts with ease.

Offset Aviation Snip Left

Cuts right curves and straight lines. Offset design makes

longer cuts with ease.

Offset Aviation Snip Right

Contains items needed to pierce up to 14-gauge mild

steel. Kit includes dies ranging from 3/32˝ – 9/32˝. Also has

an adjustable depth gauge for a maximum depth of 2˝.

Hand Punch Kit

A classic lightweight aluminum snip that is ideal for

making long straight cuts.

Pattern Snip

Pulls 1/8˝ – 3/16˝ rivets. Nose piece is adjustable and can

pull rivets straight out from confined spaces.

Hand Riveter

Item Number 3805

Item Number 3806

Item Number 3804

Item Number 3802

Item Number 3801

Item Number 3807

Item Number 3803

Item Number 3808

8


Common Industry Terms

Introduction

Anodizing – An electrolytic oxidation finishing process that coats aluminum

and produces a thin layer of aluminum oxide. This protective layer is extremely

hard and provides a long-term architectural finish (aluminum anodic oxide

coating). Available in clear or color applications. Anodized aluminum is

considered compatible with all metals.

Bonderized or Paint Grip – is galvanized steel that has been immersed in a

phosphate bath and dried in a chromate dry station during the manufacturing

process. This process produces the dull gray color that is characteristic of

bonderized metal. The phosphate coating serves as an excellent “primer” for

painting applications. Bonderized material should be painted immediately after

installation as the exposed phosphate coating is prone to white rust.

Cleat – A formed metal strip designed to hook into and secure the lower edge

of a gravel stop, extender or similar detail. A “continuous” cleat engages a

product along its entire length.

Coping – A custom-fabricated metal wall cap that covers the top of a parapet

wall or curb condition.

Counter flashing (1-piece or 2-piece) – A formed metal flashing that provides

a watertight seal/termination at the leading edge of roofing material. Counter flashing

is attached in areas where the membrane covers a wall or curb. A 2-piece

counter flashing (commonly referred to as “reglet counter flashing”) can be

removed and re-attached to make necessary repairs on the wall or curb.

Cover Plates – Formedmetal pieces usually 6˝ wide that are installed over the joints

of gravel stops, copings, gutter, and counter flashings where a lap joint is not used.

Downspout (open face or closed) – A formed metal tube used to carry

water from a roof level, scupper/collector box or gutter system to the ground.

A closed downspout is capable of transporting large volumes of water. An

open face downspout prevents ice or debris from clogging and causing potential

maintenance problems.

Drip Edge – A sheet metal “form” on the lower edge of a gravel stop, coping,

counter flashing or drain bar that is bent at a 40° angle to keep dripping water

from running directly down the face of a building.

Elbow (45° and 80°) – A downspout accessory item that is fabricated in an

angled section of downspout and used for directional changes. Available in

standard 45° or 80° versions. A-style elbows are angled away or perpendicular

to the wall. B-style elbows are angled parallel to the wall.

9

Common Industry TermsElectrolytic Action or Electrolysis (between different metals) – A galvanic

reaction caused by the presence of an electrolyte that results in the deterio-

ration of a weaker metal. The electrolyte may be rain water flowing from one

surface to another or moisture from the air containing enough acid to cause it

to act as an electrolyte.

End Cap – A metal piece formed to the shape of a gutter, coping, or

cornice, and used to close off an unfinished end.

Extender – A formed steel or aluminum fascia product that provides supple-

mentary coverage to a building perimeter when the width is not completely

terminated by a gravel stop or edge detail. Recommended for use when light

gauge materials cannot achieve coverage requirements without compromising

the strength, flatness, or aesthetic considerations.

Fascia – A horizontal piece (such as a board) covering the joint between

the top of a wall and the projecting eaves. Also called “fascia board.”

Flange, Roof Flange or Apron – The length of formed sheet metal material

that extends horizontally over the roof perimeter and is used to attach sheet

metal products and/or to “flash-in” roofing materials.

Galvalume – A coil/steel sheet that has been coated with an aluminum-zinc

alloy by a continuous hot-dip process. The nominal coating composition is

55% aluminum and 45% zinc. Duro-Last’s COOLR® metal finishes are

pre-finished galvalume.

Galvalume Plus or Acrylume – A standard galvalume coil/steel sheet with a

very thin acrylic coating applied to both sides. Not suitable for post-painting.

Galvanized Steel, G-90 – A steel coil/sheet that is coated with a minimum

0.90 oz. of zinc per square foot, giving the product excellent corrosion resistance.

G-90 galvanized steel is considered an acceptable exterior grade material.

Galvanizing – The application of a zinc coating to steel using either a hot-dip

or electro-deposition process that imparts added corrosion resistance.

Gauge – The thickness or diameter of sheet metal or wire. Dimensions are

expressed in decimal thickness or diameters.

Gravel Stop – A roof edge termination that is named for the function of

holding back gravel or ballast.


Introduction 10


Common Industry Terms

Introduction

Gutter – A water carrying device at the roof edge used to collect rain water

and melting snow from a roof surface. Gutters are manufactured in material

thicknesses starting at .032˝, 24-gauge, G-90 galvanized steel or greater.

