MINI-SDL NT ENG 50Hz - Salmson · 0 36 25 Hm Mini SDL 1.5 kW SDL i Qm3/h 15 16 • Lifting of waste...
Transcript of MINI-SDL NT ENG 50Hz - Salmson · 0 36 25 Hm Mini SDL 1.5 kW SDL i Qm3/h 15 16 • Lifting of waste...
0
36
25
HmMini SDL1.5 kW
SDL i
Qm3/h 1615
• Lifting of waste water, foul water, water containing fibrous matter, fabrics, etc.
• Emptying of septic tanks, sewers• Lifting of water from institutional kitchens.• Discharge of non-corrosive food-proces-
sing wastes.
For homes, restaurants, garages, car parks, etc. or for any high-TDH (Total Dynamic Head).
OPERATING LIMITSFlow up to: 15 m3/hHead up to: 25 mMax. particle size: 10 mmDN discharge port: 40Protection index: 68
APPLICATIONS
AdVANTAGES- Combination of cast iron + 316L stain-
less steel for increased protection against corrosion and reliability.
- High-resistance, high-hardness cuting system.
- Spherical cuting system preventing fric-tion and premature wear.
- Fixed blade of ogival shape to channel the flow and ensure improved suction.
- Two types of standard installation: fixed installation in wet sump or mobile installation.
- Connections: Round counter-flange - dN 40, PN10 threaded R11/2
- Small pipe diameter and large discharge head for evacuation over long distances.
MACERATING SUBMERSIBLE PUMPSLifting of waste water
Commercial2 pole - 50 Hz
N° 145-8/ENG. - Ed.3/01-09
• MINI-SDL
MINI SDL
1
0
5
10
15
20
25
5040302010
160
20
40
60
80
1412108642
1614121086
100 15050
1 2 3 4
200 250
420
0
0,20,40,60,81
1,21,4
Qm3/h
Qm3/h
Hm Hft
P2 kW
Imp.gpm
Ql/minQl/s
Mini SDL
dESIGN• Hydraulic part:- Submersible, vertical axis.- Single shaft for pump and motor.- Intermediate oil-filled chamber between
pump and motor - insulated by a mechanical seal on the side of the pumped fluid, and a lip seal on the side of the motor.
- Single-channel impeller hosting mobile blade.
- Fixed blade fitted with an ogival mounted on the pump casing.
- Particle size: 6 mm
• Motor:- Sealed with dry rotor.- Integrated thermal overload protection. - WSK thermal sensor.- Direct start-up.- Speed: 2900 rpm- Winding: 1-phase; 230V 3-phase; 400V - Frequency: 50 HZ- Insulation class: 155 (F)- Protection index: IP 68- EC conformity
- ATEX for the 3-phase versions.
STANdARd CONSTRUCTIONMain parts MaterialHydraulics EN-GJL 250Motor casing 1.4404Impeller EN-GJL 250Shaft 1.0570Fluid-end seal Carb./Cer.Motor-end seal NBRBlades 1.4528
IdENTIFICATION
Mini S dL 2 04 2,0 T 4S: range
DL: shredding impeller
2 pole
Discharge-port DN in cm
P2 in kW
3-phase
400 V
CHARACTERISTICS
- Cast-iron pump + 316L stainless-steel motor + stainless-steel/cast-iron.
- 10 m removable cable.
- Single-channel impeller.
- Installation on mounting base with Ø33/42 guide bars or installation on stainless-steal support stand for mobile installation.
- ATEX as standard on the 3-phase version.
