Mono-Tray AluminumandSteel · Mono-Tray® AluminumandSteel Mono-Tray ... MONO - RACK MONO - MESH...
Transcript of Mono-Tray AluminumandSteel · Mono-Tray® AluminumandSteel Mono-Tray ... MONO - RACK MONO - MESH...
Page 180180
Mono-Tray® Aluminum and SteelMono-Tray® is a unique center-hung cable tray system, which provides organization and support for virtually
any cable or wiring installation. Available in both steel and aluminum, Mono-Tray® redefines
labor-saving with its versatile "lay-in feature".
Full side accessibility allows cable to be laid-in,
as opposed to the time consuming,
and potentially damaging, effects of cable
pulling required with conventional trapeze supports.
A full line of quick fittings and accessories are available to complete any installation.
UL Listed, CSA Certified. Available in Steel or Aluminum.
Page Cable Tray Style / Type Max. Width Nema Features
Page 181181
Mono-Tray® Aluminum and Steel
Features and Benefits UL Classified / CSA Certified
Accessory Quick Finder & Hardware Schedule
Load Ratings
Page Cable Tray Style / Type Max. Width Nema Features
65 Mono-Tray® Aluminum 24" (600mm) 12C Durable, all-purpose center-hung tray
66 Mono-Tray® Steel 24" (600mm) 12C Durable, all-purpose center-hung tray
67 Dual-Rail® Aluminum 36" (900mm) 12C Heavy duty 3 compartment tray
68 Dual-Rail® Steel 36" (900mm) 12C Heavy duty 3 compartment tray
69 Wall Rack Aluminum 12" (300mm) 12C Versatile wall-mounted tray
70 Wall Rack Steel 12" (300mm) 12C Versatile wall-mounted tray
69 Wall-Rack Double Tier Aluminum 12" (300mm) 12C Unique two-tiered wall mounted tray with two separate compartments
65 Mono-Tray® Aluminum Removable Rung 24" (600mm) 12C Offers the advantage of removable rungs
69 Wall-Rack Aluminum Removable Rung 12" (300mm) 12C Offers the advantage of removable rungs
65 Mono-Tray® Aluminum “L” Series 24" (600mm) 12B Light-duty center-hung tray for a variety of small project needs
69 Wall-Rack Aluminum “L” Series 12" (300mm) 12B Light-duty wall mounted tray
NOTE: 1. NEMA 12B & 12C classifications are inclusive of NEMA 12A ratings. 2. Refer to page 63 for CSA load rating data.
Accessory Quick Finder
Page Description
80 - 81 Covers and Inserts _ _ _ _- _ 32 _78 Blind End _ _ _ _- _ 40 _79 Drop Out _ _ _ _- _ 41 _75 Splice Connector _ _ _ _- _ 42 _82 Divider Strip _ _ _ _- _ 44 _78 Tray to Box Connector _ _ _ _- _ 45 _79 Conduit Bushing Dropout _ _ _ _- _ 46 _77 Wall Bracket _ _ _ _- _ 47 _74 Offset Connector (Horizontal) _ _ _ _- _ 48 _76 J-Hanger Steel _ _ _ _- _ 51 _82 Ground Strap _ _ _ _- _ 52 _76 Tray to Wall Connector _ _ _ _- _ 54 _72 Quick Tee (Horizontal) _ _ _ _- _ 55 _76 Hanger Items _ _ _ _- _ 56 _76 Stiffener Bars & Seismic Assembly _ _ _ _- _ 56 _77 Outboard Floor Support _ _ _ _- _ 60 _76 J-Hanger Aluminum _ _ _ _- _ 61 _82 Cable Roller _ _ _ _- _ 62 _74 Offset Connector (Vertical) _ _ _ _- _ 63 _74 Quick Tee (Vertical) _ _ _ _- _ 64 _75 Angle Connector (Vertical) _ _ _ _- _ 65 _75 Angle Connector (Horizontal) _ _ _ _- _ 66 _73 Quick Cross _ _ _ _- _ 69 _82 Rung Caps _ _ _ _- _ 71 _76 Wall Plate _ _ _ _- _ 75 _82 Multi-Junction Fittings _ _ _ _- _ 88 _
"6" and "7"Digit of P/N:
Accessory Quick FinderP / N Description Notes:
0800-0533 3/4" Nylon Bushing For use with bushingconnector (P/N:0100-0532)
0100-0700 Wall Spacers For use with wall rack andwall rack double tier
0100-0730 Tooth Clamp For use with divider stripand conduit bushing dropout
0200-0761 1/2" - 20 Split Nut 1/2" - 20 split to attachalong 1/2" threaded rod
0200-0720 "U" Clip (includes: screw,nut and washer)
For use with dropout fittings(aluminum tray only)
0200-0791 12-24 x 7/8" Hex HeadSelf Tapping Screw
For use with removablerungs
0800-0590 6" Long Vinyl Sleeve Used to cover threaded rod(to protect cables)
0100-0780 Aluminum Spine SectionWithout Rungs
12'- 0" (3.6m length)
0200-0780 Steel Spine SectionWithout Rungs
12'- 0" (3.6m length)
0200-0571 3/8"-16 x 2" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0572 3/8"-16 x 3 1/2" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0574 3/8"-16 x 2 1/2" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0575 3/8"-16 x 1 3/4" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0576 3/8"-16 x 4" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Mono-Tray ® Aluminum and Steel
Features and Benefits UL Classified / CSA Certified
Accessory Quick Finder & Hardware Schedule
Load RatingsPage Cable Tray Style / Type Max. Width Nema Features
186 Mono-Tray® Aluminum 24" (600mm) 12C Durable, all-purpose center-hung tray
187 Mono-Tray® Steel 24" (600mm) 12C Durable, all-purpose center-hung tray
188 Dual-Rail® Aluminum 36" (900mm) 12C Heavy duty 3 compartment tray
189 Dual-Rail® Steel 36" (900mm) 12C Heavy duty 3 compartment tray
190 Wall Rack Aluminum 12" (300mm) 12C Versatile wall-mounted tray
191 Wall Rack Steel 12" (300mm) 12C Versatile wall-mounted tray
189 Wall-Rack Double Tier Aluminum 12" (300mm) 12C Unique two-tiered wall mounted tray with two separate compartments
186 Mono-Tray® Aluminum Removable Rung 24" (600mm) 12C Offers the advantage of removable rungs
190 Wall-Rack Aluminum Removable Rung 12" (300mm) 12C Offers the advantage of removable rungs
186 Mono-Tray® Aluminum “L” Series 24" (600mm) 12B Light-duty center-hung tray for a variety of small project needs
189 Wall-Rack Aluminum “L” Series 12" (300mm) 12B Light-duty wall mounted tray
NOTE: 1. NEMA 12B & 12C classifications are inclusive of NEMA 12A ratings. 2. Refer to page 182 for CSA load rating data.