Kynar 500® or Hylar® 5000 – An extremely durable 70% resin-based paint

coating chemically known as Polyvinylidene Fluoride (PVDF).

Lap Joint – A seam located at the end of a sheet metal product created by

placing 1-3˝ over (or under) the end of an adjacent section, eliminating the

need for covers or splice plates.

Metallic Finish – A premium paint finish that incorporates metal flakes to

create a sparkling, brilliant appearance.

Mill Finish – Metal in its raw unfinished form without a coating or finish.

Color and/or shade variations can be expected.

Miter (Inside or Outside) – A fabricated accessory sometimes referred to as

a "corner" that is usually installed at the intersection of two walls. It is produced

by cutting or bending two pieces of material and seaming them together.

Nailer – Construction-grade wood attached to a building substrate that is used

as a foundation for fastening steel or aluminum roof termination products

(treated wood nailer).

Oil Canning – The perceived waviness of a section of flat metal that exceeds

the limits for flatness for a given face height (or span) and metal thickness. Oil

canning is inherently found in light gauge, formed metal products, particularly

those products with broad flat areas. Structural integrity is not affected when

oil canning is present.

Outlet – A short metal tube that is installed into an opening in the bottom of

a gutter, collector or scupper. Used as a transition between the downspout

sections and the water collecting system.

Parapet – A perimeter wall that extends higher than the roof level.

Post-Coating – A paint or anodized finish process that is applied to a metal

product after it has been formed into its final shape.

Pre-finished – Materials that are coated with a factory-applied paint (Kynar

500® or Hylar® 5000) or anodized finish prior to sheet metal fabrication. Pre-

finished usually refers to flat metal already painted in sheet or coil form.

11

Common Industry TermsRadius – The radius of a circle is the distance from the center point to the

edge of the circle or roof. It is half the length of the diameter.

Reglet – A horizontal masonry saw cut or raked mortar joint used to attach

sheet metal counter flashing, sometimes referred to as a receiver (See

Counter Flashing, 1-piece or 2-piece).

Scupper – An opening in the side of a wall or sheet metal edge detail that

allows water to drain from the roof surface. Overflow scuppers are used as

a secondary drainage method in case of "interior drain" blockage. Spill-out

scuppers allow water to run directly over the edge of a building onto another

roof level or the ground. A downspout scupper (sometimes referred to as a

collector or conductor head) channels water into a downspout that carries

rain water to the ground or to a lower roof level.

Snap Cleat – A formed aluminum or galvanized steel attachment clip used

for securing 10' coping sections to the top of a parapet wall or curb.

Splice Plates – Formed metal pieces usually 6˝ wide that are installed

underneath the joints of gravel stops, copings, gutters, and counter flashings

when a lap joint is not used. Splice plates provide a more aesthetically-

pleasing appearance than cover plates (joint splices).

T-Miter – A steel or aluminum sheet metal product that is used at the intersection

of two parapet walls, where one wall terminates perpendicularly into a continuous

second wall.

Thermal Movement – The degree of expansion and contraction that materials

will allow due to a change in temperature. Thermal movement varies consider-

ably between different building materials. Natural materials such as stone,

timber, and brick have low thermal movement. Most metals have a medium

degree of movement and require careful joining. Plastic materials have a

high degree of thermal movement.

Transition Miter – A steel or aluminum sheet metal product utilized at the

junction (corner) of two parapet walls of different wall thicknesses.

Treated Wood – Wood planks used as wood nailers that are pressure-

treated with chemical preservatives for enhanced weatherability against

wood decay and insect damage.

Vinyl Masking or Protective Film – A removable plastic film applied for

protection during fabrication, shipping, and installation of various sheet metal

products. This film must be removed immediately before product installation.


Introduction 12


Duro-Guard Edge System products deliver high-quality performanceyour customers can depend on. For a complete listing of ANSI/SPRIES-1 compliant products, please view the chart at the beginning ofthis reference manual.

QUALITY YOU CAN TRUST

Duro-Guard Edge System Products:

• 2-Piece Compression Metal

• Gravel Stop Covers

• Fascia Bar Covers

• Snap-On Fascia Base

In Stock and Ready-To-Ship

Each Duro-Last manufacturing facility stocks 2-piece compression metal,

gravel stop covers, and fascia bar covers. These Duro-Guard products can be

shipped within five business days when ordered in the following finishes: stonewhite, slate gray, sierra tan, medium bronze, and dark bronze.

All other non-stock products are shipped within 10 business days.

Duro-Guard Features and Benefits:

• Precisely crafted to neatly terminate roof perimeters.

• Ready-to-assemble inside and outside corners are easy to install around

corners, angles, and transition areas.

• Products are end-notched to provide trouble-free piece-to-piece docking.

• 20-year limited warranty on most finishes.

Made From:

• 24-gauge Galvalume

• Can also be fabricated in:

• 24-gauge Stainless Steel

• .040 Aluminum

• 16 oz. Copper

Metal Finishes:

• 25 Kynar® finishes and Galvalume®Plus

• Bonderized metal

• Mill finish

Packaging

A protective plastic film is applied to help ensure products arrive to the job

site in good condition.

