mounting instructionsKLINGER Spiral-Wound Gaskets Type CRIR Type CRIR/ PTFE inner ring Type CRIR/...

Summary of the eight versions of KLINGER SWGs, the designprinciple,materialsand mountinginstructions.

KLINGER

Spiral Wound Gaskets

KLINGERmaxiflex mounting instructions

The principleThe KLINGERmaxiflex function isbased on the metal winding/ filler re-lationship and the flange surfaces.

The surface roughness should beapprox. Ra 3.2 µm. KLINGERmaxiflexgaskets can be used in flanges withlarger surface roughnesses, but in thiscase the bolt loads should be increa-sed so as to ensure proper function ofthe gasket.

When the KLINGERmaxiflex gas-ket is compressed during mounting,the homogeneous filler „flows“ intothe irregularities of the flange. Themetal windings enclose the filler and,at the same time, ensure the strengthand elasticity of the gasket.

If the gasket is equipped with anPTFE filler it must have an inner ringsince the PTFE permits no furthercompression, as is the case with otherfillers. On the one hand, it preventsthe gasket from springing open andon the other, penetration of the flo-wing PTFE in the pipeline. The largerthe surface roughnesses in the flangesurface, the larger the surface loadrequired to permit a flow of the PTFEin the irregularities.

MountingThe bolts should be free of damageand lubricated with high-temperatureresistant greases before mounting.

Insert the gasket and fasten boltsfinger-tight.

Next, tighten the bolts crosswise(see sketch) in at least 3 to 4 passes.The more passes you perform, themore uniform the force which is intro-duced into the flange-gasket system.

In the last pass, the bolts must betightened only clockwise.

1

2

34

7 5

86

All information is provided inaccordance with the current state ofknowledge. As we cannot influence thespecific application conditions, wewould ask you to consider this as anon-binding recommendation.

We can assume no liability for anyresulting damage.

We reserve the right to technicalmodifications.

MountingFlange surface condition:1. metallically clean2. plane-parallel3. dry4. fat freeDo not use separating agents or sealing aids!

Certified Fire Safe According to API 6FB!

Wide choice of materials for metal strip and filler. Suitable for high pressures and temperatures.Recommended for flanges with tongue and groove.

Type R

Solid metal outer ring used as a centerring device and compressionstop.Used on raised face and flat face flanges.

Type CR

Solid metal inner ring.Use with high pressures and temperatures.Male to female flanges.

Type RIR

This gives the gasket recoveryforces which provide for a reliablesurface load even at fluctuating oper-ating conditions.

In the present 8 versions, thebasic element is added by innerand/or outer rings as needed.

Standard Metal strip materials Gasket thicknessesNominalthickness3.2 mm4.5 mm7.2 mm

Compressed Guide ringthickness thickness2.3 - 2.5 mm 2 - 2.2 mm3.2 - 3.4 mm 3 - 3.3 mm5.0 - 5.5 mm 5 - 5.5 mm

The design principle of theKLINGER Spiral-Wound GasketsThe basic element of every gasket isthe wound core. The V-shaped metalstrip is spirally wound with the soft-material filler.

To improve the mechanicalstrength and other sealing character-istics, some layers at the beginningand at the end are wound without softmaterial and spot-welded over thetotal circumference.

The constant tensile force duringthe complete winding process permitsa defined, constant thickness of thestructure.

1.43011.44011.44041.45411.4571Special version:Monel 400 ®, InConel 600 ®, InConel 625 ®, InConel X750 ®,Nickel 200 ®, Titanium, Incoloy 800 ®, Incoloy 825 ®

Other materials on request

304316316 L321316 Ti

Solid metal outer and inner rings.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Prevents turbulences and protects the flanges from erosion.Protects the inner windings of thegasket element from high temperatures.

Solid metal outer ring, PTFE innerring.Suitable for raised face or flat faceflanges.PTFE inner ring acts as an additionalgasket and protects the inner windingsof the gasket element from the fluid.