Accessory Quick Finder
Page Description
200 - 201 Covers and Inserts _ _ _ _- _ 32 _ 198 Blind End _ _ _ _- _ 40 _ 199 Drop Out _ _ _ _- _ 41 _ 195 Splice Connector _ _ _ _- _ 42 _ 202 Divider Strip _ _ _ _- _ 44 _ 198 Tray to Box Connector _ _ _ _- _ 45 _ 199 Conduit Bushing Dropout _ _ _ _- _ 46 _ 197 Wall Bracket _ _ _ _- _ 47 _ 196 Offset Connector (Horizontal) _ _ _ _- _ 48 _ 196 J-Hanger Steel _ _ _ _- _ 51 _ 202 Ground Strap _ _ _ _- _ 52 _ 196 Tray to Wall Connector _ _ _ _- _ 54 _ 192 Quick Tee (Horizontal) _ _ _ _- _ 55 _ 196 Hanger Items _ _ _ _- _ 56 _ 196 Stiffener Bars & Seismic Assembly _ _ _ _- _ 56 _ 197 Outboard Floor Support _ _ _ _- _ 60 _ 196 J-Hanger Aluminum _ _ _ _- _ 61 _ 194 Offset Connector (Vertical) _ _ _ _- _ 63 _ 194 Quick Tee (Vertical) _ _ _ _- _ 64 _ 195 Angle Connector (Vertical) _ _ _ _- _ 65 _ 195 Angle Connector (Horizontal) _ _ _ _- _ 66 _ 193 Quick Cross _ _ _ _- _ 69 _ 202 Rung Caps _ _ _ _- _ 71 _ 196 Wall Plate _ _ _ _- _ 75 _
"6" and "7"Digit of P/N:
Accessory Quick FinderP / N Description Notes:
0800-0533 3/4" Nylon Bushing For use with bushingconnector (P/N:0100-0532)
0100-0700 Wall Spacers For use with wall rack andwall rack double tier
0100-0730 Tooth Clamp For use with divider stripand conduit bushing dropout
0200-0761 1/2" - 20 Split Nut 1/2" - 20 split to attachalong 1/2" threaded rod
0200-0720 "U" Clip (includes: screw,nut and washer)
For use with dropout fittings(aluminum tray only)
0200-0791 12-24 x 7/8" Hex HeadSelf Tapping Screw
For use with removablerungs
0800-0590 6" Long Vinyl Sleeve Used to cover threaded rod(to protect cables)
0100-0780 Aluminum Spine SectionWithout Rungs
12'- 0" (3.6m length)
0200-0780 Steel Spine SectionWithout Rungs
12'- 0" (3.6m length)
0200-0571 3/8"-16 x 2" GR2 Hex Head, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0572 3/8"-16 x 3 1/2" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0574 3/8"-16 x 2 1/2" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0575 3/8"-16 x 1 3/4" GR2 HexHead, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
0200-0576 3/8"-16 x 4" GR2 Hex Head, Zinc Plated Bolt
Complete with: 3/8"-16hex nut and washer
Page 182182
Ordering Summary Guide Quick Selector
CSA Load Ratings
Example Catalog NumberBottom Rung Mono-Tray Aluminum, 3" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
TRAY STYLE TRAY TYPE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH RUNG STYLE
B 1 1 5 3 1 _0 3 2
B
L
LB
CB
BottomRung Tray
L-SeriesTop Rung
L-SeriesBottom Rung
4" HighSpine
1
2
6
9
Mono-Tray(Ladder)
Dual-Rail
Wall-Rack
Wall-RackDouble-Tier
1
2
3
4
5
6
Aluminum
Pre-GalvanizedSteel
Hot DippedGalvanizedSteel afterFabrication
Epoxy Paint(Aluminum)
Epoxy Paint(Steel)
AnodizedAluminum
R
D
RD
B
Removable1/2" (12mm)Type "C" Rung
3/4" (19mm)Type "D" Rung
Removable3/4" (19mm)Type "D" Rung
"B" Rung
6"
9"
12"
18"
3"
4"
150
225
300
450
75
100
1
2
3
4
5
6
in mm
6"
9"
12"
18"
24"
36"
3"
4"
30"
150
225
300
450
600
900
75
100
750
1
2
3
4
5
6
7
8
9
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
CSA LOAD RATING
CSALoad Class
Product LineMaximum
Rung Spacing RungStyle
MaximumTray Width
"L"-Series Mono-Tray® Aluminum 12 300 12 A, B300"L"-Series Wall-Rack Aluminum 6 150 12 A, B300
Mono-Tray® Aluminum 24 600 6 B, C150Mono-Tray® Aluminum 12 300 12 B300Mono-Tray® Aluminum 9 230 18 B450Wall-Rack Aluminum 12 300 6 C, D150
Wall-Rack Steel 12 300 6 E150Mono-Tray® Aluminum 12 300 12 B300Mono-Tray® Aluminum 18 450 9 C230Mono-Tray® Aluminum 24 600 6 C150Mono-Tray® Aluminum 24 600 12 D300
Mono-Tray® Steel 24 600 12 E300Dual-Rail® Aluminum 36 900 12 C300
Dual-Rail® Steel 36 900 12 E300
in mm in mm
A37Kg/m/3m
C197Kg/m/3m
D1179Kg/m/3m
E299Kg/m/3m
Mono-Tray® Aluminum and Steel
3" Rung spacing notavailable with "L"
Series Tray.
Page 183183
Product Reference Installation
Wall RackTray to Box Connector
Double Tier Wall Rack
HorizontalQuick Cross
Dropout
Vertical Angle Connector
Dual Rail
Splice Connector
Horizontal Pivot
Vertical Pivot
Horizontal Quick Tee
Vertical Offset
Mono-Tray
Tray to WallBlind End
Horizontal Offset
Vertical Quick Tee
Horizontal Quick Tee
Floor Supports
Covers & Inserts
Typical AluminumMono-Tray Connector Installation Typical Steel Mono-Tray Connector Installation
1/2" (12mm) Threaded Rod(by others)
1/2" (12mm) Threaded Rod(by others)
Mono-Tray® Aluminum and SteelT
RO
UG
HT
RA
YC
EN
TE
RS
PIN
EM
ON
O-
RA
CK
MO
NO
-M
ES
HP
OW
ER
-T
RA
Y
Page 184184
Mono-Tray® CB Series Aluminum Tray System
Unique Device Bracket Provides means ofmouting wiring devices at the cable tray.This method allows greater flexibility withthe location of communication drops, andprovides ease of relocation.
★NEW CB Style Tray - A Modular approach to wiring.
"D" Rung(Optional)
CBDB-431
4” High spine creates an intrinsic barrierwhich creates two generous compartmentswithin the cable tray system. Center hungdesign eliminates the need to pull delicatecommunication cabling.
4" H Spine
Page 185185
Mono-Tray® CB Series Aluminum Tray SystemT
RO
UG
HT
RA
YC
EN
TE
RS
PIN
EM
ON
O-
RA
CK
MO
NO
-M
ES
HP
OW
ER
-T
RA
Y
6 150 CB111(*)-03219 225 CB112(*)-0321
12 300 CB113(*)-032118 450 CB114(*)-03216 150 CB111(*)-03229 225 CB112(*)-0322
12 300 CB113(*)-032218 450 CB114(*)-03226 150 CB111(*)-03239 225 CB112(*)-0323
12 300 CB113(*)-032318 450 CB114(*)-03236 150 CB111(*)-03249 225 CB112(*)-0324
12 300 CB113(*)-032418 450 CB114(*)-03246 150 CB111(*)-03259 225 CB112(*)-0325
12 300 CB113(*)-032518 450 CB114(*)-0325
Catalog NumbermminRung Spacing
mminActual Width (AW)
Width
CB1 STYLE TRAY
191
267
343
450
600
7.5
10.5
13.5
18
24
6
9
12
18
24
Dimensional / Ordering Data
(*): Insert Rung Height: 3=3” (75), 4=4” (100), 6=6” (150)
CB1 Style Tray
6 150 CB211(*)-03249 225 CB212(*)-0324
12 300 CB213(*)-032418 450 CB214(*)-03246 150 CB211(*)-03259 225 CB212(*)-0325
12 300 CB213(*)-032518 450 CB214(*)-03256 150 CB211(*)-03299 225 CB212(*)-0329
12 300 CB213(*)-032918 450 CB214(*)-03296 150 CB211(*)-03269 225 CB212(*)-0326
12 300 CB213(*)-032618 450 CB214(*)-0326
Catalog NumbermminRung Spacing
mminActual Width (AW)
Width
CB2 STYLE TRAY
450
600
750
900
18
24
30
36
18
24
30
36
(*): Insert Rung Height: 3=3” (75), 4=4” (100), 6=6” (150)
CB2 Style Tray
6 150 CBA211(*)-03249 225 CBA212(*)-0324
12 300 CBA213(*)-032418 450 CBA214(*)-03246 150 CBA211(*)-03259 225 CBA212(*)-0325
12 300 CBA213(*)-032518 450 CBA214(*)-03256 150 CBA211(*)-03299 225 CBA212(*)-0329
12 300 CBA213(*)-032918 450 CBA214(*)-03296 150 CBA211(*)-03269 225 CBA212(*)-0326
12 300 CBA213(*)-032618 450 CBA214(*)-0326
Catalog NumbermminRung Spacing
mminSide (L)Rail Spacing (S)
Width
CB2 STYLE TRAY
100
178
150
225
4
7
6
9
mmin
178
178
380
380
7
7
15
15
Actual Width (W)mmin
450
600
750
900
12.5
15.5
22.5
25.5
11
14
21
24
(*): Insert Rung Height: 3=3” (75), 4=4” (100), 6=6” (150)
CBA Style Tray
Page 186186
Example Tray Catalog NumberBottom Rung Mono-Tray Aluminum, 6" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
B 1 1 1 3 1 _0 3 2
TRAY STYLE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH RUNG STYLE
B
L
LB
BottomRung Tray
Light DutyTray
L-SeriesBottom Rung
1
4
6
Aluminum
Epoxy Paint(Aluminum)
AnodizedAluminum
R
D
RD
B
Removable1/2" (12mm)Type "C" Rung
3/4" (19mm)Type "D" Rung
Removable3/4" (19mm)Type "D" Rung
"B" HollowRung
6"
9"
12"
18"
3"
4"
150
225
300
450
75
100
1
2
3
4
5
6
in mm
6"
9"
12"
18"
24"
3"
4"
150
225
300
450
600
75
100
1
2
3
4
5
7
8
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
For Standard Type “C”Aluminum Fixed Rung.
