Multi Effect Evaporator Ppt
-
Upload
aradhana-kanchan -
Category
Documents
-
view
1.400 -
download
93
Transcript of Multi Effect Evaporator Ppt
![Page 1: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/1.jpg)
A PRESENTATION ON MULTIEFFECT EVAPORATOR FOR CONCENTRATING CAUSTIC SODA SOLUTION
PRESENTED BY : - ARADHANA
KANCHAN SUDHA
CHAUHAN MOHAMMAD
ANAS GAURAV SHUKLA
MUBASSHIR HASAN
![Page 2: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/2.jpg)
INTRODUCTION
A multiple-effect evaporator, as defined in chemical engineering, is an apparatus for efficiently using the heat from steam to evaporate water in a multiple-effect evaporator. Water is boiled in a sequence of vessels, each held at a lower pressure than the last. Because the boiling temperature of water decreases as pressure decreases, the vapor boiled off in one vessel can be used to heat the next, and only the first vessel (at the highest pressure) requires an external source of heat.
![Page 3: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/3.jpg)
The design of evaporators is generally taken to mean the determination of the heat transfer area and the steam consumption required to effect a specified separation at a specified set of steady-state operating conditions.
![Page 4: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/4.jpg)
Multiple effect evaporator used for concentration for caustic Soda solution
Holland investigated a triple effect evaporator (TEE) system used for the concentration of NaOH and computed the live steam consumption. The model was based on mass and energy balance equations which incorporated the effect of boiling point rise.Further, he considered three different values of overall heat transfer coefficient for the three different effects.
![Page 5: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/5.jpg)
edZain and Kumar (1996) investigated a TEE system, for the concentration of NaOH. They employed the empirical models for the consumption of OHTC and Boiling point rise for all the three effects.
![Page 6: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/6.jpg)
Modeling of Multiple effect evaporator systems
Assumption
Here We are describing the modeling equations for a triple effect evaporator system for the case where boiling point elevations are negligible. Also, the effect of composition on liquid enthalpy is neglected.
![Page 7: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/7.jpg)
![Page 8: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/8.jpg)
MODEL EQUATIONS
Effect no. 1
A Total Material Balance is given by:-
F = V1 + L1 ---- (1)
![Page 9: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/9.jpg)
An enthalpy balance on the process stream yields
Fhf + Q – V1 H1 – L1 h1 = 0
Since V1 = F – L1 , the previous equation can be rewritten as
F ( hf – h1 ) + Q – ( F – L1 ) ( H1 – h1 ) =
0 ----(2)
![Page 10: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/10.jpg)
Where Hj - hj=
λj
λj = The latent heat of vaporization of the solvent from the thick liquor at temperature T1 and pressure P1 ( j = 1 , 2, 3, the effect number )For the first effect, by Enthalpy balance on the steam, Q1 = Vo ( Ho – ho ) = λo ---- (3)
And the rate of heat transfer is given byQ1 = U1 A ( T0 - T1 ) ---- (4)
![Page 11: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/11.jpg)
By eliminating the value of Q by equation 3, equation 2 can be rewritten asF ( hf - h1 ) + Vo λo - ( F – L1) λ1 = 0 ---- (5)
The equation 4 and 5 may be stated in functional notation as follows
Enthalpy Balance f1 = F ( hf - h1 ) + Vo λo - ( F – L1 ) λ1 ----(6)Heat Transfer Ratef2 = U1 A ( To - T1) – Vo λ0
----(7)
![Page 12: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/12.jpg)
(Effect No. 2
By Enthalpy Balance on the steam,Q2 = ( F – L1 ) λ1 &The Rate of heat transfer Q2 = U2 A ( T1 - T2 ) Hence,
Enthalpy Balancef3 = L1 ( h1 – h2 ) + ( F – λ1 ) – ( L1 – L2 ) λ2
----(8)Heat Transfer ratef4 = U2 A ( T1 - T2 ) – ( F – L1 ) λ1
----(9)
![Page 13: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/13.jpg)
Effect no. 3
By Enthalpy Balance on steamQ3 = ( L1 - L2 ) λ2
The Rate of heat transfer, Q3 = U3 A ( T2 - T3)Hence,
Enthalpy Balancef5 = L2 ( h2 – h3 ) + ( L1 - L2) λ2 - ( L2 - L3 ) λ3
