MULTI-LEAF & SHUT-OFF DAMPERS Product Catalogue€¦ · Shut-off dampers/multi-leaf dampers can ......

MULTI-LEAF & SHUT-OFF DAMPERSProduct Catalogue

3

05

060708 - 09

10111213

1415 - 171819

Introduction

Square shut-off damper

Product description: square shut-off damperPrice listTest report according to DIN EN 1751

Square multi-leaf damper

Product description: square multi-leaf damperFJK 200 Price list and drawingFJK 300 Price listFJK 300 drawing and technical information

Circular shut-off damper

Product description: circular shut-off damperPrice list and drawing Installation and maintenance instructions TÜV test report

Table of contents

5

Shut-off dampers/multi-leaf dampers can be used as control, throttle or butterfly dampers to adjust pressure or flow settings in ventilation systems. They are often used to balance air duct systems to ensure the correct flow rates at junctions.

Square dampers basically consist of a C-shaped profiled frame into which the hollow body blades are built. These are connected to one another via a gear wheel. Circular dampers consist of a damper blade with internal blocks with sealing. Actuation of the damper blades or slats can be manu-ally adjusted on the flaps, differentiating, depending on the function, between an „OPEN/CLOSE“ function or step less adjust-ment in a range from 0° - 90° or an actuator can be used.

The supply duct can be directly connected via a flange.

The design of our dampers means there are no metal parts within the air stream, which creates a high degree of leak tightness for a shut-off damper.

Our specialisms:

TÜV certified in compliance with DIN EN1751 class 4 and DIN1946 part 4

Multi-leaf dampers/Shut-off dampers

6

The shut-off damper meets the require-ments for leak tightness in compliance with the following standards:- DIN EN 1751, class 4 - DIN 1946, part 4

Tested operating conditions: temperature: max. 40°C system pressure: max. +/- 2000 Pa

Shut-off dampers can be used as regulat-ing and shut-off valves to adjust volumet-ric flow rates in ventilation systems.

The design of our dampers means there are no metal parts inside the air stream. This design produces a high degree of leak tightness.

The airtight shut-off damper is mainly used within the chemical industry, in medical clean rooms or in the electroplating sec-tor as the dampers can be used to close off individual areas. They can therefore be used to close off an air line, for example, to avoid the influx of cold air during plant standstill.

Operation of the shut-off damper is done by means of a continuous protected square shaft made from V2A. In the standard ver-sion, the damper is provided with lockable levers for manual setting or with a console for an electrical actuator.

Square shut-off damper „airtight“

Technical information:

Blades

Gear wheels

Power transmission

Casing

Flange

counter rotating hollow body blades with lip seal, axle distance 165 mm

external plastic gear wheels, pro-tected by a cover

10 x 10 mm square axle of 1.4301 material, with an overhang on frame bracket

Length 300 mm

Flange width 40 mm,undrilled S=10 mm, measured on the outside of the casing

7

When ordering please include the corresponding part numbers: FAK, then material e.g. PP, then width e.g. 500, then height e.g. 835>>>FAKPP500835: You can order directly from us using this item number.

When ordering please include the corresponding part numbers: FXAK, then width e.g. 600, then height e.g. 835, EL>>>FXAK600835EL: You can order directly from us using this item number.

Square shut-off damper (PPs, PP, PVC, PE)

Square shut-off damper (PPs-EL)

Pressure power/

Internal dimensions in mm <- Width in mm -> Net prices

Torque Blades Height 300 mm 400 mm 500 mm 600 mm 700 mm 800 mm 900 mm 1000 mm 1100 mm 1200 mm

1 175 mm - - - - - - - - - -

10 Nm 2 340 mm - - - - - - - - - -

3 505 mm - - - - - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

Pressure power/

Internal dimensions in mm <- Width in mm -> Net prices

Torque Blades Height 300 400 500 600 700 800 900 1000 1100 1200

1 175 mm - - - - - - - - - -

10 Nm 2 340 mm - - - - - - - - - -

3 505 mm - - - - - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

Price on request

Price on request

8

Task: Damper test by TÜV SÜD Date: 09/02/2012

Unit: 500 x 500 mm shut-off damper Examiner: Mr Schweizer

Test facility: ZUBER GmbH / 88167 Röthenbach

Test area 0,25 m²

Classification of leakage with closed damper blade in compliance with DIN EN 1751

Comments/evaluation:The requirements and the criterion for the „air tight“ type damperwere fulfilled in compliance with DIN EN 1751, class 4.

