Model 3086 ipRocketLink IAD Basic Configuration
description
Transcript of Model 3086 ipRocketLink IAD Basic Configuration
Model 3086ipRocketLink IAD
Basic Configuration
22April 22, 2023 Model 3086 IAD Basic Configuration
After this Presentation You Will Be Able to:
1. Configure the ipRocketLink Serial Port via DIP switches
via Web Management
2. Configure the ipRocketLink for Dual Serial/Ethernet Network Access
Objectives
33April 22, 2023 Model 3086 IAD Basic Configuration
Outline
Product Overview Typical applications
Bridged Ethernet Extension Routed Network Access Serial (Simple Modem) Access Dual Serial/Ethernet access
Key Features
Configuring for Basic Operation
Two Examples: Serial-to-DSL Modem Dual Serial/Ethernet Access
Installing DTE/DCE Connections DIP Switch Configuration Plug-In, Power-Up, Log-In Setting the IP Address Firing Up a Browser
44April 22, 2023 Model 3086 IAD Basic Configuration
Typical Applications (Ethernet Only)
BridgedEthernet
Extension
SubNet 1
G.SHDSLSubNet 1
RoutedNetworkAccessSubNet 2
G.SHDSLSubNet 1
3096RCG.SHDSL T-DAC
T1/E1WAN
Uplinks
55April 22, 2023 Model 3086 IAD Basic Configuration
Typical Applications (Serial)
G.SHDSL V.35 or X.21
Serial Network Access(Simple Modem)
V.35 or X.21
T1/E1WAN
Uplinks
Aggregated Network Access(Dual Serial/Ethernet)
G.SHDSL
Ethernet
66April 22, 2023 Model 3086 IAD Basic Configuration
DSL Bandwidth Allocation for Dual Access
Seria
l Dat
a St
ream
Map
s to
Hig
h-
Num
bere
d Ti
mes
lots
. . . | 18 | 1 | 2 | . . . |18| 1 | . . .Serial Line
18 Timeslots X 64 kbps = 1152 Kbps
. . . | 36 | 1 | 2 | . . . | 18 | 19 | 20 | . . . | 36 | 1 | . . . G.SHDSL Line
36 Timeslots X 64 kbps = 2.048 Kbps*
* Current maximum DTE rate. A future release will support 4.608 Mpbs.*
. . . | 18 | 1 | 2 | . . . | 18 | 1 | . . .Ethernet Line
18 Timeslots X 64 kbps = 1152 KbpsEthernet Data Stream
Maps to Low-
Numbered Timeslots
77April 22, 2023 Model 3086 IAD Basic Configuration
Product Overview – Key Features
G.SHDSL Speeds up to 4.6 Mbps* on
just one twisted pair!
VT-100 Console Port for CLI/SNMP Management
AC or DC Power Options
10/100 Ethernet Port with Full-
Duplex Operation
Web Browser Configuration &
Management
Proven Patton Design
Convenient Built-InMDI-X Crossover
Switch
13 Front-Panel LEDs Provide Operational Status-at-a-Glance
*Supported in future release. Current maximum data rate is 2.304 Mbps.*
IntegratedV.35 or X.21Serial Port
DUALEthernet + Serial
Access
Test ModeToggle Switches
ETSI/ITU G.SHDSL G.991.2
Standard
88April 22, 2023 Model 3086 IAD Basic Configuration
Your ipRocketLink’s Ethernet Port will connect to a LAN Your ipRocketLink’s Serial Port will connect to a Router Your ipRocketLink’s Line (DSL) Port will connect to a
DSL Line, which is connected to either . . . Users via a remote IAD Provider Network DSLAM such as the ForeFront 3096RC
Assumptions
Ethernet LAN
DSL Line
Remote Users
Your ipRocketLink
or
2-Wire Copper Twisted PairT1/E1WAN
Uplinks
99April 22, 2023 Model 3086 IAD Basic Configuration
Making Connections
ipRocketLink InterfacesConsole Port(Command Line
Interface)
Ethernet Port(LAN Connection)
DSL Port(G.SHDSL Connection)
PowerSupply
Connector
Ethernet LAN
2-Wire DSL Line
V.35 or X.21 or T1/E1Serial Port
1010April 22, 2023 Model 3086 IAD Basic Configuration
Overview: Setup & Configuration
Installing DTE/DCE Connections DIP Switch Configuration Plug-In, Power-Up, Log-In Setting the IP Address Firing Up a Browser
Configuring for Basic OperationTwo Examples: Serial-to-DSL Modem Dual Serial/Ethernet Access
Two Stages . . .
