MFL30138908_svc
-
Upload
arturo-nava -
Category
Documents
-
view
215 -
download
0
Transcript of MFL30138908_svc
-
7/28/2019 MFL30138908_svc
1/45
100
WASHING MACHINESERVICE MANUAL
READ THIS MANUAL CAREFULLY TO DIAGNOSEPROBLEMS CORRECTLY BEFORE SERVICING THE UNIT.
MODELS: WD-12EFD / WD-12TFD / WD-12EFP
CAUTION
Website: http: //www.LGEservice.comE-mail: http: //www.LGEservice.com/techsup.html
!
-
7/28/2019 MFL30138908_svc
2/45
101
NOV. 2006 PRINTED IN KOREA P/No.: MFL30138908
-
7/28/2019 MFL30138908_svc
3/45
2
CONTENTS
1. SPECIFICATIONS .........................................................................................................................3
2. FEATURES & TECHNICAL EXPLANATION ................................................................................ 4
3. PARTS IDENTIFICATION ............................................................................................................ 7
4. INSTALLATION & TEST ............................................................................................................... 8
5. OPERATION ................................................................................................................................11
6. WIRING DIAGRAM/PROGRAM CHART.....................................................................................14
7. TROUBLESHOOTING.................................................................................................................15
7-1. BEFORE PERFORMING SERVICE ...................................................................................15
7-2. QC TEST MODE.................................................................................................................15
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY ......................................................15
7-4. ERROR DISPLAY ...............................................................................................................16
8. ERROR DIAGNOSIS AND CHECK LIST ....................................................................................18
8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION ........................................18
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING ..............................................................21
9. DISASSEMBLY INSTRUCTIONS ...............................................................................................30
10. EXPLODED VIEW .....................................................................................................................41
10-1. CABINET & CONTROL PANEL ASSEMBLY....................................................................41
10-2. DRUM & TUB ASSEMBLY................................................................................................42
10-3. DISPENSER ASSEMBLY .................................................................................................43
10-3. DISPENSER ASSEMBLY .................................................................................................43
10-4. THE EXPLODED VIEW OF DRYER.................................................................................44
-
7/28/2019 MFL30138908_svc
4/45
3
1. SPECIFICATIONS
ITEM WD-12EFD / WD-12TFD / WD-12EFP
COLOR BLUE WHITE
POWER SUPPLY 110V a.c 60 Hz
PRODUCT WEIGHT 80 kg
WASHING 280 W
FAN MOTOR 25 W
DRAIN MOTOR 32 W
WASH HEATER 1000 W
DRY HEATER 1200 W
WASH 42 rpm
SPIN 1200 rpm
CYCLES 9
TEMPERATURES 5
SPIN SPEEDS 5
OPTIONS Soak, Pre Wash, Rinse+Spin, Spin Only, Dry Only
CUSTOM PROGRAM Incorporated
WATER CIRCULATION OK
OPERATIONAL WATER PRESSURE 4.5-145 psi (30-1000 kPa)
CONTROL TYPE Electronic
WASH CAPACITY 12 kg
DRY CAPACITY 7 kg
DIMENSIONS 635x740x925(mm)
DELAY WASH From 3 hours to 19 hours
DOOR SWITCH TYPE AUTO type
WATER LEVEL 10 steps (by sensor)
LAUNDRY LOAD SENSING Incorporated
ERROR DIAGNOSIS Incorporated
AUTO POWER OFF Incorporated
CHILD LOCK Incorporated
ELECTRIC POWER
CONSUMTION
REVOLUTION SPEED
-
7/28/2019 MFL30138908_svc
5/45
4
2. FEATURES & TECHNICAL EXPLANATION
2-1. FEATURES
Direct Drive SystemThe advanced Brushless DC motor directly drives the drumwithout belt and pulley.
Tilted Drum and Extra Large Door Opening
The tilted drum and extra large door opening make it possibleto load and unload easily.
Water CirculationSpray detergent solution and water onto the load repeatedly.Clothes are soaked more quickly and thoroughly during the wash cycle.Detergent suds are eliminated more easily by the water showerduring rinse cycle. The water circulation system uses bothwater and detergent more efficiently.
RollerJets
The washing ball enhances wash performance and reduces
damage to clothing. The jets spray and help tumble clothes to enhancewashing performance while maintaining fabric care.
