Modification Guide CD70 NAVI
-
Upload
eduardoenriquecadenalopez -
Category
Documents
-
view
2.605 -
download
269
Transcript of Modification Guide CD70 NAVI
-
7/23/2019 Modification Guide CD70 NAVI
1/18
CD70 AUX IN Modification Guide
Page 1
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
GENERAL
STEP 1
Update your CD70 to latest firmware, i.e. 10/10/2007.
Noted that firmware updates require an update disc, this disc is different from
language disc. Normally you could request this disc from dealer or borrow
from a friend; this is a one time job anyway. Skip this step if you already got
2007 firmware.
To upgrade the firmware, simply put the update CD to NAVI slot, and follow
the instructions. This step takes about 15 minutes.
STEP 2
Find a Tech2 or vaux-com or similar product to activate your aux-in in the
software.
A new "Aux" menu will be appeared just as shown in the very last picture of
this document after a successful activation.
Audio pass is not required for this process.
Use your tech2 or vaux-com or op-com, go to EHU menu, change Code index
to 013, (Astra models please change it to 012).
STEP 3
Open your CD70 and solder some components (which are provided by this
auction) to the main board, this will require a good soldering skill.
CD70 can be easily open with a small flat (to help open the panel), a T9 and a
T10 screwdriver.
-
7/23/2019 Modification Guide CD70 NAVI
2/18
CD70 AUX IN Modification Guide
Page 2
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
STEP 4:
Connect 3 wires to the rear connector of unit, and possibly you could buy a
3.5mm stereo socket.
Jack socket is not included, can be easily sourced. e.g. Maplin, Ebay.
The wires and socket will be used for audio signal input, e.g. from your
iphone.
For example:
*3.5mm Stereo jack socket in Maplin, order code: FK03D
*Or you may purchase the tray with jack socket from dealer (very rare):
-Storage tray with jack socket PN: 13254495
-Lead for jack socket PN:13255833
-
7/23/2019 Modification Guide CD70 NAVI
3/18
CD70 AUX IN Modification Guide
Page 3
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
COMPONENT LIST
Item Quantity Reference Value
_____________________________________________________
1 2 R1, R2 470
2 2 R3, R4 56k
3 2 R5, R6 100k
4 3 C1, C2, C10 680p
5 5 C3, C4, C5, C6, C7 470n
6 2 C8, C9 100p
7 2 C11, C12 47u
8 1 U1 TDA8579
NOTE:
As a rule of thumb, do NOT leave your tip of solder iron on the pin of component for
longer than 5 seconds.
Capacitors C11, C12 are polarized. Black mark in the capacitor indicate negative (-),
and the other side is positive (+).
1uF = 1000nF
-
7/23/2019 Modification Guide CD70 NAVI
4/18
CD70 AUX IN Modification Guide
Page 4
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
FITTING GUIDE
TOOLS:
You will need:
1. A small tip solder iron, at lease 25w, preferably temperature controlled.
2. Some solder wire and flux.
3. Some small tip tweezers.
4. A T9 screwdriver.
5. A flat screwdriver.
6. Patients.
7. See point 6.
TAKE YOUR CD70 APART
STEP 1:
Make sure you get have a suitable surface to work with, and place you CD70
there.
-
7/23/2019 Modification Guide CD70 NAVI
5/18
CD70 AUX IN Modification Guide
Page 5
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
STEP 2:
Use your flat screwdriver, take off the top and bottom metal plates.
STEP 3:
Use your T9 (or T10) screwdriver, take off two copper clips.
-
7/23/2019 Modification Guide CD70 NAVI
6/18
CD70 AUX IN Modification Guide
Page 6
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
STEP 4:
Carefully take off front panel with your flat screwdriver.
STEP 5:
Undo 8 screws with T9 screwdriver and take off both Navi and CD drives. Be
careful when disconnecting the connectors.
-
7/23/2019 Modification Guide CD70 NAVI
7/18
CD70 AUX IN Modification Guide
Page 7
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
STEP 6:
With your flat screwdriver, take off the front panel. Do NOT over bend the
clips.
STEP 7:
Undo 4 T9 screws, and use flat screwdriver to withdraw the lower case.
-
7/23/2019 Modification Guide CD70 NAVI
8/18
CD70 AUX IN Modification Guide
Page 8
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
STEP 8:
Use flat screwdriver carefully prise the metal screen cover in the circuit board.
STEP 9:
Now this is what it is look like
-
7/23/2019 Modification Guide CD70 NAVI
9/18
CD70 AUX IN Modification Guide
Page 9
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
SOLDER THE COMPONENTS
Find the location to be work with, and solder the components.
Solder the parts according to following sketches.
-
7/23/2019 Modification Guide CD70 NAVI
10/18
CD70 AUX IN Modification Guide
Page 10
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
-
7/23/2019 Modification Guide CD70 NAVI
11/18
CD70 AUX IN Modification Guide
Page 11
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
-
7/23/2019 Modification Guide CD70 NAVI
12/18
CD70 AUX IN Modification Guide
Page 12
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
-
7/23/2019 Modification Guide CD70 NAVI
13/18
CD70 AUX IN Modification Guide
Page 13
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
These are what they looks like after the parts are soldered to the PCB.
-
7/23/2019 Modification Guide CD70 NAVI
14/18
CD70 AUX IN Modification Guide
Page 14
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
INSERT THE WIRE TO CONNECTOR
PIN24 AUX Left Input
PIN25AUX Right Input
PIN18AUX Signal Ground
NOTE:
Do not connect PIN18 to vehicle ground.
Most cars already have these wires in the connector.
PIN25 PIN24
PIN18
-
7/23/2019 Modification Guide CD70 NAVI
15/18
CD70 AUX IN Modification Guide
Page 15
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
HOW TO INSERT THE CRAMPS TO QUADLOCK CONNECTOR
This is typical look of Quadlock connector (left)
Fully prise the purple cramp clips on both sides.
-
7/23/2019 Modification Guide CD70 NAVI
16/18
CD70 AUX IN Modification Guide
Page 16
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
Please make sure you know which pin to insert
before continue.
Fully insert the wires with female cramp into the
quadlock connector pin housing, then refit the
purple cramp clips to the quadlock connector.
-
7/23/2019 Modification Guide CD70 NAVI
17/18
CD70 AUX IN Modification Guide
Page 17
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A GUIDE.
YYSNET MAR 2012
WIRING DIAGRAM
L R N
OR:
1824
25
-
7/23/2019 Modification Guide CD70 NAVI
18/18
CD70 AUX IN Modification Guide
Page 18
YOU TAKE YOUR OWN RISKS FOR THIS MODIFICATION! THIS IS ONLY A
GUIDE.
YYSNET MAR 2012
You could place your input socket like this (Red cycle):
Enjoy!
yysnet