Modular Mineral Processing Plants
32
Modular Mineral Processing Plants
Transcript of Modular Mineral Processing Plants
Modular Mineral Processing Plants
Contents
Overview
- Our Philosophy
- Global Footprint
- APT as a Business Solution
- Let Your Project Fund Itself
- Artisanal Development
- No Mercury and Remediation
- Mineral Testwork Services
- Field Laboratories
- Products
Product Range
- GroundBreaker Range
- Scrubber and Wash Plant Range
- Hard Rock Crushing Range
- CIP/CIL TriTank
- Field Assay Laboratories
1
1
1
1
2
2
2
2
2
3
14
18
21
27
OverviewOUR PHILOSOPHY
APT aims to provide simple, cost effective and
efficient solutions to the mineral processing
industry. We continually strive to raise the bar,
by questioning the existing, and innovating
for improvement. Our extensive Research and
Development capability, with internal laboratory
and workshops, is ideally suited to test new
processes and deliver product designs that are
not only efficient, but simple and ergonomic.
APT’s designs are as minimalistic as possible
whilst providing an elegant, robust platform to
make the most of your project. Being modular and
pre-fabricated prior to shipping, and assembled
on site, project lead times are extremely short.
Installations through to production have been
achieved in as little as four days.
OUR GLOBAL FOOTPRINT
APT is based in Johannesburg South Africa and
is represented in 48 countries globally. More than
80 plants of all sizes have been produced to date,
with a distribution in over 25 countries. Plants
are available for alluvial, hard rock, tailings and
combinations of feed types. Processes incorporate
gravity wherever possible, but also include
flotation and cyanidation via APT’s renowned
TriTank CIP and CIL systems.
APT AS A BUSINESS SOLUTION
Mining is a business and viability is enhanced
not only by low capital, but also through ongoing
low operating costs. APT plants are amongst the
lowest cost-per-ounce available anywhere and
coupled with enhanced recoveries, high availability
and ease of operation the maximum business
advantage is assured.
LET YOUR PROJECT FUND ITSELF
The same advantages are available throughout the
APT plant range, from as little as 3tph through to
250tph capacity with logical increments in between.
The opportunity therefore exists to invest small and
grow your project through internal funding. This not
only assures a painless initiation but also lends the
opportunity to optimize and streamline as you go.
1
ARTISANAL DEVELOPMENT
APT takes the artisanal sector seriously with a
division dedicated especially to this market, called
GroundBreaker Division. Products cater to all
aspects from alluvial through to hard rock with
small combination plants also being available.
Many artisanal operations have managed to
internally grow beyond this scale and access
larger scale equipment, a testimony to APT’s
versatility. Corporate governance programmes are
also catered for where groups of artisanals are
empowered to operate efficiently and responsibly.
NO MERCURY AND REMEDIATION
APT plants do not require the use of mercury and
APT’s policy is mercury free. Even the artisanal
range is equipped with the means to get the job
done without having to resort to this toxic element.
More than just avoidance, APT manufactures plants
to specifically remediate mercury contaminated
areas, usually recovering significant quantities of
gold in the process.
MINERAL TEST WORK SERVICES
Through our ISO9001:2008 certified associated
laboratory Peacocke, Simpson and Associates,
testing is available for virtually any anticipated
process. More specifically, regimes have been
developed to test the suitability of the client’s
samples in any of the candidate APT plant types,
affording a perfect match between requirement
and solution.
FIELD LABORATORIES
Field analytical laboratories are available in a
variety of configurations to cater for geological
exploration through to CIL plant monitoring and
combination of these.
PRODUCTS
APT plants are supplied as fully comprehensive
modular solutions from ore through to gold dore,
or bagged mineral concentrates as appropriate.
The process usually begins with our famous
RG scrubber range to disintegrate loose feeds
and separate fines for gravity whilst coarse rock
proceeds to crushing and grinding. Initial gravity
recovery is achieved either through APT’s own
GoldKacha concentrator at small scale or Knelson
concentrators at large scale and jigs for the
coarser mineral separations. If gold dissolution
is required APT’s TriTank CIP or CIL options are
included, all the way through to elution and smelt.
2
GroundBreaker Range Complete Modular Start-Up & Exploration PlantsOur plants can process sand, clay & hard rock. A variety of minerals can be upgraded safely & efficiently. The modular design allows for different modules to be added to expand your plants as the need arises for you to process more, or different, material. This allows you to gain a return on investment as you expand.
