Metalworking Tools for Marine, Bridge, Pipeline and
Transcript of Metalworking Tools for Marine, Bridge, Pipeline and
2 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
Metalworking Tools for Marine, Bridge,Pipeline and Process Industries
CS Unitec's Trelawny™ line of surface preparation tools features many Vibro-Lo™ models.These models include integrated vibration reduction technology to operate with 7x lessvibration than standard models. Vibration damping components offset the hammer vibrationwhen the tool impacts the workpiece, reducing the risk of vibration-related injury.
Hand-Held Scaling Hammers (Pneumatic) p. 5
• Low-Vibration Single-Head and Triple-Head Scaling Hammers
• Remove thick scale, heavy corrosion, hard coatings and more
• Optional spark-resistant copper beryllium cutter heads
Low-Vibration Needle/Chisel Scalers (Pneumatic) p. 6-9
• Vibro-Lo™ Needle/Chisel Scalers remove coatings, corrosion and other accumulated materials
• Clean and stress-relieve weld seams and joints
• Variety of needles and chisels, including options for use in hazardous areas and Ex zones
Vibro-Lo™Vibration Reduction
Technology
Long-Reach Chisels / Scrapers / Scalers (Pneumatic) p. 10
• Available in lengths ranging from 2' to 6'; chip, scrape and descale with one tool
Surface Preparation Tools & Dust Collection Vacuums
Low-Vibration Steel Deck Hammer (Pneumatic) p. 11
• 11 heads and 33,000 blows per minute• Fracture and reduce scale, corrosion and thick coatings in minutes,
reducing blast media costs
• Ideal for ship decks, tank bottoms, bridge decks, floating platforms and more
Floor Scarifiers / Planers (Electric • Pneumatic • Gas) p. 12
• Ideal for the most demanding surface preparation and material removal applications
• Remove rust, scale, paint, adhesives and more from steel and concrete
Trident Neptune Flexible Shaft Deck Descalers (Air • Electric) p. 13
• Rapidly remove scale, rust, paint and other unwanted deposits on ship decks and othermetal surfaces
Hydraflex Hold Cleaning Gun Kit (Pneumatic) p. 14
• Reach up to 100 ft. away with high-pressure water jet
• Clean hold areas on bulk carriers and cargo vessels of all sizes
• Wet/Dry air-powered models collect dry dust/debris and non-flammable liquids
• ATEX classified, antistatic vacuum and air-supply hose; optional HEPA filter
• Electric-powered wet/dry models with HEPA filtration
Hand-Held Scarifiers – Rotopeen™ (Pneumatic • Electric) p. 4
Dust Collection Vacuums (Pneumatic • Electric) p. 15
• Ideal alternative to small-area shot blasting
• Clean and prepare steel and concrete surfaces
• Available with 3M's Rotopeen™ 'C' flaps, star cutters and beam cutters
Vibro-Lo™Vibration Reduction Technology
Vibro-Lo™Vibration Reduction Technology
Vibro-Lo™Vibration Reduction Technology
CS Unitec's Trelawny™ Rotopeen™ hand-held scarifiersare the ideal alternative to small-area shot blasting forcleaning and preparing steel and concrete surfaces. They utilize 3M's brand of Rotopeen™ 'C' flaps to offer a captive shot method of surface preparation.
• Pneumatic and electric models
• Integrated dust shroud for dust and debriscollection, as well as cleaner, safer removal oflead-based paints and contaminated particles
Peening Preparation Tool (PPT) – idealalternative to small-area shot blasting
Pneumatic Hand-Held Scarifiers
194.0205
194.C205
194.0405
194.C405
30
30
30
30
2700
2700
2700
2700
3.5
6.0
3.1
4.6
ModelNumber
CFM @90 PSI
Speed(RPM)
2"
2"
4"
4"
CuttingWidth
'C' Flaps
Star Cutters
'C' Flaps
Star Cutters
These models are compatiblewith Star Cutters, Beam Cutters
and Rotopeen™ 'C' Flaps
CuttingMedia
7.5
11.5
9
13.25
Weight(lbs.)
VibrationLevels m/s2
Electric Hand-Held Scarifiers
195.1217
195.1220
110V
220V
2000
2000
3.6
3.6
ModelNumber Motor Power
Speed(RPM)
2"
2"
CuttingWidth
'C' Flaps
'C' Flaps
CuttingMedia
10
10
Weight(lbs.)
VibrationLevels m/s2
Applications include:• Aggressive removal of alkyds, adhesives,lead-based paints, mastics, coatingscorrosion and more• Cleaning and preparing steel andconcrete surfaces
Electric Model 195.1220 2" cutting width with Rotopeen™ 'C' flaps
Pneumatic Models 194.0405 and194.C405, 4" cutting width
See page 15 for dustextraction systems.
