Motor Fuel in Hong Kong (Final Report)

68
Final Report Feasibility Study of Using Biodiesel as Motor Fuel in Hong Kong Tender Ref: MV 00-153 Submitted to: Environmental Protection Department The Government of the Hong Kong Special Administrative Region by Dr. D.Y.C. Leung CEng, FIMechE, FInstE, FHKIOA, MHKIE Associate Professor Department of Mechanical Engineering The University of Hong Kong December 2003

Transcript of Motor Fuel in Hong Kong (Final Report)

Page 1: Motor Fuel in Hong Kong (Final Report)

Final Report

Feasibility Study of Using Biodiesel

as Motor Fuel in Hong Kong

Tender Ref: MV 00-153

Submitted to:

Environmental Protection Department

The Government of the Hong Kong Special Administrative Region

by

Dr. D.Y.C. Leung

CEng, FIMechE, FInstE, FHKIOA, MHKIE

Associate Professor

Department of Mechanical Engineering

The University of Hong Kong

December 2003

Page 2: Motor Fuel in Hong Kong (Final Report)

Executive Summary

There is a fast growing trend in the use of biodiesel over the past decade, mainly due to its

potential of reducing greenhouse gas and air pollutant emissions. Its capability in promoting

national agricultural industry and energy security are also the driving forces of its widespread

usage. Biodiesel is currently used in more than 20 countries in the world with an annual

consumption of about 2 million tonnes. Due to the increased public interest in biodiesel

application in Hong Kong, the Environmental Protection Department (EPD) of the HKSAR

Government commissioned the Department of Mechanical Engineering at the University of

Hong Kong in November 2000 to conduct a feasibility study on the use of biodiesel as an

automotive fuel in Hong Kong. The main objective of the study was to investigate the effect of

using different percentages of biodiesel fuel on air pollutant emissions, smoke opacity and

engine power in diesel vehicles in Hong Kong. The results would serve as a reference for

assessing the impact of using biodiesel under Hong Kong diesel vehicle operation environment.

The study consisted of two stages. The first stage included a preliminary test run (to verify the

testing protocol and to demonstrate the repeatability of the measurement methods), a main

dynamometer test for three diesel vehicles and an on-road emission study (to investigate the

vehicle emissions characteristics, in particular the NOx, while travelling inside a tunnel). The

second stage of the study involved a main dynamometer test for another seven diesel vehicles

and an on-road performance test. Three brands of biodiesel fuels were utilized for the main

dynamometer test, one of the fuels was produced from neat rapeseed oil while the other two

were derived from waste frying materials. The first stage study was completed in April 2001

and an interim report was submitted to the EPD in May 2001. The initial contractual

requirement only involved the main dynamometer test, but during the course of study, it was

decided to conduct an on-road performance test for 2 months in order to obtain the on-road

performance data on prolong usage of biodiesel fuel. Therefore, two additional vehicles were

employed for the on-road performance test, each for one brand of biodiesel fuel.

A monitoring committee, consisting of representatives from various government departments

including the Environmental Protection Department, Electrical and Mechanical Services

Department, Fire Services Department and Transport Department, trades, oil companies,

biodiesel suppliers as well as academia, was established to monitor the progress of the study.

The committee members have reviewed this report and endorsed all the findings.

2

Page 3: Motor Fuel in Hong Kong (Final Report)

Ten vehicles were successfully tested on the chassis dynamometer with the three available

biodiesel fuels. Each biodiesel fuel brand was tested according to three representative

biodiesel/ULSD blending ratios, i.e. 0% (ULSD), 20% (B20) and 100% (B100). Lower

percentage of biodiesel such as B5 was not included in this trial as the measurement accuracy

and variation would not be large enough for any significant analysis. Results of the ten tested

vehicles indicated that for an individual vehicle there was no unique answer to whether there

was any definite increment or decrement in the engine power, smoke opacity or air pollutants

emissions for using biodiesel, particularly for the case of B20. The actual performance of

vehicles using biodiesel depends on a number of factors such as engine design, service and

running conditions, engine age, etc. Due to the variations in the vehicles tested, the vehicular

performance and emission characteristics might be different for different vehicles. A break

down of the percentage change under different power and concentration ranges is shown in the

table below together with the overall average percentage change with respect to ULSD.

B20Engine Power (kW)

<30-3%

31–600%

61–90-1%

>90-2%

Overall-1%

Smoke Opacity (HSU) <15

-22%16–30-15%

31–45-16%

>45-11%

Overall-16%

CO Emission (ppm) <100-4%

101–200-11%

201–300-19%

>300-15%

Overal-14%

l

HC Emission (ppm) <10

-75%11–20-4%

21–30-12%

>30-14%

Overall -14%

NOx Emission (ppm) <300+5%

301–600-4%

601–900-1%

>9000%

Overall0%

B100Engine Power (kW)

<30-5%

31–600%

61–90-4%

>90-4%

Overall-3%

Smoke Opacity (HSU) <15

-60%16–30-59%

31–45-63%

>45-50%

Overall-58%

CO Emission (ppm) <1000%

101–200-9%

201–300-28%

>300-54%

Overall -23%

HC Emission (ppm)

<10-57%

11–20-36%

21–30-22%

>30-45%

Overall-40%

NOx Emission (ppm) <300

+13% 301–600

+8% 601–900

+5% >900

+11% Overall

+9%

From the overall average percentage variations of the ten vehicles shown above, it was found

that for B20, there was a slight decrease (-1%) in the engine power; 16% reduction in smoke

opacity, 14% reduction in CO and 14% reduction in HC. There was very little change in NOx

concentration. For B100, there was a slight decrease (-3%) in engine power; 58% reduction in

smoke opacity; 23% reduction in CO and 40% reduction in HC. However, there was a 9%

increase in NOx concentration.

The maximum loading applied in the chassis dynamometer test was 50% of the rated engine

power, which might not be able to reflect the emission behaviours at high road power conditions.

Therefore, an on-road emission study was conducted at two sites to determine the exhaust

emissions from a fully loaded van. The first site was at the Tsing Ma Bridge Tunnel that 3

Page 4: Motor Fuel in Hong Kong (Final Report)

provided a smooth and long flat road of about 2 km for testing. In addition to engine power

determination, this site allowed the measurement of vehicle emission inside a tunnel condition.

The other site was at the Cotton Tree Drive in Central District that provides a steep slope for the

test vehicle travelling up the hill. The emission test results obtained in the Tsing Ma Bridge

Tunnel indicated that the test vehicle’s engine power utilized was below 20% of the rated engine

power. On the other hand, when the same vehicle was driven up the Cotton Tree Drive, the

engine power utilized could reach 60% of the rated engine power. The result of the on-road

emission measurement indicated that when neat biodiesel fuel was used, there was a reduction of

40-46% ( -2 to -9 HSU) in smoke opacity while the NOx concentration was increased by 4 to

12% (with a maximum increase of 40ppm) in both the tunnel and the outdoor running

conditions.

Further to the dynamometer and on-road emission testing, an on-road performance test was done

to investigate the long-term effects of biodiesel fuels on the vehicle performance. Two goods

vehicles had been tested and the results revealed a small reduction in maximum engine power

and a decrease in smoke opacity after prolong usage of 100% biodiesel for two to three months.

The averaged reduction in maximum engine power and smoke opacity under the Diesel Lug

Down Test were 3% (-1kW out of 50kW) and 66% (-12HSU to -17HSU out of 26HSU)

respectively, which are comparable to the main dynamometer test result.

In addition, subjective evaluation on the use of biodiesel was also conducted by distributing

questionnaires to survey drivers’ opinions. Results indicated that about 71% of the responses

felt a reduction in road power. Over 85% of the responses commented that there were

reductions in smoke emissions and engine noise. As for the fuel consumption, about 24% of

the responses felt a slight decrease while 38% opined a slight increase and 14% opined

significant increase in fuel consumption.

Issues of concern

Notwithstanding the environmental benefits of using biodiesel, there is considerable concern

about roadworthiness and compatibility issues on the use of biodiesel. The following concerns

were identified after summarizing all the available information from previous meetings and

testing, which need to be addressed before making final decision regarding the use of biodiesel

in Hong Kong:

Fuel line compatibility to biodiesel and roadworthiness for in-service vehicles

Vehicle warranty and insurance when using biodiesel

4

Page 5: Motor Fuel in Hong Kong (Final Report)

Table of Content

Page

Executive summary 2

Background 8

1. Introduction 8

2. Objective 10

3. Test fuels 10

4. Test vehicles 11

5. Details of testing 12

5.1 Testing methods and procedures 12

5.2 Testing items 13

6. Instrumentation 14

7. Preliminary tests 14

7.1. Start-up run 15

7.2. Fuel change 15

7.3. Intra-day variation 16

7.4. Inter-day variation 16

8. Main dynamometer test results 16

8.1. Engine power 17

8.2. Smoke level 17

8.3. Carbon Monoxide (CO) 19

8.4. Hydrocarbons (HC) 19

8.5. Nitrogen Oxides (NOx) 20

9. On-road emissions study 20

9.1. Tsing Ma Bridge Tunnel 21

9.2. Cotton Tree Drive 21

10. On-road performance test results 22

11. Data analysis and discussion 23

12. Area of concerns and outstanding issues regarding the use of biodiesel 25

13. Conclusions 27

Acknowledgements 29

References 29

Photographs

Tables

Figures

5

Page 6: Motor Fuel in Hong Kong (Final Report)

Appendices

Appendix 1 Name list of the monitoring committee member

Appendix 2 Minutes of the 1st monitoring committee meeting

Minutes of the 1st monitoring committee meeting – tech. sub-com meeting

Minutes of the franchised bus technical sub-committee meeting

Minutes of the 2nd monitoring committee meeting

Minutes of the on-road performance test meeting

Minutes of the 3rd monitoring committee meeting

Minutes of the 4th monitoring committee meeting

Minutes of the 5th monitoring committee meeting

Minutes of the 6th monitoring committee meeting

Appendix 3 Work summary

Appendix 4a Draft Hong Kong biodiesel specifications

Appendix 4b Latest draft Hong Kong biodiesel specifications

Appendix 4c European biodiesel standard

Appendix 5 Testing reports of biodiesel fuels joining the test

Appendix 6 Sample calibration record

Appendix 7 Detailed testing procedures

Appendix 8 Raw data sheet of questionnaire survey for on-road performance test

Appendix 9 Summary of t-test results on the main dynamometer test

Appendix 10 Survey conducted by the MTA

Photo List

Photo 1. Chassis dynamometer vehicle exhaust emission test (Main dynamometer test)

Photo 2. Change fuel at Pokfulam Fire Station (Main dynamometer test)

Photo 3. SPX Dieseltune DX230 Smokemeter

Photo 4. AVL 490 Tachometer

Photo 5. Richard Oliver Tocsin 310 Combustion analyzer

Photo 6. Beckman Industrial Model 400A Hydrocarbons analyzer

Photo 7. On-road emissions study at lower deck of the Tsing Ma Bridge (On-road

emissions test)

Photo 8. On-road emissions study at Cotton Tree Drive (On-road emissions test)

Photo 9. Refuelling at Pokfulam Fire Station (On-road performance test)

Photo 10. A test vehicle on the chassis dynamometer under the diesel lug down test

(On-road performance test)

6

Page 7: Motor Fuel in Hong Kong (Final Report)

Table List

Table 7.1. Start-up run result

Table 8.1. Main dynamometer test result – M1

Table 8.2. Main dynamometer test result – M2

Table 8.3. Main dynamometer test result – M3

Table 8.4. Main dynamometer test result – M4

Table 8.5. Main dynamometer test result – M5

Table 8.6. Main dynamometer test result – M6

Table 8.7. Main dynamometer test result – M7

Table 8.8. Main dynamometer test result – M8

Table 8.9. Main dynamometer test result – M9

Table 8.10. Main dynamometer test result – M10

Table 8.11. Change in engine power, smoke level and gaseous pollutant

concentration – Biodiesel blends Vs ULSD

Table 9.1. On-road emission study result

Table 9.2. On-road emission study – evaluation of emissions at different roads

Table 10.1 On-road performance test result

Table 10.2 Summary of the questionnaire survey results

Table 11.1. Average percentage change for all vehicles tested

Figure List

Figure 5.1. Vehicle exhaust temperature and pollutant concentration of steady state

test

Figure 8.1. Maximum road power and its percentage variation of all vehicles

Figure 8.2(i) FAS smoke opacity and its percentage variation of all vehicles

Figure 8.2(ii) Diesel lug down smoke opacity and its percentage variation of all vehicles

Figure 8.3. CO concentration and its average percentage variation of all vehicles

Figure 8.4. HC concentration and its average percentage variation of all vehicles

Figure 8.5. NOx concentration and its average percentage variation of all vehicles

Figure 9.1. Average and maximum smoke level and air pollutant concentration for

On-road emission test at Cotton Tree Drive – Neat biodiesel Vs ULSD

Figure 9.2. Percentage variation of smoke level and air pollutant concentration for

On-road emission test at Cotton Tree Drive – Neat biodiesel Vs ULSD

Figure 11.1. Percentage variation of maximum road power and air pollutant

concentration (significant) for all vehicles

7

Page 8: Motor Fuel in Hong Kong (Final Report)

Background

To study the effect of biodiesel on vehicle’s power, smoke opacity and air emissions, the

Environmental Protection Department (EPD) of the HKSAR Government commissioned Dr.

