Mi Power Bank ProUser Manual

Safety: Mi Power Bank Pro has multiple safeguard technologies to provide over-charge, over-discharge, high temperature, and short circuit protection in all working conditions.

Efficiency: Supports fast charging and discharging at 5.0V 2.4A 9.0V 2.0A

12V 1.5A output.

Compatibility: The product has a built-in USB charging controller, compatible with most smartphones, tablets, and devices. It supports mainstream fast charging devices, and can boost to 9V/12V.

Quality: ATL Li-polymer batteries and TI chips.

Notes:

The Power check button is not a Power button. Mi Power Bank Pro detects charging and discharging automatically. The Power indicator turns off two minutes after discharging is completed.

Please read the user manual before using the product

Product Introduction

Product Features

Thank you for choosing Mi Power Bank Pro. The product is a high-capacity portable charger that uses ATL Li-polymer batteries and TI chips for a safe, efficient, and compatible user experience.

USB (Output)

Type C (Input) Power Indicator

Power Check

Model: PLM03ZM

Battery type: Li-polymer

Cell capacity: 10000mAh 3.85V (38.5Wh)

Operating temperature: 0°C~45°C

Dimensions: 128.5×75×12.6mm

Input: 5.0V 2.0A 9.0V 2.0A 12V 1.5A

Output: 5.0V 2.4A 9.0V 2.0A 12V 1.5A

Charging time: approx. 3.5 hours (9V/2A or 12V/1.5A adapter, standard cable),

approx. 5.5 hours (5V/2A adapter, standard cable)

Connect with Mi AC Adapter to charge Mi Power Bank Pro. The indicator shows charging conditions as follows:

Connect with Mi Power Bank Pro to charge your device.

The indicator shows discharging conditions as follows:

Specifications

Charging

Discharging

* Small current discharge: when Mi Power Bank Pro is not charging, double press the Power check button to enter Small current discharge mode to charge small devices, such as Bluetooth headphones and smart bands. The indicator LEDs will turn on one by one in succession, indicating that Mi Power Bank Pro has entered Small current discharge mode. To exit Small current discharge mode, press the Power check button once.

LED1LED3 LED2

LED4

Power Level

Fully ChargedCharging Error Blinking

BlinkingOnOnOnOn

Blinking

BlinkingOnOnOn

Off

Blinking

BlinkingOnOn

OffOff

Blinking

BlinkingOn

OffOffOff

Power Level

UndervoltageBlinking

Off

Blinking

Blinking

Blinking

OffOff

Blinking

Blinking

Blinking

OffOff

Off

Blinking

Blinking

OffOff

Off

Blinking

Off

Warnings

NotesPlease make sure to fully charge Mi Power Bank Pro on its first use.

When charging a device with Mi Power Bank Pro, please check whether your device displays the battery charging icon to confirm that Mi Power Bank Pro is working properly.

When charging Mi Power Bank Pro or charging a device with Mi

Power Bank Pro, please be sure to use the right charging cable.

When all indicator LEDs lights go out, Mi Power Bank Pro is in low in power mode. Please recharge as soon as possible.

When charging a device with Mi Power Bank Pro, the device will use Mi Power Bank Pro's battery first.

Once your device is fully charged, please disconnect it from Mi Power Bank Pro to avoid further discharge.

When the product enters protection mode (LEDs don't light up after pressing the Power check button) due to output short circuit or other reasons, please charge Mi Power Bank Pro with an external charger to resume.

Mi Power Bank Pro contains Li-ion batteries. Do not open the casing to avoid battery damage or other dangers.

Please do not dismantle, press, puncture and short circuit Mi Power Bank Pro, or expose the product to liquids, fire, or environments where temperature is higher than 60°C (140°F).

FCC StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

CEHereby declares that this equipment is in compliance with the Electromagnetic Compatibility (EMC) Directive 2014/30/EU.

Test standards:

EN61000-6-3: 2007+A1: 2011 EN61000-3-2: 2014

EN61000-3-3: 2013 EN61000-6-1: 2007

EN55032: 2015 EN55024: 2010+A1: 2015

To promote environmental protection, Xiaomi avoids excessive packaging.

Anti-counterfeit labels are placed on the outer packaging of every certified 10000mAh Mi Power Bank Pro. Please scratch the coating to see the verification code, and check if the product is genuine on this website: http://www.mi.com/verify

Anti-counterfeit label

Scratched off label

About anti-counterfeit labels

Principal: Xiaomi Communications Co., Ltd.

Manufacturer: Zimi Corporation (a Mi Ecosystem company)

Address: 159 Chengjiang Road Unit A913, Jiangyin City, Jiangsu, China