MOLDING & MISC. CRESTWOODCATALOG · 2021. 2. 5. · Molding Extension (ME) to align with the curved...

MOLDING & MISC. CRESTWOODCATALOG

26AUGUST2019© Dura Supreme Cabinetry 10-i

Molding Index

Base Shoe 10-10Bead Board Molding 10-11Bead Molding 10-9Beaded Cove Molding 10-5Brackets 10-27Bunfoot 10-17Coat Hook (Extra/Loose) 10-24Columns 10-18aCorbels - Traditional 10-29Corbels - Transitional 10-28Corner Moldings 10-9Cottage Bead Molding 10-11Cottage Bead Spacer 10-18Countertop Support 10-27Cove Molding 10-4Craftsman Molding 10-3Crown Molding 10-2Decorative Columns 10-18bDecorative Toe Loose 10-12Dish Storage Drawer Kit (Extra/Loose) 10-25Door Only (Extra/Loose) 10-20Drawer Box (Extra/Loose) 10-22Drawer Front Only (Extra/Loose) 10-21Drawer or Roll-Out Guide (Extra/Loose) 10-22Floating Shelf 10-23Furniture Base Molding 10-10

Heat Shield 10-24Hinges 10-21Light Shield Molding 10-8Mini Molding Corbels 10-27Mirror Frame Molding 10-11Molding Extension 10-5Panel Moldings 10-11Pilasters 10-17Roll-Out Shelf Kits 10-26Shelves 10-22Shiplap Molding 10-11Solid Stock 10-18dSpecialty Moldings 10-7Starter Molding 10-6Toe Board Molding 10-10Touch-Up Kits 10-24Touch-Up Materials (Stain, Accent, Aerosol) 10-24Tray Divider Base Kit 10-25Trim Molding 10-9Turned Posts 10-15Valances 10-12Veneer Ceiling/Light Valance 10-6aWood Tops 10-19


26AUGUST2019 © Dura Supreme Cabinetry10-ii


12JULY2021© Dura Supreme Cabinetry 10-1

Moldings - General Information

1. All moldings are available in 8’ lengths unless otherwise specifi ed. Some Crown moldings (in Maple, Paintable and Cherry) are available in 8’ and 10’ lengths. Please note, 10’ lengths must ship via Dura Truck (10’ lengths are too long for UPS® or FedEx® shipments). To order 10’ moldings, verify availability (per molding pattern) and specify code with 10 after it - i.e. MCRM10. Dura Supreme will guarantee molding lengths good up to 7-1/2 feet or 9-1/2 feet to be free from “end defects”.

2. All moldings are priced per piece.

3. Some moldings are available in “curves” to match inside and outside curved cabinets.

4. All moldings have horizontal grain.

5. To avoid oversized shipping charges, when 8’ moldings are shipped via UPS, they will be reduced in size to 93”.

Code Explanation for Straight and Curved Moldings

Example: Medium Crown Molding - MCRM

Straight Molding

ACode

MCRMMCRM10

Inside Curved Molding

B Code

MCRM-B

Outside Curved Molding

CCode

MCRM-C

Descriptive Chart Shown with Each Molding Type

Details for Ordering and Installation of Curved Moldings

1 2 3Species: A C H M O P Q RH ME: Applications: A B C

Identifi es molding species availability.

A = Knotty Alder O = Oak

C = Cherry (Plus Premium Upcharge) P = Paintable*

H = Hickory

M = Maple (Plus Premium Upcharge) Q = Quarter-Sawn White Oak (Plus Premium Upcharge)

RH = Rustic Hickory

1. When ordering curved moldings, add the suffi x “B” or “C” to the appropriate molding code.

2. When installing curved moldings, most straight pieces of molding will require the use of the Molding Extension (ME) to align with the curved molding. See individual molding profi les for specifi c information.

ME = Can be used with optional Molding Extension (ME) option. (Yes or No)

Applications = Indicates straight (A), inside (B), or outside (C) curved molding availability.

1

2

3

Straight Molding with Molding Extension

Curved MoldingDoor

* Paintable moldings may be supplied in HDF or Maple, depending on the profi le and most appropriate material. For best installation of HDF moldings, a 23-guage headless pin nail is recommended


12JULY2021 © Dura Supreme Cabinetry10-2

Species:A C H M O P Q

ME:YES

Applications: A

80000 - Mini Crown Molding - XSCRM

Cat. No. PriceXSCRM 119XSCRM10 161 Cat. No. Price

LCRM 213LCRM10 334

Cat. No. PriceXLCRM 266XLCRM10 399

80050 - Small Crown Molding - SMCRM

80100 - Medium Crown Molding - MCRM

NOTE: Curved SMCRM is manufactured with Molding Extension (ME) as one piece. Straight SMCRM must be ordered with ME when used with curved SMCRM.

NOTE: Curved MCRM is manufactured with Molding Extension (ME) as one piece. Straight MCRM must be ordered with ME when used with curved MCRM.

NOTE: SMCRM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: Curved SMCRM is not available in Hickory.

NOTE: MCRM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: XSCRM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: LCRM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: XLCRM10 is available in Cherry, Paintable and Maple ONLY.

Cat. No. PriceSMCRM 147SMCRM10 201SMCRMB 616SMCRMC 707

Cat. No. PriceMCRM 191MCRM10 262MCRMB 616MCRMC 707

NOTE: Curved MCRM is not available in Hickory or Rustic Hickory.

80150 - Large Crown Molding - LCRM

80160 - Extra Large Crown Molding - XLCRM

80200 - Flex Crown Molding - FLXCRM

Cat. No. PriceFLXCRM 227FLXCRM10 333

NOTE: FLXCRM10 is available in Cherry, Paintable and Maple ONLY.

Species:A C H M O P

ME:YES

Applications: A CB

Species:A C H M O P RH

ME:YES

Applications: A CB

Species:A C H M O P RH

ME:YES

Applications: A

Species:A C M P

ME:YES

Applications: A

Species:C M O P

ME:YES

Applications: A


26AUGUST2019© Dura Supreme Cabinetry 10-3

80250 - Small Craftsman Crown Molding - SCCM

Cat. No. PriceSCCM 133SCCM10 159

NOTE: SCCM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: MCCM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: LCCM10 is available in Cherry, Paintable and Maple ONLY.

80300 - Medium Craftsman Crown Molding - MCCM

80310 - Large Craftsman Crown Molding - LCCM

Cat. No. PriceMCCM 173MCCM10 247

Cat. No. PriceLCCM 213LCCM10 334


ME:YES

Applications:


ME:YES

Applications:

Species:A C M O P Q

ME:YES

Applications:

A

A

A


26AUGUST2019 © Dura Supreme Cabinetry10-4

80350 - Mini Cove Molding - XSCVE

Cat. No. PriceXSCVE 119XSCVE10 161XSCVEB 616XSCVEC 707

NOTE: Curved XSCVE is manufactured with Molding Extension (ME) as one piece. Straight XSCVE must be ordered with ME when used with curved XSCVE.

NOTE: XSCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: LCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: XLCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: MCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: Curved XSCVE is not available in Hickory.

