07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF WITHMETAL COVERING AT EAVE A-1

ICE DAM PROTECTION AS

PRESCRIBED BY LOCAL

BUILDING CODE.

1/8-INCH GAP RECOMMENDED AT

PANEL EDGES UNLESS

OTHERWISE PROVIDED BY

MACHINED PROFILED EDGES

ROOF ASSEMBLY

METAL ROOF COVERING

ZIP SYSTEM SHEATHING

ROOF TRUSS

SOFFIT VENT

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® ROOF W/ METAL AT EAVE FORBRICK WALL ASSEMBLY A-2

CODE APPROVED FLASHING

TOP EDGE OF FLASHING

TAPED TO WALL SHEATHING

WITH ZIP SYSTEM TAPE OR

ADHESIVE BACKED FLASHING.

(MUST MEET AC148)

CODE APPROVED FLASHING

LAPPED OVER STANDING

SEAM METAL ROOF

WALL ASSEMBLY

VINYL/WOOD/FIBER CEMENT SIDING (INSTALLED IN

ACCORDANCE WITH CLADDING MANUFACTURER'S

INSTALLATION RECOMMENDATIONS)

ZIP SYSTEM SHEATHING

WOOD OR LIGHT GAUGE METAL STUDS

TOP EDGE OF FLASHING TAPED TO

WALL SHEATHING WITH ZIP SYSTEM

TAPE OR ADHESIVE BACKED

FLASHING. (MUST MEET AC148)

ADHESIVE BACKED FLASHING

RECOMMENDED (MUST MEET AC148)

ROOF ASSEMBLY

METAL ROOF COVERING

ROOF UNDERLAYMENT

PLYWOOD OR OSB SHEATHING

ROOF TRUSS OR RAFTERS

ADHESIVE BACKED

FLASHING RECOMMENDED

(MUST MEET AC148)

ROOF UNDERLAYMENT

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

TYPICAL FELT ROOF W/ METAL INTO ZIPSYSTEM® SHEATHING-WALL ABOVE A-4

CODE APPROVED FLASHING

CODE APPROVED

FLASHING LAPPED

OVER STANDING SEAM

METAL ROOF

ROOF ASSEMBLY

METAL ROOF COVERING

ZIP SYSTEM SHEATHING

ROOF TRUSS OR RAFTER

WALL ASSEMBLY

VINYL/WOOD/FIBER CEMENT SIDING (INSTALLED IN

ACCORDANCE WITH CLADDING MANUFACTURER'S

INSTALLATION RECOMMENDATIONS)

BUILDING PAPER/HOUSEWRAP

PLYWOOD OR OSB SHEATHING

WOOD OR LIGHT GAUGE METAL STUDS

BUILDING PAPER/HOUSEWRAP

ADHESIVE BACKED FLASHING

RECOMMENDED (MUST MEET AC148)

ADHESIVE BACKED

FLASHING RECOMMENDED

(MUST MEET AC148)

BUILDING PAPER/HOUSEWRAP

LAPPED OVER FLASHING

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF W/ METALINTO WATER RESISTANT BARRIER WALL ABOVE A-5

ROOF ASSEMBLY

ASPHALT-FIBERGLASS

SHINGLES

ZIP SYSTEM SHEATHING

ROOF TRUSS OR RAFTERS

METAL RIDGE CAP VENT

CUT BACK ZIP SYSTEM

TAPE PRIOR TO

INSTALLATION OF RIDGE

VENT (OPENING SIZE

BASED ON RIDGE VENT

MANUFACTURER'S

RECOMMENDATIONS)

ZIP SYSTEM TAPE

INSTALLED AT RIDGE

FOR TEMPORARY

DRY-IN

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING ROOF WITHMETAL AT RIDGE VENT A-6

FOLLOW SKYLIGHT

MANUFACTURER'S

RECOMMENDED

FLASHING/WATERPROOFING

DETAILS

ROOF ASSEMBLY

METAL ROOF COVERING

ZIP SYSTEM SHEATHING

R

O

O

F

S

L

O

P

E

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF WITHMETAL AT SKYLIGHT A-7

1/8-INCH GAP RECOMMENDED AT

PANEL EDGES UNLESS

OTHERWISE PROVIDED BY

MACHINED PROFILED EDGES

.