D.Y.C. Leung of the Department of Mechanical Engineering at the University of Hong Kong to

conduct a series of test on the use of different biodiesel fuels with three biodiesel/ultra low

sulphur diesel (ULSD) blending ratios. The test comprised with two stages. The first stage

study included a preliminary run, on-road emission studies (Tsing Ma Bridge Tunnel) and main

dynamometer test for three diesel vehicles. The second stage study included the main

dynamometer test for seven diesel vehicles, on-road emission studies (Cotton Tree Drive) and an

on-road performance test. An interim report (Leung 2001) was submitted to the EPD in May

2001, which reported the result of the stage 1 study. This is the final report summarizing all

the results of the stage 1 and stage 2 tests and presenting an overview of the emission test result

when comparing the use of biodiesel fuels with ultra low sulphur diesel (ULSD), the normal

diesel fuel currently available at refuelling stations.

1. Introduction

Biodiesel is a mono-alkyl ester generally produced from a chemical process “Transestification”.

The feedstock of the production may come from most vegetable oils, natural fats or even used

frying oils. Biodiesel is a renewable diesel substitute that is one of the fastest growing

alternative fuels in the US and Europe.

Biodiesel is produced from renewable feedstock such as vegetable oils, natural fats and waste

lipids. The advancement of technologies in 80’s increased agricultural harvest that resulted in

surplus of crop products. Therefore, biodiesel is widely produced from agricultural products

such as soybean and rapeseed. Thus, biodiesel production is strongly supported by the

agricultural industries. However, the high production cost of biodiesel is a main barrier to its

widespread use. Even without any tax imposed on biodiesel, the cost of biodiesel derived from

vegetable oils is still higher than petroleum diesel. Another feedstock of biodiesel is the waste

lipids that could be collected from food factories and restaurants. This kind of biodiesel

feedstock can not only reduce the cost for landfill dumping and wastewater treatment but also

reduce the production cost of biodiesel.

Global warming issue and increasing greenhouse gas emissions raise public’s concern about the

8

Page 9: Motor Fuel in Hong Kong (Final Report)

importance of reducing exhaust emissions from motor vehicles. In order to lessen the impact of

greenhouse gas emissions, many countries encourage the use of renewable fuels. A lot of

research projects have been done to develop cleaner fuels, but not all of them can be applied in

commercial scale and some of the technologies are still in development stage. Biodiesel, a CO2

neutral renewable fuel (IEA 1998), is one of those alternative fuels that have been successfully

entered into the auto fuel markets.

In the past decade, the worldwide biodiesel application was in a fast growing trend because of

increasing public awareness on environmental protection. A number of pilot tests on biodiesel

were conducted in Europe and the USA demonstrating the capability of biodiesel in reducing

considerable amount of gaseous pollutants and greenhouse gases. Energy security that biodiesel

can bring to a country is another reason of the fast development of the fuel. The government of

Austria, France, Germany and Czech Republic are actively promoting the use of biodiesel and

its annual consumption increased in a fast pace. Biodiesel is currently used in more than 20

countries in Europe, North America and Asia with an annual consumption of about 1.8 million

tonnes, which is predicted to reach 2.8 million tonnes by the end of 2003 (Korbitz 2002).

Germany is the largest biodiesel producing countries and there are more than 1400 public pump

stations in Germany. Recently, the European Commission proposed a directive that petroleum

fuels would be progressively replaced by biofuels from 2% in 2005 to 5.75% in 2010. Except

Austria and Germany of which B100 are used, most of the EU countries using biodiesel

(including France, the U.K., Switzerland, Norway, Iceland etc.) adopt B5 in their diesel fuel,

while B20 has been used in the USA.

According to the worldwide experience and research results, the use of biodiesel in diesel

engines can reduce the emissions of unburned hydrocarbons, carbon monoxide, smoke and

particulate matter as compared to petro-diesel. Biodiesel contains virtually no sulphur and

hence the emission of sulphur dioxide will be eliminated. However, the results on nitrogen

oxides are contradictory as there are reports that indicate an increase (Geyer et al. 1984, Chang

et al. 1996) or a decrease in the emissions of nitrogen oxides as compared to petro-diesel,

according to different engines and testing cycles (Wang et al. 2000), and biodiesel with different

cetane numbers (Graboski et al. 2000).

To further study the feasibility of using biodiesel as a motor fuel in Hong Kong, the EPD has

commissioned Dr. D.Y.C. Leung of the Dept. of Mechanical Engineering at the University of

Hong Kong to launch a trial program for testing 10 diesel vehicles in different categories using

9

Page 10: Motor Fuel in Hong Kong (Final Report)

different biodiesel fuels and blending ratios. This trial program was later extended due to the

extension of the testing items (as described below) during the period of study.

A monitoring committee was set up to monitor the progress of the study. The committee

consists of representatives from various government departments (such as the EPD, Transport

Department (TD), Electrical & Mechanical Services Department (EMSD), and Fire Services

Department (FSD) etc.), relevant trades (such as the Taxi Associations’ Federation, Kowloon

Truck Merchants Association, and The Hong Kong Union of Light Van Employees etc.), oil

companies, biodiesel suppliers as well as academia. A whole list of the monitoring committee

members is given in Appendix 1. The chairman of the committee is Mr. W.C. Mok, the

Principal Environmental Protection Officer of the Motor Vehicle Emissions Group of the EPD.

The committee was formed in November 2000. Since then, five monitoring committee

meetings have been conducted. A franchised bus subcommittee meeting and an On-road

performance test subcommittee meeting have also been held to discuss more technical issues of

the test. In addition, in May 2001, the Motor Services Association (MTA) has commented on the

possible risk of using biodiesel in the vehicles in Hong Kong and subsequent meetings have

been held to tackle the issue. The notes of the committee and subcommittee meeting are attached

in Appendix 2 for reference. A summary of all the works performed during the whole study

period was shown in Appendix 3.

2. Objective

The main objective of the study was to investigate the effect of using biodiesel with different

blending percentages with ULSD on emissions, smoke opacity and engine power of in-service

diesel vehicles in Hong Kong. The results would serve as a reference for assessing the impact

of using biodiesel under Hong Kong diesel vehicle operation environment.

It should be mentioned that although different brands of biodiesel fuels were used in the study,

they were not identified in this study in order to avoid the comparison of the performance of

individual fuel brand.

3. Test fuels

Four biodiesel suppliers, i.e. Sunland Company, Dunwell Engineering Co. Ltd., HednesFord

Limited and Bio-clear Energies Limited, all expressed their willingness to join and provide their

biodiesel for the tests before the trial commenced. In order to ensure the quality of the

10

Page 11: Motor Fuel in Hong Kong (Final Report)

biodiesel fuel under test, one pre-requisite of participating in the test was that the biodiesel fuel

should comply with the draft biodiesel specifications stipulated by EPD (Appendix 4). The

biodiesel from the first three suppliers were accepted for testing after they had provided testing

reports (Appendix 5) and showed their compliance with the proposed biodiesel specifications.

While the last one, i.e. Bio-clear Energies Limited, could not provide the testing report and the

fuel was not tested at all. Also, HednesFord delayed its delivery schedule and its biodiesel was

only available for testing in August 2001. Therefore, this fuel was not tested in the early part

of the study. Overall, five vehicles were tested with all three qualified biodiesel fuels while the

other five vehicles were tested with two biodiesel fuels. The biodiesel fuels supplied by

Sunland, Dunwell and HednesFord were produced from neat rapeseed oil, waste frying oil and

waste frying fat respectively.

For the baseline testing and for fuel blending, Ultra Low Sulphur Diesel (ULSD) with sulphur <

0.005% was used because it was the only available diesel fuel in fuel refuelling stations in Hong

Kong. Therefore, this current study involved the emission performance comparison between

biodiesel with the diesel fuel available at pump in Hong Kong. Furthermore it has been agreed in

the 1st Monitoring Committee Meeting that symbol, instead of the names of the biodiesel

supplier, would appear in all the testing results in order to avoid direct comparison among

different biodiesel brands, as it was not the objective of this study.

Each biodiesel fuel brand was tested according to three representative biodiesel/ULSD blending

ratios, i.e. 0% (ULSD), 20% (B20) and 100% (B100). Lower percentage of biodiesel such as

B5 was not included in this trial as the measurement accuracy and variation would not be large

enough for any significant analysis.

4. Test vehicles

Ten test vehicles (M1 to M10) ranging from taxis, light buses and goods vehicles of different

registration years, brands and engine capacities were selected for the main dynamometer tests.

Two additional vehicles (R1 and R2) were employed for the on-road performance test. The

details of the test vehicles were as follows:

Vehicle No.

Vehicle Registration No.

Vehicle Make & Model Type of Vehicle Registration

Year Biodiesel Tested

Start-up Run P1

HT 11XX Ford Econovan Van 1998

P2 HE 24XX Isuzu FTR MGV 1997P3 HC 49XX Nissan E24 Van 1997

11

Page 12: Motor Fuel in Hong Kong (Final Report)

On-road Emissions Study O1 HT 11XX Ford Econovan Van 1998 A, B & C Main Dynamometer Test M1 CL 76XX Toyota Crown Taxi 1991 A & B M2* GE 83XX Isuzu NPR Light Goods Vehicle 1994 A & B M3 FZ 43XX Nissan Diesel Heavy Goods Vehicle 1993 A & B M4 JA 76XX Isuzu LT132 Single Deck Public Bus 1999 A & B M5 GD 78XX Nissan Civilian Public Light Bus 1994 A & B M6 HB 46XX Mazda E2200 Van 1993 A, B & C M7 HZ 74XX Mitsubishi Canter Light Goods Vehicle 1998 A, B & C M8 FD 99XX Isuzu FSR Medium Goods Vehicle 1991 A, B & C M9 ET 34XX Scania 93M Heavy Goods Vehicle 1990 A, B & C M10* GU 61XX Isuzu NPR Medium Goods Vehicle 1996 A, B & C On-road Performance Test R1 GC 92XX Isuzu NPR Light Goods Vehicle 1994 B R2 KD 38XX Mitsubishi Canter Medium Goods Vehicle 1997 A * Vehicle installed with a diesel oxidation catalyst (DOC).

5. Details of Testing

5.1. Testing methods and procedures

All vehicles participated in the test were required to meet the chassis dynamometer smoke test

requirement COP 1.04, i.e. the smoke levels at 3 speed points to be less than 50 HSU and

maximum wheel power to be more than 50% of the vehicle rated engine power under the use of

ULSD. Each vehicle was checked for the above requirement before accepted for the main

dynamometer test. The detailed testing schedule for the main dynamometer test was as

follows:

(i) Baseline testing: the test vehicle was first undergone testing using ULSD as baseline in the

vehicle testing centre. The testing included measurement of engine power, smoke, and air

pollutant concentrations. Details of the measurement items were given in Section 5.2

below.

(ii) B20 testing: Before switched to test B20 (that is, 20% biodiesel and 80% ULSD), the

baseline ULSD in the fuel tank of the test vehicle was drained out and refilled with

B20.The vehicle was then allowed to run on road for about 30 minutes’ for preconditioning

before, repeated testing according to item (i) again.

(iii) B100 testing: the procedures in item (ii) were repeated with the use of B100 (100%)

Biodiesel.

(iv) After finishing testing with one brand of biodiesel, the vehicle was returned to the owner

and reverted to the use of ULSD.

(v) After one week, the vehicle was sent back to the testing centre again and the above

procedures (i) to (iv) were repeated using other brands of biodiesel.

12

Page 13: Motor Fuel in Hong Kong (Final Report)

(vi) The procedures from item (i) to (v) were repeated for all biodiesel brands qualified for

testing.

(vii) After finishing testing with all biodiesel fuels, the vehicles were reverted back to ULSD

and returned to their owners.

(viii) Finally, the original base line readings were checked again by testing the vehicle that was

reverted to use ULSD after approximately one week of usage.

5.2. Testing items

Photo.1 shows a typical test vehicle ready to be tested on the chassis dynamometer in the testing

centre. As mentioned above, all vehicles were undergone the same set of testing and

measurement according to the following:

a. Free acceleration smoke test – smoke measurement under no load testing condition.

b. Diesel lug down test – maximum engine power and smoke measurement at 100%, 90%

and 80% maximum engine power.

c. Chassis dynamometer test –air pollutants (CO, HC, NOx), engine power and smoke

measurement at two steady state loading conditions: 20% and 50% of the vehicle’s rated

maximum power.

(Detailed descriptions of the testes are provided in Appendix 7)

Exhaust gas temperature and concentration of air pollutants at tailpipe were recorded during the

entire steady state test. Concentration of air pollutants was determined when the exhaust gas

reached its equilibrium temperature. A sample graph in Figure 5.1 illustrated the criteria for

deciding the steady state concentration of pollutants.

In order to minimize variation in vehicle performance and meteorological conditions, the test on

each biodiesel fuel would be completed within a normal working day. In addition, the relative

humidity (RH) at the testing site was also recorded during the test. NOx correction factor (kH)

for humidity (EEC Council Directive 1970) was applied to correct the influence of humidity on

the result of oxides of nitrogen. To ensure the accuracy of the measurements, each set of the

testing was repeated twice, so totally three set of readings were obtained for each measurement

item. In the results of the main dynamometer test only the average of the three readings were

presented in this report

The chassis dynamometer testing was performed in the Vehicle Testing Centre of Dah Chong

Hong (Motor Service Centre) Limited (DCH) at Apleichau. Photo 1 showed a typical test

13

Page 14: Motor Fuel in Hong Kong (Final Report)

vehicle ready to be run on the chassis dynamometer in the testing centre.