Solid metal inner ring with KLINGER-graphite facing.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Suitable for corrosive media.Graphite inner ring acts as an additional gasket.

Fillers and temperature limits CeramicsKLINGERgraphite*PTFENonas*pure graphite standard 98% purity or 99.85% nuclear grade

approx. 800°Capprox. 600°Capprox. 260°Capprox. 460°C

Standard materials outer ringCarbon steel,colour-powder coatedStainless steelacc. to the standard metal strip materials

Standard materials inner ringStainless steelacc. to the standard metal strip materials

KLINGERmaxiflex spiral-wound gaskets

KLINGERSpiral-Wound Gaskets

Type CRIR Type CRIR/PTFE inner ring

Type CRIR/KLINGERgraphite inner ring

Wide choice of materials for metal strip and filler. Suitable for high pressures and temperatures.Recommended for flanges with tongue and groove.

Type R

Solid metal outer ring used as a centerring device and compressionstop.Used on raised face and flat face flanges.

Type CR

Solid metal inner ring.Use with high pressures and temperatures.Male to female flanges.

Type RIR

This gives the gasket recoveryforces which provide for a reliablesurface load even at fluctuating oper-ating conditions.

In the present 8 versions, thebasic element is added by innerand/or outer rings as needed.

Standard Metal strip materials Gasket thicknessesNom.gasket thickness3.2 mm4.5 mm7.2 mm

Recommended thickness in loaded condition2.3 – 2.5 mm3.2 – 3.4 mm4.8 – 5.0 mm

The design principle of theKLINGERmaxiflex spiral-wound gasketsThe basic element of every gasket isthe wound core. The V-shaped metalstrip is spirally wound with the soft-material filler.

To improve the mechanicalstrength and other sealing character-istics, some layers at the beginningand at the end are wound without softmaterial and spot-welded over thetotal circumference.

The constant tensile force duringthe complete winding process permitsa defined, constant thickness of thestructure.

1.43011.44011.44041.45411.4571Special version:Monel 400 ®, InConel 600 ®, InConel 625 ®, InConel X750 ®,Nickel 200 ®, Titanium, Incoloy 800 ®, Incoloy 825 ®

Other materials on request

304316316 L321316 Ti

Solid metal outer and inner rings.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Prevents turbulences and protects the flanges from erosion.Protects the inner windings of thegasket element from high temperatures.

Solid metal outer ring, PTFE innerring.Suitable for raised face or flat faceflanges.PTFE inner ring acts as an additionalgasket and protects the inner windingsof the gasket element from the fluid.

Solid metal inner ring with KLINGER-graphite facing.For use at high pressures and temperatures.Suitable for raised face or flat faceflanges.Suitable for corrosive media.Graphite inner ring acts as an additional gasket.

Fillers and temperature limits CeramicsKLINGERgraphite*PTFEMica*pure graphite standard 98% purity or 99.85% nuclear grade

approx. 800°Capprox. 500°Capprox. 260°Capprox. 900°C

Standard materials outer ringCarbon steel,colour-powder coatedStainless steelacc. to the standard metal strip materials

Standard materials inner ringStainless steelacc. to the standard metal strip materials

KLINGER Spiral-Wound Gaskets

KLINGERmaxiflex spiral-wound gaskets

Type CRIR Type CRIR/PTFE inner ring

Type CRIR/KLINGERgraphite inner ring

KLINGERSpiral-Wound Gaskets

Spiral wound sealing element. Wound high density.Wide choice of materials for metalstrip and filler material.For use in high-pressure pumps,high-pressure valves and gas applications.Low emission tested.

Type RHD

KLINGERgraphite facing 0.5 mm.For use in manhole gaskets.Suitable for use with low bolt loadsand uneven gasket surfaces.Double sealing effect.

Type R withKLINGERgraphite facing

Combined inner and outer rings.The inner ring could have pass barsor could carry either a metal clad orsoft gasket with pass bars.

Type HTX forheat exchan-gers

Recommended sealing strip roughnessThese gaskets are capable of givingan excellent seal over a wide range offlange surface finishes.

