MM5420 MM424-A Rev 020620:MM1779 Med-Lok PrPrRev 10/03
Transcript of MM5420 MM424-A Rev 020620:MM1779 Med-Lok PrPrRev 10/03
36” Cover Width
1
Multi-Rib
1.1875”
12” 12”Multi-Rib Roofs & Walls ( With Purlin Bearing Leg )
Multi-Rib Walls Only( Without Purlin Bearing Leg )
R-Panel Walls Only( Without Purlin Bearing Leg )
1.1875”
12” 12”
1.25”
36” Cover Width
R-Panel Roofs & Walls ( With Purlin Bearing Leg )
1.25”
36” Cover Width36” Cover Width
R-Panel
- Minimum slope: 1:12 (with sealant)
- Multi-Rib is also available with MoistureLok
Details:- Roof panels: purlin bearing leg required- Wall panels: non-purlin bearing leg optional
- Coating:- Kynar 500® (PVDF)- Silicone Modified Polyester (SMP)
- Substrate: - Standard 26 GA Galvalume® (roof and wall panels)- Multi-Rib: optional 24, 22 GA Galvalume (wall panels)- R-Panel: optional 24, 22 GA Galvalume (wall panels only)
Notes:- Oil canning is inherent in all metal panels and is not cause for panel rejection.- Please contact a McElroy representative for specific pricing, lead times, special colors or gauges that may not be on a
McElroy Metal color chart. - Contents in this manual are subject to change without notice. To confirm this book is the most current copy, please visit McElroyÊs
website at www.mcelroymetal.com.
Panel Options:
Multi-Rib and R-Panel Load Tables and Section Properties
For any available Test Data, Section Properties or Load Tables, please visit www.mcelroymetal.com. For additionalinformation, please contact the McElroy Engineering Department at 1-800-950-9082.
MULTI-RIB/R-PANEL
2
Multi-Cor and M-Cor Load Tables and Section Properties
For any available Test Data, Section Properties or Load Tables, please visit www.mcelroymetal.com. For additionalinformation, please contact the McElroy Engineering Department at 1-800-950-9082.
Multi-Cor M-Cor
.5”
2.67”M-Cor PanelMulti-Cor Panel
.875”
32” Cover Width for Roofing and Siding 34.67” Cover Width for Roofing and Siding
MULTI-COR/M-COR
2.67”
- Multi-Cor minimum slope: 1:12 - M-Cor minimum slope: 1:12- Tape sealant required on all slopes- Can be installed over solid deck or open framing
- Multi-Cor and M-Cor are produced in Bossier City, LA
Details:- Coating:
- Kynar 500® (PVDF)- Silicone Modified Polyester (SMP)
- Substrate: - Standard 26 GA Galvalume®
- Optional 24, 22 GA Galvalume (Multi-Cor)- Optional 29, 24 GA Galvalume (M-Cor)
Notes:- Oil canning is inherent in all metal panels and is not cause for panel rejection.- Please contact a McElroy representative for specific pricing, lead times, special colors or gauges that may not be on a
McElroy Metal color chart. - Contents in this manual are subject to change without notice. To confirm this book is the most current copy, please visit McElroyÊs
website at www.mcelroymetal.com.
Panel Options:
3
U-Panel
U-PANEL
Master Coil Width: 40 7/8” (29 GA Only) Master Coil Width: 41 9/16”
U-Panel Load Tables and Section Properties
For any available Test Data, Section Properties or Load Tables, please visit www.mcelroymetal.com. For additionalinformation, please contact the McElroy Engineering Department at 1-800-950-9082.
Master Coil Width: 43”
6” (typ.)
U-PANEL NON- PURLIN BEARING PROFILEU-PANEL NON- PURLIN BEARING PROFILE
6” (typ.)
.734375”
U-PANEL PURLIN BEARING PROFILE
6” (typ.)
36” Cover Width
36” Cover Width36” Cover Width
.734375”.734375”
- Minimum slope: 1:12 (with sealant)Details:
- Roof panels: purlin bearing leg required- Wall panels: non-purlin bearing leg optional
- Coating:- Kynar 500® (PVDF)- Silicone Modified Polyester (SMP)
- Substrate: - Standard 26 GA Galvalume®
(roof and wall panels)- Optional 29, 24, 22 GA Galvalume
(wall panels)
Notes:- Oil canning is inherent in all metal panels and is not cause for panel rejection.- Please contact a McElroy representative for specific pricing, lead times, special colors or gauges that may not be on a
McElroy Metal color chart. - Contents in this manual are subject to change without notice. To confirm this book is the most current copy, please visit McElroyÊs
website at www.mcelroymetal.com.