Fuel changing was performed at Pokfulam fire Station under the monitoring of the station’s

officers (Photo 2). Fuel sample was taken during each fuel change and stored for future oil

composition analysis.

6. Instrumentation

The following equipment was used for the whole main trial measurements:

Equipment Make Model Accuracy

Chassis dynamometer Clayton Industries ECCT500108 Air-cooled eddy current

PAU (500hp@50mhp) Smoke meter SPX Dieseltune DX230 ± 1% FS (Static) Combustion analyser for Carbon Monoxide & Nitrogen Oxides measurement

Richard Oliver Ltd. IGD Tocsin 310 ± 1% FSD

Hydrocarbons analyser (non-heated type)

Beckman Industrial Model 400A ± 1% FSD

The chassis dynamometer and smoke meter (Photos 3 & 4) are provided by Dah Chong Hong

Motor Services Centre, which are calibrated periodically by qualified technician/engineer. All

other emission analysers (Photos 4 & 5) are calibrated on site before conducting the first set of

measurement of the day using standard calibration gases. It was found that equipment drifting

was insignificant during the period of the measurement. A sample calibration record was

attached in Appendix 6 for reference. The testing was conducted and monitored by the deputy

Project Manager and two mechanics, all of them possessed more than five years experience on

chassis dynamometer and emission testing.

7. Preliminary tests

As it was not possible to run all of the tests on the same day at the same time, the tests had to be

spanned over a whole day and split into separate days for testing each of the biodiesel fuels.

This introduces uncertainty of intra-day and day-to-day variability of the engine performance.

Therefore, before the main dynamometer test, a series of preliminary tests were conducted to

develop the testing protocol and to estimate the degree of data variation of the measurement.

Particular concern was paid on the NOx measurement, as most published results indicated that

the change in NOx emission is only of the order of a few percents. Therefore, the repeatability of

14

Page 15: Motor Fuel in Hong Kong (Final Report)

NOx was of particular concern for this study. The preliminary tests included the following:

Trial Test vehicle Start-up run P1 Fuel change test P2 Intra-day variation ULSD: P1 & Biodiesel: P3 Day-to-day variation ULSD: P1 & Biodiesel: P3

The results of the above tests are tabulated in Table 7.1.

7.1 Start-up run

The objective of this test was to check whether the testing procedures mentioned in Section 5

could be conducted smoothly during actual running and to find out any difficulty during fuel

changing at the Pokfulam Fire Station. Since the fuel changing for B20 was more complicated

than B100, therefore only B20 was involved in this test run.

The results indicated that in general, the testing procedures in Section 5 could be implemented

smoothly except some improvement in the procedure of fuel changing. In addition to that, it

was found that the emission testing result at maximum power fluctuated throughout the

measurement, probably due to the tyre slippage. Subsequently, it was decided in the 2nd

Monitoring Committee meeting that only 20% and 50% of the rated engine power were selected

for testing during the main dynamometer test.

Furthermore, even there was a thoroughly cleaned fuel tank, it can also be observed that

changing back to ULSD immediately after the biodiesel test could not return to the original

vehicle operational condition, probably due to the cleansing effect of biodiesel and residue

biodiesel in the fuel line. As indicated from many studies, biodiesel is a good solvent and will

clean away the scale and built-up carbon, gum and varnish deposits in the fuel tank as well as in

the engine (Monyem & Gerpen 2001). Thus, the vehicle operational characteristics might be

changed after using biodiesel.

7.2 Fuel change

The objective of this test was to investigate any adverse effect due to fuel changing, particularly

on the NOx emission level. The test was conducted at full throttle condition for two speed

settings on two different days. The result indicated that fuel changing would not affect the

NOx measurement, as its variation is less than 2% (see Table 7.1). The maximum road power

variation was +1% and FAS smoke ranged between -1% and +3%.

15

Page 16: Motor Fuel in Hong Kong (Final Report)

7.3 Intra-day variation

The objective of this test was to check the variation of vehicular emissions within a day. Two

measurements were conducted, one at the beginning of the day and another was made several

hours after the first engine stoppage. ULSD and biodiesel were used consecutively for this test

with two different vehicles. The results indicated that in general there was little variation of air

pollutant emissions (e.g. maximum NOx variation was 1.9%) within a day even the engine had

been stopped for several hours (Table 7.1). However, some tests showed large data variations.

For example, it was observed that tyre slippage had occurred during the 50% rated power testing

of the Nissan E24 van which caused large variation in CO concentration measurement. As

shown in Table 7.1 the CO concentration was 262 ppm which became 383 ppm with tyre

slippage. Therefore, tyre slippage, normally occurred for prolong testing at high power, should

be avoided during testing.

7.4 Inter-day variation

The objective of the test is to confirm consistency of the result for the measurement conducted

over a period. Both ULSD and biodiesel were used in a 3-day test. The results in Table 7.1

showed that the repeatability of the data was generally good and the day-to-day variation was

small (e.g. maximum NOx variation was 2.2%).

From the results of the fuel change, intra-day and inter-day variation studying, the repeatability

and overall degree of data variation was satisfactory. However, large variation might occur for

very small concentration and under tyre slippage condition.

8. Main dynamometer test results

Totally ten vehicles were tested on the chassis dynamometer and the results were shown in

Tables 8.1. to 8.10 for the ten vehicles tested. Due to the fact that the baseline test on ULSD had

been conducted on each individual testing day, which, as mentioned in Section 7.1, might not be

repeatable after switching back from biodiesel to ULSD due to possible cleansing effect.

Therefore, analysis on the performance of each biodiesel fuel was conducted for those tests

performed on an individual day only, i.e. compared the result of B20 and B100 directly with that

of ULSD conducted at the beginning of the test.

The measured absolute changes in maximum engine power, smoke opacity level, CO, HC and

16

Page 17: Motor Fuel in Hong Kong (Final Report)

NOx concentration of the ten vehicles were shown in Table 8.11 for B20 and B100. The

variations of each of these parameters were discussed below.

8.1 Engine power

Power is one of the important parameters that indicate vehicle performance this parameter is of

particular importance in Hong Kong due to the fact that a large portion of our road network

consists of uphill and downhill driving conditions. In addition, most of the diesel vehicles are

load carrying, therefore if the fuel used will result in a significant drop in engine power it will

not likely be welcome by the vehicle operators.

The measured engine power for all the test vehicles using B20 and B100 were shown in Figure

8.1a. The results indicated that most of the test vehicles have shown a very small change in

maximum engine power, as shown in Table 8.11. The highest power drop was only 5 kW out of

a nominal power of 125 kW. The measured maximum engine power of the ten vehicles varied

from 27 kW to 186 kW.

Figure 8.1 b and c show the percentage changes in the maximum engine power for vehicles

using B20 and B100 respectively. The overall average for the ten vehicles was given in Figure

8.1d. For B20, the averaged percentage change in maximum road power varied from –6.7% to

+3.0% (-8kW to +4kW) with an average of –1.2% for the ten vehicles. Similar trend was

observed for vehicles when using B100, but the average maximum power drop was slightly

higher, varied from –6.9% to +5.3% (-7kW to +3kW) with an average of –2.6%. Overall, these

small drops in engine power would be unnoticeable by drivers when most of these vehicles were

operated under light to medium loading conditions.

8.2 Smoke level

Three types of smoke measurements were conducted for all the ten vehicles under dynamometer

test. They were free acceleration simulation (FAS) test, diesel lug down test and steady state

smoke measurement. Free acceleration test has been adopted by the Transport Department for

the quick checking of vehicular smoke on the road. Though convenience, the repeatability and

reliability of this measurement is usually not so high as compared with diesel lug down test,

which has been adopted by the EPD for checking smoke opacity of diesel vehicle. The diesel

lug down test has a better representation of the vehicle’s performance as it is run under a

load-simulated condition, which can avoid purposely tempering of vehicles. Steady state test,

unlike the FAS and diesel lug down test, does not involve any sharp change in fuel injection

17

Page 18: Motor Fuel in Hong Kong (Final Report)

inside the combustion cylinder, thus the test vehicle usually emits much less smoke than FAS

and lug down test. For example, in the present test, all the measured values under steady state

were below 10 HSU at 20% rated engine power. Based on the above fact, only the FAS and

diesel lug down test results were used for the comparison below.

Free acceleration smoke test (FAS)

The smoke opacity for individual vehicle under FAS condition was shown in Figure 8.2(i)a. for

ULSD as well as B20 and B100. The smoke levels obtained from the ULSD’s FAS tests varied

between 7 HSU and 49 HSU. For B20, vehicles reported a reduction in smoke level but the

magnitude of the reduction was small, varying from 0 HSU to 9 HSU (Table 8.11.). One

vehicle, i.e. M4 reported an increase in smoke level (+10 HSU). This was a coach fitted with

Euro II engine and the increase in smoke opacity occurred in two of the biodiesel fuels tested.

For B100, however, all the vehicles reported a reduction in smoke levels varying from 3 HSU to

23 HSU.

The above changes in smoke value were expressed in percentage variation in Figure 8.2(i) b and

c. For B20, the percentage change in smoke level varied from –34.8% to +31.9% (-15 HSU to

+12 HSU) with a mean variation of –11.4% (Figure 8.2(i)d.). Most of the tested vehicles

experienced a reduction in smoke opacity except M2 (slight increase) and M4 (increased by

31.9% or +12HSU). For B100, all vehicles experienced a dramatic reduction in smoke opacity

that varied from -1.3% to –73.4% (0 HSU to –27 HSU) with an average change of –43.5 %.

Smoke under diesel lug down test

The smoke opacity under lug down condition for individual vehicle were shown in Figure

8.2(ii)a. for ULSD as well as B20 and B100 with smoke levels obtained from all the lug down

tests varied from 3 HSU and 49 HSU. For both B20 and B100, all vehicles shown reduction in

smoke levels from 1 HSU to 9 HSU and from 8 HSU to 29 HSU respectively.

The above change in smoke reduction was expressed in terms of percentage in Figure 8.2(ii) b and

c. For B20, the percentage change in smoke level varied from –40.0% to +9.1% (-10 HSU to +2

HSU) with an average change of –15.6% (Figure 8.2(ii)d.). All the test vehicles experienced a

reduction in the average smoke opacity. For B100, all vehicles experienced a dramatic reduction in

smoke opacity that varied from -34.8% to -76.5% (-7 HSU to -30 HSU) with an average of

-58.4%.

18

Page 19: Motor Fuel in Hong Kong (Final Report)

8.3 Carbon Monoxide (CO)

The CO concentrations of individual vehicle at 20% and 50% rated engine power under steady

state condition were shown in Figure 8.3 a and b respectively. The CO concentrations for all the

fuels tested lied between 2 ppm and 292 ppm for 20% load, and 10 ppm to 905 ppm for 50%

load. As can be seen from Table 8.11, there was no systematic trend in CO concentration

variation for low load and high load conditions.

Figure 8.3 c and d showed the percentage variation in CO concentration of individual vehicle at

20% load for B20 and B100 respectively while Figure 8.3 e and f showed the corresponding

values at 50%. Figure 8.3 g and h showed the overall percentage variation in CO for 20% and

50% load respectively. As can be seen from all these figures, for B20 most of the vehicles

experienced a reduction in CO which varied from –60.0% to +65.4% (-216 ppm to +137 ppm)

with an average of -10.3%. For B100, the percentage change in CO varied from -75.6% to

+154.5% (-541 ppm to +89 ppm) with an average of -16.5%. It should be noted that large

variations in CO occurred in M2 and M10 in which both vehicles were installed with DOC. As

can be seen from Fig. 8.3 a and b, the measured absolute CO concentrations for these two

vehicles were very small and were much lower than those without DOC. In addition, testing

experience indicated that CO emission was very sensitive to the throttle position and it was

rather difficult to maintain CO constantly during the measurements. This induced larger error to

the results particularly those at small concentration.

8.4 Hydrocarbons (HC)

The HC concentration of individual vehicle at 20% and 50% rated engine power under steady

state condition were shown in Figure 8.4 a and b respectively. The HC concentrations lied

between 2 ppm and 37 ppm for 20% load and between 2 ppm and 71 ppm for 50% load for all

the fuels tested. As can be seen from Table 8.11. the changes in HC concentration were in

general, quite low, particularly for B20. However, due to the fact that the measured HC

concentrations for several vehicles (e.g. M2, M5 and M10) were also quite low, the percentage

change might be very high despite of the small changes in the concentration.

Figure 8.4 c and d showed the change of HC concentration in terms of percentage for individual

vehicle at 20% load for B20 and B100 respectively while Figure 8.4 e and f showed the

corresponding values at 50%. Figure 8.4 g and h showed the overall percentage variation in HC

for 20% and 50% load respectively. For B20, the percentage change in HC varied

from –75.3% to +108.5% (-11ppm to +6 ppm) with an average of –6.6%. For B100, the

19

Page 20: Motor Fuel in Hong Kong (Final Report)

percentage change in HC varied from –81.2% to +83.0% (-32ppm to +6ppm) with an average

of –28.2%. As mentioned above the large percentage variation was due to the small HC

concentration measured for particular vehicles, especially for those vehicles installed with DOC.

The result indicated that the reduction in HC is not obvious for B20 (six out of the ten tested

vehicles experienced reduction) but more prominent for B100 (nine out of the ten vehicles

showed reduction).