80400 - Medium Cove Molding - MCVE

Cat. No. PriceMCVE 191MCVE10 262

Cat. No. PriceXLCVE 266XLCVE10 399

Cat. No. PriceLCVE 213LCVE10 334

80410 - Large Cove Molding - LCVE

80420 - Extra Large Cove Molding - XLCVE


ME:YES

Applications: A CB


ME:YES

Applications: A

Species:A C H M O P Q RH

ME:YES

Applications: A

Species:A C M O P Q

ME:YES

Applications: A



Species:A C M P

ME:YES

Applications: A

NOTE: SMBCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: LBCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: XLBCVE10 is available in Cherry, Paintable and Maple ONLY.

NOTE: MBCVE10 is available in Cherry, Paintable and Maple ONLY.

80510 - Medium Beaded Cove Molding - MBCVE

Cat. No. PriceMBCVE 191MBCVE10 262

Cat. No. PriceXLBCVE 266XLBCVE10 399

80500 - Small Beaded Cove Molding - SMBCVE

Cat. No. PriceSMBCVE 147SMBCVE10 201

Cat. No. PriceLBCVE 234LBCVE10 342

80520 - Large Beaded Cove Molding - LBCVE

80530 - Extra Large Beaded Cove Molding - XLBCVE

80550 - Molding Extension - ME

• Molding Extension is fi nished on front, top and bottom only.

• Molding Extension is manufactured as part of curved moldings and does not need to be ordered separately. Straight moldings should be ordered with ME when used with curved moldings.

Cat. No. PriceME 104

Details for Straight Installation Shown

Molding Flush WithBottom of Extension

Molding 3/16” Off setFrom Bottom of Extension

ME is designed for two diff erent applications depending on designer preference. Molding can be attached “Flush” with bottom of ME or with a 3/16” off set. See drawings above.

Species:A C M P

ME:YES

Applications: A

Species:A C M P

ME:YES

Applications: A

Species:A C M P

ME:YES

Applications: A


ME:--

Applications: A



Cat. No. PriceStarter Molding Profi ledSMP2 245SMP4 339SMP6 433Starter Molding Profi led FlushSMPF2 245SMPF4 339SMPF6 433Molding Profi ledMP2 137MP4 247MP6 357

80600 - Starter Molding Profi led

• Starter Molding is designed as a “build up” for attachment of Crown Molding to maintain reveals.

• SMP is for Full Overlay or Overlay Styling.

• SMPF is for Inset cabinetry.

• MP can be attached directly to the face frame

• Specify edge profi le. If not specifi ed, #6 eased edge is used.

• Horizontal grain.

Profi les Available

SMP2/SMP4/SMP6 Attach to top of cabinet Starter Molding for Full Overlay or Overlay.

SMPF2/SMPF4/SMPF6 Attach to top of cabinet for Inset.

MP2/MP4/MP6 Applied to face frame of cabinet.

Details for Installation

SMP_ SMPF_


ME:NO

Applications: A

Cat. No. PriceStarter Molding Profi led - 10’SMP2-10 343SMP4-10 475SMP6-10 606Starter Molding Profi led Flush - 10’SMPF2-10 343SMPF4-10 475SMPF6-10 606Molding Profi led - 10’MP2-10 192MP4-10 346MP6-10 500

NOTE: 10’ lengths are available in Maple, Cherry and Paintable only.

10’ Lengths8’ Lengths


26AUGUST2019© Dura Supreme Cabinetry 10-6a

• Straight and L-Shaped VCLV Moldings are available for use with Veneered door styles (i.e. Moda, Moxie, etc.). Moldings are reversible for use as ceiling valance (top) or light valance (under-cabinet).

• Straight VCLV Molding is finished on both faces and edgebanded on one long edge. L-Shaped VCLV is finished on both faces and banded on both long edges.

• Horizontal grain.

Cat. No. PriceStraight MoldingVCLV 168VCLV3 168VCLV6 304L-Shaped MldgVCLV-L 401VCLV-L3 534VCLV-L6 668

80615 - Veneer Ceiling/Light Valance Molding - VCLV


ME:NO

Applications: A


26AUGUST2019 © Dura Supreme Cabinetry10-6b



80650 - Dentil Molding - DTM

Cat. No. PriceDTM 166

Cat. No. PriceRM 116

80850 - Rope Molding - RM

80950 - Decorative Cove Molding - DCM

Cat. No. PriceDCM 121DCM10 172DCMB 363DCMC 363

Cat. No. PriceCM 89CM10 102CMB 363CMC 363

NOTE: Curved DCM is designed for installation directly to the face of the cabinetry (when space allows.)

NOTE: Curved CM is designed for installation directly to the face of the cabinetry (when space allows.)

NOTE: DCM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: CM10 is available in Cherry, Paintable and Maple ONLY.

NOTE: Curved DCM is not available in Hickory.

NOTE: Curved CM is not available in Hickory.

81000 - Cove Molding - CM

Species:C M P

ME:NO

Applications: A

Species:C M P

ME:NO

Applications: A

Species:A C H M O P

ME:NO

Applications: A CB

Species:A C H M O P

ME:NO

Applications: A CB

NOTE: DTM is available in 92” lengths ONLY.



81100 - Chair Rail/Light Valance Molding - CRLVM

81210 - Light Shield Profi led - LSPRO

Cat. No. PriceCRLVM 103

81150 - Light Shield Classic Molding - LSCL

81160 - Light Shield Transitional Molding - LSTR

81220 - Beveled Bottom Molding - BVBM

81230 - Classic Bottom Molding - CLBM

Cat. No. PriceLSCL 133LSCLB 472LSCLC 472

Cat. No. PriceLSTR 133LSTRB 472LSTRC 472

Cat. No. PriceLSPRO 228

Cat. No. PriceBVBM 133

Cat. No. PriceCLBM 108

Profi les Available

Cat. No. PriceCBBMB 166

81232 - Cottage Bead Bottom Molding -CBBMB

Species:A C M P

ME:YES

Applications: A

Species:A C H M O Q P

ME:NO

Applications: A


ME:NO

Applications: A

Species:A C M O P

ME:NO

Applications: A CB

Species:A C M O P Q

ME:NO

Applications: A CB


ME:NO

Applications: A

Species:C M O P Q

ME:NO

Applications: A



81350 - Bead Molding - BM

Cat. No. PriceBM 79BMB 363BMC 363

NOTE: Curved BM is designed for installation directly to the face of the cabinetry (when space allows.)

NOTE: Curved BM is not available in Hickory.

Cat. No. PriceTM 79

Cat. No. PriceFM 87

81400 - Trim Molding - TM

81450 - Face Molding - FM

81500 - Outside Corner Molding - OSCM

81550 - Decorative Outside Corner Molding - DOSCM

81560 - Outside Corner Molding 135° - OSCM135

Cat. No. PriceOSCM 88

Cat. No. PriceDOSCM 116

Cat. No. PriceOSCM135 125


ME:NO

Applications: A CB


ME:NO

Applications: A

Species:A C M O P Q

ME:NO

Applications: A


ME:NO

Applications: A

Species:A C H M O P

ME:NO

Applications: A

Species:A C H M O P

ME:NO

Applications: A



Cat. No. PriceFBM 247FBM6 345

81700 - Broad Scribe Toe - BST

Cat. No. PriceBST 147

Cat. No. PriceFBCRM 247

Cat. No. PriceFBCVE 247

81750 - Additional Toe Board Molding - TBMCHG

Cat. No. PriceTBMCHG 101

• Toe Board Molding in suffi cient quantitiesis automatically included to complete a job. If additional lengths are required, order TBMCHG.

• 1/4” thick veneer core plywood, 4-1/2” high. 8 foot lengths only. Face and each end are fi nished.

