Mesh cable tray systems - OBO BETTERMANN · Quick Screwless Safe € € € OBO Bettermann's mesh...
Transcript of Mesh cable tray systems - OBO BETTERMANN · Quick Screwless Safe € € € OBO Bettermann's mesh...
QuickScrewlessSafe
OBO Bettermann's mesh cabletray systems are the ideal basis forquick, safe and economical cablerouting in all areas of professionalelectrical installations. The GR Ma-gic®, the Magic® G mesh cable trayand the C mesh cable tray withtheir various shapes, side heights,surfaces and range of accessoriesare ideal for satisfying the mostvaried cable routing requirements.The systems are well thoughtthrough and extremely efficientwhen in daily use.
Installation time is an importantfactor when it comes to choosingwhether to buy a product or not.With the GR-Magic® mesh cabletray in both the standard design oras a G mesh cable tray, OBO Bet-termann can offer a true system in-novation. Thanks to the patentedconnection system developed byOBO, the mesh cable tray can bemounted in a matter of seconds –without any connectors or tools.Just connect the two parts andyou're done. The system has there-fore redefined the concepts of rap-id mounting and flexibility.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
2
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
LogicalThe OBO mesh cable tray system
Magic® mesh cable tray
Side heightmm
FPre-gal-vanised
G Electro-galvanised
FTHot-dipgalvanised
A2Stainless steel
A4Stainless steel *
35
55
105
For fixing on brackets, suspension fittings and spacer clamps
Magic® G mesh cable tray
Side heightmm
G Electro-galvanised
FTHot-dipgalvanised
A2Stainless steel
A4Stainless steel *
50
75
125
150
For direct wall or ceiling mounting
C mesh cable tray
Side height mm
FTHot-dipgalvanised
A2Stainless steel *
50
For fixing on brackets, suspension fittings and spacer clamps
* Further combinations of surfaces and systems on request
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
3
Magic® mesh cable tray
The new GR-Magic® mesh cabletray really speeds up installationand manages this with no loss ofstability and load-bearing capacity.The moulded connectors forscrewless quick mounting ensureextremely quick installation times,even for complex mounting opera-tions. Load tests show that GR-Ma-gic® systems can fully match up totraditional screw connections.
The mesh cable trays are availablewith side heights of 35, 55 and105 mm in the electrogalvanised“Titan look” version, hot-dip gal-vanised version and in stainlesssteel. The comprehensive range ofpractical accessories, such asmesh cable tray bends, clampingpieces, quick connectors, barrierstrips, suspension profiles, brack-ets, etc., ensures that the productrange is complete down to thesmallest detail.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
4
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Compliant with standards
The electrical properties are alsofirst class: the values required bythe VDE guidelines 0639 and inthe new IEC/EN 61537 “Cablemanagement. Cable tray systemsand cable ladder systems” areachieved easily.
In addition, the system satisfies thestringent NEMA requirements forthe American market. As a result,the GR-Magic® mesh cable traycan also be used as a protectiveconductor.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
5
Function maintenance
Laying system/support system:GRM screwless straight connection, fire-tested
Safety cables:E30-E90
Tested and approved cable system with functionmaintenance according to DIN 4102 Part 12
Function maintenance with theGR-Magic®
Function maintenance with theGR-Magic®
Besides rapid mounting and thewide range of applications, theGR- Magic® offers another key be-nefit: it can be used to maintainfunction for fire safety purposes inorder to ensure supply to safety-re-lated systems for a certain periodof time in the event of a fire. TheGR Magic® has proven its stabilityin an impressive manner in firetesting according to DIN 4102 Part12.
This installation design was putthrough its paces with a cableload of 15 kg/m and a supportdistance of 1.5 m. Thanks to theGR-Magic®, a further support sys-tem is now available for whichfunction maintenance comes as-sured.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
6
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Impressive range of accessories
In addition to providing quickstraight connections, the innovat-ive GR-Magic® range of accessor-ies is also easy to handle and usethanks to its screwless connec-tions. For example, the meshcable trays can be flexibly installedon mounting rails using fasteningclips or on wall and support brack-ets using clamping lugs. Cut meshcable trays without moulded con-nectors are easy to join togetherwith a quick connector, while barri-er strips are fastened with aclamping piece and cable exitplates with clamping lugs.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
7
Magic down to the last detail
The system's effectiveness is provided by the perfectly formed meshcable tray for screwless straight connection, complemented by the widerange of well-thought-out system components. The many lockable andclamp-on elements continue the basic principle of the Magic systemdown to the last detail. Exceptional ease of use is also a priority for alladditional fastening and system components, for example when creatingbends of different radii with special corner connectors.