4 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
Hand-Held Scarifiers - Rotopeen™ Air • Electric
Star Cutter Beam Cutter 3M™ Rotopeen™ 'C' FlapP/N 312.S200 P/N 312.R200 P/N 312.MRPC
Hand-Held Scarifier Accessories
HEAVYSCALING
LIGHTBURNISHING
Nuclear
Ships decks
Construction
Factory Floors
Swimming Pools
Bridge Maintenance
Pipeline Maintenance
––––
Non-slip coatings
Plaster removal
––––
Adhesive removal
Sealant removal
––––
––––
––––
Ceiling / wall paint removal
Floor marking removal
Adhesive removal
––––
––––
Radioactive waste removal/capture
General paint removal
Ceiling / wall paint removal
Floor marking removal
––––
Paint / sealant removal
Protective coating removal
Aggressive removalof thick coatings
Removal of hard coatings, lessaggressive than star cutter
Removal of light paint and rust to bare metal finish
Star CutterCuttingWidth
2"4"
QuantityRequired
80160
Beam CutterCuttingWidth
2"4"
QuantityRequired
56112
Rotopeen™'C' Flap
CuttingWidth
2"4"
QuantityRequired
612
CS Unitec's Trelawny™ line of pneumatic hand-heldscaling hammers are ideal tools for the removal of thickscale, heavy corrosion and hard coatings. Areas ofapplication include pipes, ship decks, oil platforms,storage tanks and bridge structures.
• Single-head scaling hammer includes Vibro-Lo™ vibrationreduction technology
• Optional spark-resistant copper beryllium replacement headsreduce risk of explosion in potentially hazardous areas
• Detachable taper fit cutter head reduces cost of replacementand extends piston life
Remove thick scale, heavycorrosion and hard coatings
Applications Include:• Pipes• Ship Decks• Oil Platforms• Storage Tanks• Bridge Structures
Pneumatic Hand-Held Scaling Hammers
Cruciform
Vibro-Lo™Vibration Reduction
Technology
5• 1-800-700-5919 • Visit our Web site at www.csunitec.com
CS Unitec's Trelawny™ Single-HeadHand-Held scaler operates with 7x lessvibration than standard models. This toolutilizes vibration damping components tooffset the hammer vibration created whenthe head impacts the workpiece.
Pneumatic
Hand-Held Scaling Hammer AccessoriesPart No.
426.5351
606.5303
426.5352
612.5301
For Model Numbers
151.5100, 196.5095and 153.5300
151.5110 and 153.5310
151.5105 and 153.5305
All models shown below
TCT CruciformCutter Head
Copper Beryllium(CuBe) Cruciform Cutter Head
Bush Cutter Head
Common TaperedPiston
Vibro-Lo™
Pneumatic Hand-Held Scaling Hammers
Low-VibrationSingle Head
Triple Head
TCT Cruciform Piston
Bush Hammer Piston
CuBe Cruciform Piston
TCT Cruciform Piston
TCT Cruciform Piston
Bush Hammer Piston
CuBe Cruciform Piston
151.5100
151.5105
151.5110
196.5095
153.5300
153.5305
153.5310
5.5
5.5
5.5
5.5
8
8
8
3000
3000
3000
3000
9000
9000
9000
7
7
7
7
7
7
7
88.1
88.1
88.1
88.1
88.1
88.1
88.1
6.8
6.8
6.8
3.7
13.4
13.4
13.4
19" x 6"
19" x 6"
19" x 6"
19" x 5.5"
19" x 6"
19" x 6"
19" x 6"
DescriptionModelModelNumber
Weight(lbs.)
Dimensions(LxH)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
SingleHead
Vibro-Lo™
Pneumatic Hand-Held Scaling Hammers
Copper Berylliumfor use in potentiallyexplosive areas
H
H
H
Bush
VL223
VL203
CS Unitec's Trelawny™ line of Low-Vibration needle/chiselscalers offer high performance and low vibration forgreater productivity and improved operator comfort.Ergonomically designed with low maintenance and quickchange tooling option.
CS Unitec's Trelawny™ Vibro-Lo™ line of Needle/ChiselScalers operate with 7x lessvibration than standardmodels. These tools utilizevibration damping componentsto offset the hammer vibrationcreated when the needles/chiselsimpact the workpiece.
• Integrated Vibro-Lo™ vibration reduction technology
• Lightweight, easy to handle
• Optional dust shroud for dust and debris collection
• Tool-free needle changeover
• Converts to chisel scaler in seconds
High power with low vibration –equipped with Vibro-Lo™
Applications include:• Cleaning and stress-relieving weld seams and joints• Removing coatings, corrosion and other accumulated materials• Texturing concrete• Splitting, chipping, pointing and brick raking
VL303
Needle Scalers andChisel Scalers convert in
seconds with optionalhead or when purchased
as a Kit. See followingpage for Kit information.
6
Low-Vibration Needle/Chisel Scalers Vibro-Lo™Vibration Reduction
Technology
Dust CollectionShroud
CS Unitec's Vibro-Lo™ Needle/Chisel Scalers are a safer, more effectivemeans of removing coatings, corrosion and other accumulated materials.Vibro-Lo reduces the risk of vibration-related injury.