Panel Options:
1.1875”
12” (Nom.)
35 3/4” Cover Width
Multi-V and Mini-Rib Load Tables and Section Properties
For any available Test Data, Section Properties or Load Tables, please visit www.mcelroymetal.com. For additionalinformation, please contact the McElroy Engineering Department at 1-800-950-9082.
Mini-Rib
.375”
3”
36” Cover Width
4
Mini-Rib PanelMulti-V Panel
Multi-V
MULTI-V/MINI-RIB
- Multi-V is to be used as a wall panel only
- Mini-Rib is not applicable for exterior roof panels
- Mini-Rib is produced in Bossier City, LA
Details:- Coating:
- Kynar 500® (PVDF)- Silicone Modified Polyester (SMP)
- Substrate: - Multi-V
- Standard 26 GA Galvalume®
- Optional 24 GA Galvalume
- Mini-Rib- Standard 26 and 29 GA Galvalume®
- Optional 24 GA Galvalume
Notes:- Oil canning is inherent in all metal panels and is not cause for panel rejection.- Please contact a McElroy representative for specific pricing, lead times, special colors or gauges that may not be on a
McElroy Metal color chart. - Contents in this manual are subject to change without notice. To confirm this book is the most current copy, please visit McElroyÊs
website at www.mcelroymetal.com.
Panel Options:
Mini Jamb / Header CoverITMHJ
MULTI-RIB/R-PANEL
2 1/8”
3 1/2”
2”
1/2”
3 3/8”
3 1/2”
1/2”
3”
8 1/8”
2 7/16”
1 1/2”
1”
2 1/4”
1 1/4”
1/2”2 1/2”
1”
3”
3”
1”2 5/8”
1 3/4”
2 5/8”
Simple Base TrimITBD
Zee TrimITZF
Outside CornerITOC
Base TrimITBT
Inside CornerITIC
Masonry WainscoatITMW
Outside Angle TrimITOA
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
5
Rake Tie-In TrimITEW
Rake ClosureITREC
High Side Eave Trim*ITHS
Rake TrimITRT
Sculptured Eave Trim*ITSCE
Eave Trim*ITET
Inside Angle TrimITIA
Head TrimITHT
Jamb TrimITJT
Jamb / Head Cover TrimITHJ
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:7 ̓- 1”8 ̓- 1”9 ̓- 1”
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
3/4”1 3/4”2 3/4”
1 3/4”
1 1/2”
2”
4”
1”
1 3/4”1”
4”
1 3/4”
1 3/4”
1 3/4”
4”
4”
1”
1” 3”
3”
4”2”
1” 3 1/2”
3 1/2”
6”1 3/4”
2”
2”
2 1/2”
Color Side5 1/4”
1 3/4”
1”
1”
3 1/2”
3 1/2”
2”
6 3/4”
8 3/4”
2”
2”
3 1/2”
3 1/2”
12”*
12”*
12”*
Color SideColor Side
Color Side
Color Side
Color SideColor Side
Color Side
Color Side
Color Side
Color Side
Color Side
ColorSide
Color Side
Color Side
ColorSideUp
26 GATRIM
Color Side
*specify roof pitch
95° 85°2”
1/2”
4 1/2”
3 1/2”
Color Side
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Alternate Masonry WainscoatITAMW
1 1/2”Color Side 1 1/2”
2”
Variable Peak BoxIT-PBV
Fixed Peak Box*(Additional Roof Pitch Available)IT-PBF
6 7/8”
Color Side
MULTI-RIB/R-PANEL
2 1/2”
6 1/4”
Multi-Rib Formed Ridge Cap*MRC
R-Panel FormedRidge Cap*RRC
Lengths:1 ̓- 8”
Outside Corner Box for Standard Gutter(Right Hand Shown Left Hand Opposite)IT-OCB
Standard Gutter* 1/2:12 to 2:12 PitchITSG2
High Side Corner Box(Right Hand Shown Left Hand Opposite)ITHSCB
Ridge Cap*ITRC
High Side Tie-In Trim*ITSW
26 GA
6
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Standard Gutter End Cap(Right Hand Shown Left Hand Opposite)1/2 to 2:12 PitchITSGEC2
Standard Gutter End Cap2:12 to 4:12 PitchITSGEC4
11 1/2” 11 1/2”
12”*
12”*
12”*
12”*
12”*
1/2:12 up to 2:12 roof slopes with standard gutter.