Test report in compliance with DIN EN 1751

Test pressure in pascal

Counter rea-ding START*

Counter rea-ding STOP*

Leak volume in l/min

Leak flow rate l/(s*m²)

200 39.850 39.874 24 1,6

500 39.970 40.016 46 3,06

1000 40.230 40.294 64 4,3

1500 40.400 40.480 80 5,3

2000 40.590 40.690 100 6,67

9

Examination at the test facilityIn order to guarantee on-going high qual-ity, the multi-leaf dampers are tested at our own TÜV-approved test facility and regu-larly checked for airtightness.

10

Multi-leaf dampers are used to regulate the volumetric air flow and pressure and to shut off line cross sections in air condition-ing systems. The dampers essentially con-sist of a C-shaped profiled frame into which the blades are fitted.

The design of our dampers means there is no need to have any metal parts inside the air flow.

The shut-off damper is operated using a fully protected square shaft made of V2A.

In the standard version, the damper is supplied with a lockable lever for manual setting or with a console for electric actua-tion.

Dampers consist of several rotatable hollow body blades, embedded in plas-tic bushings and designed to optimise through flow. The hollow body blades are activated via external, plastic covered gear wheels designed to rotate with the help of a square shaft in the opposite direction to the blades.

It is mounted in the ventilation system us-ing lead frames (flange connection).

Square multi-leaf damper

Operating conditions: temperature: max. 40 ° C. system pressure: max. +/- 2000 Pa


Blades

Gear wheels

Power transmission

Casing

Flange

opposite hollow body blades,100 mm centre distance

Externalplastic gear wheels, pro-tected by a cover

10 x 10 mm square axle made of 1.4301 material, with an overhang on frame bracket

Length 200 mm

Flange width 40 mm,undrilled S=10 mm, measured on the outside of the casing

11

When ordering please include the corresponding part numbers: FAK, then material e.g. PP, then width e.g. 400, then height e.g. 210>>>FXAK600835EL: You can use this item number to order directly from us.

When ordering please include the corresponding part numbers: FXAK, then width e.g. 700, then height e.g. 835, EL>>>FXAK600835EL: You can use this item number to order directly from us.

Square multi-leaf damper (PPs, PP, PVC, PE)Blade height 100 mm

FJK 200 Square multi-leaf damper (PPs-EL)Blade height 100 mm

Technical Drawing 200 FJK

Pulling load/ Internal dimensions <- Width in mm -> Net prices

Torque Blades Height (mm) 200 300 400 500 600

10 Nm 1 110 mm - - - - -

10 Nm 2 210 mm - - - - -

10 Nm 3 310 mm - - - - -

10 Nm 4 410 mm - - - - -

10 Nm 5 510 mm - - - - -

Pulling load/ Internal dimensions <- Width in mm -> Net prices

Torque Blades Height (mm) 200 300 400 500 600

10 Nm 1 110 mm - - - - -

10 Nm 2 210 mm - - - - -

10 Nm 3 310 mm - - - - -

10 Nm 4 410 mm - - - - -

10 Nm 5 510 mm - - - - -

B

H

200

Price on request

Price on request

12

When ordering please include the corresponding part numbers: FJK, then material e.g. PP, then width e.g. 400, then height e.g. 210 >>>FJKPP400210: You can use this item number to order directly from us.

When ordering please include the corresponding part numbers: FXJK, then width e.g. 700, then height e.g. 835, >>>FXJK700835EL: Using this item number, you can order directly from us.

The „S“ indicates a damper actuator with a built-in auxiliary switch.