Chisel for light surface marking
Flat for light treatmentand polishing effect
Pointed for veryhard scale
Copper Berylliumfor use in potentiallyexplosive areas
Stainless Steel for usein applications wherecorrosion or humidity is aproblem, such as foodprocessing industry
See page 9 for thefollowing types ofneedles:
Chisels for Vibro-Lo™ Chisel Scalers
Dust Collection Shroud for Vibro-Lo™ Needle Scalers
Shank Length Width Application
Pistol
VL223 Needle Scaler
VL223 Needle Scalerwith dust shroud
Chisel Part Number
Square
SquareCranked End
Square
Square
Square
7"
7"
7"
7"
10"
2"
3/8"
3/4"
2-1/2"
3/4"
Spark resistant Aluminum Bronzefor use in hazardousareas
Weld flux and thick coating removal
Weld splatter removal
Wide flat chisel forthe removal of rustor peeling paint
Flat chisel for weldsplatter and sand cast cleaning
704.3110
704.3205
704.3101
704.3103
704.3107
DescriptionGripModelNumber
Needle Quantity/Diameter
Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Optional Dust Shroud for Needle Scalers – for use with dust extraction vacuums.Model VL223 Needle Scaler – Order Dust Shroud P/N 418.2003Model VL203 Needle Scaler – Order Dust Shroud P/N 418.2003Model VL303 Needle Scaler – Order Dust Shroud P/N 418.3003
VL223 Kit – Order P/N 199.2113VL203 Kit – Order P/N 199.2105VL303 Kit – Order P/N 199.3103
CS Unitec offers Vibro-Lo™ Needle/Chisel Scaler Kits, each supplied with the Needle Scaler, 3mm needles, a chisel holder, anvil and a 3/4" blade chisel.
Vibro-Lo™ Needle Scalers
Vibro-Lo™ Chisel Scalers Vibro-Lo™ Needle/Chisel Scaler Kits
CS Unitec offers a drop protection kit for our Vibro-Lo™ Needle/ Chisel Scalers. Protect your investment when working at heights or in applications where dropping/ losing the tool is likely, including: offshore platforms and rigs, bridges/ scaffolding, vessels and ships.
For VL223 and VL203Order P/N 720.2003*
For VL303Order P/N 720.3003** Safety clip and line not supplied
Drop Protection Kit
Inline
Pistol
VL223 Chisel Scaler
VL203 Chisel Scaler
VL303 Chisel Scaler
199.2213
199.2203
199.3203
6.5
7
9.5
2400
2400
3000
4
4
5.5
76.3
76.3
78.2
3.69
3.33
3.7
DescriptionGripModelNumber
Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Inline
H
H
199.2103
139.2103
199.2003
199.2303
199.3003
199.3005
19 / 3mm
19 / 3mm
19 / 3mm
19 / 3mm
28 / 3mm
28 / 3mm
5.25
5.25
6
6
7.75
7.75
2400
2400
2400
2400
3000
3000
4
4
4
4
5.5
5.5
90.7
90.7
90.7
90.7
109.5
109.5
2.56
2.56
2.75
2.75
2.3
2.3
VL203 Needle Scaler
VL203 Needle Scalerwith dust shroud
VL303 Needle Scaler
VL303 Needle Scalerwith dust shroud
CS Unitecoffers a fullline of non-sparking,non-magneticchisels andsafety handtools forhazardousareas and Exzones.Contact usfor details.
See page 15 for dustextraction systems.
7• 1-800-700-5919 • Visit our Web site at www.csunitec.com
Vibro-Lo™Vibration Reduction
Technology
Low-Vibration Needle/Chisel Scalers
8 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
Standard Needle/Chisel Scalers
Chisel for light surface marking
Flat for light treatmentand polishing effect
Pointed for veryhard scale
Copper Berylliumfor use in potentiallyexplosive areas
Stainless Steel for usein applications wherecorrosion or humidity is a problem, such as the food processing industry
See page 9 forneedles:
Chisels for Standard Chisel Scalers1/2" Square Connection
Shank Length Width Application
Pistol
SemiPistol
1B Needle Scaler1B Chisel Scaler
2B Needle Scaler2B Chisel Scaler
Square
SquareCranked End
Square
Square
Square
Square
Square
7"
7"
7"
7"
10"
8"
7"
2"
3/8"
3/4"
2-1/2"
3/4"
1/4"
Moil Point
Spark-resistant Aluminum Bronzefor use in hazardous areas
Weld flux and thick coating removal
Weld splatter removal
Wide flat chisel for the removalof rust or peeling paint
Flat chisel for weld splatterand sand cast cleaning
Mortar removal for repointingbrick work
Concrete chipping
704.1110
704.2105
704.1101
704.1103
704.1107
704.1106
704.1112
DescriptionGripModelNumber
Needle Qty./Dia.
Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Dust Collection Shroud for Standard Needle ScalersOptional Dust Shroud for Needle Scalers – for use with dust extraction vacuums.Model 2B and 2BPG Needle Scalers – Order Dust Shroud P/N 418.2199Model 3BPG Needle Scaler – Order Dust Shroud P/N 418.3039
* 3BPG Chisel Scaler 135.3395 has 5/8" hexagonal chisel holder and is compatible with chisels shown on page 10. All others Chisel Scalers shown above have 1/2" square connection.
Standard Needle and Chisel Scalers
TVS™ Needle Scalers with Integrated Vacuum Shroud
Inline
H
H
12 / 3mmN/A
19 / 3mmN/A
3.53.3
5.754.4
38003800
30003000
3.03.0
5.55.5
110.498.9
113.398.6
8.58.2
9.317.4
123.2199125.2300
133.3199135.3300135.3395
19 / 3mmN/A
28 / 3mmN/AN/A
5.754.5
8.256.26.2
30003000
220022002200
5.55.5
8.08.08.0
113.398.6
114.5105.1105.1
12.622.4
18.925.625.6
131.3099134.3200
141.4099144.4200
28 / 3mmN/A
35 / 4mmN/A
107.5
12.58.2
22002200
18001800
8.08.0
8.58.5
114.5105.1
117.4105.1
2BPG Needle Scaler2BPG Chisel Scaler
3BPG Needle Scaler3BPG Chisel Scaler3BPG Chisel Scaler*
3B Needle Scaler3B Chisel Scaler
4B Needle Scaler4B Chisel Scaler
Pistol
2B Needle Scaler
DescriptionGripModelNumber
Weight(lbs.)
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
Inline 139.2007 6.4 3000 5.5 98.6 17.4
139.2107
139.3107
6.6
9.9
3000
2200
5.5
8.0
98.6
105.1
22.4
19.9
2BPG Needle Scaler
3BPG Needle Scaler
CS Unitec's Trelawny™ TVS™ Needle Scalers with Integrated VacuumShroud enable dust-free working in hazardous applications when usedwith a dust extraction vacuum (see page 15 for dust collection systems).
Pistol Grip
Semi PistolGrip
Above: Model 1B Chisel Scalerwith Square Cranked End Chisel
for removal of flux
CS Unitec offers afull line of non-sparking, non-magnetic chiselsand safety handtools for hazardousareas and Exzones. Contact usfor details.
Standard Needle Scalers and ChiselScalers convert in seconds with optional
head or when purchased as a Kit.Contact us for more information.
111.1099114.1200
121.2099124.2200
Inline Grip
12.219.9
23.545.2
Chisel Part No.
9• 1-800-700-5919 • Visit our Web site at www.csunitec.com
Available in 3mm flat top only; for use in potentiallyhazardous areas.
Needles
Flat Tip
2mm
2mm
2mm
2mm
2mm
3mm
3mm
3mm
3mm
3mm
3mm
4mm
4mm
4mm
4mm
3mm
3mm
6 x sets of 29 needles
6 x sets of 51 needles
6 x sets of 65 needles
Box of 100 needles
Box of 2000 needles
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles (180mm long)
6 x sets of 19 needles
6 x sets of 35 needles
Box of 50 needles
Box of 500 needles
Box of 1000 needles 5" long (127mm)
19 x needles 5" long (127mm)
412.1129
412.1151
412.1165
452.1110
442.1107
413.1112
413.1119
413.1128
413.1149
453.1110
443.1107
414.1119
414.1135
454.1105
444.1107
443.1105
443.1115
Flat-tipped needles will reduce markingon metal surfaces and can give apolishing effect. For use on thin gaugemetals and any surface where a lighttreatment is required.2mm needles used on a welded joint produce a similareffect to shot peening, reducing stress in the weld.
Size Description Part #
Chisel Tip
3mm
3mm
3mm
3mm
3mm
3mmConversions:2mm = 0.08"
3mm = 0.12"
4mm = 0.16"
180mm = 7"
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles
413.2112
413.2119
413.2128
413.2149
453.2110
443.2107
These needles will clean the samematerials as a pointed tip, but will leavelight surface marking
Size Description Part #
Pointed Tip
3mm
3mm
3mm
3mm
3mm
3mm
4mm
4mm
4mm
4mm
6 x sets of 12 needles
6 x sets of 19 needles
6 x sets of 28 needles
6 x sets of 49 needles
Box of 100 needles
Box of 1000 needles
6 x sets of 19 needles
6 x sets of 35 needles
Box of 50 needles
Box of 500 needles
413.3112
413.3119
413.3128
413.3149
453.3110
443.3107
414.3119
414.3135
454.3105
444.3107
Sharpened to a conical point, these arethe most effective in breaking throughvery hard scale on materials where somesurface indentation is permissible - or where aroughening or keying of the surface is actuallydesirable.
