MODEL DESCRIPTION DATE PRINTED PAGE PLSL DSFP · detail drawing index for security door ... model...

DETAIL DRAWING

INDEXFOR

SECURITYDOOR

LOUVERS

MODEL DESCRIPTION DATE PRINTED PAGEPLSL. . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum Security and Impact . . . . . . . . . . . . . . . . . . . . . March 2012 . . . . . . . . . . . 1FLDL-UL-SG1 . . . . . . . . . . . . . . . . . . Fire Rated Fusible Link with Security Grille One Side . . . . . March 2012 . . . . . . . . . . . 2FLDL-UL-SG2 . . . . . . . . . . . . . . . . . . Fire Rated Fusible Link with Security Grilles Two Sides. . . . March 2012 . . . . . . . . . . . 3DSFP . . . . . . . . . . . . . . . . . . . . . . . . . . Security Grille Face Plate. . . . . . . . . . . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 4DSFP-Perf . . . . . . . . . . . . . . . . . . . . . Perforated Security Grille Face Plate. . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 5Fasteners for Security Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . July 2011 . . . . . . . . . . . . 6

MARCH 2012SECURITY DOOR LOUVERS INDEX PAGE A

TECHNICAL DATAFROM

D o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219

PH: 210.662.6300 • FAX: 210.662.2828e-mail: [email protected] • website: www.anemostat.com

PLSL is not fire rated.

MATERIAL: #304 or #316 Stainless Steel, #4 Finish(Satin), Galvanized (Hot

FINISH: Custom Baked Enamel Colors (as per sample chip, supplied by customer).FASTENERS: Special Security Screw Fasteners, See 6, this section.

Dipped or Zinc Plated). Not Available in Galvanized Coil.

SPECIALS: Fractional sizes (frame dimension is increased to accommodate odd sizes).Mesh insect screens are loose, attached or framed.(Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.)

MATERIAL: 12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame with 13/16 (21mm) square holes on 1" (25mm) centers. 20 ga. (1mm) Cold Rolled Steel - Louver Blades.FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: By drilling 1/4" (6mm) holes thru the door, around the

perimeter of the door cutout. Frame has countersunk mounting holes for #8x32 phillips head thru bolts (standard) or one way vandal proof security screws (must specify) with a blank head on one side for flush appearance.

DOOR THICKNESS: For 1 3/4" (44mm) Wood or Metal Doors. Can be used in door thicknesses over 1-3/8" (35mm).

USES: For use where air flow is required in a security or Vandal resistant application.

1 3/8" MIN(35mm) 3/32"

(2mm)

1 1/16"(27mm)

3/8"(10mm)

FRAMEO.D.

ORDE

R SIZE

PLUS

2" (5

1mm)

ORDE

R SIZE

MINU

S 1/8"

(3mm

)

For detail drawings see page 12 & 13, Louver section. Refer to model FDLS.

FREE AIR FLOW: 50% Free Area.

12 GA. (2.5mm) C.R.S.FRAME / SECURITYGRILLE FACE PLATEWITH 13/16" (21mm)SQ. HOLES ON 1" (25mm) CTRS

OUTSIDE INSIDE

12 GA. (2.5mm) SECURITY

GRILLEORDER

SIZE&

DOORCUTOUT

NOTE: For Exterior use, High Humidity or Salt Air application,product must be Galvanized or Stainless Steel.

IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.

Anemostat manufacturing dimensions ±1/32 (1mm)Actual dimensions are nominal and may varybased on component manufacturers tolerances.

PLSLLOUVER WITH SECURITY GRILLE

NON-VISIONINVERTED SPLIT Y

STANDARD PRODUCT FEATURES OPTIONAL FEATURES

FIRE RATINGS

NOT FIRE RATED

HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and

ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 36" x 72" (914mm x 1829mm)

Florida Building CodeHurricane ApprovalFILE #FL11757

HURRICANE RATINGS

UNDERWRITERS’LABORATORIESFILE #R26087

Job Name & Location Submitted by

For Most Current Info, Consult Factory or check our website, www.anemostat .comMARCH 2012

SECURITY DOOR LOUVERS PAGE 1

TECHNICAL DATAFROM

DETAIL DRAWING



20/45/60/90 MINUTE: Approved listing

MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized

FINISH: Custom Baked Enamel Colors (as per sample chip supplied by customer).FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional sizes not available.SCREENS:

MATERIAL: 18 GA. (1.2mm) Cold Rolled Steel Louver Blades and Inside Frame.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Self attaching using #8 x 1" (25mm) one way vandal

proof security screws that fasten the auxiliary frame to the louver core, thru the cut out in the door. The corridor side of the frame is free of fasteners for added security.


IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.

CLOSING ASSEMBLY: Stainless steel operating springs assureproper action with the closing mechanism.

AESTHETICS: Tight mitered corners and countersunk mountingholes make for a clean appearance.

USES: In fire rated security door applications.FREE AIR FLOW: 40% Free Area.

- max width 24" (610mm), max height 24" (610mm)min width 10" (254mm), min height 6" (152mm)

(Zinc Plated). Not available in Galvanized Coil or Hot Dipped.12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame (one side only)Face Plate with 13/16 (21mm) square holes on 1" (25mm) centers.

ORDERSIZE

&DOOR

CUTOUT

ORDE

R SIZE

PLUS

2" (5

1 mm)

FRAMEO.D.

STAINLESS RIVETS

165° F (74° C) FUSIBLE LINK& HEAT SLOT

AT TOP STOPBLADE

OUTSIDEINSIDE

1"

FINGER PULL(ALWAYS ON

LOWER RIGHT HAND SIDE)

ORDE

R SIZE

MINU

S 1/8"

(3 m

m)

SPRING CLIP

3/32"(5 mm)

(25 mm)

3/4"(19mm)

Grille on two sides.Also Available with Security( )See Page 24

1 3/16"(30 mm)


12 GA. (2.5mm)C.R.S. FRAME / SECURITYGRILLE FACE PLATEWITH 13/16" (21mm) SQ. HOLES ON 1" (25mm) CTRS

DOOR THICKNESS: 1 3/4" (44mm) Door is Standard. Also available for up to2-1/2" (64mm) Door. (to maintain fire rating).

1 3/4"(44 mm)

UP TO 2-1/2" (64mm)

12 GA. (2.5mm)SECURITY

GRILLE

Mesh insect screens are loose, attached or framed. (Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.) See Louvers page 12 & 13.

DETAIL DRAWING

TECHNICAL DATAFROM

FLDL-UL-SG1FUSIBLE LINK LOUVER WITH SECURITY GRILLE ONE SIDE


FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure

MARCH 2012SECURITY DOOR LOUVERS PAGE 2

UNDERWRITERS’LABORATORIES

FIRE RATINGS


For Most Current Info, Consult Factory or check our website, www.anemostat .com



HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)

B.S.-476.22British Standard

Steel Doors - 2 hours. Tested to 610mm x 610mmBS 476.22British Standard

Florida Building Code

Hurricane Approval

FILE #FL11757

HURRICANE RATINGS


■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).

■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 24" x 24" (610mm x 610mm)

ORDERSIZE

&DOOR

CUTOUT

(MUST SPECIFY IF CUTOUT REQUIRED)


FINISH: Custom Baked Enamel Colors (as per sample chip supplied by customer).FASTENERS: Special Security Screw Fasteners, See Page 26, this section. SPECIALS: Fractional sizes not available.

MATERIAL: 18 GA. (1.2mm) Cold Rolled Steel Louver Blades and Inside Frame.

FINISH: Grey Primer, Beige or Bronze Baked Enamel.INSTALLATION: Self attaching using #8 x 1" (25mm) one way vandal

proof security screws that fasten the auxiliary frame to the louver core, thru the cut out in the door. The corridor side of the frame is free of fasteners for added security.

DOOR THICKNESS: 1 3/4" (44mm) Door is Standard. Also available up to


CLOSING ASSEMBLY: Stainless steel operating springs assureproper action with the closing mechanism.

AESTHETICS: Tight mitered corners and countersunk mountingholes make for a clean appearance.

USES: In fire rated security door applications.FREE AIR FLOW: 40% Free Area.

(Zinc Plated). Not available in Galvanized Coil or Hot Dipped.12 GA. (2.5mm) Cold Rolled Steel Security Grille Frame (two sides)Face Plate with 13/16 (21mm) square holes on 1" (25mm) centers.

ORDE

R SIZE

PLUS

2" (5

1 mm)

FRAMEO.D.

STAINLESS RIVETS

STOPBLADE

for 2-1/2" (64mm) Door. (to maintain fire rating).

