Module 3: Marking out and Hand Tools
description
Transcript of Module 3: Marking out and Hand Tools
![Page 1: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/1.jpg)
MODULE 3: M
ARKING OUT
AND HAND TOOLS
ME C H A N I C
A L WO R K S H O P
![Page 2: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/2.jpg)
MODULE OBJECTIVES
After the completion of this module, student should be able to: Identify different marking out tools and their usage. Select the appropriate tool required for marking out. Mark out work-pieces according to the dimensions given in engineering
drawings. Distinguish the different hand tools and their uses. Select the correct tool for the task. State the care and safe use of hand tools.
![Page 3: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/3.jpg)
3.4 INTRODUCTION TO HAND TOOLS
The mechanical engineer very often have to use a number of various hand tools in the course of his duties as a fitter or machinist, many of these tools are common to both.
![Page 4: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/4.jpg)
1- SPANNERS/ WRENCHES The two words “spanner” (in British English) and
“wrench” (in American English) refer to the same tool.
Spanners/Wrenches are different in shape to provide ease of operation under certain conditions.
They are manufactured from high tensile or alloy steel.
The sizes of metric spanners are identified by the distance across flats of a nut or bolt head
![Page 5: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/5.jpg)
The sizes of metric spanners are identified by the distance across flats of a nut or bolt head
S=24 mm
![Page 6: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/6.jpg)
SPANNER TYPES1-1 OPEN-ENDED SPANNERS
The ends of this type of spanners are generally oriented at an angle of 15º to the longitudinal axis of the handle to allow greater range of movement in enclosed spaces.
An open-end wrench has two different sizes; one at each end.
![Page 7: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/7.jpg)
![Page 8: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/8.jpg)
![Page 9: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/9.jpg)
1-2 RING SPANNERS
Ring spanners or box-end wrenches are recommended to be used when a better grip is needed and when the spanner swing is restricted.
![Page 10: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/10.jpg)
A box-end wrench has two different sizes; one at each end.
![Page 11: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/11.jpg)
1-3 COMBINATION SPANNERS
This type comes with an open end from one side and a ring end from the other side .
Usually both ends are having the same size
![Page 12: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/12.jpg)
1-4 ADJUSTABLE SPANNERS
Adjustable spanners are spanners that have a moving jaw to fit different bolt/nut sizes
![Page 13: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/13.jpg)
An adjustable wrench is often used where the exact size wrench is not available or when a large nut, such as a wheel spindle nut, needs to be rotated but not tightened.
Adjustable wrenches are sized by the overall length of the wrench and not by how far the jaws open.
![Page 14: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/14.jpg)
ACCIDENTS PREVENTION WHEN USING WRENCHES
When working with spanners, accidents are usually caused by the slipping of a spanner from a nut or bolt head.
In order to avoid these accidents, the following recommendations should be considered
![Page 15: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/15.jpg)
1- Use the correct size spanner for the job.2- Pull towards the body whenever possible.3- Do not obtain extra leverage by using pieces of
pipe. 4- Use a steady pull not a jerking action.5- Do not hit a spanner with a hammer.6- Make sure your hands will not strike any
obstructions.
![Page 16: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/16.jpg)
![Page 17: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/17.jpg)
TREAT ADJUSTABLE SPANNERS GENTLY
![Page 18: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/18.jpg)
2- ALLEN KEYS They are referred to as Allen keys and sometimes
Allen wrenches. Allen keys are used on grub screws and socket head
cap screws The size of Allen keys is almost like spanners
measured across flats.
Allen Keys Grub screw Socket head cap screw
![Page 19: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/19.jpg)
3- SCREWDRIVERSScrewdrivers are made in different lengths and designs,
the two most common are: Flathead/slotted
Crosshead/Phillips
![Page 20: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/20.jpg)
The flathead is identified by its length and in some cases by the blade width.
The crosshead screwdriver is identified by its point size.
![Page 21: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/21.jpg)
Always use the correct size screwdriver for the screw head; the blade should fit the width of the screw head.
![Page 22: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/22.jpg)
![Page 23: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/23.jpg)
4- PLIERSPliers are a hand tool used to hold objects firmly,
or for cutting and bending tough materials such as wires.
There are different types that can deal with different types of jobs
• Flat nose pliers • Long nose pliers • Combination pliers • Circlip pliers
![Page 24: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/24.jpg)
4-1 LONG NOSE PLIERSLong nose pliers are both cutting and gripping pliers
used by electricians and other tradesmen to bend, re-position and cut wire.
![Page 25: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/25.jpg)
4-2 COMBINATION PLIERSThese pliers incorporate side cutters, joint cutters and
pipe grip.
![Page 26: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/26.jpg)
4-3 CIRCLIP PLIERSCirclips are retaining devices They are fitted inside a groove on bores and shafts The internal circlip has to be squeezed to be removed
![Page 27: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/27.jpg)
The external circlip which is fitted onto a shaft has to be opened out to be removed
![Page 28: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/28.jpg)
The nose of the circlip plier is either straight or bent depending on the type of job.
![Page 29: Module 3: Marking out and Hand Tools](https://reader033.fdocuments.us/reader033/viewer/2022061612/568166be550346895ddac742/html5/thumbnails/29.jpg)
5- PIPE WRENCH
A pipe wrench is designed to tighten its grip on the part being rotated.
It has serrated jaws that leave marks on the part and so it might damage the surface of the part.
Accordingly, pipe wrenches must not be used to loosen a nut, unless the nut is to be replaced.