1
2 90° mesh cable tray bend
3 Quick connector
4 Mesh cable tray connector, long
5 Corner connector
6 Wall and central fastener
7 Mounting plate MPG
8 Wall and support bracket
9 Side holder
10 Centre suspension
11 Ceiling bracket, variable
12 Spacer clamp
13 Earthing terminal with earthing screw
14 Cable exit plate
15 Fastening element for junction boxes
16 Installation profile
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
8
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
9
As flexible as your work
Mesh cable trays cannot always be routed lengthways. Depending on theapplication, it is necessary to overcome structural obstacles or to makeunusual changes of direction, horizontally and vertically. As the OBOmesh cable trays can be cut to size as required and the system has anextensive range of accessories, it can be adapted to any structural condi-tions.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
10
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Reference
• Lieken Brot-und Backwaren GmbH• Product: mesh cable tray in various widths and side heights• Units: 2.5 km• Location of use: industrial and administrative areas
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
11
A variety of surfaces
The mesh cable trays are available in a wide varietyof surface designs that enable them to be used bothindoors and outdoors. For indoors, OBO has de-veloped the electrogalvanised surface further andmade it even more visually appealing. The result isthe new OBO “Titan look”. This provides the meshcable trays with an unmistakable, high-quality opticalappearance, which closely resembles stainless steel– making it ideal for use in false ceilings and where inview.
For use in aggressive environments as well as in thefood industry, OBO offers the GR mesh cable tray inthe stainless steel 1.4301 and 1.4401 versions. Themesh cable trays are made from quality stainlesssteel wires and pickled in a subsequent process. Thisprotects the wires against extreme chemical loads. Asthey are taste-neutral and resistant to cleaning agents,disinfectants and sterilisers, these mesh cable traysystems can also be used in the food industry.
Surface Hot galvanisation
Coating thickness Average value approx. 8-10 µm
StandardsGalvanisation toDIN EN 10244-2
Location of use Indoors
Surface Electrogalvanisation
Coating thickness Average value approx. 2.5-10 μm
Standards Electrolytic galvanisation in accord-ance withDIN EN 12329
Location of use Indoors
F
G
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
12
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
FT
Surface Hot-dip galvanisation
Coating thickness Average value approx. 40-60 µm
Standards Galvanisation according to the hot-dipmethod to DIN EN ISO 1461
Location of use Outdoors
A2
Material Stainless steel A2
Designa-tions
European material designation:1.4301American material designation:AISI 304
Specialfeatures
Welded components are also passivated; unwel-ded components are rinsed and degreased
Locationof use
Industrial areas with high levels of humidity andaggressive atmosphere, food industry, chemicaland pharmaceuticals industry
A4
Material Stainless steel A4
Designa-tions
European material designation:1.4401/1.4404/1.4571American material designation:AISI 316/316L/316Ti
Specialfeatures
Welded components are also passivated; unwel-ded components are rinsed and degreased
Locationof use
Buildings or areas with almost constant condens-ation and high levels of impurities, coastal or off-shore areas with high levels of salt
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
13
Magic® G mesh cable tray
The system for directwall and ceiling mounting
Optimum room usage
Even if space is tight, the Magic®
G mesh cable tray can be moun-ted almost anywhere. It can be at-tached directly to walls and ceil-ings in almost any position, provid-ing optimum cable routing particu-larly in false ceilings, server roomsand office buildings. This systemalso scores highly thanks to itsscrewless design.