Duro-Guard® Edge System

13 Duro-Guard® Edge System



Fascia CoverItem Number 2537

Item Number 2543

Product Facts:

• Easily snaps onto Duro-Last vinyl fascia bar.

• Available in 1¾˝ and 4˝ widths; 10´ lengths.

• Both inside and outside ready-to-assemble corners are available.

• Made of 24-gauge galvalume and available in any metal finish.

• Factory Mutual Wind StormApproval Rating: 1¾˝ FM 1-990 and 4˝ FM 1-825.

• Meets ANSI/SPRI ES-1 2003 method RE-2 and TAS 111-95 testing

requirements.

• 1¾˝ – See DL #3500 for complete installation detail.

• 4˝ – See DL #3510 for complete installation detail.

Tips and Tricks:

• Allow 2½˝ overlap for each piece.

• Both the 1¾˝ and 4˝ size can be fabricated with a flat face for a different look.

• The 1¾˝ fascia bar and cover are ideal terminations into a gutter.

• Stocked in medium bronze, dark bronze, stone white, slate gray, and

sierra tan.

13/4˝

4˝

14



Item Number 2543-010

Product Facts:

• A Duro-Last exclusive product.

• Pre-notched grooves allow fascia cover to easily snap over radial surfaces.

• Can be installed on both inside and outside radius edges.

• Available in 10´ lengths and 4˝ widths only.


• See DL #3511 for complete installation detail.

Tips and Tricks:

• Allow for 2½˝ overlap on each piece.

• This detail is pre-notched at 3˝ intervals to allow the cover to flex.

• Detail can be made with a flat face.

• Pricing tip: The price of this product is slightly less than double that of the

standard fascia cover.

4" Flex Fascia Cover

15



Size Item #

3˝ 2-piece Snap-On Base 2597

3˝ 2-piece Snap-On Cover 2598

4˝ 2-piece Snap-On Base 2600B

4˝ 2-piece Snap-On Cover 2600T









These are item numbers for 24-gauge steel only.

Product Facts:

• Duro-Last’s most popular edge detail.

• Snap-on cover is double-hemmed to prevent roof material from chaffing.

• Installs on ²/12 pitch and lower.

• Base can be modified to accommodate a mansard.

• Available in 10´ lengths; 3˝ – 8˝ widths.

• Base and cover made of 24-gauge galvalume and available in any metal finish.

• Meets ANSI/SPRI ES-1 2003 method RE-2 testing requirements.

• FM Approved.


Tips and Tricks:

• Allow for a 2½˝ overlap on each piece.

• Can be ordered with a flat face to match the 2-piece snap-on flex.

• Standard cover is fabricated for use with a 40-mil membrane, so always

specify when using with a 50-or 60-mil job.

• Stocked in 4˝ and 6˝ medium bronze, dark bronze, stone white, slate gray,

and sierra tan.

2-Piece Snap-OnCompression

16



Size Item #

3˝ 2-piece Flex Snap-On Base 2596B

3˝ 2-piece Flex Snap-On Cover 2596

4˝ 2-piece Flex Snap-On Base 2600B-FLEX

4˝ 2-piece Flex Snap-On Cover 2600T-FLEX









Product Facts:


• Flex cover is made with a flat face that helps it conform to a radius.

• Base and cover are notched in 3˝ intervals.

• Notched and grooved to allow cover to easily snap over radial surfaces.

• Can be installed on both inside and outside radius edges.

• Available in 3˝ – 8˝ widths.

• Base and cover made of 24-gauge galvalume and available in any metal finish.


Tips and Tricks:

• Standard 2 piece cover can be ordered with a flat face to match this detail.

• This edge trim does not conform to an arched or vaulted radius.

• Pricing tip: The pricing on this product is slightly more than double that

of the standard 2 piece system.

2-Piece Flex Snap-OnCOMPRESSION

17



SNAP-ON Fascia Base

Size Item #

4˝ Fascia Base 2600B-400





Product Facts:

• Functions as a fascia bar and cove system.

• Is used with 2-piece compression cover.

• Ideal for sloped roofs with pitches ²/12 and greater.

• Available in 10´ lengths; 4˝ – 8˝ widths.

• Meets ANSI/SPRI ES-1 2003 method RE-2 testing requirements for 4˝ and 6˝.


Tips and Tricks

Allow for 2½˝ overlap on each piece of cover.

18



Gravel Stop Covers

Item Number 2554

4˝

2˝


Product Facts:

• Fits over Duro-Last vinyl gravel stop base.

• Available in 10´ lengths; 2˝ and 4˝ widths.

• Both inside and outside ready-to-assemble corners are available.


• Meets ANSI/SPRI ES-1 2003 method RE-2 testing requirements.

FM Approved.

• 2˝- See DL #3520 for complete installation detail.

• 4˝- See DL #3530 for complete installation detail.

Tips and Tricks:

• Allow 2½˝ overlap on each piece.

• 2˝ cover has a drip kick.

• 4˝ cover has a flat face.

• Stocked in 2˝ and 4˝ medium bronze, dark bronze, stone white, slate gray,

and sierra tan.