3 1 /2”
3 1/2”
4”
5 3/8”
3/4”7/8”
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
4”
VarieswithPitch
3 1/4”1 1/4”
3 1/2”
Sculptured Gutter* up to 4:12 PitchITSCG
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Snow guards required to preventdamage caused by sliding snow.
Snow guards required to preventdamage caused by sliding snow.
4 3/8”
3 15/16”
4 15/16”
1 1/8”
3 1/2”
4 13/16”
1 15/16”
3 15/16”
2 11/16”
ColorSide Up
ColorSide Up
1”
Color Side
Color Side
Color Side Color Side
TRIM
Gutter Corner Box For Standard Gutter2:12 to 4:12 or with Sculptured Gutter(Right Hand Shown Left Hand Opposite)ITGCB
6 1/2”
1 ̓- 8”2ʼ
2ʼ
Field cut asrequired for pitch
Field cut asrequired for pitch
Field bend
10”10”
3”
4”
2”
1”
10” 8”
3”
2”2”
4”
Lengths:0 ̓- 6”
Gutter StrapIT-GS
1 5 / 1 6 ” 1 5 / 1 6 ”
1 5/8”Color Side
Color Side
15”or
18”
15”or
18”
15”or
18”
15”or
18”
12”*
VarieswithPitch
*specify roof pitch
4 3/8”
Standard Gutter* 2:12 to 4:12 PitchITSG4
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Snow guards required to preventdamage caused by sliding snow.
12”*
4”
2 3/4”
ColorSide
3 5/8”
3/4” 7/8”
5 5/8”
3 1/4”
4 1/4”
Simple Base TrimCORSB
3/4”
1”
3”
Downspout StrapBBPDSS
26 GA
7
Lengths:10 ̓- 3”
Lengths:10 ̓- 3”
3” x 4” DownspoutElbow A-StyleBBPELA
Skylight Side Trim - UL90(For Use with Multi-RIb Panels)
Skylight Side Trim - UL90(For Use with R-Panels)
Lock-Seam Downspout - Corner(Right Hand Corner Shown)
Lengths:10”
10”
Please specify left or right hand corner
8.5”
3”
9.5”
3”
3”
1 3/8”
1/2”
1 1/2”
1 3/8”
Lock-Seam Downspout - Center
4”
3 1/2”
2” 2 1/2”
Lock-Seam Downspout Outlet -Standard
Lock-Seam Downspout Strap
4 1/4”
3 3/8” 3 3/8”
3 1/2”
4”
1”1 1/2”
1”
3”
Base TrimCORBT
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Color SideColor Side
1 5/8”
1/2”
1 3/8”
1 1/8”
Color SideColor Side
Masonry WainscoatCORMW
95° 95°
Color Side
Color Side
Color Side
MULTI-RIB/R-PANELTRIM
MULTI-COR/M-CORTRIM
26 GA
Downspout 3” x 4”BBPDS
Lengths:14 ̓- 3”
14 ̓3”
4”
4”
3”
*specify roof pitch
95° 85°2”
1/2”
4 1/2”
3 1/2”
Color Side
Aluminum Downspout Outlet BBPOUT 4 3/4”
1 3/8”
Sculptured Gutter End Cap(Right Hand Shown Left Hand Opposite)ISGEC
4 3/4”
2 11/16”
3 15/16”
3 1/2”
ColorSide Up
1”
5 1/2”
5 7/8”
3 7/8”
1”
1”
1”3 3/8”
3”
Gutter StrapCOR-GS
Aluminum Downspout OutletBBPOUT
1 3/8”
1 1/2”
3 1/2”
1”4 1/4”
Rake TrimCORRT
10”
1”
3 1/2”
1/2”
3”
5/8”
4 5/8”
1”
1”
2 3/4”
7/8” 1/2”
2 1/4”
3/4”
5/8”
2 1/8”
7/8”
3”
3”
4 3/8”
5”
2 5/8”
3 7/8”5/8”
4 3/4”
Jamb Trim (Multi-Cor / U-Panel Only)CORJT
Head Trim (Multi-Cor / U-Panel Only)CORHT
Outside Angle TrimCOROA
Eave Trim*CORET
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
26 GA
8
Color Side
Color Side
Color Side
Color Side
Color Side
ColorSide
ColorSide
Color Side
Color Side
Color Side
