MOMENTUM! Momentum Impulse Conservation of Momentum.

47
MOMENTUM! Momentum Impulse Conservation of Momentum

Transcript of MOMENTUM! Momentum Impulse Conservation of Momentum.

Page 1: MOMENTUM! Momentum Impulse Conservation of Momentum.

MOMENTUM!

Momentum

Impulse

Conservation of Momentum

Page 2: MOMENTUM! Momentum Impulse Conservation of Momentum.

2

ObjectivesI will learn relationships of variables expressed in the momentum equations.

I will describe the relationships between momentum and vectors.

I can solve momentum problems in one dimension for elastic and inelastic collisions.

I can solve problems for the conservation of momentum using vectors and trigonometry. 2

Page 3: MOMENTUM! Momentum Impulse Conservation of Momentum.
Page 4: MOMENTUM! Momentum Impulse Conservation of Momentum.

Momentum Facts• p = m v

• Momentum is a vector quantity!

• Velocity and momentum vectors point in the same direction.

• SI unit for momentum: kg · m /s (no special name).

• Momentum is a conserved quantity (this will be proven later).

• A net force is required to change a body’s momentum.

• Momentum is directly proportional to both mass and speed.

• Something big and slow could have the same momentum as something small and fast.

Page 5: MOMENTUM! Momentum Impulse Conservation of Momentum.

Momentum Examples

10 kg 3 m /s

10 kg30 kg · m /s

Note: The momentum vector does not have to be drawn 10 times longer than the velocity vector, since only vectors of the same quantity can be compared in this way.

5 g

9 km /s

p = 45 kg · m /s at 26º N of E

26º

Page 6: MOMENTUM! Momentum Impulse Conservation of Momentum.

Equivalent Momenta

Bus: m = 9000 kg; v = 16 m /s p = 1.44 ·105 kg · m /s

Train: m = 3.6 ·104 kg; v = 4 m /s p = 1.44 ·105 kg · m /s

Car: m = 1800 kg; v = 80 m /s p = 1.44 ·105 kg · m /s

continued on next slide

Page 7: MOMENTUM! Momentum Impulse Conservation of Momentum.

Equivalent Momenta (cont.)

The train, bus, and car all have different masses and speeds, but their momenta are the same in magnitude.

The difficulty in bringing each vehicle to rest--in terms of a combination of the force and time required--would be the same, since they each have the same momentum.

Page 8: MOMENTUM! Momentum Impulse Conservation of Momentum.

88

Page 9: MOMENTUM! Momentum Impulse Conservation of Momentum.

Impulse Defined

Impulse is defined as the product force acting on an object and the time during which the force acts. The symbol for impulse is I. So, by definition:

I = F t

Example: A 50 N force is applied to a 100 kg boulder for 3 s. The impulse of this force is I = (50 N) (3 s) = 150 N · s.

Note that we didn’t need to know the mass of the object in the above example.

Page 10: MOMENTUM! Momentum Impulse Conservation of Momentum.

Impulse UnitsI = F t shows why the SI unit for impulse is the Newton · second. There is no special name for this unit, but it is equivalent to a kg · m /s.

proof: 1 N · s = 1 (kg · m /s2) (s) = 1 kg · m /s{

Fnet = m a shows this is equivalent to a newton.

Therefore, impulse and momentum have the same units, which leads to a useful theorem.

Page 11: MOMENTUM! Momentum Impulse Conservation of Momentum.

Impulse - Momentum Theorem

The impulse due to all forces acting on an object (the net force) is equal to the change in

momentum of the object:

Fnet t = Δ p

We know the units on both sides of the equation are the same (last slide), but let’s prove the

theorem formally:

Fnet t = m a t = m (Δ v /

t) t = m Δ v = Δ p

Page 12: MOMENTUM! Momentum Impulse Conservation of Momentum.

1212

Page 13: MOMENTUM! Momentum Impulse Conservation of Momentum.

1313

Page 14: MOMENTUM! Momentum Impulse Conservation of Momentum.

1414

Page 15: MOMENTUM! Momentum Impulse Conservation of Momentum.

1515

QuickTime™ and aYUV420 codec decompressor

are needed to see this picture.

Page 16: MOMENTUM! Momentum Impulse Conservation of Momentum.

Proof of Conservation of MomentumThe proof is based on Newton’s 3rd Law. Whenever two objects collide (or exert forces on each other from a distance), the forces involved are an action-reaction pair, equal in strength, opposite in direction. This means the net force on the system (the two objects together) is zero, since these forces cancel out.