GoldKacha Centrifugal Gravity Concentrator Processing System
The GoldKacha is especially suited to the recovery of precious metals from dump tailings, rubble beds & alluvial sands. It was developed especially for small mining applications. The novel centrifugal riffle
principle results in high recovery of both coarse & fine precious metals.
The GoldKacha is a simple & robust centrifugal gravity concentrator processing system. Material is slurried with water via the supplied screen. The concentrate is usually purged once every hour & requires further upgrade using equipment such as conventional panning or APT’s GoldKonka concentrate upgrader.
Several GoldKachas can be implemented as a custom treatment facility, where the owner can hire them out & enable others to process their own material in a safe & simple way.
Nesting several units also means that one operator can treat a larger tonnage of his own material.
“The simplicity of the GoldKacha makes it a very easy unit to achieve regular good percentage gold recoveries.”
Neil Greenway (Director, Greenline Services)
3
Specifications*
Model Standard
Feedrate (tph) 1-3
Nominal Feed Size (mm) 3
Installed Power (kW electric motor) 0.75
Water Requirement (m3/h) 2-4
Typical Concentrate Weight (kg) 8-10
Run Time Between Conc Washes (h) 1
Weight [Machine/Shipping] (kg) 89/109
Shipping Dimensions
Length (mm) 1210
Width (mm) 900
Height (mm) 1470
“I have used APT’s GoldKacha’s on a variety of alluvial projects in the most adverse and remote locations around the globe and they have proven themselves time again to be the ideal units for excellent recoveries in a multitude of applications. With their low operating costs and
used in conjunction with the RG 30 mobile configuration, the GoldKacha has been instrumental for assessing alluvial deposits and exploration. They are a must in any miners tool kit.”
Jason Aucamp. Mine Projects and Development Consultant (Southern Africa)
4
RG30 Scrubber Alluvial Sand & Clay Wash Plant
The RG30 Scrubber is part of our standard APT wash plant range. It is used in combination with the GoldKacha concentrator for optimal gold recovery. The plant comes fully assembled, & can be run off a small generator. The RG30 is also available in trailer version, allowing for optimized mobility. The RG30-T can be set up in just 15 minutes.
Firstly, material is fed into the RG Scrubber (by hand), where it is washed and screened before being fed into the GoldKacha. The GoldKacha then concentrates the material, and prepares it for final upgrade via the GoldKonka Concentrates Upgrader.
5
Specifications*
Model RG30/RG30-T
Concentrator GoldKacha
Throughput (tph) 2-3
Installed Power (kW) 3.5
Water Requirement (m3/h) 4
Maximum Feed Size (mm) 75
Packing Crate
Plant Footprint (m) 2.5 x 2.5
6
RDGK Hard Rock Plant Precious Mineral Liberation Solution
The RDGK Crusher is a small-scale plant that combines the RD Wet Impactor with the GoldKacha in one convenient modular package. The RDGK is portable, easy-to-operate, utilises no chemicals & only requires a water source. It has a low environmental impact with small energy & footprint requirements.
Hard rock bearing material is fed by hand into the top of the RDGK. Alternatively, a ramp can
be built to feed material directly into the feed launder where it is crushed to size and passed through to the GoldKacha. Here, the material is concentrated & prepared for final upgrade via the APT GoldKonka Concentrates Upgrader.
If rock is larger than 40mm, a small APT Jaw Crusher is used.
JC25 Jaw Crusher Plant
The JC (Jaw Crusher) range allows for hard rock material larger than 40mm to be crushed down to size. It is simple to use, & easy to relocate. The JC is powered by either electric or diesel motor.
Specifications*
Model RDGK15
Feedrate (tph) 1.5
Power Requirement (kW) 18
Water Requirement (m3/h) 2-3
Maximum Feed Size (mm) 45
Concentrate Produced (kg) 8-10
Shipping Weight (t) 1.2
Plant Dimensions
Length (mm) 1570
Width (mm) 1000
Height (mm) 2450
7
Hard rock material is fed by hand into the feed launder, where it is then crushed to size. The crushed rock is then passed through the bottom of the crusher & is ready for further crushing in the RDGK.
Specifications*
Model JC25
Throughput (tph) 2-3
Feed Opening Size (mm) 150x200
Motor Power (kW) 5.5
CSS (mm) 10-40
APT MERCURY FREE UPGRADE SOLUTIONS
GoldJigga The GoldJigga is a manual hydraulic jig used to concentrate coarse nuggets of gold from coarse (+3mm) oversize material. The material is placed in a basket with a screen base and manually jigged in a tank of water. The basket is then removed and inverted into a tray, and the coarse gold nuggets and/or gems, which have concentrated at the base of the basket, can be picked out by hand.