OUTSIDEINSIDE

1"

FINGER PULL(ALWAYS ON LOWERRIGHT HAND SIDE)OPTIONAL CUTOUT

IN FACE GRILLETO ASSIST

FINGER PULL OPERATION

ORDE

R SIZE

MINU

S 1/8"

(3 m

m)

SPRING CLIP

Grille on one side onlyAlso Available with Security

See Page 233/32"

(5 mm)

(25 mm)

1 9/16"(40 mm)

( )


12 GA. (2.5mm) C.R.S.TWO SIDES FRAME / SECURITY GRILLE FACE PLATE W/ 13/16" (21mm) SQ. HOLES ON 1" (25mm) CTRS

12 GA. (2.5mm)SECURITY

GRILLE

20/45/60/90 MINUTE: Approved listing

SCREENS:

- max width 24" (610mm), max height 24" (610mm)min width 10" (254mm), min height 6" (152mm)

Mesh insect screens are loose, attached or framed. (Galvanized, Aluminum, Charcoal Aluminum, Stainless Steel.) See Louvers page 12 & 13.

165° F (74° C) FUSIBLE LINK& HEAT SLOT

AT TOP

1 3/4"(44 mm)

UP TO 2-1/2" (64mm)

IMPORTANT: Interpretation of building and fire codes may vary. Consult with the local authority having jurisdiction in your area, to determine appropriate standards.

DETAIL DRAWING

TECHNICAL DATAFROM


FIRE RATINGS (w/ U.L. & W.H.I. classification markings) Positive Pressure

MARCH 2012SECURITY DOOR LOUVERS PAGE 3





Steel Doors - 2 hours. Tested to 610mm x 610mmBS 476.22British Standard

FLDL-UL-SG2FUSIBLE LINK LOUVER WITH

SECURITY GRILLE TWO SIDES

UNDERWRITERS’LABORATORIES

FIRE RATINGS

B.S.-476.22British Standard

Florida Building Code

Hurricane Approval

FILE #FL11757

HURRICANE RATINGS


HURRICANE TEST / WINDSTORM APPROVALS (W/ U.L. MARKING)■ Successfully tested in accordance with ASTM E1886, E1996 and E330 and

ANSI 250.13-Impact 350 FT LBS. Design Pressure: +/- 70 PSF (large missile test).■ Complies with Florida Building Code Standards■ Maximum size for hurricane use is 24" x 24" (610mm x 610mm)


For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2011


ORDER SIZE WIDTH

Anemostat manufacturing dimensions ±1/32Actual dimensions are nominal and may varybased on component manufacturers tolerances.

DSFP is not fire rated.


FINISH: Custom Baked Enamel Colors (as per sample chip,

FASTENERS: Special Security Screw Fasteners, See Page 26, this section.


(Hot Dipped or Zinc Plated). 10 gauge or 7 gauge.

supplied by customer).

SPECIALS: Fractional sizes, and other face plate patterns.

MATERIAL: 12 GA. Cold Rolled Steel Lattice Face Plate SecurityGrille (with 13/16" square holes on 1" centers.)

FINISH: Grey Primer, Beige or Bronze Baked Enamel.

#8X1" one way vandal proof security screws, thatcan be screwed directly thru the face plate

INSTALLATION: Frame has countersunk mounting holes for

into wall or door.DOOR OR WALL THICKNESS: Will work on any thickness based

FREE AIR FLOW: 66% Free Area.

3/8"(10mm)

13/16" (21mm) SQUARE HOLESON 1" (25mm) CENTERS

3/16"(5mm)

#8X1" ONE WAY VANDAL PROOF SECURITY SCREWS (HOLE LOCATION AND QUANTITY WILL VARY BY SIZE)

12 GA. STEEL(7/64")

on ability to accept a screw or fastener.

IMPORTANT: Interpretation of building and fire codes may vary.Consult with the local authority having jurisdiction inyour area, to determine appropriate standards.

FRAME O.D.

OPENING AREAORDER SIZE LESS 2 3/16" (56mm)

OPENING AREAORDER SIZE LESS 2 3/16" (56m

m)

1 3/32"(27mm)

ORDERSIZE

HEIGHT

FRAMEO.D.

(3mm)

TECHNICAL DATAFROM

DETAIL DRAWING

DSFPSECURITY GRILLE

FACE PLATE


FIRE RATINGS

NOT FIRE RATEDD o o r P r o d u c t s

4958 Stout Dr. #119, San Antonio, TX 78219PH: 210.662.6300 • FAX: 210.662.2828

e-mail: [email protected] • website: www.anemostat.com

JULY 2011SECURITY DOOR LOUVERS PAGE 5





All Dimensions ±1/32

12 GA. STEEL (7/64")(3mm)

FRAME O.D.ORDER SIZE WIDTH

FRAMEO.D.

