Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen...
Transcript of Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen...
![Page 1: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/1.jpg)
X30 Monitor Training Module 5 : Activating Topcon Blockage
![Page 2: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/2.jpg)
Step 1
X30 Module 5: Activating Topcon Blockage
• Begin by entering the setup menu tree by clicking the wrench icon.
![Page 3: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/3.jpg)
Step 2
X30 Module 5: Activating Topcon Blockage
• Navigate to the implement menu by selecting the implement icon.
![Page 4: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/4.jpg)
Step 3
X30 Module 5: Activating Topcon Blockage
• Continue to navigate to blockage by selecting the seeder icon then accessories as shown on the right.
![Page 5: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/5.jpg)
Step 4
X30 Module 5: Activating Topcon Blockage
• Select the Blocked Head Monitor icon and click the enabled option.
• Make sure you click the green check mark after you’ve selected a status.
![Page 6: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/6.jpg)
Step 5
X30 Module 5: Activating Topcon Blockage
• A new screen will then appear with a number of blockage settings.
• Settings should be selected as follows: • Blocked Head Monitor – Enabled
• BH Sensor Type – Standard
• Head Monitoring – Single or Double
![Page 7: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/7.jpg)
Step 6
X30 Module 5: Activating Topcon Blockage
• In the Number of Distribution Heads box, increase or decrease the number to match the number of primary heads on your implement.
• Continue by clicking the green check mark once finished. This saves the setting in the memory.
![Page 8: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/8.jpg)
Step 7
X30 Module 5: Activating Topcon Blockage
• You can now see the proper number of heads displayed.
• Begin the detecting and assigning sensor process by clicking the Detect and Assign Sensors tab below the head numbers.
![Page 9: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/9.jpg)
Step 8
X30 Module 5: Activating Topcon Blockage
• All sensors show In the list now, with their head assignments.
![Page 10: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/10.jpg)
Step 9
X30 Module 5: Activating Topcon Blockage
• Begin assigning heads to sensors by going left to right on your implement, Sensor 1 is on Head 1 and/or ICT section 1.
• Continue until all sensors are assigned a head.
![Page 11: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/11.jpg)
Step 10
X30 Module 5: Activating Topcon Blockage
• Clicking on a head button for a sensor brings up the assignment list, in this case, sensor 1 will be on Head 1.
![Page 12: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/12.jpg)
Step 11
X30 Module 5: Activating Topcon Blockage
• After selecting a head, click on the Section tab and select the correct section.
• In this case, Sensor 1>Head 1>ICT Section 1.
• Make sure to always click the green check mark after making a selection.
![Page 13: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/13.jpg)
Step 12
X30 Module 5: Activating Topcon Blockage
• Once complete, click the running man to go back to your seeder home screens.
![Page 14: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/14.jpg)
Step 13
X30 Module 5: Activating Topcon Blockage
• Bring up your tank seeder home screen which looks similar to the picture on the right.
• Then click the small air cart icon in the left sidebar.
![Page 15: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/15.jpg)
Step 14
X30 Module 5: Activating Topcon Blockage
• A smaller window for the seeder on the left will appear like the picture indicates.
• The blockage is represented by the circular icon highlighted in the picture. Select this tab.
![Page 16: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/16.jpg)
Step 15
X30 Module 5: Activating Topcon Blockage
• You can now see 9 round divider head icons. These are your blockage sensors.
• Using the arrows in that window you can highlight a specific blockage sensor and it will tell you the number and if the blockage is wired correctly.
![Page 17: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/17.jpg)
Step 16
X30 Module 5: Activating Topcon Blockage
• When selecting a blockage sensor, a red bar filling the space represents a blockage or no flow.
• In order to activate the sensors, you have to have product flowing.
• Make sure you assign the sensors correctly.
![Page 18: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/18.jpg)
Step 1
X30 Module 5: Activating Topcon Blockage
• Begin by entering the setup menu tree by clicking the wrench icon.
![Page 19: Module 5 : Activating Topcon Blockage · X30 Module 5: Activating Topcon Blockage •A new screen will then appear with a number of blockage settings. •Settings should be selected](https://reader035.fdocuments.us/reader035/viewer/2022062602/5e9d5408a2a49a4e746bfab9/html5/thumbnails/19.jpg)