MW24 - Poclain Hydraulics · Hydraulic motors MW24 POCLAIN HYDRAULICS ... 4 547 2 413 1 486 743 [2...
Transcript of MW24 - Poclain Hydraulics · Hydraulic motors MW24 POCLAIN HYDRAULICS ... 4 547 2 413 1 486 743 [2...
T E C H N I C A L C A T A L O G
MW24HYDRAULIC MOTORS
Hydraulic motors MW24 POCLAIN HYDRAULICS
2 08/01/2013
CHARACTERISTICS
Contact your Poclain Hydraulics application engineer to find out how the displacement shift from the third to the second displacement is controlled and to find out trans-mission capabilities in terms of displacement shift when the vehicle is in motion.
2 857 1 516 934 467[174.2] [92.5] [57.0] [28.5]4 547 2 413 1 486 743
[2 310] [1 226] [755] [378]
2 587 1 423 934 467[157.8] [86.8] [57.0] [28.5]4 117 2 265 1 486 743
[2 092] [1 150] [755] [378]
2 506 1 253 934 467[152.8] [76.4] [57.0] [28.5]3 988 1 994 1 486 743
[2 026] [1 013] [755] [378]
2 449 1 224 702 351[149.4] [74.7] [42.8] [21.4]3 898 1 948 1 117 559
[1 980] [990] [568] [284]
2 252 1 301 856 428[137.3] [79.3] [52.2] [26.1]3 584 2 071 1 362 681
[1 821] [1 052] [692] [346]
1 947 973 856 428[118.7] [59.3] [52.2] [26.1]3 099 1 549 1 362 681
[1 574] [787] [692] [346]
90 60 50 40[121] [81] [67] [54]
90 45 50 30[121] [60] [67] [40]
450[6 530]
92 185 210 250
80 138 210 250
73 147 250 250
72 143 192 250
69 126 192 250
63 118 192 250
Q1
61
L2
H2
92
09
Displacementcm³/tr
[cu.in/rev.]
Nm[lb.ft]
Max.speed tr/min[RPM]
cm³/tr
[cu.in/rev.]
Nm[lb.ft]
tr/min[RPM]
cm³/tr
[cu.in/rev.]
Nm[lb.ft]
tr/min[RPM]
cm³/tr
[cu.in/rev.]
Nm[lb.ft]
tr/min[RPM]
cm³/tr
[cu.in/rev.]
Nm[lb.ft]
tr/min[RPM]
Cams
Max. pressure bar[PSI]
kW [HP]
Displacement
Max.speed
Displacement
Max.speed
Displacement
Max.speed
Displacement
Max.speed
Displacement
Max.speed
cm³/tr
[cu.in/rev.]
Nm[lb.ft]
tr/min[RPM]
4-displacement motor
kW [HP]
A
RMax.power
Th. torque at 100 barTh. torque at 1000 PSI
Th. torque at 100 barTh. torque at 1000 PSI
Th. torque at 100 barTh. torque at 1000 PSI
Th. torque at 100 barTh. torque at 1000 PSI
Th. torque at 100 barTh. torque at 1000 PSI
Th. torque at 100 barTh. torque at 1000 PSI
08/01/2013 3
CONTENT
POCLAIN HYDRAULICS Hydraulic motors MW24
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
Model code 5
Wheel motor 7Dimensions for standard motor 7Load curves 8Wheel rim mountings 9Hydraulic connections 10
Brakes 11 DYNA+™ Brake 11
Options 13
Hydraulic motors MW24 POCLAIN HYDRAULICS
4 08/01/2013
MODEL
4
1 2 3
H
1 2 3
D
4
M 2 4W
4
«valving system side»
«bearing support
side»
Standard pistonStandard rings 1 1High efficiency rings 2 2
Cylinder block
1091/545 [66.7/33.3] 61572/786 [95.9/48] 91747/873 [106.6/53.3] 0
1660/961/699 [101.3/58.6/42.7] H1922/1049/873 [117.3/64/53.3] M1397/873/524 [85.3/53.3/32] Q
Cam «valving system side»cm³/tr[cu.in/rev.]
4-displacement valving 4
Preferential direction of rotationClockwise DCounterclockwise G
702/351 [42.8/21.4] 9780/390 [47.6/23.8] 0856/428 [52.2/26.1] 1934/468 [57/28.6] 2
Cam «bearing support side» cm³/tr[cu.in/rev.]