ORDERSIZE

HEIGHT

* 1-3/16" (30mm) BORDER IS APPROXIMATE. THIS DIMENSION IS A

#8 x 1" ONE WAY VANDAL PROOF SECURITY SCREWS (HOLE LOCATION AND QUANTITY WILL VARY BY UNIT SIZE)

FUNCTION OF SIZE AND PERFORATED PATTERN.

1 3/16" *(30mm)

5/16" (8mm) DIAM. HOLESON 7/16" (11mm) STG. CTRS.

1 3/16" *(30mm)

OPENING AREAORDER SIZE LESS 2 3/8" (60mm)

OP

EN

ING

AR

EA

OR

DE

R S

IZE

LES

S 2 3/8 (60m

m)

3/8"(10mm)

TECHNICAL DATAFROM

DETAIL DRAWING

DSFP-PerfPERFORATED

SECURITY GRILLEFACE PLATE


FIRE RATINGS

NOT FIRE RATED

■ MATERIAL: 12 GA. Cold Rolled Steel Perf. Face Plate Security Grille (with 5/16" diam. holes on 7/16" stag. ctrs.)

■ FINISH: Grey Primer, Beige or Bronze Baked Enamel.■ INSTALLATION: Frame has countersunk mounting holes for #8 x 1" One Way

Vandal Proof Screws that can be screwed directly thru theface plate into the wall or door.

■ FREE AIR FLOW: 46% Free Area.■ NOTE: For Exterior use, High Humidity or Salt Air application, product must

be Galvanized or Stainless Steel.■ IMPORTANT: Interpretation of building and fire codes may vary.

Consult with the local authority having jurisdiction in yourarea, to determine appropriate standards.

■ MATERIAL: #304 or #316 Stainless Steel, #4 Finish (Satin), Galvanized (Hot Dipped or Zinc Plated). 10 gauge or 7 gauge.

■ FINISH: Special order Baked Enamel Colors (as per sample chip, supplied bycustomer).

■ FASTENERS: Special Security Screw Fasteners Available.■ SPECIALS: Fractional sizes, and other face plate patterns. Consult Factory.

Can be fabricated without screw holes.

■ DSFP-Perf is not fire rated.


For Most Current Info, Consult Factory or check our website, www.anemostat .comJULY 2011


#8X32 THRU BOLT, BLANK ONE ENDUSED FOR ALL MODELS: SG-10, SG-12, SL-IS, FGS, PLSL AND BR-7

*Screwdrivers and insert bits for Security Fasteners are available.Consult Factory for Price and Availability.

ONE WAY VANDALPROOF SECURITY SCREW#8X1" USED FOR: DSFP, FLDL-UL-SG1, FLDL-UL-SG2#8X3/4" USED FOR: SG-10-SSD, SSD#8X1-3/4" USED FOR: LoPro-SC, LoPro-GR, LoPro-SC-GR, LoPro-SSD

3/8"

STANDARD

NOTCHED SPANNERHEAD SCREW

TORX-PLUS FLAT HEADSECURITY SCREW

(Available on all Security Products)

SECURITY SCREWTORX FLAT HEAD SOCKET

SNAKE EYE SPANNERFLAT HEAD SECURITY SCREW(DRILLED SPANNER)

PINNED FLAT HEAD CAP SCREW(TAMPER RESISTANT HEX SOCKET)

ONLY AVAILABLE ONCERTAIN APPLICATIONS

OPTIONAL SECURITY FASTENERS*

1/4"X20 THRU BOLT BLANK ONE END-MEETS ASTM F-1450-97 (MUST SPECIFY): SG-10, BR-7, SG-12-SP, SG-10-SP, SG-12-LSC

TECHNICAL DATAFROM

DETAIL DRAWING

FASTENERSFOR

SECURITY VISION FRAMESAND

SECURITY DOOR LOUVERSD o o r P r o d u c t s4958 Stout Dr. #119, San Antonio, TX 78219


MODEL DESCRIPTION DATE PRINTED PAGE PLSL DSFP · detail drawing index for security door ... model...

Documents

Transcript of MODEL DESCRIPTION DATE PRINTED PAGE PLSL DSFP · detail drawing index for security door ... model...