Subject to technical alterations. Status: April 1999

general critical vacuum

Ra micrometer3.2 – 5.13.22.0

(Larger flange surface finishes requirehigher bolt loads)

However, as a general guide werecommend the following:

PN10–4036404754657084102115140168196221251307358405458566666770874974

1,0781,2801,5101,7201,9202,1202,3302,5302,7302,9303,130

PN 64–32036404754657084104119144172200227257315366413466574674778882982

1,0861,290

–––––––––

d410465161718292

107127142162192217247272327377437488593695810917

1,0171,1241,3411,5481,7721,9722,1822,3842,5942,7943,0143,228

d3d210–320

242833404954668295120146174195225286337382433537637737837930

1,0301,2301,4501,6601,8602,0502,2602,4602,6602,8603,060

KLINGERmaxiflextypes CR, CRIR

Suitable for flanges in accordance with DIN and BS 4504,measures in mm

DN

101520253240506580100125150175200250300350400500600700800900

1,0001,2001,4001,6001,8002,0002,2002,4002,6002,8003,000

d110–320

182227344348577386

108134162183213267318363414518618718818910

1,0101,2101,4201,6301,8302,0202,2302,4302,6302,8303,030

16465161718292

107127142162192217247272328383443495617734804911

1,0111,1281,3421,5421,7641,9642,1682,378

––––

25465161718292

107127142167193223253283340400457514624731833942

1,0421,1541,3641,5781,7982,0002,230

–––––

40465161718292

107127142167193223265290352417474546628747852974

1,0841,1941,3981,6181,830

–––––––

645661748290

102112137147173210247277309364424486543657764879988

1,1081,2201,452

–––––––––

1005661748290

102118143153180217257287324391458512572704813

––––––––––––––

1605661748290

102118143153180217257284324388458––––––––––––––––––

25067727982100108123153170202242284316358442538––––––––––––––––––

d2d3d4

d4

d1d2d3

CR CRIR

Summary of the eight versions of KLINGERmaxiflex, the designprinciple,materialsand mount-ing instructions.

KLINGER-maxiflex

spiral-wound gaskets

Mounting Instructions

The principleThe spiral wound function isbased on the metal winding/ filler re-lationship and the flange surfaces.

The surface roughness should beapprox. Ra 3.2 µm. These gasketscan be used in flanges with largersurface roughnesses, but in thiscase the bolt loads should be increased so as to ensure proper function of the gasket.

When the gasket iscompressed during mounting,the homogeneous filler „flows“ intothe irregularities of the flange. Themetal windings enclose the filler and,at the same time, ensure the strengthand elasticity of the gasket.

If the gasket is equipped with aPTFE filler it must have an inner ringsince the PTFE permits no furthercompression, as is the case with otherfillers. On the one hand, it preventsthe gasket from springing open andon the other, penetration of the flo-wing PTFE in the pipeline. The largerthe surface roughnesses in the flangesurface, the larger the surface loadrequired to permit a flow of the PTFEin the irregularities.

MountingThe bolts should be free of damageand lubricated with high-temperatureresistant greases before mounting.

Insert the gasket and fasten boltsfinger-tight.

Next, tighten the bolts crosswise(see sketch) in at least 3 to 4 passes.The more passes you perform, themore uniform the force which is intro-duced into the flange-gasket system.

In the last pass, the bolts must betightened only clockwise.

1

2

34

7 5

86

All information is provided inaccordance with the current state ofknowledge. As we cannot influence thespecific application conditions, wewould ask you to consider this as anon-binding recommendation.

We can assume no liability for anyresulting damage.

KLINGER reserve the right to technical modifications.

MountingFlange surface condition:1. metallically clean2. plane-parallel3. dry4. fat freeDo not use separating agents or sealing aids!

d2d3d4

d4

d1d2d3

CR CRIR

10 –320

d110 –320

d2PN 10 –

40

d3PN 64 –

32010 16 25 40 64

d4100 160 250

DN

Subject to technical alterations.Status: April 1999

Certified according to DIN EN ISO 9001.