Hydraulic connections
ISO 6162ISO 9974-1 1
ISO 6162ISO 11926-1 7
Without mounting 1Lug fixing 2
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 5
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
CODE
MODEL CODE
7 1
1 2
P
3 4 1 2
S
3 4 5 6
7 Dyna+™ bearing
Wheel rim mountings8 x M20 Ø 275 210 x M22 Ø 335 5
Dyna+™ brake 1
Without Options or Adaptations 0T4 speed sensor (without rotation direction) 2Predisposition for speed sensor 8TR speed sensor (digital rotation direction) STD speed sensor (two phase shifted frequencies) Q
With studs + nuts 2With studs 3
Hydraulic motors MW24 POCLAIN HYDRAULICS
6 08/01/2013
Methodology :This document is intended for manufacturers of machines that incorporate Poclain Hydraulics products. It describes the technical characteristics of Poclain Hydraulics products and specifies installation conditions that will ensure optimum operation. This document includes important comments concerning safety. They are indicated in the following way:
This document also includes essential operating instructions for the product and general information. These are indicated in the following way:
The views in this document are created using metric standards. The dimensional data is given in mm and in inches (inches are between brackets and italic)
Associated documents
Poclain Hydraulics Patents
Safety comment.
Essential instructions.
General information .
Information on the model number.Information on the model code.
Weight of component without oil.
Volume of oil.
Units.
Tightening torque.
Screws.
Information intended for Poclain-Hydraulics personnel.
Document type N°Generic installation 801478197L
Document type N°MW motor FR2796992MW motor US6347572Dyna +™ brake FR2796886Dyna +™ brake US6357558Dyna +™ brake FR2797008
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 7
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
WHEEL MOTOR216 kg [475 lb]
5.00 L [300 cu.in]
Dimensions for standard motor
Ø 385[15.16 dia.]
15°
15°
15°
15°Ø 425 max.[16.73 dia.]
185
[7.2
8]
Y1
Y2
AR 1
Hydraulic motors MW24 POCLAIN HYDRAULICS
8 08/01/2013
Load curves
Permissible radial loads Service life of bearingsTest conditions : Test conditions :
Static : 0 tr/min [0 RPM] 0 bar [0 PSI] L : Millions B10 revolutions at 150 bars (average pressure), with 25 cSt fluid, code 0 displacement, without axial load.
Dynamic : 0 tr/min [ 0 RPM], code 0 displacement, without axial load at max. torque
7 7 11 2 3 4
P
Actual output torque
The starting torque is taken to be approximately 85% of the first value for available pressure. For a precise calculation, consult your Poclain Hydraulics application engineer.
The service life of the components is influenced by the pressure.You must check that the combination of forces applied (Axial load / Radial load) is compatible with the permissible loads for the components, and that the resulting service lives of these components complies with the application's specifications. For an accurate calculation, consult your Poclain Hydraulics application engineer.
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 9
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
Wheel rim mountings
Studs
A (1) B C L
7 2 11 4
7 5 11 4
[8.69 dia.]
Ø 220.82 3
P
Ø 275
[14.17 dia.][10.83 dia.]8 x M20x1.5
55
[2.17]
Ø 360
[2.17]2 3
P[8.69 dia.] [13.19 dia.] [14.17 dia.]
10 x M22x1.555Ø 220.8 Ø 335.0 Ø 360.0
L
Ø AØ
BØ C
(1)+ 0 [+ 0]- 0.2 [- 0.008]
0.5 0.02 [ ]
45°
min. min.
M20x1.5 3.5 [0.14] 29 [1.14] 25 [0.98] 12.9 600 [442.5] 770 [567.9]
(2)(1)DC C
(*) The tightening torques are given for the indicated loads.(1) Wheel rim : Suggested tightening torque for wheel rim mountings (Re steel disc > 240 N/mm² [>34 800 PSI]).(2) Standard : Suggested tightening torque in other cases (Re steel flange 360 > N/mm² [>52 215 PSI])
Class
Studs
(*)min. max.
Hydraulic motors MW24 POCLAIN HYDRAULICS
10 08/01/2013
Chassis mountings
Hydraulic connections
Take care over the immediate environment of the connections.
For other chassis mounting possibilities, please consult your Poclain Hydraulics engineer.
To find the connections’ tightening torques, see the brochure “Installation guide” N° 801478197L.
You are strongly advised to use the fluids specified in brochure “Installation guide” N° 801478197L.
Do not put either a check valve or a poppet valve on the pilot line.
Ø M
Ø U
45°
1.5 0.06 [ ]min. min.
