MOBILE LABORATORY OF WATER LEAK DETECTION … SPECS.pdf · LEAK DETECTION AquaLAB ... Specially...

Holding company ”EMZ” Head office and Factory:

Aradippou Industrial and Commercial Estate, Larnaca, Cyprus

RN HE 132211; IN 9.84 Number ФПА (VAT) 10132211L

For letter: P.O. Box 41016 6308 Larnaсa, Cyprus

Phone: + 357 24821788 secretary Fax: + 357 24821787

E-mail: [email protected] Internet: www.vitaldrive.net

MOBILE LABORATORY OF WATER LEAK DETECTION

AquaLAB

In most water-distribution systems and pipelines, a large percentage of the water is lost in transit from treatment plants to consumers. Factors that contribute to this loss are old and poorly constructed pipelines, inadequate corrosion protection, poorly maintained valves and mechanical damage. Our water leak detection test van is a cost-effective way to conserve water, save lost revenue, and control unnecessary costs. Early detection of leaks reduces the possibility of public health risks and the potential for major property damage. Utilizing state-of-the-art equipment the water leak detection test van is capable of locating and exposing the exact location of hidden underground water leakages. Further, our investigative procedures are non invasive/non destructive and can detect and identify the damage locations without digging or trenching.

LABORATORY FEATURES:

Determines the pipeline route of a water

supply network;

Checks up valves and gates for the

presence of leakages;

Measures the water flow in a section of

the pipeline;

Pinpoints the place of water leakages;

Stores data for graphing, processing and

later analysis.







A. ACCURATE PINPOINTING OF UNDERGROUND FLUID LEAKS

Advanced system for the accurate pinpointing of underground fluid leaks, prior to excavation Eureka2. The system has been proven to perform world-wide and can be used effectively on all types of pipe – not only metallic, but also plastic and asbestos cement. Benefits: Fast and simple, enabling rapid leak location Optimum correlation performance Palm-top size and weight Rugged construction for routine operations Fast-Track or Advanced operation. Eureka 2R can be used in two modes – Fast-Track or Advanced. The Fast-Track mode can be used quickly and reliably, involving only three operations for basic leak pin-pointing. The Advanced mode incorporates features such as unwanted noise suppression, velocity calculation, filter adjustment, display zoom and saving results.

The correlation display is shown directly as distance (unlike most correlators where a display of time-delay is used). This has the benefit, particularly in multiple pipe situations, of giving a displayed result directly proportional to distance on the ground.

Features Automatic and manual filter selection Unwanted noise suppression Fast, automatic battery charging from mains

or vehicle; minimizes equipment down-time Built-in language options Software upgradeable Convenient in-case battery charger







B. ULTRASONIC FLOW METERING SYSTEM PrimeFlo is a rugged ultrasonic flowmeter utilising advanced signal transmission. PrimeFlo automatically uses both Transit-Time and Doppler measurement modes. It is for use on a wide range of pipe sizes and materials in clean and dirty water applications. Benefits

Use on pipe sizes from 10 to 2500mm (two transducers required)

Easy to install clamp-on sensors with no process interruption

Non-invasive measurement – no flow disturbance or pressure loss

Accurate and repeatable measurements even at low flows

Self powered for 24 hours

Application PrimeFlo utilises advanced digital design to meet the practical needs of engineers for measuring flow-rates and total flow at multiple points on water networks. Applications include

Water network management Minimum night-flow measurement Flow surveys Pump flow control In-situ meter validation

PrimeFlo is designed for use in harsh environments. The case is made of ruggedised ABS plastic giving ingress protection to IP67 (lid closed). Cables and sensors are protected to IP68. Programming is user-friendly via the integral keypad and display. PrimeFlo may be powered from mains or an internal rechargeable battery. This has an operational life of 24 hours which makes it suitable for temporary flow monitoring. It connects easily to the full range of Primayer data loggers.







Features: Dual mode Transit Time and Doppler Real-time display of flow-rate, total flow

and sound velocity Accuracy to ±0.5% or ±0.02m/s

whichever is the greater (with process calibration)

Integral data logger or connection to Primayer data loggers

Portable, lightweight and easy to use Data imported into PrimeWorks software

for graphing, processing and storage Outputs for process control interfacing Mains power or battery operation Wall thickness gauge

C. ACOUSTIC LEAK DETECTION SYSTEM Phocus 2 is an intelligent acoustic data logger system designed for widespread use in detecting and localizing leakage on water distribution systems. Large areas may be rapidly assessed. Phocus2 gives visual, on-site indication of leakage or can be used with sophisticated software to produce graphical and tabular results. Phocus2 advantages:

Rapid, overnight, identification of leaks - without the need for staff night working

Use for survey or permanent operation Large areas can be covered quickly Intelligence built into logger for instant,

on-site, indication of leakage Advanced analysis PC software

Operation Leak pre-location is carried out by installation of a number of Phocus2 loggers at available fittings such as hydrants or valves. The loggers record leak noise during the night, when background noise is likely to be lower. Noise amplitude will vary due to random effects, but there will always be a consistent minimum (the critical noise level) due to any constant noise – for example, leakage.