1111April 22, 2023 Model 3086 IAD Basic Configuration
X.21 Port DTE/DCE Configuration
X.21 Port
DTE/DCE Jumper
(J7)
3. Turn it around.4. Replace the jumper.
Factory Default: ipRocketLink Configured as DCE
1. Open the case with a screwdriver to access the jumper.
Configurable via “jumper.” To configure x.21 port for DTE:IAD X.21 Port
3086 IADDCE
V.35 DTE
3086 IADDCE
V.35DCE
CrossoverCable
Straight-ThroughCable
NOT configurable. Use crossover cable.IAD V.35 Port
2. Remove the jumper.
1212April 22, 2023 Model 3086 IAD Basic Configuration
Configuring the Serial Port via DIP Switches
DIP-Switch-Configurable Parameters Annex A or Annex B Serial Port Data Rate
CO or CP Operation Internal or External Clock
Model 3086Bottom ViewF
RONT
REAR
Factory Default: All Switches ON
1313April 22, 2023 Model 3086 IAD Basic Configuration
DIP Switch Configuration (2)
Configuring Switch Bank S2Switch Bank 2
Switch Activation – S2-8 Toggle Switch On-Off-On to Activate Switch Configuration
Serial Port Data Rate Switches S2-1 – S2-7
S1 S2 S3 S4 S5 S6 S7 Data Rate
Off Off On On On On On 192 On On Off On On On On 256 Off On Off On On On On 320 On Off Off On On On On 384
. . . . . .
. . . . . .
. . . . . .
. . . . . .
On Off On On Off On On 1152 . . .
. . . . . .
. . . . . .
. . . . . .
. . . On On On On On Off On 2048 Off On On On On Off On 2112 On Off On On On Off On 2176 Off Off On On On Off On 2240
1414April 22, 2023 Model 3086 IAD Basic Configuration
DIP Switch Configuration (3)
Annex A or Annex BS3-6
Annex B = ON (Up)Annex A = Off (Down)
CO or CP OperationS3-1
CO = ON (Up)CP = Off (Down)
Internal or External ClockS3-3
External = ON (Up)Internal = Off (Down)
Switch Bank S3
Configuring Switch Bank S3
1515April 22, 2023 Model 3086 IAD Basic Configuration
You will configure the ipRocketLink’s IP address using a computer workstation with Terminal Emulation software connected to the ipRocketLink’s Console port.*
More Assumptions
You will configure the ipRocketLink for basic operation using a computer workstation with Web Browser software via an Ethernet LAN connected to the ipRocketLink’s Ethernet Port.
*Ethernet Port may also be used for this task.
1616April 22, 2023 Model 3086 IAD Basic Configuration
Preparing for Installation
Model 3086 G.SHDSL IAD
You Will Need . . .
*Installation kit shipped with the IAD includes these items*
Ethernet straight-through cable* (with RJ45 plugs on each end)
DB9-to-RJ45 Adapter*
Appropriate Serial Cable (V.25/X.21/WAN)
External power supply*
1717April 22, 2023 Model 3086 IAD Basic Configuration
Preparing for Installation (continued . . .)
You Will Also Need . . . ASCII Terminal or . . . Computer Workstation with Terminal Emulator
Ethernet Hub or Switch*
* (Optional) To connect multiple user devices to the ipRocketLink.
1818April 22, 2023 Model 3086 IAD Basic Configuration
Preparing for Installation (continued . . .)
Web Browser SoftwareYou Will Want . . .
IP Address on the same LAN as your computer workstation
192.168.110.229
Existing IP Address
(Factory Default)
1919April 22, 2023 Model 3086 IAD Basic Configuration
Plugging In (to the Console Port*)
1. Connect the DB9-RJ45 adapter to the workstation’s DB-9 serial port.
2. Connect one end of the RJ45-RJ45 straight-through cable to the adapter.
3. Connect the other end of the cable to the ipRocketLink’s RJ45 Console port.
* Do NOT connect the IAD to the Ethernet LAN yet*
2020April 22, 2023 Model 3086 IAD Basic Configuration
Plugging In (continued . . .)
4. Start a HyperTerminal session
2121April 22, 2023 Model 3086 IAD Basic Configuration
Powering Up
1. Power up the IADConnect power supply to the ipRocketLink power connectorPlug power supply into an AC power source
. . . Perform activationCLI startedCLI OS-specific initLogin:
AC PowerSource
You will see a sequence of boot messages ending with . . .