Specifications*
Power Supply Not Required
Basket Capacity (kg) 5-7
8
GoldKonka Mercury Free Concentrates Upgrader
The GoldKonka was designed as a mercury free solution for concentrate upgrades. It is simple to use & is able to recover the finest gold particles.
Concentrates are fed over 3 consecutive sluice trays with water & the heavy gold-bearing particles are caught on the surface of each tray. The concentrate from the trays are then washed off with water into the 2 wash basins. The material left in these basins is then smelted using the APT smelter furnace.
Several GoldKonka’s can be set up as nesting units, in the same way as the GoldKacha operation.
This allows for several people to upgrade their material more swiftly & efficiently. This method is safer to the miners & their environment. Recovery is higher & a greater profit is made.
Specifications*
Model Standard
Feedrate (kg/h) 450
Installed Power 12Volt Car Battery
Nominal Feed Size (mm) 3
Water Requirement (m3/h) 4
Shipping Dimensions
Length (mm) 1190
Width (mm) 620
Height (mm) 1030
9
The truth is, mercury is highly effective in gold recovery. What people need is not just a good mercury-free solution, but a solution that rivals its effectiveness.
APT has that solution
Mercury is not APT
“I have worked with a team to make the RD15GK into a very competent gold recovery pilot plant. The plant is highly portable and was run as a production / pilot plant. I was
able to achieve a greater through put per hour into the GK with a constant head of water and regular purging of the concentrate. The percentage recovery of gold was greater
than suggested from constant supervision of the RD15GK combo unit.”
Neil Greenway (Director, Greenline Services)
10
GoldMasta Sluice
This gold upgrade module was developed as an entry level device for artisanal miners to begin and advance production in an efficient, affordable manner. The engineering, design and rigorous test work coupled with the implementation of the latest technology has resulted maximized recoveries and the production of a higher grade concentrate. The surface matting is easy to clean, making for a quick harvest cycle. The GoldMasta is made from a durable, non-corroding material and production can be commenced as soon as it arrives on site. The GoldMasta can be relocated with ease and a power outlet is not required.
Specifications*
Feedrate Up to 1t/hr
Nominal Feed Size (mm) Max 3mm
Water Requirement 5m3/h
Shipping Dimensions
Length (mm) 1500
Width (mm) 600
Height (mm) 380
Weight (KG) Less than 23.5 (packed)
To obtain an even higher recovery, two or more GoldMasta’s can be placed in a series. This module was also engineered to go in combination with our GoldKacha concentrator, resulting in a compact package with extremely high recovery. If the full potential tonnage of the GoldKacha is required, two GoldMasta’s can be used in parallel on the tails.
11
APT Gold Smelter Fine Gold Refinery Module
The APT Gold Smelter is a small induction kettle furnace. It can be used to smelt gold recovered from the GoldKonka concentrate. It is a direct smelt system & is easy to operate.
The APT Gold Smelter comes with a kit consisting of a 220Volt smelter, gold moulds, crucible tongs, safety helmet, apron, gloves & borax (flux). This means you can smelt your gold into conical shapes for higher purity & ease of handling.
“We’ve used an RG30 Scrubber for some time now. The Scrubber breaks down tenacious clay and screens all fines to the GoldKacha Concentrator which we find extremely efficient. A winning combination, thank you APT”.
Henry Jenkins(CEO, Goldchip Investments)
12
13
RG Scrubber
Wash Plant Range Alluvial Precious & Bulk Mineral Plants
RG Scrubber Alluvial Sand & Clay Process Plants
All of APT’s scrubber plants are based on a modular design with rapid delivery & commissioning times. The modular plant philosophy allows you to start recovering minerals with a base scrubber/concentrator unit, & add modules as you progress. Various crushing, milling & other upgrade modules can be ordered to make your solution more comprehensive. This can be implemented at a later stage, once you have begun to see an initial return on investment. This way, APT provides miners with a low capital starting point. The income that these base plants generate can then be used to fund their further expansion & enhance recovery.
The plants are environmentally friendly, using no mercury or harmful chemicals. All that is required is an area to place the plant & a reliable water
source. APT solutions are designed with low energy requirements & can be run by a generator, making them independent of the grid and trans locatable.
