MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air....

52
DATA BOOK PWFY-P200VM-E1-AU - For high temperature flow MODEL

Transcript of MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air....

Page 1: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

DATA BOOK

PWFY-P200VM-E1-AU- For high temperature flow

MODEL

Page 2: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- � -

• Donotuserefrigerantotherthanthetypeindicatedinthemanualsprovidedwiththeunitandonthenameplate.

- Do�ng so may cause the un�t or p�pes to burst, or result in explosion or fire during use, during repair, or at the time of disposal of the unit.

- It may also be in violation of applicable laws.- MITSUBISHI ELECTRIC CORPORATION cannot

be held responsible for malfunctions or accidents result�ng from the use of the wrong type of refrigerant.

• Donotusesteelpipesaswaterpipes.- Copper pipes are recommended. • Thewatercircuitshouldbeaclosedcircuit.• Askthedealeroranauthorizedtechnicianto

installtheairconditioner.- Improper �nstallat�on by the user may result �n water

leakage, electric shock, or fire.• Installtheunitinaplacethatcanwithstandits

weight.- Inadequate strength may cause the unit to fall down,

resulting in injuries.• Donottouchtheunit.Theunitsurfacecanbehot.• Donotinstalltheunitwherecorrosivegasis

generated.• Usethespecifiedcablesforwiring.Makethe

connectionssecurelysothattheoutsideforceofthecableisnotappliedtotheterminals.

- Inadequate connection and fastening may generate heat and cause a fire.

• Prepareforrainandothermoistureandearthquakesandinstalltheunitatthespecifiedplace.

- Improper �nstallat�on may cause the un�t to topple and result in injury.

• AlwaysuseanstrainerandotheraccessoriesspecifiedbyMitsubishiElectric.

- Ask an authorized technician to install the accesso-ries. Improper installation by the user may result in water leakage, electric shock, or fire.

• Neverrepairtheunit.Iftheairconditionermustberepaired,consultthedealer.

- If the unit is repaired improperly, water leakage, electric shock, or fire may result.

• DonottouchtherefrigerantpipesandWaterpipes.

- Improper handling may result in injury.• Whenhandlingthisproduct,alwayswearprotec-

tiveequipment. EG:Gloves,fullarmprotectionnamelyboilersuit,

andsafetyglasses.- Improper handling may result in injury.• Ifrefrigerantgasleaksduringinstallationwork,

ventilatetheroom.- If the refrigerant gas comes into contact with a flame,

poisonous gases will be released.• Installtheunitaccordingtothismanual.- If the unit is installed improperly, water leakage,

electric shock, or fire may result.• Haveallelectricworkdonebyalicensedelectri-

cianaccordingto“ElectricFacilityEngineeringStandard”and“InteriorWireRegulations”andtheinstructionsgiveninthismanualandalwaysuseaspecialcircuit.

- If the power source capacity is inadequate or electric work is performed improperly, electric shock and fire may result.

• Keeptheelectricpartsawayfromwater(washingwateretc.).

- It might result in electric shock, catching fire or smoke.

• Securelyinstalltheheatsourceunitterminalcover(panel).

- If the terminal cover (panel) is not installed properly, dust or water may enter the heat source unit and fire or electric shock may result.

• Wheninstallingandmovingtheairconditionertoanothersite,donotchargeitwitharefrigerantdifferentfromtherefrigerant(R410A)specifiedontheunit.

- If a different refrigerant or air is mixed with the origi-nal refr�gerant, the refr�gerant cycle may malfunct�on and the unit may be damaged.

SafetyPrecautions

Page 3: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- �� -

• Donotusetheexistingrefrigerantpiping.- The old refrigerant and refrigerant oil in the existing

p�p�ng conta�ns a large amount of chlor�ne wh�ch may cause the refrigerant oil of the new unit to dete-riorate.

- R410A is a high-pressure refrigerant and can cause the existing piping to burst.

• UserefrigerantpipingmadeofC1220(CU-DHP)phosphorusdeoxidizedcopperasspecifiedintheJISH3300“Copperandcopperalloyseamlesspipesandtubes”.Inaddition,besurethatthein-nerandoutersurfacesofthepipesarecleanandfreeofhazardoussulphur,oxides,dust/dirt,shav-ingparticles,oils,moisture,oranyothercontami-nant.

- Contaminants on the inside of the refrigerant piping may cause the refrigerant residual oil to deteriorate.

• Storethepipingtobeusedduringinstallationindoorsandkeepbothendsofthepipingsealeduntiljustbeforebrazing.(Storeelbowsandotherjointsinaplasticbag.)

- If dust, dirt, or water enters the refrigerant cycle, deterioration of the oil and compressor trouble may result.

• Applyasmallamountofesteroil,etheroil,oralkylbenzenetoflares.(forindoorunit)

- Infiltration of a large amount of mineral oil may cause the refrigerant oil to deteriorate.

• Useliquidrefrigeranttofillthesystem.- If gas refrigerant is used to seal the system, the

composition of the refrigerant in the cylinder will change and performance may drop.

• DonotusearefrigerantotherthanR410A.- If another refrigerant (R22, etc.) is mixed with

R410A, the chlor�ne �n the refr�gerant may cause the refrigerant oil to deteriorate.

• Useavacuumpumpwithareverseflowcheckvalve.

- The vacuum pump oil may flow back into the refrig-erant cycle and cause the refrigerant oil to deterio-rate.

• Donotusethefollowingtoolsthatareusedwithconventionalrefrigerants.

(Gaugemanifold,chargehose,gasleakdetector,reverseflowcheckvalve,refrigerantchargebase,refrigerantrecoveryequipment)

- If the conventional refrigerant and refrigerant oil are mixed in the R410A, the refrigerant may deterio-rated.

- If water is mixed in the R410A, the refrigerant oil may deteriorate.

- Since R410A does not contain any chlorine, gas leak detectors for conventional refrigerants will not react to it.

• Donotuseachargingcylinder.- Using a charging cylinder may cause the refrigerant

to deteriorate.• Donotuseantioxidantorleak-detectionadditive.• Beespeciallycarefulwhenmanagingthetools.- If dust, dirt, or water gets in the refrigerant cycle, the

refrigerant may deteriorate.

• Iftheairconditionerisinstalledinasmallroom,measuresmustbetakentopreventtherefriger-antconcentrationfromexceedingthesafetylimiteveniftherefrigerantshouldleak.

- Consult the dealer regarding the appropriate meas-ures to prevent the safety limit from being exceeded. Should the refrigerant leak and cause the safety limit to be exceeded, hazards due to lack of oxygen in the room could result.

• Whenmovingandreinstallingtheairconditioner,consultthedealeroranauthorizedtechnician.

- If the air conditioner is installed improperly, water leakage, electric shock, or fire may result.

• Aftercompletinginstallationwork,makesurethatrefrigerantgasisnotleaking.

- If the refrigerant gas leaks and is exposed to a fan heater, stove, oven, or other heat source, �t may gen-erate noxious gases.

• Donotreconstructorchangethesettingsoftheprotectiondevices.

- If the pressure sw�tch, thermal sw�tch, or other protection device is shorted and operated forcibly, or parts other than those specified by Mitsubishi Electric are used, fire or explosion may result.

• Todisposeofthisproduct,consultyourdealer.• Theinstallerandsystemspecialistshallsecure

safetyagainstleakageaccordingtolocalregula-tionorstandards.

- Following standards may be applicable if local regu-lation are not available.

• Payaspecialattentiontotheplace,suchasabasement,etc.whererefrigerationgascanstay,sincerefrigerationisheavierthantheair.

Page 4: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- ��� -

• Donotinstalltheunitwherecombustiblegasmayleak.

- If the gas leaks and accumulates around the unit, an explosion may result.

• Donotusetheairconditionerwherefood,pets,plants,precisioninstruments,orartworkarekept.

- The quality of the food, etc. may deteriorate.• Donotusetheairconditionerinspecialenviron-

ments.- Oil, steam, sulfuric smoke, etc. can significantly reduce

the performance of the air conditioner or damage its parts.

• Wheninstallingtheunitinahospital,communica-tionstation,orsimilarplace,providesufficientprotectionagainstnoise.

- The inverter equipment, private power generator, high-frequency medical equipment, or radio commu-nication equipment may cause the air conditioner to operate erroneously, or fail to operate. On the other hand, the air conditioner may affect such equipment by creating noise that disturbs medical treatment or image broadcasting.

• Donotinstalltheunitonastructurethatmaycauseleakage.

- When the room humidity exceeds 80 % or when the drain pipe is clogged, condensation may drip from the indoor unit. Perform collective drainage work together with the unit, as required.

Page 5: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- �v -

• Groundtheunit.- Do not connect the ground wire to gas or water

pipes, lightning rods, or telephone ground lines. Improper grounding may result in electric shock.

• Installthepowercablesothattensionisnotappliedtothecable.

- Tension may cause the cable to break and generate heat and cause a fire.

• Installaleakcircuitbreaker,asrequired.- If a leak circuit breaker is not installed, electric shock

may result.• Usepowerlinecablesofsufficientcurrent

carryingcapacityandrating.- Cables that are too small may leak, generate heat,

and cause a fire.• Useonlyacircuitbreakerandfuseofthe

specifiedcapacity.- A fuse or c�rcu�t breaker of a larger capac�ty or a

steel or copper w�re may result �n a general un�t failure or fire.

• Donotwashtheairconditionerunits.- Washing them may cause an electric shock.• Becarefulthattheinstallationbaseisnot

damagedbylonguse.- If the damage is left uncorrected, the unit may fall

and cause personal injury or damage property.• Installthedrainpipingaccordingtothismanualto

ensureproperdrainage.Wrapthermalinsulationaroundthepipestopreventcondensation.

- Improper drain piping may cause water leakage and damage to furniture and other possessions.

• Beverycarefulaboutproducttransportation.- If the un�t we�ghs more than 20kg, carry the un�t w�th

more than one person.- Some products use PP bands for packaging. Do not

use any PP bands for a means of transportation. It is dangerous.

- When transporting the unit, support it at the specified positions on the unit base. Also support the unit at four points so that it cannot slip side ways.

• Safelydisposeofthepackingmaterials.- Packing materials, such as nails and other metal or

wooden parts, may cause stabs or other injuries.- Tear apart and throw away plastic packaging bags

so that it is out of reach of children. If children play w�th a plast�c bag wh�ch was not torn apart, they face the risk of suffocation.

Page 6: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- v -

• Turnonthepoweratleast12hoursbeforestartingoperation.

- Starting operation immediately after turning on the main power switch can result in severe damage to internal parts. Keep the power switch turned on during the operational season.

• Donottouchtheswitcheswithwetfingers.- Touching a switch with wet fingers can cause elec-

tric shock.• Donottouchtherefrigerantpipesduringandim-

mediatelyafteroperation.- During and immediately after operation, the

refrigerant pipes are may be hot and may be cold, depending on the condition of the refrigerant flowing through the refrigerant piping, compressor, and other refrigerant cycle parts. Your hands may suffer burns or frostbite if you touch the refrigerant pipes.

• Donotoperatetheairconditionerwiththepanelsandguardsremoved.

- Rotat�ng, hot, or h�gh-voltage parts can cause injuries.

• Donotturnoffthepowerimmediatelyafterstoppingoperation.

- Always wait at least five minutes before turning off the power. Otherwise, water leakage and trouble may occur.

• Donottouchthesurfaceofthecompressorduringservicing.

- If unit is connected to the supply and not running, crank case heater at compressor is operating.

• Donottouchthepanelsnearthefanoutletwithbarehands:theycangethotwhiletheunitisinoperation(evenifitisstopped)orimmediatelyafteroperationtopreventburns.Wearglovestoprotectyourhandswhenitisnecessarytotouchthepanels.

• Whiletheunitisinoperationorimmediatelyafteroperation,high-temperatureexhaustairmayblowoutofthefanexhaustoutlet.Donotholdyourhandsovertheoutletortouchthepanelsneartheoutlet.

• Besuretoprovideapathwayfortheexhaustairfromthefan.

• Waterpipescangetveryhot,dependingonthepresettemperature.Wrapthewaterpipeswithinsulatingmaterialstopreventburns.

Page 7: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

ContentsSafetyPrecautions

I GeneralEquipmentDescriptions

1. Unit configuration table ················································· 12. Operable temperature range ······································· 13. Setting of Dip switch······················································ 1

II ProductSpecifications1. Specifications ································································· 2

(1) PWFY-P200VM-E1-AU (for h�gh temperature flow)2. External Dimensions ····················································· 3

(1) PWFY-P200VM-E1-AU(2) PUHY-P300YJM-A(-BS)(3) PQHY-P300YHM-A

3. Electrical Wiring Diagrams ··········································· 6(1) PWFY-P200VM-E1-AU(2) PUHY-P300YJM-A(-BS)(3) PQHY-P300YHM-A

4. Accessories ····································································· 9(1) PWFY

III ProductData1. Capacity tables·····························································10

(1) Correction by temperature (Estimated performance without defrost)

(2) Correct�on by water flow rate(3) Correction at frosting and defrosting(4) Water pressure drop(5) Operat�on temperature range

2. Sound pressure levels ················································18(1) PWFY-P200VM-E1-AU

3. Refrigerant circuit diagrams and thermal sensors ···18(1) PWFY-P200VM-E1-AU

IV Installation1. How to calculate the necessary heating capacity ·· 19

(1) Heat�ng capac�ty calculat�on(2) Calculat�on example

2. Installation ·····································································20(1) Select�ng an �nstallat�on s�te (for PWFY unit)(2) Install�ng the un�t(3) Refrigerant pipe and drain pipe specifications(4) Connecting refrigerant pipes and drain pipes

3. Water pipe installation················································· 27(1) Water c�rcu�t sample(2) Select�ng a water pump(3) Install�ng the stra�ner(4) Precautions during installation(5) Example of un�t �nstallat�on(6) Insulat�on �nstallat�on(7) Flow sw�tch �nstallat�on(8) Water processing and water quality control(9) Br�ne(10) Pump �nterlock(11) Anti freeze mode (Dip SW4-4 ON)

V SystemDesign1. Electrical work ······························································34

(1) General caut�ons(2) Power supply for PWFY unit(3) Connecting remote controller, indoor and outdoor

transm�ss�on cables(4) Transm�ss�on cable spec�f�cat�ons(5) Connect�ng electr�cal connect�ons(6) Indoor unit address setting(7) External �nput/output funct�on

VI Controller1. PAR-W21MAA specifications····································· 402. Dip switch functions ···················································· 41

VIIMaintenanceCycle1. Routine maintenance checks ···································· 422. Parts Replacement Cycle··········································· 42

Page 8: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 1 -

1.Unitconfigurationtable

Model NameATW un�t PWFY-P200VM-E1-AUOutdoor unit(Heat source un�t)

PUHY-P300YJM-A PQHY-P300YHM-A

2.OperabletemperaturerangePWFY

Cool�ng Heat�ngInlet water temperature 10 to 35ºC 10 to 54ºCOutdoor temperature Y series -5 to 46ºCDB -5 to 15.5ºCWB *1C�rculat�ng water temperature WY series 10 to 45ºC 10 to 45ºC

*1. Temp. range for high-temperature specifications. When the outdoor temperature is between -20ºC(-4 ºF)W.B.

and -5ºC(23 ºF)W.B., the inlet water temperature range will be between 10ºC(50 ºF) and 40ºC(104 ºF).