TOP EDGE OF FLASHING TAPED TO

WALL SHEATHING WITH ZIP SYSTEM

TAPE OR ADHESIVE BACKED

FLASHING. (MUST MEET AC148)

ZIP SYSTEM TAPE OR ADHESIVE

BACKED FLASHING (MUST MEET

AC148) INSTALLED AT JOINT

BETWEEN ZIP SYSTEM WALL AND

ROOF SHEATHING*

1/8-INCH GAP RECOMMENDED AT

PANEL EDGES UNLESS

OTHERWISE PROVIDED BY

MACHINED PROFILED EDGES

CODE APPROVED

FLASHING

METAL ROOF COVERING -

FASTEN PER CODE USING

FASTENERS COMPATIBLE

WITH SPECIFIC METAL

ROOF COVERING.

WALL ASSEMBLY

ZIP SYSTEM SHEATHING

WOOD OR LT. GA. METAL STUDS

ZIP SYSTEM SHEATHING (ROOF).

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM SHEATHING W/ METAL COVERINGAT WALL TO ROOF TRANSITION A-8

ZIP SYSTEM TAPE*

METAL VALLEY FLASHING

METAL ROOF COVERING -

FASTEN PER CODE USING

FASTENERS COMPATIBLE

WITH SPECIFIC METAL

ROOF COVERING.

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF W/ METAL W/CRIMPED VALLEY FLASHING A-9

ZIP SYSTE TAPE*

METAL VALLEY FLASHING

ZIP SYST TAPE OR ADHESIVE

BACKED FLASHING (MUST MEET AC148)

LAPPED OVER METAL VALLEY FLASHING

METAL ROOF COVERING -

FASTEN PER CODE USING

FASTENERS COMPATIBLE

WITH SPECIFIC METAL

ROOF COVERING.

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF WITH METALWITH FLAT VALLEY FLASHING A-10

LAP LOWER PANEL OF METAL

ROOF UNDER PREFORMED METAL

ROOF VENT

METAL ROOF COVERING - FASTEN

PER CODE USING FASTENERS

COMPATIBLE WITH SPECIFIC

METAL ROOF COVERING.

UPPER METAL ROOF PANEL CUT

TO FIT AROUND PREFORMED

METAL ROOF VENT

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF WITHMETAL AT PLUMBING VENT A-11

LAP ZIP SYSTEM TAPE OR

ADHESIVE BACKED FLASHING.

(MUST MEET AC148) OVER TOP

OF CONTINUOUS FLASHING

CODE-APPROVED FLASHING

AT ROOF TO CHIMNEY

INTERSECTION

1/8-INCH GAP RECOMMENDED AT PANEL

EDGES UNLESS OTHERWISE PROVIDED

BY MACHINED PROFILED EDGES

INSTALL ZIP SYSTEM

TAPE ON ALL JOINTS OF

CHIMNEY CRICKET

METAL ROOF COVERING - FASTEN PER

CODE USING FASTENERS COMPATIBLE

WITH SPECIFIC METAL ROOF COVERING

FLASHING PER MANUFACTURER'S

INSTALLATION INSTRUCTIONS

ZIP SYSTE SHEATHING ON

WOOD-FRAMED CHIMNEY FLUE

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® SHEATHING-ROOF WITH METALINTO ZIP-WALL AT CHIMNEY A-12

ZIP SYSTEM SHEATHING ON

WOOD-FRAMED CHIMNEY

FLUE

FLASHING PER MANUFACTURER'S

INSTALLATION INSTRUCTIONS

METAL ROOF COVERING - FASTEN PER

CODE USING FASTENERS COMPATIBLE

WITH SPECIFIC METAL ROOF COVERING

07-09-2012

Telephone: 800.933.9220 - Facsimile: 704.547.9228 - www.zipsystem.comSales Office: 10925 David Taylor Drive - Suite 300 - Charlotte, NC 28262

DRAWING NOT TO SCALE

These construction details are provided to assist in the installation of ZIP System product(s) and may not apply to

every stituation. Manufacturer accepts no responsibility or liability for the use of these or other construction details.

ZIP SYSTEM® ROOF W/ METAL INTO ZIP-WALLAT CHIMNEY (ROOF EDGE) A-13