19

Duro-Guard® Edge System 800-248-0280www.exceptionalmetals.com

Size Item #

3˝ Edge Extender 2530-003






31⁄2˝ Cleat 2742-001

This is not a Duro-Guard® Edge System product, but is

used in conjunction with Duro-Guard products.

Product Facts:

• Can be used with all edge details, including gutters and copings.

• Available in 3˝ – 8˝ widths.


• When ordering, allow a minimum 1˝ lap under the edge detail.


Tips and Tricks:


• Extenders with face sizes wider than 8˝ can be made with a stiffener beak

to minimize oil canning.

• Any extender with a width size greater than 4˝ must use a continuous cleat.

Edge Extender

20

Scupper Features and Benefits:

• Can be fabricated to specific through-wall measurements to solve

drainage challenges.

• Available with an exterior metal flange that provides an aesthetically-

pleasing finish.

• Prefabricated scuppers with a 2˝ terminating metal flange reduce field

fabrication and installation time.

Scupper Skirts

Scupper skirts are made with 40-mil Duro-Last membrane.

• Scupper skirts are available in:

• White

• Tan

• Gray

• Standard skirt length is 6˝. Custom length skirts are available upon request.

Made From:

• 24-gauge vinyl-coated metal

Metal Flange Finishes:

Can be fabricated in:



• .040 Aluminum


Proper Scupper Measurement:

• A = Height

• B = Width

• C = Length (through-wall)

• Be sure to subtract ¼˝ from height and width dimensions for every scupper.

• Add 1˝ to the through-wall length when ordering single skirt scuppers.

• Use exact through-wall length when ordering metal flange and/or double

skirt scupper.

Pitch Pans

Prefabricated pitch pans deliver a watertight seal around rooftop protrusions.

Made From:


Pitch Pan Skirts

Pitch Pan skirts are made from 40-mil Duro-Last membrane.

• Pitch Pan skirts are available in:

• White

• Tan

• Gray

• Standard skirt length is 6˝. Custom length skirts are available upon request.

Scuppers/Pitch Pans

800-248-0280www.exceptionalmetals.com21 Scuppers/Pitch Pans


Scuppers/Pitch Pans

Item Number 2701 Series

Product Facts:

• Eliminates difficult field fabrication, saving time and labor.

• Features 2˝ termination flange behind the skirt for easier installation.

• Made with vinyl-coated metal.


Tips and Tricks:

• When ordering, always remember to subtract ¼˝ from the actual height

and width of the scupper opening and add 1˝ to the length.

• Select white, tan or gray membrane skirt.

• Colors can be mixed or matched.

Single Skirt Scupper

22


Scuppers/Pitch Pans

Item Number 2701 Series

Product Facts:





Tips and Tricks:


and width of the scupper opening.

• Most commonly used with the vinyl-back collector (Item #2730).

• When installed without the collector, this scupper must be terminated

according to specifications.


Double Skirt Scupper

23


Scuppers/Pitch Pans

Item Number 2702

Product Facts:

• Offers superior water drainage and aesthetically-pleasing finish.


• Flange can be ordered in any metal finish.



Tips and Tricks:


and width of the scupper opening.

• Remember to terminate around the opening on the inside of the parapet wall.

• 2˝– 4˝ flanges are standard.



Scupper with decorativeMetal Flange

24


Scuppers/Pitch Pans

Size Item #

3˝ 2 piece Spill-Out Scupper 2703-003






Product Facts:

• Used with any sized 2 piece snap-on compression.

• Outside Duro-Last membrane corners are used to terminate the deck sheet

over the spill-out scupper base and roof edge to ensure watertightness.

• Detail consists of: 18˝ long vinyl-coated base, two outside corners, and a

24˝ cover and spill-out with skirt.


Tips and Tricks

Select white, tan or gray membrane skirt.

Spill-Out Scupper

25


Scuppers/Pitch Pans

Vinyl-Coated Pitch Pan

Item Number 2765

Product Facts:

• Delivers watertight seal around rooftop protrusions.

• Available in customizable lengths and widths with a minimum 8˝ height.

• Made of vinyl-coated metal and 6˝ 40-mil Duro-Last membrane skirt.


Tips and Tricks

Select white, tan or gray membrane skirt.

26


Collectors/Conductors Benefits and Features:

• Eliminate field fabrication, saving time and labor.

• Precisely crafted to exact specifications.

• Allows maximum water flow.

• Conductor can be used with metal flange scupper or installed under

an existing scupper.

Made From:




• .040 Aluminum

Metal Finishes:



• Mill finish

Packaging

A protective plastic film is applied to help ensure products arrive to the job


collectors/CONDUCTORS

Collectors/Conductors27


Collectors/Conductors

Vinyl-Back Collector

Item Number 2730

Product Facts:


• Double-skirt scupper is factory-attached to vinyl-coated back, making field

installation quick and easy.

• Collectors are constructed with a Pittsburgh seam that eliminates the

need for rivets and creates a watertight product.

• Attached scupper is made from 24-gauge vinyl-coated metal that includes

a Duro-Last membrane skirt.

• Available in any metal finish.


Tips and Tricks:

• The collectors are sized according to the scupper size (plus 6˝)

and downspout size, using SMACNA guidelines.

• When ordering, specify downspout size.