3.SettingofDipswitch<Outdoor unit (Heat source unit)>D�p SW 3-7 OFF, D�p SW 4-7 ON

<ATW unit>Dip SW 1-6 ON, Dip SW 3-8 ON

GeneralEquipmentDescriptions I

Page 9: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 2 -

1.Specifications(1) PWFY-P200VM-E1-AU (for high temperature flow)

ProductSpecifications II

Model

Power sourcekW*1Heating capacitykcal / hBTU / hkWkcal / hBTU / h

*1*1

kW

-

Inlet Water temp.-

*2

Cooling capacity-kWkcal / hBTU / hkW

*2

(Nominal)

*2

*4

*3*3*3

Power inputCurrent input A

--

dB<A>mm(in.)mm(in.)mm(in.)mm(in.)mm(in.)mm(in.)

mmExternal finishExternal dimension H × W × D

in. kg(lbs)Net weight

Circulating waterRange

Design pressureWaterR410A

Drawing

Standard attachment

Optional partsRemark

Note:

InletOutlet

Operation Volume

LiquidGas

m3/h

MPaMPa

Accessory

ExternalWiringDocument

Unit converter

*2 Hi-temp flow Heating conditions

*1 Nominal heating conditions

Outdoor Temp. : 7°CDB/6°CWB (45°FDB / 43°FWB)

Outdoor Temp. : -3°CWB (27°F)Pipe length : 7.5m (24-9/16ft)

Pipe length : 7.5m (24-9/16ft)

Level difference : 0m (0ft)

Level difference : 0m (0ft)Inlet water Temp 30°C Water flow rate 4.30m3/h Inlet water Temp 30°C Water flow rate 4.30m3/h

Inlet water Temp 45°C Water flow rate 2.50m3/h

Water flow rate 3.86m3/h

Inlet water Temp 45°C Water flow rate 2.50m3/h

* Due to continuing improvement, the above specifications may be subject to change without notice.* The unit is not designed for outside installations.* Please don't use the steel material for the water piping material.* Please always make water circulate or add the brine to the circulation water when the ambient temperature becomes 0°C or less.* Please always make water circulate or pull out the circulation water completely when not using it.* Please do not use groundwater and well water.* Install the unit in an environment where the wet bulb Temp. will not exceed 32°C. * The water circuit must use the closed circuit.* Please do not use it as a drinking water.

Details on foundation work, duct work, insulation work, electrical wiring, power source switch, and other items shall be referred to the Installation Manual.

10~45°C (50~113°F)

25.0 / 22.521,500 / 19,40085,300 / 76,800

21,50085,300

0.015

E94C228X01

NONE

Ø32 (1-1/4'')

PWFY-P200VM-E1-AU (for high temperature flow)1-phase 220-230-240V 50/60Hz

10~54°C (50~131°F)-5~45°C (23~113°F)

29

25.0

1.8~4.30

1.00

Strainer, Connecter, Heat insulation material, 2 × Connector sets, Expansion joint, wire, Flow switch × 1set

PT 1 Screw

Installation Manual, Instruction Book

NO

WKB94L763

31-1/2" (30-15/16" without legs) × 17-3/4” × 11-13/16”38 (84)

800 (785 without legs) × 450 × 300

4.15

19,300

Ø19.05 (Ø3/4") Brazed

Ø19.05 (Rc3/4") Brazed

Ø9.52 (Ø3/8") Brazed

PT 1 Screw

76,400

22.4

-5~45°C (23~113°F)10~35°C (50~95°F)

PUHY-P300YJM-A(-BS) / PQHY-P300YHM-A

0.0150.068 - 0.065 - 0.063

kcal = kW × 860BTU/h= kW × 3,412cfm = m3/min × 35.31lbs = kg / 0.4536* The specification data is subject to rounding variation.

AW.B

0.068 - 0.065 - 0.063-5~15.5°C (23~60°F)

D.B-

-5~46°C (23~115°F) 10~45°C (50~113°F)

<PUHY-series>

<PUHY-series>

*3 Nominal cooling conditions

*4 Temp. range for high-temperature specifications. When the outdoor temperature is between -20ºC(-4 ºF)W.B. and -5ºC(23 ºF)W.B., the inlet water temperature range will be between 10ºC(50 ºF) and 40ºC(104 ºF).

Outdoor Temp. : 35°CDB (95°FDB)Pipe length : 7.5m (24-9/16ft)Level difference : 0m (0ft)Inlet water Temp 23°C

<PUHY-series>

Circulating water Temp. : 20°C (68°F) Pipe length : 7.5m (24-9/16ft)Level difference : 0m (0ft)

brain connection 0%

brain connection 0%

<PQHY-series>

<PQHY-series>Circulating water Temp. : 2°C (36°F)Pipe length : 7.5m (24-9/16ft)Level difference : 0m (0ft)

Inlet water Temp 23°C Water flow rate 3.86m3/hbrain connection 0%

<PQHY-series>Circulating water Temp. : 30°C (86°F)Pipe length : 7.5m (24-9/16ft)Level difference : 0m (0ft)

Temp.range ofheating

Heatsourcerange

Nominal

High temp. flow Heating(PUHY/PQHY)

Power inputCurrent input

PUHY - seriesPQHY - seriesPQHY - series (for ground source)

PWFY range

Temp.range ofheating

Heatsourcerange

PUHY - seriesPQHY - seriesPQHY - series (for ground source)

PWFY range

Outdoor temp.Circulating water temp.Circulating brine temp.

Inlet Water temp.

Outdoor temp.Circulating water temp.Circulating brine temp.

Diameter of refrigerant pipe

Diameter of water pipe

Sound pressure level (measured in anechoic room)

Strainer sizeField drain pipe size

Connectable outdoor unit/heat source unit

Page 10: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 3 -

2.ExternalDimensions(1) PWFY-P200VM-E1-AU

300 600

Fig.

A

Ser

v�ce

spa

ce(fr

ont s

ide)

Top

v�ew

400

P�p

�ng

spac

e(r

ight

sid

e)P

200:

Use

the

Exp

ans�

on jo

�nt

o

f acc

esso

r�es

Dra

�n (R

1 sc

rew

)

ø9.5

2 <B

raze

d>

ø27

Kno

ckou

t hol

e<H

ole

for c

ontro

l w�r�

ng>

ø27

Kno

ckou

t hol

e<H

ole

for p

ower

sup

ply>

Wat

er o

utle

t(R

C3/

4 sc

rew

)

Wat

er �n

let

(R3/

4 sc

rew

)

P20

0:ø1

9.05

<B

raze

d>

ø27

Kno

ckou

t hol

e<H

ole

for e

xter

nal w

iring

inpu

t>ø2

7 K

nock

out h

ole

<Hol

e fo

r ext

erna

l w�r�

ng o

utpu

t>

Con

nect

ion

pipe

of o

utdo

or u

nit

(Gas

)

Con

nect

ion

pipe

of o

utdo

or u

nit

(Liq

uid)

Fron

t v�e

wR

ight

sid

e vi

ew

Con

trol b

ox

Ser

v�ce

pan

el

Top

v�ew

2X2-

ø14

Hol

e

525

( Mou

nt�n

g p�

tch)

450

(Mount�ng p�tch)300 800

205

500

<Acc

esso

ries>

●Y-ty

pe s

tra�n

er (R

C3/

4) ··

······

······

······

······

··· 1

pc.

●Wire

·····

······

······

······

······

······

······

······

······

·····

1pc.

●Flo

w s

witc

h ···

······

······

······

······

······

······

······

·· 1s

et

●Hea

t Ins

ulat

ion

mat

eria

l ····

······

······

······

······

1pc

.●C

onne

ctor

set

·····

······

······

······

······

······

······

··· 2

set

●Exp

ansi

on jo

int (

P20

0) ··

······

······

······

······

···· 2

pcs.

[F

rom

RC

3/4

to R

C1]

Not

e 1.

Ens

ure

no ra

in w

ater

or d

ebris

can

ent

er th

e un

it th

roug

h an

y ga

ps a

roun

d

w

iring

or p

ipin

g.

2.E

nsur

e ad

equa

te s

ervi

ce s

pace

is ri

ght a

roun

d th

e un

it, a

ccor

ding

to F

ig A

.

3.P

leas

e al

way

s m

ake

wat

er c

ircul

ate

or a

dd th

e br

ine

to th

e ci

rcul

atio

n w

ater

w

hen

the

amb�

ent t

empe

ratu

re b

ecom

es 0

°C o

r les

s.

4.T

he u

nit i

s no

t des

igne

d fo

r out

side

inst

alla

tions

.

5.In

stal

l the

uni

t in

an e

nviro

nmen

t whe

re th

e w

et b

ulb

Tem

p.

will

not

exc

eed

32de

gC.

6

.Ple

ase

alw

ays

mak

e w

ater

circ

ulat

e or

pul

l out

the

circ

ulat

ion

wat

er c

ompl

etel

y w

hen

not u

sing

it.

7

.The

wat

er c

ircui

t mus

t use

the

clos

ed c

ircui

t.

8.P

leas

e do

n't u

se th

e st

eel m

ater

ial f

or th

e w

ater

pip

ing

mat

eria

l.

9.C

onne

ct th

e st

rain

er w

hich

is p

ut a

s ac

cess

ory

to w

ater

inle

t pip

e.

9191

35 5535

480 102

206

134

114

100 1914660 140 80 165

54

<Uni

t:mm

>

Page 11: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 4 -

(2) PUHY-P300YJM-A(-BS)

For t

rans

miss

ion ca

bles

For w

ires

For p

ipes

Spe

cific

atio

nsU

sage

NO.

<Acc

esso

ries>

Conn

ectin

g pip

e

<Gas

>•E

lbow(

IDø2

5.4X

ODø2

5.4)

······

·P30

0•P

ipe (I

Dø25

.4XO

Dø22

.2)··

······

P300

Note

1.Pl

ease

refe

r to

the

insta

llatio

n m

anua

l for i

nfor

mat

ionre

gard

ing n

eces

sary

spac

ing a

roun

d th

e un

it and

fo

unda

tion

work

.2.

The

deta

chab

le leg

can

be re

mov

ed a

t site

.At

bra

zing

of p

ipes,w

rap

the

refri

gera

nt se

rvice

valve

with

wet

clot

h an

d ke

ep th

e te

mpe

ratu

re o

fre

frige

rant

serv

ice va

lve u

nder

120

°C

3.

1pc.

1pc.

<Liqu

id>•P

ipe (I

Dø12

.7XO

Dø12

.7)··

······

P300

•Pipe

(IDø

12.7

XODø

9.52

)·····

···P3

001p

c.1p

c.

1 2 3 4 5 6

Fron

t thro

ugh h

oleBo

ttom

throu

gh ho

leFr

ont th

roug

h hole

Fron

t thro

ugh h

oleBo

ttom

throu

gh ho

leFr

ont th

roug

h hole

102X

72 K

nock

out h

ole15

0X92

Kno

ckou

t hole

ø65

or ø

40 K

nock

out h

oleø5

2 or

ø27

Kno

ckou

t hole

ø52

Knoc

kout

hole

ø34

Knoc

kout

hole

2X5-

ø4.6

Hol

e(M

ake

hole

at t

he p

last

ic fa

n gu

ard

for s

now

hoo

d at

tach

men

t)

150 150 150 150 80

1888

418

760

920

<Sno

w h

ood

atta

chm

ent h

ole>

Top

view

1710

14101650

240

Inta

keai

r

Ser

vice

pane

l

Con

trol b

ox

Inta

keai

r

(60)

72 90

102

9820

425

1

13288

2X2-

14X

20 O

val h

ole

(fron

t and

bac

k,2

poin

ts)

Not

e 2*

Det

acha

ble

leg

64 3

1

Fron

t vie

w22

115

083

251

186

145

760

1818

86

8080

92

Ref

riger

ant s

ervi

ce

valv

e <g

as>

52

131C

Refri

gera

nt s

ervic

eva

lve <

liqui

d>

(Mou

ntin

g pi

tch)

Bot

tom

vie

w

(Mounting pitch)(760)

724(721~727)

Dis

char

ge a

ir

Inta

keai

r

Ref

riger

ant s

ervi

ceva

lve

<gas

>

Ref

riger

ant s

ervi

ce

valv

e <l

iqui

d>

A

B (60)

556025

760

255560

54

Left

side

vie

wC

onne

ctin

g pi

pe s

peci

ficat

ions

150C

172

143

BA

Gas

Liqu

id

PUHY

-P30

0YJM

Mod

el

Pos

ition

dim

ensi

ons

for t

he re

frige

rant

serv

ice

valv

eC

onne

ctio

n sp

ecifi

catio

ns fo

rth

e re

frige

rant

ser

vice

val

ve*1

Gas

Liqu

id

ø22.

2 Br

azed

ø9.5

2 Br

azed

(ø12

.7 Br

azed

)*2 *3

*1 C

onne

ct by

usin

g th

e co

nnec

ting

pipes

(for

bot

tom

pipi

ng a

nd fr

ont p

iping

)

that

are

supp

lied.