Precious Mineral Wash Plants
The standard APT RG Scrubber is used in combination with the world renowned FLSmidth Knelson concentrator or APT’s GoldKacha for optimal gold recovery.
Firstly, material is fed into the RG Scrubber, where it is washed & screened before being pumped to the gravity concentrator. The oversize material leaves the scrubber on the discharge conveyor, & is simply discarded.
Concentrate clean-up & smelting facilities are provided in an on-site gold room, supplied by APT. These plants come pre-packaged, pre-plumbed & pre-wired, with all the necessary components needed.
These plants range from the groundbreaker size, through to large-scale placer mining operations.
14
Specifications*
Model RG30 RG100-B RG100 RG200 RG800 RG2500
Concentrator GoldKacha 2xGoldKacha
Knelson Knelson Knelson 2xKnelson
Throughput (tph) 2-3 6-10 6-10 15-20 70-80 200-250
Installed Power (kW) 3.5 20 35 68 170 365
Water Requirement (m3/h) 4 12 18 30 120 380
Max Feed Size (mm) 75 100 150 150 150 200
Packing Crate 1x40ft + 1x20ft
1x40ft + 1x20ft
x40ft + 1x20ft
2x40ft + 3x20ft + 1Break Bulk
Subject to Destination
Plant Footprint (m) 2.5x2.5 7x6 12x8 13.5x9 21x19 30x25
“The combination of the RG100 with the Knelson MD12 Concentrator is an excellent match. Even the most stubborn clays are disintegrated by the autogenous scrubbing action in the
drum section (assuming correct feed rate), and this plant combo is excellent for processing of eluvial and alluvial ores, especially smaller high value deposits.”
James Duguid (Managing Director, Stillram Mining Co.p/l)
“We have been using the RG200 Scrubber to process bauxite at our mine for 3 years. This machine has been used on a daily basis, and handles a constant feed of 15-20tph.
It successfully breaks down the tough clay content & thoroughly cleans any hard rock content within the feed material. The RG200 very successfully screens & separates our target material
(-3mm). We have had good after sales service from APT & are satisfied with the plant supplied.”
J. Meikle (Director) Mina Alumina Lda
15
Bulk Mineral Washing Plants
The RG Scrubber is not only limited to gold recovery & can be used to recover other minerals such as diamonds, bauxite & bulk minerals such as chrome, tin & tantalite. The required modules are simply added to the base scrubber to form a fully comprehensive solution.
Firstly, material is fed into the RG Scrubber, where it is washed and screened before being pumped into the required concentrator. The concentrate is then upgraded via the correct upgrade module.
Specifications*
Model RG100 RG200 RG800 RG2500
Concentrator Spirals Spirals or Knelson Knelson 2xKnelson CVD + Spirals
Throughput (tph) 6-10 15-20 70-80 200-250
Installed Power (kW) 40 76 195 372
Water Requirement (m3/h) 15 28 120 380
Max Feed Size (mm) 150 150 150 200
Packing 1x40ft + 3x20ft 3x40ft + 1x20ft 4x40ft + 3x20ftt +1Break Bulk
Subject to Destination
Plant Footprint (m) 16x1 13.5x12 21x25 30x30
16
17
Crushing Modules
Precious & Bulk Mineral Hard Rock Plants
Crusher Range Hard Rock Processing Plants
The APT range of hard rock plants is designed to provide complete, low cost process plants for clients who need optimum solutions, with low capital & start-up requirements. For optimal crushing, our hard rock range uses Jaw Crushers (JC) & RD Wet Impactors (RD), with additional processing & recovery modules simply added as required. This means you can easily alter your plant according to new mineral recovery requirements.
Our hard rock plants are designed to take you from feed ore to final marketable product & can include power generation, electrical & water systems. All plants are pre-assembled to reduce on-site installation time & commissioning delays. Larger modules are commissioned & installed by APT
professionals who also provide on-site training.
JCRD Plants Dual Jaw Crusher/Concentrator Plants
The JCRD hard rock plant range is designed for crushing & gravity recovery of minerals in clean, hard rock ore bodies. The plants use a 2-stage Jaw Crushing and RD Wet Impactor crushing circuit, followed by the required concentration modules such as a Knelson or Spirals circuit. The JC/RD combination leads to superior precious mineral liberation due to the combined impact crushing & grinding mechanisms. The RD can provide improved liberation at particle sizes coarser than a ball mill for significantly lower capital and energy requirements.