8.5 Nitrogen Oxides (NOx)

The NOx concentration of individual vehicle at 20% and 50% rated engine power under steady

state condition were shown in Figure 8.5 a and b respectively. The NOx concentrations lied

between 188 ppm and 1046 ppm for 20% load and between 278 ppm to 1920 ppm for 50% load

for all the fuels tested. The trend of the NOx concentration for various vehicles was quite similar

for 20% and 50% load condition and higher concentrations were obtained at higher load

condition due to higher combustion temperature. As shown in Table 8.11. the variation in NOx

concentration for individual vehicle was quite low as compared to the magnitude of the NOx

concentration measured.

Figure 8.5 c and d showed the percentage variation in NOx concentration of individual vehicle

at 20% load for B20 and B100 respectively while Figure 8.5 e and f showed the corresponding

values at 50%. Figure 8.5 g and h showed the overall percentage variation in NOx for 20% and

50% load respectively. For B20, the percentage change in NOx varied from –12.1% to +21.1%

(-97 ppm to +77 ppm) with an average change of +0.6%. Five of the vehicles showed an

increase in NOx concentration while the other five showed a decrease. For B100, the percentage

change in NOx varied from –19.6% to +39.4% (-116 ppm to +247 ppm) with an average change

of +7.8%. It can be observed that the average increase in NOx concentrations for all vehicles

tested under B100 were higher than those of B20. The result indicated that there was an

unnoticeable change in NOx for B20 but more prominent change was found for B100.

9. On-road emissions study

During the 2nd Monitoring Committee Meeting, there were some concerns that the 50%

maximum rated engine power might be not able to reflect the maximum loading achieved for the

vehicles running on road. It was therefore decided to investigate further whether the road

power of vehicles could be increased beyond 50% rated engine power for pollutant

measurement.

20

Page 21: Motor Fuel in Hong Kong (Final Report)

9.1 Tsing Ma Bridge Tunnel

With the permission from Tsing Ma Bridge Management Co. Ltd., a series of test was organized

in the Tsing Ma Bridge Tunnel during the period 9th to 24th April 2001. An on-road emissions

study was conducted on different road configurations. A light van (Ford Econovan 1998), fully

loaded with metal blocks and installed with an exhaust sampling probe at the tailpipe, was used

for the study. The van was driven at constant speed of 30 kph and 50 kph inside the Tunnel

(Photo 7). Real time smoke opacity and gaseous pollutants from the exhaust were collected and

determined. The tests were conducted on three separate days with different fuels: ULSD on the

1st day, neat biodiesel fuel on the 2nd day and ULSD again on the 3rd day.

The results of the tests are summarised in Table 9.1. It can be observed that a large reduction in

smoke level (approximate -46%) was obtained with the use of the neat biodiesel. However,

due to the small smoke values (less than 5 HSU) recorded during the measurement, larger error

may be involved. For NOx, an average of 12% increase in concentration was recorded.

It was not possible to determine the transient road power due to limitation of the equipment for

such determination. Oxides of nitrogen emission from a simulated chassis dynamometer test

had been used for estimating the road power during the sampling period. It could be noticed

that the NOx concentration of the on-road test was lower than that at 20% rated engine power

dynamometer tests. The results indicated that though the vehicle was fully loaded, running on

a straight road would only require less than 20% of the rated engine power to operate. It was

therefore considered that this straight road condition could not generate the desired high power

for our emission testing. However, the measurement can be considered as an indication of a

vehicle running inside a tunnel using biodiesel.

9.2 Cotton Tree Drive

In order to further determine the emission characteristic of ULSD and biodiesel fuels under high

engine power running conditions, several exploratory tests have been conducted at different

uphill locations and the results were summarized in Table 9.2. Finally location at the Cotton

Tree Drive in Central was selected as the most suitable site for the on-road emission testing.

The test started with the use of ULSD as baseline testing, followed by the testing of three

biodiesel fuels, namely Biodiesel A, B and C. The comparison of NOx concentration between

the on-road and dynamometer measurement showed that the road power output at the test site

was approximately 60% of the rated engine power. The test van was driven at 2nd gear and the

21

Page 22: Motor Fuel in Hong Kong (Final Report)

vehicle speed was maintained at 35 kph, which was approximate 3/4 of the full throttle position.

The measurement was started and stopped at two fixed locations of the road and repeated several

times (Photo 8). Total travel distance of each journey was 0.6 km and the measurement was

conducted for a period of 1 minute.

The results of the test are shown in Table 9.1. Figure 9.1 shows the average and maximum

smoke level and air pollutant concentration for ULSD and three other biodiesel fuels, and Figure

9.2 shows their percentage variations. The result indicated that there was a significant reduction

in smoke opacity, with maximum reduction from 51 to 61% and average reduction from 30 to

51% (range from –5 HSU to –25 HSU) for the three biodiesel fuels tested. The result was inline

with the averaged results of the diesel lug down test (-58% or -17 HSU), and the FAS test (-44%

or -13 HSU) present in Section 8.2. For CO emission, the use of biodiesel fuels resulted in a

maximum reduction from 52 to 59% (174 ppm to 197 ppm) and averaged reduction from 21 to

32% (38 ppm to 59 ppm). For NOx emission, an increase in concentrations was observed when

using biodiesel fuels with maximum increase from 6 to 13% (21 ppm to 50 ppm) and average

increase from 2 to 6% (6 ppm to 19 ppm). These results were inline with the chassis

dynamometer test result.

10. On-road performance test

Two vehicles, including a light goods vehicle and a medium goods vehicle, participated in this

on-road performance test. Each vehicle was tested with one biodiesel fuel at B100 during the

testing period. Refilling of biodiesel was carried out at Pokfulam Fire Station under the

monitoring of a station officer (Photo 9). Detailed information of the test is given in the table

below:

Vehicle no.

Vehicle type

Biodiesel tested

Testing Period (dd/mm/yyyy)

Mileage started (km)

Mileage ended (km)

Approximate fuel consumed (litres)

R1 LGV B 17/08/2001 to 05/11/2001

310327 318691 1735

R2 MGV A 24/09/2001 to 18/12/2001

96391 101108 1107

Detailed testing procedures were listed in Appendix 7. In brief, baseline ULSD lug down testing

was conducted at the beginning and the end of the trial to study the performance of the vehicles

before and after switching to biodiesel. To demonstrate the compatibility of biodiesel with the

22

Page 23: Motor Fuel in Hong Kong (Final Report)

fuel system and vehicle performance, lug down testing of the vehicles was conducted at a

monthly interval to provide the maximum road power and smoke opacity measurement for the

vehicles after using biodiesel (Photo 10).

Table 10.1 shows the results of the lug down tests conducted for the LGV (R1) and MGV (R2).

It can be observed that for R1, the measured maximum engine power remained fairly constant

throughout the measurement period. There was a dramatic drop in smoke opacity after shifting

to neat biodiesel (-56%) from 24 HSU dropped to 11 HSU. For R2, the maximum engine power

of the vehicle increased slightly (1% or 1 kW) after shifting to 100% biodiesel while the smoke

opacity dropped dramatically from 26 HSU to 5 HSU (-81%). It should be noted that for this

vehicle, there was a gradual reduction in the smoke opacity with increasing the time of biodiesel

usage and also the final ULSD emission test results were much lower than the initial values.

This phenomenon was also observed in the case of the LGV tested. This might indicate that

the use of both biodiesel fuels produce a cleansing effect on the engines of the two test vehicles,

resulting in cleaner exhaust gases.

In addition to the above quantitative measurement, questionnaires were also distributed regularly

to collect drivers’ opinions on road power, smoke opacity and fuel consumption etc. after using

biodiesel on their vehicles. The raw data sheet of the survey was shown in Appendix 8 and the

results are tabulated in Table 10.2. The results indicated that about 71% of the responses felt a

slight reduction in road power and over 86% of the responses commented that there were

reductions in smoke emissions and engine noise. The driver’s comments on fuel consumption

were quite diversified. About 24% of the responses opined slightly decrease in fuel consumption

while 38% opined slightly increase and 14% felt significant increase in fuel consumption. No

other adverse comments were reported.

Due to the comments of MTA on the possibility of fuel leakage caused by using biodiesel, all

the test vehicles were inspected visually when they returned to the testing centre for lug down

testing. However, no fuel leakage on the fuel system was observed during the testing period.

11. Data analysis and discussions

In Table 8.11 the average change in maximum engine power, smoke level, CO, HC and NOx

concentration for all the ten vehicles was shown. The results were calculated from all the 20%

load, 50% load and from all the ULSD and biodiesel fuels tested. The result indicated that

23

Page 24: Motor Fuel in Hong Kong (Final Report)

variations do exist between ULSD and biodiesel with 20% and 100% blending. However, due

to the presence of experimental errors, not all the variations are significant statistically. A t-test

at the 95% confidence interval has therefore been conducted on all the tests to see if the

variations in concentration were meaningful or not. The results were shown in Appendix 9.

Only those data with significance variations were extracted for analysis. This represented a

more realistic result taking into account of the statistical variation of data.

For those significant variations, the average percentage change in maximum engine power, FAS

smoke, Lug down smoke, CO, HC and NOx concentrations from vehicles were plotted in Figure

11.1 a to f. A break down of the percentage change under different power and concentration

ranges is shown in the table below together with the overall average percentage change with

respect to ULSD.

B20Road Power (kW)

<30 -3%

31–60 0%

61–90 -1%

>90 -2%

Overall -1%

Smoke Opacity (HSU) <15

-22% 16–30 -15%

31–45 -16%

>45 -11%

Overall -16%

CO Emission (ppm) <100 -4%

101–200 -11%

201–300 -19%

>300 -15%

Overall -14%

HC Emission (ppm) <10

-75% 11–20 -4%

21–30 -12%

>30 -14%

Overall -14%

NOx Emission (ppm) <300 +5%

301–600 -4%

601–900 -1%

>900 0%

Overall 0%

B100 Road Power (kW)

<30 -5%

31–60 0%

61–90 -4%

>90 -4%

Overall -3%

Smoke Opacity (HSU) <15

-60% 16–30 -59%

31–45 -63%

>45 -50%

Overall -58%

CO Emission (ppm) <100 0%

101–200 -9%

201–300 -28%

>300 -54%

Overall -23%

HC Emission (ppm) <10

-57% 11–20 -36%

21–30 -22%

>30 -45%

Overall -40%

NOx Emission (ppm) <300 +13%

301–600 +8%

601–900 +5%

>900 +11%

Overall +9%

From the table above, it was found that for B20, there was on average a slight decrease in the

power (-1%) and no noticeable change in NOx concentration (0%), a slight to moderate

reduction in HC (-14%), CO (-14%), and smoke opacity (-16%). For B100, the trends were

similar to B20 except for larger magnitude. There was an average of 9% increase in NOx

concentration and 3% drop in maximum engine power, 23% drop in CO, 40% drop in HC, and

58% drop in smoke opacity.

24

It is interesting to note that in the results of the on-road performance test, the smoke level and

road power immediately after changing to neat biodiesel were close to those measurements

conducted after the end of the testing period. This was a good evidence showing the

preconditioning after each fuel change was capable to allow the vehicle to achieve stable

conditions. At the end of the trial, a ULSD baseline measurement was also conducted and a

Page 25: Motor Fuel in Hong Kong (Final Report)

slight drop in smoke level was observed indicating the possible cleansing effect of the biodiesel.

The main dynamometer tests involved a large amount of practical work that could not be

completed on one day. It could be observed that the ULSD baseline testing conducted before

each biodiesel testing varied slightly for most of the test vehicles, and within acceptable range.

Also, the findings from the on-road performance test indicated that biodiesel might produce a

cleansing effect that affected the short-term vehicle performance. Therefore, the ULSD

baseline test employed at the beginning of each test day likely to be suitable to eliminate the

vehicle and system variations.

12. Area of concerns and outstanding issues regarding the use of biodiesel

During the course of the present study, the EPD had arranged two special meetings with the TD,

MTA and biodiesel suppliers to collect their comments on using biodiesel as motor fuel in Hong

Kong. In the meetings, some participants expressed their concerns about the potential hazards

that might be caused by using biodiesel and information on the latest technologies on motor

vehicles using biodiesel was exchanged.

Summarizing the comments of various parties from previous meetings, the following issues

were identified that need to be addressed before a decision can be made regarding the use of

biodiesel as a motor fuel in Hong Kong:

� Fuel line compatibility

During review meetings biodiesel suppliers indicated that biodiesel would attack natural

rubber in the fuel system but emphasised that the latest engine design uses synthetic rubber

instead of natural rubber. It is therefore generally believed that biodiesel should be

applicable to newer vehicle models but modifications may be required for aged vehicles

(e.g. vehicle older than 10 years).

In May 2002 the MTA has warned that vehicle using biodiesel might cause serious problem,

such as roadworthiness, but agreed that it would not cause immediate danger to road users.

They recommended that those vehicles using biodiesel should be inspected regularly. The

MTA was requested to provide more information to substantiate their claim, particularly on

the parts/components that can/cannot withstand the attack of biodiesel. However, the

MTA replied that they did not have such data.

25

Page 26: Motor Fuel in Hong Kong (Final Report)

In order to obtain more information about the attack rate of biodiesel on various elastomers,

HKU has initiated a study to investigate the compatibility of fuel hoses using biodiesel.

Four types of hoses, which could be obtained from the local market, were used for the test.