M mFF

force on m due to M

force on M due to m

For each object, F = (mass) (a) = (mass) (Δv / t ) = (mass Δv) / t = Δp / t. Since the force applied and the contact time is the same for each mass, they each undergo the same change in momentum, but in opposite directions. The result is that even though the momenta of the individual objects changes, Δp for the system is zero. The momentum that one mass gains, the other loses. Hence, the momentum of the system before equals the momentum of the system after.

Page 17: MOMENTUM! Momentum Impulse Conservation of Momentum.

1717

QuickTime™ and alibx264 decompressor

are needed to see this picture.

Page 18: MOMENTUM! Momentum Impulse Conservation of Momentum.

1818

Page 19: MOMENTUM! Momentum Impulse Conservation of Momentum.

Conservation of Momentum in 2-D

m1m2

v1

v2

m1 m2

vavb

θ1θ2

θaθ b

To handle a collision in 2-D, we conserve momentum in each dimension separately. Choosing down & right as positive:

before: px = m1 v1 cosθ1 - m2 v2 cosθ2

py = m1 v1 sinθ1 + m2 v2 sinθ2

after: px = -m1 va cosθa + m2 vb cosθ b

py = m1 va sinθa + m2 vb sinθ b

Conservation of momentum equations:

m1 v1 cosθ1 - m2 v2 cosθ2 = -m1 va cosθa + m2 vb cosθ b

m1 v1 sinθ1 + m2 v2 sin θ2 = m1 va sinθa + m2 vb sinθ b

Page 20: MOMENTUM! Momentum Impulse Conservation of Momentum.

Conserving Momentum w/ Vectors

m1m2

p1

p 2

m1 m2

p a p b

θ1θ2

θaθ b

BEFORE

AFTER

This diagram shows momentum vectors, which are parallel to their respective velocity vectors. Note p1 + p 2

= p a + p b and p before = p after as conservation of momentum demands.

p1

p 2

p before

p a

p b

p after

Page 21: MOMENTUM! Momentum Impulse Conservation of Momentum.

21

QuickTime™ and aYUV420 codec decompressor

are needed to see this picture.

Page 22: MOMENTUM! Momentum Impulse Conservation of Momentum.

Exploding Bomb

A c m e

before

after

A

c

m

eA bomb, which was originally at rest, explodes and shrapnel flies every which way, each piece with a different mass and speed. The momentum vectors are shown in the after picture.

continued on next slide

Page 23: MOMENTUM! Momentum Impulse Conservation of Momentum.

Exploding Bomb (cont.)

Since the momentum of the bomb was zero before the explosion, it must be zero after it as well. Each piece does have momentum, but the total momentum of the exploded bomb must be zero afterwards. This means that it must be possible to place the momentum vectors tip to tail and form a closed polygon, which means the vector sum is zero.

If the original momentum of the bomb were not zero, these vectors would add up to the original momentum vector.

Page 24: MOMENTUM! Momentum Impulse Conservation of Momentum.

Imagine a car hitting a wall and coming to rest. The force on the car due to the wall is large (big F ), but that force only acts for a small amount of time (little t ). Now imagine the same car moving at the same speed but this time hitting a giant haystack and coming to rest. The force on the car is much smaller now (little F ), but it acts for a much longer time (big t ). In each case the impulse involved is the same since the change in momentum of the car is the same. Any net force, no matter how small, can bring an object to rest if it has enough time. A pole vaulter can fall from a great height without getting hurt because the mat applies a smaller force over a longer period of time than the ground alone would.

Stopping Time

F t = F t

Page 25: MOMENTUM! Momentum Impulse Conservation of Momentum.

Impulse - Momentum Example

A 1.3 kg ball is coming straight at a 75 kg soccer player at 13 m/s who kicks it in the exact opposite direction at 22 m/s with an average force of 1200 N. How long are his foot and the ball in contact?

answer: We’ll use Fnet t = Δ p. Since the ball changes direction, Δ p = m Δ v = m (vf - v0) = 1.3 [22 - (-13)] = (1.3 kg) (35 m/s) = 45.5 kg · m /s. Thus, t = 45.5 / 1200 = 0.0379 s, which is just under 40 ms.

During this contact time the ball compresses substantially and then decompresses. This happens too quickly for us to see, though. This compression occurs in many cases, such as hitting a baseball or golf ball.

Page 26: MOMENTUM! Momentum Impulse Conservation of Momentum.

