More SPICE Examples - RIT - People · PSpice Lite 9.2 is one of the OrCAD family of products, from...

© January 1, 2014 Dr. Lynn Fuller

More SPICE Examples

Rochester Institute of Technology

Microelectronic Engineering

ROCHESTER INSTITUTE OF TECHNOLOGY

MICROELECTRONIC ENGINEERING

More SPICE Examples

Dr. Lynn Fuller Electrical and Microelectronic Engineering

Rochester Institute of Technology 82 Lomb Memorial Drive Rochester, NY 14623-5604

Tel (585) 475-2035 Fax (585) 475-5041

Dr. Fuller’s Webpage: http://people.rit.edu/lffeee Email: [email protected]

Dept Webpage: http://www.microe.rit.edu

1-1-2014 SPICE_More_Examples.ppt

http://people.rit.edu/lffeee

mailto:[email protected]

http://www.microe.rit.edu/


More SPICE Examples



ADOBE PRESENTER

This PowerPoint module has been published using Adobe Presenter. Please click

on the Notes tab in the left panel to read the instructors comments for each slide.

Manually advance the slide by clicking on the play arrow or pressing the page

down key.


More SPICE Examples



OUTLINE

Introduction Voltage Controlled Resistor Voltage Variable Capacitor Clocked Data Latch 3.3 to 5.0V Digital Level Shifter Mono-stable Multi-vibrator LC Oscillator RC Oscillator Voltage Controlled Oscillator Two Phase Non Overlapping Clocks Analog Switches Level Shifter 3.3V to 5.0V DRAM Sense Amplifier OTA - Filters Vibration Energy Harvesting Solar Cell Energy Harvesting References Homework


More SPICE Examples



INTRODUCTION

PSpice Lite 9.2 is one of the OrCAD family of products, from Cadence Design Systems, Inc., offering a complete suite of electronic design tools. It is free and includes limited versions of OrCAD Capture, for schematic capture, PSpice for analog circuit simulation and Pspice A/D for mixed analog and digital circuit simulation. PSpice Lite 9.2 is limited to 64 nodes, 10 transistors, two operational amplifiers and 65 primitive digital devices. See page 35 (xxxv) of the PSpice Users Guide. LT SPICE – is a free SPICE simulator with schematic capture from Linear Technology. It is quite similar to PSpice Lite but is not limited in the number of devices or nodes. Linear Technology (LT) is one of the industry leaders in analog and digital integrated circuits. Linear Technology provides a complete set of SPICE models for LT components.


More SPICE Examples



VOLTAGE CONTROLLED RESISTOR

Voltage Controlled Resistor inside dashed box

V1 is to test I-V Characteristics


More SPICE Examples



VOLTAGE CONTROLLED RESISTOR

The green line is for control voltage=1.0 giving R=2Kohms, the blue is for control voltage=1.5 giving R=3Kohms. Imax=2Volts/2Kohms= 1.0mA Or Imax=2Volts/3Kohms= 0.66mA

Vcontrol=1.0

Vcontrol=1.5


More SPICE Examples



VOLTAGE VARIABLE CAPACITOR

http://www.beigebag.com/case_var_cap.htm


More SPICE Examples



CLOCKED DATA LATCH WITH AND-OR-INVERT GATE

VDD = 1.8 V

CLK

D

Q

CLK _ Q _

D

VDD

10 nF

CLK

D

Q

_ Q

CMOS And Or Invert Gate


More SPICE Examples



CLOCKED DATA LATCH WITH AND-OR-INVERT GATE

CMOS Clocked Data Latch using AND-OR-INV Gates

Inverter

AND-OR-INV AND-OR-INV


More SPICE Examples



3.3V to 5.0 V DIGITAL LEVEL SHIFTER

Converts 0-3.3 V digital signals to 0-5.0 volt signals (An inverter following the output may be used)

3.3v Signal

5v Signal


More SPICE Examples



MONOSTABLE MULTIVIBRATOR

VDD

C R

VDD = 5 V

Vout

V2 V3 VC 1 2 3

t

1 s

0

Vtrigger

27 kΩ

0.01 F

A short pulse will cause Vout to go high and stay high for a time determined by R and C


More SPICE Examples



LC OSCILLATOR

f = 1/(2 pi (sq root LC)) = 225 KHz

Two cycles in 0.009 ms gives 222KHz


More SPICE Examples



NMOS INVERTER WITH HYSTERESIS

M4 is used to change the threshold voltage of M3 by body effect through changing the voltage source-to-substrate of M3depending on if Vout is high or low. Transition voltage depends on direction of sweep.

Inverter on Left

Inverter on Right

V(In) From low-to-high

V(In2) From high-to-low


More SPICE Examples



CMOS INVERTER WITH HYSTERESIS

Replace the pull up resistor with PMOSFETs


More SPICE Examples



DIMENSIONS OF THE TRANSISTORS

NMOS PMOS

L 2u 2u

W 40u 40u

AD 17ux40u=680p 17ux40u=680p

AS 17ux40u=680p 17ux40u=680p

PD 2x(17u+40u)=114u 2x(17u+40u)=114u

PS 2x(17u+40u)=114u 2x(17u+40u)=114u

Right mouse click on each transistor and add these values to the properties/attributes.