----(10)Heat transfer ratef6 = U3 A ( T2 - T3 ) – ( L1 - L2 ) λ2
----(11)
![Page 14: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/14.jpg)
sComponent Material Balance
The six independent equations can be solved for the six unknowns. In addition to these six independent equations, three additional equations that contain three additional independent variables x1 , x2, and x3 are given by
FX - Lj xj = 0, ( j = 1, 2, 3 ) ----(12)
![Page 15: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/15.jpg)
Use of the Newton – Raphson method for solving evaporator design problems
The Newton – Raphson method consists of the repeated use of the linear terms of the Taylor series expansions of the functions f1, f2, f3, f4, f5 and f6 [ eq (6) – eq (11) ] ,i.e,
0 = ∂f1 /∂V0 (∆V0) + ∂f1 / ∂T1 (∆T1) + ∂f1 /∂L1 (∆L1) + ∂f1 / ∂T2 (∆T2) + ∂f1 / ∂L2 (∆L2) + ∂f1 / ∂A (A) ----(13)
![Page 16: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/16.jpg)
,In equation 13,
∆V0 = Y0 , k+1 - Y0 , k
∆T1 = T1 , k+1 - T1 , k
∆T2 = T2 , k+1 - T2 , k
∆L1 = L1 , k+1 - L1 , k
∆L2 = L2, k+1 - L2 , k
∆A = Ak+1 - Ak
Where subscripts k and k+1 denote the kth and k+1st trials.
![Page 17: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/17.jpg)
fThese six equations may be stated in compact form by means of the following matrix equation
Jk ∆Xk = -fk ----(14)Where Jk is called the Jacobian Matrix and,∆Xk = Xk+1 - Xk = [ ∆V0, ∆T1, ∆L1, ∆T2, ∆L2, ∆A]T
The subscripts k and k+1 denote that elemt of the matrices carrying these subscripts are those given by the kth and k+1st trials, respectively.
![Page 18: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/18.jpg)
k∂f1/
∂VO
∂f1/
∂T1
∂f1/
∂L1
∂f1/
∂T2
∂f1/
∂L2
∂f1/A
∂f2/∂V0
∂f2/
∂T1
∂f2/∂L1
∂f2/∂T2
∂f2/
∂L2
∂f2/
∂A
…………….. …………………… ………………… ………………. ……………….. .....................
……………….. …………………… …………………. ………………… ………………... …………………
……………… ………………….. …………………. ………………… ………………… ......................
∂f6/∂V0
∂f6/
∂T1
∂f6/∂L1
∂f6/
∂T2
∂f6/
∂L2
∂f6/
∂A
The display of the elements os Jk
and fk is as follows:-
Jk= fk=
f1
f2
f3
f4
f5
f6
----(15)
![Page 19: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/19.jpg)
If the function f1, f2 , …. . , f6 and their partial derivatives which appear in Jk are continuous and the determinant of Jk is not equal to zero, then the Newton Raphson method will converge, provided a set of assumed values of the variables which are close enough to the solution set can be found .
![Page 20: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/20.jpg)
If the changes in the specific heats with temperature in the neighborhood of the solution to equation (6) through equation (11) are negligible, then the sensible heat terms (hf –h1), (h1 – h2), (h2 – h3) may be replaced by their respective equivalents; Cp (Tf – T1), Cp (T1 – T2), and Cp (T2 – T3). If the variation of the latent heats with temperature are also regarded as negligible in the neighborhood of the solution, then,
![Page 21: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/21.jpg)
λO -FCp ∂f1/∂L1
λ1 0 0
-λ0 -U1A o 0 0 U1 (To-T1)
0 L1Cp b33 -L1Cp - λ2 0
0 U2A λ1 -U2 A 0 U2 (T1-T2)
0 0 λ2 L2Cp b55 .0
0 0 -λ2 U3A λ2 U3 (T1–T3)
Jk =
----(16)
![Page 22: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/22.jpg)
Whereb33 = Cp (T1 – T2) - (λ1 + λ2)
b55 = Cp (T2 – T3) – (λ2 + λ3)
![Page 23: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/23.jpg)
Solution of a TEE problem by Newton- Raphson Method
We have to assume the value of following terms for the calculation procedure to design triple effect evaporator,1- (To- T1 ), (T1-T2 ) , and (T2-T3 )2- Solvent evaporated in first effect3- Solvent evaporated in second effect4- Solvent evaporated in third effect L3 can be calculated by component material balance equation (12), asL3 = FX / x3
5- Area, A6- Vo , Vapour flow rate of steam
![Page 24: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/24.jpg)
The following scaling procedure should be used…1- Each functional equation is divided by the product Fλo, and the new functional expression so obtained are denoted by gj (j = 1, 2, ……, 6)
g j = fj / F λo
2- All flow rates are expressed as a function of the feed rate F, that is Lj = lj F and Vj = vj F.