2222April 22, 2023 Model 3086 IAD Basic Configuration
Powering Up: LED Indicators
AC PowerSource
Power Green ON indicates that power is applied. Off indicates that no power is applied. WAN (DSL) Link Green Solid green: connected Off: disconnected Sync Serial TD Green Green: indicates a binary ‘0’ condition off: indicates a binary ‘1’or idle condition RD Green Green: indicates a binary ‘0’condition off: indicates a binary ‘1’ or idle condition CTS Green ON: indicates the CTS signal from the IAD is active, binary ‘1’ off: indicates CTS is binary ‘0’ DTR Green ON: indicates the DTR signal from the DTE device attached to the serial port is
active, binary ‘1’ Ethernet Link Green ON: indicates an active 10/100 BaseT connection 100M Green ON: connected to a 100BaseT LAN Off: connected to a 10BaseT LAN Tx Green lashing: when transmitting data from the IAD to the Ethernet Rx Green Flashing: when transmitting data from the Ethernet to the IAD. Status NS Red ON: incidates absence of a valid DSL connection ER Red flashes once: indicates bit errors occurring during 511/511E tests TM Yellow ON: is under one of the test modes (local loop, remote loop, or V.54 BER pattern)
2323April 22, 2023 Model 3086 IAD Basic Configuration
Logging In
1. Type “admin” for login and press [Enter]
2. Type “admin” for password and press [Enter]
Login:adminPassword: *********Login successful-->
2424April 22, 2023 Model 3086 IAD Basic Configuration
Setting the IP Address (1)
1. Type “ip list interfaces” [Enter]to display the current configuration . . .
ip list interfaces <enter>IP Interfaces: ID | Name | IP Address | DHCP | Transport-----|--------------|------------------|----------|---------------- 1 | ip1 | 192.168.200.10 | disabled | <BRIDGE>-------------------------------------------------------------------
Existing IP Address(Factory Default)
2525April 22, 2023 Model 3086 IAD Basic Configuration
Setting the IP Address (2)
ip set interface ip1 ipaddress 192.168.110.229 255.255.255.0 <enter>
ip list interfaces <enter>IP Interfaces: ID | Name | IP Address | DHCP | Transport-----|--------------|------------------|----------|---------------- 1 | ip1 | 192.168.110.229 | disabled | <BRIDGE>-------------------------------------------------------------------
2. Type the command line as shown, using your chosen IP Address and netmask . . .
Enter Your NewChosen IP Address Here
2626April 22, 2023 Model 3086 IAD Basic Configuration
Setting the IP Address (3)
ID | Name | IP Address | DHCP | Transport-----|--------------|------------------|----------|---------------- 1 | ip1 | 192.168.110.229 | disabled | <BRIDGE>------------------------------------------------------------------- system config save <enter> system config save Wait for 'configuration saved' message...Saving configuration... Configuration saved.
3. STORE! your newly modified configuration.***
*** Otherwise the ipRocketLink will LOSE your newIP Address when it is powered down!***
2727April 22, 2023 Model 3086 IAD Basic Configuration
Plugging In . . . Again
1. Disconnect the PC from the ipRocketLink’s Console Port.
Ethernet hub or switch
2. Connect a straight-through Ethernet cable between the PC’s NIC or PCMCIA Ethernet card and an Ethernet hub or switch.
X
2828April 22, 2023 Model 3086 IAD Basic Configuration
Plugging In . . . Again
2. Connect an Ethernet cable between the ipRocketLink’s Ethernet Port and an Ethernet hub or switch.*
192.168.110.229192.168.110.230
PC & ipRocketLink must be on same subnet
Ethernet Hub or Switch
*(Optional) If multiple users will connect to the ipRocketLink.
Use MDI-X Switch for convenient
straight-through / crossover
conversion
2929April 22, 2023 Model 3086 IAD Basic Configuration
Firing Up a Browser
1. On your PC, launch a standard web browser such as Netscape Communicator or Internet Explorer.
2. In the Address (URL) field of the browser, enter the ipRocketLink’s IP address.
3030April 22, 2023 Model 3086 IAD Basic Configuration
Firing Up a Browser (continued . . .)
ipRocketLink Web Management Home Page Displays . . .
ipRocketLink Installation is now completed.
http://192.168.110.229
3131April 22, 2023 Model 3086 IAD Basic Configuration
Logging In for Web Management
ipRocketLink Login Pop-Up Window
Enter “superuser” for User Name. Enter “superuser” for password.
Click the“OK”
button.
3232April 22, 2023 Model 3086 IAD Basic Configuration
ipRocketLink Web Management PageConfiguration Menu Pane Management Information Pane
3333April 22, 2023 Model 3086 IAD Basic Configuration
Configuring for Operation (1)
Serial & G.SHDSL Ports . . .