Size Description Part #
3mm
3mm
3mm
3mm
3mm
3mm
Box of 12 needles
Box of 19 needles
Box of 28 needles
Box of 49 needles
Box of 100 needles
Box of 500 needles
403.1312
403.1319
403.1328
403.1349
453.1310
443.1307
Size Description Part #
Spark-Resistant Copper BerylliumH
Available in 3mm flat tip form only, to be used inapplications such as refurbishment of food processingmachinery or areas of high humidity where the corrosiveeffect on needles would be prohibitive.Used on decorative concrete surfaces where contamination of thesurface from carbon steel needle is undesirable.
3mm
3mm
Box of 100 needles
Box of 500 needles
453.1207443.1207
Size Description Part #
Stainless Steel
See page 15 fordust extractionsystems.
CS Unitec's Trelawny™ needles last 10x longer than standard needles. Save time and money with fewer needle changes and less downtime.
All of CS Unitec's Needle Scalers are delivered from stock complete with 180mm long x 3mm diameter chisel tipped high performance needles. Other needle holders are available as accessories for use with 2mm and 4mm diameter needles. We also offer spark resistant needles for use in potentially hazardous areas and Ex zones, as well as stainless steel needles for usein humid areas - such as applications in the food processing industry - where corrosion is a concern.
Standard pack set is one carton of 6 sets. Some models are packed as an individual set in a box.Boxes of 100 qty. needles in a durable, reusable plastic container are available, as well as largerquantities.
Long-Reach Chisels/Scrapers
StandardScalers
LITEScalers
2ft. Chisel4ft. Needle4ft. Chisel5ft. Chisel
4ft. Chisel5ft. Chisel6ft. Chisel
136.3299137.3400136.3499136.3599
136.3497136.3597136.3697
8111112
6.757.58.5
2200220022002200
220022002200
Model DescriptionModelNo.
Weight(lbs.)
4.54.54.54.5
4.54.54.5
841048486
898984
CFM@ 90PSI
Blows per
minute
Noise Leveldb(A)
Chisel Accessories
Needle Scaler Accessories
Scraper Accessories
• Ice• Residue• Adhesive• Asbestos• Linoleum• Carpeting• Plaster
• Mortar• Floor tiles• Metal slag• Rubber coatings• Roofing materials• Chemical spillages• Bituminous products
Applications include removal of:
CS Unitec’s Trelawny™ Long-Reach Scrapersfeature one tool with multiple applications.
• Available in 2', 4', 5' and 6' lengths• Three tools in one – chipper, scraper and descaler• Quick-change chisel release• Low air consumption• Standard and "LITE" models
Chip, scrape and descalewith one versatile tool
Chipping Scraping Descaling
705.1100
705.1101
705.1102
705.1106
705.1112
705.2102
708.1101
9"
9"
8"
9"
8"
8"
1"
2"
1"
4"
2"
4"
4"
1-1/8" comb insert
Spark-resistant aluminum bronzefor use in hazardous areas
Flat chisel for sand cast chipping
Asphalt cutter / paint removal /general chipping applications
Removal of linoleum from floor base
Spark resistant aluminum bronzefor use in hazardous areas
Floor tile removal
Brick cleaning and reclamation (usewith 8" long comb holder 708.1100)
ChiselPart No.
ChiselLength
Blade Width Applications
H
H
All long-reach scrapers are available as needlescalers by changing the scraper/chisel with theneedle attachment P/N 415.3532. See page 9for needles.
Flat
431.3504
431.3508
431.3512
Beveled
431.3904
431.3908
431.3912
439.3504(5 Blades)
439.3508(5 Blades)
439.3512(4 Blades)
439.3524(5 Blades)
439.3528(5 Blades)
439.3522(4 Blades)
Adhesive andpaint build up
removal
Paint andcoatingspillageremoval
Carpet andtile removal
Stubbornadhesiveremoval
Carpet andtile removal
Adhesiveremoval
4"
8"
12"
4"
8"
12"
ScraperAssemblyPart No.
BladePack
BladeWidth
Applications
10 • 1-800-700-5919 • Visit our Web site at www.csunitec.com
Long-Reach Chisels/Scrapers/Scalers
11• 1-800-700-5919 • Visit our Web site at www.csunitec.com
Applications Include:• Ship Decks• Tank Bottoms• Bridge Decks• Floating Platforms
CS Unitec's Trelawny™ ScaleForce Eleven Pneumatic Deck Hammer operates with 7x less vibration thanstandard models. This tool utilizes vibration dampingcomponents to offset the hammer vibration createdwhen the heads impact the workpiece.
SF11 Steel Deck Hammer
CS Unitec's Trelawny™ ScaleForce Eleven Pneumatic DeckHammer will fracture and reduce scale, corrosion and thickcoatings in minutes. The machine's low profile body andadjustable handle mean the deck hammer needs only 6"clearance for working under pipes and other constructions.