KLINGER SWGtypes CR/CRIR

Suitable for flanges in accordance with DIN and BS 4504,measures in mm

d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

Subject to technical alterations.Status: October 2000


KLINGER GmbHP.O. Box 1370, D-65503 IdsteinRich.-Klinger-Straße, D-65510 IdsteinTel +49 (0) 61 26 950-0Fax +49 (0) 61 26 950 340/341e-mail: [email protected]://www.klinger-gmbh.de



150300400600

9001,5002,500

150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500

øA ofsealing elem.

øIof sealing element

øAof centering ring

d3 d2 d4No

min

al w

idth

Pressure stage [lbs] Pressure stage [lbs]Press. st. [lbs]


Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in inch

Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in mm

KLINGERmaxiflextypes CR/CRIR

150300400600

9001,5002,500

150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500

øA ofsealing elem.



d3 d2 d4

Nom

inal

wid

th


d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206






150300400600

9001,5002,500

150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500

øA ofsealing elem.



d3 d2 d4

Nom

inal

wid

th



Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in inch

Gaskets in accordance with ASME B 16.20, flanges according ANSI B 16.5, measures in mm


150300400600

9001,5002,500

150 300 400 600 900 1,500 2,500 150 300 400 600 900 1,500 2,500

øA ofsealing elem.



d3 d2 d4No

min

al w

idth


Inner-Ring Inside Diameters for Spiral-Wound Gaskets for Use With ASME B16.5 Flanges (as per ASME B16.20-2007 Standard's Table 12) Flange Pressure Class

Size (NPS) 150 300 400(Note 1) 600 900(Note 1) 1500 2500(note1)

1/2 14.2 14.2 14.2 14.2 14.2 14.2 14.2 3/4 20.6 20.6 20.6 20.6 20.6 20.6 20.6 1 26.9 26.9 26.9 26.9 26.9 26.9 26.9

1 1/4 38.1 38.1 38.1 38.1 33.3 33.3 33.3 1 1/2 44.5 44.5 44.5 44.5 41.4 41.4 41.4

2 55.6 55.6 55.6 55.6 52.3 52.3 52.3 2 1/2 66.5 66.5 66.5 66.5 63.5 63.5 63.5

3 81.0 81.0 81.0 81.0 78.7 78.7 78.7 4 106.4 106.4 102.6 102.6 102.6 97.8 97.8 5 131.8 131.8 128.3 128.3 128.3 124.5 124.5 6 157.2 157.2 154.9 154.9 154.9 147.3 147.3 8 215.9 215.9 205.7 205.7 196.9 196.9 196.9

10 268.2 268.2 255.3 255.3 246.1 246.1 246.1 12 317.5 317.5 307.3 307.3 292.1 292.1 292.1 14 349.3 349.3 342.9 342.9 320.8 320.8 … 16 400.1 400.1 389.9 389.9 374.7 368.3 … 18 449.3 449.3 438.2 438.2 425.5 425.5 … 20 500.1 500.1 489.0 489.0 482.6 476.3 … 24 603.3 603.3 590.6 590.6 590.6 577.9 …

Note 1: (1) There are no NPS 1/2 through NPS 3 Class 400 flanges (use Class 600) , NPS 1/2 through NPS 2 1/2 Class 900 flanges (use Class 1500), or NPS 14 and larger Class 2500 flanges.