Dimensions of transistors in Gate Array

W = 40 µm Ldrawn = 2.5µm Lpoly = 2.0µm Leff = 1.5 µm\ Pd=680p Ad=114u


More SPICE Examples



CMOS RC OSCILLATOR USING INVERTER W HYSTERESIS

C1=10p gives f=10MHz

C1=100p gives f= 1 MHz


More SPICE Examples



CMOS OSCILLATOR REPLACE R WITH MOSFETS

C1 = 100pF gives f=4MHz

C1 = 10pF gives f=16MHz


More SPICE Examples



VOLTAGE CONTROLLED OSCILLATOR


More SPICE Examples



ANALOG SWITCHES

For current flowing to the right (ie V1>V2) the PMOS transistor will be on if V1 is greater than the threshold voltage, the NMOS transistor will be on if V2 is <4 volts. If we are charging up a capacitor load at node 2 to 5 volts, initially current will flow through NMOS and PMOS but once V2 gets above 4 volts the NMOS will be off. If we are trying to charge up V2 to V1 = +1 volt the PMOS will never be on. A complementary situation occurs for current flow to the left. Single transistor switches can be used if we are sure the Vgs will be more than the threshold voltage for the specific circuit application. (or use larger voltages on the gates)

NMOS Vt=+1

PMOS Vt= -1

D S

I

zero

V1 V2

+5

S D


More SPICE Examples



ANALOG SWITCH

Switch Off Switch On

Analog Input V3 is a sine wave with 2.5v offset and amplitude of 2.5v

When V2 is low the switch is on


More SPICE Examples



ANALOG SWITCH FOR DUAL SUPPLY

This example is for a mixed digital and analog circuit. For example a 3.3 volt digital logic and +/- 5 volt analog op amp. The signal going thru the switch is +/-5 volts.

This circuit works if V3 is always positive but does not work in this example because Vin goes negative


More SPICE Examples



ANALOG SWITCH FOR DUAL SUPPLY

This example is for a mixed digital and analog circuit. For example a 3.3 volt digital logic and +/- 12 volt analog op amp.

D S

0-5V Logic Control

Vout

+5

S D Vin

+V

-V


More SPICE Examples



NON OVERLAPPING CLOCK PLUS BUFFERS

CLOCKBAR

CLOCK 1

2 t3

t2

t1

S

R

1

2


More SPICE Examples



CMOS TWO PHASE NON-OVERLAPPING CLOCK


More SPICE Examples



DRAM SENSE AMPLIFER DETAILS

Digit Line Reference Digit Line

C0

Vdd/2

Vdd

Vdd/2

s

s

p

Q9 Q8

Q5

Q6

Q2 Q1

Q3 Q4

Q7 is turned on with signal p precharging the two digit lines to Vdd/2

Q7

Note: the memory is organized into two arrays so that one can be used as the reference for the other. (with basically identical digit line capacitance) WL0

Vdd/2

D0

D0*


More SPICE Examples



SENSE AMPLIFIER DETAILS

s goes high and the data in the selected memory cell is sensed. The word line WL0 goes high and the charge on selected capacitor C0 is shared with the capacitance of the digit line D0. If a “1” was stored in C0 the voltage on D0 will initially be a little higher than Vdd/2. The voltage on the reference digit line will initially be Vdd/2. The crosscoupled inverters amplify these starting voltage and bring the digit line D0 to Vdd and D0* to zero volts. The capacitor C0 is recharged (refreshed) at the same time it is read. If a “0” was stored in C0 the voltage on D0 will initially be a little lower than Vdd/2. The crosscoupled inverters bring D0 to zero volts, refreshing C0 and providing a one for an output on D0*.


More SPICE Examples



SENSE AMPLIFER WAVEFORMS

D0

D0*

s

s


More SPICE Examples



OPERATIONAL TRANSCONDUCTANCE AMPLIFIER

+V

-V

Vin+ Vin-

M1 M2

M3

M5

M4

CMOS Realization

5

1

2

4

Va +

V- Ibias

V+

Vb Iout

-

Va +

Vb

Iout

- Ibias

Iout

gm(Va-Vb) Vref

M3 M4

Note: gm is set by Ibias


More SPICE Examples



SPICE OF OPERATIONAL TRANSCONDUCTANCE AMP


More SPICE Examples



TRANSCONDUCTANCE FOR Vref=2,3,4 volts

Iout versus Vin Gm = slope of Iout vs Vin

Gm and Ibias


More SPICE Examples



BIQUAD FILTER

VC

+

V- Ibias1

V+

-

+

V- Ibias3

V+

Vout -

VA +

V- Ibias5

V+

-

+

V- Ibias2

V+

-

C2

C1

VB +

V- Ibias4

V+

-

gm1

gm4

gm3 gm2

gm5


More SPICE Examples



BIQUAD FILTER

Vout = (s2C1C2Vc + s C1 gm4 Vb + gm2 gm5 Va)/(s2C1C2+ sC1gm3+gm2gm1)