*2 In

dicat

es d

imen

sions

and

conn

ectio

n sp

ecific

ation

s in

the

case

the

unit i

s

use

d in

com

binat

ion w

ith o

ther

out

door

unit

s.*3

Tota

l leng

th>=

40m

Unit : mm

Page 12: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 5 -

(3) PQHY-P300YHM-A

Ser

vice

spa

ce(fr

ont s

ide)

Servi

ce sp

ace

(fron

t sid

e)

Top

view

550

6060

20

74

1160(60)

The

spac

e fo

rco

ntro

l box

repl

acem

ent

450

600

170

350 72

5

600450

170

1100550 (530)

(102

)(5

3)

506 (503~509)

470 (467~473)

834

720

1100

141213240

2 x

2-14

x 2

0 O

val h

ole

14075

608

563

584

83 58

121226234

18

78 168

433 54

8

(550)2222

4040

550

880

2 x

2-14

x 2

0 O

val h

ole

(Inst

alla

tion

supp

ort h

ole)

(880

)

8080 23

23

Con

trol b

ox

Ser

vice

pane

l

(Inst

alla

tion

supp

ort h

ole

pitc

h) (M

ount

ing

pitc

h)

(Installation support hole pitch)

(Mounting pitch)

78

6543

2

Refri

gera

nt s

ervic

e va

lve

<Gas

>

Refri

gera

nt s

ervic

e va

lve

<Liq

uid>

1

(fron

t and

bac

k, 2

poi

nts)

Not

e 8*

Det

acha

ble

leg

880

ø22.

2 Br

azed

ø9.5

2 B

raze

d

Gas

Liqu

id

PQ

HY-

P30

0YH

M-A

*1*1

Fig.

BFi

g. A

Not

e 1.

Clo

se a

hol

e of

the

wat

er p

ipin

g, th

e re

frige

rant

pip

ing,

th

e po

wer

sup

ply,

and

the

cont

rol w

iring

and

unu

sed

knoc

kout

h

oles

with

the

putty

etc

. so

as n

ot to

infil

trate

rain

wat

er

etc

. (fie

ld e

rect

ion

wor

k)N

ote

2. A

t the

tim

e of

pro

duct

shi

pmen

t, th

e fro

nt s

ide

pipi

ng

spe

cific

atio

n se

rves

as

the

loca

l dra

inag

e co

nnec

tion.

W

hen

conn

ectin

g on

the

rear

sid

e, p

leas

e re

mov

e th

e

rear

sid

e pl

ug s

ealin

g co

rks,

and

atta

ch a

fron

t sid

e.

Ens

ure

ther

e is

no

leak

afte

r the

atta

chm

ent h

as b

een

fitte

d.N

ote

3. T

ake

notic

e of

ser

vice

spa

ce a

s Fi

g. A

. (In

cas

e of

sin

gle

in

stal

latio

n, 6

00m

m o

r mor

e of

bac

k sp

ace

as fr

ont s

pace

m

akes

eas

ier a

cces

s w

hen

serv

icin

g th

e un

it fro

m re

ar s

ide)

Not

e 4.

If w

ater

pip

es o

r ref

riger

ant p

ipes

stre

tch

upw

ard,

re

quire

d sp

ace

for s

ervi

ce a

nd m

aint

enan

ce d

ue to

repl

acem

ent o

f con

trol b

ox is

sho

wn

in F

ig. B

.N

ote

5. E

nviro

nmen

tal c

ondi

tion

for i

nsta

llatio

n; -2

0~40

°C (D

B)

a

s in

door

inst

alla

tion.

Not

e 6.

In c

ase

the

tem

pera

ture

aro

und

the

heat

sou

rce

unit

has

p

ossi

bilit

y to

dro

p un

der 0

°C, b

e ca

refu

l for

the

follo

win

g

poi

nt to

pre

vent

the

pipe

bur

st b

y th

e w

ater

pip

e fre

eze-

up.

·

Circ

ulat

e th

e w

ater

all

the

time

even

if th

e he

at s

ourc

e

un

it is

not

in o

pera

tion.

·

Dra

in th

e w

ater

from

insi

de o

f the

hea

t sou

rce

unit

whe

n

th

e he

at s

ourc

e un

it w

ill n

ot o

pera

te fo

r a lo

ng te

rm.

Not

e 7.

Ens

ure

that

the

drai

n pi

ping

is d

ownw

ard

with

a p

itch

of

m

ore

than

1/1

00.

Not

e 8.

The

det

acha

ble

leg

can

be re

mov

ed a

t site

.N

ote

9. A

t bra

zing

of p

ipes

, wra

p th

e re

frige

rant

ser

vice

val

ve

w

ith w

et c

loth

and

kee

p th

e te

mpe

ratu

re o

f

refri

gera

nt s

ervi

ce v

alve

und

er 1

20°C

.

140

x 77

Knoc

kout

hole

ø34

Kno

ckou

t hol

eø5

2 or ø

27 K

nock

out h

ole

For p

ipes

For w

ires

For t

rans

miss

ion ca

bles

Fron

t thr

ough

hol

eFr

ont t

hrou

gh h

ole

Fron

t thr

ough

hol

e

Spe

cific

atio

ns

ø65 o

r ø40

Kno

ckou

t hole

Fron

t thr

ough

hol

e

Wat

er p

ipe

Dra

in p

ipe

inle

tou

tlet

Rc1

-1/2

Scr

ewR

c1-1

/2 S

crew

Rc3

/4 S

crew

Usa

geC

onne

ctio

n sp

ecifi

catio

ns fo

rth

e re

frige

rant

ser

vice

val

veM

odel

Con

nect

ing

pipe

spe

cific

atio

ns

*1. C

onne

ct b

y us

ing

the

conn

ectin

g pi

pes

that

are

sup

plie

d.

<Acc

esso

ries>

· Ref

riger

ant (

Liqu

id) c

onn.

pip

e ···

··1 p

c.(P

300

; Pac

kage

d in

the

acce

ssor

y ki

t)· R

efrig

eran

t (G

as) c

onn.

pip

e ···

··1 p

c.

· Wat

er s

topp

er (L

arge

, Sm

all)

·····1

pc.

eac

h· S

ealin

g m

ater

ial (

Long

, Sho

rt) ··

···1

pc. e

ach

(P30

0 ; P

acka

ged

in th

e ac

cess

ory

kit)

Unit : mm

NO

.

Page 13: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 6 -

3.ElectricalWiringDiagrams(1) PWFY-P200VM-E1-AU

gray

red

M

For o

pen�

ng/c

los�

ng th

e by

pass

c�rc

u�t

Sol

enoi

d va

lve

SV

1

TB5

M1M2

S(SH

IELD)

To o

utdo

or u

nit

4-20

mA

4-20

mA

13

2C

N42

1bl

ack

13

2C

N42

2bl

ue1

32

CN

422

blue

2bl

ack

CN

421

13

IN1

2345

yello

w/g

reen

LEV1

Wa

LEV1

Wb

L�ne

arex

pans

�on

valv

eB

C c

ontro

ller/W

CB

/out

door

uni

tB

C c

ontro

ller/W

CB

/out

door

uni

t

Func

t�on

Func

t�on

Func

t�on

blac

kye

llow

purp

lebl

uere

d

NL

IN7IN

8IN

6IN

5CO

M+IN

4IN

3

oran

ge

*3.D

iffer

ence

of a

ppl�a

nce

*4 T

B14

1A(o

utpu

t)

*5 T

B14

2A(�n

put)

*6 T

B14

2B(�n

put)

*7 T

B14

2C(�n

put)

Mod

el n

ame

App

l�anc

eP

200

*3 e

xist

*7*6

*5

*4

Coo

l�ng

TH23

gas

p�pe

tem

p

CN50

2bla

ck

COM+

TH8

TH6

TH23

t°t°t°

blue

CN

2M2121

CN

402

gree

n

21C

N40

3re

d

1 2C

N40

4bl

ack

yello

wC

N40

5t°

TH22

1 2

21 To

MA

rem

ote

cont

rolle

rP

ower

Sup

ply

~220

/230

/240

V50

Hz/

60H

z

Unit a

ddre

ss se

tting(

SWU1

,SW

U2)

Conn

ectio

n No

.(SW

U3)

LED

1

TB15

ZNR

1

UD

SA

1

CN

11 3

SWU2

SWU1

SWP3

SWP2

SWP1

OFF

ON

110

SW

4OF

FON

110

SW

3

OFF

ON

110

SW

1

OFF

ON

110

SW

2LE

D4:

Rem

ote

cont

rolle

r

whe

n po

wer

ed5

CN

LVC

6 1

LEV1

Wb

1234

X50

2

CN50

7

31

M56

ON OFF 1S

W5

SWU3

LED

3:Li

t whe

n po

wer

ed

Con

trol B

oard

CN

LVB

LEV1

Wa

TB2

SV1

*3

DS

A B

oard

CN

3Tre

d13

T01

ZNR

01

31

12

CNAC

red

U

F01

AC25

0V6.

3A

LED1

D�sp

lay se

tt�ng(

SW2)

Func

t�on

sett�n

g(SW

1,SW

3,SW

4)

OUT4

OUT3

OUT2

X514

X513

X512

TB14

1A

OUT1

X511

31

CN

3Abl

ue

TB14

2CTB

142B

X516

X517

X515

OUT6

OUT7

OUT5

TB14

1B

TB14

2A

IN2

IN8

IN7

Ant

�-fre

eze

IN6

Hea

t�ng

EC

O

Sym

bol

CO

M+

Com

mon

IN5

Hea

t�ng

IN4

Ope

rat�o

n O

N/O

FFC

onne

ctio

n de

man

dS

ymbo

lIN

3

Sym

bol

Flow

sw

�tch

IN1

Func

t�on

Sym

bol

OU

T1O

pera

t�on

ON

/OFF

OU

T2D

efro

stO

UT4

Err

or s

�gna

l

<CA

UTI

ON

FO

R IN

STA

LLAT

ION

> ·P

rior t

o in

stal

latio

n,re

ad th

e In

stal

latio

n M

anua

l car

eful

ly.*1

.Sin

gle-

dotte

d lin

es in

dica

te w

iring

not

sup

plie

d wi

th th

e un

it.*2

.Dot

-das

h lin

es in

dica

te th

e co

ntro

l box

bou

ndar

ies.

TH8

wat

er o

utle

t tem

pTH

6w

ater

�nle

t tem

p

TH22

liqui

d pi

pe te

mp

Ther

m�s

tor

TB15

MA

rem

ote

cont

rolle

rTB

5O

utdo

or u

nit/W

CB

/BC

con

trolle

rTB

2

Exp

lana

t�on

Term

�nal

bloc

kP

ower

sup

ply

Sym

bol

<Sym

bol e

xpla

natio

n>

Page 14: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 7 -

(2) PUHY-P300YJM-A(-BS)

+-

++

+

+

2 1

++

++

+

3 3

2 2

Heat

exc

hang

er c

apac

�ty c

ontro

lCo

ol�n

g/He

at�n

g sw

�tch�

ng21

S4b,

c

*7

63HS

1

SV9

SV5b

,c

For o

pen�

ng/c

los�n

g th

e by

pass

circu

it un

der t

he O

/S

21S4

a4-

way

valve

Expl

anat

�on

Sym

bol

63H1

63LS

Pres

sure

sens

or

Pres

sure

sw�tc

hH�

gh p

ress

ure

prot

ect�o

n fo

r the

outd

oor u

nit

D�sc

harg

e pr

essu

reLo

w pr

essu

re72

CM

agne

t�c re

lay(

�nve

rter m

a�n

c�rcu

�t)Cu

rrent

sen

sor(A

C)Cr

ankc

ase

heat

er(fo

r hea

t�ng

the

com

pres

sor)

CH11

CT12

,22,

3

HIC

bypa

ss,C

ontro

ls re

fr�ge

rant

flow

�n H

IC c

�rcu�

t

Sole

noid

valve

L�ne

arex

pans

�on

valve

LEV1

LEV2

SV1a

DCL

DC re

acto

r

Pres

sure

con

trol,R

efr�g

eran

t flo

wra

te c

ontro

l

TB1

TB3

TB7

Term

�nal

bloc

k

Cent

ral c

ontro

l tra

nsm

�ss�o

nca

ble

Indo

or/O

utdo

or tr

ansm

issio

nca

ble

Powe

r sup

ply

TH2

TH3

TH4

TH5

TH6

TH7

THHS

Func

t�on

sett�

ng c

onne

ctor

IPM

tem

pera

ture

OA

tem

pera

ture

Subc

oole

d liq

uid

refri

gera

ntte

mpe

ratu

re

ACC

�nle

t p�p

e te

mpe

ratu

reD�

scha

rge

p�pe

tem

pera

ture

Subc

ool b

ypas

s ou

tlet

tem

pera

ture

Ther

m�st

or

Z24,

25

P�pe

tem

pera

ture

Out

door

uni

t hea

t exc

hang

erca

pac�t

y co

ntro

lFo

r ope

n�ng

/clo

s�ng

the

bypa

ssc�r

cu�t

21S4

c

X08

15

X07

SV5c

3CN

507

red

6

P200

/P25

0/P3

00EP

200

Appl

�anc

e*7

.Diff

eren

ce o

f app

l�anc

eM

odel

nam

e*7

do

not e

xist

*7 e

xist

P350

/P40

0EP

250

3 C

N3gr

een

1

N

N

L

N

TB24

*1.S

ingl

e-do

tted

lines

indi

cate

wiri

ng n

ot s

uppl

ied

with

the

unit.

*2.D

ot-d

ash

lines

indi

cate

the

cont

rol b

ox b

ound

arie

s.*3

.Ref

er to

the

Data

boo

k fo

r con

nect

ing

inpu

t/out

put s

igna

l con

nect

ors.

*4.D

aisy

-cha

in te

rmin

als

(TB3

) on

the

outd

oor u

nits

in th

e

sam

e re

fr�ge

rant

sys

tem

toge

ther

.*5

.Fas

ton

term

inal

s ha

ve a

lock

ing

func

tion.

M

ake

sure

the

term

inal

s ar

e se

cure

ly lo

cked

in

pla

ce a

fter i

nser

tion.

Pre

ss th

e ta

b

on th

e te

rm�n

als

to re

mov

e th

em.

*6.C

ontro

l box

hou

ses

high

-vol

tage

par

ts.

Be

fore

insp

ectin

g th

e in

side

of th

e

cont

rol b

ox,tu

rn o

ff th

e po

wer,k

eep

th

e un

�t of

f for

at l

east

10

m�n

utes

,

and

conf

irm th

at th

e vo

ltage

bet

ween

FT

-P a

nd F

T-N

on IN

V Bo

ard

has

drop

ped

to

DC2

0V o

r les

s.