A variety of materials
Dry rooms, wet rooms, outdoor areas, the food industry or tunnel con-struction – the GR-Magic® has the right surface for any area. The productrange runs from electrogalvanised and hot-dip galvanised right throughto stainless steel variants.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
14
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
C mesh cable tray
Maximum load-bearing capacityand versatility
The C mesh cable tray systemfrom OBO Bettermann can fulfilthe highest requirements for loadcapacities and versatility. The Cshape allows support widths of upto three metres. With a side heightof 50 mm and optimised accessor-ies such as clamping pieces, barri-er strips or installation profiles, thesystem is the perfect complementto OBO's complete mesh cabletray portfolio. It is used both in in-dustry and in all other areas ofprofessional electrical installations.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
15
Tested quality
The in-house BET Test Centre con-tinually monitors and tests thequality of OBO products. Here,OBO simulates the loads that themesh cable tray systems have towithstand on a constant basis. Wedetermine the maximum load ca-pacity and carrying capacity of the
system, as well as its resistance tocorrosion. We are able to provestandardised testing of EMC prop-erties using test reports. In otherwords, OBO places paramount im-portance on safety.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
16
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
The KTS testing system was spe-cially constructed for the testing ofOBO Bettermann cable supportsystems. Thanks to its continuousfurther development and adapta-tion to the latest requirements, it
can offer comprehensive testingoptions. For example, the tests re-quired by DIN EN 61537 can becarried out. These prove the safeworking load (SWL) and thereforethe reliable load-bearing capacity
of the systems. Tested qualitywithout compromise – made byOBO.
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
17
St Steel
G Electrogalvanised FT Hot-dip galvanised
GR-Magic® mesh cable tray
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm (exception: GRM 35/50 = 20 x 100 mm).Mesh cable tray with shaped connector of side height 35 mm.
Dimensions
3000 50 3.9 17.53000 100 3.9 353000 150 3.9 52.53000 200 3.9 703000 300 4.8 105
TypeGRM 35 50 GGRM 35 100 GGRM 35 150 GGRM 35 200 GGRM 35 300 G
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
0.25 0.11 0.10.25 0.11 0.10.25 0.11 0.10.3 0.14 0.10.75 0.22 0.15
TypeGRM 35 50 GGRM 35 100 GGRM 35 150 GGRM 35 200 GGRM 35 300 G
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
Load
Load diagram, GR-Magic® mesh cable tray, type GRM 35Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
50 3.9100 3.9150 3.9200 3.9300 4.8
TypeGRM 35 50 GGRM 35 100 GGRM 35 150 GGRM 35 200 GGRM 35 300 G
Widthmm
WireØmm Item No.
60000606000062600006360000646000066
Pack.m33333
Weightkg/100 m45.30049.00063.10076.800159.100
50 3.9100 3.9150 3.9200 3.9300 4.8
GRM 35 50 FTGRM 35 100 FTGRM 35 150 FTGRM 35 200 FTGRM 35 300 FT
60000696000071600007260000736000075
33333
45.61050.40064.50078.600162.700
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 35
18
GR-Magic® mesh cable tray
50 3.9100 3.9150 3.9200 3.9300 4.8
TypeGRM 35 50VA4301GRM 35 100VA4301GRM 35 150VA4301GRM 35 200VA4301GRM 35 300VA4301
Widthmm
WireØmm Item No.
60000546000055600005660000576000059
Pack.m33333
Weightkg/100 m45.00049.00062.60076.300157.900
50 3.9100 3.9150 3.9200 3.9300 4.8
GRM 35 50VA4401GRM 35 100VA4401GRM 35 150VA4401GRM 35 200VA4401GRM 35 300VA4401
60000866000087600008960000906000091
33333
44.62049.00062.60076.300157.900
3000 50 17.53000 100 353000 150 52.53000 200 703000 300 105
TypeGRM 35 50VA4301GRM 35 100VA4301GRM 35 150VA4301GRM 35 200VA4301GRM 35 300VA4301
Lengthmm
Dim.Bmm
Usefulcross-sectioncm²
0.25 0.11 0.10.25 0.11 0.10.25 0.11 0.10.3 0.14 0.10.75 0.22 0.15
TypeGRM 35 50VA4301GRM 35 100VA4301GRM 35 150VA4301GRM 35 200VA4301GRM 35 300VA4301
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
Load diagram, GR-Magic® mesh cable tray, type GRM 35
Dimensions
Load
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm (exception: GRM 35/50 = 20 x 100 mm).Mesh cable tray with shaped connector of side height 35 mm.
V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 35
19
Barrier strip
Barrier strip for separation of cables of different voltages or functions.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
30 0.75 3000TypeTSG 30 FS
Dim.Hmm
Plate thicknessmm
Dim.Lmm Item No.