This filter can be used as a low-pass, high-pass, bandpass, bandrejection and all pass filter. Depending on the C and gm values a Butterworth, Chebyshev, Elliptic or any other configuration can be achieved For example: let Vc=Vb=0 and Va=Vin, also let all gm be equal, then Vout = Vin / (s2C1C2/ gmgm + sC1/gm + 1) which is a second order low pass filter with corner frequency at c = gm / C1C2 and Q = C2/C1


More SPICE Examples



COMPARISON OF DIFFERENT FILTER DESIGNS

Elliptic

Butterworth

Chebychev

gain

frequency

Lowpass Filters

Elliptic is flat in the band pass region, has the steepest transition to band stop region but has some gain in the band stop region

Butterworth is flat in the band pass region, has the least steep transition to band stop region

Chebychev is not flat in the band pass region, has a steeper transition to band stop region than Butterworth


More SPICE Examples



ELLIPTIC FILTER

VC=Vin/31

+

V- Ibias

V+

-

+

V- Ibias

V+

Vout -

Vin +

V- Ibias

V+

-

+

V- Ibias

V+

-

C2

C1

R2 R1

1500

50

Vin VA


More SPICE Examples



VIBRATION ENERGY HARVESTER

5V / 0.035F


More SPICE Examples



VOLTAGE MULTIPLIER


More SPICE Examples



IXOLAR SOLAR CELL – MEASURED CHARACTERISTICS

IXOLAR – KXOB22-12X1

MEASURED ISC Cell 1 Cell2 Measured Light Intensity Room Light at Desk Top 0.0705mA 0.0509mA 300 Lux Close to Light Fixture 1.574mA 1.560mA XXX Lux Highest Microscope Illuminator Setting 51.2mA 48.6mA XXX Lux Overhead Projector 13.6mA 15mA XX Lux (~2.5mW/cm2) Direct Sunlight Through Window 16.0mA 16.0mA 65,000 Lux Dark Current 58.1nA 17.8nA zero Series Resistance 1.6966Ω 1.5363Ω Parallel Resistance >1MEG >1MEG

(~25w/m2 = ~2.5mW/cm2)


More SPICE Examples



EXTRACT SPICE MODEL FROM I-V CHARACTERISTICS

SPICE MODEL Dark Current IS = 10nA R shunt = 1/slope = 1/1.05u = ~1 MEG ohm R series = 1/slope = 1/0.1458 = 6.86 ohm


More SPICE Examples



LTSPICE SIMULATION OF 7MMX22MM SOLAR CELL


More SPICE Examples



BLOCK DIAGRAM FOR LTC3105


More SPICE Examples



LTC3105 OUTPUT VOLTAGE AND INDUCTOR CURRENT

Simulation with minimum photocurrent that works Photocurrent = 1.6 mA Rs = 1.6 ohms Rp = infinity

LTC3105 DC-to-DC Converter


More SPICE Examples



SIMULATION TO OPTIMIZE TO LOW LIGHT LEVELS


More SPICE Examples



SIMULATION TO OPTIMIZE TO LOW LIGHT LEVELS

V storage C4 V out LDO Illumination


More SPICE Examples



REFERENCES

1. MOSFET Modeling with SPICE, Daniel Foty, 1997, Prentice Hall, ISBN-0-13-227935-5 2. Operation and Modeling of the MOS Transistor, 2nd Edition, Yannis Tsividis,

1999, McGraw-Hill, ISBN-0-07-065523-5 3. UTMOST III Modeling Manual-Vol.1. Ch. 5. From Silvaco International. 4. ATHENA USERS Manual, From Silvaco International. 5. ATLAS USERS Manual, From Silvaco International. 6. Device Electronics for Integrated Circuits, Richard Muller and Theodore

Kamins, with Mansun Chan, 3rd Edition, John Wiley, 2003, ISBN 0-471-59398-2 7. ICCAP Manual, Hewlet Packard 8. PSpice Users Guide.


More SPICE Examples



HOMEWORK – MORE SPICE EXAMPLES

Do SPICE for one of the following: 1. Use SPICE to investigate an elliptic filter. 2. Do a SPICE simulation for an Analog Switch that can pass positive

and negative voltages. (+/-12 volts using 0- 5 volt logic) 3. Do a SPICE simulation for the two phase non-overlapping clock

circuit.

More SPICE Examples - RIT - People · PSpice Lite 9.2 is one of the OrCAD family of products, from...

Documents

Transcript of More SPICE Examples - RIT - People · PSpice Lite 9.2 is one of the OrCAD family of products, from...