L3L1

L2Po

wer S

ourc

e 3

N~ 5

0/60

Hz 3

80/4

00/4

15V

21S4

bCN

501

X01

13

X09

36

CN50

8bl

ack

Unit

addr

ess

sett�

ng

CN50

4gr

een

CT12

C31

C33

CN5

red

D1R4

Z5

1

SV9

R631

wh�te

TH2

t °

C8

red

CNIT

yello

w C

NS2

t °

1

1

LED1

D�sp

lay

sett�

ngCN

5112

V

Func

t�on

sett�

ng

SW1

101

CN21

2

CNTY

P4gr

een

F4 AC25

0V6.

3A T

R5

F3 F1Z4 R2

F2

*3

32

Com

pres

sor O

N/O

FF o

utpu

tEr

ror d

etec

tion

outp

ut

CN20

1

Z25

1 4 1

1

1

TH3

Z3

3

Z2U

ON

OFF

SW2

101SW

U2

LED1

C4

C35

C37

R31

R33

R30

ON

SW3

10

Cont

rol B

oard

TH7

CN40

63HS

1

CN41

TH6

t °tTH

4

32 2

2

1

SW5

LED3

:Lit

when

pow

ered

13

4

R32

2

Z1

1

DSA

C10

R34

R35

LEV1

LEV2

C36

3

C34

SC-V

CT22

SC-U

V1

CN4

blue

red

1M

1

1

t

LED3

:CPU

�n

ope

rat�o

n

blac

k

4

1CN

TYP2

blac

k

3

6

yello

w C

N3K

*3

3

M

C3

TB21

C1

R3

3

CN1A

5

U

CN2

blue

CN3N

5

6

C7

U

44

R1

CN21

blue

TB1

1

CN1B

3TB

7 Po

wer

sele

ct�n

gco

nnec

tor

CN10

2

CNVD

C

3

2

1

IPM

2

1

U

4

TP1

W

L3

DCL

V

blac

k

72C

wh�te

red

32

1

ON

OFF

1

M-N

ET p

ower

supp

ly c�r

cu�t

12

3

C6

M-N

ET B

oard

12

1

Powe

r fa�

lure

dete

ctio

n cir

cuit

1

CNAC

2bl

ack

CN50

2

5

Indo

or/O

utdo

ortra

nsm

�ss�o

nca

ble

INV

Boar

dre

d

3

CNT0

1

TB23

L2L1

U

4

1

ON

1

2

1's

digi

t

THHS

1

CNIT

red

S

2

1

1

CN99

0

1

3 W

TB3

10's

digi

t

OFF

LED2

:CPU

�n o

pera

t�on

5

2

CNS

2ye

llow

TB7

1

CNDC

p�nk

M1

2

2

red

6

MS 3~

1

1

t

C100

*5

3

3

U1

4

LED1

:Pow

er s

uppl

y to

I

ndoo

r/Out

door

t

rans

m�ss

�on

l�ne

ZNR0

1

M2

32

M1

blac

k

Cent

ral c

ontro

ltra

nsm

�ss�o

nca

ble

*6

SC-L

1

1

4

C2C9

ON

C5

OFF

FT-N

R5

M 3~

M

otor

(Com

pres

sor)

°

CN5

Vye

llow

5

2

3

3

3red

CN3S

11

CN04

red

1

CN2

2

3

CN4

X05

2

2

Fan

mot

or(H

eat e

xcha

nger

)

SC-P

2 P

1

CN21

1

CN20

2 re

d

TH5

°

N

CN1

M2

2

TP2

LED1

:Nor

mal

ope

rat�o

n(L�

t)

/ Er

ror(B

l�nk)

2

CN50

3bl

ue

5

X04

4

*4

SC-W

U

C32

SC-L

3

CH11

CN50

6

12

CN72

red

3

P63H1

CN80

1ye

llow

1

2

CN33

2bl

ue

F1,F

2,F3

AC25

0V6.

3A T

21

OFF

SW4

10

1

CNT0

2

11

CN3D

43

2

1

21

CPU

powe

rsu

pply

c�rcu

�t

CNAC

red

2

1

F01

AC25

0V3.

15A

T

1

t

ON

OFF

10

SWU1

wh�te

CN21

3 re

d

SC-L

2

3

Z24

7

4

°

32

11

22

7

12

CN5

1 CN4

red

CNIN

V

3

4

R630

1

1

C630

3

CN22

red

C631

5

F01

DC70

0V4A

T

1

CNTY

P5gr

een

4

LED2

:Erro

r

21S4

a

1

LED1

:Nor

mal

o

pera

t�on

2

3 2

U

X02

X03

CN18

Vbl

ue

5

1

7

CN4

3CN

6

2

°IP

M4

SC-P

1

FT-P

blac

k

C30re

d

DB1

CT3

72C

C1CN

2 CNTY

Pbl

ack

R1bl

ack

TB22

6

3

RSH1

CN10

2

3

R6C1

1

1

1

1

FAN

Boar

d

63LS

ZNR1

U3

No�se

F�lte

r

SV5b

red

CNLV

A

CNLV

B re

d

12345 6

wh�te

blac

k

SV1a

6 4 3 2 1 21

L1L2

L3

CN21

5bl

ack

<Sym

bol e

xpla

nat�o

n>

Page 15: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 8 -

(3) PQHY-P300YHM-A

~

CNAC

4

31

CN83

CNOU

T2 43

21

65

CNPW

42

1

75

3

tTH

312

CN21

2

tTH

6

12t

THIN

VCN

TYP1

black

LEVI

NVCN

LVE

123456

LEV2

b

CNLV

C re

d

123456

CN51

0ye

llow

CN50

9blu

e3

CNOU

T1ye

llow

blue

yellow

red

orange

41

1 2 3 4 5 6

6 5 4 3 2 1

CNLV

B re

dLE

V2a

tTH

812

CN99

2ye

llow

12

4

blue

CN63

PW

MF1

SV4d

156X1

2156

SV4b

SV7b

SV7a

3

DCL

t

M1M2

SV1a

Z3

21

-+

C5

SC-L

1

SC-L

2SC

-W

1Z5

R1R2R3

C3 C2F3 F2 F1Z1

Z2

R5D1

R4 R6C1

7

Diod

eBr

idge

C7C8C9C10

C4

C1

C6

TB1

L

F4 AC25

0V6.3

A T black

white

red 31 CN

3gr

een

TB24

TB23

TB22

TB21

CN1B

41

31

CN1A

UU

U

F1,F

2,F3

AC25

0V6.3

A TUZ4

DSA

CN2

6 5 3 1

UZNR0

1

U

+

31

CN5

red

3CN

4blu

e1

C100

R1R5

black

red

2 431

72C bla

ckre

d

SC-P

1SC

-P2

4CN

1 1

CN6

21CN

412

CN2

157 1CN

TYP

black

C1 RSH1

t THHS

FT-P

FT-N

++++

++++

R34

C30

C32

C34

C36

R30

R32

C31

C33

C35

C37

R31

R33

black

white

red

R35

CT3

SC-L

3

IGBT

SC-U

SC-V

CT12

CT22

red

white

black

black

white

red U

VW

TP2

TP1

TB7

SM2

M1TB3

13

CN04

red

CN10

243

21CN

S2ye

llow

2154

32CN

ITre

d

1

63H1

P

LEV1

123456

CNLV

A

3 1CN

TYP2

black

Z24

3 2 1

Z25

CNTY

P5gr

een

CNTY

P4gr

een

4 2 1CN

213

red

CN99

02 1

TH7

TH5

t t

21 363

LS

63HS

121 3

TH2

tTH

4

3 2 1CN

202

red

CN20

123 1

CN21

5bla

ck2 1

CN21

121

red

CNIT

yello

wCN

S25

12

34

14

14

CN41

CN40

CN10

2 43

21

CN3D 1

23

blue

CN3N 1

23

yello

w C

N3K 1

2CN

ACre

d2

13

F01

AC25

0V3.1

5A T

6 3 1

SV9

X09

CN50

8bla

ck

SV4a

X08

X07

1356

CN50

7re

d

6 5 3 1

CN50

6

X13

X05

3 121

S4a

CN50

4gr

een

X04

X03

CH11

3 1CN

503

blue

2 1CN

502

X02

12

CNAC

2bla

ck

65 72C

12CN

72re

d

31

CNDC

pink

12CN

T01

13

1221

CN80

1ye

llow

CNT0

2CN

4

CN2

7 5 1

SW1ON

OFF 1 10

SW2ON

OFF 1 10

SW3ON

OFF 1 10

SW4ON

OFF 1 10

ONOF

F 1 10SW

5

543

12V

1CN

51SWU2

SWU1

10's

digit

1's digit

*1.

Sin

gle-

dotte

d lin

es in

dica

te w

iring

no

t sup

plie

d w

ith th

e un

it.*2

. D

ot-d

ash

lines

indi

cate

the

cont

rol

bo

x bo

unda

ries.

*3.

Ref

er to

the

Dat

a bo

ok fo

r con

nect

ing

in

put/o

utpu

t sig

nal c

onne

ctor

s.*4

. D

aisy

-cha

in te

rmin

als

(TB

3) o

n th

e

heat

sou

rce

units

in th

e sa

me

re

frige

rant

sys

tem

toge

ther

.*5

. Fa

ston

term

inal

s ha

ve a

lock

ing

fu

nctio

n. M

ake

sure

the

term

inal

s

are

secu

rely

lock

ed in

pla

ce a

fter

in

serti

on. P

ress

the

tab

on th

e

term

inal

s to

rem

oved

them

.*6

. C

ontro

l box

hou

ses

high

-vol

tage

par

ts.

B

efor

e in

spec

ting

the

insi

de o

f the

co

ntro

l box

, tur

n of

f the

pow

er, k

eep

th

e un

it of

f for

at l

east

10

min

utes

,

and

conf

irm th

at th

e vo

ltage

bet

wee

n

FT-P

and

FT-

N o

n IN

V B

oard

has

dro

pped

to

20V

DC

or l

ess.

*7.

Ref

er to

the

Dat

a bo

ok fo

r wiri

ng

te

rmin

al b

lock

for P

ump

Inte

rlock

(TB

8).

<Sym

bol e

xpla

natio

n>

Sub

cool

ed li

quid

refri

gera

ntte

mpe

ratu

reTH

6

Pip

e te

mpe

ratu

reTH

3S

ubco

ol b

ypas

s ou

tlet t

empe

ratu

reTH

2

Pre

ssur

e co

ntro

l, R

efrig

eran

t flo

wra

te c

ontro

lLE

V2a

, b

Out

let t

emp.

det

ect o

f hea

t ex

chan

ger f

or in

verte

rTH

INV

Wat

er o

utle

t tem

pera

ture

TH8

Hea

t exc

hang

er c

apac

ity c

ontro

lS

V7a

, bH

eat e

xcha

nger

cap

acity

con

trol

SV

4a, b

, d

Hea

t exc

hang

er fo

r inv

erte

rLE

VIN

V

For o

peni

ng/c

losi

ng th

e by

pass

circ

uit u

nder

the

O/S

HIC

byp

ass,

Con

trols

refri

gera

ntflo

w in

HIC

circ

uit

Fan

mot

or (R

adia

tor p

anel

)M

F1S

V1a

For o

peni

ng/c

losi

ng th

e by

pass

circ

uit

Z24,

25

Ther

mis

tor

Ope

ratio

n O

N s

igna

l, P

ump

Inte

rlock

Dis

char

ge p

ipe

tem

pera

ture

AC

C in

let p

ipe

tem

pera

ture

Wat

er in

let t

empe

ratu

re

IGB

T te

mpe

ratu

reFu

nctio

n se

tting

con

nect

orTH

HS

TH7

TH5

TH4

TB8

Pow

er s

uppl

yE

xpla

natio

n

Indo

or/H

eat s

ourc

e tra

nsm

issi

onca

ble

Cen

tral c

ontro

l tra

nsm

issi

onca

ble

Term

inal

bloc

k

TB7

TB3

TB1S

ymbo

l

DC

reac

tor

DC

LLE

V1

Line

arex

pans

ion

valv

e

Sol

enoi

dva

lve

CT1

2, 2

2, 3

CH

11C

rank

case

hea

ter (

for h

eatin

g th

e co

mpr

esso

r)C

urre

nt s

enso

r (A

C)

Mag

netic

rela

y (in

verte

r mai

n ci

rcui

t)72

CLo

w p

ress

ure

Hig

h pr

essu

re

Hig

h pr

essu

re p

rote

ctio

n fo

r the

heat

sou

rce

unit

Pre

ssur

esw

itch

Pre

ssur

ese

nsor

63LS

63H

1Sym

bol

Exp

lana

tion

4-w

ay v

alve

21S

4a

SV

9

63H

S1

RELA

Y Bo

ard

Noise

Filte

r

INV

Boar

d

M-N

ET B

oard

Cont

rol B

oard

Powe

r Sou

rce

3N~

50/6

0Hz

380/

400/

415V

NL3

L2L1

NL3

L2L1

P N

Pum

p In

terlo

ckO

pera

tion

ON

sig

nal

M

otor

(Com

pres

sor)

MS 3~

1TB

82

34

*7

*5

*6

*4OFF

ON

*3

LED1

*3

Unit a

ddre

ssse

tting

LED1

Disp

layse

tting

Func

tion

settin

g

Com

pres

sor O

N/OF

F ou

tput

Erro

r det

ectio

n ou

tput

TB7

Powe

rse

lectin

g

LED3

:Lit w

hen

powe

red

LED2

:CPU

in o

pera

tion

LED

1 : N

orm

al o

pera

tion

(lit)

/

Err

or (b

link)

CP

U p

ower

supp

ly c

ircui

t

Pow

er fa

ilure

dete

ctio

n ci

rcui

t

M-N

ET

pow

ersu

pply

circ

uit

Cen

tral c

ontro

ltra

nsm

issi

onca

ble

Indo

or/

Hea

t sou

rce

trans

mis

sion

cabl

e

LED

1:P

ower

sup

ply

to In

door

/Hea

t sou

rce

trans

mis

sion

line

MMMM

°°° ° °° ° °

conn

ecto

rM

°

NL3

L2L1

Page 16: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 9 -

4.Accessories(1) PWFY

(A) Strainer (B) Heat insulation material (C) Connecter sets 2 (D) Expansion joint 2 (E) Wire (F)

(A) Install the strainer at the water pipe inlet.(B) This insulation is for exclusive use with the strainer. Wrap the strainer with the insulation after water pipes are

installed.(C) These are analog input connectors. Cut the wire before using.(D) Install them at the strainer inlet. Refer to P28 for details.(E) To perform test run before the pump interlock circuit is completed, short circuit the terminal block TB142A (IN1),

and then perform test run.(F) When installing the unit, be sure to install the supplied flow switch on the water outlet side of the unit and connect the

wire to IN1 of TB142A on the unit.

