Module Config User Manual

User Manual ModuleConfig Software

Netop Technology Co., Ltd Tel: +86 21 6921 4567 B3, No.303 XinKe Rd, Qingpu Industrial Zone, Fax: +86 21 6921 3655 Shanghai, China P.C: 201707 www.netop-technology.com

User Manual

(ModuleConfig Software)

Manual Version 1.0

No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated.

In any form or by any means without the prior written permission of Netop Technology Co., Ltd

Copyright 2010 Netop Technology Co., Ltd. All rights reserved.



- 1 -

Contents Hardware and Software Requirements .................................................. 2

Chapter 1 ................................................................................................. 3

Module Config Introduction .................................................................... 3

Connecting Methods.................................................................................... 3

Functions .................................................................................................. 3

ModuleConfig Interface ............................................................................... 4

Chapter 2 ................................................................................................. 5

ModuleConfig Install & Remove .............................................................. 5

ModuleConfig Install ................................................................................... 5

ModuleConfig Remove ................................................................................. 6

Chapter 3 ................................................................................................. 7

Configuration management .................................................................... 7

Set Communication/Local check ................................................................... 7

Com Port Configuration ............................................................................... 7

Chapter 4 ................................................................................................. 8

Device Operation ..................................................................................... 8

Proerty ..................................................................................................... 8

Configuring the Device ................................................................................ 9

The scope of hardware address: ................................................................... 9

Monitoring parameters interface description ................................................. 10

Chapter 5 .............................................................................................. 13

Others ................................................................................................... 13

Data Send & Receive interface .................................................................... 13

Version information .................................................................................. 13



2

Hardware and Software Requirements

Supported Operating Systems: Windows XP ; Windows Server 2003; Windows Server 2008; Windows Vista

Processor: 1GHz Pentium processor or equivalent (Minimum); 2GHz Pentium processor or equivalent (Recommended)

RAM: 256 MB (Minimum); 1GB (Recommended) Hard Disk: Up to 500 MB of available space may be required ; 1GB (Recommended) DVD Drive: required Display: 1024 x 768 high color, 16-bit (Minimum); 1280 x 1024 high color, 32-bit

(Recommended)



3

C h a p t e r 1

Module Config Introduction Connecting Methods

1. Local Communication via RS232-485 cable.

Functions

1. Control FunctionsParameters of devices can be configured via local communication. 2. Set & Search FunctionsCurrent parameter settings and alarm can be displayed.



4

ModuleConfig Interface

Monitoring parameter list of the main interface

Data Send & Receive

Device Info.

Communication Mode



5

C h a p t e r 2

ModuleConfig Install & Remove ModuleConfig Install

1. Double click the Setup.exe file in ModuleConfig installation folder 2. ModuleConfig installation interface ->Select path ->Click Next 3. Continuously click Next 4. Click Close and ModuleConfig installation finished



6

ModuleConfig Remove

1. Select program-Netop -> Uninstall ModuleConfig 2. ModuleConfig remove interface -> Select Yes



7

C h a p t e r 3

Configuration management

Set Communication/Local check

1. Communication PortSelect the correct port number 2. Communication SpeedDefault: 9600

Module Communication Speed: Default: 57600

3. Communication Timeout10 Sec.

1. R Switch: To refresh the serial port 2. Start: To establish connection between the computer and devices when selected, or

to terminate.

Com Port Configuration

Note: Communication Port represents to the serial port used by the computer. Usually, serial port of

the computers default setting is COM 1

For the latest laptop, which is not equipped with serial port, we have to create the serial

port by USB-Serial conversion cable. In this condition, the COM port will not be COM1,

but COM5 or COM6 etc.



8

C h a p t e r 4

Device Operation Proerty

1. Command Base Info. --- Basic information module parameters

Example

Parameters --- Monitoring information module parameters

Example



9

2. Module AddressSelect the module type(Display Hexadecimal) 3. Device NumberSelect the equipment type (Always choose 01) 4. Protocol TypeSelect the protocol (Always choose 01) 5. Protocol Version(Always choose 01)

Configuring the Device The scope of hardware address:

Module 485 communications hardware address

No. Items Description Scope 1 DCM-MB Main Board 0x00~0x0F 2 CBM Combo Module 0x10~0x0F 3 LNA Low Noise Amplifier 0x20~0x2F 4 FCM Frequency Control Module 0x30~0x3F 5 PAM Power Amplifier Module 0x40~0x4F 6 ICS Interference Cancellation System 0x50~0x5F 7 LFC LNA+FC 0x60~0x6F 8 LPA LNA+PA 0x70~0x7F 9 DRM Driver Module 0x80~0x8F

10 DCM-EX Extend 0x90~0x9F 11 FOM Fiber Optical Module 0XA0~0XAF 12 DCM-HI Human Interface 0xF0 13 DCM-BC Battery Charger 0xF1 14 DCM-MO Modem 0xF2



10

Monitoring parameters interface description

Menu

1. Open: Open the config document.xls format Example

.

2. Close: Close the config document



11

3. Get: Search the parameters checked 4. Set: Set the parameters checked

Right-click

5. Line: Display the number of rows 6. Address: Display Module 485 communications hardware address 7. DataType: Display the parameter's data type 8. Range: Display data range 9. Select All: Pick up all items in the interface 10. Inverse All: Clear all items in the interface

Title

11. Name: Display the name of monitoring parameters

12. Value: Set parameters according to type of moduleGrey one is not available 13. Scale: Display monitoring parameters scale 14. GetValue: Display information of equipment. In Alarm Status will display Alarm or

Normal 15. Status: Display feedback or not with Success or Failure, and no operation with

None

16. NoteDisplay note



12



13

C h a p t e r 5

Others Data Send & Receive interface

1. Hex ModeDisplay hexadecimal when selected, or display decimal

2. Clear AllClear all data display in the interface

Version information



14

Revision Record Title Netop ModuleConfig Software User Manual Document NO. Revision Description Date Writer Approved

V1.0 ModuleConfigure Software User Manual Release 2010-05-24 Stella_Qian

Module Config User Manual

Documents

Transcript of Module Config User Manual