Mónica&Marina car
-
Upload
technoteacher3 -
Category
Engineering
-
view
651 -
download
0
Transcript of Mónica&Marina car
IES Parque de Lisboa
Remote controlled car
Members:
Marina Arshava
Mónica Dies
1.1 Controller: Tools
Photo Name Use in the project
Pencil Drawing the form of the controller.
Scissors Cuting pieces of cardboard of the controller.
Glue gun Glueing together different parts of the controller
Saw Cuting pieces of wood of the controller.
Sand paper Making soft the pieces of wood.
Gimlet Making holes in piecesof cardboard and wood.
1.2 Controller: Components
Photo Name Nº of parts Dimensions
Base(Round wooden part)
1 d = 15cm
Base(Round cardboard part)
2 d = 15cm
Battery 2 7cmx5cmx1cm
Tinplate 2 7cmx0.5cm
Wooden rectangle 1 4cmx3cmx1cm
Nail 3 0.5cm
Wires 3 5 cm
Tack 2
1.3 Controller: Steps
Step Photo Explanation
1 Drawing the base of the controller. It is round as the recicled piece of wood that we found.
2 Cuting pieces of cardboard of the controller
3 Cutting the rests of thewooden part of the base with a saw. It hadwooden squares glued on it from other project.
4Glueing together the 3parts of the controller: 1 cardboard pieces with 1 wooden piece in the middle.
5We cut 2 pieces of wood to make the tinplates.
6 We covered the 2 wooden pieces with aluminium foil to conduct electricity,
7We did a hole on a small rectangular piece of wood
8We did the same with the base.
9We glued the tinplatesto the wood and joinedit to the base with a small piece of iron so that way it could rotate.Also we put 3 nails between the tinplates.
10Finally we glued the battery on the base and connected it to thetinplates with wires and tacks
1.1 Car: Tools
Photo Name Use in the project
Pencil Drawing the form of the car
Scissors Cuting pieces of cardboard (the base, the body of the car)
Glue gun Glueing together different parts of the car.
Saw Cuting pieces of wood (the pieces of wood that hold the axels, thepencils wich work as axels)
Sand paper Making soft the pieces of wood.
File Shaping the form of the pieces of wood that hold the axels.
Adhesive tape To glue the wires to the car and between them.
Gimlet Make holes in the wheels for the axel
1.2 Car: Components
Photo Name Nº of parts Dimensions
Base 1 17cmx11cm
Axel (pencil) 2 15cm
Wheel (cap) 4 d=5cm
Wooden holder 4 2cmx2cmx1cm
Motor 1 2cmx1cmx1cm
Bulb 1 1.5cm
Wires 2 60cm
Elastic band 1 5com
Body 1 18cmx10cmx4cm
1.3 Car: Steps
Step Photo Explanation
1 Drawing the base of the car. It was supposed to be rectangular but because of a problem with one axel it finished with other shape.
2 We cut 2 pieces of carboard for the base to be more rigid and resistant.
3 We did holes on the 4 cups fot thr axels.
4We inserted the axels on the wheels and glued them to be moreresistant.
5We shaped 4 pieces of wood in order to hold the axels.
6We glued together all the parts we had already.
7We connected the wires to the motor andglued it to the car withadhesive tap.
8We glued the motor tothe car and connected it with a wheel through an elastic band.
9We joined the wires with adhesive tap.
10We joined the wires ofthe bulb to the wires of the motor so when we switch them on, both work.
11This way both, bulb and motor work.
12 Finally, we did the body of the car and glued it to the base.
OUR CAR IS READY TORACE!!