Page 17: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 10 -

ProductData III1.Capacitytables(1) Correction by temperature (Estimated performance without defrost) (1)-1 PUHY-P300YJM-A(-BS) + PWFY-P200VM-E1-AU (for standard)

PUHY-P300YJM-A + PWFY-P200VM-E1-AU (for standard)

1.3

1.2

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

Outdoor temp. [°CWB]

Rat

io o

f hea

ting

capa

city

HEX

uni

t out

let-w

ater

tem

p.[°

C]

Rat

io o

f out

door

uni

t inp

ut

35°C

40°C

10°C20°C30°C

40°C

35°C

30°C

20°C

10°C

40°C

35°C

20°C

30°C

10°C

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

50

45

40

35

30

25

20

15

10

5

0

1.2

1.1

1.0

0.9

0.8

0.7

0.6

0.5

0.4

Outdoor temp. [°CWB]

Outdoor temp. [°CWB]

-20 -15 -10 -5 0 5 10 15

-20 -15 -10 -5 0 5 10 15

-20 -15 -10 -5 0 5 10 15

Page 18: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 11 -

(1)-2 PUHY-P300YJM-A(-BS) + PWFY-P200VM-E1-AU (for high temperature flow)

PUHY-P300YJM-A + PWFY-P200VM-E1-AU (for high temperature flow)

1.6

1.4

1.2

1.0

0.8

0.6

0.4

0.2

0.0

Outdoor temp. [°CWB]

Rat

io o

f hea

ting

capa

city

HEX

uni

t out

let-w

ater

tem

p.[°

C]

Rat

io o

f out

door

uni

t inp

ut

46°C

48°C

50°C

54°C

52°C

40.1°C

42°C

44°C

54°C52°C50°C48°C46°C44°C42°C40.1°C

40.1°C

42°C

46°C

50°C

44°C

48°C

52°C

54°C

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

-5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

585756555453525150494847464544

-5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1.4

1.2

1.0

0.8

0.6

0.4

0.2 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Outdoor temp. [°CWB]

Outdoor temp. [°CWB]

*Ratio of heating capacity ··· PWFY-P200VM-E1-AU heating capacity (25kW) base. (Estimated performance without defrost)

*HEX unit outlet-water temp. ··· Peak water temp.

Page 19: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 12 -

(1)-3 PQHY-P300YHM-A + PWFY-P200VM-E1-AU (for standard)

PQHY-P300YHM-A + PWFY-P200VM-E1-AU (for standard)

1.1

1.0

0.9

0.8

0.7

0.6

0.5

Heat source unit inlet-water temp. [°C]

Rat

io o

f HEX

uni

t hea

tling

cap

acity

HEX

uni

t out

let-w

ater

tem

p.[°

C]

Rat

io o

f hea

t sou

rce

unit

inpu

t

40°C

10°C20°C30°C

40°C

30°C

20°C

10°C

40°C

30°C

10°C20°C

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

-5 0 5 10 15 20 25 30 35 40 45

50

45

40

35

30

25

20

15

10

1.6

1.5

1.4

1.3

1.2

1.1

1.0

0.9

0.8

0.7

0.6

Heat source unit inlet-water temp. [°C]

Heat source unit inlet-water temp. [°C]

-5 1550 10 20 25 30 35 40 45

-5 1550 10 20 25 30 35 40 45

Page 20: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 13 -

(1)-4 PQHY-P300YHM-A + PWFY-P200VM-E1-AU (for high temperature flow)

PQHY-P300YHM-A + PWFY-P200VM-E1-AU (for high temperature flow)

1.4

1.2

1.0

0.8

0.6

0.4

0.2

0.0

Heat source unit inlet-water temp. [°C]

Rat

io o

f hea

ting

capa

city

HEX

uni

t out

let-w

ater

tem

p.[°

C]

Rat

io o

f hea

t sou

rce

unit

inpu

t

46°C

48°C

50°C

54°C

52°C

40.1°C42°C

44°C

54°C52°C50°C48°C46°C44°C42°C40.1°C

40.1°C

42°C

46°C

50°C

44°C

48°C

52°C

54°C

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

HEX unit inlet-water temp. [°C]

-5 0 5 10 15 20 25 30 35 40 45

-5 0 5 10 15 20 25 30 35 40 45

-5 0 5 10 15 20 25 30 35 40 45

585756555453525150494847464544

1.4

1.2

1.0

0.8

0.6

0.4

0.2

Heat source unit inlet-water temp. [°C]

Heat source unit inlet-water temp. [°C]

*Ratio of heating capacity ··· PWFY-P200VM-E1-AU heating capacity (25kW) base. (Estimated performance without defrost)

*HEX unit outlet-water temp. ··· Peak water temp.

Page 21: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 14 -

(2) Correct�on by water flow ratePWFY-P200VM-E1-AU

Heating Cooling

1.5 2.0 2.5 3.0 3.5 4.0 4.5

1.5 2.0 2.5 3.0 3.5 4.0 4.5

1.5 2.0 2.5 3.0 3.5 4.0 4.5

1.5 2.0 2.5 3.0 3.5 4.0 4.5

HEX unit water-volume [m3/h] HEX unit water-volume [m3/h]

HEX unit water-volume [m3/h] HEX unit water-volume [m3/h]

Ratio

of H

EX u

nit h

eatin

g ca

pacit

y

Ratio

of H

EX u

nit c

oolin

g ca

pacit

y

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

Rat

io o

f out

door

uni

t in

put

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

Rat

io o

f out

door

uni

t in

put

Page 22: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 15 -

(3) Correction at frosting and defrostingDue to frost at the outdoor heat exchanger and the automatic defrost operation, the heating capacity of the outdoor unit can be calculated by multiplying the correction factor shown in the table below.

Table of correction factor at frost and defrostOutdoorinletairtemp.°C 6 4 2 1 0 -2 -4 -6 -8 -10 -20Outdoorinletairtemp.°F 43 39 36 34 32 28 25 21 18 14 -4PUHY-P300YJM-A (-BS) 1.00 0.93 0.82 0.80 0.82 0.86 0.90 0.90 0.95 0.95 0.95

(4) Water pressure drop

(4)-1 PWFY-P200VM-E1-AU (with strainer)

HEX unit inlet-water volume [m3/h]

HEX

unit

wate

r-pre

ssur

e dro

p [k

Pa]

0

10203040

50607080

90100

PWFY-P200VM-E1-AU (with strainer)

1.5 2 2.5 3 3.5 4 4.5

Water pressure drop of strainer

(4)-2 Water pressure drop of Strainer only (accessory for PWFY-P200VM-E1-AU)

0

10

20

30

40

ATW unit inlet-water volume [m3/h]

Wat

er-p

ress

ure

drop

[kPa

]

0.5 1 1.5 2 2.5 3 3.5 4 4.5

Page 23: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 16 -

(5) Operat�on temperature rangePWFY-P200VM-E1-AU

Heating

0

10

20

30

40

50

60

Outdoor temp. [°CWB]

HEX u

nit in

let w

ater t

emp.

[°C]

PUHY-P300YJM-A(-BS)

-5-10-15-20 0 5 10 15 20 25 30 35 40 45 50

Heating

0

10

20

30

40

60

50

Heat source unit circulating water temp. [°C]

HEX

unit

inle

t wat

er te

mp.

[°C]

PQHY-P300YHM-A

-5-10-15-20 0 5 10 15 20

WaterBrine

25 30 35 40 45 50

Page 24: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 17 -

Cooling

0

10

20

30

40

50

Outdoor temp. [°CDB]

HEX

unit

inlet

wat

er te

mp.

[°C]

PUHY-P300YJM-A(-BS)

-5-10-15-20 0 5 10 15 20 25 30 35 40 45 50

Cooling

0

10

20

30

40

50

Heat source unit circulating water temp. [°C]

HEX

unit

inlet

wat

er te

mp.

[°C]

PQHY-P300YHM-A

-5-10-15-20 0 5 10 15 20 25 30 35 40 45 50

WaterBrine

Page 25: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 18 -

2.Soundpressurelevels(1) PWFY-P200VM-E1-AU

50/60HzWhen Low noise mode is set,the A/C system's capacity is limited. The system could return to normal operation from Low noise mode automatically in the case that the operation condition is severe.

10

20

30

40

50

60

70

80

90

63 125 250 500 1k 2k 4k 8k

NC-40

NC-30

NC-20

NC-60

NC-50

NC-70

Octave band central frequency (Hz)

Oct

ave

band

sou

nd le

vel (

dB)

Sound level of PWFY-P200VM-E1-AU

Approximate minimumaudible limit oncontinuous noise

dB(A)29.0

8k12.0

4k15.0

2k14.5

1k22.5

500k25.0

25033.0

12532.0

6342.0

Measurement conditionPWFY-P200VM-E1-AU

Measurementlocation

1m

1m

3.Refrigerantcircuitdiagramsandthermalsensors(1) PWFY-P200VM-E1-AU

Hex

TH6

TH23

LEV1Wa

TH8

TH22

LEV1Wb

SV1

ST2

ST4

CV1

Water inlet

Water outlet

screw

screw

Brazed

Brazed

Page 26: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 19 -

++

A. For Air conditioning using such as Panel Heaters, Floor Heating and Fan coil unitsRequired total heating capacity kWSafety factor; %

B. For Sanitary use such as Shower and BathroomsConditions

Tank inlet water Temp.; °CTank outlet water Temp.; °C(Set Temp -5 °C)Safety factor for Heat Loss; %Operating time; HoursFor Shower; /person x Person = (Water Temp. Condition °C)

°C)For Bathrooms; /Person x Person = (Water Temp. ConditionThe conversion of water volume to °C

x ( - ) / ( - )+ x ( - ) / ( - )= ℓ /dayHeating Capacity Calculation for sanitary usage

/ 1,000 x ( - ) = M cal / dayThe conversion of M cal to kW

/ 860 x 1,000 / = kWC. Total (A+B)

Total Heating Capacityx (100%

+x (100%

%) + x (100% %) = kWD. No. of units required

Safety factor; %%) / 12.5 kW = units

units are required

TankPWFY unit 4

3 3

33

7

1.Howtocalculatethenecessaryheatingcapacity(1) Heat�ng capac�ty calculat�on

(2) Calculat�on example

++

A. For Air conditioning using such as Panel Heaters, Floor Heating and Fan coil unitsRequired total heating capacity 20

10

1060

60

158

2030

1,200240

4045

1,200240

4045

1010

6060

1010

888

888

44.4

20

29.42 20

3

2.82

10

20

6.45 15 29.42

8 6.45

60 10 44.4

kWSafety factor; %

B. For Sanitary use such as Shower and BathroomsConditions

Tank inlet water Temp.; °CTank outlet water Temp.; °C(Set Temp -5 °C)Safety factor for Heat Loss; %Operating time; HoursFor Shower; 60 /person x Person = (Water Temp. Condition °C)

°C)For Bathrooms; 8 /Person x Person = (Water Temp. ConditionThe conversion of water volume to °C

x ( - ) / ( - )+ x ( - ) / ( - )= ℓ /dayHeating Capacity Calculation for sanitary usage

/1,000 x ( - ) = M cal / dayThe conversion of M cal to kW

/ 860 x 1,000 / = kWC. Total (A+B)

Total Heating Capacityx (100%

+x (100%

%) + x (100% %) = kWD. No. of units required

Safety factor; %%) / 12.5 kW = units

units are required

TankPWFY unit 4

3 3

33

7

Installation IV

Page 27: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 20 -

2.Installation(1) Selecting an installation site (for PWFY unit)• Donotinstalloutdoors.Theunitisnotwaterproof.• BackupsystemisrecommendedincaseofPWFYunitbreakdown.• Theunitwillgethot.Donotinstallinalocationwhereheatgetstrappedinside.• Besuretoinstallunitinaplacestrongenoughtowithstanditsweight. Anylackofstrengthmaycauseunittofalldown,resultinginapersonalinjury.• Donotinstalltheunitwherecorrosivegasisgenerated.• Haveinstallationworkinordertoprotectagainstearthquake. Anyinstallationdeficiencymaycauseunittofalldown,resultinginapersonalinjury.• Payaspecialattentiontotheplace,suchasabasement,etc.whererefrigerationgascanstay,sincerefrigera-

tionisheavierthantheair.• Donotinstalltheunitwherecombustiblegasmayleak.- If the gas leaks and accumulates around the unit, an explosion may result.• Wheninstallingtheunitinahospital,communicationstation,orsimilarplace,providesufficientprotection

againstnoise.- The inverter equipment, private power generator, high-frequency medical equipment, or radio communication

equipment may cause the air conditioner to operate erroneously, or fail to operate. On the other hand, the air conditioner may affect such equipment by creating noise that disturbs medical treatment or image broadcasting.

• Donotinstalltheunitonastructurethatmaycauseleakage.- When the room humidity exceeds 80 % or when the drain pipe is clogged, condensation may drip from the indoor

unit. Perform collective drainage work together with the unit, as required.• ItisrecommendedthatawaterpumpisconnectedtoeachPWFYunit.

(1)-1 Securing installation and service space• Please secure the following service spaces after installation. (All servicing can be performed from the front of the unit) [Fig. IV. 2. (1). 1]

Warning:• Besuretoinstalltheunitinalocationwhichcanadequatelysupportitsweight.- If there is insufficient strength to support the unit’s weight, it could fall and cause injuries.

(A) Piping space (right side)(B) Top v�ew(C) Service space (front side)

(A) Piping space (right side)(B) Top v�ew(C) Service space (front side)

(B)

400mm

300mm

600mm(C)

(A)

Page 28: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 21 -

(2) Install�ng the un�t(2)-1 Lifting method

(2)-2 Product net weight

Model

Net we�ghtPWFY-P200VM-E1-AU

38 kg

PUHY-P300YJM-A(-BS)

215 kg

(2)-3 Center of grav�ty

(2)-3-1 PWFY-P200VM-E1-AU

X277

ModelPWFY-P200VM-E1-AU

Z99

Y347

20513

X

Y

800

500

525

300450

Z

47

Unit : mm

· Products weighing more than 20 kg [45 LBS] should not be carried alone.· Do not carry the product by the PP bands.· To avoid the risk of injury, do not touch the heat exchanger fins. · Plastic bags may pose a risk of choking hazard to children. Tear plastic bags into pieces before disposing of them.· When lifting and transporting outdoor units (heat source unit) with ropes, run the ropes through lifting hole at the unit base. Securely fix the unit so that the ropes will not slide off, and always lift the unit at four points to prevent the unit from falling.