Automatic Wash Load Detection
Automatically detects the load and optimizes the washing time.
Built-in Heater
The internal heater automatically heats the water to the optimumtemperature on selected cycles.
Child Lock
The Child lock feature prevents children from pressing any buttonsto change the settings during operation.
, ,
-
7/28/2019 MFL30138908_svc
6/45
5
2-2. NEURO FUZZY WASHING TIME OPTIMIZATION
To get the best washing performance, optimal time is determined by the water temperature,
the selected washing temperature, and the size of the load.
2-3. WATER LEVEL CONTROL
This model incorporates a pressure sensor which can sense the water level in the tub.
The water supply is stopped when the water level reaches the preset level, the washing
program then proceeds.
Spinning does not proceed until the water in the tub drains to a certain level.
2-4. DOOR CONTROL The door can be opened by pulling the door handle whenever washer is not in operation.
When the cycle is completed, the DOOR LOCKED light will turn off.
If a power failure has occurred while in operation, the door will unlock after 5 minutes.
Clicking sounds can be heard when the door is locked/unlocked.
NEURO-FUZZY
load
size
selectedwashing
temperature
watertemperature
washing time
rinsing time
spin rhythm, time
the bestwashingperformance
SENSING PROCESSING DETERMINATION EFFECT
-
7/28/2019 MFL30138908_svc
7/45
6
2-5. THE DOOR CAN NOT BE OPENED While program is operating
When a power failed and power plug is taken out in operation
While Door Lock lights turn on.
White the motor is in the process of intertial rotating, through the operation is paused.
2-6. DOOR LOCKED LAMP LIGHTS When the frequency of water level is lower than 22.9 kHz
(It can be canceled when the frequency is more than 23.8 kHz)
When the temperature inside the tub is higher than 45 C and water level is not 25.5 kHz
(It can be canceled when the water level is 25.5 kHz or the temperature inside the tub is lower than 40 C)
2-7. CHILD LOCK Use this option to prevent unwanted use of the washer. Press and hold PRE WASH button for 3 seconds to
lock/unlock control.
When Child lock is set, CHILD LOCK lights and all buttons are disabled except the Power button. You can
lock the washer while it is operating.
2-8. WATER CIRCULATION When Washing and Rinsing function of shower at the upper part of Gasket.
When Washing, it continuously operates for 3 minutes and intermittently.
When Rinsing, it continuously operates after completion of water supply.
-
7/28/2019 MFL30138908_svc
8/45
7
3. PARTS IDENTIFICATION
ACCESSORIES
Water Circulation Nozzle
Cotton
Eco
Woo/Silk
HandWash
Duvet
Drain
Synthetic
Delicate
Quick 30
-
7/28/2019 MFL30138908_svc
9/45
8
1 Before servicing, ask the customer what the trouble is.
2 Check the setup (power supply is 110V ac 60Hz, remove the transit bolts....).
3 Check with the troubleshooting guide.4 Plan your service method by referring to the disassembly instructions.
5 Service the unit.
6 After servicing, operate the appliance to see whether it functions correctly.
STANDARD INSTALLATIONThe appliance should be installed as follows:
REMOVE THE SHIPPING INSTALL THE APPLIANCE ADJUST THE
BOLTS ON A FLAT AND FIRM SURFACE LEVELING
Remove the 4 shipping bolts Turn the leveling feet to adjustwith the supplied wrench. the appliance.
Do first lower side to remove easily.
Keep the shipping bolts and
spanner for future use. Insert the 4 caps
(provided) into the hole.
Turn clockwise to raise;
counterclockwise to lower.
4. INSTALLATION & TEST
Cotton
Cotton-Eco
Woo/Silk
HandWash
Duvet
Drain
Synthetic
Delicate
Quick30
-
7/28/2019 MFL30138908_svc
10/45
-
7/28/2019 MFL30138908_svc
11/45
10
MAX
Cotton
Cotton-Eco
Woo/SilkHandWash
Duvet
Drain
Synthetic
Delicate
Quick30
Cotton
Cotton-Eco
Woo/Silk
HandWash
Duvet
Drain
Synthetic
Delicate
Quick30
Cotton
Cotton-Eco
Woo/SilkHandWash
Duvet
Drain
Synthetic
Delicate
Quick30
TEST OPERATION
Connect the power plug to
the outlet.Connect the inlet hoses.