Two of them (i.e. Isuzu and Iveco) were original parts acquired from vehicle manufacturers

while the remaining two (i.e. Dayco and Gates) were purchased from local garages. Each

type of hose was tested with two biodiesel fuels and with three blending ratios, namely B0

(ULSD), B20 and B100. A tailor-made system was employed to simulate two operation

modes (immersion and circulation) and specimens were collected at the time interval of 200,

600, 1200, 1800 and 2400 hours. Size variation measurement, tension and bursting tests

were performed to assess the change in physical properties of the hoses at different time

intervals after testing with the biodiesel.

Size variation test demonstrated that there were systematic patterns of swelling of fuel

hoses (i.e. decrease in inner diameter and increased in outer diameter) for all biodiesel

blends. Tension test showed that load capacity decreased with increasing biodiesel

percentage and time period of usage. B20 gave similar size and physical properties changes

as ULSD. However, obvious swelling effect and greater reduction in tension strength

were observed for B100. In the B100 circulation test, oil droplets were found on the

surface of the hoses after about 300 hours and the surface became sticky afterward. It

could be noted that the outer layer of some hoses, especially for the Isuzu, were partly

dissolved under the B100 immersion environment and after about 1200 hours. Fuel hoses

supplied from Iveco, which is produced from biodiesel-resisted material, did not show any

swelling effect and no oil seepage was observed for the whole test even under B100

operations. The bursting test result also showed a reduced bursting strength of fuel hoses

(except Iveco) for all biodiesel blends.

The results suggested that cautious should be taken for vehicle using B100, particular for

older vehicle and it is highly recommended to change the fuel line to biodiesel compatible

material. Using 20% biodiesel (B20) or less seems to produce fewer problems but the real

impact needs further investigation. It is recognized that the result obtained so far cannot be

representative of the whole spectra as only a few types of fuel hoses have been tested while

there are more than 10 different types of fuel hose currently used in Hong Kong. Further

test is recommended to establish a more comprehensive picture on the influence of

biodiesel on fuel hoses with different materials.

26

Page 27: Motor Fuel in Hong Kong (Final Report)

� Warranty

The MTA has emphasised several times that they would not accept any blend of biodiesel

without principals’ authorization and those vehicles using biodiesel would have their

warranty voided. Although these mainly affect those newer vehicles, the issue of

warranty needs to be tackled as this will affect the confidence of biodiesel users. One

solution is that biodiesel suppliers can provide additional insurance to biodiesel users to

increase their confidence of using the fuel.

It is recognized that warranty policy of engine manufacturers did not match with

alternative/clean fuel policy of some overseas governments. For instant, biodiesel has

been used in the U.S.A. and Europe for several years with the support of local governments

for reducing greenhouse gases, promoting energy diversity and exploiting agricultural

produce etc. However, there are still a number of vehicle manufacturers not fully endorse

its usage, though this number is decreasing. It has also been recommended by some

members during the Monitoring Committee meeting that the government should impose

legislative measure so that all new imported diesel vehicles be biodiesel compatible. This

can be a proactive movement of the government for encouraging use of biofuels in Hong

Kong to demonstrate its commitment to protect the environment.

13. Conclusions

The feasibility study of using biodiesel as an automotive fuel in Hong Kong was completed. Ten

vehicles, of different types, brands, engine capacities and years of service, were tested on a

chassis dynamometer to measure the gaseous pollutant concentrations, smoke opacity and

maximum engine power. Two additional vehicles were selected to run on road with neat

biodiesel for testing their on-road performance. Before commencing all the testing, a testing

protocol was developed which was further validated through a series of preliminary tests.

For the main dynamometer test, there was no unique answer to whether there is any change in

the engine power, smoke opacity or air pollutants emissions for all the vehicles, particularly at

low biodiesel percentage. For example, almost all vehicles tested showed a dramatic reduction

in smoke opacity, but still there were one or two cases with smoke increase. Therefore, there

was no absolute performance data of biodiesel on different types of vehicles, it all depended on

the design of the engine, its service conditions and the percentage of biodiesel present in the fuel

mixture.

27

Page 28: Motor Fuel in Hong Kong (Final Report)

From the average performance of the ten vehicles, it was found that for B20, there was a slight

decrease (-1%) in the engine power; 16% reduction in smoke opacity, 14% reduction in CO and

14% reduction in HC. There was very little change in NOx concentration. For B100, there

was a slight decrease (-3%) in engine power; 58% reduction in smoke opacity; 23% reduction in

CO and 40% reduction in HC. However, there was a 9% increase in NOx concentration.

Testing was also conducted in the Tsing Ma Bridge Tunnel and Cotton Tree Drive in Central to

study the feasibility of obtaining higher engine power for pollutant measurement. It was found

that in the Tsing Ma Bridge Tunnel, the power with a fully loaded vehicle under constant speed

was about 20% of the maximum rated engine power while a maximum power of about 60% of

the rated engine power could be achieved for the fully loaded vehicle running up the Cotton Tree

Drive. Experimental results of the Tsing Ma Bridge Tunnel test showed that there was a

reduction in smoke emission (average -46% or -2 HSU) and an increase in NOx concentration

(average +12% or +34 ppm). The result at Cotton Tree Drive was similar to that of the Tsing

Ma Bridge Tunnel. Over 40% (-7 HSU) of smoke emission was reduced while a small change

in NOx was determined (average +4% or +12 ppm).

To obtain more data on the day-to-day operation of diesel vehicles using biodiesel fuels, an

on-road performance test was conducted on two vehicles, one LGV and one MGV, each using

one type of biodiesel throughout the period. The results of the monthly Lug Down test revealed

that there was an unnoticeable change in the maximum engine power but a significant

improvement in smoke opacity after shifting to use 100% biodiesel. The smoke opacity of the

Diesel Lug Down Test reduced 56% (13 HSU) and 81% (21 HSU) for the two vehicles R1 and

R2 respectively. In addition to the above quantitative measurement, questionnaires survey on

drivers’ opinions indicated that about 71% of the responses felt a reduction in engine power.

Over 86% of the responses commented that there were reductions in smoke emissions and

engine noise. As for the fuel consumption, about 24% of the responses felt a slightly decrease

while 38% opined a slight increase and 14% opined significant increase in fuel consumption.

Apart from that no adverse comments from drivers was received. Due to the comments from

MTA on the possibility of fuel leakage, all the test vehicles were inspected visually when they

returned to the testing centre for lug down testing. No fuel leakage from the fuel hose was

observed during the testing period.

The emission testing results indicated that using B100 could reduce a considerable amount of air

pollutants but a slight increase in NOx emission and a small drop in fuel economy would be

28

Page 29: Motor Fuel in Hong Kong (Final Report)

encountered. Its ability in reducing air pollutant emissions diminishes with decreasing

biodiesel percentage. Nevertheless, prominent effects could still be achieved even at B20.

However, some important issues, such as the fuel line compatibility, roadworthiness and

warranty, would be arisen due to the use of biodiesel. Unless these issues could be fully

resolved, its attractiveness to our transportation system would be limited.

Acknowledgements

The following companies/organisations are gratefully acknowledged for their help during the

whole biodiesel study:

- Dah Chong Hong (Motor Service Centre) Ltd.

- Dunwell Engineering Co. Ltd.

- Hongkong & China Gas Co. Ltd.

- Hongkong Electric Co. Ltd.

- Hong Kong Polytechnic University

- Sagawa Express (HK) Company Ltd.

- Skytruck Transportation Ltd.

- Sunland Company

- Tsing Ma Management Ltd.

- United Friendship Taxi Owners and Drivers Association Ltd.

- Uni-power Engineering Ltd.

References

1. Chang D.Y.Z., Van Gerpen J.H., Lee, I., Johnson, L.A., Hammond, E.G., Marley, S.J., “ Fuel

properties and emissions of soybean oil esters as diesel fuel”, J. Amer. Oil Chemist’s Soc. 73,

1549-55, 1996.

2. EEC Council Directive 70/220/EEC, 1970, Appendix 8: Calculation of the Emission of

Pollutants.

3. EPA420-P-02-001, 2002, A comprehensive analysis of biodiesel impacts on exhaust

emissions, Draft Technical Report.

4. Geyer, M.S., Jacobus, M.J., Lestz, S.S., “Comparison of diesel engine performance and

emissions from neat and tranesterified vegetable oils”, Tran. ASAE, 27, 375-81, 1984.

5. Graboski, M.S., McCormick, R.L., Alleman, T.L. & Herring, A.M., “Effect of biodiesel

composition on NOx and PM emissions from a DDC series 60 engine”, Final Report to

National Renewable Energy Laboratory, Colorado Institute for Fuels and Engine Research, 29

Page 30: Motor Fuel in Hong Kong (Final Report)

Colorado School of Mines, 2000.

6. “Greenhouse gas balances of bioenergy systems”, International Energy Agency IEA Task 25,

www.ieabioenergy.com/media/17_AR1998Task25colour.pdf, 1998.

7. Korbitz, W., “New trends in developing biodiesel world-wide”, Power Crops for the

Americas, USA, 2002.

8. Leung, D.Y.C., “Feasibility study of using biodiesel as motor fuel in Hong Kong” Interim

Report submitted to the Environmental Protection Department, HKSAR, May 2001

9. MSED Report #96-01 “Evaluation of heavy duty engine exhaust emissions using biodiesels

and an oxidation catalyst., report submitted to Environment Canada by Environmental

Technology Centre, 1996.

10. Monyem, A. & Van Gerpen, J.H., “The effect of biodiesel oxidation on engine performance

and emissions”, Biomass & Energy 20, 317-325, 2001.

Wang, W.G., Lyons, D.W., Clark, N.N. Gautam, M. & Norton P.M.,”Emissions from nine heavy

trucks fuelled by diesel and biodiesel blend without engine modification”, Env. Sci. Tech. 34,

933-939, 2000.

30

Page 31: Motor Fuel in Hong Kong (Final Report)

Photographs

31

Page 32: Motor Fuel in Hong Kong (Final Report)

Photo 1. Chassis dynamometer vehicle exhaust emission test (Main dynamometer test)

Photo 2. Change fuel at Pokfulam Fire Station (Main dynamometer test)

32

Page 33: Motor Fuel in Hong Kong (Final Report)

Photo 3. SPX Dieseltune DX230 Smokemeter

Photo 4. AVL 490 Tachometer

33

Page 34: Motor Fuel in Hong Kong (Final Report)

Photo 5. Richard Oliver Tocsin 310 Combustion analyser

Photo 6. Beckman Industrial Model 400A Hydrocarbons analyser

34

Page 35: Motor Fuel in Hong Kong (Final Report)

Photo 7. On-road emissions study at lower deck of the Tsing Ma Bridge (On-road emissions

test)

Photo 8. On-road emissions study at Cotton Tree Drive (On-road emissions test)

35

Page 36: Motor Fuel in Hong Kong (Final Report)

Photo 9. Refuelling at Pokfulam Fire Station (On-road performance test)

Photo 10. A test vehicle on the chassis dynamometer under the diesel lug down test (On-road

performance test)

36

Page 37: Motor Fuel in Hong Kong (Final Report)

Tables

37

Page 38: Motor Fuel in Hong Kong (Final Report)

Preliminary Run Fuel Change Intra-day Day-to-day Test Vehicle S1 S2 S1 S3 S1 S3 Test Date 06-1-01 19-1-01 09-2-01 01-2-01 am 01-2-01 pm 20-3-01 am 20-3-01 pm 30-1-01 31-1-01 01-2-01 19-3-01 19-3-01 20-3-01 21-3-01

ULSD ULSD ULSD ULSD Test Fuel ULSD B20 ULSD ULSD B100 ULSD ULSD B100

(Before) (After) (Before) (After)

Free Acceleration Smoke Test Smoke Level (HSU) 12 8 11 17 16 16 16 20 20 33 19 20 20

Per varicentage ation * - - 31% -6 % - -1% - 3% 0 0 - -3% +2% +2% Diesel Lug Down Test Maximum Power (kW) 34 31 33 101 102 104 105 33 30 29 32 33 32 Percentage variation * - -9% -3% - +1% - +1% +4.8% -4.8% - -1% +2% -1% Maximum Smoke Level

9 4 9 7 4 5 2 3 5 19 8 3 5 (HSU) Percentage variation * - -56% 0% - -43% - -60% -25.0% +25.0% - +50% - 44% -6%

Steady Speed Test Vehicle Speed (kph) Full Throttle @ Maximum Power Speed 50 Road Power (kW) 32 30 31 102 102 105 104 10 20 10 20 11 28 11 28 10 10 10 11 11 11 11 HC Concentration (ppm) 11 4 15 5 16 10 11 14 Percentage variation * -18% -13% +18% +13% - -14% -6% +20% CO Concentration (ppm) 166 137 141 73 68 66 60 132 108 131 107 166 383# 166 262 131 132 132 174 136 166 156 Percentage variation * - -17% -15% - -7% - -10% 0% +1% -0% -1% 0% +19% 0% -19% -1% +0% +0% - -11% +9% +2% NOx Concentr (ppation m) 475 431 436 544 539 581 573 293 494 297 496 409 786 408 766 299 302 293 381 401 409 410 Percentag variatie on * - -9% -8 % - -1% - -1% -1 % 0 % +1 % 0% 0 % +1% 0 % -1% 0 % +1% -2 % - -1% +1% +1%