Loggers which are situated closer to a leak will record a higher critical noise level. The leak can then be pinpointed (usually by using the leak noise correlation technique). The System The Phocus2 system consists of a number of acoustic noise loggers. A communications case is required to program and readback loggers. The case has the contact-less communications facility built into the lid. Loggers may be placed in any position and the PC software automatically identifies each logger. The case provides for communication for up to 15 loggers at the same time and the cases may be connected to build a system with any number of loggers.

Visual indication provides instant on-site awareness of the leakage situation.

Logger Features

Specially optimized accelerometer with high sensitivity

Large memory - stores up to one year of noise data

Powered for life (5 - 10 years) Small size - only 90mm high Submersible (to IP68) Rapid, contact-less communications to

multiple loggers

Data Analysis The sophisticated PC software automatically identifies each logger and enables the simple programming and read-back of multiple loggers. The results are displayed as two or three dimensional graphs of the characteristic noise and provide easy to interpret analysis. Additionally, a table ranks logger position relative to the leak position.







D. PRECISION PIPE LOCATOR The Cable Avoidance Tool (CAT) is a full function, industry standard locator which every ground working operative will find familiar and easy to use. It is rugged, lightweight and full of features.

LCD meter - precision locating as standard

Detachable loudspeaker - held next to the ear in noisy work situations

Fingertip controls - adjust sensitivity and rapid switching between the locator’s three operating modes

Two models available

Standard model XD model with depth indication

Advantages

Visual Display provides greater precision and offers improved operation for accurate direction and splitting close signals

Spare battery pack included Constant battery level indicator Customer replaceable speaker assembly

SPECIFICATION CSCAT-33 Cable Avoidance Tool Controls On/Off control, activated when in use Three position function switch: P - POWER mode for live, imbalanced cables R - RADIO mode for re-radiated radio signals G - GENERATOR mode for detecting conductors carrying the Generator signal Detachable (user replaceable) loudspeaker User replaceable base protector Display Signal strength, battery condition, operating mode

Depth of detection Detects to the following depths: P-3 metres R-2 metres G-3 metres These values are provided for information only and performance depends on the site (terrain, temperature, humidity, etc). Batteries (not included) Type: 8 x AA (IEC type LR6) Life: 40 hours (at 20°C) Check: an audio signal indicates that the batteries have sufficient power when the receiver is first turned on. During use, a battery check facility is displayed. Weight: 3kg (including batteries) Moisture/Dust resistant: IP65







ZCSSGSGA-33 Signal Generator Enhance detect-ability of pipes and cables. Use to transmit an easily identifiable signal along a pipe or cable. The Cable Avoidance Tool uses industry accepted 33kHz frequency for clear reception.

CSCATXD-33 Cable Avoidance Tool + Depth Indication Includes features of the standard CAT with additional depth option

Depth push button: in G mode only gives a depth indication

Battery check Depth measurement Active in G Mode only Range: 0.25 –3.0m (Line) 1.0 – 6.0m (Sonde) Visual indicator Large, high accuracy, LCD with ruggedised mounting. Mounted behind a polycarbonate lens for maximum protection. Controls On/Off – Signal level rotary control Pulse/continuous selection switch Volume switch Typical tracing range Induced mode: 200 metres Direct connected mode: 350 metres Frequency: 33kHz pulsed/continuous Batteries (not included) Type: 4 x D cells (IEC type LR20) Life: 30 hours intermittent use at 20°C

E. ACOUSTIC LEAK LOCATION SYSTEM

Mikron is a high performance, simple to use leak locator. The design is based upon an advanced sensor and incorporates low-noise processing electronics to give excellent acoustic performance over a wide frequency range. Mikron incorporates a Minimum Noise Level measurement system.

Principle Mikron detects noise generated by leaks in water pipes. The leak noise travels through the water and pipe wall and can be detected by listening at valves or hydrants. Leak noise also propagates from the leak to the ground surface where it can be detected using the sensitive ground microphone.







Features Very high acoustic sensitivity Acoustic probe, ground microphone and

combined system options Advanced ground microphone with

wind-noise isolation Minimum Noise Level measurement Lightweight amplifier with clear digital

display Simple to use

Minimum Noise Level digital display To enable accurate leak pinpointing Mikron displays the Minimum Noise Level, i.e. the background noise level which will potentially include the leak noise, but without transient noises, such as road traffic. Mikron also displays the two previous Minimum Noise Level measurements such that the user can easily tell if they are moving toward or away from a leak. The current sound level, volume position and battery charge are also displayed.

Advanced amplifier The small, lightweight amplifier unit can be held in one hand. The display is easy to read and includes the following range of filters for operation in different leak location conditions.

Flexible performance In the ground microphone system the high performance sensor is suspended thus drastically reducing interference from wind or other sources of airborne noise. The acoustic probe system can be configured as an electronic listening stick or ground microphone and includes a tripod for use on hard ground, spike for use on soft ground and optional magnet. The systems are rugged and use military grade connectors for sensor and battery charging. Rechargeable batteries provide approximately 35 hours operation (without backlight).