Power off and the power on.Press the SPIN SPEED button.Press the START/PAUSE button.
Check the spin and drainfunctions. Listen for a click to determine
if the door is unlocking.
Listen for a click to determine if
the door has locked.
If SVC is needed during check,remove the remaining water bypulling out the hose cap.
Preparation for Press the POWER button. Press the Start/Pausewashing. button.
Press the WASH/RINSE button Check if the drum rotates Check if water is suppliedand the present temperature will clockwise and counterclockwise. through the detergent dispenser.be displayed.
Check the water heating Check the automatic Check the water supply.function. reverse rotation.
Check the drain and spin Press the Water removalfunctions. START/PAUSE button.
-
7/28/2019 MFL30138908_svc
12/45
11
5. OPERATION
WD-12EFD / WD-12TFD / WD-12EFP
-
7/28/2019 MFL30138908_svc
13/45
12
Use this button to turn the powerOn/Off.
Rotate the Cycle selectorknob to select the cycledesigned for different
types of fabric and soillevels.
Prewash: Use this option for loads that need pretreatment. Itadds 16 minutes prewash and drain.
Rinse+Spin: Use this option to rinse and then spin.
Extra Rinse: This option provides an additional rinse cycle.
Soak: Use this mode to wash normal clothes or think and heavyclothes which are excessively dirty.
Spin Only: When you want Spin only, select this option.
Dry only: When you want Dry only, select this option.
Use this button to Start/Stop the washer.
This display shows:
a) the estimated time remaining in thecycle when operating.
b) an error code when an error has beendetected.
-
7/28/2019 MFL30138908_svc
14/45
13
TIME SAVE
DRY Button Rinse, Spin, Temp. Button
TIME DELAY
Use this option to prevent unwanted use of the washer.
Press and hold PRE WASH button for 3 seconds to
lock/unlock control.
When Child lock is set, CHILD LOCK lights and all
buttons are disabled except the Power button.
You can lock the washer while it is operating.
This option can be used toreduce the time of a wash
program
To use this option pressthe Time Save buttononce before wash
program is start.
Dry programs selected by pressing theDry button.
By pressing the button [Time-Very-Cupboard-Iron-Low Temp.] can beselected.
Allows the start of any
cycle to be delayed for3~19 hours.
Select a water temperature based on the type of
load you are washing. To change the spin speed, press the Spin Speed
button repeatedly to cycle through availableoptions.
To change the soil level, press the Soil Levelbutton repeatedly until the desired setting is on.
Press repetedly to adjust the volume of theBeeper.
These lights show which portionof the cycle the washer isoperating.
-
7/28/2019 MFL30138908_svc
15/45
14
6. WIRING DIAGRAM/PROGRAM CHART
CYCLEWash Rinse
Spin
(min.)(min.)(min.)
**Approx
Working
Time
(Minutes)
About
About
About
About
About
About
About
About
About
About
About
About
About
About
Extra & Stain(4~5)
Wash
Pre
W
S
W
S
W
S
W
S
W
S
W
S
I
S
I
S
I
S
I
S
D
T
I
S
Wash
Rinse
Rinse
Rinse
Rinse
Wa
sh
Heat
Drain
Drain
Drain
Drain
Spin
Dry
Drain
Drain
Main
C
OU
R
S
E
Cotton
Synthetic
Wool/Silk
Delicate
Duvet
Cotton-Eco
Hand Wash
Wash
Rinse
Spin
Quick 30
Wash+Rinse
Wash+Spin
Rinse+Spin
TIME(SEC.)
* Wash time is in minutes.
** The total working time will vary with the load size,
water temperature and ambient temperature.
-
7/28/2019 MFL30138908_svc
16/45
15
7. TROUBLESHOOTING
7-1. BEFORE PERFORMING SERVICE Be careful of electric shock when disconnecting parts while troubleshooting.
The voltage of each terminal is 110V a.c and DC when the unit is plugged in.
7-2. QC TEST MODE.The washer must be empty and the controls must be in the off state.
1. Press the SPIN SPEED and SOIL LEVEL buttons simultaneously.
2. Press the Power button, while the above condition. Then buzzer will sound twice.
3. Press the Start/Pause button repeatedly to cycle through the test modes.
7-3. HOW TO CHECK THE WATER LEVEL FREQUENCY Press the Spin and Dry button simultaneously.