81800 - Base Shoe Molding - BSM

81802 - Base Shoe Molding Square - BSMS

Cat. No. PriceBSM 75BSMB 363BSMC 363

Cat. No. PriceBSMS 75BSMSB 363BSMSC 363

• Curved BSM fi ts radius of recessed toe only.

NOTE: Curved BSM is not available in Hickory.

NOTE: Curved BSMS is not available in Hickory.

81810 - Furniture Base Crown Molding - FBCRM

81820 - Furniture Base Cove Molding - FBCVE

81850 - Furniture Base Molding - FBM

Profi les Available

• Specify profi le for one long edge.Example: FBM#2


ME:NO

Applications: A


ME:NO

Applications: A


ME:NO

Applications: A


ME:NO

Applications: A


ME:NO

Applications: A

Species:A C H M O P

ME:NO

Applications: A CB

Species:A C H M O P

ME:NO

Applications: A CB



Cat. No. PriceCBNB 129

81950 - Bead Board Molding - BBM

81960 - Shiplap Molding - SLM

• Available in lengths of 36”, 48”and 96” only.

• PMSA is the applied molding usedfor St. Augustine and SunburyHouse door styles.

Cat. No. PriceBBM36 51BBM48 59BBM96 119

82110 - Panel Molding - St. Augustine - PMSA

82120 - Panel Molding - Cottage Bead - PMCB

82130 - Panel Molding - Chapel Hill - PMCHV

Cat. No. PricePMSA 112

Cat. No. PricePMCB 112

Cat. No. PricePMCHV 112

82150 - Mirror Frame Molding - MFRM

82145 - Cottage Bead Nosing Molding - CBNB

• PMCHV coordinates with the ap-plied molding used for Chapel Hill,Marley and Montego door styles.

• Mirror Frame Molding is available in 72” lengths to frame amirror with a matching door style frame.

• Mirror Frame Molding matches the door style (profi le and framewidth) specifi ed on the order unless otherwise specifi ed.

• Back of Mirror Frame molding includes cut-out for mirror.

• Available in 72” lengths only.

• See door style for species availability.

Cat. No. PriceMFRM 161


ME:NO

Applications: A

Species:A C M P

ME:NO

Applications: A


ME:NO

Applications: A

Species:A C M O P

ME:NO

Applications: A

Species:A C M O P Q

ME:NO

Applications: A


ME:NO

Applications: A

Cat. No. PriceSLM 130



82250 - Valances

• Specify the pattern and indicate the width needed. Valances automatically include a 1” extension on each end for trimming (2” extra overall). Example: VAL-D36 (supplied at 38” for fi eld trim.)

• Minimum width = 15”. Maximum width = 94”.

Loose Valance, VAL-D, E, G_, H (specify pattern) $68 per lineal foot (rounded up to the nearest one foot increment)

Decorative Toe Loose, DTL (specify pattern) $72 per lineal foot (rounded up to the nearest one foot increment)

82275 - Decorative Toe Loose• Specify the pattern and indicate the width needed.

DTL automatically includes a 1” extension on each end for trimming (2” extra overall). Example: DTL-D35 (supplied at 37” for fi eld trim.)

• Minimum width = 15”. Maximum width = 94”.

• Top edge is profi led to match the door edge profi le (for D, E, G2 and G3).

• For straight lengths of matching molding (no arch) see Sections 81810, 81820 and 81850.



82300 - Keystone Panel Valance - KPV

• KPV is 15” high and available in 3” increments from 30” - 96” wide.

• KPV is constructed with mortise & tennon joinery only (No miter joints). Inside edge profi le is supplied with “A” or “B” profi le only (whichever profi le most closely coordinates with the door style specifi ed.) Applied molding is not available.

• KPV has 2 3/4” stiles and rails. Raised or fl at panels match the door style specifi ed for the order.

• Center of KPV will accept optional Keystone Block (KEYB) or can be used for a carved applique (ordered separately).

• Panels have horizontal grain (except beaded panel).

• Back of KPV is fi nished. Method of assembly is visible on back side.

• Cut down in width is available.

WIDTH MODIFICATIONS ONLY

KPV is automatically constructed with an “A” or “B” inside edge pro-fi le (whichever profi le best coordi-nates with the specifi ed door style).

Optional Keystone Block

Outside edge of Keystone Block has a 1/8” radius.

Cat. No. PriceKPV30 1654KPV33 1668KPV36 1711KPV39 1741KPV42 1770KPV45 1799KPV48 2011KPV51 2222KPV54 2435KPV57 2653KPV60 2859KPV63 3070KPV66 3282KPV69 3493KPV72 3706KPV75 3917KPV78 4129KPV81 4340KPV84 4553KPV87 4764KPV90 4976KPV93 5184KPV96 5404KEYB 236



82350 - Arched Panel Valance - APV

• APV is 15” high and available in 3” increments from 30” - 96 wide.

• APV is constructed with mortise & tennon joinery only (No miter joints). Inside edge profi le is supplied with “A” or “B” profi le only (whichever profi le most closely coordinates with the door style specifi ed.) Applied molding is not available.

• APV has 2 3/4” stiles and rails. Raised or fl at panels match the door style specifi ed for the order.

• Panels have horizontal grain (except beaded panel).

• Back of APV is fi nished. Method of assembly is visible on back side.

• Cut down in width is available.

WIDTH MODIFICATIONS ONLY

APV is automatically constructed with an “A” or “B” inside edge pro-fi le (whichever profi le best coordi-nates with the specifi ed door style).

Cat. No. PriceAPV30 1587APV33 1601APV36 1643APV39 1673APV42 1699APV45 1728APV48 1931APV51 2134APV54 2338APV57 2543APV60 2743APV63 2949APV66 3150APV69 3353APV72 3558APV75 3761APV78 3965APV81 4168APV84 4371APV87 4573APV90 4776APV93 4979APV96 5190



8240

0 -

Turn

ed P

ost

Sty

le O

pti

on

s

• Tu

rned

Pos

ts a

re a

vail

abl

e lo

ose

or a

tta

ched

to

Fill

ers,

En

d Pa

nel

s a

nd

Dec

ora

tive

En

d Pa

nel

s. T

urn

ed P

osts

are

ava

ila

ble

in s

ever

al d

iffe

ren

t de

sign

s (s

ee d

raw

ings

bel

ow).

C

lea

rly

spec

ify

the

pos

t st

yle

on y

our

orde

r a

nd

add

th

e a

pp

rop

ria

te u

pch

arg

e (i

f a

pp

lica

ble.

)

• A

ll T

urn

ed P

osts

are

ava

ila

ble

31-1

/2”,

34-

1/2”

an

d 40

-1/2

” h

igh

. Fo

r ot

her

hei

ghts

, tri

m t

op b

lock

as

nee

ded

duri

ng

inst

all

ati

on.

Styl

e U

pch

arge

A1

Add

0A

2 A

dd 0

A6

Add

0B1

A

dd 0

B2

Add

0B6

A

dd 0

C1

Add

0C

2 A

dd 0

C6

Add

0D

1 A

dd 0

D2

Add

0D

6 A

dd 0

E1

Add

0E2

A

dd 0

E6

Add

0

*Sty

le G

Pos

ts -

Sp

ecify

Lef

t or

Rig

ht

(Lef

t sh

own)

.