• Overflow cutouts can be incorporated in the face or sides, upon request.

28


Collectors/Conductors

Item Number 2766

Product Facts:

• Conductors are designed to attach to the wall below the scupper, leaving

the scupper visible from the ground.

• Standard designed conductors have the same appearance as the

vinyl-back collector.

• Can be used with metal flange scupper or installed under an existing scupper.



Tips and Tricks

Conductors are most commonly ordered with a metal flange scupper

(Item #2702), producing an attractive combination.

Conductor

29

Gutters/downspouts

X-Series & Riveted Gutter Dimensions:

EX-4, E-4

EX-5, E-5

EX-6, E-6

6˝

7˝

7˝

4˝

5˝

6˝

4˝

5˝

5˝

MX-4, M-4

MX-5, M-5

MX-6, M-6

6˝

7˝

7˝

4˝

5˝

6˝

4˝

5˝

5˝

DX-4, D-4

DX-5, D-5

DX-6, D-6

6˝

7˝

7˝

4˝

5˝

6˝

4˝

5˝

5˝

LX-4, L-4

LX-4, L-5

LX-4, L-6

6˝

7˝

7˝

4˝

5˝

6˝

4˝

5˝

5˝

Style A B C


Gutter Features and Benefits:

• Four box-style profiles are available in three sizes each.

• Internal splice plates eliminate the need to completely rivet sections together.

• Assembled inside and outside miters can be fabricated to any angle.

• Gutter strap hooks into the top front edge of gutter and is installed onto

the back of the gutter, using one rivet instead of two.

• Redesigned gutter strap hook drops 5/8˝ from the top edge, eliminating

the possibility of water wicking over the front of the gutter.

• Roof flanges can be bent to accommodate various roof pitches.

• Can be made up to 20´ long. These extended lengths require a dedicated

flatbed to transport.

• Custom sizes and profiles are available.

Made From:




• 16 oz. Copper

• .040 Aluminum

Metal Finishes:



Packaging:

• X-style box gutters are shipped nestled inside each other to reduce

shipping costs.

• A protective plastic film is applied to help ensure products arrive to the job


(Continued on next page)

Gutters/Downspouts 30


Downspouts Features and Benefits:

• Downspouts have tapered ends that nest together up to 3˝ and eliminate

the need for any field notching or crimping.

• Closed downspouts feature a Pittsburgh seam for a professional finish

that also eliminates the need for rivets.

• Open-Face downspouts help eliminate blockage due to ice and debris

build-up.

Made From:



• 24-guage Stainless Steel

• 16 oz. Copper

• .040 Aluminum

Metal Finishes:



Packaging

A protective plastic film is applied to help ensure products arrive to the

job site in good condition.

Gutters/Downspouts31


Gutters/Downspouts

EX-Style Item # E-Style Item #

EX-4 2745-081 E-4 2745-080

EX-5 2745-091 E-5 2745-090

EX-6 2745-101 E-6 2745-100

Product Facts:

• Available in three standard sizes.

• Front profile features an 80° angle.

• 18-gauge hook straps can be ordered installed or ready to install in the field.

• Can be customized to meet specifications.


• EX-Style – See DL #DL2091 for complete installation detail.

• E-Style – See DL #DL2090 for complete installation detail.

Tips and Tricks:

• Gutters with bottom dimensions of 8˝ and greater require a hanger to

support the added weight load.


• Pricing Tip: X-series gutter is more economical than riveted gutter.

Ex-Style, E-Style Gutters

32


Gutters/Downspouts

MX-Style Item # M-Style Item #

MX-4 2745-111 M-4 2745-110

MX-5 2745-121 M-5 2745-120

MX-6 2745-131 M-6 2745-130

Product Facts:


• Front profile features a 72° angle and 2˝ top bend.



• Available in any metal finish

• MX-Style – See DL #DL2091 for complete installation detail.

• M-Style – See DL #DL2090 for complete installation detail.

Tips and Tricks:

• Gutters with bottom dimensions of 8˝ and greater require a hanger to sup-

port the added weight load.



MX-Style, M-Style Gutters

33


DX-Style, D-Style Gutters

Gutters/Downspouts

DX-Style Item # D-Style Item #

DX-4 2745-021 D-4 2745-020

DX-5 2745-031 D-5 2745-030

DX-6 2745-041 D-6 2745-040

Product Facts:


• Front profile features a 45° angle.




• DX-Style – See DL #DL2091 for complete installation detail.

• D-Style – See DL #DL2090 for complete installation detail.

Tips and Tricks:





34


LX-Style, L-Style Gutters

Gutters/Downspouts

LX-Style Item # L-Style Item #

LX-4 2745-051 L-4 2745-050

LX-5 2745-061 L-5 2745-060

LX-6 2745-071 L-6 2745-070

Product Facts:


• Front profile features a classic 90° angle.




• LX-Style – See DL #DL2091 for complete installation detail.

• L-Style – See DL #DL2090 for complete installation detail.

Tips and Tricks:





35


Gutters/Downspouts

Removable Gutter System Features and Benefits:

• Patent-pending gutter system is distributed exclusively by Duro-Last®

Roofing, Inc.

• Innovative design allows for excellent thermal movement and easy gutter

replacement.