So, for example a display indicating 241: a Water level frequency of 241 x.1 kHz
= 24.1 kHz
The digits indicate the water level frequency ( x.1 kHz ).
Check Point Display Status
None Turns on all lamps and locks the door.
1 time Tumble clockwise. rpm (40~50)
2 times Low speed Spin. rpm
3 times High speed Spin. rpm
4 times Inlet valve for prewash turns on. Water level frequency (25~65)
5 times Inlet valve for main wash turns on. Water level frequency (25~65)
6 times Inlet valve for hot water turns on. Water level frequency (25~65)
7 times Inlet valve for bleach turns on. Water level frequency (25~65)
8 times Tumble counterclockwise. rpm (40~50)
9 times Heater turns on for 3 sec. Water temperature
10 times Circulation pump turns on. Water level frequency (25~65)
11 times Drain pump turns on. Water level frequency (25~65)
12 times Power off and unlock the door. Turn off all lamps.
Number of times theStart/Pause button is pressed
-
7/28/2019 MFL30138908_svc
17/45
16
7-4. ERROR DISPLAY
If you press the START/PAUSE button when an error is displayed, any error exceptd ewill
disappear and the machine will go into the pause status.
In case ofd e,d e,d eif the error is not resolved within 20 sec., or the in case of other errors,
if the error is not resolved within 4 min., power will be turned off automatically and the error code will
blink. But in the case ofd e, power will not be turned off.
ERROR SYMPTOM CAUSE
WATER INLET
ERROR
Correct water level (246) is not reached within 8 minutesafter water is supplied or it does not reach the preset water
level within 25 minutes.
The load is too small. The appliance is tilted.
Laundry is gathered to one side. Non distributable things are put into the drum.
1
2IMBALANCE
ERROR
Not fully drained within 10 minutes.3DRAIN
ERROR
Water is overflowing (water level frequency is over 213).
If is displayed, the drain pump will operate todrain the water automatically.
4OVER FLOW
ERROR
The SENSOR SWITCH ASSEMBLY is out of order.5
PRESSURE
SENSOR
ERROR
Door not all the way closed.
Loose electrical connections at Door switch andPWB Assembly.
The DOOR SWITCH ASSEMBLY is out of order.
6 DOOR OPEN
ERROR
The THERMISTOR is out order.7HEATING
ERROR
-
7/28/2019 MFL30138908_svc
18/45
17
ERROR SYMPTOM CAUSE
OVER
CURRENT
ERROR
MAIN PWB ASSEMBLY is out of order.
Winding in the STATOR ASSEMBLY is short-circuited.
The connector (3-pin, male, white) in the MOTOR
HARNESS is not connected to the connector(3-pin, female, white) of STATOR ASSEMBLY.
The electric contact between the connectors
(3-pin, male, white) in the MOTOR HARNESSand 4-pin, female, white connector in the MAIN PWBASSEMBLY is bad or unstable.
The MOTOR HARNESS between the STATORASSEMBLY and MAIN PWB ASSEMBLY is cut (opencircuited).
The hall sensor is out of order/defective.
8
9 LOCKEDMOTOR
ERROR
Loose Ball Sensor Connector. Ball Sensor is out of order.
Displayed only when the START/PAUSE button is firstpressed in the QC Test Mode.
10BALL SENSOR
ERROR
The washer experienced a power failure.12POWER
FAILURE
EEPROM is out of order.
Displayed only when the START/PAUSE button is firstpressed in the QC Test Mode.
11EEPROM
ERROR
-
7/28/2019 MFL30138908_svc
19/45
18
8-1. DIAGNOSIS AND SOLUTION FOR ABNORMAL OPERATION
8. ERROR DIAGNOSIS AND CHECK LIST
SYMPTOM GUIDE FOR SERVICE CALL
No power
Water inlet trouble
Y E S
Y E S
Y E S
N O
N O
Y E S
N O
N O
Is the power plug connected firmly to
110V a.c outlet?
Power failure? or Breaker opened?
Is the outlet controlled by a switch?
Visit to service.
Is displayed?
Is the tap opened?
Is the tap frozen?
Is the water supply shut-off?