• Includes Vibro-Lo™ vibration reduction technology
• Optional spark resistant beryllium copper replacement headsto reduce risk of explosion in potentially hazardous areas
• Detachable taper fit cutter head reduces cost of replacementand extends piston life
• Optional vacuum shroud reduces hazardous and nuisancedust when used with TVS approved dust collectors
11 heads deliver 33,000 BPM Fracture and reduce scale, corrosionand thick coatings in minutes – andreduce blast media costs
11 heads provide 33,000 BPM (11 x 3000 BPM)
Vibro-Lo™Vibration Reduction
Technology
SF11 AccessoriesPart No.
426.5351
606.5303
426.5352
612.5301
437.0100
Cruciform Cutter Head
Copper Beryllium (CuBe)Cruciform Cutter Head
Bush Cutter Head
Common Tapered Piston
Vacuum Shroud
Vibro-Lo™
Vibro-Lo™
Vibro-Lo™
ScaleForce Eleven (SF11) Pneumatic Deck Hammer
SF11 w/ CuBeHeads
SF11 w/ DustShroud
159.5910
159.5930
159.5912
ModelNumber
79
79
83
11.1" x 47.6"
11.1" x 47.6"
11.1" x 47.6"
Weight(lbs.)
Dimensions(WxH)
10"
10"
10"
70
70
70
113.1
113.1
113.1
5.76
5.76
5.76
33,000
33,000
33,000
CuttingWidth
Blows per
minuteCFM @90 PSI
Noise Leveldb(A)
VibrationLevelsm/s2
SF11 w/CruciformHeads
Copper Beryllium for use in potentially explosive areas H
H
Bush Cruciform Optional dust shroud,P/N 437.0100, tocollect dust and debriswhen connected to adust collectionvacuum.
See page 15 for air-powereddust collection vacuum – ATEXclassified for use in Gas Zone 2and Dust Zone 22.
• 1-800-700-5919 • Visit our Web site at www.csunitec.com12
Applications include:• Removal of rust, scale, paint, adhesives and more • Keyed or grooved profiles• Roughing concrete
CS Unitec's Trelawny™ Floor Planers tackle the most demandingsurface preparation and material removal applications. Ideal for theremoval of coatings and corrosion from steel and concrete surfacesto prepare for re-coating. Produce an ideal keyed or grooved profileon concrete for waterproofing and non-slip surface applications.
• Depth control maximizes performance and extends cutter life
• Integrated vacuum connection and hold-to-run handle
• Fully adjustable handlebar for operator comfort
• Electric, pneumatic or gas power
Remove rust, scale, paint, adhesivesand more from steel and concrete
Floor Scarifiers / Planers Electric • Pneumatic • Gas
TFP 200 Floor Scarifiers
320.2004T
320.2012T
14" x 35" x 35"1/8"
Model NumberWeight(lbs.)
220V - 240V, 3 HP 8"
CuttingWidth
Dimensions(WxLxH)
Max CuttingDepth per Pass
TFP 200 Electric
14" x 35" x 35"1/8"165CFM @ 90 PSI, 3.5 HP
Motor Specifications
8"
149
99
TFP 200 Pneumatic
320.2000T 14" x 35" x 35"1/8"Honda GX160 Gas, 5.5 HP 8" 130
TFP 200 Gas
TFP 200 Cutters IndividualCutter
N/A
320.5120
320.3658
320.5500
320.5600
320.5650
320.5500
DrumAssembly
320.9620
320.1020SB
320.1020SS
320.1020ST
320.1020SM
320.1020SM
320.002G
Wire Brushes
Beam Cutters
Star Cutters
Tungsten Carbide Tipped Cutters
Milling Cutters (22mm)
Milling Cutters (11mm)
Tungsten Carbide Tipped Cutters(for grooving)
Cutter Applications:
Wire Brushes are ideal for finishcleaning and polishing on steel; canbe used for light concrete deposit.
Beam Cutters are ideal for lightpaint/corrosion removal, withminimal damage to substrate.
Star Cutters are ideal for theremoval of mastics and rubberizedcoatings.
Tungsten Carbide Tipped Cutters are ideal for aggressiveapplications such as roughing concrete and heavy corrosion removal,as well as grooving roadways for non-slip surface.
Milling Cutters are ideal for the removal of plastic road markingswithout penetrating the surface.
TFP 200Electric
TFP 200Pneumatic
TFP 200Gas
• 1-800-700-5919 • Visit our Web site at www.csunitec.com 13
Trident Neptune Flexible Shaft Deck Descalers
Applications Include:• Removal of scale, rust, paint and other deposits• Preparation of surfaces for priming, painting or coating
Standard equipment includes: 9' x 5/8" flexible shaft; heavy-duty leaf scaling head; 6-cutter scaling head; 6" dia. power brush, spanner set and hand guard.