• System consists of: custom gutter box, vinyl-coated drip edge, and gutter

bracket.

• Select from two different styles to match building design.

• Option 1: Designed to be used when a fluted roof is flush with the eave.

• Option 2: Designed to be used with projects with a slight over-the-eave.

Use this system when thermal movement is a factor.

• No need to remove and re-attach existing terminations, thus minimizing

material replacement and helping reduce labor costs.

• Available in 10´ lengths.

• Option 1 – See DL #2100 for complete installation detail.

• Option 2 – See DL #2105 for complete installation detail.

Made from:

• 24-gauge Steel.



• .040 Aluminum

Metal finishes:

• 25 Kynar® finishes and Galvalume® Plus


Tips and Tricks:

• Because the gutter is not attached to the building, it actually “floats” on

the drip edge and expands and contracts freely.

• The roof’s edge is terminated with vinyl-coated drip edge. If a section is

damaged, it can be replaced without disturbing the edge.

Option 1 Option 2

Removable Gutter System

36


Gutters/Downspouts

Gutter Miter: Item Number 2755 Series

• Can be fabricated to any angle to provide

a professional transition around corners.

• All miters are riveted and sealed.

• Inside and outside miters are available.

End Caps: Item Number 2747 & 2748 Series

• Fabricated to custom sizes and profiles.

• Left and right end caps are available.

Splice Plates: Item Number 2755 Series

• Internal splice plates reduce installation time.

Drop/Outlet: Item Number 2749 Series

• Required to attach gutters to downspouts.

• Can be custom ordered to meet gutter dimensions.

Rivets: Item Number 1400 Series

• Available in standard and custom colors.

• 250 per bag.

Gutter ACCESSORIES

37


Gutters/Downspouts

Item Number 2754 SeriesItem Number 2750 Series

Product Facts

Closed Downspouts:

• Feature a Pittsburgh seam for a professional finish that also eliminates

the need for rivets.

• Standard length is 10´.

• Custom sizes and assemblies are available.



Open Face Downspouts:

• Help eliminate blockage due to ice and debris build-up.

• Custom sizes are available.



Tips and Tricks:

• A downspout ordered in aluminum will have a riveted seam because

the material is too brittle to form a Pittsburgh seam.

• The tapered downspout design allows it to nest together up to 3˝,

eliminating the need for any field notching or crimping.

• Downspout straps are sold in 10˝ lengths to be cut in the field for any

hanging requirement.

• Open face downspouts are not tapered and will nest together by simply

cutting a 1˝ notch out of each side of the receiving piece.

• Bottom kickout elbows can be cut into both open and closed downspouts.

Downspouts

38


Gutters/Downspouts

Customized DownspoutAssembly

Product Facts:

• Can be customized with multiple bends to meet any water drainage or

collection need.

• Elbows can be incorporated into the downspout assembly for multiple bends,

eliminating field assembly.

39


Gutters/Downspouts

A-Style Elbow: Item Number 2752 Series

• Directs water away from building.

• Available in 45° and 80° angles.


B-Style Elbow: Item Number 2752 Series

• Directs water alongside the building.

• Available in 45° and 80° angles.


Square-To-Round Adapters: Item Number 2749-200

• Allow for quick transition into roof drainage systems.

• Order square-to-round adapter to specific dimensions.

• Made of galvalume steel.


Drainage Accessories

40

coping systems


Coping System Features and Benefits:

• Offers a complete finish for any parapet wall.

• Riveted inside and outside miters and end caps are available with all coping

sizes and styles.

• Concealed splice plates provide a smooth color match appearance from the

top to the back of the coping cap.

• Maximum length is 10´.

Three Available Coping Systems:• Snap

• Canted

• Flat

Made From:




• 16 oz. Copper

• .040 Aluminum

Metal Finishes:



Packaging

A protective plastic film is applied to help ensure products arrive to the job site

in good condition.

Coping Systems41


Coping Systems

Item Number 2740-S

Snap Coping

Product Facts:

• Easily snaps onto 16-gauge cleat segments with no crimping required.

• Concealed splice plates eliminate exposed fasteners and allow for

thermal movement.

• Both inside and outside prefabricated corners are available.

• Available in 10´ lengths; widths are customized to specification.


• Meets ANSI/SPRI ES-1 2003 method RE-2 testing requirements for

12˝ and 16˝ wall dimensions.

• Meets TAS 111-95 testing requirements for 12˝ wall dimension.


Tips and Tricks:

• Minimum fabrication size is: 4˝ face X 8˝ top X 3˝ back.

• Cleats are spaced 5´ on-center on parapet walls.

42


Canted Coping

Coping Systems

Item Number 2740

Product Facts:

• Perfect for parapet wall areas requiring water to drain towards the roof side.

• Offers the same appearance of the snap coping, but utilizes the 2-piece

base as the continuous cleat system.

• 6˝ concealed-plate allows for expansion and contraction.

• Pre-punched continuous cleats help ensure proper fastener placement.




• See DL#6052 for complete installation detail.

Tips and Tricks:

• The cleat slopes the cap from front to back to help contain the water

on the roof.