Is filter in the inlet valve clogged with
foreign material?
Visit to service.
Clean the filter of
inlet valve
-
7/28/2019 MFL30138908_svc
20/45
19
SYMPTOM GUIDE FOR SERVICE CALL
Door error
Drain trouble
Was the load too large?
Visit to service.
Visit to service.
-
7/28/2019 MFL30138908_svc
21/45
20
SYMPTOM GUIDE FOR SERVICE CALL
Suds overflow from the
appliance.
(In this condition, wash and
spin do not operate normally); - 5
; - 5
; - 5
; - 5
M
A
X
Is a low-sudsing detergent used?
Is the proper amount of detergent used
as recommended?
Recommend to reduce the amount
of detergent.
Is liquid laundry product put in the correct
compartment of the dispenser?
Is the cap clogged?
Explain proper use of liquid laundry products.
Clean the compartment.
Visit to service.
LOW-SUDSING
This appliance has an automatic suds sensing function whichprevents overflow.
When excessive suds are sensed, the suds removingimplementations such as drain, water input, pause will operate,without rotating the drum.
Liquid laundry products do not
flow in.
-
7/28/2019 MFL30138908_svc
22/45
21
N O
Y E S
Y E S
Y E S
Y E S
N O
N O
N O
N O
Y E S
C o n n e c t o r
Is the supplied voltage 120 V AC?
Is the voltage between the 2 FILTER ASSEMBLYconnectors 110V a.c 60Hz?
Is the LED (1) on?
Are the connectors (2) on the PWB loose?
Is wire of the DISPLAY PWB ASSEMBLY
broken?
Replace DISPLAY PWB ASSEMBLYor repair wire.
Check the fuse or resetthe circuit breaker.
Replace the FILTERASSEMBLY (CIRC).
Replace MAIN PWB
ASSEMBLY.
Reconnect.
Replace the MAIN PWB
ASSEMBLY.
NO POWER
8-2. FAULT DIAGNOSIS AND TROUBLESHOOTING
1. Be careful of electric shock if disconnecting parts while troubleshooting.
2. First of all, check the connection of each electrical terminal with the wiring diagram.
3. If you replace the MAIN PWB ASSEMBLY, reinsert the connectors correctly.
CAUTION
-
7/28/2019 MFL30138908_svc
23/45
22
Y E S
Y E S
Y E S
N O
N O
H i g h e r
U n b a l a n c e P a r t
L o w e r
A d j u s t a b l e f e e t
L o c k
N u t
A d j u s t a b l e f e e t
B a s e P a c k i n g
L e v e l
Have all the transit bolts and base packingbeen removed?
Remove the transit boltsand Base packing.
Move the washer orreinforce the floor.
Is the washer installed on a solidly constructedfloor?
Check if the washer is perfectly level as follows:
Check the leveling of the washer with a Level
and check that the washer is stable.
Put an unbalance part (rubber) inside of drum
and start QC test mode and run in high spin(Refer to section 7-2).When the machine is spinning in high speed,verify that it is stable.
VIBRATION & NOISE IN SPIN
If it is not stable, adjust feet accordingly. Afterthe washer is level, tighten the lock nuts up
against of the base of the washer. All lock nutsmust be tightened.
If you do not have the unbalance part, put 4.5 to
6.5 lbs (2 to 3 kg) of clothing. Once loaded,press power, Rinse+Spin and the start/pausebutton in sequence.When the machine is spinning in high speed,
verify that it is stable.
-
7/28/2019 MFL30138908_svc
24/45
23
If it still has severe vibration and noise, regulate a specific spin speed that generates excessive vibration and
noise as follows:
1) Put an unbalance part (rubber) inside of the drum.
2) Start the QC test mode (Refer to section 7-2).
3) Press Delay Wash button, then is displayed.
4) Press the Spin Speed button repeatedly to select Extra High.
5) Press the Quick Cycle button, the spin speed is displayed.
6) Press the Start/Pause button.
7) Press the Beeper button repeatedly to set spin speed (600, 900, 1020, 1120 rpm) and check if there is vibrationand noise.
8) If there is no vibration and noise, increase the spin speed by pressing Beeper button.
9) If there is vibration and noise, rotate the Cycle selector knob clockwise to reduce the Spin Speed (reduce by 50and 100 rpm). In case of 600 rpm, it can not reduce the spin speed.