Fnet vs. t graphFnet (N)

t (s)6

A variable strength net force acts on an object in the positive direction for 6 s, thereafter in the opposite direction. Since impulse is Fnet t, the area under the curve is equal to the impulse, which is the change in momentum. The net change in momentum is the area above the curve minus the area below the curve. This is just like a v vs. t graph, in which net displacement is given area under the curve.

Net area = Δ p

Page 27: MOMENTUM! Momentum Impulse Conservation of Momentum.

Conservation of Momentum in 1-DWhenever two objects collide (or when they exert forces on each other without colliding, such as gravity) momentum of the system (both objects together) is conserved. This mean the total momentum of the objects is the same before and after the collision.

before: p = m1 v1 - m2 v2

after: p = - m1 va + m2 vb

m1 m2

v1v2

(Choosing right as the +

direction, m2 has - momentum.)

m1 m2

va vb

m1 v1 - m2 v2 = - m1 va + m2 vb

Page 28: MOMENTUM! Momentum Impulse Conservation of Momentum.

Directions after a collisionOn the last slide the boxes were drawn going in the opposite direction after colliding. This isn’t always the case. For example, when a bat hits a ball, the ball changes direction, but the bat doesn’t. It doesn’t really matter, though, which way we draw the velocity vectors in “after” picture. If we solved the conservation of momentum equation (red box) for vb

and got a negative answer, it would mean that m2 was still moving to the left after the collision. As long as we interpret our answers correctly, it matters not how the velocity vectors are drawn.

m1 v1 - m2 v2 = - m1 va + m2 vb

m1 m2

v1v2

m1 m2

va vb

Page 29: MOMENTUM! Momentum Impulse Conservation of Momentum.

Sample Problem 1

7 kg

v = 0700 m/s

A rifle fires a bullet into a giant slab of butter on a frictionless surface. The bullet penetrates the butter, but while passing through it, the bullet pushes the butter to the left, and the butter pushes the bullet just as hard to the right, slowing the bullet down. If the butter skids off at 4 cm/s after the bullet passes through it, what is the final speed of the bullet?(The mass of the rifle matters not.)

35 g

7 kgv = ?

35 g

4 cm/s

continued on next slide

Page 30: MOMENTUM! Momentum Impulse Conservation of Momentum.

Sample Problem 1 (cont.)

7 kg

v = 0

700 m/s

35 g

7 kgv = ?

35 g

4 cm/s

p before = 7 (0) + (0.035) (700)

= 24.5 kg · m /s

Let’s choose left to be the + direction & use conservation of momentum, converting all units to meters and kilograms.

p after = 7 (0.04) + 0.035 v

= 0.28 + 0.035 v

p before = p after 24.5 = 0.28 + 0.035 v v = 692 m/s

v came out positive. This means we chose the correct direction of the bullet in the “after” picture.

Page 31: MOMENTUM! Momentum Impulse Conservation of Momentum.

Sample Problem 2

7 kg

v = 0

700 m/s

35 g

Same as the last problem except this time it’s a block of wood rather than butter, and the bullet does not pass all the way through it. How fast do they move together after impact?

v7. 035 kg

(0.035) (700) = 7.035 v v = 3.48 m/s

Note: Once again we’re assuming a frictionless surface, otherwise there would be a frictional force on the wood in addition to that of the bullet, and the “system” would have to include the table as well.

Page 32: MOMENTUM! Momentum Impulse Conservation of Momentum.

Conservation of Momentum applies only in the absence of external forces!

In the first two sample problems, we dealt with a frictionless surface. We couldn’t simply conserve momentum if friction had been present because, as the proof on the last slide shows, there would be another force (friction) in addition to the contact forces. Friction wouldn’t cancel out, and it would be a net force on the system.

The only way to conserve momentum with an external force like friction is to make it internal by including the tabletop, floor, or the entire Earth as part of the system. For example, if a rubber ball hits a brick wall, p for the ball is not conserved, neither is p for the ball-wall system, since the wall is connected to the ground and subject to force by it. However, p for the ball-Earth system is conserved!

Page 33: MOMENTUM! Momentum Impulse Conservation of Momentum.

Sample Problem 3

EarthM

apple

An apple is originally at rest and then dropped. After falling a short time, it’s moving pretty fast, say at a speed V. Obviously, momentum is not conserved for the apple, since it didn’t have any at first. How can this be?

m

F

F

answer: Gravity is an external force on the apple, so momentum for it alone is not conserved. To make gravity “internal,” we must define a system that includes the other object responsible for the gravitational force--Earth. The net force on the apple-Earth system is zero, and momentum is conserved for it. During the fall the Earth attains a very small speed v. So, by conservation of momentum:

V

v

m V = M v

Page 34: MOMENTUM! Momentum Impulse Conservation of Momentum.