G.SHDSL V.35 or X.21
Serial Network Access(Simple Modem)
V.35 or X.21
T1/E1WAN
Uplinks
Aggregated Network Access(Dual Serial/Ethernet)
G.SHDSL
Ethernet
3434April 22, 2023 Model 3086 IAD Basic Configuration
Configuring the G.SHDSL Attributes
1. Click G.SHDSL,then Configuration2. Select Parameter values appropriate for your application . . .
2304k
DSL Rate
Serial Line Rate
ATM or HDLC
Ethernet, Serial or both
3. Click Configure.
3535April 22, 2023 Model 3086 IAD Basic Configuration
Configuring for Operation (2)
Ethernet Port . . .BridgedEthernet
Extension
SubNet 1
G.SHDSLSubNet 1
RoutedNetworkAccessSubNet 2
G.SHDSL
SubNet 1
3096RCG.SHDSL T-DAC
T1/E1WAN
Uplinks
3636April 22, 2023 Model 3086 IAD Basic Configuration
Configuring for Operation
Understanding Your Application . . .
3737April 22, 2023 Model 3086 IAD Basic Configuration
Bridged Application Protocols
ATMHDLCTwo Choices: Pick One.
Transport Protocols
High-level Data Link Control Asynchronous Transfer Mode
SubNet 1
G.SHDSLSubNet 1
3838April 22, 2023 Model 3086 IAD Basic Configuration
Bridged Application Protocols (continued…)
Three Combinations: Pick One.
Encapsulation (PDU Type)
PPPoHPoint-to-Point Protocol
overHigh-level Data Link Control
PPPoAPoint-to-Point Protocol
overAsynchronous Transfer Mode
RFC 1483 Multiprotocol
over Asynchronous Transfer Mode
ATMHDLCPPP Multiprotocol (RFC 1483)
SubNet 1
G.SHDSLSubNet 1
3939April 22, 2023 Model 3086 IAD Basic Configuration
Routed Application Protocols
Transport Protocols
ATMHDLCEthernet
Three Choices: Pick One.
SubNet 2
G.SHDSLSubNet 1
T1/E1WAN
Uplinks
4040April 22, 2023 Model 3086 IAD Basic Configuration
Routed Applications Protocols (continued…)
Encapsulation (PDU Type)
ATMHDLCEthernetPPP Multiprotocol
(RFC 1483)IP
Five Combinations: Pick One.
PPPoE PPPoH PPPoA IPoAInternet Protocol
over ATM
RFC 1483 Multi-Protocol
over ATM
SubNet 2
G.SHDSLSubNet 1
T1/E1WAN
Uplinks
4141April 22, 2023 Model 3086 IAD Basic Configuration
Configuration ExamplesConfiguring for Operation
BridgedEthernet
Extension
SubNet 1
G.SHDSLSubNet 1
Example One
Example Two
SubNet 2
G.SHDSLSubNet 1
T1/E1WAN
Uplinks
RoutedNetworkAccess
4242April 22, 2023 Model 3086 IAD Basic Configuration
Example OneConfiguring for Operation
BridgedEthernet
Extension
SubNet 1
G.SHDSLSubNet 1
4343April 22, 2023 Model 3086 IAD Basic Configuration
Configuration: Example One
Bridged Ethernet Extension Using PPPoH
ipRocketLink (Central)IP: 192.168.110.229/24
User AIP: 192.168.110.11/24Gateway: 192.168.110.229
ipRocketLink (Remote)IP: 192.168.110.230/24
User BIP: 192.168.110.12/24
Gateway: 192.168.110.230/24
SubNet 1
G.SHDSLSubNet 1
4444April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (1)
1. Click Configuration then WAN Connections
3. Click Create a new service...
2. Delete the factory defaults
4545April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (2)
4. Click PPPoH bridged
3. Click the configure button
4646April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (3)
5. Enter a description for the WAN connection (optional).
6. Verify the parameter values match those shown.
7. Click the Apply button.
4747April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (4)
The WAN link is now Configured.
Next: Defining G.SHDSL Attributes . . .
4848April 22, 2023 Model 3086 IAD Basic Configuration
Defining G.SHDSL Attributes (1)
1. Click G.SHDSL then Configuration
4949April 22, 2023 Model 3086 IAD Basic Configuration
Defining G.SHDSL Attributes (2)
3. For Interface Typeselect hdlc.
2. For Terminal Type select Central.*
You must configure the ipRocketLink at the other end of the G.SHDSL link as “Remote”.