Downspout 3” x 4”BBPDS
Gutter*CORGT
High Side Tie-In Trim*CORSW
High Side Eave Trim* CORHS
Rake-Tie-InCOREW
Ridge Cap*CORRF
Lengths:7 ̓- 1”8 ̓- 1”9 ̓- 1”
Lengths:10”
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:14 ̓- 3”
Lengths:10”
Lengths:10 ̓- 3”14 ̓- 3”
6 1/4”
2 1/2”
12”*
Lengths:10 ̓- 3”14 ̓- 3”
11 1/2” 11 1/2”
12”*
12”*
12”*
4”
5”
3” x 4” Downspout Elbow A-StyleBBPELA
4 3/4”
4 15/16”
3 7/8”
4 7/8”
3 1/2”
1 7/16”
Downspout StrapBBPDSS
Gutter End CapCORGEC
10”
8.5”
3”
9.5”
3”
3”14 ̓3”
4”
4”
3”
8 1/8”
2 7/16”
Jamb / Head Cover TrimITHJ
Color SideLengths:
10 ̓- 3”14 ̓- 3”
MULTI-COR/M-CORTRIM
12”*
*specify roof pitch
Head / Jamb Trim (M-Cor Only)MCORHJ
Lengths:10 ̓- 3”14 ̓- 3”
1” 3 1/2”
3 1/2”
5 1/4”1 1/16”
2”
2”
2 11/16”
3 1/2”
2”
1/2”
3 13/16”
3 1/2”
1/2”
3”
1”
1”
2 3/4”
7/8”
1/2”
2 1/4”
3/4”
3”
3”
1 1/16”
1 1/16”
1 1/8”
5 3/4”
3/4”
3/4”3 3/16”
1”
1 1/16” 1”
3 3/16” 1 1/16”
1”1 1/2”
1”
3”
U-PANELSimple Base TrimU-SB
Rake Tie-In TrimU-EW
Outside Angle TrimU-OA
Base TrimU-BT
Inside CornerU-IC
Masonry WainscoatU-MW
Rake TrimU-RT
Outside CornerU-OC
26 GATRIM
Zee FlashingU-ZF
Head TrimU-HT
Jamb TrimU-JT
*specify roof pitch
Eave Trim*U-EF
Sculptured Eave Trim*U-SE
9Indicates an open hem - All other hems are closed.H
Color Side Color SideColor Side
Color Side
Color Side
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
12”
*12”
*
Inside Angle TrimU-IA
Rake ClosureU-RC
3/4”
1”
3”
1”
1 3/4”
2”
Color Side
ColorSide
Color Side
Lengths:10 ̓- 3”14 ̓- 3”
Color Side
Color Side Up
Color Side
Color Side
ColorSide
3”
3”
2 7/16”
2 1/2”
1 1/16”
1” 1”
3 1/2”
3 1/2”
2”
6 3/4”
8 3/4”
2”
2”
3 1/2”
3 1/2”
Color Side
Color Side
Color Side
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
2 1/2”
6 1/4” Lengths:10 ̓- 3”14 ̓- 3”
11 1/2” 11 1/2”
Ridge Cap*U-RC
High Side Eave Trim*U-HS
High Side Tie-In Trim*U-SW
12”
*12”
*12”
*
95° 85°2”
1/2”
4 1/2”
3 1/2”
Color Side
Formed Ridge Cap*URC
12”
*
4”
6 7/8”
3 1/4”
5”
7/8”
3 1/2”
GutterU-GT
Sculptured GutterU-SG
*specify roof pitch10
Indicates an open hem - All other hems are closed.H
Color Side
Gutter End CapUGEC5
Gutter End CapSculpturedUGECT
DownspoutBBPDS
TRIM
Lengths:10 ̓- 3”14 ̓- 3”
Color Side
Color Side
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:14 ̓- 3”
3 1/2”
3 1/2”
4”
5 7/8”
5/8”7/8”
Gutter StrapU-GS
Lengths:0 ̓- 6”
15/16”
1 1/8”
4 9/16”
3 5/16”
3 15/16”
3 7/16”
6” ColorSide Up
ColorSide Up
1”
4 7/8”
3 15/16”
4 13/16”1 5/8”
3 7/16”
14 ̓3”
4”
4”
3”
Aluminium Downspout OutletBBPOUT
4 3/4”
1 3/8”
26 GA
Fixed Peak Box*(Additional Roof Pitch Available)U-PB
6 7/8”
Color Side
Lengths:1 ̓- 8”
Outside Corner Box for Standard Gutter(Right Hand Shown Left Hand Opposite)U-OCB
High Side Corner Box(Right Hand Shown Left Hand Opposite)U-HSC
12”*
1/2:12 up to 2:12 roof slopes with standard gutter.