• Canted coping uses a continuous cleat system. Perimeter fastening is

required along with exposed fasteners on the inside of the parapet.

43


Flat Coping

Coping Systems

Item Number 2740

Product Facts:

• Coping rests flat on top of the parapet.

• Delivers an attractive finish along parapet walls.

• 6˝ concealed splice plate provides coverage for expansion and contraction.




• See DL#6050 for complete installation detail.

Tips and Tricks

Install flat coping by using a continuous face cleat and fastening the back leg

to the inside wall, using a grommeted screw.

44

Vinyl-Coated Products Features and Benefits:

• Save time by providing easy installation between challenging areas and

roof decks or transition areas.

• Eliminate waste; no need to stock costly metal or vinyl products.

• Products can be custom fabricated to meet specific project challenges.

Vinyl-Coated Products Made With:


• Scupper skirts made with 40-mil Duro-Last membrane are available in:

• White

• Tan

• Gray

• Membrane colors can be mixed and matched.


vinyl-coated products

Vinyl-Coated Products45


Vinyl-Coated Products

Size Item #

2˝ T-Edge 2756-203

3˝ T-Edge 2756-206

4˝ T-Edge 2756-204

5˝ T-Edge 2756-207

6˝ T-Edge 2756-205

31⁄2˝ Cleat 2742-001

Hook Strip 2756-220

Product Facts:

• Provides a smooth edge finish and easy deck sheet termination.

• Great for use in terminations that cannot be face fastened.

• Aesthetically-pleasing metal base can be made in any finish.

• The hook strip can be sold separately.

• The splice plate bridges the gap between two sections of T-edge.

• T-edge can be modified to accommodate various mansard pitches.


The Duro-Last T-edge detail consists of three separate components: a drip

edge base, hook strip, and splice plate that are hooked together to form an

aesthetically-pleasing edge.

The top piece consists of a vinyl-coated hook strip with a 6˝ attached

membrane skirt. The bottom drip edge piece is available in any metal finish.

Tips and Tricks:

• T-edge utilizes a splice plate and does not require an overlap allowance.

• Drip edge components can be made from any metal finish or material

(except 16 oz. Copper).

• The hook strip component of this detail is not compatible with 16 oz. Copper.

• Chose white, tan or gray hook strips and membrane skirt.

• Face size of 4˝ and larger must be installed with a 3½˝ continuous cleat.

T-Edge

46



Size Item #

2˝ T-Edge Plus 2756-402

3˝ T-Edge Plus 2756-403

4˝ T-Edge Plus 2756-404

5˝ T-Edge Plus 2756-405

6˝ T-Edge Plus 2756-406

31⁄2˝ Cleat 2742-001

Hook Strip 2756-220

Product Facts:

• This detail has all the same features as our original T-edge.

• Redesigned double-folded drip edge neatly conceals the vinyl-coated hook

strip so that it is not visible from ground level.

• The hook strip can be sold separately.

• The splice plate bridges the gap between two sections of T-edge.

• T-edge can be modified to accommodate various mansard pitches.


The Duro-Last T-edge detail consists of three separate components: a drip

edge base, hook strip, and splice plate that are hooked together to form an

aesthetically-pleasing edge.

The top piece consists of a vinyl-coated hook strip with a 6˝ attached

membrane skirt. The bottom drip edge piece is available in any metal finish.

Tips and Tricks:

• T-edge utilizes a splice plate and does not require an overlap allowance.

• Drip edge components can be made from any metal finish or material

(except 16 oz. Copper).

• The hook strip component of this detail is not compatible with 16 oz. Copper.

• Chose white, tan or gray hook strips and membrane skirt.


T-Edge plus

47


Vinyl-Coated Drip Edge


Size Item #

2˝ Vinyl-Coated D/E With Skirt 2529-302





31⁄2˝ Cleat 2742-001

Product Facts:

• Provides maximum water flow from roof decks with professional termination.

• Attached vinyl skirt welds to deck membrane.


Tips and Tricks:


• Vinyl-coated drip edge is available in white, tan, or gray, and can also be

painted with latex or acrylic paint to match building design.

• Can be fabricated to accommodate various roof pitches and mansards

with a maximum face size of 8˝.


48


Vinyl-Coated SnowDiverter and Snow Guard


• Snow diverters help keep snow from accumulating around roof vents.

• Can be used for sloped roofs with pitches ²/12 and greater.

• Choose white, tan, or gray vinyl-coated metal and membrane skirt.

Snow Diverter: Item Number 1240

• Prevent large sections of ice and snow from sliding off roof edges.

• Can be used for sloped roofs with pitches ²/12 and greater.

• Choose white, tan, or gray vinyl-coated metal and membrane skirt.

• Call Duro-Last® Engineering Services for installation details.

Snow Guards: Item Number 1391

49

Custom fabrication

If you can draw it, we can make it!


Custom Fabrication Features and Benefits:

• Highly-skilled staff who will design a quality-assured product

to meet your needs.

• Eliminates need for investing in costly forming equipment.

• No need to keep metal stocked.

• Quick turnaround time.

Can Fabricate:


• Vinyl-coated Metal


• 16 oz. Copper

• .040 Aluminum

• Bonderized Steel

Custom Fabrication 50


1-Piece Reglet

Custom Fabrication


Product Facts:

• Installed over termination bars located along parapet walls to deliver a

watertight, professional finish.