*

Styl

e

Up

char

geF1

Add

0F6

Add

0G

1*

L/R

Add

0G

6*

L/R

Add

0H

1

Add

0H

6

Add

0I1

Add

0I2

Add

0I6

Add

0J1

Add

126

J2

A

dd 1

26J6

Add

126

K1

A

dd 1

26K2

Add

126

K6

A

dd 1

26

Styl

e

Up

char

geL1

Add

126

L2

A

dd 1

26L6

Add

126

M1

A

dd 0

M2

A

dd 0

M6

A

dd 0

N1

A

dd 0

N2

A

dd 0

N6

A

dd 0

O1

A

dd 0

O2

A

dd 0

O6

A

dd 0

P1

A

dd 0

P2

A

dd 0

P6

A

dd 0

Styl

e U

pch

arge

A16

Add

0B1

6

Add

0C

16

A

dd 0

D16

Add

0E1

6

Add

0I1

6

Add

0J1

6

Add

126

K16

A

dd 1

26L1

6

Add

126

M16

Add

0N

16

A

dd 0

O16

Add

0P1

6

Add

0

Thes

e p

osts

coo

rdin

ate

with

Fur

nitu

re V

aniti

es



82450 - Base Turned Posts - Loose

• Specify a Turned Post style. Example: 4QTP3-34-A2

• Loose Base Turned Posts (3-1/2” and 5-1/2” wide) are available as full round, 3/4-round, 1/2-round and 1/4-round.

• Loose turned posts are supplied with an additional 1/2” - 1” for fi eld trimming. See drawing below.

NO MODIFICATIONS

Full Round Three-Quarter Half Round One-Quarter Base Round Base Base Round Base

Cat. No. PriceFull Round4QTP3-31 549*4QTP3-34 567*4QTP3-40 629*Three-Quarter Round3QTP3-31 549*3QTP3-34 567*3QTP3-40 629*

Cat. No. PriceFull Round4QTP5-31 944*4QTP5-34 969*4QTP5-40 1045*Three-Quarter Round3QTP5-31 944*3QTP5-34 969*3QTP5-40 1045*

Cat. No. PriceHalf Round2QTP3-31 360*2QTP3-34 371*2QTP3-40 410*One-Quarter Round1QTP3-31 360*1QTP3-34 371*1QTP3-40 410*

Cat. No. PriceHalf Round2QTP5-31 616*2QTP5-34 637*2QTP5-40 681*One-Quarter Round1QTP5-31 616*1QTP5-34 637*1QTP5-40 681*

3-1/2” Posts 5-1/2” Posts

Pricing shown is a “base price”. Select a Turned Post style and add appropriate style upcharge from Section #82400.

For a complete listing of Turned Posts available see Section #82400


08FEBRUARY2021© Dura Supreme Cabinetry 10-17

82500 - Pilasters - Loose

• Specify style of Pilaster (I - Plain, J - Fluted, K - Reeded). Example: PIL-I

• Loose half-round Pilasters (2 1/2” wide) are shipped as a 3-piece kit for fi eld assembly. Half-round molding is available in two lengths for fi eld trimming and fi tting between the top and bottom blocks.

• PIL includes a top and bottom block with a 47” length of half-round molding. PILT includes a top and bottom block with a 95” length of half-round molding.

NO MODIFICATIONS

Cat. No. PricePIL 334PILT 441

82550 - Bunfoot• Standard cabinet toe space is 3” deep. Bunfeet wider than 3” will require jobsite trimming to fi t within a standard toe space.

NO MODIFICATIONS

Cat. No. PriceBUNFOOT3 205

Cat. No. PriceBUNFOOT5 205BUNFOOT6 205BUNFOOT7 205

Cat. No. PriceBUNFOOT8 205BUNFOOT9 205BUNFOOT10 L/R 205

Cat. No. PriceBUNFOOT11 205BUNFOOT12 205BUNFOOT13 205

NOTE: PILT is available in style I - Plain only.



82600 - Cottage Bead Spacer

Cut to Size, CTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .N/C

• Cottage Bead Spacers are 3/4” thick solid stock with a Cottage Bead nosing profi le on the front edge.

• Shipped loose for fi eld installation.

Cat. No. PriceWall Cabinet SpacersCBS30 119CBS36 119CBS39 157CBS42 157CBS48 157CBS54 184CBS57 184CBS60 184Base/Vanity/Desk Cabinet SpacersCBS28 119CBS31 119CBS34 119CBS40 157Tall Cabinet SpacersCBS84 184CBS90 184CBS93 184CBS96 184


26AUGUST2019© Dura Supreme Cabinetry 10-18a

Cut to Size, CTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .N/C

82650 - Columns (square)

• Constructed with 3/4” thick solid wood with mitered corners.

• Available in 3” x 3” or 6” x 6” dimensions.

• Specify CTS for width, depth and/or height cut downs for the and indicate needed dimension(s). Minimum width/depth is 3” x 3”. Minimum height is 12”.

• Columns are not intended for structural support.

Cat. No. Price3” x 3” 1-Sided Column1CLMN328 (28-1/2” high) 691CLMN331 (31-1/2” high) 771CLMN334 (34-1/2” high) 841CLMN340 (40-1/2” high) 981CLMN348 1171CLMN354 1311CLMN360 1466” x 6” 1-Sided Column1CLMN628 (28-1/2” high) 1381CLMN631 (31-1/2” high) 1521CLMN634 (34-1/2” high) 1671CLMN640 (40-1/2” high) 1961CLMN648 2321CLMN654 2611CLMN660 290





26AUGUST2019 © Dura Supreme Cabinetry10-18b

82660 - Decorative Columns

• Constructed with 3/4” thick solid wood with mitered corners.


ALL OTHER MODIFICATIONS MUST BE QUOTED

• 34-1/2” and 40-1/2” high columns have wide bottom rail sized as a “Flush Toe” (4 1/2” + rail width of selected door style).

• 48”, 54”, and 60” high columns have top and bottom rail to match door style.

• Stiles are 2” wide.

• 6” Columns available with fl at panel only. 9” Columns match the door style panel (raised or fl at).



Decorative Columns - Style “A”

Decorative Columns - Style “B”

PMCHV

PMCHV

Cut to Size (Minimum 6” x 6”), CTS . . . . . . . . . . . . . . . . . . . . . N/C

Molding wraps along 3/4” side of “A” and “B”.

Molding wraps along 3/4” side of “A” and “C”.

• 34-1/2” and 40-1/2” high columns have wide bottom rail sized as a “Flush Toe” (4 1/2” + rail width of selected door style).

• 48”, 54”, and 60” high columns have top and bottom rail to match door style.

• Stiles are 2” wide.

• 6” Columns available with fl at panel only. 9” Columns match the door style panel (raised or fl at).



