Model Code : SP-KR 1/2HP 4P MITSUBISHI SUPER … 05...Model Code : SP-KR 1/2HP 4P Full Load Current...
1
Model Code : SP-KR 1/2HP 4P Full Load Current (A) Full Load Speed (r/min) Starting Current (A) Starting Torque (%) 1440 1730 200 161 34 34 293 251 4.8 4.6 Motor Characteristics Dimensions (mm) 80 125 97 50 146.6 62.5 3.2 153.3 92 130 165 10 10 50 D C* A B F E G H KL N M Z X XB Motor Bearing No. Drive End Opposite 6203ZZ 6202ZZ Approximated Weight (kg) Gross Weight (kg) Approximated Packing Dimensions (LxWxH) 11 300 x 200 x 184 12 Circumstance Conditions 85% RH or less o -20 ~ +40 C No bursting / erosive gas or vapor Less than 1,000m above sea level Specifications subject to change without notice. Specifications MITSUBISHI SUPER LINE SERIES INDUCTION MOTOR Ambient Temperature Ambient Humidity Operating Altitude Environment * The perpendicular variation of tolerance for the shaft center is 0 -0.5 Connection & Connection Diagram Connection Connection Diagram Open-Protection IP 20 Steel plate M A SW M Horizontal Class E (120 °C) Alignment Frame Material Degrees of Protection Enclosure Construction Thermal Class 1 Phase 1/2 (0.4) 4 Pole 80M Drilling Machine, Blower Munsell N5.5 (Gray) IEC 60034-1 & JEC-2137-2000 Voltage & Frequency 220~230V 50Hz 220V 60Hz Motor Split Phase Start Output Power HP (kW) Phase Pole Frame Number 44.5 12 12 KA KD2 KD1 Break Down Torque (%) Hz 50 60 Power Supply 1 Phase 220V Starting Method Application : : : Main Coil Auxiliary Coil Centrifugal Switch A SW Torque r/min Connection Type Coating Colour Conformed Standard Terminal Block 265 L Q 40 QK 28 R 140 S 16 j6 Shaft End T 5 U 3 W 5 L A R KA B Q QK KD1 F F N E G C H E M D KL X Frame foot as viewed from below Sliding distance Z KD2 U Outlet of lead S XB W T Outline Drawing Characteristic Curve Circuit Connection Class E (120 °C) IEC 60034-1 & JEC-2137-2000 220~230V 50Hz 220V 60Hz
Transcript of Model Code : SP-KR 1/2HP 4P MITSUBISHI SUPER … 05...Model Code : SP-KR 1/2HP 4P Full Load Current...
Model Code : SP-KR 1/2HP 4P
Full LoadCurrent
(A)
Full LoadSpeed(r/min)
StartingCurrent
(A)
StartingTorque
(%)
1440
1730
200
161
34
34
293
251
4.8
4.6
Motor Characteristics
Dimensions (mm)
80125 97 50146.6 62.5 3.2 153.3 92
130165 1010 50
DC*A B FE G H KL
NM ZX XB
Motor
Bearing No.
Drive End Opposite
6203ZZ 6202ZZ
ApproximatedWeight (kg)
GrossWeight (kg)
Approximated PackingDimensions (LxWxH)
11 300 x 200 x 184 12
Circumstance Conditions
85% RH or less
o-20 ~ +40 C
No bursting / erosive gas or vapor
Less than 1,000m above sea level
Specifications subject to change without notice.
Specifications
MITSUBISHI SUPER LINE SERIES INDUCTION MOTOR
Ambient Temperature
Ambient Humidity
Operating Altitude
Environment
* The perpendicular variation of tolerance for the shaft center is0
-0.5
Connection & Connection Diagram
Connection
Connection Diagram
Open-Protection
IP 20
Steel plate
MASW
M
Horizontal
Class E (120 °C)
Alignment
Frame Material
Degrees of Protection
Enclosure ConstructionThermal Class
1 Phase
1/2 (0.4)
4 Pole
80M
Drilling Machine, Blower
Munsell N5.5 (Gray)
IEC 60034-1 & JEC-2137-2000
Voltage & Frequency 220~230V 50Hz220V 60Hz
Motor
Split Phase Start
Output Power HP (kW)
Phase
Pole
Frame Number44.5 1212
KA KD2KD1
Break DownTorque
(%)Hz
50
60
PowerSupply
1 Phase 220V
Starting Method
Application
:::
Main CoilAuxiliary CoilCentrifugal Switch
A
SW Torq
ue
r/minConnection Type
Coating Colour
Conformed Standard
Terminal Block
265
L Q
40
QK
28
R
140
S
16 j6
Shaft End
T
5
U
3
W
5
L
A
R
KA
B Q
QK
KD1
FF
N
E
G CH
E
M
D
KL
X
Frame foot asviewed from below
Slidingdistance
Z
KD2
UOutlet of lead S
XBWT
Outline Drawing
Characteristic CurveCircuit ConnectionClass E (120 °C)
IEC 60034-1 & JEC-2137-2000
220~230V 50Hz220V 60Hz