Trident Neptune Deck Descaler Accessories
Trident Neptune Deck Descalers
Electricw/ Swivel Base
Electricw/ Skid Base
340.490/S
340.TN/50/S
340.TN/100/S
340.TN/S/110
340.TN/S/220
3000
2850
3450
2850
3450
75
75
75
106" x 8.3" x 11.4"
106" x 8.3" x 11.4"
106" x 8.3" x 11.4"
ModelModelNumber
55.077.00
55.077.00
55.077.00
55.077.00
55.077.00
ISSANumber
59 12 81
59 12 41
59 12 42
59 12 41
59 12 42
IMPANumber
68 CFM @ 90 PSI1.5 HP
110V / .75 HP
220V / .75 HP
110V / .75 HP
220V / .75 HP
MotorSpecifications
Weight(lbs.)
Dimensions(LxWxH)
CutterSpeed(RPM)
Pneumaticw/ Swivel Base
6-Cutter Scaling Head Part No: 340.581 ISSA: 55 082 01 IMPA: 59 12 86
Heavy Duty Scaling Head Part No: 340.550 ISSA: 55 078 01 IMPA: 59 12 75
Wire Brushes
Flexible Shaft with Handpiece and Coupling Part No: 340.285 ISSA: 55 077 01 IMPA: 59 12 99
Cutter WheelPart No: 340.332ISSA: 55 082 04IMPA: 59 12 89
ReplacementParts:
ReplacementParts:
Side Plates (2 qty.)Part No: 340.575/2ISSA: 55 082 02IMPA: 59 12 87
Cutter PinPart No: 340.583ISSA: 55 082 05IMPA: 59 12 90
Center BoltPart No: 340.581/AISSA: 55 082 03IMPA: 59 12 88
Chipping LeafPart No: 340.347ISSA: 55 078 06IMPA: 59 12 79
Side Plates (2 qty.)Part No: 340.551/2ISSA: 55 078 02IMPA: 59 12 76
Cutter PinPart No: 340.553ISSA: 55 078 05IMPA: 59 12 80
Center BoltPart No: 340.552ISSA: 55 078 03IMPA: 59 12 77
Spacing Washer (50 qty.)Part No: 340.5849/50ISSA: 55 078 04IMPA: 59 12 78
6" Power BrushPart No: 340.160ISSA: 55 084 03IMPA: 59 12 93
Center BoltPart No: 340.558ISSA: 55 084 04IMPA: 59 12 94
6" Twisted Knot BrushPart No: 340.163ISSA: 55 084 01IMPA: 59 12 91
Center BoltPart No: 340.559ISSA: 55 084 02IMPA: 59 12 92
Crimped Wire Cup BrushPart No: 340.166ISSA: 55 084 07IMPA: 59 12 97
Center BoltPart No: 340.557ISSA: 55 084 06IMPA: 59 12 96
Twisted Knot Cup BrushPart No: 340.167ISSA: 55 084 05IMPA: 59 12 95
Center BoltPart No: 340.557ISSA: 55 084 06IMPA: 59 12 96
CS Unitec's Trelawny™ Trident Neptune Deck Descaler is idealfor the rapid removal of scale, rust, paint and other unwanteddeposits on ship decks and other metal surfaces, leaving areceptive surface for priming/painting or coating application.
• Lightweight and portable
• 9' x 5/8" flexible shaft for wide coverage area
• Motor overheat protection on electric models
• Unique non-corrosive D-coupling with positive locking mechanism
• Two-skid base design keeps unit stable and upright; optional swivel base available
Ideal for rapidly removing scale, rust, paint and other unwanted deposits
• 1-800-700-5919 • Visit our Web site at www.csunitec.com14
Hydraflex Hold Cleaning Gun Kit
Specifically designed for hold cleaning on bulk carriersand cargo vessels of all sizes
The Hydraflex uses a combination of water and compressed air for a powerful,high-pressure jet of water that can reach up to 100 ft. away.
• One-man operation
• Constructed of high-quality, non-corrosivestainless-steel materials to prevent corrosion
• Adjustable air and water pressure control valve
Item Model Part No. ISSA No. IMPA No. Weight (lbs.)
1 Gun 342.HY01 55.085.01 59 07 42 12
2 Tripod 342.HY02 55.085.02 59 07 42 21
3 Water Hose Coupling 342.HY03 – – 4.3(2-1/2" x 2-1/2")
4 Water Hose Coupling 342.HY04 – – 0.75(2-1/2" x 2")
5 Instantaneous Water 342.HY05 – – 0.66Hose Adapter
6 Ball Valve 342.HY07 – – 3.10
7 Base Assembly 342.HY60A – – 14.4
Hydraflex Hold Cleaning Gun Accessories
1
2
6
7
Hydraflex Hold Cleaning Gun Kit
ModelModelNumber
ISSANumber
IMPANumber
70 CFM @ 90 PSI
70 CFM @ 90 PSI
342.HY50
342.HY50T
55.085.00
–
55 07 00
–
42
52
10-18kg
10-18kg
MotorSpecifications
Weight(lbs.)