Decorative Columns - Style “C”




24AUGUST2020© Dura Supreme Cabinetry 10-18c

82660 - Decorative Columns

Cat. No. Price3” x 3” 1-Sided Column1CLMNB334 (34-1/2” high) 2221CLMNB340 (40-1/2” high) 2373” x 3” 2-Sided Column2CLMNB334 (34-1/2” high) 4842CLMNB340 (40-1/2” high) 5163” x 3” 3-Sided Column3CLMNB334 (34-1/2” high) 5973CLMNB340 (40-1/2” high) 6413” x 3” 4-Sided Column4CLMNB334 (34-1/2” high) 7114CLMNB340 (40-1/2” high) 766

Cat. No. Price6” x 6” 1-Sided Column1CLMNB634 (34-1/2” high) 3051CLMNB640 (40-1/2” high) 3346” x 6” 2-Sided Column2CLMNB634 (34-1/2” high) 6272CLMNB640 (40-1/2” high) 6866” x 6” 3-Sided Column3CLMNB634 (34-1/2” high) 7873CLMNB640 (40-1/2” high) 8656” x 6” 4-Sided Column4CLMNB634 (34-1/2” high) 9504CLMNB640 (40-1/2” high) 1048

Column B - 3”

Cat. No. Price6” x 6” 1-Sided Column1CLMNA634 (34-1/2” high) 2901CLMNA640 (40-1/2” high) 3191CLMNA648 3551CLMNA654 3841CLMNA660 4136” x 6” 2-Sided Column2CLMNA634 (34-1/2” high) 7352CLMNA640 (40-1/2” high) 7942CLMNA648 8962CLMNA654 9772CLMNA660 10586” x 6” 3-Sided Column3CLMNA634 (34-1/2” high) 10193CLMNA640 (40-1/2” high) 10973CLMNA648 12313CLMNA654 13393CLMNA660 14476” x 6” 4-Sided Column4CLMNA634 (34-1/2” high) 13054CLMNA640 (40-1/2” high) 14034CLMNA648 15714CLMNA654 17064CLMNA660 1841

Cat. No. Price9” x 9” 1-Sided Column1CLMNA934 (34-1/2” high) 3731CLMNA940 (40-1/2” high) 4171CLMNA948 4711CLMNA954 5141CLMNA960 5589” x 9” 2-Sided Column2CLMNA934 (34-1/2” high) 9802CLMNA940 (40-1/2” high) 10682CLMNA948 12212CLMNA954 13422CLMNA960 14649” x 9” 3-Sided Column3CLMNA934 (34-1/2” high) 13433CLMNA940 (40-1/2” high) 14603CLMNA948 16623CLMNA954 18243CLMNA960 19859” x 9” 4-Sided Column4CLMNA934 (34-1/2” high) 17114CLMNA940 (40-1/2” high) 18584CLMNA948 21114CLMNA954 23134CLMNA960 2515

Column A - 6” Column A - 9”

Column B - 6”

Column C - 6” Column C - 9”

Cat. No. Price6” x 6” 1-Sided Column1CLMNC634 (34-1/2” high) 3651CLMNC640 (40-1/2” high) 3946” x 6” 2-Sided Column2CLMNC634 (34-1/2” high) 8862CLMNC640 (40-1/2” high) 9456” x 6” 3-Sided Column3CLMNC634 (34-1/2” high) 12453CLMNC640 (40-1/2” high) 13236” x 6” 4-Sided Column4CLMNC634 (34-1/2” high) 16064CLMNC640 (40-1/2” high) 1704

Cat. No. Price6” x 6” 1-Sided Column1CLMNC934 (34-1/2” high) 4481CLMNC940 (40-1/2” high) 4926” x 6” 2-Sided Column2CLMNC934 (34-1/2” high) 11312CLMNC940 (40-1/2” high) 12196” x 6” 3-Sided Column3CLMNC934 (34-1/2” high) 15693CLMNC940 (40-1/2” high) 16866” x 6” 4-Sided Column4CLMNC934 (34-1/2” high) 20124CLMNC940 (40-1/2” high) 2159


24AUGUST2020 © Dura Supreme Cabinetry10-18d

82750 - Solid Stock - Shaping Charge

• Always specify the “cross-grain” dimension fi rst. Specify the code, then specify width (cross-grain) x length (with the grain). Example: SS3/4 x 3” (cross grain) x 96”. Grain will run in the same direction as the length dimension.

• Widths up to 6-5/8” wide may be ordered up to a maximum of 120” long. For lengths over 96” up to 120” specify SSXL. Widths over 6-5/8” up to 10-7/8” wide can be ordered up to a maximum of 84” long.

• Minimum width is 3/4”.

• Solid Stock is fi nished F1S as standard (fi nished on one face and both long edges). Additional edges and the second face can be fi nished for an upcharge. See pricing chart below.

Finish One Face and All Edges, F1S-AE . . . . . . . . . . . . Add 10% to Solid Stock Price

Finish Second Face, F2S . . . . . . . . . . . . . . . . . . . . . . Add 50% to Solid Stock Price

Finish Second Face and All Edges, FAS . . . . . . . . . . . . Add 60% to Solid Stock Price

Shaping Charge, SHPCHG . . . . . . . . . . . . . . . . . . . . Add 50% to Solid Stock Price

Cat. No. Price/Sq FtSolid StockSS 90SSXL* 136*Lengths over 96” to 120”.*96” = maximum length for Rustic Hickory.

Optional Edge Profi le Shaping

• Specify profi le and indicate which edges to be profi led (long edge(s) or short edge(s) - and which face if applicable).

• One shaping charge applies (no matter how many edge are being profi led).

• Profi les are applied to face of solid stock unless back (second face) has been clearly specifi ed.

• See Profi le Chart for minimum sizes.

• Profi led edges are always fi nished. Appropriate fi nish upcharges must be specifi ed and applied. Example: SS 3/4” x 3” x 42”, F2S, Profi le two long edges.

Example shown: SS 3/4” x 3” x 18” F1SProfi le one long edge.

Example shown: SS 3/4” x 3” x 18” F1SProfi le two long edges.

Profi les

Available

Minimum Width for machining

one edge

Minimum Width for machining

two edges

3/4” 2”

3/4” 2”

3/4” 1-1/2”

3/4” 1-1/2”

3/4” 1-1/2”

1” 2”

3/4” 1-1/2”

3/4” 2”

3/4” 1-1/2”



82800 - Wood Tops

• Specify overall size (including applied solid stock or molding). Always specify the width (cross-grain) dimension before the length. To order, indicate edge height x width (cross-grain) x length (with the grain). Example: WT1-1/2” (edge height) x 25” (cross-grain) x 48” (with the grain)

• Wood tops are available with 3/4” plywood or funiture-board with solid stock or molding applied to the specifi ed edges. Price includes panel and applied solid stock (3/4” or 1-1/2”) or molding.

• Maximum panel size is 48” wide x 96” long excluding solid stock or moldings.

• Maximum nonstandard, “Extra Long” (Veneer core only) panel size is 25” x 120” excludingsolid stock or moldings. Exception: Not available in Rustic Hickory.

• Non-Standard Wood Top code must be specifi ed for any wood top with angles, notches or clipped corners, or for any Extra-Long top (over 96”).

Example shows 1-1/2” high solid stock applied to front and left edge.

Specify edge treatments from selections below and indicate which edges of

wood top that treatment is to be applied to - a sketch is recommended.

Flush Solid Stock Applied Shaped Solid Stock Applied Molding Applied

Wood Top Profi les

Solid stock applied to front edge.

3/4”, #10 Profi le shown

3/4”, #1 Profi le shown

1½”, #1 Profi le shown

Solid stock applied to front edge with shaping. Shown with profi le on top edge. If bottom edge is to be profi led, specify clearly.Specify profi le from chart below.

NOTE: If wood tops are ordered over 96” long and the molding edge treatment is not available in lengths longer than 96”, the molding will be spliced to match the countertop width.

