Minimizing Micro-Cracks in Solar Cell Interconnections Paul Wood Advanced Product Applications...
-
Upload
jenna-baker -
Category
Documents
-
view
220 -
download
1
Transcript of Minimizing Micro-Cracks in Solar Cell Interconnections Paul Wood Advanced Product Applications...
Minimizing Micro-Cracks in Solar Cell Interconnections
Paul Wood
Advanced Product Applications Manager
Soldering Problems
Solder quality and panel-to- panel consistency
Micro-cracks on photovoltaic solar cells
Higher temperatures can crack the wafer substrate
Pressure can crack wafer substrate usually caused by heater in solder tool cooling
Buss bar tagging or repair is difficult if one panel needs to be replaced
Confidential and Proprietary to OK International. © OK International All rights reserved.
Solar factories still use soldering irons for touch up and rework
The flatness and pressure of soldering is still an issue for fully automated lines, so touch up and panel replacement is done by hand soldering.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Manual Panel Assembly
Two Soldering
Processes:
Stringing or Tabbing
Bussing
Confidential and Proprietary to OK International. © OK International All rights reserved.
Solar cell manual assembly soldering video
Confidential and Proprietary to OK International. © OK International All rights reserved.
Soldering iron must not overshoot temperature
Solder tip temperature must not overshoot
Is display temperature the actual correct tip temperature?
Having an unstable temperature causes operator variations in pressure. 1. Temperature self-regulation
2. No temperature overshoot3. Fast thermal response + recovery4. High watt density direct power
Confidential and Proprietary to OK International. © OK International All rights reserved.
How to measure repeatability
Confidential and Proprietary to OK International. © OK International All rights reserved.
Tip temperature display issue
Display temperature may not be tip temperatures
Up to 60°C difference between display and actual temperature is common at the tips. This is a common fault in conventional solder iron stations and is dangerous to substrate.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Micro-cracks are caused by high tip temperatures
Temperature stability and repeatability is critical, do not heat substrate connection temperature over 300°C
Confidential and Proprietary to OK International. © OK International All rights reserved.
How Micro-cracks occur
During the manual soldering operation, differential thermal expansion of the copper and the silicon elements can occur at temperatures greater than 300°C.
This differential can result in the formation of micro-cracks that may not be detected during the manufacturing process and result in a less than expected field lifespan.
The need for precise time and temperature control is additionally critical by the intermetallic layer requirement of 1-2µm that must be created during the solder joint formation.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Buss bar soldering
4-5mm ribbon is connected at the end of the panel to connect power ribbon. This is a heavier load than stringing operation, which is generally 2-3mm ribbons.
Confidential and Proprietary to OK International. © OK International All rights reserved.
Using hoof tips instead of chisel tips is a great improvement
Originally 2mm chisel tips were used by many companies, but they cooled down too fast.
OKi developed 2mm hoof tips for ribbon soldering, making it faster and safer.
OKi developed 4mm hoof tips for soldering busses faster, with no cooling at tips.
Chisel 2 mm
2mm hoof4mm hoof
Confidential and Proprietary to OK International. © OK International All rights reserved.
Smartheat PS-900 soldering system
OKi manufactures a thermal technology that will produce and maintain a specific self-regulated temperature, with a heater that requires no calibration
The heater technology is known as “Curie point heating”
Dynamically responds to PV tabbing and bussing thermal loads with measurably improved results
Confidential and Proprietary to OK International. © OK International All rights reserved.
Tip life and stability through the life of the tip is critical
Tips are tested for life and repeatability automatically
Plating thickness is optimized for performance
Too thick iron plate means poor performance, but long life
Hoof tips have been developed and proven as ideal for the solar industry
Confidential and Proprietary to OK International. © OK International All rights reserved.
Conclusion
OKi can provide economic solutions with high degree of repeatability
Proven hand soldering application with happy customers within China’s solar industry
Can supply standard equipment or work with OEM manufacturers to give custom solutions