No Letter Suffixis required.
Removable Rung is notavailable for Double Tier.
3" R.S. for StandardTray Only. Not
available in "L" Series
18" R.S. only for6" & 9" widths.
12" R.S. only for6", 9" & 12" widths.
"C" Rung(Standard)
"B" Rung(Light Duty)
"D" Rung(Optional)
Mono-Tray® Aluminum
Material Data - Aluminum
Design Data
Ordering Data
One splice connector (p/n: 0100-0420) is provided with each tray length.
Support SpanSpineType
Deflection NEMA Rating
SPINE DEFLECTION @ 100#/ft (149kg/m)
12 3.6 2.8 71 12Cft m in mm (1.5 Safety Factor)
12Standard
Light 3.6 3.4 86 12B
Mono-TrayAluminum
Mono-TrayAluminum
Removable Rung
Spine(Standard Tray)
Spine(Light Duty Tray)
BOTTOM RUNGWIDTH CHART
(ALUMINUM TRAY)
6 7.5 19110.5 26713.5 34318 45024 600
WBW
in mm
9121824
(See Chart)
Note: Removable Rungutilizes screw attachment
CSACertified
Page 187187
Example Tray Catalog NumberBottom Rung Mono-Tray Steel, 6" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
B 1 2 1 3 10 3 2
TRAY STYLE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH
B BottomRung Tray
2
4
5
Pre-GalvSteel
HDGAF
Epoxy Paint(Steel)
6"
9"
12"
150
225
300
1
2
3
in mm
6"
9"
12"
18"
24"
150
225
300
450
600
1
2
3
4
5
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
3.0 Meter Lengthfor use in Canada
Mono-Tray® Steel
Material Data - Steel
Design Data
Ordering Data
One splice connector (p/n: 0200-0420) is provided with each tray length.
Rung(Standard)
Rung Caps OptionalOrder separately
Support SpanSpineType
Deflection NEMA Rating
STEEL SPINE DEFLECTION @ 100#/ft (149kg/m)
12 3.6 2.4 61 12Cft m in mm (1.5 Safety Factor)
Standard
BOTTOM RUNGWIDTH CHART(STEEL TRAY)
6 7.5 19110 25413 33018 45024 600
WBW
in mm
9121824
Spine(Standard)
CSACertified
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 188188
ft m in mm (1.5 Safety Factor)
12 3.6 2.25 71 12C
Spine Deflection @150 lbs/ft (223Kg/m)Support Span Deflection NEMA Rating
Spine Type
Standard
Dual-Rail® Aluminum
Material Data - Aluminum
Design Data
Ordering Data
Type C & Type D rungs feature box beam design for additional strength.
One splice connector (p/n: 0100-0420) is provided with each tray length.
Rung Caps OptionalOrder separately
"C" Rung(Standard)
"D" Rung(Optional)
Standard Spine
Note: Removable Rungutilizes screw attachment
Example Tray Catalog NumberBottom Rung Dual-Rail Aluminum, 6" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
B 2 1 1 3 1 _0 3 2
TRAY STYLE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH RUNG STYLE
B BottomRung Tray
1
4
6
Aluminum
Epoxy Paint(Aluminum)
AnodizedAluminum
D 3/4" (19mm)Type "D" Rung
6"
9"
12"
18"
150
225
300
450
1
2
3
4
in mm
18"
24"
36"
30"
450
600
900
750
4
5
6
9
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
For Standard Type “C”Aluminum Fixed Rung.
No Letter Suffixis required.
3.0 meter length foruse in Canada.
TrayWidth
RungSpacing
R
369
12
75150225300
in in mm
RailSpacing
S
7777
178178178178
in mm
SideSpacing
L
4444
100100100100
in mm
18
Top RungActual Width
TWTop RungCatalogNumber
Bottom RungActual Width
BWBottom Rung
CatalogNumber
18 450 18 450
2153-0324 B2153-03242113-03242123-03242133-0324
B2113-0324B2123-0324B2133-0324
369
12
75150225300
7777
178178178178
7777
178178178178
24 24 600 24 600
2153-0325 B2153-03252113-03252123-03252133-0325
B2113-0325B2123-0325B2133-0325
369
12
75150225300
15151515
380380380380
6666
150150150150
30 30 750 30 750
2153-0329 B2153-03292113-03292123-03292133-0329
B2113-0329B2123-0329B2133-0325
369
12
75150225300
15151515
380380380380
9999
225225225225
36 36 900 36 900
2153-0326 B2153-03262113-03262123-03262133-0326
B2113-0326B2123-0326B2133-0326
TOP RUNG TRAY BOTTOM RUNG TRAY
in mm in mm
DUAL-RAIL ® ALUMINUM
CSACertified
Page 189189
Dual-Rail® Steel
Material Data - Steel
Design Data
Ordering Data
Two splice connectors (p/n: 0200-0420) are provided with each tray length.
Rung(Standard)
Rung Caps OptionalOrder separately
Support SpanSpineType
Deflection NEMA Rating
STEEL SPINE DEFLECTION @ 100#/ft (149kg/m)
12 3.6 2.4 61 12Cft m in mm (1.5 Safety Factor)
Standard
Spine(Standard)
TRAY DIMENSION CHART(STEEL DUAL-RAIL)
18 7 1777 17715 38015 380
WL
in mm
4.5 1007.5 1786.5 1509.5 225
Sin mm
243036
Example Tray Catalog NumberBottom Rung Dual-Rail Steel, 6" Rung Spacing, 3" High, 12"-0" Length, 18" Wide
B 2 2 1 3 40 3 2
TRAY STYLE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH
B BottomRung Tray
2
3
5
Pre-GalvSteel
HDGAF
Epoxy Paint(Steel)
6"
9"
12"
150
225
300
1
2
3
in mm
18"
24"
36"
30"
450
600
900
750
4
5
6
9
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
3.0 Meter Lengthfor use in Canada
CSACertified
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 190190
Example Tray Catalog NumberBottom Rung Wall-Rack Aluminum, 3" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
B 6 1 5 3 1 _0 3 2
TRAY STYLE TRAY TYPE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH RUNG STYLE
B
L
LB
BottomRung Tray
Light DutySpine
Light DutyBottomRung
6
9
Wall-Rack
Wall-RackDouble-Tier
1
4
6
Aluminum
Epoxy Paint(Aluminum)
AnodizedAluminum
R
D
RD
B
Removable1/2" (12mm)Type "C" Rung
3/4" (19mm)Type "D" Rung
Removable3/4" (19mm)Type "D" Rung
"B" HollowRung
6"
9"
12"*
3"
150
225
300
75
1
2
3
5
in mm
6"
9"
12"
3"
150
225
300
75
1
2
3
7
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
For Standard Type “C”Aluminum Fixed Rung.