Wood Tops are priced by the square foot, all styles the same price. Calculate overall square footage and add:

Wood Top with Furniture Board Core, (not available in Rustic Hickory) WT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$90 per square foot

Wood Top with Veneer Core Plywood, WTVC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$104 per square foot

Non-Standard Wood Top with Furniture Board Core, (not available in Rustic Hickory) WTNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$124 per square foot

Non-Standard Wood Top with Veneer Core Plywood, WTVCNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$139 per square foot

Cottage Bead Nosing Molding shown

Wood Top Non-Standard



82850 - Doors Only (Extra/Loose)

NOTE: No modifi cations that affect curved door radius.

• Specify door style and cabinet that door is to fi t, or size of special door.

• Specify if doors are to be drilled for hinges, and hinge direction if applicable. Hinges are included in price. If hinges are not needed, specify “no hinges” on the order for no charge.

• If hinge direction is not specifi ed, doors will be hinged left.

• When Hinge None is specifi ed, holes required for fi nishing will be visible on back of door.

• Door Only modifi cation is not available for entire orders.

Hinged door sizing: Width:

Maximum = 24”

Minimum - based on door style – see individual door style page for limitations.

Height:

Maximum = 86”

Up to 48” high, doors will be single panel in height.

Over 48” high, doors will be double panel in height.

For a single panel door, specify FHDNIR. Exception: Single panel doors over 48” high are not available with solid wood panels (Raised Panel or Panel Plus.)


Non-hinged door sizing: Width:

Maximum = 36”

Up to 27” wide - doors will be single panel in width.

Over 27” wide – doors will be double panel in width.

For a single panel door, specify FWDNIM. Exception: Single panel doors over 27” wide are not available with solid wood panels (Raised Panel or Panel Plus.)


Height:

Maximum = 96”

For doors up to 48” high, panels will be single styled in height.

For doors over 48” high, panels will be double styled in height.

For a single panel door, specify FHDNIR. Exception: Single panel doors over 48” high are not available with solid wood panels (Raised Panel or Panel Plus.)


Camden and Summit door style sizing limitations - hinged or non-hinged:

Maximum width = 24”

Maximum height panel is 64”. Panels higher than 64” will be two equal panels (pinned together if hinged).

Door Only (standard), DR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $119 per square footage of door

Door Only (curved), DRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $1573 per door

Full Height Door No Intermediate Rail (non-warranty), FHDNIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No Charge

Full Width Door No Intermediate Mullion (non-warranty), FWDNIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No Charge

NOTE: When ordering Doors Only, remember to include all modifications to the doors and their prices (mullions, clear glass, leaded glass, etc.).



83010 - Hinge Angle Restriction Clip

83000 - Hinges (Extra/Loose)• Supplied in pairs. Installation screws provided.

• Specify hinge and fi nish. When ordering concealed hinges, specify cabinet type. Example: DCW, BCW, etc..

Cat. No. PriceHSOL (105 degree concealed standard overlay hinge - Nickel fi nish only) 46HSOLSC (170 degree concealed standard overlay hinge for square corner units - Nickel fi nish only) 107HSOLSOFTC (110 degree concealed standard overlay soft close hinge - Nickel fi nish only) 46HFOL (110 degree concealed full overlay hinge - Nickel fi nish only) 56HFOLSC (170 degree concealed full overlay hinge for square corner units - Nickel fi nish only) 107HFOLSOFTC (110 degree concealed full overlay soft close hinge - Nickel fi nish only) 56HBF (Hinges for connecting square corner doors - Nickel fi nish only) 100HIBLK (Inset hinge - Flat Black) 56HINSC (Inset hinge - Polished Chrome) 56HINSN (Inset hinge - Sterling Nickel) 56HINSV (Inset hinge - Verona Bronze) 56HINSW (Inset hinge - Wrought Iron) 56HCINS (Concealed Inset Hinge - Nickle Finish only) 56HCINSSOFTC (Inset hinge - soft close - Nickel fi nish only) 56HTDF (Tip down front) 69HPD (Pocket door hinges) 69

NOTE: See door style section for drawer front size limitations.

• Extra or replacement drawer fronts.

• Specify drawer/door style and cabinet that drawer front is to fi t or size of drawer front.Cat. No. PriceDFR1 243

83050 - Drawer Front Only (Extra/Loose)

• Angle restriction clip is available for concealed overlay and full overlay Soft-Close® hinges to restrict the angle of opening to 86°.

• Loosen and remove the installation screws to detach the door from the frame. Click the hinge arm to the closed position. Insert therestriction clip into the base of the hinge arm. Rotate the hinge arm to the open position to secure the clip. Reattach the hinge to the frame.

Hinge Angle Restriction Clip for Standard Overlay and Full Overlay doors, HARC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7 Each

Hinge Angle Restriction Clip for Inset doors, HARC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$7 Each



Cat. No. Price / Sq FtASW 42

• A 3/4” thick, wood veneer shelf with edge banding on front edge is supplied in wood species and fi nish to match the order.

• Shelf clips included.

• Specify cabinet that shelf is to fi t or the actual size of the shelf.

Edge Banding Applied, EBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10% per edge

ADDITIONAL EDGE BANDING - EBA

• Specify which additional edges are to be banded.

83300 - Shelf (Additional Veneer Finished Shelf- Loose)

83100 - Drawer Box (Extra/Loose)• Dovetailed drawer box, full-extension drawer guides, and all screws for fi eld installation.

Drawer guides are installed to drawer box.

• Available in 2” height increments from 2” - 10”.

• Specify the width and depth of the cabinet the drawer is to be installed in and drawer location in the cabinet.

THE FOLLOWING COMBINATIONS OF DRAWER BOXES MAY BE ORDERED:

DWBW Drawer box only.

DWBWG Drawer box with complete set of guides.

DWRW Drawer box, complete set of guides and drawer front.

NO MODIFICATIONS

Cat. No. PriceDWBW 187DWBWG 399DWRW1 653

83150 - Drawer or Roll-Out Shelf Guide - Undermount (Extra/Loose)• Undermount full-extension drawer guides are sent as a sets and include left and right drawer members and

case members for one (1) drawer or Roll-Out Shelf (with all screws for installation).

• Specify the cabinet the drawer guides are to be installed in. Guides available for 12”, 15”, 18”, 21”, and 24” deep cabinets.

Cat. No. PriceBMOTFEG 212

83200 - Drawer Guide - Side Mount Full Extension - (Extra/Loose)• 100 pound capacity, side mount, full extension guides are sent as a set and include left and

right drawer members and case members for (1) drawer installation.

• Specify the cabinet the drawer guides are to be installed in. Guides available for 12” or 15” deep cabinets.

Cat. No. PriceFEGSM 168

Side mount full extension guide is required and standard on the following cabinetry:

•Wall Pull-out Spice Rack

• ASSCM is a 3/4” thick, natural Maple supreme coat shelf, with PVC edge banding.

• AS is a 3/4” thick, natural Maple veneer plywood shelf.

• Shelf clips included.

• Specify cabinet that shelf is to fi t or the actual size of the shelf.

Edge Banding Applied, EBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10% per edge

Cat. No. Price / Sq FtASSCM 28AS 44

ADDITIONAL EDGE BANDING - EBA

• Specify which additional edges are to be banded.

83250 - Shelf (Additional for Standard Interior - Loose)

For Premium Maple Drawer Boxes, add $144 per Drawer Box and specify PM in place of the “W”. Example: DWBW becomes DWBPM Available in 1” height increments from 2” - 10”.