10) If vibration and noise are reduced, press the Quick Cycle button to store (2 beep sounds).
* If you want to return to factory default spin speed setting, repeat above steps except step 9).
-
7/28/2019 MFL30138908_svc
25/45
24
NO
YES
NO
NO
YES
NO
YES
YES
NO
NO
YES
YES
YES
NO
NO
NO
YES
1
Dry
Dry
MAX
Is water supply shut-off?
Is the tap opened?
When you press both Spin button and Dry buttonsimultaneously, is the water level frequency below246?
Is the inlet valve filter clogged?
Is resistance between each terminal of INLETVALVE ASSEMBLY 0.8-1.2 k?
Verify the voltage of the inlet valve connector is
110V a.c 60Hz.
(Refer to 7-2 QC TEST MODE)
Is water supplied?
Are receptacles correctly connected to the
terminals of the INLET VALVE ASSEMBLY?
Has detergent been put in the correct compartmentof the dispenser?
Is the detergent caked or hardened?
Open the tap.
Check the AIR CHAMBER
and the tube (clogged).
Clean the filter.
Replace the INLET VALVE
ASSEMBLY.
Check electrical connection.
Replace the MAIN PWB
ASSEMBLY.
Refer to
^NO WATER SUPPLY_
Check the wiring.
Put the detergent in thecorrect place.
Clean the dispenser.
NO WATER SUPPLY
DETERGENT DOES NOT FLOW IN
-
7/28/2019 MFL30138908_svc
26/45
25
P r e w a s h
B l e a c h
M a i n w a s h
M
A
X
M
A
X
M
A
X
ABNORMAL SOUND
LIQUID DETERGENT/SOFTENER/BLEACH DOES NOT FLOW IN
Secure the bolt.
Replace the STATORASSEMBLY or ROTOR
ASSEMBLY.
Refer to
^NO WATER SUPPLY_
Check the wiring on the
dispenser.
Put it in the correct
compartment.
Clean the Cap andContainer.
Is the motor bolt loosened?
Is there friction noise coming from the motor?
Is water supplied?
Are the plugs correctly connected to the terminals of
the INLET VALVE ASSEMBLY?
Is liquid detergent/softener/bleach put in the correct
compartment of the drawer?
Is the liquid detergent/softener/bleach cap clogged?
-
7/28/2019 MFL30138908_svc
27/45
26
N O
Y E S
Y E S
Y E S
Y E S
N O
N O
N O
N O
Y E S
Y E S
N O
1 1 0 V a . c
1 1 0 V a . c
Replace the
SENSOR SWITCH
ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY.
Repair the DRAIN HOSEASSEMBLY.
Remove foreign material.
Reconnect or repair theconnector
Replace the DRAINPUMP ASSEMBLY.
Replace the MAIN PWB
ASSEMBLY.
When pressing Spin and Dry at the same time after
draining, is the water level frequency 255?
When pressing Spin and Dry buttons at the same time
while washing, is the water level frequency between
230 - 243 ?
Check the voltage between two pins while pressing
the POWER button. Is the voltage 110V a.c?
Is the drain hose twisted or frozen?
Is the impeller of the drain pump clogged?
Is the connector disconnected, disassembled?
Is the coil of the drain pump too high or low?
(resistance of the coil is 10-20)
When checking voltage between connectors during
spin, is the voltage 110V a.c as in the figure?
HEATING WITHOUT WATER
DRAIN MALFUNCTION
-
7/28/2019 MFL30138908_svc
28/45
27
(1)
Temp.
110V a.c
Push the THERMISTORtightly to the rubber.
When checking the THERMISTOR on the tub,
is the THERMISTOR loose?
HEATING CONTINUOUSLY ABOVE
THE SETTING WATER TEMPERATURE
WASH HEATER TROUBLE
-
7/28/2019 MFL30138908_svc
29/45
28
Y E S
Y E S
Y E S
Y E SY E S
N O
N O
N O
N O
N O
H o s e
C o n n e c t o r
( W h i t e )
C o n n e c t o r
C o n n e c t o r
H o s e
WILL NOT CIRCULATE WATER
Is the impeller of the drain pump clogged?
Are the Hose Connector and/or Hose clogged?