No Letter Suffixis required.
Removable Rungis not available for
Double Tier.
* 12" Rung Spacingis available for 3"
and 6" tray width only.
Double Tier availablein 6" and 9" Rung
Spacing only.
Wall-Rack Aluminum
Material Data - Aluminum
Design Data
Ordering Data
One splice connector (p/n: 0100-0420) is provided with each tray length. Three wall spacers are included with each length.
"C" Rung(Standard)
"B" Rung(Light Duty)
"D" Rung(Optional)
Support SpanSpineType
Deflection NEMA Rating
SPINE DEFLECTION @ 100#/ft (149kg/m)
12 3.6 2.8 71 12Cft m in mm (1.5 Safety Factor)
12Standard
Light 3.6 3.4 86 12B
Wall RackDouble-Tier
Wall Rack
Spine(Standard Tray)
Spine(Light Duty Tray)
Wall-Rack Double TierTop RungWall-Rack Aluminum Top RungWall-Rack Aluminum
3.0 meter length foruse in Canada.
CSACertified
Page 191191
Wall-Rack Steel
Material Data - Steel
Design Data
Ordering Data
One splice connector (p/n: 0200-0420) is provided with each tray length. Three wall spacers are included with each length.
Rung(Standard)
Rung Caps OptionalOrder separately
Support SpanSpineType
Deflection NEMA Rating
STEEL SPINE DEFLECTION @ 100#/ft (149kg/m)
12 3.6 2.4 61 12Cft m in mm (1.5 Safety Factor)
Standard
Spine(Standard)
Example Tray Catalog NumberBottom Rung Mono-Tray Steel, 6" Rung Spacing, 3" High, 12"-0" Length, 6" Wide
B 6 2 1 3 10 3 2
TRAY STYLE MATERIAL RUNG SPACING RUNG HEIGHT TRAY LENGTH TRAY WIDTH
B BottomRung Tray
2
3
5
Pre-GalvSteel
HDGAF
Epoxy Paint(Steel)
6"
9"
12"
150
225
300
1
2
3
in mm
6"
9"
12"
18"
24"
150
225
300
450
600
1
2
3
4
5
in mm
3"
4"
6"
75
100
150
3
4
6
12'
10'
3.6
3.0
32
35
in mm ft m
For Top RungStandard Spine Tray
No Letter Prefixis required.
3.0 Meter Lengthfor use in Canada
CSACertified
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 192192
Quick Fittings Horizontal Quick Tees
BottomRung Horizontal Quick Tee
• Quickly creates a 90˚ right angle tee or elbow.
• May be used with top or bottom rung cable tray of all heights.
• For use with Mono-Tray®, Dual-Tray®, and Wall Rack Cable Tray.(For Dual-Rail® specify two Quick Tees).
• May also be used to accomplish 90˚ elbows when installed atend of cable tray run.
• For steel cable tray utilize bottom rung quick tees for both topand bottom rung applications.
BOTTOM RUNG HORIZONTAL QUICK TEE SELECTOR
B0100-0557 B0200-0557
WALL RACK MONO-TRAY® DUAL-RAIL®TrayWidth(in)
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
3B0100-0551 B0200-05516 B0100-0557 B0200-0557
B0100-0550 B0200-0550B0100-0551 B0200-0551B0100-0552 B0200-0552B0100-0553 B0200-0553
B0100-0550 B0200-0550B0100-0551 B0200-0551B0100-0551 B0200-0551B0100-0552 B0200-0552
B0100-0552 B0200-05529B0100-0553 B0200-055312
18243036
BOTTOM RUNG HORIZONTAL QUICK TEEDIMENSIONAL INFORMATION
B0100-0557 B0200-0557 3 754.5 1126 1509 225
12 300
AluminumTrayP/N
SteelTrayP/N
Part WidthW
in mm
B0100-0550 B0200-0550B0100-0551 B0200-0551B0100-0552 B0200-0552B0100-0553 B0200-0553
NOTE: Nuts, bolts, & washers provided
Top Rung Horizontal Quick Tee
• Quickly creates a 90˚ right angle tee or elbow.
• May be used with top rung cable tray of all heights.
• (For Dual-Rail® specify two Quick Tees).
• For steel cable tray utilize bottom rung quick tees for both topand bottom rung applications.
TOP RUNG HORIZONTAL QUICK TEEDIMENSIONAL INFORMATION
0100-0557 N/A* 3 754.5 1126 1509 225
12 300
AluminumTrayP/N
SteelTrayP/N
Part WidthW
in mm
0100-0550 N/A*0100-0551 N/A*0100-0552 N/A*0100-0553 N/A*
NOTE: Nuts, bolts, & washers provided
TOP RUNG HORIZONTAL QUICK TEE SELECTOR
0100-0557
WALL RACK MONO-TRAY® DUAL-RAIL®TrayWidth(in)
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
30100-05516 0100-0557
0100-05500100-05510100-05520100-0553
0100-05500100-05510100-05510100-0553
0100-055290100-055312
18243036
An effective method for creating horizontal tees anywhere in a cable tray system.
Note: Add prefix "C" for 4" High Spine.
Page 193193
Quick Fittings Horizontal Quick Crosses
Bottom Rung Horizontal Quick Cross
• Quickly creates a 90˚ horizontal cross.
• May be used with top or bottom rung tray of all heights.
• For use with Mono-Tray®, and Wall Rack Cable Tray. Not to beused for Dual-Rail® Tray. Dual-Rail® Crosses are accomplishedby utilizing quick tees. (page192).
• For steel tray utilize bottom rung quick tees for both topand bottom rung applications.
BOTTOM RUNG HORIZONTAL QUICK CROSS SELECTOR
B0100-0697 B0200-0697
WALL RACK MONO-TRAY® DUAL-RAIL®TrayWidth(in)
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
3B0100-0691 B0200-06916 B0100-0691 B0200-0691
B0100-0692 B0200-0692B0100-0693 B0200-0693B0100-0694 B0200-0694B0100-0695 B0200-0695
B0100-0692 B0200-06929B0100-0693 B0200-069312
18243036
BOTTOM RUNG HORIZONTAL QUICKCROSS DIMENSIONAL INFORMATION
B0100-0691 B0200-0691 6 1509 225
12 30018 45024 600
AluminumTrayP/N
SteelTrayP/N
Part WidthW
in mm
B0100-0692 B0200-0692B0100-0693 B0200-0693B0100-0694 B0200-0694B0100-0695 B0200-0695
NOTE: Nuts, bolts, & washers provided
Top Rung Horizontal Quick Cross
• Quickly creates a 90˚ cross.• For use with top rung aluminum Mono-Tray®, and Wall Rack
Cable Tray. Not to be used for Dual-Rail® cable tray. Dual-Rail®
Crosses are accomplished by utilizing quick tees. (page 192).
• For steel tray utilize bottom rung quick tees for both topand bottom rung applications.