Firstly, hard rock material is fed into the grizzly, where it is separated to size. It then goes via the conveyor to the JC, where the material is then crushed to a smaller size, & passed again on a conveyor to the RD, where final crushing occurs.
18
From the RD, crushed material is fed intoa Knelson Gravity Concentrator & the crusher-liberated gold is recovered. The high quality concentrate produced is then run over the shaking table to produce a smeltable product.
As a standalone module, the JCRD crushing plants can be combined with an alluvial RG scrubbing plant to provide a complete solution for both alluvial & hard rock mineral recovery. These are referred to as “Combo” plants.
Specifications*
Model JCRD50 JCRD120 JCRD300
Concentrator Knelson Knelson Knelson
Throughput (tph) 4-5 10-12 25-30
Installed Power (kW) 70 135 355
Water Requirement (m3/h) 8 20 45
Max Feed Size (mm) 100 150 150
Packing 2x40ft + 1x20ft 2x40ft + 1x20ft 4x40ft + 2x20ft
Plant Footprint (m) 25x9 26x10 30x12
Specifications*
Model Bulk Minerals Exploration Gold Exploration CIP/CIL Monitoring
Installed Power (kVA Generator) 20 20 20
Water Requirement (l/Day) 2500 2500 2500
Plant Footprint (m) 9x9 9x9 9x9
Shipping Dimensions (ft) 2x20 2x20 2x20
Number of Samples (per day):
Soil/Rock 48
Bottle Rolls 48 48
AA Spectra 150 200
Crushing/Pulverising 48 48
Carbon (per 8 hours) 24
Gravity Gold Tests 10 10
19
“MLI Mining utilize the APT ground breaker range of equipment, the JC25, JCRD15 and MkIII and Mk IV GoldKacha concentrators. Installation, commissioning and production was achieved within 3 days of equipment arrival on site and with the assistance of APT technicians achieved full production of 30t a day within 7 days. Gold recovery was achieved on day one. Utilization of the integrated system allowed
consistent throughput with high recoveries at low costs, sufficient to give project confidence in up-scaling to the RG200 JCRD Combo plant which we hope order in the near future”
Dr Steve Newbery(CEO MLI Mining)
20
The APT TriTank Cyanidation Plant Range CIP/CIL/Carousel Modular Gold PlantsAPT Cyanidation Range
APT strive to continuously deliver the latest in mineral processing technology to our customers. As we continue to revolutionize the modular gravity recovery plant industry, APT’s technology development division has been earnestly focusing on the cyanide recovery sector for the past 4 years. Together with Peacocke & Simpson, who pioneered triangular mixing tanks in the early 80’s, APT have now patented, tested and commissioned novel triangular modular cyanide recovery units.
Leaching of gold using cyanide is the most common chemical extraction method. It is used for recovering gold in ores that are not readily treated using gravity & other physical processes. Examples include finely disseminated ores & previously treated tailings material.
The APT TriTank Modular CIP/CIL/Carousel Plants
The APT TriTank is not a cyanidation tank, it is a cyanidation system. With six reaction compartments or sectors condensed into one conventional tank, not only is the footprint smaller, but a whole host of advantages accrue to the user’s benefit. Carbon is easier to move, a sector can be easily bypassed, & most important of all, the mixing efficiency is enhanced.
The TriTank cyanidation system begins with the pre- preparation of the feed into slurry, usually in a special version of an APT RG scrubber. Dry material is accepted into the feeder & the slurrying begins to thoroughly disintegrate any agglomerates & lumps. The RG imparts an inter-particulate scrubbing action to freshen particle surfaces in the process. Organic oversize like grass, roots etc is screened out early on & the slurry is then conditioned in a holding section to remove any spikes in consistency, resulting in a smooth flow of uniform density. Next, the slurry
21
22
passes over a fine exclusion screen to remove any oversize that would otherwise contaminate the carbon. Finally, lime is added as a pH modifier to the undersize slurry before it is transported via a pipeline to the APT TriTank’s first sector. Depending upon the reaction kinetics, residence time may necessitate the slurry passing through a number of sectors to complete dissolution, after which the pregnant slurry passes into the carbon containing sectors to effect adsorption. Alternatively, if kinetics are very fast, or if preg-robbers are present, the first slurry sector may contain carbon, as per typical CIL.