Is the connector disconnected, disassembled?
Is the coil of the right side of drain pump openor short circuited? (Coil R is 18-30 )
When checking voltage between theconnectors during spin, is the voltage 110V a.c,as the figure?
Remove foreign material.
Remove foreign material.
Reconnect or repairthe connector.
Replace PUMP MOTOR
ASSEMBLY.
Replace the MAIN PWBASSEMBLY.
-
7/28/2019 MFL30138908_svc
30/45
29
(1)
(1) (2)
SPIN TROUBLE
Check the SENSOR SWITCHASSEMBLY or HOSE (Pressure).If the problem is on the SENSORSWITCH ASSEMBLY or theHOSE, replace the SENSORSWITCH ASSEMBLY or theHOSE.
Normal
Correct the connection.
Replace the STATORASSEMBLY
Check during spin if the frequency of the waterlevel is 248 or more.
Press the START/PAUSE button 2 times in QCTest mode, is the drum spinning at low speed?
Is it disconnected, or disassembled?[Red: 3pin (1), NA: 4pin (2)]
Check the motor connector, Is the resistance ofthe terminal the same as the figure?
MOTOR TERMINAL
Resistance of terminal:
-/-/-: About 5 -15
Replace the MAIN PWB ASSEMBLY
Does the spring of Latch Hook actuate?
Is there clicking sound once or twice when theSTART/PAUSE button is pressed to start the cycle?
Is DOOR SWITCH ASSEMBLY broken?
Replace Door Assembly.
Check the DOOR SWITCH
ASSEMBLY Connector andMAIN PWB ASSEMBLY(Red 3 pin, Yellow 4 pin and
white 3 pin connector (1)).
Replace the DOORSWITCH ASSEMBLY.
-
7/28/2019 MFL30138908_svc
31/45
30
9. DISASSEMBLY INSTRUCTIONS
DISPLAY PWB ASSEMBLY
TOP PLATE ASSEMBLY
CONTROL PANEL ASSEMBLY
DRAWER
CONTROL PANEL ASSEMBLY
Be sure to unplug the machine out of the outlet before disassembling and repairing the parts.
Unscrew 2 screws on the back of the top plate.
Pull the top plate backward and upward as shown.
Disconnect the Display PWB Assembly connector
from Trans cable.
Pull out the drawer and unscrew 2 screws.
Lift the left side of the Control Panel Assembly and
pull it out.
Unscrew the 9 screws from the Control Panel
Assembly. Disassemble the Display PWB Assembly.
-
7/28/2019 MFL30138908_svc
32/45
31
Disconnect the POWER connector and SENSOR
SWITCH ASSEMBLY.
Remove the Protect Cover.
Disconnect the connectors.
Unscrew 1 screw on the back.
Disassemble the Main PWB.
CONNECTOR
PROTECT COVER
MAIN PWB ASSEMBLY
-
7/28/2019 MFL30138908_svc
33/45
32
Disassemble the top plate assembly.
Pull out the drawer.
Push out the DISPENSER ASSEMBLY afterunscrew 2 screws.
Unscrew the nut at the lower part of the dispenser.
Disassemble the 3 connectors from the valves.
Unscrew 2 screws from the back of the cabinet.
Unscrew a screw from the TOP BRACKET.
Disassemble two connectors from the POWER
CORD.
Wire Color
Blue Housing (OR-BK)
White Housing (WH-BK)
Blue Housing (GY-BK)
DISPENSER ASSEMBLY
NOISE FILTER
-
7/28/2019 MFL30138908_svc
34/45
-
7/28/2019 MFL30138908_svc
35/45
34
Open the door.
Disassemble the clamp assembly.
Tilt the cabinet cover.
Disconnect the door switch connector.
NOTE: When assembling the CABINETCOVER, connect the connector.
Lift and separate the cabinet cover.
Disassemble the clamp assembly.
Disassemble the Gasket.
-
7/28/2019 MFL30138908_svc
36/45
35
Open the door.
Unscrew the 7 screws from the HINGE COVER.
Put a flat ( - ) screwdriver into the openng of the hinge,and pull out the hinge cover.
Unscrew a screw from the lower side of door.
Disassemble the door upward.
DOOR
Open the door and disassemble the CLAMPASSEMBLY.
Unscrew the 2 screws.