83350 - Shelf and Rail (Additional, to Match Order - Loose)

• 3/4” thick shelf with 3/4” x 1-1/2” solid stock rail attached to front and back of shelf. Shelves are fi nished on both sides.

• Support rails have an eased edge on top and bottom edges.

• Minimum shelf depth is for a 6”deep cabinet.

• Specify cabinet shelf is to fi t or the actual size of shelf. Maximum length = 60”. Maximum depth = 24”.

NOTE: Shelf and rail option is not available in curved cabinets.

TO PRICE SHELF AND RAIL SHELVES LOOSE:

1. Calculate square footage of wood shelving to match order and use ASW pricing.

2. Add “Convert Shelves to Shelf and Rail” - SR upcharge.

Additional Shelf Wood, ASW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$42 per sq ft

Plus (+)

Shelf and Rail, SR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add $77 per shelf

Additional Shelf Wood, ASW ........................................................................................................................................................................... $44 per sq ft

Plus (+)

Convert Shelves to Flush Furniture Shelf, Wood, FFSW ............................................................................................................................. Add $243 per shelf

83360 - Flush Furniture Shelf, Wood or High Pressure Laminate (Additional, to Match Order - Loose)

• Two 3/4” thick shelves are attached together with a solid front and back edge. Finished on top, bottom and both banded edges.

• Eased edge on the top and bottom edges.

• Minimum shelf depth = 6”.

• Specify cabinet that shelf is to fit or the actual size of shelf. Maximum length = 60”. Maximum depth = 24”.

TO PRICE FLUSH FURNITURE SHELVES LOOSE:

1. Calculate square footage of shelving to match order and use ASW pricing.

2. Add “Convert Shelves to Flush Furniture Shelf” - FFSW upcharge.

83375 - Floating Shelf

• Floating Shelf includes a steel bracket and wood hanger strip for attachment to studs. If depth of shelf is reduced to less than 10-1/2”, steel bracket must be fi eld cut.

• Solid stock is attached to front and sides.

• Installation instructions are included.

• Weight capacity = 5 lbs/lineal foot.

NO HEIGHT MODIFICATIONS

Cat. No. Price2-3/4” ThickFS24 349FS36 429FS48 614FS60 722FS72 826FS84 970FS96 990Cut to Size, CTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . N/C

Steel Installation Bracket



83405 - Coat Hook (Extra/Loose)

• Coat hooks are shipped loose for fi eld installation.

• Screws (with matching fi nish) are included.

Cat. No. Price9090 (Polished Brass) 619091 (Polished Chrome) 449092 (Brushed Nickel) 489093 (Weathered Nickel) 449094 (Satin Black) 449095 (Oil Rubbed Bronze) 659096 (Verona Bronze) 709098 (Weathered Iron) 70

• Specify wood species and fi nish color.

TOUCH-UP KIT INCLUDES:

• Bottle of touch-up material for stain or paint.

• Miscellaneous touch-up materials applicable to the particular fi nish (i.e. putty stick, topcoat, glaze, etc.)

NOTE: A Touch-Up Kit is included at no charge for each style line with a unique color.(Touch-up Kit is not included with Job Completion Orders.}

Cat. No. PriceTKCHG 47

83550 - Stain (Sent Loose)• Standard stains are available in pints, quarts or gallons for use on

job site.

• When a Glazed Finish is ordered, Stain and Glaze is supplied. For example, if a quart is specifi ed, one quart of Stain and one quart of Glaze is supplied. The charge will be for two quarts.

• Toner will be supplied when needed.

Dura Supreme fi nishes are applied with specialized equipment, therefore fi eld application may result in a slightly different shade than factory fi nish. Dura Supreme recommends that stain be applied on various sample pieces before fi nal application to develop a technique for fi eld application that will assure a close color match.

Finishes That Are NOT Available Loose

-Paint Colors -Natural -Primer -Conversion Varnish Topcoat -Paint/Accent Finishes -Paint/Glaze

Product Cat. No. PricePintStain Only STNPT 96Stain & Glaze STNPTGLZ 148Glaze Only GLZPT 96QuartStain Only STNQT 111Stain & Glaze STNQTGLZ 171Glaze Only GLZQT 111GallonStain Only STNGL 308Stain & Glaze STNGLGLZ 475Glaze Only GLZGL 308

• Available for touch-up use for all Paint/Accent colors.

• Follow application instructions and then apply top coat.

Cat. No. PriceACNTPEN 52

Available Colors Black Sienna Brown Slate Pewter

83555 - Accent Pens

83500 - Touch-Up Kit (Extra)

83400 - Shelf Clips, Acrylic (Extra/Loose)

• Extra adjustable shelf clips are supplied 4 clips per bag.

Shelf Clips, SC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$12 per bag

NOTE: Air shipment is not available.



• Dish Storage Drawer Kit includes 8 posts, a pegboard base plate and large bumper pads for jobsite installation. Base plate can be cut to fi t drawer boxes or deep roll-out shelves for cabinets up to 36” wide.

• Posts are solid wood with a clear topcoat and are 6-5/16” high.

• Posts can be mounted in any of the pre-drilled holes (1-1/4” spacing) of the base plate and secured with a fastening nut. Posts secure stacks of dishware for convenient storage in drawers.

Pegboard Base Plate 36 X 24 and 8 Posts, DSD-KIT36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$828

Additional Package of 4 posts, DSD-POSTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$216

83630 - Dish Storage Drawer Kit (Extra/Loose)

• Kit consists of mounting “U” tracks and one tray divider panel (1/2” thick natural Maple, 22-5/8” deep x 26-1/4” high). Sized for installation in 24 deep, BFD only.

• Divider is removable.

• Shipped loose for fi eld installation.

Cat. No. PriceTDB 137

83450 - Tray Divider Base Kit

83650 - Roll-Out Shelf Kit, Flat (Sent Loose)

• ROSF is made in wood species and fi nish to match cabinet interior.

• Maximum of 3 ROSF per standard base, vanity base, or desk base cabinet, 4 ROSF per BFD, VFD, or DFD cabinet, and 11 ROSF in standard utility cabinet opening.

• ROSF includes 1 Roll-out Shelf with Full-Extension undermount guides for fi eld installation.

SHIM POSTSShim posts are supplied in various lengths to match the number of ROSF shelves in the Kit specifi ed. They are 6-11/16” high for 1 ROSF, 18-1/32” high for 2 ROSF, 26-27/32” high for 3 ROSF, and 54-9/16” high for 4 or 5 ROSF. Shim posts can be cut to length in the fi eld for use in special height cabinets.

Flat Roll-out Shelf, ROSF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $329 per ROSF

Cut to Fit Flat Roll-Out Shelf (Width only), CFROSW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .N/C

Component Lip, COMPLIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Add $40 per ROSF

• Lacquer-based touch up material supplied in 13 ounce aerosol can for fi eld application.

• May be applied over our conversion varnish top coat.

• Follow application instructions.

83600 - Touch-Up Aerosol Cans

NOTE: This material is recommended for use by experienced fi nishing technician only. For touch up use, existing top coat should be thoroughly scuff sanded before application to ensure adhesion. Test in an inconspicuous area fi rst.

Cat. No. PriceSPRAYCAN15CTP Matte 15 degree clear touch up lacquer based top coat 102SPRAYCAN35CTP Gloss 35 degree clear touch up lacquer based top coat 102SPRAYCANPNT* Touch up lacquer based paint top coat - specify color 102

*Specify paint color from availability chart at above right.