Gutter Corner Box For Standard Gutter2:12 to 4:12 or with Sculptured Gutter(Right Hand Shown Left Hand Opposite)U-GCB
6 1/2”
3 1/4”
1 ̓- 8”10”
10”
3”
4”
2”
1”
10” 8”
3”
2”2”
4”
A-Style ElbowBBPELA 3”
8.5”
3”9.5”
3”
Downspout StrapBBPDSS
10”
U-PANEL
18” 18”
45°
4 1/4”
Masonry WainscoatITMW
1 1/2”
1”
2 1/4”
1”2 5/8”
1 3/4”
2 5/8”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Base TrimITBT
Multi-V Outside CornerMUVOC
Outside Angle TrimITOA
Head TrimITHT
Jamb TrimITJT
Inside Angle TrimITIA
Simple Base TrimITBD
11
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
3/4”
1 3/4”
2 3/4”
5 1/2”
5 1/2”
1”
1”
1 3/4”
1 3/4”
3”
3”
3”
3”
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
Outside Angle TrimITOA
Inside Angle TrimITIA
3”
3” 3”
3”
26 GA
Color SideColor Side
Color Side
Color Side
Color Side
Color Side
Color Side
Color Side
Color Side
8 1/8”
2 7/16”
Jamb / Head Cover TrimITHJ
Lengths:10 ̓- 3”14 ̓- 3”
Lengths:10 ̓- 3”14 ̓- 3”
MULTI-VTRIM
TRIM
*specify roof pitch
1 1/4”
1/2”2 1/2”
1”Color Side
95° 85°2”
1/2”
4 1/2”
3 1/2”
Color Side
Lengths:10 ̓- 3”14 ̓- 3”20 ̓- 3”
Alternate Masonry WainscoatITAMW
1 1/2”Color Side 1 1/2”
2”
MINI-RIB
1/4 - 14 x 1 1/4”TEK2 ZAC Self-Driller(Part # varies by color)
#12 - 14 x 1 1/4”TEK2 HWH w/washerSelf-Driller(Part # varies by color)
1/4 - 14 x 7/8”LAPTEK HWH w/washerSelf-Driller(Part # varies by color)
43D Pop rivets(Part # varies by color)
#14 x 1 1/2”Type AB ZAC(Part # varies by color)
Touch-Up Paint Pen(Part # varies by color)
Roll Tape Sealant3/32” X 1” X 45ʼItem #: 95335
White Urethane SealantItem #: 95320
Titebond Caulk Sealant(Part # varies by color)
Multi-V Outside Closure95099
Multi-Rib Inside ClosureWith Adhesive: 95058Without Adhesive: 95054
Multi-Rib Outside ClosureWith Adhesive: 95059Without Adhesive: 95057
Multi-V Inside Closure95097
Mini-RIb Closure95151
R-Panel Inside ClosureWith Adhesive: 81886Without Adhesive: 95080
R-Panel Outside ClosureWith Adhesive: 81887Without Adhesive: 95085
M-Cor Closure95011
Multi-Cor Closure95031
12
1/4 - 14 x 7/8”LAPTEK ZAC Self-Driller(Part # varies by color)
ACCESSORIES
Butyl Tube SealantItem #: 95342
Images not drawn to scale.
Roll Tape Sealant1/8” x 1” x 30ʼItem #: 95345
MULTI-RIB / R-PANEL / MULTI-CORM-COR / U-PANEL / MULTI-V / MINI-RIB
#9 - 15 Type A WoodgripW/Washer(Part # varies by color)
Lengths:1”
1 1/2”2”
2 1/2”
#10 - 15 WoodgripHILO ZAC(Part # varies by Color)
#12 - 14 x 1 1/4”TEK2 ZACSelf-Driller(Part # varies by color)
Notes:
Lengths:8ʼ
10ʼ12ʼ
Lengths:11ʼ
Sunsky Clear Polycarbonate Panel(For MULTI-RIB)Available in Clear and White
R-Panel Fiberglass PanelItem #: 91235
13
ACCESSORIES
Not inventoried at all locations.
Images not drawn to scale.
U-Panel Fiberglass Panel37 3/8” X 12ʼItem #: 91212
Lengths:8ʼ
10ʼ12ʼ
Sunsky Clear Polycarbonate Panel(For R-PANEL)Available in Clear and White
Not inventoried at all locations.
MULTI-RIB / R-PANEL / MULTI-CORM-COR / U-PANEL / MULTI-V / MINI-RIB
Multi-Rib Fiberglass PanelAvailable in Clear, White and Opal11 ̓- 9120112 ̓- 9120716 ̓- 91218