DOOR LOCK SWITCH ASSEMBLY
Be careful! The door is heavy.
NOTE Reconnect the connector after replacing the
DOOR SWITCH ASSEMBLY.
-
7/28/2019 MFL30138908_svc
37/45
36
PUMP
HEATER
THERMISTOR
Disassemble the cabinet cover.
Separate the pump hose, the bellows
and the circulation hose assembly from thepump assembly.
Disassemble the pump assembly in arrow
direction.
Disassemble the cabinet cover.
Separate 2 connectors from the heater.
Loosen the nut and pull out the heater.
Disassemble the cabinet cover.
Unplug the white connector from the thermistor.
Pull it out by holding the bracket of the
thermistor.
CAUTION
When assembling the heater, insert theheater into the heater clip on the bottom ofthe tub.
Tighten the fastening nut so the heater issecure.
-
7/28/2019 MFL30138908_svc
38/45
37
SENSOR ASSEMBLY(BALL SENSOR)
WHEN FOREIGN OBJECT IS STUCK BETWEEN DRUM AND TUB
Disassemble the cabinet cover.
Separate the heater from the tub.
Remove any foreign objects (wire, coin, etc.) by
inserting a long bar in the opening.
Unscrew the 4 screws from the back cover.
Unscrew the single screw from the lower-rightside of the cabinet.
Disconnect the connector from PWB Harness.
-
7/28/2019 MFL30138908_svc
39/45
38
MOTOR/DAMPER
Disassemble the back cover.
Remove the bolt.
Pull out the Rotor.
Unscrew the 2 screws from the tub bracket.
Remove the 6 bolts on the stator.
Unplug the 2 connectors from the stator.
Disassemble the damper hinges from the tuband base.
Separate the dampers.
NOTE Once removed, replace the damper withnew one.
-
7/28/2019 MFL30138908_svc
40/45
39
Disassemble the cabinet cover andcondensing bellows.
Is there any foreign object in condensing
bellows.
Clean the bellows
[dHE] ERROR DISPLAY
CHECK FOR DRY HEATER TROUBLE
CHECK FOR DRY FAN MOTOR TROUBLE
NO
YES
Is the resistance of 2 thermistors on
condensing duct and dry duct
2.5k ~ 180k (at 105C 0C)
Replace the thermistor.
6322FR2046A :
Condensing Duct
6322FR2046B :
Dry DuctYES
NO
Disassemble the dry fan assy and dry duct
upper, and clean foreign object in duct and
fan.
Dry duct
Condensingduct
Condensing bellows
Thermistor
~
-
7/28/2019 MFL30138908_svc
41/45
40
DRY HEATER TROUBLE
After power off, is the resistance of
dry heater 10 ~ 40?Replace the dry heater.
YES
NO
Is thermostat closed?Replace the thermostat.
YES
NO
When checking voltage between connectors
( 1 , 2 ) on drying, is the voltage
AC 120V as the figure?
(Wire color : - Red, - Blue)
Replace the PWB assy
(Main)NO
1 2
-
7/28/2019 MFL30138908_svc
42/45
41
10-1. CABINET & CONTROL PANEL ASSEMBLY
10. EXPLODED VIEW
A495
A485
A455
A410
A152
A150
A450
A110
F210
A151 A153
A130
A140
A133
A310A300
A303A200 A220
A155
A440
A430
A100
A101
A105A104A102
A490
A103
F215
-
7/28/2019 MFL30138908_svc
43/45
42
10-2. DRUM & TUB ASSEMBLY
K344K346 K345
K123
K360K350
K115
F140
K411
K410
K110
K111
K140
K143
K320
K310
K510
K530
K340
F315
F463
F310
K125
K531
K343
K550
F463
F464
K121
K101
K122
K141
K611
K610
F141 K105
K531 K520
F461
K540
-
7/28/2019 MFL30138908_svc
44/45
43
10-3. DISPENSER ASSEMBLY
F225
F300
F220
F323
F330
F321
F322
F160
F340
F329
F430
F441
F435
F120
F130
F440
F436
F431
-
7/28/2019 MFL30138908_svc
45/45
10-4. THE EXPLODED VIEW OF DRYER
M312
M215
M315
M230
M215
M120
M130
M215M312
M310
K310
K230
K220
M101
M240
M210
M110
M100