Sample Problem 4

before

after

3 kg 15 kg10 m/s 6 m/s

3 kg 15 kg4.5 m/s v

A crate of raspberry donut filling collides with a tub of lime Kool Aid on a frictionless surface. Which way on how fast does the Kool Aid rebound? answer: Let’s draw v to the right in the after picture.

3 (10) - 6 (15) = -3 (4.5) + 15 v v = -3.1 m/sSince v came out negative, we guessed wrong in drawing v to the right, but that’s OK as long as we interpret our answer correctly. After the collision the lime Kool Aid is moving 3.1 m/s to the left.

Page 35: MOMENTUM! Momentum Impulse Conservation of Momentum.

2-D Sample Problem

0.3 kg

34 m/s40

152 gA mean, old dart strikes an innocent mango that was just passing by minding its own business. Which way and how fast do they move off together?

before

after

5 m/s

452 g

θ

v

152 (34) sin 40 = 452 v sinθ

152 (34) cos 40 - 300 (5) = 452 v cosθ

Working in grams and taking left & down as + :

Dividing equations :

1.35097 = tanθ

θ = 53.4908Substituting into either of the first two equations : v = 9.14 m/s

Page 36: MOMENTUM! Momentum Impulse Conservation of Momentum.

4132.9736

Alternate Solution

5168

40

1500

β

p

Shown are momentum vectors (in g⋅ m/s). The black vector is the total momentum before the collision. Because of conservation of momentum, it is also the total momentum after the collisions. We can use trig to find its magnitude and direction.

Law of Sines :

40

sin β1500

Law of Cosines : p2 = 5168 2 + 1500

2 - 2 ⋅ 5168 ⋅ 1500 cos 40

p = 4132.9736 g⋅ m/s

Dividing by total mass : v = (4132.9736 g⋅ m/s) / (452 g) = 9.14 m/s

=sin 40

β = 13.4908

Angle w/ resp. to horiz. = 40 + 13. 4908 ≈ 53.49

Page 37: MOMENTUM! Momentum Impulse Conservation of Momentum.

Comments on Alternate Method

• Note that the alternate method gave us the exact same solution.

• This method can only be used when two objects collide and stick, or when one object breaks into two. Otherwise, we’d be dealing with a polygon with more sides than a triangle.

• In using the Law of Sines (last step), the angle involved (ß) is the angle inside the triangle. A little geometry gives us the angle with respect to the horizontal.

Page 38: MOMENTUM! Momentum Impulse Conservation of Momentum.

Angular Momentum

r

v

m

Angular momentum depends on linear momentum and the distance from a particular point. It is a vector quantity with symbol L. If r and

v are ⊥ then the magnitude of angular momentum w/ resp. to point Q is given by L = r p = m v r. In this case L points out of the page. If the mass were moving in the opposite direction, L would point into the page.

The SI unit for angular momentum is the kg ⋅ m2 / s. (It has no special name.) Angular momentum is a conserved quantity. A torque is needed to change L, just a force is needed to change p. Anything spinning has angular has angular momentum. The more it has, the harder it is to stop it from spinning.

Q

Page 39: MOMENTUM! Momentum Impulse Conservation of Momentum.

Angular Momentum: General Definition

r

v

m

If r and v are not ⊥ then the angle between these two vectors must be taken into account. The general definition of angular momentum is given by a vector cross product: L = r p

This formula works regardless of the angle. As you know from our study of cross products, the magnitude of the angular momentum of m relative to point Q is: L = r p sinφ = m v r. In this case, by the right-hand rule, L points out of the page. If the mass were moving in the opposite direction, L would point into the page.

Q

φ

Page 40: MOMENTUM! Momentum Impulse Conservation of Momentum.

Moment of InertiaAny moving body has inertia. (It wants to keep moving at constant v.) The more inertia a body has, the harder it is to change its linear motion. Rotating bodies possess a rotational inertial called the moment of inertial, I. The more rotational inertia a body has, the harder it is change its rotation. For a single point-like mass w/ respect to a given point Q, I = m r

2.

I = m r

2

mr

For a system, I = the sum of each mass times its respective distance from the point of interest.

r2

m2

r1

m1

I = Σ mi ri

2

= m1 r12 + m2

r22

Q

Q

Page 41: MOMENTUM! Momentum Impulse Conservation of Momentum.