ØM (1) ØU S Ra V
330 385 0.2 12.5µm 690 N.m[12.99] [15.16] [0.008] [0.49µin] [508.9 lb.ft]
2 x 5 x M20 12.9
Class
(1) + 0,3/+0,2 [+ 0.012 /+ 0.008]
(*) The tightening torques are given for the indicated loads.
(*)
A 1 R X XD
ISO 6162 ISO DP6162 DN 19 PN400 DN 19 PN400
DIN 3852 ISO 9974-1 M22 x 1.5 M16 x 1.5 M14 x 1.5
ISO 6162 ISO DP6162 DN 19 PN400 DN 19 PN400
SAEJ514 ISO 11926-1 7/8" 14 UNF3/4"
16 UNF9/16"
18 UNF3/4" 16 UNF
M16 x 1.5
7
1
Y1-Y3
7 1
1 2 3 4 1 2 3 4 5 6
4
1 2 3
M 2 4W
41 2 3 4
H P SD
ReturnPower supply
1st or 3rd
displacementcontrol
Standards Power supply Case drainOld standards
Control of parking break
Control of servicebreak
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 11
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
BRAKES DYNA+™ Brake
Brake operationThis mutli-disk brake operates in two distinct ways:• Either by an absence of pressure (static braking): The spring applies a force to the static piston that is transmitted to the dynamic piston,
which clamps the fixed and free disks, preventing the shaft from turning. Braking torque decreases linearly as a function of unlocking pressure.
• Or by braking pressure (dynamic braking). The braking command creates a pressure on the dynamic braking piston, which clamps the fixed and free disks, preventing the shaft from turning. Braking torque increases linearly as a function of the unlocking pressure.
Brake release pressure vented.
Do not use both dynamic and parking brake simultaneously.
The use of certain oils, can not offer the characteristics ones above. Consult your Poclain Hydraulics sales engineer.
7 1
1 2
H
3 1 2
P
3 4 1 2
S
3 4 5 6
4
1 2
D
3
M 2 4W
4
Torque Torque
Dynamic
Static
16 600 Nm [12 240 lb .ft]120 bar [1 740 PSI]22 cm³ [1.34 cu.in]4 L/min [1.06 GPM]
9 580 Nm [7 070 lb .ft]7 660 Nm [5 650 lb .ft]6 830 Nm [5 040 lb .ft]
30 bar [435 PSI]86 cm³ [5.25 cu.in]
14 bar [203 PSI]8 000 Nm [5 900 lb .ft]
882 kJ
7 7 3 1Hydraulically controlled dynamic brakingMax. permissible brake torquePressure to obtain max. permissible brake torqueVolume required for brakingMini. irrigation flow rate for dynamic brakingHydraulically controlled parking brakeParking brake torque (new brakes)Parking brake torque (after 500 dynamic braking)Parking brake torque mini. requiring renovationMax. release brake pressureVolume for brake releaseInlet conditions for brake release in towing (Flow rate of 2 L/min)Emergency dynamical braking torque at 0 bar to the caseMax. energy dissipation
Indicative values coming from fly-wheel test bench. Braking performance must be performed on machine by the manufacturer.
Hydraulic motors MW24 POCLAIN HYDRAULICS
12 08/01/2013
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 13
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
OPTIONS
You can accumulate more than one optional part. Consult your Poclain Hydraulics sales engineer.
M 2 4 7 1W
1 2
H
3 1 2
D
3 1 2
P
3 4 1 2
S
3 4 5 6
4
1
2 - S - Q - 8 - Installed speed sensor or predisposition
Look at the "Mobile Electronic" N° A01889D technical catalogue for the sensor specifications and its connection.
To install the sensor, see the ''Installation guide'' brochure No. 801478197L.
Designation
T4 speed sensor (without rotation direction) 2TR speed sensor (digital rotation direction) STD speed sensor (two phase shifted frequencies) QPredisposition for speed sensor 8
A-A
Max. length Y=
Standard number of pulses per revolution=
13.4
60
MW24 POCLAIN HYDRAULICS
14 08/01/2013
POCLAIN HYDRAULICS Hydraulic motors MW24
08/01/2013 15
Op
tio
ns
Bra
keM
oto
rM
od
el c
od
e
08/01/2013
More information on
Poclain Hydraulics reserves the right to make any modifications it deems necessary to the products described in this document without prior notification.The information contained in this document must be confirmed by Poclain Hydraulics before any order is submitted.Illustrations are not binding.The Poclain Hydraulics brand is the property of Poclain Hydraulics S.A.
Thirteen subsidiaries and a worldwide network of more than 150 distributors and partners …
801 478 148H
A01875N
A01882V
A01883W
A01884X