Single Handle Lavatory Faucet With Pop-up

3 Hole or Single Hole Installation

Model No. : 192-5889 Polished Chrome 192-5890 Brushed Nickel 192-5891 Oil-Rubbed Bronze

Rev 01/29/15

1

2

3

4

5

6

7

910

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19 Allen Key

Aerator Wrench

Index

Screw

Aerator

Bolt

Locknut

Clamp

Putty Plate

Deck Plate

O-ring

Body

Cartridge

Cartridge Locknut

Trim Cap

Handle

Copper tube

Part NameNo.

5

Screwdriver

20

21

22

232425

26

27

29 30

28

31

32

11

12

13

14

15

16

17

8

18

19Flange

Locknut

Drain Body

Lift Rod

Extend Rod

Horizontal Rod

Rod Guide Nut

Top Rubber Washer

Bottom Rubber Washer

Drain Stopper

Washer

Tailpiece

Rod Ball Plastic Gasket

Fittings

20

21

22

23

24

25

26

27

28

29

30

31

32

Copper tube

Plumber's Putty

14

A. B. C.

Install With Deck Plate

Install Without Deck Plate

12

13

14

16

17

1.Position the faucet, deck plate 13 and putty plate 14 in order on the

countertop as shown. Don't forget the o-ring 12 .

2.Fix the faucet with clamp 16 and locknut 17 , and tighten the locknut with

basin wrench. But DON'T OVER TIGHTEN.

Add silicone under faucet to prevent leaks.(Optional)

1.Position the faucet in order on the countertop as shown. Don't forget the

o-ring 12 .

2.Fix the faucet with clamp 16 and locknut 17 ,and tighten the locknut with

basin wrench.But DON'T OVER TIGHTEN.

1216

17

Warning:

The supply valves and

supply lines are not

included, please

purchase them at a

plumbing supply store.

t

32

rod guide nut 30rod ballplasticgasket 29

drainstopperhole

drainbody 26

o-ring

sink

drain stopper 20

flange 21

align hole in drain stopperwith guide rodopening(pointed towardback wall)

flange 21

drain body 26

top rubber washer 22

sink base

locknut 25

washer 24 bottomrubberwasher 23

tailpiece 27

A. Insert lift rod 11 through hole

on faucet body.

B.Connect extend rod 32 to lift

rod 11 .Attach horizontal rod 28

to extend rod 32 using fittings 31,

tighten screw.

lift rod 11

faucetbody

extend rod 32

horizontal rod 28

screw

fittings 31

A. Replace pop-up drain stopper 20

to drain body 26 with o-ring

in place, and align stopper hole

with guide rod opening.

A. Remove rod guide nut 30 and

rod ball plastic gasket 29 .

B. Insert horizontal rod 28 into

drain body 26 and through hole

in drain stopper 20.

C. Replace rod guide nut 30 with

rod ball plastic gasket 29 and

tighten it.

horizontal rod 28

drainbody 26

A. Remove pop-up drain stopper 20.

and flange 21 with top rubber

washer 22 for pop-up assembly.

B. Insert drain body from underneath

of sink drain hole.Replace flange 21

and top rubber washer 22 back to

drain body 26.Tighten flange as far

as possible. Remove 22 and put

silicone along bottom of 21 .(Optional)

C. Slide bottom rubber washer 23

on drain body up against bottom

of sink. Tighten washer 24 and

locknut 25 firmly against base

for tight seal.

D.Remove tailpiece 27 from drain

body 26 ,add Teflon tape,replace

tailpiece 27.