Exercise caution when transporting products.CAUTION

Page 29: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 22 -

(2)-3-2 PUHY-P300YJM-A(-BS)

760 80

Y

724

1470

Z

60

920

X

760

Model

Unit:mm

X Y Z320 319 632PUHY-P300YJM-A (-BS)

(2)-3-3 PQHY-P300YHM-A

Model X Y Z418[16-8/16] 250[9-14/16] 532[21]PQHY-P300YHM-A

Unit : mm[in.]

1100

[43-

5/16

]60

[2-6

/16]

550[21-11/16]880[34-11/16]

506[19-15/16]

YX

Z

1160

[45-

11/1

6]

80[3-3/16]

720[28-6/16]

Page 30: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 23 -

(2)-4 Installation method

• Using the anchoring holes shown below, firmly bolt the unit to the base. [Fig. IV. 2. (2). 1]

Bases• Be sure to install unit in a place strong enough to withstand its weight. If the base is unstable, reinforce with a con-

crete base.• The unit must be anchored on a level surface. Use a level to check after installation.• If the unit is installed near a room where noise is a problem, using an anti-vibration stand on the base of the unit is

recommended.

(A) 4-ø14 (Anchor�ng hole)(B) (Top v�ew)

(A)

(B)

205

300

450

500

525

Un�t : mm

Page 31: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 24 -

(3) Refrigerant pipe and drain pipe specifications

(3)-1 Refrigerant pipe and drain pipe specifications

(3)-2 Refrigerant pipe, drain pipe and filling port

ModelGas

LiquidDra�n

Insulating material's thickness

PWFY-P200VM-E1-AUø19.05ø9.52ø32

More than 10 mm

To avoid dew drops, provide sufficient antisweating and insulating work to the refrigerant and drain pipes.When using commercially available refrigerant pipes, be sure to wind commercially available insulating material (with a heat-resisting temperature of more than 100 °C and thickness given below) onto both liquid and gas pipes.Be also sure to wind commercially available insulating material (with a form polyethylene’s specific gravity of 0.03 and thickness given below) onto all pipes which pass through rooms.1) Select the thickness of insulating material by pipe size.

2) If the unit is used on the highest story of a building and under conditions of high temperature and humidity, it is necessary to use pipe size and insulating material’s thickness more than those given in the table above.

3) If there are customer’s specifications, simply follow them.

(A) Refr�gerant p�p�ng (gas)(B) Refrigerant piping (liquid)(C) Water �nlet(D) Water outlet(E) Dra�n outlet

(D)

(A)

(B)

(C)

(E)

480

100

191

54102

114

134

206

Unit : mm

Un�t : mm

Page 32: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 25 -

(4) Connecting refrigerant pipes and drain pipes

(4)-1 Refr�gerant p�p�ng workThis piping work must be done in accordance with the installation manuals for outdoor unit (heat source unit).• For constraints on pipe length and allowable difference of elevation, refer to the outdoor unit installation manual.• The method of pipe connection is brazing connection.

Caution:• Installtherefrigerantpipingfortheindoorunitinaccordancewiththefollowing.1. Cut the tip of the indoor unit piping, remove the gas, and then remove the brazed cap. [Fig. IV. 2. (4). 1]

2. Pull out the thermal insulation on the site refrigerant piping, braze the unit piping, and replace the insulation in its original position.

Wrap the piping with insulating tape.Note:• Paystrictattentionwhenwrappingthecopperpipingsincewrappingthepipingmaycausecondensation

insteadofpreventingit.* Before brazing the refrigerant piping, alwayswrapthepipingonthemainbody,andthethermalinsulation

piping,withdampclothstopreventheatshrinkageandburningthethermalinsulationtubing. Take care to ensure that the flame does not come into contact with the main body itself.

[Fig. IV. 2. (4). 2]

(A)

(A)

(E)

(C)

(F)

(B)

(D)

(A) Thermal �nsulat�on(B) Pull out �nsulat�on(C) Wrap with damp cloth(D) Return to or�g�nal pos�t�on(E) Ensure that there �s no gap here(F) Wrap w�th �nsulat�ng tape

(A) Cut here(B) Remove brazed cap

(4)-2 Mixed system of PWFY-AU and Indoor unit (Y, WY system)Take one of the options listed below. 1) Install the External Solenoid Valve (External Solenoid Valve kit (PAC-SV01PW-E) will be available in Nov. 2012.)2) Add brine, assuming that the temperature will drop to -20°C. Set Dip SW 1-10 (on ATW unit) to ON if brine is added. *See section IV.3.(9) for the brine concentration graphs.* With the WY system, the above steps apply only when operating the WY at the water temperature below 10ºC.

(4)-3 PWFY-AU in cooling operation (Y, WY system)Add brine, assuming that the temperature will drop to -20°C. Set Dip SW 1-10 (on ATW unit) to ON if brine is added.* With the WY system, the above steps apply only when operating the WY at the water temperature below 10ºC.

Page 33: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 26 -

CautionsOnRefrigerantPiping

• Besuretousenon-oxidativebrazingforbrazingtoensurethatnoforeignmatterormoistureenterintothepipe.

• esuretoapplyrefrigeratingmachineoilovertheflareconnectionseatingsurfaceandtightentheconnectionusingadoublespanner.

• Provideametalbracetosupporttherefrigerantpipesothatnoloadisimpartedtotheindoorunitendpipe.Thismetalbraceshouldbeprovided500mmawayfromtheindoorunit’sflareconnection.

Warning:Wheninstallingandmovingtheunit,donotchargeitwithrefrigerantotherthantherefrigerant(R407CorR22)specifiedontheunit.- Mixing of a different refrigerant, air, etc. may cause the refrigerant cycle to malfunction and result in severe damage.

Caution:• UserefrigerantpipingmadeofC1220(CU-DHP)phosphorusdeoxidizedcopperasspecifiedintheJISH3300

“Copperandcopperalloyseamlesspipesandtubes”.Inaddition,besurethattheinnerandoutersurfacesofthepipesarecleanandfreeofhazardoussulphur,oxides,dust/dirt,shavingparticles,oils,moisture,oranyothercontaminant.

• Neveruseexistingrefrigerantpiping.- The large amount of chlorine in conventional refrigerant and refrigerator oil in the existing piping will cause the new

refrigerant to deteriorate.• Storethepipingtobeusedduringinstallationindoorsandkeepbothendsofthepipingsealeduntiljust

beforebrazing.- If dust, dirt, or water gets into the refrigerant cycle, the oil will deteriorate and the compressor may fail.

(4)-4 Dra�n p�p�ng work

1. Ensure that the drain piping is downward (pitch of more than 1/100) to the outdoor (discharge) side. Do not provide any trap or irregularity on the way. (a)

2. Ensure that any cross-wise drain piping is less than 20 m (excluding the difference of elevation). If the drain piping is long, provide metal braces to prevent it from waving. Never provide any air vent pipe. Otherwise drain may be ejected.

3. Use a hard vinyl chloride pipe VP-25 (with an external diameter of 32 mm) for drain piping.4. Ensure that collected pipes are 100 mm lower than the unit body’s drain port as shown in (b). 5. Do not provide any odor trap at the drain discharge port.6. Put the end of the drain piping in a position where no odor is generated.7. Do not put the end of the drain piping in any drain where ionic gases are generated. [Fig. IV. 2. (4).3]

(A) Downward slope 1/100 or more(B) Dra�n hose(C) Un�t (D) Collect�ve p�p�ng(E) Maximize this length to approx. 100 mm(A)

(B) (a)

(C) (C) (C)

(D) (b)

(E)

Page 34: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 27 -

3.Waterpipeinstallation(1) Water c�rcu�t sample

Water-side heat exchanger

Solid arrows in the figure indicate the direction of water flow.

PWFY Field supply

Tank Outlet

Inlet

City waterOverflowed water

Roof

To drain outlet

Uphill gradient ≥ 1/200

P

P

T

T

P

1)

1)

1)

1)

2)13)

2)

3)14) Tank

3) 3)

4)

4) 4)4)

5)

5) 5)

6)

7)

8) 8)

9)

11) 11)12)

Sample of water circuit for PWFY

Consider the following when designing and installing a water piping system. (Items (1)-(14) in the figure are explained below.) 1) Union joints/flange joints etc. Install a flange etc. to allow for easy replacement of connected equipment.2) Thermometer For checking unit performance and operation monitoring3) Water pressure gauge For operat�on status mon�tor�ng4) Valve Install a valve for easy replacement and cleaning of the refrigerant flow control device. Install a refrigerant flow control valve on the fan coil outlet side.5) Flex�ble jo�nt Recommended to prevent the noise and vibration from the pump from being transmitted. 6) Dra�n p�pe Install the drain pipe with an inclination of between 1/100 and 1/200 to provide a downward flow of drain water. For cold climate installation, take an appropriate measure (e.g., drain heater) to prevent the drain water from

freezing.7) Pump Use a pump that is large enough to compensate for the total water pressure loss and to supply sufficient water to the

unit.8) Air vent valve Provide air vent valves on the pipes.9) Expans�on tank Install an expansion tank to accommodate expanded water and to supply water.10) Cold/Hot water pipe Use pipes that allow for easy air purging, and provide sufficient insulation.11) Dra�n valve Install drain valves so that water can be drained for servicing.12) Stra�ner Install a strainer near the PWFY unit to keep foreign materials from entering the water-side heat exchanger. 13) Flow sw�tch Install the supplied flow switch on the outlet pipe.14) Tank Minimum tank capacity : 100 L (Refer to Fig. IV.3.(8).1)

Page 35: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 28 -

(1)-1 Caut�on for water p�pe �nstallat�onConsider the following when designing and installing a water piping system.• Do not use steel pipes as water pipes.- Copper pipes or stainless steel pipes are recommended.If iron pipes are used in the existing system, do not connect

a new circuit to the old one. Keep the existing and new circuits separate. • Light pipes are similar to other air-conditioning pipes, however, please observe the following precautions during installation.• Before a long period of non use, purge the water out of the pipes and thoroughly let them dry. • Use a closed water circuit. • When operating the unit, add brine to the circulating water to prevent it from freezing. To use brine in the system,

DipSW 1-10 must be set to ON.• When installed in a low-ambient temperature environment, keep the water circulating at all times. If that is not

possible, purge the water out of the pipes completely. • Do not use the water used for this unit for drinking or food manufacturing.• When the ambient temperature is 0 ˚C or lower during stop operation, keep the water circulating at all times, or

purge the water out of the pipes completely.

Model Water �nlet Water outletPWFY-P200VM-E1-AU*1 When the attached expansion

joints are installed.PT 1 Screw*1 PT 1 Screw*1

(2) Select�ng a water pumpUse a pump that is large enough to compensate for the total water pressure loss and to supply sufficient water to the unit.

(3) Install�ng the stra�ner• Install the strainer at the angle of 45˚ or less as shown in [Fig. IV 3.(3).1].• Install the supplied strainer at the water inlet.

(4) Precautions during installation• Use the reverse-return method to insure proper pipe resistance to each unit.• To insure easy maintenance, inspection, and replacement of the unit, use a proper joint, valve, etc. on the water

intake and outlet port. In addition, be sure to install a strainer on the water intake pipe. (In order to maintain the heat source unit, a strainer on the circulating water inlet is necessary.)

* An example of the heat source unit installation is shown in [Fig. IV 3.(5).1].• Install a suitable air vent on the water pipe. After sending water through the pipe, be sure to vent the excess air.• Compressed water may form in the low-temperature sections of heat source unit. Use a drainage pipe connected to

the drain valve at the base of the unit to drain the water.• Install a back flow-prevention valve on the pump and a flexible joint to prevent excess vibration.• Use a sleeve to protect the pipes where they go through a wall.• Use metal fittings to secure the pipes, and install them so that they have maximum protection against breakage and

bending.• Do not confuse the water intake and outlet valves.• This unit doesn’t have any heater to prevent freezing within tubes. When the water flow is stopped on low ambient,

take out the water from tubes.• The unused knockout holes should be closed and the opening of refrigerant pipes, water pipes, power source and

transmission wires should be filled with putty and so on to prevent from rain. (field construction)• Wrap some sealing tape around the screw part to prevent water leakage. • Wrap the sealing tape as follows. 1. Wrap the joint with sealing tape in the direction of the threads (clockwise), and do not let the tape run over the edge. 2. Overlap the sealing tape by two-thirds to three-fourths of its width on each turn. Press the tape with your fingers so that it is pressed firmly against each thread. 3. Leave the 1.5th through 2nd farthest threads away from the pipe and unwrapped.• Hold the pipe on the unit side in place with a spanner when installing the pipes or strainer. Tighten screws to a torque

of 50 N.m. • Water pipes can get very hot, depending on the preset temperature. Wrap the water pipes with insulating materials

to prevent burns. • Install the expansion joint (accessory) at the inlet after installing the strainer, and outlet.

(A) Y-type strainer(A)

45°

[Fig. IV 3.(3).1]

Page 36: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 29 -

(5) Example of un�t �nstallat�on[Fig. IV. 3.(5).1]

(A)

(A)(D)

(C)

(B)(E)(F)

(E)(B)

(C) (G)

(G)

PWFY- P200VM-E1-AU(A) Close valve(B) Water �nlet(C) Water outlet(D) Refr�gerant p�p�ng

(E) Y-type strainer(F) Dra�n p�pe(G) Expans�on jo�nt

(6) Insulat�on �nstallat�onThe surface temperature of the water pipe would be very high, depending on the set temperature. Insulate the pipe to prevent burns. When operating PWFY-P200VM-E1-AU with cold water, insulate the water pipe to prevent condensation. Wrap insulation material around water pipes as shown in [Fig. IV. 3.(6).1].• Any heat source piping.• Indoor piping in cold-weather regions where frozen pipes are a problem.• When air coming from the outside causes condensation to form on piping.• Any drainage piping. [Fig. IV. 3.(6).1]

(A) Heat �nsulat�on mater�al (accessory)(B) Inject w�th caulk�ng mater�al

(A)

(B)

(7) Flow sw�tch �nstallat�on<Caution>When installing the unit, be sure to install the supplied flow switch on the water outlet side of the unit and connect the wire to IN1 of TB142A on the unit.If the flow switch is not installed, the unit will emit the error signal (2100: Interlock error) and not operate.* A short-circuit wire is supplied, but it is only for test run.