3- All the temperatures are expressed as a function of the steam temperature as follows; Tj = uj To, which defines the fractional temperature uj.
![Page 25: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/25.jpg)
4- The area of each effect is expressed as a fraction of a term proportional to the flow rate in the following manner;-
Aj = aj ( F / 50 ), which defines the fractional area aj.
After this scaling procedure has been applied to the functional expressions, the matrices Jk, ∆Xk, nd fk take the following terms;-
![Page 26: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/26.jpg)
1 b12 λ1 / λ0 0 0 0
-1 b22 0 0 0 b26
0 b32 b33 b44 λ2 / λ0 0
0 b42 λ1 / λ0 b44 0 b46
0 0 λ1 / λ0 b54 b55 0
0 0 λ1 / λ0 b64 λ2 / λ0 b66
![Page 27: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/27.jpg)
a∆Xk = [ ∆vo ∆u1 ∆l1 ∆u2 ∆l2 ∆a ]T
fk = [ g1 g2 g3 g4 g5 g6 ]T
Where the elements of Jk consist of the partial derivatives of the gj’s with respect to the new set of variables ( vo, u1, l1, u2, l2, a)
b12 = -Cp To / λo , b34 = -l1 Cp To / λ0 ,
b22= -U1 a To / 50 λ0 ,
b44 = U2 a To / 50 λ0 , b32= l1 Cp T0 / λ0 , b54 = l2 Cp T0 / λ0 , b42 = U2 a To / 50 λ0 ,
![Page 28: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/28.jpg)
b64 = U3 a T0 / 50 λo,
b26 = [ U1 ( 1 -u1 )To ] / 50 λo,
b33 = [ Cp ( u 1- u2 ) To - ( λ1+λ2 )] / λo,
b46 = [ U2 ( u1 - u2 ) To ] / 50 λo,
b55 = [ Cp ( u2 - u3 )To - ( λ2 + λ3 ) ] / λo,
b66 = [ U3 ( u2 - u3 ) To ] / 50 λo
![Page 29: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/29.jpg)
Then on the basis of the assumed values of the variables the matrices J0, Xo, f0 are used in the first trial. Convergence to within about six significant numbers is achieved in further trials. We get the value of v0, , u1, l1,
u2, l2, Thus, the desired solution is. V0 = vo F, T1 = u1 To, L1 = l1 F, L2 = l2 F,
A = a F / 50 , L3 = F X / x3, x1 = F X / L1
&
X2 = F X / L2
![Page 30: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/30.jpg)
Nomenclature
F = feed rate, kg / hr;
Lj = Thick liquor rate, kg / hr, ( where j= 1, 2, 3 for first, second and third effect respectively );
Vj = Vapor rate, kg / hr, ( where j= 1, 2, 3 for first, second and third effect respectively );
X = Mass fraction of the solute in the feed;
x = Mass fraction of the solute in the thick liquor;
![Page 31: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/31.jpg)
hf = Enthalpy of the feed, kJ / kg;
hj = Enthalpy of the thick liquor at the boiling point temperature of the evaporator , kJ / kg; for first, second and third effect respectively;
Hj = Enthalpy of the vapor at the boiling point of the evaporator, kJ / kg; for first, second and third effect respectively;
Qj = Rate of heat transfer across the tubes( from the steam to the thick liquour ), kJ / hr; for the first, second and third effect respectively
![Page 32: Multi Effect Evaporator Ppt](https://reader036.fdocuments.us/reader036/viewer/2022081414/55351c8e5503464c148b465e/html5/thumbnails/32.jpg)