subject to technical alterations. status: Oct'10

d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

øI øI øA øAøI øI øA øAøI øI øA øAøI øI øA øA

Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Sealing element

Cen-teringring

Innerring

Pressure stage [lbs]150




d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4


Large flanges in accordance with API 605, measures in inch

Nom

inal

wid

th

Subject to technical alterations.Status: 1995






Large flanges in accordance with MSS SP 44, measures in inch


Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Sealing element

Cen-teringring

Innerring






Nom

inal

wid

th

d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206


Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Sealing element

Cen-teringring

Innerring







Large flanges in accordance with API 605, measures in inch

Nom

inal

wid

th







Large flanges in accordance with MSS SP 44, measures in inch


Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Innerring

Sealing element

Cen-teringring

Sealing element

Cen-teringring

Innerring





d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4 d1 d2 d3 d4No

min

al w

idth


P. s. [lbs] 300 bis 1500 300 400 600 900


o/I o/I o/A o/A o/I o/A o/A o/I o/A o/A

Innerring

Sealingelement

Cente-ringring

Sealingelement

Centering ring Sealingelement

Cente-ringring

d1

[inch]

d2 d3 d4 d2 d3 d4 d2 d3 d4

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

Nom

inal

wid

th

d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

Pressure stage [lbs]






Flanges in accordance with BS 3381, ANSI B 16.5,measures in inch



P. s. [lbs] 300 bis 1500 300 400 600 900



Innerring

Sealingelement

Cente-ringring

Sealingelement


Cente-ringring

d1

[inch]

d2 d3 d4 d2 d3 d4 d2 d3 d4

Nom

inal

wid

th


Flanges in accordance with BS 3381, ANSI B 16.5,measures in mm



P. s. [lbs] 300 bis 1500 300 400 600 900



Innerring

Sealingelement

Cente-ringring

Sealingelement


Cente-ringring

d1

[inch]

d2 d3 d4 d2 d3 d4 d2 d3 d4

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

Nom

inal

wid

th

d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIRSubject to technical alterations.Status: 1995





Flanges in accordance with BS 3381, ANSI B 16.5,measures in inch



P. s. [lbs] 300 bis 1500 300 400 600 900



Innerring

Sealingelement

Cente-ringring

Sealingelement


Cente-ringring

d1

[inch]

d2 d3 d4 d2 d3 d4 d2 d3 d4No

min

al w

idth


Flanges in accordance with BS 3381, ANSI B 16.5,measures in mm


d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

150 300 600

[mm] [inch] o/I o/A

Sealingelement

Pressure stage [lbs]d2 d3

o/A

Cente-ringring

d4No

min

al w

idth

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

900

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

1500

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

2500No

min

al w

idth

o/I o/A o/Ao/I

Inner-ring

Sealingelement

Centeringring

Nominal pressure 10 k

Nom

inal

wid

th

o/I o/A o/Ao/I

d2 d3 d4d1 d2 d3 d4d1

Inner-ring

Sealingelement

Centeringring

Nominal pressure 16 k to 20 k

Nom

inal

wid

th






In accordance with the french standard NF–M–87621,measures in mm


Fitting to JIS flanges. Nominal pressure 10 k and 16 to 20 k, measures in mm


d2d3d4

d4

d1d2d3

CR CRIR

d2d3d4

d4

d1d2d3

CR CRIR

150 300 600

[mm] [inch] o/I o/A

Sealingelement

Pressure stage [lbs]d2 d3

o/A

Cente-ringring

d4

Nom

inal

wid

th

4.75

7 M

axifl

ex 9

5Pa

nton

e Blau

541

Pa

nton

e Rot

206

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

900

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

1500

o/I o/A

Sealingelement

d2 d3

o/A

Cente-ringring

d4

2500

Nom

inal

wid

th

o/I o/A o/Ao/I

Inner-ring

Sealingelement

Centeringring

Nominal pressure 10 k

Nom

inal

wid

th

o/I o/A o/Ao/I

d2 d3 d4d1 d2 d3 d4d1

Inner-ring

Sealingelement

Centeringring

Nominal pressure 16 k to 20 k

Nom

inal

wid

th






In accordance with the french standard NF–M–87621,measures in mm


Fitting to JIS flanges. Nominal pressure 10 k and 16 to 20 k, measures in mm


mounting instructionsKLINGER Spiral-Wound Gaskets Type CRIR Type CRIR/ PTFE inner ring Type CRIR/...

Documents

Transcript of mounting instructionsKLINGER Spiral-Wound Gaskets Type CRIR Type CRIR/ PTFE inner ring Type CRIR/...