NOTE: Not available with Custom Colors.

Available ColorsAntique White

Black Moonstone Cashmere Pearl Classic White Silver Mist Graphite Storm Gray Latte White Linen White Zinc +Curated Colors



83700 - Roll-Out Shelf Kits - 2” High, 4” High or 8” High

• Dovetailed Roll-out Shelves with a natural finish are available 2”, 4” or 8” high.

• Roll-out Shelves are priced as single units. Specify quantity and cabinet for installation. Example: 2, ROS30 for B30

• ROSK includes 1 Roll-out Shelf with Full-Extension undermount guides, 4 shim posts, and installation materials for fi eld installation.

• Minimum cabinet depth is 12”. Minimum cabinet width is 9-3/8” (10-1/2” in inset).

• For cabinets that are cut down in width, specify “Cut to Fit Roll-Out Shelf (width only)” - CFROSW and cabinet width on order.

• 39” through 42” wide cabinets require a partition installed behind the center mullion unless the Butt Door modifi cation is specifi ed.

A PARTITION MUST BE ORDERED SEPARATELY (SEE BELOW) FOR ADJUSTABLE SHELF AND/OR ROS “SIDE-BY-SIDE” INSTALLATION.

Roll-Out Shelf Kit

Roll-Out Shelf Kit

shown with Roll-Out Shelf Partition Kit

Cat. No. PriceROSKIT - 4” HighROSK12* 233ROSK15* 245ROSK18* 245ROSK21* 269ROSK24* 269ROSK27* 305ROSK30* 305ROSK33* 329ROSK36* 329ROSK39* 362ROSK42* 362ROSK30*P 245ROSK33*P 245ROSK36*P 245ROSK39*P 269ROSK42*P 269ROSK45*P 269ROSK48*P 269

Cat. No. PriceROSKIT - 2” HighROSK2-12* 233ROSK2-15* 245ROSK2-18* 245ROSK2-21* 269ROSK2-24* 269ROSK2-27* 305ROSK2-30* 305ROSK2-33* 329ROSK2-36* 329ROSK2-39* 362ROSK2-42* 362ROSK2-30*P 245ROSK2-33*P 245ROSK2-36*P 245ROSK2-39*P 269ROSK2-42*P 269ROSK2-45*P 269ROSK2-48*P 269

Cat. No. PriceROSKIT - 8” HighROSDK12* 392ROSDK15* 413ROSDK18* 413ROSDK21* 446ROSDK24* 446ROSDK27* 494ROSDK30* 494ROSDK33* 530ROSDK36* 530ROSDK39* 583ROSDK42* 583ROSDK30*P 413ROSDK33*P 413ROSDK36*P 413ROSDK39*P 446ROSDK42*P 446ROSDK45*P 446ROSDK48*P 446

4” High Roll-Out Shelf 1 Kit



SHIM POSTSShim posts are supplied in various lengths to match the number of ROSF shelves in the Kit specifi ed. They are 6-11/16” high for 1 ROSK, 18-1/32” high for 2 ROSK, 26-27/32” high for 3 ROSK, and 54-9/16” high for 4 or 5 ROSK. Shim posts can be cut to length in the fi eld for use in special height cabinets.

ROLL-OUT SHELF PARTITION KITS:

Roll-Out Shelf Partition Kit (Base cabinet height), BROSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$234

Roll-Out Shelf Partition Kit (Base Full Door cabinet height), BFDROSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$234

Roll-Out Shelf Partition Kit (Vanity Base cabinet height), VBROSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$234

Roll-Out Shelf Partition Kit (Vanity Base Full Door cabinet height), VFDROSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$234

Roll-Out Shelf Partition Kit (Tall Utility cabinet height), TROSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$423

* = Cabinet depth, specify 12, 18, 21 or 24, and remember to order the appropriate Roll-Out Shelf Partition Kit below.

CabinetMaximum 2” ROS

Maximum 4” ROS

Maximum8” ROS

Standard Base

5 3 2

BFD 7 5 2

Standard Vanity Base

4 3 1

VBFD 5 4 2

Tall 14 11 5

For Premium Maple Roll-Out Shelves, add $144 per Roll-Out Shelf and specify PM at the front of the code.Example: PMROSK42



83810 - Wood Brackets

Cat. No. PriceWB3X4 115WB4X4 115WB5X5 126WB5X7 126WB6X6 138WB9X9 153WB12X12 165

• 3/4” thick solid wood with 1/4” radius on both front curved edges. 2” wide wall plate has 1/4” radius on sides and bottom edge.

• To remove the wall plate, specify “no wall plate” for no charge.• Grain direction is vertical.• Sized depth X height. Example: WB3X4 = 3” deep X 4” high.

NO MODIFICATIONS

NO MODIFICATIONS

* Code signifi es the size of the bracket. For fi nished dimension with wall plate, add 5/8” to height and 3/4” to depth

Cat. No. PriceCSUPA 366

Cat. No. PriceMMCA 217

83820 - Countertop Support

83800 - Mini Molding Corbels - MMCA

NO MODIFICATIONS



83830 - Transitional Corbels

Cat. No. PriceCRBL-A 454

Cat. No. PriceCRBL-A2 454

Cat. No. PriceCRBL-A3 366

• CRBL-A is used on “Pillars” on Independent Platform Hoods and some “Towers” on Mantel Hoods with “Transitional” styling.

• CRBL-A2 is used on Fireplace Mantels with “Transitional” styling.

• CRBL-A3 is used on Integral Hoods (INTHOOD) with “Transitional” styling.

83840 - Decorative End Bracket

• Top and back edges are square and may be trimmed for installation.

NO MODIFICATIONS

Cat. No. PriceDEBA15 542DEBA18 623DEBB15 511DEBB18 555DEBC15 637DEBC18 718

NO MODIFICATIONS

NOTE: Not availabe in Quarter-Sawn White Oak



Dura Supreme offers a selection of carved corbels in our standard program. Carvings are ordered according to the dealer’s selections and are shipped from Dura Supreme fi nished.

NOTE: If any carved product is ordered and later changed or cancelled by the dealer, the original order cannot be cancelled and will be fi nished, charged for and sent to the dealer as ordered.

• Dura Supreme places all orders directly with the manufacturer for these products based on the dealer’s orders.

• Availability of these products from the carving manufacturers may affect our order lead times.

• Available in Maple and Cherry only.

• Variations in color and appearance should be expected on some individual pieces and/or between similar pieces due to the carving process.

NO MODIFICATIONS

NOTE: For orders including distressing and hand detailing Dura Supreme will apply only subtle distressing/detailing to corbels.

CBL-BRC4

CBL-TR2

CBL-WA3

CBL-BRC3

CBL-TR3

CBL-WA2

CBL-BRC2

CBL-TR1

CBL-LIN02

Cat. No. LooseCBL-BRC2 658CBL-BRC3 745CBL-BRC4 873CBL-LIN02 930CBL-TR1 674CBL-TR2 879CBL-TR3 873CBL-WA2 699CBL-WA3 1018

* Specify wood species * at end of code: * “M” = Maple, * “C” = Cherry

87000 - Corbels



Return to Chapter Menu:

MOLDING & MISC. CRESTWOODCATALOG · 2021. 2. 5. · Molding Extension (ME) to align with the curved...

Documents

Transcript of MOLDING & MISC. CRESTWOODCATALOG · 2021. 2. 5. · Molding Extension (ME) to align with the curved...