HumiRelative dity (%) 62 62 62 49 52 63 63 64 64 68 68 71 71 74 71 64 68 64 70 71 71 74 Steady Speed Test Vehicle Speed Full Throttle @ 45kph Full Throttle @ 35kph Part Load @ 50kph Road Power (kW) 27 26 27 37 38 37 36 28 28 28 28 HC concentration (ppm) 5 5 4 4 Percentage variation * - +15% -8% -8% CO concentration (ppm) 102 102 95 52 44 48 48 359 155 383# 165 Percentage variation * - -1% -7% - -15% - -1% - -34% +63% - 30% NOx concentr (ppmation ) 464 455 451 816 814 883 864 793 794 786 816 Percentage variation * - -2% -3% - 0% - -2% - -1% -2% +2%

HuRelative midity (%) 62 62 62 49 52 63 63 70 71 71 74 * Percentage variation of Intra-day and day-to-day test was devised from mean value # Tyre slipping occurred

Table 7.1. Start-up run result

Page 39: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃

Feasibility study of using Biodiesel as Motor Fuel in Hong Kong 車輛廢氣測試結果

Test Result 車輛登記號碼 Vehicle Registration Mark: CL76XX 車廠及型號 Make & Model: Toyota Crown

車輛製造年份 Vehicle Manufacture Year: 1991 車輛種類 Vehicle Type: Taxi

測試日期 Test Date: 14-Mar-01 14-Mar-01 14-Mar-01 7-Mar-01 7-Mar-01 7-Mar-01 4-Apr-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 33 26 17 42 32 18 37

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 33 34 33 33 32 31 31

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 18 14 6 26 17 7 20

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 15 17 6 20 21 7 17

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 30 22 8 34 24 8 28

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 11.4 11.4 11.4 11.4 11.4 11.4 11.4

Road Power (kW)

固定車速度時所量度得的煙度 5 1 0 7 6 1 7

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 19 24 17 25 19 14 15

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 199 176 126 229 169 119 208

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 561 572 620 537 544 658 603

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 311 276 260 266 261 252 259

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 67 67 74 74 74 74

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 28.5 28.5 28.5 28.5 28.5 28.5 28.5

Road Power (kW)

固定車速度時所量度得的煙度 9 3 1 16 10 4 19

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 15 20 14 13 12 11 10

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 205 172 139 248 212 195 447

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 868 862 864 847 848 885 855

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 522 451 432 456 446 438 472

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 64 66 74 74 74 74

Relative Humidity (%)

Table 8.1. Main dynamometer test result – M1

Page 40: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃

Feasibility study of using Biodiesel as Motor Fuel in Hong Kong 車輛廢氣測試結果

Test Result 車輛登記號碼 Vehicle Registration Mark: GE 83XX 車廠及型號 Make & Model: ISUZU NPR

車輛製造年份 Vehicle Manufacture Year: 1994 車輛種類 Vehicle Type: LGV

測試日期 Test Date: 26-Feb-01 26-Feb-01 26-Feb-01 12-Mar-01 12-Mar-01 12-Mar-01 4-Apr-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 24 24 19 22 23 13 31

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 57 58 57 58 58 56 57

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 33 24 8 29 25 10 32

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 24 19 6 23 20 10 24

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 26 21 8 34 24 12 28

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 16.4 16.4 16.4 16.4 16.4 16.4 16.4

Road Power (kW)

固定車速度時所量度得的煙度 4 3 1 4 3 3 3

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 6 7 6 13 4 7 6

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 4 4 9 5 3 3 0

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 738 725 801 743 680 712 755

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 254 235 229 258 242 238 218

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 61 66 71 64 55 51 74

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 41 41 41 41 41 41 41

Road Power (kW)

固定車速度時所量度得的煙度 15 15 5 18 18 10 20

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 5 4 3 11 3 5 5

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 15 13 16 18 16 14 8

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 1470 1536 1605 1492 1416 1409 1516

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 378 380 376 409 393 386 361

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 61 71 70 64 52 51 74

Relative Humidity (%)

Table 8.2. Main dynamometer test result – M2

Page 41: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃

Feasibility study of using Biodiesel as Motor Fuel in Hong Kong 車輛廢氣測試結果

Test Result 車輛登記號碼 Vehicle Registration Mark: FZ43XX 車廠及型號 Make & Model: Nissan Diesel CKB520

車輛製造年份 Vehicle Manufacture Year: 1993 車輛種類 Vehicle Type: MGV

測試日期 Test Date: 27-Feb-01 27-Feb-01 27-Feb-01 6-Mar-01 6-Mar-01 6-Mar-01 4-Apr-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 42 27 15 34 32 20 47

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 178 182 176 186 181 181 180

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 43 38 16 47 38 18 49

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 46 34 15 44 35 19 44

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 46 34 16 44 38 20 49

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 45 45 45 45 45 45 45

Road Power (kW)

固定車速度時所量度得的煙度 0 0 0 4 1 2 1

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 24 26 30 18 23 18 11

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 165 187 254 208 150 159 191

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 1019 949 1036 993 973 967 1126

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 208 200 205 210 221 203 210

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 62 63 63 64 64 74

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 112.5 112.5 112.5 112.5 112.5 112.5 112.5

Road Power (kW)

固定車速度時所量度得的煙度 6 1 1 8 5 3 6

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 25 26 27 20 24 17 14

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 98 98 109 100 84 76 99

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 1605 1582 1639 1560 1561 1550 1639

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 351 341 351 358 352 334 337

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 63 62 64 64 62 74

Relative Humidity (%)

Table 8.3. Main dynamometer test result – M3

Page 42: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃 Feasibility study of using Biodiesel as Motor Fuel in Hong Kong

車輛廢氣測試結果 Test Result

車輛登記號碼 Vehicle Registration Mark: JA76XX 車廠及型號 Make & Model: Isuzu LT 132L

車輛製造年份 Vehicle Manufacture Year: 1999 車輛種類 Vehicle Type: Coach

測試日期 Test Date: 26-May-01 26-May-01 26-May-01 14-Jul-01 14-Jul-01 14-Jul-01 21-Jul-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 38 46 19 37 49 26 45

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 102 98 99 102 101 96 101

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 10 6 2 7 8 3 7

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 10 7 2 7 7 4 7

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 18 15 5 15 13 8 14

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 29.4 29.4 29.4 29.4 29.4 29.4 29.4

Road Power (kW)

固定車速度時所量度得的煙度 1 0 1 4 0 0 3

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 25 20 19 20 17 4 10

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 251 183 144 262 197 137 169

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 271 286 302 283 249 233 244

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 282 279 282 287 262 263 291

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 65 65 77 77 77 71

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 73.5 73.5 73.5 73.5 73.5 73.5 73.5

Road Power (kW)

固定車速度時所量度得的煙度 9 2 5 14 11 5 9

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 20 17 15 11 11 4 7

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 121 114 109 159 142 123 163

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 364 372 422 365 368 402 400

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 390 378 370 400 372 373 395

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 69 65 65 77 77 77 71

Relative Humidity (%)

Table 8.4. Main dynamometer test result – M4

Page 43: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃

Feasibility study of using Biodiesel as Motor Fuel in Hong Kong 車輛廢氣測試結果

Test Result 車輛登記號碼 Vehicle Registration Mark: GD78XX 車廠及型號 Make & Model: Nissan Civilian

車輛製造年份 Vehicle Manufacture Year: 1994 車輛種類 Vehicle Type: PLB

測試日期 Test Date: 20-Jul-01 20-Jul-01 20-Jul-01 5-Jul-01 5-Jul-01 5-Jul-01 2-Aug-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 15 12 15 18 13 12 18

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 57 57 60 57 57 59 57

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 19 17 11 24 17 12 25

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 18 15 11 23 14 9 24

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 19 18 10 26 18 13 22

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 17.6 17.6 17.6 17.6 17.6 17.6 17.6

Road Power (kW)

固定車速度時所量度得的煙度 4 3 1 3 0 0 3

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 7 2 2 4 2 4 4

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 81 79 82 57 58 59 76

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 204 222 238 206 215 245 206

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 194 198 183 192 219 193 193

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 73 69 71 58 63 63 71

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 44 44 44 44 44 44 44

Road Power (kW)

固定車速度時所量度得的煙度 49 22 14 47 30 17 45

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 3 7 3 2 2 4 3

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 647 466 241 754 539 241 716

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 295 298 308 279 281 304 293

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 415 395 368 423 408 399 427

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 73 71 69 58 63 63 71

Relative Humidity (%)

Table 8.5. Main dynamometer test result – M5

Page 44: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃 Feasibility study of using Biodiesel as Motor Fuel in Hong Kong

車輛廢氣測試結果 Test Result

車輛登記號碼 Vehicle Registration Mark: HB46XX 車廠及型號 Make & Model: Mazda E2200

車輛製造年份 Vehicle Manufacture Year: 1993 車輛種類 Vehicle Type: Van

測試日期 Test Date: 10-Oct-01 10-Oct-01 10-Oct-01 30-Oct-01 30-Oct-01 30-Oct-01 7-Nov-01 7-Nov-01 7-Nov-01 12-Nov-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD B20-Bio C B100-Bio C ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 26 24 17 28 27 18 34 32 18 35

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 29 29 28 29 28 27 30 28 29 30

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 46 44 30 49 47 29 42 43 26 40

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 43 42 26 45 46 26 40 40 25 38

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 38 38 24 41 39 22 37 38 22 39

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8

Road Power (kW)

固定車速度時所量度得的煙度 5 6 3 7 6 4 6 5 2 8

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 15 14 11 15 16 13 14 14 14 14

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 228 233 197 215 212 190 223 206 180 230

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 188 228 263 202 208 233 213 218 234 226

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 203 193 193 149 160 187 190 173 169 216

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 52 49 46 60 57 54 53 54 43 47

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 22 22 22 22 22 22 22 22 22 22

Road Power (kW)

固定車速度時所量度得的煙度 31 31 17 32 30 20 33 28 15 32

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 62 68 44 71 65 49 65 56 34 69

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 768 905 760 757 745 674 783 723 492 763

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 527 566 520 576 537 474 596 614 557 615

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 299 296 305 212 242 300 280 230 258 296

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 52 46 49 60 57 54 53 54 43 47

Relative Humidity (%)

Table 8.6. Main dynamometer test result – M6

Page 45: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃

Feasibility study of using Biodiesel as Motor Fuel in Hong Kong 車輛廢氣測試結果

Test Result 車輛登記號碼 Vehicle Registration Mark: HZ74XX 車廠及型號 Make & Model: Mitsubishi Canter

車輛製造年份 Vehicle Manufacture Year: 1998 車輛種類 Vehicle Type: LGV

測試日期 Test Date: 6-Oct-01 6-Oct-01 6-Oct-01 20-Oct-01 20-Oct-01 20-Oct-01 27-Oct-01 27-Oct-01 27-Oct-01 10-Nov-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD B20-Bio C B100-Bio C ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 19 16 8 20 18 9 18 15 8 18

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 73 72 69 70 70 68 71 69 68 70

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 12 9 5 12 10 5 12 8 3 11

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 10 8 4 10 8 3 9 7 3 9

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 10 7 3 8 7 1 8 6 2 8

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 22 22 22 22 22 22 22 22 22 22

Road Power (kW)

固定車速度時所量度得的煙度 2 1 0 1 1 0 1 1 0 1

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 28 26 21 26 22 19 18 15 10 18

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 157 142 135 132 109 86 137 123 115 131

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 354 364 378 375 375 396 362 380 380 369

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 233 223 221 218 215 194 189 184 195 197

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 62 55 58 49 52 54 66 72 67 42

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 55 55 55 55 55 55 55 55 55 55

Road Power (kW)

固定車速度時所量度得的煙度 5 4 2 5 4 0 5 4 1 6

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 36 33 21 33 30 16 32 27 19 24

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 115 123 102 106 102 93 110 115 106 106

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 527 531 585 547 556 593 547 556 573 546

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 361 355 361 357 345 308 287 313 301 310

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 62 58 55 49 52 54 66 72 67 42

Relative Humidity (%)

Table 8.7. Main dynamometer test result – M7

Page 46: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃 Feasibility study of using Biodiesel as Motor Fuel in Hong Kong

車輛廢氣測試結果 Test Result

車輛登記號碼 Vehicle Registration Mark: FD99X 車廠及型號 Make & Model: Isuzu

車輛製造年份 Vehicle Manufacture Year: 1991 車輛種類 Vehicle Type: MGV

測試日期 Test Date: 19-Sep-01 19-Sep-01 19-Sep-01 3-Oct-01 3-Oct-01 3-Oct-01 17-Oct-01 17-Oct-01 17-Oct-01 31-Oct-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD B20-Bio C B100-Bio C ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 44 43 35 49 47 41 47 44 39 45

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 77 76 74 78 77 73 75 75 73 76

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 37 35 13 33 32 15 28 25 13 30

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 35 36 12 33 29 15 26 25 12 28

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 38 36 13 35 31 16 28 25 12 27

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 22 22 22 22 22 22 22 22 22 22

Road Power (kW)

固定車速度時所量度得的煙度 7 6 3 9 8 5 7 7 1 5

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 37 35 17 37 31 16 30 28 18 30

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 286 272 233 292 264 169 258 228 205 274

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 482 477 549 495 467 504 456 455 529 467

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 322 326 319 328 324 316 327 318 313 322

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 64 61 63 60 62 62 51 51 52 61

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 55 55 55 55 55 55 55 55 55 55

Road Power (kW)

固定車速度時所量度得的煙度 22 15 5 21 14 8 9 9 5 11

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 52 47 25 51 40 25 49 42 28 48

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 724 634 254 734 622 193 557 373 216 584

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 948 947 1137 940 959 1102 985 982 1102 987

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 489 497 482 477 484 469 475 478 472 490

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 64 63 61 60 62 62 51 51 52 61