HYdRAULIC PERFORMANCES AT 2900 RPM
MINI SDL
2
SECTIONAL dRAWING 1111 - Pump casing 1221 - Motor casing 1600 A - Stuffing-box bushing 1600 B - Contact support 2281 - Closed single-channel impeller 2460 - Motor adjustment flange 2913 - Impeller attachment screw 3011A - Upper bearing 3011B - Lower bearing 4220 - Mechanical-seal: fixed part 4240 - Mechanical-seal: rotating part 4300 - Watertight lip seal 4610 A - O-ring joint (cap 9621) 4610B - O-ring joint (casing) 4610C - O-ring joint (sleeve 8361) 6545 - Support circlips 6700 - Key 8140 - Stator 8310 - Outside motor casing 8360 - 10-m power cable 8361 - Power-cable sleeve 8371 - Stuffing-box nut 8372 - Stuffing-box joint 8373 A - Cable tightening cone 8373 B - Anchor ring 9220 - Impeller shaft 9612 - Plug 9621 - Oil-chamber cap 9683 - Pump plate 9696 - Mobile blade 9697 - Permanent blade 9828 - Stator mount 9831A - Lower level 9831B - Upper level 9929 - Motor-casing Nylstop nut 9940 - Stuffing-box washer 9944 - Elastic washer
MINI SDL
3
A B C d E F G H H1 I J K LMini SDL 204/ 1,5M 130 110/125 18 110 73 160 491 467 462 71 98 202 105Mini SDL 204/ 1,5T4 130 110/125 18 110 73 160 491 467 462 71 98 202 105
Ø12
≥ 11
0
I 75
Ø26,9
E D
B A
M
DN2
H
G
Ø1000
14
C
80
80
40
88
310
(300
-330
)
J F
E
e
d
c
k
b
a
K
50
L
NG
O
K
T
H1
DN2
Fonctionnement dem/h P1 P2 I Vitesse Tension de réseau IP Câble Poids Granulométrie démarragemaxi kW kW A tr/mn m kg
Mini SDL 204/ 1,5M S1 50 2,1 1,5 9,5 2950 1~230V, 50Hz 68 10 30 6 DIRECTMini SDL 204/ 1,5T4 S1 50 1,7 1,5 3,2 2950 3~400V, 50Hz 68 10 30 6 DIRECT
M N O T dN2 a b c d e kmm mm mm mm mm mm mm mm mm mm mm
Mini SDL 204/ 1,5M 265 65 121 315 40 140 110 110 155 15 14Mini SDL 204/ 1,5T4 265 65 121 315 40 140 110 110 155 15 14
dIMENSION
TECHNICAL dATA
Operation Start-up/h P1 P2 I Speed Voltage Protection In dex
Cable Weight Particle size Start-upmaxi kW kW A rpm m kg
MINI SDL
4
Yn 5000
12
6
7
10
13
11
14
4
5
9
5410
7
137
145
105
228
265
88
110
150
180,
3
97
RECOMMENdEd ACCESSORIES FOR ATEX INSTALLATION
1 : Gate valve 2 : Ball check valve 4 : Electronic air-pressure switch (IPAE) 5 : IPAE cable bracket 6 : 3/4” DN guide bars 7 : Lifting chain 9 : Control box for ATEX installation (YN3000).
Install box outside explosive area. 10 : Base elbow set 11 : Motor electrical cable (10 m) 13 : Bleed hole to be drilled 14 : Zener barrier, essential for ATEX installation
Reminder: the 3-phase pumps are ATEX
1 - Gate valvesGate valve 4015489
2 - Check valveCheck valve 4015465
4, 5 & 14 - IPAEIPAE with 10 m de cable 2519921IPAE with 30m de cable 2519922IPAE with 50m de cable 2519923IPAE cable bracket 2519927Zener barrier 2521216
7 - Lifting chainLifting chain 4031693
9 - Control box Mini SdL 204/ 1,5M1 pump YN 3112 M 25229692 pumps YN 3212 M 2522871Mini SdL 204/ 1,5T41 pump YN 3112 T4 25229702 pumps YN 3212 T4 2522872
10 - Base elbow set SDL Base elbow set 2057179
MINI SDL
5
11
3
5
Yn 5000
12
6
7
10
13
11
8
54
107
137
145
105
228
265
88
110
150
180,
3
97
RECOMMENdEd ACCESSORIES FOR PERMANENT INSTALLATION
1 : Gate valve 2 : Ball check valve 3 : Float switch 5 : Wall-mounted cable bracket 6 : 3/4” guide bars 7 : Lifting chain 8 : YN3000 control box 10 : Base elbow set 11 : Motor electrical cable (10 m) 13 : Bleed hole to be drilled
1 - Gate valvesGate valve 4015489
2 - Check valve Check valve 4015465