Pulling load/ internal dimensions in mm <- Width in mm -> Net prices


1 175 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

10 Nm 2 340 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

3 505 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

We can offer the following Belimo brand motors for the dampers:

Pressure power/torque: 10 Nm

NM24A 102,00 € netNM24A-S 123,00 € netNM230A 105,00 € netNM230A-S 127,50 € net

Pressure power/torque: 20 Nm

SM24A 117,00 € netSM24A-S 147,00 € netSM230A 120,00 € netSM230A-S 150,00 € net

Square multi-leaf damper (PPs, PP, PVC, PE)Blade height 165 mm

FJK 300 Square multi-leaf damper (PPs-EL)Blade height 165 mm



1 175 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -


3 505 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

Price on request

Price on request

13



1 175 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -


3 505 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

Technical Drawing 300 FJK



1 175 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -


3 505 mm FJK 200 FJK 200 FJK 200 FJK 200 - - - - - -

4 670 mm - - - - - - - - - -

20 Nm 5 835 mm - - - - - - - - - -

6 1000 mm - - - - - - - - - -

7 1185 mm - - - - - - - - - -

10 Nm 8 1350 mm - - - - - - - - - -

9 1515 mm - - - - - - - - - -

10 1680 mm - - - - - - - - - -

20 Nm 11 1845 mm - - - - - - - - - -

12 2010 mm - - - - - - - - - -

300B

H


Blades

Gear wheels

Power transmission

Casing

Flange

Counter rotating hollow body blades, centre distance 165 mm

external plastic gear wheels, pro-tected by a cover

10x10 mm square axle made of 1.4301 material, with an overhang on frame bracket

Length 300 mm

Flange width of 40 mm, drilled S=10 mm measured on the outside of the casing

14

Shut-off dampers can be used for volumet-ric flow setting, regulation and flow valves in ventilation systems.

They can be operated either manually or using an actuator, which, depending on the application, operates an „ON/OFF“ function or continuous adjustment in the range of 0° to 90°.

Circular „airtight“ shut-off dampers consist of a rotatable damper blade mounted in plastic bushings. This is sealed with a rub-ber lip seal toward the damper casing. The casing consists of a tube with flanges or sleeves.

The design of our dampers means there are no metal parts inside the air stream. The design also ensures a tight seal is created.

The shut-off damper meets the require-ments for leak tightness in compliance with the following standards:- DIN EN 1751, class 4- DIN 1946, Part 4

Circular shut-off damper „airtight“

Tested Operating Conditions: temperature: max. 40°C.system pressure: max. +/- 2000 Pa

The damper is actuated using a continu-ous protected square shaft made of V2A. In the standard version the damper is sup-plied with a console for an electric actuator or with a lockable lever for manual adjust-ment.


Damper Blade

Actuator

Casing

welded with implementation ofsquare shaft

Square shaft throughout10x10 mm made of 1.4301 material, protruding over frame bracket

Reinforced tube with and stop-bar with sealing

15

When ordering please include the corresponding part numbers: FAKRF for circular shut-off damper withflange in PPS, plus diameter 200 >>>FAKRF200: using this item number you can order directly from us.

When ordering please include the corresponding part numbers: FAKRMPP for shut-off damper with sleeve in PP, plus diameter 200 >>> FAKRMPP200: Using this item number, you can order directly from us.

Length (mm)

Diameter (mm)

Square axle dimensions

(mm)

Net prices with flange Order No.: FAKRF

+ diameter

Net prices with sleeve Order No.: FAKRM +

diameter

Net prices with smooth ends Order No.: FAKR + diameter

200 110 10 x 10 - - not available with smooth ends





300 200 10 x 10 - - -

300 225 10 x 10 - - -

300 250 10 x 10 - - -

300 280 10 x 10 - - -

315 315 10 x 10 - - -

355 355 10 x 10 - - -

400 400 10 x 10 - - -

450 450 10 x 10 - - -

500 500 10 x 10 - - -

560 560 10 x 10 - - -

600 600 15 x 15 - - -

630 630 15 x 15 - - -

710 710 15 x 15 - - -

Length (mm)

Diameter (mm)


(mm)

Net prices with flange Order No.: FAKRFPP

+ diameter

Net prices with sleeve Order No.: FAKRMPP

+ diameter

Net prices with smooth ends Order No.: FAKRPP

+ diameter






300 200 10 x 10 - - -

300 225 10 x 10 - - -

300 250 10 x 10 - - -

300 280 10 x 10 - - -

315 315 10 x 10 - - -

355 355 10 x 10 - - -

400 400 10 x 10 - - -

450 450 10 x 10 - - -

500 500 10 x 10 - - -

560 560 10 x 10 - - -

600 600 15 x 15 - - -

630 630 15 x 15 - - -

710 710 15 x 15 - - -

Circular shut-off damper (PP material)

Circular shut-off damper (PP material)

Price on request

Price on request

16

When ordering please include the corresponding part numbers: FAKRFPE for circular shut-off damper with flange in PE, diameter plus 200 >>> FAKRFPE200: Using this item number, you can order directly from us.