Moment of Inertia ExampleTwo merry-go-rounds have the same mass and are spinning with the same angular velocity. One is solid wood (a disc), and the other is a metal ring. Which has a bigger moment of inertia relative to its center of mass?

ω ω

mm

r r

answer: I is independent of the angular speed. Since their masses and radii are the same, the ring has a greater moment of inertia. This is because more of its mass is farther from the axis of rotation. Since I is bigger for the ring, it would more difficult to increase or decrease its angular speed.

Page 42: MOMENTUM! Momentum Impulse Conservation of Momentum.

Angular AccelerationAs you know, acceleration is when an object speeds up, slows down, or changes directions. Angular acceleration occurs when a spinning object spins faster or slower. Its symbol is α, and it’s defined as:

α = Δ ω / tNote how this is very similar to a = Δ v / t for linear acceleration.Ex: If a wind turbine spinning at 21 rpm speeds up to 30 rpm over 10 s due to a gust of wind, its average angular acceleration is 9 rpm / 10 s. This means every second it’s spinning 9 revolutions per minute faster than the second before. Let’s convert the units:

9 rpm10 s =

9 rev / min 10 s =

9 rev

min ⋅ 10 s = 9 ⋅ (2 π rad) (60 s) ⋅ 10 s = 0.094 rad / s2

Since a radian is really dimensionless (a length divided by a length), the SI unit for angular acceleration is the “per second squared” (s-2).

Page 43: MOMENTUM! Momentum Impulse Conservation of Momentum.

Torque & Angular Acceleration

Newton’s 2nd Law, as you know, is Fnet = m a

The 2nd Law has a rotational analog: τ net = I α

A force is required for a body to undergo acceleration. A “turning force” (a torque) is required for a body to undergo

angular acceleration.

The bigger a body’s mass, the more force is required to accelerate it. Similarly, the bigger a body’s rotational inertia,

the more torque is required to accelerate it angularly.

Both m and I are measures of a body’s inertia (resistance to change in motion).

Page 44: MOMENTUM! Momentum Impulse Conservation of Momentum.

Linear Momentum & Angular Momentum

If a net force acts on an object, it must accelerate, which means its momentum must change. Similarly, if a net torque acts on a body, it undergoes angular acceleration, which means its angular momentum changes. Recall, angular momentum’s magnitude is given by

L = m v r

r

vm

So, if a net torque is applied, angular velocity must change, which changes angular momentum.

proof: τ net = r Fnet = r m a

= r m Δ v / t = Δ L / t

So net torque is the rate of change of angular momentum, just as net force is the rate of change of linear momentum. continued on next

slide

(if v and r are perpendicular)

Page 45: MOMENTUM! Momentum Impulse Conservation of Momentum.

Linear & Angular Momentum (cont.)

Here is yet another pair of similar equations, one linear, one rotational. From the formula v = r ω, we get

L = m v r = m r (r ω) = m r 2 ω = I ω

This is very much like p = m v, and this is one reason I is defined the way it is.

In terms of magnitudes, linear momentum is inertia times speed, and angular momentum is rotational inertia times

angular speed.

L = I ωp = m v

Page 46: MOMENTUM! Momentum Impulse Conservation of Momentum.

Spinning Ice SkaterWhy does a spinning ice skater speed up when she pulls her arms in?

Suppose Mr. Stickman is sitting on a stool that swivels holding a pair of dumbbells. His axis of rotation is vertical. With the weights far from that axis, his moment of inertia is large. When he pulls his arms in as

he’s spinning, the weights are closer to the axis, so his moment of inertia gets much smaller. Since L = I ω and L is conserved, the product of I and ω is a constant. So, when he pulls his arms in, I goes down, ω goes up, and he starts spinning much faster.

I ω = L = I ω

Page 47: MOMENTUM! Momentum Impulse Conservation of Momentum.

Comparison: Linear & Angular Momentum

Linear Momentum, p

• Tendency for a mass to continue moving in a straight line.

• Parallel to v.

• A conserved, vector quantity.

• Magnitude is inertia (mass) times speed.

• Net force required to change it.

• The greater the mass, the greater the force needed to change momentum.

Angular Momentum, L

• Tendency for a mass to continue rotating.

• Perpendicular to both v and r.

• A conserved, vector quantity.

• Magnitude is rotational inertia times angular speed.

• Net torque required to change it.

• The greater the moment of inertia, the greater the torque needed to change angular momentum.