Relative Humidity (%)

Table 8.8. Main dynamometer test result – M8

Page 47: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃 Feasibility study of using Biodiesel as Motor Fuel in Hong Kong

車輛廢氣測試結果 Test Result

車輛登記號碼 Vehicle Registration Mark: ET34XX 車廠及型號 Make & Model: SCANIA

車輛製造年份 Vehicle Manufacture Year: 1990 車輛種類 Vehicle Type: HGV 測試日期 Test Date: 3-Dec-01 3-Dec-01 3-Dec-01 27-Nov-01 27-Nov-01 27-Nov-01 20-Nov-01 20-Nov-01 20-Nov-01 10-Dec-01

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD B20-Bio C B100-Bio C ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 38 33 14 38 30 19 35 24 9 38

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 125 122 119 127 125 125 123 115 116 123

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 16 17 8 20 7 6 21 16 9 17

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 19 19 8 20 11 6 23 19 9 21

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 23 23 9 25 15 7 26 21 9 28

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 37 37 37 37 37 37 37 37 37 37

Road Power (kW)

固定車速度時所量度得的煙度 2 1 0 1 1 0 3 1 0 1

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 13 12 9 12 14 8 13 12 9 11

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 102 104 125 109 81 79 97 96 112 112

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 854 854 889 801 834 932 730 748 836 746

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 249 249 262 253 235 230 220 241 251 236

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 70 67 67 50 47 50 31 30 36 62

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 92.5 92.5 92.5 92.5 92.5 92.5 92.5 92.5 92.5 92.5

Road Power (kW)

固定車速度時所量度得的煙度 5 3 1 3 2 0 5 2 1 4

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 17 18 11 18 19 16 19 18 14 19

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 221 196 201 188 166 160 189 176 172 234

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 1674 1751 1920 1724 1736 1810 1609 1626 1799 1712

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 378 359 345 369 359 345 282 351 361 397

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 62 65 62 50 47 50 31 30 36 65

Relative Humidity (%)

Table 8.9. Main dynamometer test result – M9

Page 48: Motor Fuel in Hong Kong (Final Report)

生化柴油試驗計劃 Feasibility study of using Biodiesel as Motor Fuel in Hong Kong

車輛廢氣測試結果 Test Result

車輛登記號碼 Vehicle Registration Mark: GU61XX 車廠及型號 Make & Model: Isuzu NPR

車輛製造年份 Vehicle Manufacture Year: 1996 車輛種類 Vehicle Type: MGV

測試日期 Test Date: 6-Dec-01 6-Dec-01 6-Dec-01 30-Nov-01 30-Nov-01 30-Nov-01 23-Nov-01 23-Nov-01 23-Nov-01 0-Jan-00

測試燃油 Fuel ULSD B20-Bio A B100-Bio A ULSD B20-Bio B B100-Bio B ULSD B20-Bio C B100-Bio C ULSD

空擋加速煙度測試 (踩三腳) Free Acceleration Smoke Test (HSU)

平均煙度 18 14 8 23 16 11 18 16 7 19

Averaged smoke level (HSU)

底盤馬力煙度測試 (跑步機煙度測試) Lug Down Test:

經修正量度所得的最大馬力 53 53 54 54 54 54 54 55 53 54

Corrected Measured Maximum Power (kW)

100% 最大馬力速度時所量度所得的煙度 24 22 10 22 23 14 23 20 8 21

Smoke level at 100% maximum power speed (HSU)

90% 最大馬力速度時所量度所得的煙度 24 22 9 21 24 14 23 19 7 22

Smoke level at 90 % of maximum power speed (HSU)

80% 最大馬力速度時所量度所得的煙度 22 19 10 19 21 14 20 18 7 19

Smoke level at 80 % of maximum power speed (HSU)

固定車速測試 Steady State Speed Control Test:

20% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 16.4 16.4 16.4 16.4 16.4 16.4 16.4 16.4 16.4 16.4

Road Power (kW)

固定車速度時所量度得的煙度 9 7 1 8 9 4 8 6 2 8

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 6 5 2 13 9 8 7 7 4 4

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 2 2 4 15 6 4 6 7 7 7

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 322 330 365 337 310 317 344 333 373 334

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 270 262 264 257 254 252 278 258 259 267

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 64 64 55 71 71 71 49 50 52 52

Relative Humidity (%)

50% Load: 車輛速度

50 50 50 50 50 50 50 50 50 50 Vehicle Speed (kph)

固定車速度時所量度所得的馬力 41 41 41 41 41 41 41 41 41 41

Road Power (kW)

固定車速度時所量度得的煙度 15 12 5 18 17 8 18 14 5 17

Smoke level at steady state speed (HSU)

固定車速度時所量度得的碳氫化合物濃度 7 6 4 11 12 10 7 8 6 6

HC concentration at steady state speed (ppm)

固定車速度時所量度得的一氧化碳濃度 14 10 11 35 22 12 17 29 14 27

CO concentration at steady state speed (ppm)

固定車速度時所得的修正後氮化物濃度 540 544 599 524 504 539 541 533 597 541

Corrected NOx concentration at steady state speed (ppm)

固定車速度時所量度得的排放氣温度 403 378 386 364 351 323 349 369 367 370

Exhaust Gas Temperature at steady state speed (℃)

相對濕度 64 55 64 71 71 71 49 50 52 52

Relative Humidity (%)

Table 8.10. Main dynamometer test result – M10

Page 49: Motor Fuel in Hong Kong (Final Report)

Change in Maximum Engine Power Change in Smoke Level – FAS Change in Smoke Level – Diesel Lug Down Vehicle No. (kW) (HSU) (HSU)

B20 B100 B20 B100 B20 B1000M1 -1 -9 -20 -9 -241M2 -1 0 -7 -9 -24-1M3 -4 -8 -20 -9 -29-3M4 -5 10 -15 -3 -10

M5 0 3 -4 -3 -5 -11-1M6 -1 -2 -12 -1 -17

M7 -1 -3 -3 -11 -3 -8-1M8 -3 -2 -8 -3 -20-4M9 -5 -8 -23 -5 -160M10 0 -4 -11 -1 -12

20% Load 50%Load Vehicle No. Change in CO (ppm) Change in HC (ppm) Change in NOx (ppm) Change in CO (ppm) Change in HC (ppm) Change in NOx (ppm)

B20 B100 B20 B100 B20 B100 B20 B100 B20 B100 B20 B100 M1 -42 -92 0 -6 9 90 -34 -60 2 -1 -3 17 M2 -1 2 -4 -3 -38 16 -2 -2 -4 -4 -16 16 M3 -18 20 3 3 -45 -5 -8 -6 3 -1 -12 11 M4 -67 -116 -4 -11 -9 -9 -12 -24 -2 -6 6 48 M5 0 2 -4 -2 13 36 -198 -460 2 1 3 19 M6 -5 -33 0 -2 17 42 21 -127 -3 -24 1 -54 M7 -18 -30 -3 -7 9 21 3 -10 -4 -15 8 44 M8 -24 -76 -3 -18 -11 49 -129 -451 -8 -24 7 159 M9 -9 -3 0 -4 17 90 -20 -22 1 -4 37 176 M10 -3 -3 -2 -4 -10 17 -2 -10 0 -2 -9 42

Table 8.11. Change in engine power, smoke level and gaseous pollutant concentration – Biodiesel blends Vs ULSD

Page 50: Motor Fuel in Hong Kong (Final Report)

Location Tsing Ma Tunnel Cotton Tree Drive

Test Date 9/4/01 17/4/01 24/4/01 3/4/02 4/4/02 18/4/02 13/4/02 20/4/02

Test Fuel ULSD B100 ULSD ULSD B100-A B100-B B100-C ULSD

Average of the whole journey

Kowloon to Lantau Island Kowloon to Lantau Island Kowloon to Lantau Island Cotton Tree Drive

Lantau Island Kowloon Lantau Island Kowloon Lantau Island Kowloon

Vehicle Speed (kph) 50 30 50 30 50 30 50 30 50 30 50 30 35

Smoke Level (HSU) 4 3 4 4 2 1 3 2 18 11 9 12 16

CO Concentration (ppm) 196 162 192 165 200 174 200 171 193 157 189 165 183 138 124 145 222

NOx Concentration (ppm) 291 257 320 281 322 297 346 321 260 234 275 270 293 304 312 299 283

HuRelative midity (% ) 81 81 81 81 78 78 78 78 74 78 74 78 78 78 81 72 81

Maximum of the whole journey

Vehicle Speed (kph) 35

Smoke level (HSU) 41 20 16 18 35

CO Concentration (ppm) 336 160 139 162 382

NOx Concentration (ppm) 369 390 419 398 374

Relative Humidity (%) 78 78 81 72 81

Table 9.1. On-road emission study result

Page 51: Motor Fuel in Hong Kong (Final Report)

Location Cotton Tree Drive Pokfulam Road I Pokfulam Road II Clear Water Bay I Clear Water Bay II Clear Water Bay III

Test Date 4-Sept-01 20-Aug-01 20-Aug-01 21-Aug-01 21-Aug-01 21-Aug-01

Test Fuel ULSD

Vehicle Speed (kph) 35

CO Concentration (ppm) 141 144 148 226 153 170

NOx Concentration (ppm) 280 150 213 248 211 268

Relative Humidity (%) 52 52 52 52 52 52

Table 9.2. On-road emission study – evalutation of emissions at different roads

Page 52: Motor Fuel in Hong Kong (Final Report)

R1 R2

Test Date 17-Aug-01 17-Aug-01 18-Sept-01 18-Oct-01 5-Nov-01 24-Sept-01 24-Sept-01 24-Oct-01 11-Dec-01 18-Dec-01

Test Fuel ULSD B100 ULSDULSD B100 ULSD

Free acceleration Smoke Test

Smoke Level (HSU) 26 11 12 13 44 28 8 5 4 13

Diesel Lug Down Test

MaximuCorrected m Power 45(kW) 44 43 45 45 46 45 46 48 50

Maximum Smoke Level (HSU) 24 11 11 10 21 26 6 5 4 18

Table 10.1. On-road performance test result

Page 53: Motor Fuel in Hong Kong (Final Report)

Survey Statistics

Large reduction

Slight reduction

No change

Slight increase

Large increase

KD38xx (B100 Vs ULSD)

Road Power

8 4 Smoke Opacity 1 9 2 Fuel Consumption 5 3 3 Lubricant Loss 1 10 1 Engine Noise 9 3 Lubricant Property 1 11 Overall Performance (B100 Vs ULSD) 1 10 1

GC92xx (B100 Vs ULSD)

Road Power 7 2 Smoke Opacity 9 1 Fuel Consumption 2 5 3Lubricant Loss 10Engine Noise 5 5 Lubricant Property 10 Overall Performance (B100 Vs ULSD) 2 7

Overall Averaged (B100 Vs ULDS)

Road Power 0 15 6 0 0Smoke Opacity 10 10 2 0 0Fuel Consumption 0 5 5 8 3Lubricant Loss 0 1 20 1 0Engine Noise 5 14 3 0 0Lubricant Property 0 1 21 0 0Overall Performance (B100 Vs ULSD) 3 0 17 0 1

% Population (B100 Vs ULSD)

Road Power 71.4% 28.6% Smoke Opacity 45.5% 45.5% 9.1%

Fuel Consumption 23.8% 23.8% 38.1% 14.3%Lubricant Loss 4.5% 90.9% 4.5% Engine Noise 22.7% 63.6% 13.6% Lubricant Property 4.5% 95.5% Overall Performance (B100 Vs ULSD) 14.3% 81.0% 4.8%

Table 10.2. Summary of the questionnaire survey results

Page 54: Motor Fuel in Hong Kong (Final Report)

Maximum

Engine Power

Smoke

(FAS)

Smoke

(Lug down) CO HC NOx

B20 -1% -11% -16% -14% -14% 0%

B100 -3% -44% -58% -23% -40% +9%

Table 11.1 Average percentage change for all vehicles tested

54

Page 55: Motor Fuel in Hong Kong (Final Report)

Figures

55

Page 56: Motor Fuel in Hong Kong (Final Report)

MGV Biodiesel B

0

200

400

600

800

1000

1200

1400

1600

1800

1 21 41 61 81 101 121 141 161 181 201

Time (s)

Con

cent

ratio

n (p

pm)

0

50

100

150

200

250

300

350

400

Exha

ust T

empe

ratu

re (C

)

HC CO (ppm) NOx (ppm) Exhaust Temperature

Figure 5.1. Vehicle exhaust temperature and pollutant concentration of steady state test

56

Page 57: Motor Fuel in Hong Kong (Final Report)

0

50

100

150

200

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Maximum Road Power (Diesel Lug Down) - B20 & B100

Pow

er (

kW)

ULSD

B20

B100

(a)

(-1 to 1 kW)

(0 to 1 kW)

(-5 to 4 kW)

(-1 to -4 kW)

(0 to 0 kW)

(0 to -2 kW)

(0 to -2 kW)

(0 to -1 kW)

(-2 to -8 kW)

(0 to 1 kW)

-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Maximum Road Power Variation (Diesel Lug Down Test) - B20

Perc

enta

ge C

hang

e (%

)

(b)

(-1 to 1 kW)

(-2 to -7 kW)

(-2 to -5 kW)

(-2 to -4 kW)

(-1 to -2 kW)

(2 to 3 kW)

(-3 to -6 kW)

(-2 to -5 kW)

(0 to -2 kW)

(0 to -2 kW)-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Maximum Road Power Variation (Diesel Lug Down Test) - B100