When ordering please include the corresponding part numbers: FAKRMPP for shut-off damper with sleeve in PP, plus diameter 200 >>> FAKRMPP200: Using this item number, you can order directly from us.

Length (mm)

Diameter (mm)


(mm)

Net prices with flangeOrder No. FAKRFPE

+ diameter

Net prices with sleeve Order No. FAKRMPE

+ diameter

Net prices with smooth endsOrder No. FAKRPE

+ diameter






300 200 10 x 10 - - -

300 225 10 x 10 - - -

300 250 10 x 10 - - -

300 280 10 x 10 - - -

315 315 10 x 10 - - -

355 355 10 x 10 - - -

400 400 10 x 10 - - -

450 450 10 x 10 - - -

500 500 10 x 10 - - -

560 560 10 x 10 - - -

600 600 15 x 15 - - -

630 630 15 x 15 - - -

710 710 15 x 15 - - -

Length (mm)

Diameter (mm)


(mm)

Net prices with flange Order no.: FAKRFPVC +

diameter

Net prices with sleeve Order No. FAKRMPVC

+ diameter

Net prices with smooth endsOrder No. FAKRPVC

+ diameter






300 200 10 x 10 - - -

300 225 10 x 10 - - -

300 250 10 x 10 - - -

300 280 10 x 10 - - -

315 315 10 x 10 - - -

355 355 10 x 10 - - -

400 400 10 x 10 - - -

450 450 10 x 10 - - -

500 500 10 x 10 - - -

560 560 10 x 10 - - -

600 600 15 x 15 - - -

630 630 15 x 15 - - -

710 710 15 x 15 - - -

Circular shut-off damper (PE material)

Circular shut-off damper (PVC material)

Price on request

Price on request

17

When ordering please include the corresponding part numbers: FXAKR for circular shut-off damper with smooth ends in PPs-EL, plus diameter 200, EL>>>FXAK600835EL: Using this item number, you can order directly from us.

The „S“ indicates a damper actuator with a built-in auxiliary switch.

We can offer the following Belimo brand motors for the dampers:

Pressure power/torque: 5Nm(From d 110 to d 315):

LM24A 84,00 € net LM24A-S 96,00 € net LM230A 84,00 € net LM230A-S 96,00 € net

Pressure power/torque: 10 Nm(From d 355 to d 710):

NM24A 102,00 € net NM24A-S 123,00 € net NM230A 105,00 € net NM230A-S 127,50 € net

Circular shut-off damper (PPs-EL material)Length (mm)

Diameter (mm)


(mm)

Net prices with flangeOrder No. FXAKRF

+ diameter + EL

Net prices with sleeve Order No. FXAKRM

+ diameter + EL

Net prices with smooth endsOrder No. FXAKR+ diameter + EL




300 200 10 x 10 - - -

300 250 10 x 10 - - -

315 315 10 x 10 - - -

400 400 10 x 10 - - -

450 450 10 x 10 - - -

500 500 10 x 10 - - -

560 560 10 x 10 - - -

630 630 15 x 15 - - -

710 710 15 x 15 - - -

Technical Drawing Circular shut-off damper

Price on request

18

Please ensure the rectangular and tension-free mounting of the dampers without pres-sure loading.

The square dampers may only be installed with horizontal blades.

Before installation and after adjusting the flange bolts, the dampers must be checked for proper operation.

All dampers are maintenance-free and require no lubrication.

Assembly and maintenance instructions

19

TÜV test report For years, ZUBER has been manufacturing dampers that comply with DIN EN 1751, class 4 and DIN 1946, part 4

Zuber GmbHWigglis 8-1088167 Röthenbach

Telefon: +49 (0)8384 - 82 388 - 0Telefax: +49 (0)8384 - 82 388 - [email protected]

www.zuber-gmbh.com

MULTI-LEAF & SHUT-OFF DAMPERS Product Catalogue€¦ · Shut-off dampers/multi-leaf dampers can ......

Documents

Transcript of MULTI-LEAF & SHUT-OFF DAMPERS Product Catalogue€¦ · Shut-off dampers/multi-leaf dampers can ......