3 - Float switchNivo 430X1-10M ECOLO 4027319Nivo 430X1-20M ECOLO 4027320Wall-mounted cable bracket 4013188
7 - Lifting chainLifting chain 4031693
8 - Control box Mini SdL 204/ 1,5M1 pump YN4112 40914322 pumps YN4212 4091434Mini SdL 204/ 1,5T41 pump YN4105 40914312 pumps YN4205 4091433
10 - Base elbow set SDL base elbow set 2057179
MINI SDL
6
3
2
1
270
78
315
180
G 1¼
G 1
¼
7676
RECOMMENdEd ACCESSORIES FOR MOBILE INSTALLATION
1 : Mobile-installation support stand 2 : Straight elbow3 : Lifting chain
1 - SupportMobile-installation support stand 2057239
2 - 40-dN elbow coupling with threadElbow discharge 2057400
3 - Lifting chainLifting chain 4031693
MINI SDL
7
FEATURESa ) Electrical - 3 phase 400 V – 50-Hz direct start-up.
- Compulsory overload protection (discon-necting switch, circuit breaker or control box with level regulator).
b) Installation- Pump in vertical position with permanent
and mobile installation.- Mobile installation: discharge port connec-
ted by elbow coupling to flexible pipe with diameter greater than pump-discharge diameter.
- Dual installation: pumps can be coupled using a manifold.
- Gate and check valves: installation recom-mended in upper section of discharge pipe.
- Flexible or rigid connector pipes.
c) Packaging- Pump delivered in recyclable cardboard
packaging.- Pump delivered with 10-m H07RN – F power
cables.- Accessories packaged separately.
RECOMMENdEd ACCESSORIES• Yn 3100 - Yn 3200
ApplicationThese control boxes handle one (YN3112) or two (YN3212) pumps with a maximum power requirement of 4 kW.
Technical characteristics- Operating voltageYN3112 T4, YN 3212 T4 : 3 ~ 400 V
(L1,L2,L3,PE)YN3112 M, YN 3212 M : 1 ~ 230 V (L,N,PE)- Frequency : 50/60 Hz- Maximum connected load : P2 ≥ 4 Kw- Intensity range : 0,3 -12,0A (M or T4)- Type of protection : IP 65- Temperature range : -20 à +60°C- Alarm contact :Contact load 250 V, 1 A
All the signalling and control elements are found on the front panel of the switch box.These consist of buttons and a red knob on the front panel.
• IPAE
Electronic air-pressure switch for clean and waste water.- Adapted for use in explosive environments.- Operates for both emptying and filling.- Complies with ATEX Directive
94/9/CE: explosive-environment protection.
- Remote control.- Flame-proof.
• NIVO430
- Ecological, mercury-free float switch for waste water.
- Operates for both emptying and filling, with overload switch.
Any alteration to the settings (using a digital potentiometer) is immediately displayed on the LCD screen in plain English.The filling level of the station is shown in cm (with IPAE 0-1mCE).The electronic control device is placed in a wall box (IP65).
Advantages :- innovating: levels adjusted by IPAE- Easy to install: the adjustments are made
outside the tank.- Easy to maintain with meters which count
the number of pump start-ups and hours of operation.
- Evolutive: feeds back signals
Safety : - If not used for a while, the box gives the
pumps an automatic burst to release the mechanical seal.
- Automatic reset.- Two pumps can be run in parallel in the event
of heavy discharge (YN3200)
- Unaffected by water temperature and pre-sence of foam.
- Acid-resistant.- Total reliability, high precision (2 cm),
economical.- Input voltage: 220 V - 50 Hz.- Used with YN5000E.
For ATEX installation, use the Zener barrier (for more information, see IPAE Instructions for Use).
MINI SDL
8