F. LEAK SIZER SYSTEM Leak Sizer is an advanced instrument for leak location and for the determination of leak size probability.

Prioritise repairs to reduce leakage losses Reduce repair costs High sensitivity to detect quiet leaks Minimum noise level display Multiple leak noise sound recording Leak noise spectrum display

Methodology Once the leak position has been determined then the Leak Sizer operation commences. The process is as follows:

Collect 30 seconds of acoustic data from the ground surface immediately above the estimated leak position

Enter estimate of network pressure Optionally collect 30 seconds of acoustic

data from pipe fitting close to the leak such as a valve or stop tap

Results The algorithms within the Leak Sizer software then analyse this data to extract a range of key features which can be correlated probabilistically against leak size. The sizing process is divided into two categories; communication/services pipes (less than 50mm) and mains pipes (greater than 50mm). The leak size estimate probability is displayed in three categories for the smaller pipes and into two categories for the larger pipes.

Research data Leak Sizer is the result of over two years research carried out in the South West Water company in the UK. This research included measurement of over 370 actual leaks. A wide variety of pipe materials and soil types were assessed. The light blue line on the graph shows average performance, ie. what should happen if leaks are repaired in random order. The yellow line shows the Leak Sizer performance and the green line the theoretical ideal performance.







Sensor characteristics High performance accelerometer Acoustic data digitised at accelerometer Bluetooth® data transmission to PDA for

data processing Battery life 40 hours (rechargeable)

System components Advanced ground sensor with

Bluetooth® communications Large mass for constant acoustic

coupling with ground surface (for leak sizing)

Tripod attachment for surface listening (+ soft ground spike)

PDA with rugged case + Leak Sizer software

Connecting rods + handle High performance headphones

G. NOTEBOOK The notebook provides an interface for data acquisition, data analysis and data storage for the mobile laboratory of water leak detection.

H. TOOL SET Along with the test van a tool set is provided. It includes:

Electro drill with puncher 500W Hammer Butts set (5, 6, 7, 8, 9, 10, 11, 12, 13

mm) Wire cutters Flat-nose pliers Screw-driver with a set of bats Roulette 5 m. Adjustable spanner Knife Drills Hard alloy drills Hack-saw for metal

I. POWER SUPPLY

This modern gasoline generator is ideal for independent work on construction sites and for industrial, commercial or private operation. With a large fuel tank it guarantees up to 8 hours running time and offers excellent performance and at the same time it is very safe to use.







TECHNICAL SPECIFICATIONS Engine: Honda GX 390 Super

Silent Cylinder: 1 Speed: 3000 rpm Fuel: Gasoline Engine oil capacity: 1.3 l Cooling (Eng./Generator):

Air / Air

Electr. capacity 1~ φ 1.0:

6450 VA

Voltage 1~: 230 V Max. Current 1~: 28 A Current 1~ (CEE): 28 A Current 1~ (Schuko): 16 A Max. starting current cos φ 0,6:

16 A

Starting current with 20% voltage drop:

45 A

Frequency: 50hz Tank capacity: 20 I Weight: 95.5/104.5 kg incl. batt. Dimensions (L x W x H) :

740x500x530 mm

Acoustic power LWA: 97 dB(A) Acoustic pressure (10m

no load): 69 dB(A)

J. VEHICLE Chassis: The basic types of chassis used are: Mercedes Sprinter, Iveco Daily, Ford Transit etc.

Vehicle Body The mobile laboratory is designed to be easy to operate and service. It is equipped with high quality insulated wall panelling and air conditioning. The body is divided into technical and operator compartments separated by a partition wall. The technical compartment includes all the necessary tools and equipment for carrying out testing and inspections. Safety is an important







feature of the laboratories and hence all equipment is properly mounted and secured for transit. The operator compartment provides a pleasant environment to work in with more room and plenty of storage. It is equipped with cabinetry and workbenches that increase the operators’ efficiency and productivity. FEATURES

Roof mounted air conditioner Internal lighting 230 VAC & 12V DC Insulated walls and roof for thermal and noise Special PVC floor in operator area Special aluminium tread plate suitable for rough loading in technical area Partition wall, Operating desk & Swivel chair Drawers for storage of accessories

K. DOCUMENTATION Set documentation of the laboratory is included.

L. WARRANTY Our laboratories are covered by a warranty for a period of one year. At the end of this period, the manufacturer can provide upon request an after-sales service of the equipment.

Contact information: Tel.: +357 24821788; Fax: +357 24821787, Mob.: + 357 99556229, E-mail: [email protected] For letter: P.O.Box 41016, Larnaca 6308, Cyprus Factory: Aradippou Industrial and Commercial Estate, Larnaka, Cyprus www.vitaldrive.net

MOBILE LABORATORY OF WATER LEAK DETECTION … SPECS.pdf · LEAK DETECTION AquaLAB ... Specially...

Documents

Transcript of MOBILE LABORATORY OF WATER LEAK DETECTION … SPECS.pdf · LEAK DETECTION AquaLAB ... Specially...