Page 37: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 30 -

<Installation procedures>1) Remove the pipes attached to the flow switch.

Note: The unit is shipped with the pipes loosely tightened. 2) Wrap seal tape around the threads at the end of the pipes, starting at the 1.5th or 2nd thread, and not over the

openings. Apply two to three wraps in the direction of the pipe threads (clockwise). Each course of the tape should overlap the one before it by 2/3 to 3/4 the width of the tape. Run your fingers around the threads and tape to press the tape into the threads. Then, attach the pipes to the flow switch, holding parts A and B with a spanner. The maximum tightening torque is 60 N•m (611 kgf•cm).

3) Attach the flow switch and pipes to the water outlet in the horizontal position. The angle of the axis of the pipe should be less than 45 degrees. Check the direction of the flow switch as shown in Fig. C.

4) Connect the flow switch wire to IN1 of TB142A. From the External Wiring Input, route the wire as shown in Fig. D and connect it to the terminal as shown in Fig. E. Use a wire protector such as a rubber bushing in the access hole on the unit.

A B

Water Outlet

OKOK OKOK

OKOK

45°45°

Not AcceptableNot Acceptable

Not AcceptableNot Acceptable

1) 2)

3)

Check the direction.

4)

Fig. C

Secure thewiring in place.Secure thewiring in place.

Enlarged viewEnlarged view

Fig. D Fig. E

Flow Switch

Wire

Rubber bushingRubber bushing

Page 38: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 31 -

(8) Water processing and water quality controlTo preserve water quality, use the closed type of cooling tower for unit. When the circulating water quality is poor, the water heat exchanger can develop scales, leading to a reduction in heat-exchange power and possible corrosion of the heat exchanger. Please pay careful attention to water processing and water quality control when installing the water circulation system.• Removal of foreign objects or impurities within the pipes. During installation, be careful that foreign objects, such as welding fragments, sealant particles, or rust, do not enter

the pipes.• Water Qual�ty Process�ng

a) Depending on the quality of the cold-temperature water used in the air-conditioner, the copper piping of the heat exchanger may become corroded. We recommend regular water quality processing.Cold water circulation systems using open heat storage tanks are particularly prone to corrosion.When using an open-type heat storage tank, install a water-to-water heat exchanger, and use a closed-loop circuit on the air conditioner side. If a water supply tank is installed, keep contact with air to a minimum, and keep the level of dissolved oxygen in the water no higher than 1mg/liter.

b) Water quality standard

Reference : Guideline of Water Quality for Refrigeration and Air Conditioning Equipment. (JRA GL02E-1994)c) Please consult with a water quality control specialist about water quality control methods and water quality

calculations before using anti-corrosive solutions for water quality management.

d) When replacing a previously installed air conditioning device (even when only the heat exchanger is being replaced), first conduct a water quality analysis and check for possible corrosion.

Corrosion can occur in cold-water systems even if there has been no prior signs of corrosion.

If the water quality level has dropped, please adjust water quality sufficiently before replacing the unit. Refer to the below graph for the maximum amount of circulating water in the water pipe. Make sure that this amount does not exceed.

[Fig. IV. 3. (8).1] Max�mum c�rculat�ng water

pH (25 ˚C)Electric conductivity (mS/m) (25 ˚C) (µ s/cm) (25 ˚C)Chloride ion (mg Cl-/l�ter)Sulfate �on (mg SO42-/l�ter)Acid consumption (pH4.8) (mg CaCO3/l�ter)Total hardness (mg CaCO3/l�ter)Calcium hardness (mg CaCO3/l�ter)Ion�c s�l�ca (mg S�O2/l�ter)Iron (mg Fe/l�ter)Copper (mg Cu/l�ter)

Sulfide ion (mg S2-/l�ter)

Ammon�um �on (mg NH4+/l�ter)

Residual chlorine (mg Cl/liter)Free carbon dioxide (mg CO2/l�ter)Ryzner stability index

Standard �tems

Refer-ence �tems

ItemsLower mid-range temperature water system

Water Temp. =< 60 ˚C

7.0 ~ 8.030 or less

[300 or less]50 or less50 or less

50 or less

70 or less50 or less30 or less1.0 or less1.0 or lessnot to be detected

0.3 or less0.25 or less0.4 or less

7.0 ~ 8.030 or less

[300 or less]50 or less50 or less

50 or less

70 or less50 or less30 or less0.3 or less1.0 or lessnot to be detected

0.1 or less0.3 or less4.0 or less

Tendency

Rec�rculat�ng water Make-up water Corros�ve Scale-form�ng

Higher mid-range temperature water systemWater Temp. > 60 ˚C

Rec�rculat�ng water Make-up water7.0 ~ 8.030 or less

[300 or less]30 or less30 or less

50 or less

70 or less50 or less30 or less1.0 or less1.0 or lessnot to be detected

0.1 or less0.1 or less0.4 or less

7.0 ~ 8.030 or less

[300 or less]30 or less30 or less

50 or less

70 or less50 or less30 or less0.3 or less1.0 or lessnot to be detected

0.1 or less0.3 or less4.0 or less

0

500

1000

1500

2000

2500

3000

0 10 20 30 40 50 60 70Total hardness [mg/L]

Wat

er v

olum

e lim

itatio

n [L

]

Condition: Water outlet temp. 45°C

PWFY-P200VM-E1-AU

Available water volume area

Page 39: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 32 -

(9) Br�neWhen (a) PWFY-AU is used for cooling purpose, or (b) PWFY-AU is installed in the temperature condition below freezing temperature, Brine is required to add.Set Dip SW 1-10 (on ATW unit) to ON if brine is added.

Brine concentration [wt%]

Free

zing

tem

pera

ture

[ºC

]

0-30

-25

-20

-15

-10

-5

0

5

10 20 30 40 50 60 70

Brine concentration [wt%]

Rat

io o

f cap

acity

[-]

00

0.2

0.4

0.6

0.8

1

1.2

10 3020 40 50 60 70 80 90 100

ethylene glycol

propylene glycol

Brine concentration (wt%)

Rat

io o

f pre

ssur

e dr

op (-

)

0.5

1

1.5

2

2.5

3

3.5

4

0 10 3020 40 50 60 70 80 90 100

ethylene glycol

propylene glycol

Page 40: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 33 -

(10) Pump �nterlockThe unit may become damaged if it is operated with no water circulating through the pipes.Be sure to interlock unit operation and the water-circuit pump. [Fig. IV. 3. (10).1]

IN1

TB142A

Water Pump

Strainer

Control Box

Broken lines are fieldsupply products.

Operation signalPump interlock

Example drawing for pump interlock

In the system including PWFY-P200VM-E1-AU, the circulating water may freeze, and result in a unit malfunction. Perform the electrical work as shown in [Fig. IV. 3. (10).2] to prevent water from freezing.Set the DipSW as shown in the table below.

D�pSW3-6 External output contactON Effect�ve when Thermo-ONOFF Effect�ve when Operat�on-ON

(Remote controller-ON)

Be sure to turn on the power supply of the pump, s�nce the control does not work if the power supply of the pump is turnd off. *Refer to (7) Flow switch installation for details.

F: Fuze52P: Magnet�c contactor for heat source water pumpMCB: C�rcu�t breakerWP: Water pump

(11) Anti freeze mode (Dip SW4-4 ON)Anti freeze mode is to prevent water pipe from freezing.The Anti freeze mode can set the heating temperature range between 10ºC~45ºC enabling the unit to maintain low water temperature to prevent water pipes from freezing.

[Fig. IV. 3. (10).2]

Board

F

NL

52P

MCB

WP

TB141A OUT1AC220V ~ 240V

DC30V or lessor

52P

[Fig. IV. 3. (10).2]

Board

F

NL

52P

MCB

WP

TB141A OUT1AC220V ~ 240V

DC30V or lessor

52P

Page 41: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 34 -

1.Electricalwork(1) General caut�ons

Warning:Electricalworkshouldbedonebyqualifiedelectricalengineersinaccordancewith“EngineeringStandardsForElectricalInstallation”andsuppliedinstallationmanuals.Specialcircuitsshouldalsobeused.Ifthepowercircuitlackscapacityorhasaninstallationfailure,itmaycauseariskofelectricshockorfire.

1. Be sure to take power from the special branch circuit.2. Be sure to install an earth leakage breaker to the power.3. Install the unit to prevent that any of the control circuit cables (remote controller, transmission cables, or external

input/output line) is brought in direct contact with the power cable outside the unit.4. Ensure that there is no slack on all wire connections.5. Some cables (power, remote controller, transmission cables external input/output line) above the ceiling may be

bitten by mouses. Use as many metal pipes as possible to insert the cables into them for protection.6. Never connect the power cable to leads for the transmission cables. Otherwise the cables would be broken.7. Be sure to connect control cables to the indoor unit, remote controller, and the outdoor unit.8. Be sure to ground the unit.9. Select control cables from the conditions given in page 36.

Caution:Besuretoputtheunittothegroundontheoutdoorunitside.Donotconnecttheearthcabletoanygaspipe,waterpipe,lighteningrod,ortelephoneearthcable.Incompletegroundingmaycauseariskofelectricshock.

(2) Power supply for PWFY unit(2)-1 Electrical characteristics of PWFY unit• Power supply cords of appliances shall not be lighter than design 245 IEC 57 or 227 IEC 57.• A switch with at least 3 mm contact separation in each pole shall be provided by the Air conditioner installation.

(2)-2 Power cable spec�f�cat�ons

PWFY-P200VM-E1-AU

Hz

50/60

Volts

220-230-240 V

Voltage rangeMax. 264 VMin. 198 V

MCA (A)

0.085

Cool�ng Heat�ngModel

0.068-0.065-0.063

RLA (A)Power supply

branch1.52.54.0

ModelM�n�mum w�re th�ckness (mm2) Local sw�ch (A)Breaker for current

leakage capac�tyBreaker for w�r�ng (NFB) (A)

Ma�n cable1.52.54.0

Ground1.52.54.0

fuse

PWFY-P200VM-E1-AUTotal operat�ng current

16 A or less25 A or less32 A or less

20 A 30 mA 0.1 sec. or less30 A 30 mA 0.1 sec. or less40 A 30 mA 0.1 sec. or less

203040

16

25

32

162532

[Fig. V. 1.(2).1]

(A) (B)

(D) (D)

PEPE(C) PE(C) (C)

PWFY-P200VM-E1-AU(A) Breaker for current leakage(B) Local sw�tch or breakers for w�r�ng(C) PWFY-P200VM-E1-AU(D) Pull box

Caution:Donotuseanythingotherthanthecorrectcapacitybreakerandfuse.Usingfuse,wireorcopperwirewithtoolargecapacitymaycauseariskofmalfunctionorfire.

SystemDesign V

Page 42: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 35 -

(3) Connecting remote controller, indoor and outdoor transmission cables• Connect unit TB5 and outdoor unit TB3. (Non-polarized 2-wire (shield)) The “S” on unit TB5 is a shielding wire connection. For specifications about the connecting cables, refer to the

outdoor unit installation manual.• Install a remote controller following the manual supplied with the remote controller.

(3)-1 Power supply examples(3)-1-1 Us�ng MA Remote controller (Remote controller �s opt�onally ava�lable)• Connect the “1” and “2” on unit TB15 to a MA remote controller. (Non-polarized 2-wire) [Fig. V. 1. (3). 1] MA Remote controller

TB3

M1M2

(A) (B)

(C)TB15TB5

SM1M2 1 2

(A) Outdoor unit(B) PWFY-P200VM-E1-AU(C) MA remote controller

• DC 10 to 13 V between 1 and 2 (MA remote controller) [Fig. V. 1. (3). 2] MA Remote controller

• The MA remote controller cannot be used at the same time or interchangeably.

Note:Ensurethatthewiringisnotpinchedwhenfittingtheterminalboxcover.Pinchingthewiringmaycutit.

Caution:• Use wire with supplemental insulation. • Input to TB142A, TB142B, and TB142C should not carry voltage.• Cables from equipment connected to external input/output should have supplemental insulation. • Use a single multiple-core cable for external input/output to allow for connection to the PG screw.

Caution:Wirethepowersupplysothatnotensionisimparted.Otherwisedisconnection,heatingorfireresult.

2

S

M2

M1

(A)

(B)

(D)

(E)

1

LN

DC10~13V

A B1 2

(C)

(A) Non-polarized (B) TB15 (MA remote controller cables)(C) MA remote Controller(D) TB5 (Transm�ss�on cables)(E) TB2 (Power supply w�r�ng)

PWFY- P200VM-E1-AU

Page 43: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 36 -

(4) Transm�ss�on cable spec�f�cat�ons(4)-1 Transm�ss�on cables

(5) Connect�ng electr�cal connect�ons

*1 Connected with simple remote controller. CVVS, MVVS: PVC insulated PVC jacketed shielded control cable CVV, MVV : PVC insulated PVC sheathed control cable CPEVS : PE insulated PVC jacketed shielded communication cable

Type of cable

Cable diameter Remarks

Transm�ss�on cables

Shielding wire (2-core)CVVS, CPEVS or MVVS

More than 1.25 mm2

-

MA Remote controller cables

Sheathed 2-core cableCVV (unshielded)

0.3 ∼ 1.25 mm2 (0.75 ∼ 1.25 mm2)*1

Max.length: 200 m

External �nput

Sheathed multi-core cableCVV or MVV (unshielded)

0.3 ∼ 0.5 mm2

Max.length: 100 m

External output

Sheathed multi-core cable (unshielded)CVV or MVV

0.3 ∼ 1.25 mm2

Rated voltage: L1-N: 220 ∼ 240 VRated load: 0.6 A

PWFY-P200VM-E1-AU

Note:Ensurethatthewiringisnotpinchedwhenfittingtheterminalboxcover.Pinchingthewiringmaycutit.

Caution:Installwiringsothatitisnottightandundertension.Wiringundertensionmaybreak,oroverheatandburn.• F�x power source external �nput/output l�ne w�r�ng to control box by us�ng buffer bush�ng for tens�le force to prevent

electric shock. (PG connection or the like.) Connect transmission wiring to transmission terminal block through the knockout hole of control box using ordinary bushing.

• After wiring is complete, make sure again that there is no slack on the connections, and attach the cover onto the control box in the reverse order removal.