TOP RUNG HORIZONTAL QUICK CROSSDIMENSIONAL INFORMATION
0100-0691 N/A* 6 1509 225
12 30018 45024 600
AluminumTrayP/N
SteelTrayP/N
Part WidthW
in mm
0100-0692 N/A*0100-0693 N/A*0100-0694 N/A*0100-0695 N/A*
NOTE: Nuts, bolts, & washers provided
TOP RUNG HORIZONTAL QUICK CROSS SELECTOR
0100-0697
WALL RACK MONO-TRAY® DUAL-RAIL®TrayWidth(in)
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
AluminumTray P/N
SteelTray P/N
30100-06916 0100-0691
0100-06920100-06930100-06940100-0695
0100-069290100-069312
18243036
An effective method for creating horizontal crosses anywhere in a cable tray system.
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 194194
Page 195195
Page 196196
Support & Installation Accessories
Hangers & Wall Connectors Note: All hanging hardware and 1/2" (12mm) support rods by others.
J-HangerFor supporting tray at any point alonghorizontal run. Threaded hanger rod byothers. Overall height: 7.5" (190mm).Plated finish.
AluminumTray P/N
SteelTray P/N
0200-0610 0200-0610
Quick-StrapHangerFor supporting aluminum tray at any pointalong horizontal run. No drilling necessaryThreaded hanger rod by others. Plated finish.
AluminumTray P/N
0200-0615
Wall PlateConnectorFor wall termination and stabilization ofcable tray run. Wall fasteners by others.Mounting holes: four 7/16" (11mm).Plated finish.
AluminumTray P/N
SteelTray P/N
0100-0750 0200-0750
Tray to WallConnectorAttach end of aluminum cable tray run toany surface. For steel tray see wall plateconnector. (P/N: 0200-0750).
AluminumTray P/N
0100-0540
Stiffeners & Restraints Note: All hanging hardware and 1/2" (12mm) support rods by others.
Seismic BraceFor utilization in geographic areas ofseismic activities. Bracing materialsby others.
AluminumTray P/N
SteelTray P/N
0200-0565 0200-0567
Universal Stiffener
Stabilizes eccentrically loaded cable tray.Specify two universal stiffeners. Use withaluminum or steel tray.
P/N0200-0569
Page 197197
Support & Installation Accessories
Wall Supports Allow center-hung tray to be conveniently mounted on walls or structures.
Mono-Tray®
Wall Support
7/16" diameter (11mm) mounting holesprovide quick and easy mounting ofMono-Tray® cable tray. Tray may bemounted above or hung below wallsupport. Material: Aluminum.
Dual-Rail®
Wall Support7/16" diameter (11mm) mounting holesprovide quick and easy mounting ofDual-Rail® cable tray. Tray may bemounted above or hung below wallsupport. Material: Aluminum.
Floor Supports Support cable tray system on floor applications.
Floor Supports
Outboard floor supports add to the versatility of Mono-Systems, Inc. Cable Tray Systems.
Cable tray has traditionally been only installed above ceilings or suspended from building
structures. Outboard floor supports provide a simple and effective method for installing
cable tray under raised computer room floors, on floors near industrial or mechanical
equipment, in tunnels, and in communications rooms.
Type 2For use with top rung tray only. Designprovides stabilization of cable tray.3 - 7/16" dia. (11) mounting holes.
AluminumTray P/N
SteelTray P/N
0100-0600-2-(H) 0200-0600-2-(H)
Type 3For use with top and bottom rung tray.3 - 7/16" dia. (11) mounting holes.
AluminumTray P/N
SteelTray P/N
0100-0600-3-(H) 0100-0600-3-(H)
MONO-TRAY®
WALL SUPPORT
6 0100-04779 0100-0470
12 0100-047118 0100-047224 0100-0473
Tray Width Part Number
DUAL-RAIL®
WALL SUPPORT
18 2100-047424 2100-047530 2100-047936 2100-0476
Tray Width Part Number
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 198198
Support & Installation Accessories
Tray to Box Connectors Use for smooth penetrations into boxes or through walls.
MONO-TRAY®
TRAY TO BOX CONNECTOR
6 0103-0451
TrayWidth
(in)
Top RungAluminum Tray
P/N
9 0103-045212 0103-045318 0103-045424 0103-0455
0203-0451
Top RungSteel Tray
P/N
0203-04520203-04530203-04540203-0455
B0103-0451
Bottom RungAluminum Tray
P/N
B0103-0452B0103-0453B0103-0454B0103-0455
B0203-0451
Top RungSteel Tray
P/N
B0203-0452B0203-0453B0203-0454B0203-0455
Mono-Tray® & Wall Rack Tray to Box Connector
For Wall Rack & Wall Rack double-tier add -LH or -RH suffix to part number for left hand or right hand configuration. Change fourth digit of part number to 4 for4" (100mm) rung height.Change fourth digit of part number to 6 for6" (150mm) rung height.
Dual-Rail® Tray to Box Connector
Change fourth digit of part number to 4 for4" (100mm) rung height.Change fourth digit of part number to 6 for6" (150mm) rung height.
Left-handshown
DUAL-RAIL®
TRAY TO BOX CONNECTOR
18 2103-0454
TrayWidth
(in)
Top RungAluminum Tray
P/N
24 2103-045530 2103-045936 2103-0456
2203-0454
Top RungSteel Tray
P/N
2203-04552203-04592203-0456
B2103-0454
Bottom RungAluminum Tray
P/N
B2103-0455B2103-0459B2103-0456
B2203-0454
Top RungSteel Tray
P/N
B2203-0455B2203-0459B2203-0456
Blind Ends Cleanly terminates runs of cable tray.
MONO-TRAY®
BLIND END
6 0103-0401
TrayWidth
(in)
Top RungAluminum Tray
P/N
9 0103-040212 0103-040318 0103-040424 0103-0405
0203-0401
Top RungSteel Tray
P/N
0203-04020203-04030203-04040203-0405
B0103-0401
Bottom RungAluminum Tray
P/N
B0103-0402B0103-0403B0103-0404B0103-0405
B0203-0401
Top RungSteel Tray
P/N
B0203-0402B0203-0403B0203-0404B0203-0405
Mono-Tray® & Wall Rack Blind End
For Wall Rack & Wall Rack double-tier add -LH or -RH suffix to part number for left hand or right hand configuration. Change fourth digit of part number to 4 for4" (100mm) rung height.Change fourth digit of part number to 6 for6" (150mm) rung height.
Dual-Rail® Blind End
Change fourth digit of part number to 4 for4" (100mm) rung height.Change fourth digit of part number to 6 for6" (150mm) rung height.
Left-handshown
DUAL-RAIL®
BLIND END
18 2103-0404
TrayWidth
(in)
Top RungAluminum Tray
P/N
24 2103-040530 2103-040936 2103-0406
2203-0404
Top RungSteel Tray
P/N
2203-04052203-04092203-0406
B2103-0404
Bottom RungAluminum Tray
P/N
B2103-0405B2103-0409B2103-0406
B2203-0404
Top RungSteel Tray
P/N
B2203-0405B2203-0409B2203-0406
Page 199199
Support & Installation Accessories
Conduit Bushing Dropout Integrate conduit and Mono-Systems, Inc. cable tray into one system.
For attaching conduit to cable tray.
Trade size openings allow for easy
attachment of many types of con-
duit bushings (conduit bushings
supplied by others. Tooth clamps
and/or screws are provided for
attachment.
Dropouts
Spine Bracket
An effective method of dropping cable bundles out of cable tray system.
Mono-Tray® Dropout
NOTE: Aluminum tray dropouts shown. Steel tray dropouts install using self-tapping screw (supplied).
Dual-Rail® Dropout
For full width Mono-Tray® Dropouts, specify2 dropouts for desired tray width.
