Muk3D Training Courses 2019downloads.minebridgesoftware.com/training/Muk3D_Training_Brisba… ·...
4
MineBridge Software Inc. 2019 1 Muk3D Training Courses - 2019 Where: Brisbane, Australia Locaon TBA When: 3rd June 2019 Introducon to Muk3D Formaon 4th June 2019 Tailings planning with Muk3D Tailings+ 5th June 2019 Macros and scripng with Muk3D Cost: $600 AUD for 1 day $1000 AUD for 2 days $1300 AUD for 3 days 2 or more aendees from the same organisaon will get a 15% discount Requirements: Users must have their own laptop with Muk3D installed. Temporary licenses and soſtware downloads will be provided before the course. All parcipants will receive comprehensive training notes and training data. Lunch and refreshments will be provided. Please advise of any dietary or allergy concerns at the me of registraon. To book your place please contact your MineBridge Soſtware representave, or email us at [email protected].
Transcript of Muk3D Training Courses 2019downloads.minebridgesoftware.com/training/Muk3D_Training_Brisba… ·...
MineBridge Software Inc. 2019
1
Muk3D Training Courses - 2019
Where: Brisbane, Australia Location TBA
When: 3rd June 2019 Introduction to Muk3D Formation
4th June 2019 Tailings planning with Muk3D Tailings+
5th June 2019 Macros and scripting with Muk3D
Cost: $600 AUD for 1 day
$1000 AUD for 2 days
$1300 AUD for 3 days
2 or more attendees from the same organisation will
get a 15% discount
Requirements: Users must have their own laptop with Muk3D installed. Temporary licenses and
software downloads will be provided before the course.
All participants will receive comprehensive training notes and training data.
Lunch and refreshments will be provided. Please advise of any dietary or allergy
concerns at the time of registration.
To book your place please contact your MineBridge Software representative, or
email us at [email protected].
MineBridge Software Inc. 2019
2
Introduction to Muk3D Formation
Introduction to Muk3D Formation for simple 3D modeling. This session will focus on the basic 3D tools
available in Muk3D Formation that are aimed at basic geotechnical, mining, and surface water management
tasks. A series of simple design tasks will be tackled using our training datasets.
• Importing data.
• Creating surfaces and grids.
• Basic structure creation.
• Creating and manipulating polylines
• Volumetrics.
• Importing, using, and manipulating aerial
photography.
• Exporting data.
• Watershed analysis.
• Dam zonation modelling.
• Simple waste dump modelling.
• Strategies for importing huge datasets.
• An introduction to macros.
Course duration
The course is 1 day long, with lunch and refreshment breaks.
Who is it suitable for?
• New users of Muk3D.
• Existing users of Muk3D who want to sharpen their modelling skills.
• Engineers and designers who routinely work with 3D data.
• Project managers who want to better understand the modelling capabilities of their staff.
What will you learn?
Prerequisites
This course assumes no prior 3d modelling experience.
MineBridge Software Inc. 2019
3
Tailings planning with Muk3D Tailings+
This course is aimed at giving participants an understanding of how to create tailings plans using Muk3D
Tailings+. It will start with explaining the deposition models, and inputs required, and then run through
conceptual layouts, and long range planning.
• Defining tailings properties
• Preparation of survey surfaces for tailings
modelling.
• Conceptual layout of various TSF options.
• TSF capacity calculations
• Understanding different deposition and pond
models within Muk3d
• Starter dam sizing.
• Development of long range tailings plans.
• Presentation of tailings plans.
• Modelling of different tailings technologies
(conventional/thickened/dry stack)
• Integration with water balance plans.
Course duration
The course is 1 day long, with lunch and refreshment breaks.
Who is it suitable for?
• New users of Muk3D.
• Existing users of Muk3D who want to sharpen their modelling skills.
• Engineers and designers who need to develop tailings plans, or evaluate tailings facility/technology
options from a volumetric viewpoint..
• Project managers who want to better understand the modelling capabilities of their staff.
What will you learn?
Prerequisites
This course assumes that users have a good understanding of the design tools in Muk3D, either from
participating in the Formation training course, or through previous use of Muk3D. Users are also
expected to have a basic understanding of tailings planning.
MineBridge Software Inc. 2019
4
Macros and scripting with Muk3D
This session is an introduction to macros and scripting with Python in Muk3D. Python is a high-level language
that allows users to customise and automate aspects of Muk3D to simplify repetitive design tasks and
automate workflows.
• Importing and manipulation of text files.
• Importing large/tiled datasets.
• Creating structures procedurally.
• Creating simple user interfaces and
interacting with data in the 3D window.
• Automation of a simple tailings plan.
• Post-processing of tailings plan runs.
Course duration
The course is 1 day long, with lunch and refreshment breaks.
Who is it suitable for?
• Experienced users of Muk3D who are interested in automating repetitive tasks.
• New users of Muk3D who have a background in scripting/programming.
• Muk3D users who are interested in creating their own custom functionality.
What will you learn?
Prerequisites
This course assumes that users have a good understanding of the design tools in Muk3D, either from
participating in Muk3D training courses, or from practical experience with Muk3D.
There is no expectation that the participants know Python, but having a basic understanding of
programming concepts, or previous experience with scripting/programming (e.g. VBA macros etc) will be
an advantage.
Additional requirements Participants are required to have an appropriate text editor installed on their computer. Windows
Notepad is not acceptable. We recommend Notepad++ (notepad-plus-plus.org)