• Shields fasteners from elements, preventing oxidation.




Tips and Tricks:

• Reglets are custom-fabricated to specific projects.

• When possible, verify measurements in the field to ensure accuracy.

• Call EXCEPTIONAL Metals at 800-248-0280 for fabrication quotes and

delivery times.

51


2-Piece Reglet

Custom Fabrication


Product Facts:

• Provides extended watertight protection along parapet wall termination.

• Top component attaches into parapet wall reglets, and bottom flashing

rivets into place.

• Bottom flashing is easily removed for re-roofing or maintenance.

• Use rivets to secure counter flashing to the receiver.




Tips and Tricks:

• Reglets are custom-fabricated to specific projects.

• When possible, verify measurements in the field to ensure accuracy.

• Call EXCEPTIONAL Metals at 800-248-0280 for fabrication quotes and

delivery times.

52


DURO-FLASH II™

Custom Fabrication

Product Facts:

• Used as a termination under existing metal counter flashing.

• Consists of a 3˝ wide vinyl-coated metal piece with an attached 12˝

Duro-Last® membrane skirt.


• Available in white, tan, and gray.

Tips and Tricks:

• Custom fabricated.

• Colors can be mixed and matched.

• Membrane skirt extends 3˝ past the vinyl-coated metal on each end to

allow adjacent sections to be heat welded together.

Color Item #

White 2240

Tan 2241

Gray 2242

Shown installed with1-piece reglet.

53


Custom Fabrication

Custom Cornice Flashing

Item Number 2772

Product Facts:

• Decorative flashing that delivers a contoured appearance around

building perimeters.

• Available in up to 5´ lengths.


Tips and Tricks:

• Verify measurements in the field to ensure accuracy.

• Call EXCEPTIONAL Metals at 800-248-0280 for fabrication quote and

delivery times.

54

Call EXCEPTIONAL Metals for more information.


Standing Seam Panels

Standing Seam Panels55


Fascia Cover

2-Piece Snap-On

Compression

Snap-On

Fascia Base

Snap Coping

Vinyl-Back

Collector Box

Downspout

Assembly

Metal Flange

Scupper

DX-Style Gutter

A

B

C

D

E

F

G

H

A

G

F

B

H

E

D

C

Details

Details 56

A 20-year limited warranty is available on most finishes.A sample warranty is available upon request.

FILE PROPERTY TEST METHOD COOLR™ PAINT

Color Availability See Reverse Side

Warranty 20-Year Limited

Solar Spectrum Reflectivity Solar Spectrum Reflectometer toASTM C-1549

Varies By Color

Thermal Emittance ASTM C-1371 Varies by color

Abrasion Coefficient ASTM D-968 67 Liters +/- 10

Adhesion (Crosshatch and X-Cut) ASTM D-3359 No Loss

Chemical Resistance ASTM D-1308 Procedure 7.2 10% Hydrochloric Acid 24-Hour =No Visible Change

20% Hydrochloric Acid 18-Hour =No Visible Change

20% Sulfuric Acid 18-Hour =No Visible Change

25% Sodium Hydroxide 1-Hour =No Visible Change

20% Muriatic Acid 15 Minutes =No Visible Change

Color Uniformity (Non-Metallics) ASTM D-2244 Color controlled instrumentallyand/or visually

Erosion 10 years 45˚ South Florida 0.1 Mils or Less in 20 Years

Weathering-Chalk Resistance ASTM D-659 Maximum Rating 8

Weathering-Color Retention ASTM D-2244 Maximum 5 Hunter Delta E UnitsColor Change - Not Applicable for

Metallics, Regal Red, or Matte Black

Direct Impact Flexibility ASTM D-2794 Excellent, no removal

Reverse Impact FlexibilityASTM D-2794

Excellent, no cracking,no film removal

Pencil Hardness ASTM D-3363 HB Minimum

Salt Spray Resistance ASTM B-117 1,000 HoursScribe: 7 - 1⁄16˝ BlistersField 10: No Blisters

Humidity Resistance ASTM D-2247 2,000 HoursRating 10: No Blisters

Specular Gloss ASTM D-523 60˚ = 20-35

Tunnel Test ASTM E-84 Class A coating

Recycled Content N/A 25%

ENERGY STAR® Compliant Meets ENERGY STAR®

requirements (Steep Slope)

Colors shown are matched as accurately as possible, but may vary slightlyfrom finished product.“Duro-Last” and “The World’s Best Roof” are registered marks owned byDuro-Last Roofing, Inc.Kynar 500® PVDF is a registered trademark of ElfAtochem North America, Inc.Hylar 5000® PVDF is a registered trademark of Solvay Solexis, Inc.

www.exceptionalmetals.com

800-248-0280EXCEPTIONAL Metals Reference Manual 12/08 – M#09-0001

My Ceros Download - Kelly Roofing€¦ · 800-248-0280 EXCEPTIONAL Metals, a division of...

Documents

Transcript of My Ceros Download - Kelly Roofing€¦ · 800-248-0280 EXCEPTIONAL Metals, a division of...