CONDUITDROPOUT
3 75469
1218
5
RungSpacing
in mm
Change 3rdDigit ofP/N to:
100 6150 1225 2300 3450 4
CONDUIT DROPOUT
1/2 133/4
11 1/4
1 1/2
22 1/2
33 1/2
0100-0460
ConduitDiameterin mm
Aluminum TrayP/N
0200-046019 0100-0461 0200-046125 0100-0462 0200-046232 0100-0463 0200-046338 0100-0464 0200-046451 0100-0465 0200-046564 0100-0466 0200-046675 0100-0467 0200-046789 0100-0468 0200-0468102 0100-0469 0200-0469
Steel TrayP/N
4
MONO-TRAY®
DROPOUT
6 1.25 322.75 704.25 1087.25 184
10.25 260
TrayWidth
in
Part WidthW
in mm
9121824
0100-0417
AluminumCatalogNumber
SteelCatalogNumber
0100-04100100-04110100-04120100-0413
0200-04170200-04100200-04110200-04120200-0413
DUAL-RAIL®
DROPOUT
18 3 766 1525 1278 203
TrayWidth
in
Outside DropoutWidth (A)in mm
243036
2100-0418
AluminumTray P/N(Outside)
SteelTray P/N(Outside)
2100-04182100-04172100-0410
2200-04182200-04182200-04172200-0410
6.88 1756.88 175
14.88 37814.88 378
Inside DropoutWidth (B)in mm
2100-0417
AluminumTray P/N(Inside)
SteelTray P/N(Inside)
2100-04172100-04112100-0411
2200-04122200-04122200-04092200-0409
For full width Dual-Rail® Dropouts,specify 2 dropouts for desired traywidth.
Snap-on bracket installs quickly,and provides attachment of a widevariety of device boxes to 4" highspine.
★NEW
4" HighSpine Bracket
CBDB-431
StandardSpine Bracket
MTDB-431
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Also available for standardMono-Tray Aluminum Spine!
Page 200200
Covers & Inserts
Covers
MONO-TRAY®
SOLID COVER
6 3100-0321
TrayWidth
(in)
Top RungAluminum Tray
P/N
9 3100-032212 3100-032318 3100-032424 3100-0325
3200-0321
Top RungSteel Tray
P/N
3200-03223200-03233200-03243200-0325
B3100-0321
Bottom RungAluminum Tray
P/N
B3100-0322B3100-0323B3100-0324B3100-0325
B3200-0321
Bottom RungSteel Tray
P/N
B3200-0322B3200-0323B3200-0324B3200-0325
Mono-Tray® Solid Cover
• Standard 12'-0" (3.6m) length. Canadian orders (3m length)change seventh digit of part number to 5.
• All aluminum tray covers shown are made of aluminum.
• All steel covers shown are made of galvanized steel.
DUAL-RAIL®
SOLID COVER
18 3100-0324
TrayWidth
(in)
Top RungAluminum Tray
P/N
24 3100-032530 3100-032936 3100-0326
3200-0324
Top RungSteel Tray
P/N
3200-03253200-03293200-0326
B3200-0324
Bottom RungAluminum Tray
P/N
B3200-0325B3200-0329B3200-0326
B3100-0324
Bottom RungSteel Tray
P/N
B3100-0325B3100-0329B3100-0326
Dual-Rail® Cover
• Sections up to 12" wide are manufactured at 12' lengths.Sections over 12" wide are manufactured at 6' lengths.Canadian orders (3m length) change seventh digit of partnumber to 5.
• All aluminum tray covers shown are made of aluminum.
• All steel covers shown are made of galvanized steel.
30 DEGREEPEAKED COVER
6 4100-0321
TrayWidth
(in)
Top RungAluminum Tray
P/N
9 4100-032212 4100-032318 4100-032424 4100-0325
4200-0321
Top RungSteel Tray
P/N
4200-03224200-03234200-03244200-0325
B4100-0321
Bottom RungAluminum Tray
P/N
B4100-0322B4100-0323B4100-0324B4100-0325
B4200-0321
Bottom RungSteel Tray
P/N
B4200-0322B4200-0323B4200-0324B4200-0325
30 4100-0329 4200-0329 B4100-0329 B4200-032936 4100-0326 4200-0326 B4100-0326 B4200-0326
30 Degree Peaked Cover
• Standard 12'-0" (3.6m) length. Canadian orders (3m length)change seventh digit of part number to 5.
• All aluminum tray covers shown are made of aluminum.
• All steel covers shown are made of galvanized steel.
120˚
Provides additional protection for cables and wiring.
Page 201201
Covers & Inserts
Solid Bottom Inserts
MONO-TRAY®
SOLID BOTTOM INSERT
6 5103-0321
TrayWidth
(in)
Top RungAluminum Tray
P/N
9 5103-032212 5103-032318 5103-032424 5103-0325
5203-0321
Top RungSteel Tray
P/N
5203-03225203-03235203-03245203-0325
B5103-0321
Bottom RungAluminum Tray
P/N
B5103-0322B5103-0323B5103-0324B5103-0325
B5203-0321
Bottom RungSteel Tray
P/N
B5203-0322B5203-0323B5203-0324B5203-0325
Mono-Tray® Solid Bottom Insert
• Standard 12'-0" (3.6m) length. Canadian orders (3m length)change seventh digit of part number to 5.
• Change 4th digit of part number to 6 for 6" (150mm) tray height.
• Change 4th digit of part number to 4 for 4" (100mm) tray height.
• All aluminum tray inserts shown are made of aluminum.
• All steel inserts shown are made of galvanized steel.
DUAL-RAIL®
SOLID BOTTOM INSERT
18 5103-0324
TrayWidth
(in)
Top RungAluminum Tray
P/N
24 5103-032530 5103-032936 5103-0326
5203-0324
Top RungSteel Tray
P/N
5203-03255203-03295203-0326
B5103-0324
Bottom RungAluminum Tray
P/N
B5103-0325B5103-0329B5103-0326
B5203-0324
Bottom RungSteel Tray
P/N
B5203-0325B5203-0329B5203-0326
Dual-Rail® Solid Bottom Insert
• Standard 12'-0" (3.6m) length. Canadian orders (3m length)change seventh digit of part number to 5.
• Change 4th digit of part number to 6 for 6" (150mm) tray height.
• Change 4th digit of part number to 4 for 4" (100mm) tray height.
• All aluminum tray inserts shown are made of aluminum.
• All steel inserts shown are made of galvanized steel.
Use with cable tray covers to create an enclosed cable tray system.
Top Rung
Bottom Rung
Top Rung
Bottom Rung
Two inserts provided for bottom rung Mono-Tray®
Three inserts provided for bottom rung Dual-Rail®
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 202202
Support & Installation Accessories
Miscellaneous Accessories
Rung Caps & Replacement Rungs
12" (304mm)Ground StrapFor use at wall penetrations or at anypoint where tray continuity is broken.2 - 7/16" dia. (11mm) mounting holes.
AluminumTray P/N
SteelTray P/N
0100-0521 0200-0521
Divider StripSelf-tapping screws provided forattachment.
End CapTerminates open end of spine. Nut, bolt,and washer provided.
AluminumTray P/N
SteelTray P/N
0100-0500 0200-0500
Rung CapsTo denote specific circuit paths or enhancetray appearance. Field install.
ReplacementRungsAdditional rungsto be used withaluminumremovable rungcable tray(pg. 65 - 69).Attachmentscrew provided.
BraidedAluminum
Divider Heightin mm
3
AluminumTray P/N
SteelTray P/N
4
6
75 0103-0440 N/A
0104-0440 N/A
0106-0440 N/A
100
150
Divider Strip
RUNG CAPS
0800-0710-BK Black Type "C" AluminumRung (STD.)& Type "B"
Type "D" Aluminum Rung
Type "E" Steel Rung (STD.)