[Fig. IV. 1.(5).2]

(A) Screws(B) Front panel(C) Control box

(A) To prevent external tens�le force from apply�ng to the w�r�ng connect�on sect�on of power source term�nal block use buffer bushing like PG connection or the like.(B) External s�gnal �nput cable(C) External s�gnal output cable(D) Power source w�r�ng(E) Tens�le force(F) Use ordinary bushing(G) Transmission cable and MA remote controller cable

(A) (C)

(B)

(C)

(A)(A)

(A)

(B)

(D)

(E)

(G)

(F)

Verify that the model name on the operating instructions on the cover of the control box is the same as the model name on the nameplate.Step 1Remove the screws holding the terminal box cover in place. [Fig. V.1.(5).1]

Caution:Wirethepowersupplysothatnotensionisimparted.Otherwisedisconnection,heatingorfireresult.

Page 44: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 37 -

(6) Indoor unit address setting(Be sure to operate with the main power turned OFF.) [Fig. V. 1.(6).1] <Address board>

SWU2 SWU3SWU1

(6)-1 Rule of setting address

AG-150AGB-50ADA 000, 201 ~ 250

10 1100

0,2 0~5 0~9

PAC-YG50ECA 000, 201 ~ 250

10 1100

0,2 0~5 0~9

BAC-HD150 000, 201 ~ 250

10 1100

0,2 0~5 0~9

Settings are made on the initial screen of AG-150A.

Settings are made with setting tool of BM ADAPTER.

Unit

PWFY unit

ME, LOSSNAYRemote controller(Main)

ME, LOSSNAYRemote controller(Sub)

Address setting

01 ~ 50

101 ~ 150

151 ~ 199, 200

NoteExample

The smallest address of indoor unit in the group + 100

The place of "100" is fixed to "1"

ON/OFF remote controller 000, 201 ~ 250

Loca

l rem

ote

cont

rolle

rS

yste

m c

ontro

ller

The address of main remote controller + 50

The address automatically becomes "200" if it is set as "00"

LMAP02-E 201 ~ 250

1

1

Fixed

Fixed

2Fixed

Outdoor unit(Heat source unit)

51 ~ 99, 100

The smallest address of indoor unit in same refrigerant system + 50 Please reset one of them to an address between 51

and 99 when two addresses overlap. The address automatically becomes "100" if it is set

as "01~ 50"

Use the most recent address within the same group of indoor units.

(Note1)

0 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

10 1

0 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

10 1

10 1

0 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

0 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

10 1

0 1 2 3 4 5 6 7

8

90 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

10 1100

10 1

0 1 2 3 4 5 6 7

8

9 0 1 2 3 4 5 6 7

8

9

Note1: To set the address to "100", set it to "50"

Page 45: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 38 -

(6)-2 System examples

PWFY-P200VM-E1-AUwithPUHY-P300YJM-AorPQHY-P300YHM-Aoutdoorunit(heatsourceunit)

(6)-2-1 MA remote controller, Multi-refrigerant-system, System Controller at TB7 side, Booster for long M-NET w�r�ng

1. Address should be set to Indoor units, LOSSNAY and central controller.

2. M-NET power is supplied by the Outdoor unit (heat source unit) at TB3, while Indoor unit and MA consume the M-NET power for transmission use. The power balance is needed to consider for long M-NET wiring.

NOTE:

PWFY-P200VM-E1-AU

WMA

*2 System controller should connect to TB7 at Outdoor and use power supply unit together in Multi-Refrigerant-System.

10TB5 TB15

TB15

PWFY-P200VM-E1-AU

WMA MA

4341 42 45TB15 5BT5BT

LOSSNAY

5BT5BT

SRU

Wireless R/C

*1

*1

*1 For Wireless R/C and Signal receiver unit (SRU), channel 1, 2 and 3 are selectable and should be set to same channel.

Group 32 33 puorG

13 puorG

7BT7BT

TB3

201

PSU

*2

51

OC

PUHY-P300YJM-APQHY-P300YHM-A

[SW4-7 ON] [SW4-7 OFF]

SC

TB3

91

OC

PUHY-P-YSJMPQHY-P-YHM

CN41CN40 CN4104NC

ONDipSW2-1

ONDipSW2-1

Page 46: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 39 -

•ExternalanaloginputUse the supplied connector. If no temperature settings are made via the MA remote controller, the temperature changes with the current of generator.

ExternaloutputterminalExternal output terminal (refer to Fig. V. 1.(7).2) is ineffective when the circuit is open. Refer to Table V. 1.(7).1 for information about each contact. The current and voltage in the circuit to be connected to external output terminal (TB141A OUT1) must meet the following conditions.

Contact rat�ng currentContact rat�ng voltage

AC250V 1A or lessAC125V 3A or lessDC30V 3A or less

ExternalinputterminalThe piping length must be within 100 m.External input terminal (refer to Fig. V. 1.(7).3) is ineffective when the circuit is open. Refer to Table V. 1.(7).2 through Table V. 1.(7).4 for information about each contact.Only the “pump interlock” function is ineffective when the circuit is short-circuited.Connect a relay circuit to the external output terminal as shown in Fig. IV. 3.(10).2.The specifications of the relay circuit to be connected must meet the following conditions. Contact rating voltage >= DC15VContact rating current >= 0.1AM�n�mum appl�cable load =< 1mA at DC[Table V. 1.(7).2] TB142A [Table V. 1.(7).4] TB142C

[Table V. 1.(7).3] TB142B

*1 PWFY-P200VM-E1-AU Heating*2 Effective when SW 4-3 is set to ON.*3 Effective when SW 4-4 is set to ON.*4 PWFY-P200VM-E1-AU only*5 When Heating ECO mode is effective, the outlet water temp. will be changed based on ambient temp. automatically. (Except for PQHY-series)*6 When Anti-freeze mode is effective, the unit will set the heating temperature range between 10ºC~45ºC enabl�ng the un�t to ma�nta�n low water temperature to prevent water pipes from freezing.

Note: When setting Heating ECO or Anti-freeze mode, reset all power supply of all units (outdoor/indoor units).Note:DipS/W1-1OFF:WaterInletTemp.DipS/W1-1ON:WaterOutletTemp.ThefactorysettingforDipSW1-1isOFF.Signal priority = External input > centralized controller > remote controller

(7) External �nput/output funct�onPresettemperatureinput(externalanaloginput:4mA-20mA)•ExternalinputInput through CN421, CN422 on the circuit board. (Fig. V. 1.(7).1)

OUT1OUT2OUT4

Operat�on ON/OFFDefrost

Error s�gnal

IN1 Pump �nterlock

IN3IN4

Connection demandOperat�on ON/OFF

[Fig. V. 1.(7).1]

[Fig. V. 1.(7).3]

[Fig. V. 1.(7).2]

OUT4OUT3OUT2

TB141A

OUT1

IN1 IN2 IN3 IN4 IN5IN6 IN7 IN8

TB142CTB142BTB142A

COM+

CN

421

(BK

)(B

U)

CN

422

3

2

2

1

1

3

CN

421

(BK

)

(BU

)C

N42

2

32

+

21 13

currentdirection

Current generator

Externalanalog �nput

+

currentdirection

COM+IN5 *1IN6 *2IN7 *3IN8 *4

CommonHot Water/Heat�ng

Heat�ng ECO *5Ant�-freeze *6

Cool�ng operat�on

Method Input T(A), T(B)4mA :T(A)20mA:T(B)

S/W default T(A)=10°C T(B)=70°C.

*All setting with a controller.

T(B)°C

T(A)°C

4mA 20mAla

Conversion equation:To=[{T(B) - T(A)}/16] × Ia + [ T(A) - {T(B) - T(A)}/4] To: set temperature, Ia: analogue input value (mA)

Calculation example: T(A)=30°C, T(B)=70°C, Ia=10mAConversion equation: To=2.5 × Ia+20 To=45°C

Changeable with PAR-W21MAA

[Table. V. 1.(7).1]

Page 47: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 40 -

1.PAR-W21MAAspecificationsFUNCTION

ON/OFF

Operation mode switching

Water temperature setting

Preset temperature range

Water temperature display

Permit / Prohibitlocal operation

Weekly scheduler

Error

Self check (Error history)

Test run

Circulating waterreplacement warning

LANGUAGE setting

Operation locking function

Runs and stops the operation of a group of unitsSwitches between Hot Water / Heating / Heating ECO / Anti-freeze / Cooling* Available operation modes vary depending on the unit to be connected.* Switching limit setting can be made via a remote controller.Temperature can be set within the ranges below. (in increments of 1°C or 1°F)Hot Water 30°C ~ 70°C Heating 30°C ~ 55°C Heating ECO 30°C ~ 55°CAnti-freeze 10°C ~ 45°C Cooling 10°C ~ 30°C * The settable range varies depending on the unit to be connected.Preset temperature range setting can be limited via a remote controller.10°C ~ 90°C(in increments of 1°C or 1°F)* The settable range varies depending on the unit to be connected.Individually prohibits operations of each local remote control function :ON/OFF, Operation modes,water temperature setting, Circulating water replacement warning reset.* Upper level controller may not be connected depending on the unit to be connected.ON / OFF / Water temperature setting can be done up to 6 times one day in the week.(in increments of a minute)When an error is currently occurring on a unit, the afflicted unit and the error code are displayed.Searches the latest error history by pressing the CHECK button twice.Enables the Test run mode by pressing the TEST button twice.* Test run mode is not available depending on the unit to be connected.Displays the circulating water replacement warning via the unit message.Clears the display by pressing the CIR.WATER button twice.* Circulating water replacement warning is not available depending on the unit to be connected.The language on the dot matrix LCD can be changed. (Seven languages)English/German/Spanish/Russian/Italian/French/SwedishRemote controller operation can be locked or unlocked.·All-switch locking·Locking except ON/OFF switch

Item Description Operations Display

Controller VI

Page 48: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 41 -

2.Dipswitchfunctions

Switch FunctionFunction according to switch setting

Switch setting timingOFF ON

SW1

1 T

Operation after power recovery *1

Operation after power recovery

H0 thermistor selection Water inlet thermistor TH6 Water outlet thermistor TH8 Before power on

Before power on

Before power on

2 - - - -

3 Remains stopped

Depends on the SW1-3 setting

Auto recovery (to the status before power failure)

Forced to operate

*1 Valid only when SW1-4 is set to OFF

4

5 - - - -

6 - - - -

6 - - - -

7 Test-run mode OFF ON Any time

8 Error history deleted Normal Deleted Any time

Brine mode *2 EffectiveIneffective Any time

9Effective only when SW1-7 is set to ON and only on the HEX models.

Heating Cooling Any time

10

SW2 1-10 For self-diagnosis/operation monitoring - - Any time

SW3

1 - 8HP

2 Service LED display selection Display in Centigrade Display in Fahrenheit Any time

3 - -

-

- -

-

4 - - - -

5 Cumulative compressor opera-tion time is deleted. Normal Deleted Any time

6

7 - - - -

8 - - - -

9

10 - - - -

SW4

1

2

3Use to change pr

Do not change from factory setting.

Do not change from factory setting.

eset tempera-ture range for the Heating ECO mode.

Ineffective 30°C to 55°C Before power on

4Use to change pr

Pump interlock operation During Thermo-ON or Thermo-OFF During Thermo-ON only Any time

Any timeHeating Thermo OFF differential change *3

eset tempera-ture range for the Anti-freeze mode.

Ineffective 10°C to 45°C Before power on

5 - - - -

7 - - - -

8 - - - -

9 - - - -

10 - - - -

SW5

1 Error detection enabledEnabling/disabling ACCT sensor error detection

Error detection disable(No load operation is possible)

Any time

2 - - - -

3 - - - -

4 - - - -

*2 Refer to P32*3 The following changes can be made by changing the setting of the switch from OFF to ON.

0.5 1 0.5 2 0.5 3 0.5 4 0.5 5 0.5 6 0.5 7 0.5 8

Page 49: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

- 42 -

1.Routinemaintenancechecks• Periodically and thoroughly check the circulating water circuit. (See table below.)• Consult a maintenance technician.

2.PartsReplacementCycle

Components

Refrigerant circuit

components

Electric circuitparts

What to look for Maintenance cycle(times/year) Replacement cycle

Compressor

Water-refrigerant heat exchangerSolenoid valve(PWFY-P200VM-E1-AU)Check valve(PWFY-P200VM-E1-AU)Linear expansion valveStrainerCapillary tubePipes

Electromagnetic contactor

Overcurrent relay

Relay

Solenoid valveFuseElectronic boardSwitchPressure switchTerminal blockCable/connectorFanMotor

High/low pressure, vibration, noiseInsulation resistance, loose terminalsHigh/low pressure, water pressure loss

Operation, leakage, clogging

Operation, leakage, clogging

OperationInlet/outlet temperature differenceContact wear, VibrationContact wear, VibrationCorroded contact, loose terminalsInsulation resistanceloose terminalsOperation, Contact resistance.Insulation resistanceInsulation resistanceExternal appearanceExternal appearanceOperation, Contact resistance.Contact resistance.loose terminalsLooseness, corrosion, and wearingBalanceInsulation resistance, noise, vibration

20,000 hours

10 Years

7 Years

10 Years 7 Years

While in heavy use10 Years10 Years

8 Years

7 to 10Years

6 Years

7 Years8 Years8 Years8 Years

7 to 10Years8 Years10 Years10 Years

6 to 10Years

2

2

2

1

2111

2

2

2

222222222

Regular preventive maintenance and parts replacement help keep the unit running smoothly and minimize problems. The table below shows the maintenance schedule. Use the replacement timing in the table only as a guide. Some parts may need to be replaced sooner, depending on the usage.

MaintenanceCycle VII

Page 50: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks
Page 51: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks
Page 52: MODEL PWFY-P200VM-E1-AU - For high temperature … · since refrigeration is heavier than the air. - - • Do not install the unit where combustible gas may leak. - If the gas leaks

DATA BOOK PWFY-P200VM-E1-AU- For high temperature flow

MEE12K005A

New publication effective Feb. 2013Specifications subject to change without notice

HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Eco Changes is the Mitsubishi Electric Group’s environmental statement, and expresses the Group’s stance on environmental management. Through a wide range of businesses, we are helping contribute to the realization of a sustainable society.

WarningDo not use refrigerant other than the type indicated in the manuals provided with the unit and on the nameplate.- Doing so may cause the unit or pipes to burst, or result in explosion or fire during use, during repair, or at the time of disposal of the

unit.- It may also be in violation of applicable laws.- MITSUBISHI ELECTRIC CORPORATION cannot be held responsible for malfunctions or accidents resulting from the use of the wrong

type of refrigerant.

http://Global.MitsubishiElectric.com