Perc

enta

ge C

hang

e (%

)

(c)

-1% -3%

-20%

-10%

0%

10%

20%

B20 B100

Overall Maximum Road Power Variation (Diesel Lug Down Test)

Perc

enta

ge C

hang

e (%

)

(d)

Figure 8.1. Maximum road power and its percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

57

Page 58: Motor Fuel in Hong Kong (Final Report)

0

20

40

60

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Smoke Level (FAS) - B20 & B100

Smok

e L

evel

(H

SU) ULSD

B20

B100

(a)

(-8 to -10 HSU)

(0 to 1 HSU)

(-1 to -15 HSU)

(8 to 12 HSU)

(-3 to -5 HSU)

(-2 to -2 HSU)

(-2 to -3 HSU)

(-2 to -3 HSU)

(-5 to -12 HSU)

(-2 to -7 kW)

-100%

-50%

0%

50%

100%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Smoke Level Variation (FAS) - B20

Perc

enta

ge C

hang

e (%

)

(b)

(-10 to -12 HSU)

(-19 to -26 HSU)

(-7 to -10 HSU)

(-10 to -11 HSU)

(-9 to -16 HSU)

(0 to -6 HSU)

(-11 to -19 HSU)

(-14 to -27 HSU)

(-5 to -9 HSU)

(-17 to -23 HSU)-100%

-50%

0%

50%

100%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Smoke Level Variation (FAS) - B100

Perc

enta

ge C

hang

e (%

)

(c)

-11%

-44%

-100%

-50%

0%

50%

100%

B20 B100

Overall Smoke Level Variation (FAS)

Perc

enta

ge C

hang

e (%

)

(d)

Figure 8.2(i). FAS smoke opacity and its percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

58

Page 59: Motor Fuel in Hong Kong (Final Report)

0

20

40

60

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Smoke Level (Diesel Lug Down) - B20 & B100

Smok

e L

evel

(H

SU) ULSD

B20

B100

(a)

(-3 to 2 HSU)

(0 to -10 HSU)

(-2 to -3 HSU)

(-2 to -4 HSU)

(-2 to 1 HSU)

(-1 to -8 HSU)

(-2 to -3 HSU)

(-8 to -9 HSU)

(-9 to -9 HSU)

(-8 to -10 HSU)-100%

-50%

0%

50%

100%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Smoke Level Variation (Diesel Lug Down Test) - B20

Perc

enta

ge C

hang

e (%

)

(b)

(-22 to -26 HSU)

(-22 to -25 HSU)

(-27 to -30 HSU)

(-7 to -13 HSU)

(-8 to -13 HSU)

(-16 to -20 HSU)

(-7 to -9 HSU)

(-15 to -25 HSU)

(-14 to -18 HSU)

(-8 to -15 HSU)

-100%

-50%

0%

50%

100%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage Smoke Level Variation (Diesel Lug Down Test) - B100

Perc

enta

ge C

hang

e (%

)

(c)

-16%

-58%-100%

-50%

0%

50%

100%

B20 B100

Overall Smoke Level Variation (Diesel Lug Down Test)

Perc

enta

ge C

hang

e (%

)

(d)

Figure 8.2(ii). Diesel lug down smoke opacity and its percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

59

Page 60: Motor Fuel in Hong Kong (Final Report)

0

100

200

300

400

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

CO Concentration - B20 & B100 (20% Load)

Con

cent

ratio

n (p

pm) ULSD

B20

B100

(a)

0

300

600

900

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

CO Concentration - B20 & B100 (50% Load)

Con

cent

ratio

n (p

pm) ULSD

B20

B100

(b)

(-9 to 1 ppm)

(-28 to 3 ppm)

(-14 to -30 ppm)

(-14 to -23 ppm)

(-17 to 6 ppm)

(-2 to 1 ppm)

(-65 to -68 ppm)

(-58 to 22 ppm)

(0 to -2 ppm)

(-24 to -60 ppm)-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage CO Variation - B20 (20% Load)

Perc

enta

ge C

hang

e (%

)

(c)

(-33 to -36 ppm)

(-2 to -3 ppm)

(0 to -17 ppm)

(-7 to -17 ppm)

(-181 to -216 ppm)

(-61 to 137 ppm)

(-4 to 8 ppm)

(-90 to -185 ppm)

(-14 to -24 ppm)

(-12 to 11 ppm)

-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage CO Variation - B20 (50% Load)

Perc

enta

ge C

hang

e (%

)

(d)

60

Page 61: Motor Fuel in Hong Kong (Final Report)

(-74 to -111 ppm)

(-2 to 6 ppm)

(-48 to 89 ppm)

(-107 to -125 ppm)

(1 to 2 ppm)

(-26 to -43 ppm)

(-22 to -46 ppm)

(-52 to -123 ppm)

(-30 to 23 ppm)

(-11 to 2 ppm)

-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage CO Variation - B100 (20% Load)

Perc

enta

ge C

hang

e (%

)

(e)

(-3 to -22 ppm)

(-18 to -28 ppm)

(-342 to -541 ppm)

(-4 to -13 ppm)

(-8 to -291 ppm)

(-406 to -513 ppm)

(-12 to -36 ppm)

(-24 to 11 ppm)

(-4 to 1 ppm)

(-53 to -67 ppm)-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage CO Variation - B100 (50% Load)

Perc

enta

ge C

hang

e (%

)

(f)

-12% -7%

-50%

-25%

0%

25%

50%

B20 B100

Overall CO Variation (20% Load)

Perc

enta

ge C

hang

e (%

)

(g)

-9% -27%

-200%

-100%

0%

100%

200%

B20 B100

Overall CO Variation (50% Load)

Perc

enta

ge C

hang

e (%

)

(h)

Figure 8.3. CO concentration and its average percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

61

Page 62: Motor Fuel in Hong Kong (Final Report)

0

25

50

75

100

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

HC Concentration - B20 & B100 (20% Load)

Con

cent

ratio

n (p

pm) ULSD

B20

B100

)

)

(a)

0

25

50

75

100

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

HC Concentration - B20 & B100 (50% Load)

Con

cent

ratio

n (p

pm) ULSD

B20

B100

(b)

(0 to -4 ppm

(-2 to 2 ppm)

(-2 to -6 ppm)

(-2 to -4 ppm)

(0 to 1 ppm)

(-2 to -6 ppm)

(-4 to -4 ppm)

(2 to 4 ppm)

(-8 to 1 ppm)

(-6 to 6 ppm)-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage HC Variation - B20 (20% Load)

Perc

enta

ge C

hang

e (%

)

(c)

(-1 to 5 ppm)

(0 to -8 ppm)

(1 to 4 ppm)

(-1 to -3 ppm)

(0 to 4 ppm)

(-9 to 6 ppm)

(-3 to -5 ppm)

(-5 to -11 ppm)

(-1 to 2 ppm)

(-1 to 1 ppm

-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage HC Variation - B20 (50% Load)

Perc

enta

ge C

hang

e (%

)

(d)

62

Page 63: Motor Fuel in Hong Kong (Final Report)

(-2 to -11 ppm)

(0 to -6 ppm)

(0 to 6 ppm)

(-5 to -16 ppm)

(0 to -5 ppm)

(0 to -4 ppm)

(-7 to -8 ppm)

(-12 to -20 ppm)

(-3 to -4 ppm)

(-3 to -4 ppm)

-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage HC Variation - B100 (20% Load)

Perc

enta

ge C

hang

e (%

)

(e)

(-1 to -2 ppm)

(-1 to -6 ppm)

(-3 to 2 ppm)

(-5 to -7 ppm)

(0 to 2 ppm)

(-18 to -32 ppm)

(-13 to -17 ppm)

(-20 to -27 ppm)

(-2 to -6 ppm)

(0 to -4 ppm)

-200%

-100%

0%

100%

200%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage HC Variation - B100 (50% Load)

Perc

enta

ge C

hang

e (%

)

(f)

-12%-30%

-100%

-50%

0%

50%

100%

B20 B100

Overall HC Variation (20% Load)

Perc

enta

ge C

hang

e (%

)

(g)

-1%

-26%

-100%

-50%

0%

50%

100%

B20 B100

Overall HC Variation (50% Load)

Perc

enta

ge C

hang

e (%

)

(h)

Figure 8.4. HC concentration and its average percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

63

Page 64: Motor Fuel in Hong Kong (Final Report)

0

300

600

900

1200

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

NOx Concentration - B20 & B100 (20% Load)

Con

cent

ration

(pp

m) ULSD

B20

B100

(a)

0

500

1000

1500

2000

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

NOx Concentration - B20 & B100 (50% Load)

Con

cent

ratio

n (p

pm) ULSD

B20

B100

(b)

(-27 to 8 ppm)

(0 to 33 ppm)

(-5 to -28 ppm)

(-1 to 18 ppm)

(6 to 40 ppm)

(9 to 18 ppm)

(-34 to 16 ppm)

(-20 to -70 ppm)

(-13 to -63 ppm)

(7 to 11 ppm)-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage NOx Variation - B20 (20% Load)

Perc

enta

ge C

hang

e (%

)

(c)

(-6 to 1 ppm)

(-97 to 66 ppm)

(-1 to -23 ppm)

(4 to 8 ppm)

(3 to 3 ppm)

(-52 to 39 ppm)

(4 to 26 ppm)

(-3 to 26 ppm)

(17 to 77 ppm)

(-23 to 4 ppm)

-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage NOx Variation - B20 (50% Load)

Perc

enta

ge C

hang

e (%

)

(d)

64

Page 65: Motor Fuel in Hong Kong (Final Report)

(59 to 121 ppm)

(-31 to 63 ppm)

(-27 to 18 ppm)

(-50 to 31 ppm)

(34 to 39 ppm)

(21 to 74 ppm)

(18 to 24 ppm)

(9 to 73 ppm)

(35 to 131 ppm)

(-20 to 43 ppm)

-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage NOx Variation - B100 (20% Load)

Perc

enta

ge C

hang

e (%

)

(e)

(12 to 59 ppm)

(92 to 247 ppm)

(117 to 189 ppm)

(26 to 57 ppm)

(-7 to -116 ppm)

(12 to 25 ppm)

(37 to 58 ppm)

(-12 to -34 ppm)

(-104 to 135 ppm)

(-5 to 39 ppm)-50%

-25%

0%

25%

50%

M1 M2 M3 M4 M5 M6 M7 M8 M9 M10

Percentage NOx Variation - B100 (50% Load)

Perc

enta

ge C

hang

e (%

)

(f)

1%9%

-50%

-25%

0%

25%

50%

B20 B100

Overall NOx Variation (20% Load)

Perc

enta

ge C

hang

e (%

)

(g)

0% 6%

-50%

-25%

0%

25%

50%

B20 B100

Overall NOx Variation (50% Load)

Perc

enta

ge C

hang

e (%

)

(h)

Figure 8.5. NOx concentration and its average percentage variation of all vehicles

Note: The numbers inside the brackets represent the range of variation in actual engineering

unit for individual vehicle

65

Page 66: Motor Fuel in Hong Kong (Final Report)

Average of the whole journey

0

200

400

600

ULSD B100 B iodiesel A B100 B iodiesel B B100 B iodiesel C

Smoke (HSU)

CO (ppm)

NOx (ppm)

Maximum of the whole journey

0

200

400

600

ULSD B100 B iodiesel A B100 B iodiesel B B100 B iodiesel C

Smoke (HSU)

CO (ppm)

NOx (ppm)

Figure 9.1. Average and maximum smoke level and air pollutant concentration for On-road

emission test at Cotton Tree Drive – Neat biodiesel Vs ULSD

Average of the whole journey

-80%

-40%

0%

40%

80%

Biodiesel A Biodiesel B Biodiesel C

Smoke (HSU)

CO (ppm)

NOx (ppm)

Maximum of the whole journey

-80%

-40%

0%

40%

80%

Biodiesel A Biodiesel B Biodiesel C

Smoke (HSU)

CO (ppm)

NOx (ppm)

Figure 9.2. Percentage variation of smoke level and air pollutant concentration for On-road

emission test at Cotton Tree Drive – Neat biodiesel Vs ULSD

66

Page 67: Motor Fuel in Hong Kong (Final Report)

-1% -3%

-20%

-10%

0%

10%

20%

B20 B100

Overall Maximum Road Power Variation (Diesel Lug Down Test)

Perc

enta

ge C

hang

e (%

)

(a)

-15%

-45%

-100%

-50%

0%

50%

100%

B20 B100

Overall Smoke Level Variation (FAS)

Perc

enta

ge C

hang

e (%

)

(b)

-16%

-58%-100%

-50%

0%

50%

100%

B20 B100

Overall Smoke Level Variation (Diesel Lug Down Test)

Perc

enta

ge C

hang

e (%

)

(c)

-14% -23%

-200%

-100%

0%

100%

200%

B20 B100

Overall CO Variation - t-test Significant

Perc

enta

ge C

hang

e (%

)

(d)

67

Page 68: Motor Fuel in Hong Kong (Final Report)

68

-14%-40%

-100%

-50%

0%

50%

100%

B20 B100

Overall HC Variation - t-test Significant

Perc

enta

ge C

hang

e (%

(e)

0%9%

-50%

-25%

0%

25%

50%

B20 B100

Overall NOx Variation - t-test Significant

Perc

enta

ge C

hang

e (%

)

(f)

Figure 11.1. Percentage variation of maximum road power and air pollutant concentration

(significant) for all vehicles

)