0800-0710-GY Gray0800-0710-RD Red0800-0711-BK Black0800-0711-FO Flr Orange0800-0711-BK Black0800-0711-FO Flr Orange
P/N Color For Use With
Actual Tray Width
in mm
3
AluminumCatalog #
75 0100-0531-R
6 150 0100-0532-R
7 1/2 191 0100-0533-R
9 225 0100-0534-R
12 300 0100-0535-R
13 1/2 343 0100-0536-R
18 450 0100-0537-R
24 600 0100-0538-R
REPLACEMENT RUNGS
Page 203203
Welded Fittings
Example Tray Catalog NumberTop Rung Mono-Tray Aluminum, 3" Rung Height, 18" Radius, 90˚ Horizontal Elbow, 9" Wide
TRAY STYLE TRAY TYPE MATERIAL FITTING TYPE TRAY WIDTH
_ 1 1 0 3 2 22 3
B
L
BottomRung Tray
Light DutyTray
1
2
Mono-Tray
Dual-Rail
1
2
3
4
5
6
Aluminum
Pre-GalvanizedSteel
Hot DippedGalvanizedSteel afterFabrication
Epoxy Paint(Aluminum)
Epoxy Paint(Steel)
AnodizedAluminum
6"
9"
12"
18"
24"
36"
3"
4"
30"
150
225
300
450
600
900
75
100
750
1
2
3
4
5
6
7
8
9
in mm
30˚ IVR45˚ IVR60˚ IVR90˚ IVR30˚ OVR45˚ OVR60˚ OVR90˚ OVRVert. CrossVert. Tee IVRVert. Tee OVRCable Hanger EL30˚ Horiz. EL45˚ Horiz. EL60˚ Horiz. EL90˚ Horiz. ELHoriz. CrossHoriz. TeeHoriz. Wye L.H.Horiz. Wye R.H.
0102030405060708091011122021222324252627
Fitting Quick Selector
RADIUS
12"
18"
24"
36"
6"
30"
800
450
600
900
150
750
1
2
3
4
5
6
in mmRUNG HEIGHT
3"
4"
6"
75
100
150
3
4
6
in mm
For Top RungStandard Tray
No Letter Prefixis required
NOTE: Most elbows, tees, and directionalchanges can be achieved by utilizingstandard components and Quick Fittings.Welded fittings are designed to accommodatespecific cable radii requirements.Support documentation/details areavailable upon request.
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Page 204204
Specifications Mono-Tray®
PART 1 - GENERAL
1.10 REFERENCE STANDARDS:A. Underwriter1s Laboratories, Inc. certified No. E80034; National Electrical Code 318; NEMA class 12C (100#/ft./12 ft.) for Mono-Tray. L-Series NEMA 12A - 50#/ft./12ft..B. Canadian Standards Association No. LR 082927, Mono-Tray 3 meter sections are CSA classified 3C12 and 3D12 (179kg/m/3m). L-Series Mono-TrayCSA classified 3A2 (37kg/m/3m).C. The cable tray system components shall be certified by one of the following UL, C-UL, CSA and/or a recognized testing laboratory.
1.20 DESCRIPTION:A. Complete center hung and/or wall mounted steel or aluminum (select one) cable tray system and necessary accessories shall be provided as shown on plans. Install entire
cable tray system in accordance with all local governing codes.
1.30 SUBMITTALS:A. Submittal drawings, in the form of 8 1/2 x 11 catalog cut sheets, shall be provided for the following items: cable trays, fittings, accessories and load data.
PART 2 - PRODUCTS
2.10 MATERIALS - Steel or Aluminum (SELECT 3A or B2)A. Steel cable trays shall be ventilated ladder type construction with widths and depths as indicated on the drawings. The ladder tray shall be supported from one (1) steel
splice connector, installed in a telescoping manner, around the outer portion of the main spine members.B. Aluminum cable trays shall be ventilated ladder type construction with widths and depths as indicated on the drawings. The ladder tray shall be supported from one
(1) aluminum splice connector, installed inside the inner portion of the main spine members.
2.20 CENTER HUNG Mono-Tray - Steel or Aluminum (SELECT 3A or B2)A. Steel Mono-Tray shall be constructed of one (1) 12x32 rectangular seam welded steel tube to which .6252 square seam welded tube steel rungs are attached on _____ inch
(mm) centers. The cross rungs shall be bent up at their ends to a height of _____ inches (mm) to form a center supported, open sided, ladder type assembly. The trayshall be ______inches (mm) wide and must not have continuous side rails. As noted on drawings, rungs shall emanate at right angles from the top of the spine or bottomof the spine (select one).
B. Aluminum Mono-Tray Ladder Tray shall be constructed of one (1) 1.52x2.752 rectangular extruded aluminum tube to which 1/2" square box beam (type C standard) or3/4" x 1/2" box beam (type D) (select one) rungs are attached on _____ inch (mm) centers. The cross rungs shall be bent up at their ends to a height of _____ inches(mm) to form a dual supported, open sided, ladder type assembly. The tray must not have continuous side rails. As noted on drawings, rungs shall emanate at right anglesfrom the top of the spine or bottom of the spine (select one). L-Series Mono-Tray shall have 1/2" solid aluminum triangular (type B) rungs.
2.30 WALL RACK LADDER TRAY - Steel or Aluminum (SELECT 3A or B2)A. Steel Wall Rack tray shall be constructed of one (1) 12x32 rectangular seam welded steel tubes to which .6252 square seam welded tube steel rungs are attached on
_____ inch (mm) centers. The cross rungs shall emanate from one side of the spine and shall be bent up at their ends to a height of _____ inches (mm) to form an opensided, ladder type assembly. The tray shall be ______inches (mm) wide and must not have continuous side rails. As noted on drawings, rungs shall emanate at rightangles from the top of the spine or bottom of the spine (select one).
B. Aluminum Wall Rack tray shall be constructed of one (1) 1.52x2.752 rectangular extruded aluminum tube to which ?2 square box beam (type C standard) or 3/4" x 1/2" boxbeam (type D) rungs are attached on _____ inch (mm) centers. The cross rungs shall be emanate from one side of the spine and shall be bent up at their ends to a heightof _____ inches (mm) to an open sided, ladder type assembly. The tray must not have continuous side rails. As noted on drawings, rungs shall emanate at right angles fromthe top of the spine or bottom of the spine (select one). L-Series Wall Rack shall have 1/2" solid aluminum triangular (type B) rungs.
2.40 DOUBLE TIER WALL RACK LADDER TRAY - Aluminum OnlyA. Aluminum Wall Rack Double Tier tray shall be constructed of one (1) 1.52x2.752 rectangular extruded aluminum tube to which 1/2" square box beam (type C standard)
rungs are attached on _____ inch (mm) centers. These cross rungs shall emanate from one side (top of the spine only) and also vertically from the bottom of the spine toform two tiers of cable tray, one above the other and shall be bent up at their ends to a height of _____ inches (mm) to an open sided, ladder type assembly. The tray mustnot have continuous side rails. Tray shall be mounted by fastening the spine directly to the wall in accordance with manufacturer’s specifications.
2.50 FITTINGSA. Splice Connectors - Steel or Aluminum (select one). Sections of Mono-Tray, Wall Rack and/or Double Tier Wall Rack and all other fittings shall be joined by using one (1),
two bolt, 4 inch (102mm) long, rectangular splice connector which telescope about the spine of the tray. Splice connectors shall allow for thermal expansion/contraction ofthe tray system. The splice connectors shall be provided with a vertical hole to accept a 1/2 inch (12mm) threaded rod (furnished by others) which is used to support thetray in an overhead application. In addition, steel splice connectors shall be installed with the seam up and shall have holes to accommodate mounting configurationsassociated with horizontal and vertical pivot connectors.
B. Quick Tee and Quick Cross Connectors. Horizontal and Vertical quick connect items shall be used for all 90 degree elbows. Quick Tees and Crosses shall have factoryinstalled splice connector(s) welded to the component assembly.
C. Horizontal and Vertical Pivot Connectors - Angle tray connections to be field installed with Horizontal and Vertical pivot connectors. Fittings and shall telescope about thespine in a similar manner as the above splice connectors with top or side mounted pivot plates.