85 psi
85 psi
WaterPressure
2"
2"
WaterHose
3/4"
3/4"
AirHose
Recoil
StandardKit withoutBase
(includes items1, 2, 3, 4 & 5)
CompleteKit withBase
(includes items1, 2, 5 & 6)
Model CS 1445 H(shown at left)
automatically"pulse" cleans filterswithout interruptingoperation!
• Antistatic vacuum and air supply hose
• ATEX classified* Ex II 2 GcT6 foruse in Gas Zone 2 and Dust Zone 22
• Robust stainless steel construction
• Floor tool kit for general cleaning work
• Double filtration with optional 14"Permaflow filter
• Optional HEPA filter – for collection of hazardous dust
• Disposable paper filter or reusablecloth bag for wet use
• 1-800-700-5919 • Visit our Web site at www.csunitec.com
Collection of dry dust/debris and non-flammable liquidsATEX classified; antistatic vacuum and air-supply hose
Air-Powered Dust Collection Vacuum – KAV 30 AIR
Optional Filter BagsPaper filter bags for CS 1225 and CS 1445 - P/N 416014 (5-pack)Plastic filter bags for CS 1225, CS 1445 and CS 1500 - P/N 421742 (5-pack)Paper filter bags for CS 1500 - P/N 416021 (5-pack)Slurry filter bags for CS 1500 - P/N 420592 (3-pack)
CS 1225 H
CS Unitec's wet/dry dust extraction vacuumsoffer strong 130 CFM air flow and an electromagnetic pulse filter cleaning system to maximize vacuum power and dust collection.
• Ideal for use with power tools• 99.999% HEPA filtration efficiency of particles
down to 0.3 microns; automatic filter cleaning • "Power Take Off" outlet activates the vacuum
ON/OFF from the power tool switch
• Non-HEPA models available, 99.930% filtration efficiency
• Kit available to connect two power tools (P/N 198804)
Electric-Powered Dust Collection Vacuums with HEPA Filtration
"Powertake-off"outlet
HEPA Vacuum SpecificationsCS 1225 H CS 1500 H
Power 11 Amp 11 Amp 11 Amp
Air flow 130 CFM 130 CFM 130 CFM
Tank capacity 6.6 gal. 13 gal. 9 gal.
Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.
Filter P/N (2pk.) 428956 428956 428956
CS 1445 H
KAV 30 AIR Vacuum SpecificationsDry Model
303.10KAV30/DWet/Dry Model
303.10KAV30/WD
CFM @ 90 PSI 35 35
Output flow 70 CFM 70 CFM
Tank capacity 6.8 gal. 6.8 gal.
Weight 32 lbs. 32 lbs.
Paper Filter P/N (10pk.) 303.1030 303.1030
HEPA Filter P/N 303.1060 303.1060
Standard Vacuum SpecificationsCS 1225 CS 1500
Power 11 Amp 11 Amp 11 Amp
Air flow 130 CFM 130 CFM 130 CFM
Tank capacity 6.6 gal. 13 gal. 9 gal.
Weight 24.3 lbs. 35.2 lbs. 24.3 lbs.
Filter P/N (2pk.) 416069 416069 416069
CS 1445
15
We make no claim that use of a vacuum will eliminate contaminants. Wear an approved respirator mask and follow all appropriate OSHA safety regulations forproper ventilation, dust handling, eye protection, etc. when using a dust extraction grinder and vacuum.
Dust Collection Vacuums Pneumatic • Electric
Optional Filters, Bags and Accessories for KAV 30 AIRAntistatic standard filter assembly (dry use w/paper filter or bag) - P/N 303.1025/ASPermaflow filter for secondary filtration - P/N 303.1035Antistatic float assembly for wet use - P/N 303.1050/ASDisposable, sealable paper bags for waste such as hazardous dust - P/N 303.1005 (10-pack)
KAV 30 AIR - Dry Model Part No. 303.10KAV30/DStandard equipment includes:Antistatic 38mm tool kit w/
dusting brush (P/N 303.1085/AS)Antistatic cloth filter (P/N 303.1025/AS)K6 paper filters (10pk.) (P/N 303.1030)
The ATEX Directive 94/9/EC (ATEX Group-95) was established toprovide technical and quality objectives to control explosiveatmospheres, as well as the standards for equipment andprotective systems used in such areas. Recognized internationally,tools with ATEX classification provide safety assurances to usersthat the product was manufactured to high levels of safety.
Four ATEX classification elements are used to ensure equipmentis appropriate for its intended purpose and application.
For more information on these classification elements, as wellas the ATEX Directive and Ex zones, visit www.csunitec.com.
*ATEX Classified power tools ensure a high level ofsafety in Ex zones and hazardous atmospheres.
KAV 30 AIR - Wet/Dry Model Part No. 303.10KAV30/WDStandard equipment includes:Antistatic float assembly (P/N 303.1050/AS)Antistatic 38mm tool kit (P/N 303.1095/AS)Antistatic cloth filter (P/N 303.1025/AS)K6 paper filters (10pk.) (P/N 303.1030)