4. Click the Configure button.
*
5. Click the Action submenu.
5050April 22, 2023 Model 3086 IAD Basic Configuration
Activating the G.SHDSL Port
7. Click the Action button.
6. Select Deactivate.
6. Click the Action button again.
The Action drop-down menu will automatically return to a value of Start.
ipRocketLink G.SHDSL Port is now activated.
5151April 22, 2023 Model 3086 IAD Basic Configuration
Basic Configuration: Example One (completed)
Bridged Ethernet Extension Using PPPoH
ipRocketLink (Central)192.168.110.229/24
User AIP: 192.168.110.11/24Gateway: 192.168.110.229/24
ipRocketLink (Remote)192.168.110.230/24
User BIP: 192.168.110.12/24
Gateway: 192.168.110.230/24
ipRocketLink (Central) is now Configured.
Repeat the proceduresfor ipRocketLink (Remote)
SubNet 1
SubNet 1
5252April 22, 2023 Model 3086 IAD Basic Configuration
Example TwoConfiguring for Operation
RoutedNetworkAccessSubNet 2
G.SHDSLSubNet 1
3096RCG.SHDSL T-DAC
T1/E1WAN
Uplinks
5353April 22, 2023 Model 3086 IAD Basic Configuration
SubNet 2
SubNet 1
T1/E1WAN
Uplinks
Configuration Example Two
Routed Connection to DSLAM Using PPPoA (RFC 2364)
ipRocketLink (Remote)IP: 192.168.110.229
UserIP: 192.168.110.11Gateway: 192.168.110.229
DSLAM (Central)IP: 192.168.120.230
CO Uplink to InternetIP: 192.168.130.0
G.SHDSLPPPoA RoutedWAN Service
SubNet 3
WAN Gateway Address192.168.120.230
WAN PortIP: 192.168.120.231
5454April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (1)
1. Click Configuration then WAN Connections
3. Click Create a new service...
2. Delete the factory defaults
5555April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (2)
4. Click PPPoA Routed
3. Click the configure button
5656April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (3)
5. Enter a description for the WAN connection (optional).
6. Define parameter values to match those shown.
8. Click the Configure button.
7. Define a User name & Password for User Authentication.
119.168.120.231
5757April 22, 2023 Model 3086 IAD Basic Configuration
Defining PPP Attributes (1)
1. Click Edit...
2. Click Edit ‘PPP’
5858April 22, 2023 Model 3086 IAD Basic Configuration
Defining PPP Attributes (2)
3. Define parameter values to match those shown.
255.255.255.0
255.255.255.0
5959April 22, 2023 Model 3086 IAD Basic Configuration
Defining PPP Attributes (3)
4. For Version Enabledselect true.
5. Click the Change button.
6060April 22, 2023 Model 3086 IAD Basic Configuration
Defining the ATM Channel
1. Click Edit ‘Atm Channel’
2. Define parameter values to match those shown.
3. Click the Change button.
6161April 22, 2023 Model 3086 IAD Basic Configuration
Defining the IP Interface
1. ClickEdit ‘IP Interface’
2. Define parameter values to match those shown.
3. Click the Change button.
6262April 22, 2023 Model 3086 IAD Basic Configuration
Defining the Wan Connection (completed)
The WAN link is now Configured.
Next: Defining G.SHDSL Attributes . . .
6363April 22, 2023 Model 3086 IAD Basic Configuration
Defining G.SHDSL Attributes (1)
1. Click G.SHDSL then Configuration
6464April 22, 2023 Model 3086 IAD Basic Configuration
Defining G.SHDSL Attributes (2) (continued . . .)
3. For Interface Typeselect Atm.
2. For Terminal Type select Remote.
4. Click the Configure button.
5. Click the Action submenu.
6565April 22, 2023 Model 3086 IAD Basic Configuration
Activating the G.SHDSL Port
7. Click the Action button.
6. Select Deactivate.
6. Click the Action button again.
The Action drop-down menu will automatically return to a value of Start.
6666April 22, 2023 Model 3086 IAD Basic Configuration
SubNet 2
SubNet 1
T1/E1WAN
Uplinks
Basic Configuration: Example Two (completed)
Routed Connection to DSLAM Using PPPoA (RFC 2364)
ipRocketLink (Remote)IP: 192.168.110.229
UserIP: 192.168.110.11/24Gateway: 192.168.110.229 CO Uplink to Internet
IP: 192.168.130.0
G.SHDSL PPPoA RoutedWAN Service
SubNet 3
ipRocketLink (Remote) is now Configured.
WAN PortIP: 192.168.120.231Gateway: 192.168.120.230
Model 3086Basic Configuration
(END)