D. Tray Inserts / Tray Covers - Steel or Aluminum (select one), as well as other accessories shall be constructed of compatible material and design. Inserts and covers shall befield installed and rigidly secured by means of self tapping screws.
2.60 CONSTRUCTIONA. The Mono-Tray, Wall Rack and/or Double Tier Wall Rack rungs must pass through sections of spine and be staked in place, not screwed or welded. Each tray length shall
consist of one tubular rectangular shaped spine member. All fittings and accessories to be constructed of steel or aluminum (select one) and to be manufactured for usewith cable tray system.
2.70 SUPPORTSA. Each Mono-Tray, Wall Rack and/or Double Tier Wall Rack ladder tray section shall be supported on maximum 12 foot centers (3.6 meters) in Canada 10 foot centers (3
meters) by one .50 inch (12mm) piece of threaded rod which pass through the vertical hole in each of the splice connectors and fasten directly to each piece of spine byone .50 inch (12mm) nut and washer on both the top and bottom sides of each piece spine. When shorter spans are required, then a 5/8 inch (16 mm) diameter holeshould be drilled through the top and bottom walls of each piece of spine at support points only, and a single .50 inch (12mm) threaded rod should be inserted, througheach spine member, also using a .50 inch (12mm) nut and washer on both the top and bottom sides of the spine.
B. Wall Mounted Mono-Tray Steel or Aluminum (select one) Ladder Tray - shall utilize wall bracket of adequate widths to accommodate Mono-Tray configuration. Brackets tobe Mono-Systems, Inc. Series 0100-047_. All mounting material shall be furnished and installed by others.
2.80 OPTIONAL PAINTED FINISHESA. Optional powder coated painted finish to be applied to the outer surfaces of the cable tray and associated components. Prior to the application of the powder coat all
surfaces shall be cleaned and have an iron phosphate film applied. The color shall be __________.
PART 3 - MANUFACTURER
3.10 MANUFACTURER
A. Company specializing in manufacturing products specified in this section must have a minimum of ten years documented experience. Unless written approval is obtainedfrom the engineer 14 days prior to bid, the cable tray and fittings shall be manufactured by: Mono-Systems, Inc., 4 International Drive, Rye Brook New York 10573.(TEL) 914-934-2075 (FAX) 914-934-2190.
Page 205205
TR
OU
GH
TR
AY
CE
NT
ER
SP
INE
MO
NO
-R
AC
KM
ON
O-
ME
SH
PO
WE
R-
TR
AY
Specifications Dual-Rail®
PART 1 - GENERAL
1.10 REFERENCE STANDARDS:A. Underwriter's Laboratories, Inc. certified No. E80034; National Electrical Code 318; NEMA class 12C (100#/ft./12 ft.).B. Canadian Standards Association No. LR 082927, Dual-Rail 3 meter sections are CSA classified "E" (299kg/m/3m).C. The cable tray system components shall be certified by one of the following UL, C-UL, CSA and/or a recognized testing laboratory.
1.20 DESCRIPTION:A. Complete assembly of steel or aluminum (select one) cable tray system and necessary accessories shall be provided as shown on plans. Install entire
cable tray system in accordance with all local governing codes.
1.30 SUBMITTALS:A. Submittal drawings, in the form of 8 " x 11" catalog cut sheets, shall be provided for the following items: cable trays, fittings, accessories and load data.
PART 2 - PRODUCTS
2.10 MATERIALS (SELECT "A or B")A. Steel Dual-Rail shall be ventilated ladder type construction with widths and depths as indicated on the drawings. The ladder tray shall be supported from two (2) steel splice
connectors, installed in a telescoping manner, around the outer portion of the main spine members.B. Aluminum Dual-Rail shall be ventilated ladder type construction with widths and depths as indicated on the drawings. The ladder tray shall be supported from two (2) aluminum
splice connectors, installed inside the inner portion of the main spine members.
2.20 Dual-Rail® LADDER TRAY - Steel or Aluminum (SELECT "A or B")A. Steel Dual-Rail Ladder Tray shall be constructed of two (2) 1"x3" rectangular seam welded steel tubes to which .625" square seam welded tube steel rungs are attached
on _____ inch (mm) centers. The cross rungs shall be bent up at their ends to a height of _____ inches (mm) to form a dual supported, open sided, ladder type assembly. Thetray must not have continuous side rails. As noted on drawings, rungs shall emanate at right angles from the top of the spine or bottom of the spine (select one).
B. Aluminum Dual-Rail Ladder Tray shall be constructed of two (2) 1.5""x2.75" rectangular extruded aluminum tubes to which " square box beam (type C standard) or " x " box beam(type D) (select one) rungs are attached on _____ inch (mm) centers. The cross rungs shall be bent up at their ends to a height of _____ inches (mm) to form a dual supported,open sided, ladder type assembly. The tray must not have continuous side rails. As noted on drawings, rungs shall emanate at right angles from the top of the spine or bottom ofthe spine (select one).
2.30 FITTINGSA. Splice Connectors - Steel or Aluminum (select one). Sections of Dual-Rail tray and all other fittings shall be joined by using two (2), two bolt, 4 inch (102mm) long, rectangular splice
connectors which telescope about the spine of the tray. Splice connectors shall allow for thermal expansion/contraction of the tray system. The splice connectors shall be providedwith a vertical hole to accept a 1/2 inch (12mm) threaded rod (furnished by others) which is used to support the tray in an overhead application. In addition, steel splice connectorsshall be installed with the welded seam up and shall have holes to accommodate mounting configurations associated with horizontal and vertical pivot connectors.
B. Quick Tee - Steel or Aluminum (select one), Horizontal and Vertical quick connect items shall be used for all 90 degree elbows, tees and crosses by clamping to the spine(s).C. Horizontal and Vertical Pivot Connectors - Steel or Aluminum (select one), shall be used for angles of 90 degrees to 30 degrees and fasten into the spine in a similar manner as the
above splice connectors with top or side mounted pivot plates.D. Tray Inserts / Tray Covers - Steel or Aluminum (select one), as well as other accessories shall be constructed of compatible material and design. Inserts and covers shall be field
installed and rigidly secured by means of self tapping screws.
2.40 CONSTRUCTIONA. The Dual-Rail rungs must pass through both sections of spine and be staked in place, not screwed or welded. Each tray length shall consist of two parallel spine members, each
being a tubular rectangular shape. All fittings and accessories to be constructed of steel or aluminum (select one) and to be manufactured for use with cable tray system.
2.50 SUPPORTSA. Each Dual-Rail Steel or Aluminum (select one). Ladder Tray section shall be supported on maximum 12 foot centers (3.6 meters) in Canada 10 foot centers (3 meters) by two .50
inch (12mm) pieces of threaded rod which pass through the vertical hole in each of the splice connectors and fasten directly to each piece of spine by one .50 inch (12mm) nut andwasher on both the top and bottom sides of each piece spine. When shorter spans are needed, then a 5/8 inch (16 mm) diameter hole should be drilled through the top and bottomwalls of each piece of spine at support points only, and a single .50 inch (12mm) threaded rod should be inserted, through each spine member, also using a .50 inch (12mm) nut andwasher on both the top and bottom sides of each piece of spine. All mounting material shall be furnished and installed by others.
2.60 OPTIONAL PAINTED FINISHESA. Optional powder coated painted finish to be applied to the outer surfaces of the cable tray and associated components. Prior to the application of the powder coat all surfaces shall
be cleaned and have an iron phosphate film applied. The color shall be __________.
PART 3 - MANUFACTURER
3.10 MANUFACTURERA. Company specializing in manufacturing products specified in this section must have a minimum of ten years documented experience. The cable tray and fittings shall be
manufactured by: Mono-Systems, Inc., 4 International Drive, Rye Brook New York 10573. (TEL) 914-934-2075 (FAX) 914-934-2190.