Metrado de Cargas

8
URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña DISEÑO DE VIGAS POR FLEXIÓN Y CORTANTE; VERIFICACION DE ACERO DE REFUERZO DISEÑO DE COLUMNAS REALIZADO POR: JOE ARROYO SAAVEDRA JEISSON LOPEZ PRADO ALMENDRA SANCHEZ LUDEÑA ALEXANDRA VALENCIA LUNA Generalidades El programa VisualFEA, ha sido creado para el estudio del comportamiento de diferentes estructuras como vigas, pórticos, elementos Shell entre otros para la determinación de reacciones, fuerzas cortas, momentos flectores y deformaciones en la estructura. Introducción El estudio realizado se baso en la estructuración de un pórtico de 5 pisos con todos sus elementos estructurales como vigas principales, vigas secundarias, losas y columnas, siendo estas aplicadas con sobrecargas de diferentes magnitudes para cada piso. Cabe resaltar que el estudio definitivo va ser en consideración al cuarto y quinto piso del pórtico realizado. Overview VisualFEA The program has been created to study the behavior of different structures such as beams, frames, Shell and other elements for determining reactions, short forces, bending moments and deformations in the structure. Introduction The study was based on the structuring of a 5- story porch with all its structural elements as main beams, secondary beams, slabs and columns, these being applied with an overload of different magnitudes for each floor. Significantly, the final study will be considered the fourth and fifth floor of the porch done.

Transcript of Metrado de Cargas

Page 1: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

DISEÑO DE VIGAS POR FLEXIÓN Y CORTANTE; VERIFICACION DE ACERO

DE REFUERZO

DISEÑO DE COLUMNAS

REALIZADO POR:

JOE ARROYO SAAVEDRA

JEISSON LOPEZ PRADO

ALMENDRA SANCHEZ LUDEÑA

ALEXANDRA VALENCIA LUNA

Generalidades

El programa VisualFEA, ha sido creado para el

estudio del comportamiento de diferentes

estructuras como vigas, pórticos, elementos

Shell entre otros para la determinación de

reacciones, fuerzas cortas, momentos flectores

y deformaciones en la estructura.

Introducción

El estudio realizado se baso en la estructuración

de un pórtico de 5 pisos con todos sus

elementos estructurales como vigas principales,

vigas secundarias, losas y columnas, siendo

estas aplicadas con sobrecargas de diferentes

magnitudes para cada piso. Cabe resaltar que el

estudio definitivo va ser en consideración al

cuarto y quinto piso del pórtico realizado.

Overview

VisualFEA The program has been created to

study the behavior of different structures such

as beams, frames, Shell and other elements for

determining reactions, short forces, bending

moments and deformations in the structure.

Introduction

The study was based on the structuring of a 5-

story porch with all its structural elements as

main beams, secondary beams, slabs and

columns, these being applied with an overload

of different magnitudes for each floor.

Significantly, the final study will be considered

the fourth and fifth floor of the porch done.

Page 2: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

Objetivo

Establecer las dimensiones de las vigas

principales y secundarias, junto con las

columnas

Realizar debidamente el metrado de

cargas de las vigas para cada piso

Diseñar por flexión las vigas principales

y secundarias

Verificar si las dimensiones del acero de

las vigas principales y secundarias

necesitan refuerzo.

Hipótesis

Las deformaciones, valores de momentos

flectores, valores de cortantes van a ser de una

mínima magnitud debido a que no estamos

considerando fuerzas de sismos y cargas

adicionales a las que se encuentran por cada

piso.

Con la verificación del acero de refuerzo para

vigas tomaremos en cuenta que si no cumple las

condiciones volveremos a redimensionar la viga

junto con el aumento de área de acero, del

mismo modo se realizara para el diseño de

columnas si es que esta dimensión no esta

dentro del diagraman de interacción siendo

redimensionada la columna.

Target

• Set the dimensions of the main and secondary

beams, along with the columns

• Conduct metrado properly load the beams for

each floor

• Design by bending the main and secondary

beams

• Check the dimensions of the steel joists need

strengthening primary and secondary

Hypothesis

The deformations, values of bending moments,

shear values will be minimal extent because we

are not considering seismic forces and

additional burdens that are on each floor.

With the verification of reinforcing steel for

beams take into account that does not meet the

conditions return to resize the beam with

increasing steel area, just be held for the design

of columns if this dimension is not within

diagrammed interaction of the column being

resized.

Formulación teórica

Se pretende realizar el diseño complete de

vigas, losas y columna con cargas

uniformemente distribuidas para cada piso;

dimensionando asi los elementos estructures

Page 3: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

con acero de refuerzo. El programa VisualFea

nos simplificara el trabajo debido a que este nos

mostrara los diagramas de momentos flector y

cortante para cada piso de la estructura; con

esto realizaremos cálculos para determinar las

dimensiones de los aceros que se colocaran

para cada elemento sirviendo como refuerzo.

Theoretical formulation

They are intended to complete the design of

beams, slabs and column with uniformly

distributed loads for each floor; sizing so you

structure elements with reinforcing steel. The

program VisualFea we simplify the job because

this will show us the bending moment diagrams

and shear for each floor of the structure, with

this we will make calculations to determine the

dimensions of the steel will be placed for each

item serving as reinforcement.

Modelo Matemático de la estructura

(Mathematical model of the structure)

Planta del 1er, 2do y 3er piso

Page 4: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

Planta 4to y 5to Piso

Metrado de Cargas / Sobre Cargas

(Metrado Freight / Cargo On)

La estructura que se muestra soportará las siguientes sobrecargas:

Page 5: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

1er Entrepiso: 200 kg/m2

2do Entrepiso: 350 kg/m2

3er Entrepiso: 500 kg/m2

4to Entrepiso: 400 kg/m2

5to Entrepiso: 150 kg/m2

PARA 4to Y 5to PISO

(4th and 5th FLOOR FOR)

LOSA MACIZA EN UNA DIRECCION:

h 3/30 = 0.10

3/35 = 0.09 Como promedio tomamos h = 0.12 m

4/30 = 0.13

4/35 = 0.11

VIGAS PRINCIPALES (VP)

h 10/10 = 1.00 h = 0.80 m

10/12 = 0.83 b = 0.30 m

VIGAS SECUNDARIAS (VS)

h 3/14 = 0.21 h = 0.30 m

4/14 = 0.29 b = 0.15 m

DIMENSIONAMIENTO DE COLUMNAS

h = 0.30 m

b = 0.80 m

Page 6: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

CARGA MUERTA:

( )

( ) ( )

( )

( )

CARGA VIVA:

( )

( )

( )

( )

CARGA MUERTA:

( )

( ) ( )

( )

( )

CARGA VIVA:

( )

( )

( )

( )

𝐖𝐃 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟒𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟓𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐃 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟒𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟓𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

Page 7: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

CARGA MUERTA:

( )

( ) ( )

( )

( )

CARGA VIVA:

( )

( )

( )

( )

CARGA MUERTA:

( )

( ) ( )

( )

( )

CARGA VIVA:

( )

( )

( )

( )

𝐖𝐃 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟒𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟓𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐃 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟒𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟓𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

Page 8: Metrado de Cargas

URP - Fac. Ingeniería - Escuela de Ingeniería Civil Comportamiento Estructural – Ing. Virgilio Peña

CARGA MUERTA:

( )

( ) ( )

( )

( )

CARGA VIVA:

( )

( )

( )

( )

𝐖𝐃 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟒𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚

𝐖𝐋 (𝟓𝒕𝒐 𝑷𝒊𝒔𝒐) 𝑇𝑜𝑛

𝑚