One further possibility of the APT TriTank system is that the first few sectors may be used as pre-aerators and even run at elevated velocity to promote rapid oxidation. The APT TriTank’s specialised mixing action allows the use of elevated slurry densities, which may bring benefits in terms of increased capacity and also reagent strength for the same amount of cyanide addition. Carbon is removed counter current to the slurry flow with the added advantage of convenience of operation with all the sectors being adjacent to each other.
23
Specifications*
Model TT20 TT80 TT200 TT300 TT500
Total Volume (m3) 21 76 196 297 515
Solids Throughput (tph)
8h residence time 1.5 6 15 23 40
24h res time 0.5 2 5 8 13
Dimensions of a Diameter (m) 4.2 6.3 8.4 9.0 9.7
6-Sector Unit Height (m) 2.5 3.8 5.0 6.2 8.8
Installed Power (kW) 1 Unit CIL 7.5 30 55 85 110
“I would have no hesitation in recommending the APT TriTank system to anyone considering slurry cyanidation, it is a paradigm ahead of the old tank system”
Paul Mitchell (Max Mine, Zimbabwe)
24
Advantages of the TriTank System
* Stacking 6 triangular or sectorial tanks in a hexagon results in 27% less footprint than 6 circular tanks of equivalent volume (1/1 H/D ratio). That impacts not only ground space, but also on foundations, bunds, decking, cable runs & pipe runs, etc. * Common walls between tanks make for 8% less material usage than 6 equivalent tanks. * The use of a central well allows pulp flow to be directed from any sector to any sector, even from stage 1 to stage 6, without long launders. This in turn allows any sector to be taken offline for maintenance, or the plant to be operated in carousel mode. * There is no need for baffles; indeed there is nowhere to put them.
Expanding Upon Your TriTank Development
As with all APT products, the design emphases of the APT TriTank has been upon a compact, high efficiency module that can be easily & rapidly installed. Currently available in either CIP or CIL configuration at up to 515 cubic meters contained volume, the APT TriTank can be supplied as a fully comprehensive system including slurry pre-preparation, carbon elution & smelting. The TriTank complements the rest of the APT range, offering a stand-alone system for tailings retreatment or an addition onto the end of APT’s JCRD crushing-milling-gravity modules. Of particular interest is the application of APT TriTanks for intensive & aggressive cyanidation of bulk sulphide concentrates, as produced in flotation or via Knelson CVD continuous concentrator. Design is also underway upon far larger systems.
25
“We constructed two TriTanks at our eldorado mine to retreat tailings. The plant operated for 7 years and was the least problematic of any plant i have ever built and worked. We never dug out a tank. After a power cut, usually not more than 30 minutes, the plant was re started and within minutes the pulp was back in
suspension. Agitation was superb resulting in rapid dissolution and effective washing of the carbon off the horizontal carbon screens. In conclusion, the triangular agitator
is far superior to anything that has ever been built.”
John Skinner (Previously group projects manager for Lonrho.
Built three new gold plants for lonrho)
26
Field Assay Laboratories Bulk Minerals Exploration, Gold Exploration, & CIP/CIL Monitoring Containerised, Translocatable, Fully Comprehensive Field Assay Laboratories Gold Exploration, Gold Leach Plant & Non-Gold Modules
Superior Features These fully comprehensive laboratories can be relocated with ease, allowing for optimal exploration, evaluation of your mineral resource and monitoring of your mining
operation. APT supply 3 different analysis options, all of which include:
· Air conditioned container complete with sink, benches and analytical equipment. · Crushing, pulverising and other sample preparation requirements. · Compressed air, water and electrical reticulation. · Sample analytical equipment specific to the module type.
APT can provide training for operators if required.
27
Specifications*
Model Bulk Minerals Exploration Gold Exploration CIP/CIL Monitoring
Installed Power (kVA Generator) 20 20 20
Water Requirement (l/Day) 2500 2500 2500
Plant Footprint (m) 9x9 9x9 9x9
Shipping Dimensions (ft) 2x20 2x20 2x20
Number of Samples (per day):
Soil/Rock 48
Bottle Rolls 48 48
AA Spectra 150 200
Crushing/Pulverising 48 48
Carbon (per 8 hours) 24
Gravity Gold Tests 10 10
28
Modular Mineral Processing Plants
218 New Market Road, Northlands Business Park, North Riding, Randburg, South Africa
(27) 11 704 6678(27) 82 979 2277
www.aptprocessing.com
*Metallurgical performance is material dependent & prior mineral testwork is recommended by APT. Specifications subject to change without notice.