6062050
Pack.m3
Weightkg/100 m38.000
30 0.75 3000TSG 30 DD 60623143 38.000
30 0.75 3000TSG 30 VA4301 60620523 37.670
30 0.75 3000TSG 30 VA4571 60620543 38.670
Barrier strip connector
Barrier strip connector for screwless connection of the TSG barrier strip in all side heights.
V2A Stainless steel, grade 301
TypeTSGV VA4310
Item No.6067970
Pack.pcs10
Weightkg/100 pcs.0.923
Hold-down clamp for barrier strip fastening
Hold-down clamp for fastening barrier strips in mesh cable trays.
V2A Stainless steel, grade 301
TypeKS GR VA4310
Item No.6062282
Pack.pcs30
Weightkg/100 pcs.0.830
Hold-down clamp for barrier strip fastening
38
724
Including FRS M6 x 20 bolt with flange nut.Clamp for fastening barrier strip in mesh cable trays.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGKT 38 G
Item No.6017037
Pack.pcs20
Weightkg/100 pcs.2.300
GKT 38 FT 601706120 2.400
GKT 38 VA4301 601704520 2.200
GKT 38 VA4401 601709210 2.20004
KTS
Bro
schü
re G
itter
rinne
n 20
17 /
en /
03/0
8/20
17 (L
LExp
ort_
0460
7) /
03/0
8/20
17
Side height 35
20
GR-Magic® mesh cable tray
100 3.9150 3.9200 3.9300 4.8400 4.8500 4.8600 4.8
TypeGRM 55 100 FGRM 55 150 FGRM 55 200 FGRM 55 300 FGRM 55 400 FGRM 55 500 FGRM 55 600 F
Widthmm
WireØmm Item No.
6001040600104460010476001050600105360010566001059
Pack.m3333333
Weightkg/100 m72.00085.70099.000191.100234.600276.400318.400
50 3.9100 3.9150 3.9200 3.9200 4.8300 4.8400 4.8450 4.8500 4.8600 4.8
GRM 55 50 GGRM 55 100 GGRM 55 150 GGRM 55 200 GGRM 55 200 4.8 GGRM 55 300 GGRM 55 400 GGRM 55 450 GGRM 55 500 GGRM 55 600 G
6001441600144260014446001446600144760014486001450600145160014526001454
3333333333
67.00072.40085.700100.667151.000194.900236.700238.000279.000321.200
3000 100 3.9 403000 150 3.9 633000 200 3.9 873000 300 4.8 1293000 400 4.8 1753000 500 4.8 2203000 600 4.8 265
TypeGRM 55 100 FGRM 55 150 FGRM 55 200 FGRM 55 300 FGRM 55 400 FGRM 55 500 FGRM 55 600 F
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
0.35 0.2 0.1 0.10.35 0.2 0.1 0.10.35 0.2 0.1 0.10.7 0.5 0.25 0.20.9 0.6 0.3 0.250.9 0.6 0.3 0.250.9 0.6 0.3 0.25
TypeGRM 55 100 FGRM 55 150 FGRM 55 200 FGRM 55 300 FGRM 55 400 FGRM 55 500 FGRM 55 600 F
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
2.5 mkN/m
Load diagram, GR-Magic® mesh cable tray, type GRM 55
Dimensions
Load
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm (exception: GRM 55/50 = 20 x 100 mm).Description, surface F = pre-galvanised wires according to DIN EN 10244/2 (surface approx. 10µm).Mesh cable tray with shaped connector of side height 55 mm.
St Steel
F Hot-dip galvanised G Electrogalvanised
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
21
St Steel
FT Hot-dip galvanised
GR-Magic® mesh cable tray
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm (exception: GRM 55/50 = 20 x 100 mm).Mesh cable tray with shaped connector of side height 55 mm.
Dimensions
3000 50 3.9 163000 100 3.9 403000 150 3.9 633000 200 3.9 873000 200 4.8 873000 300 4.8 1293000 400 4.8 1753000 500 4.8 2203000 600 4.8 265
TypeGRM 55 50 FTGRM 55 100 FTGRM 55 150 FTGRM 55 200 FTGRM 55 200 4.8FTGRM 55 300 FTGRM 55 400 FTGRM 55 500 FTGRM 55 600 FT
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
0.35 0.2 0.1 0.10.35 0.2 0.1 0.10.35 0.2 0.1 0.10.35 0.2 0.1 0.10.7 0.5 0.25 0.20.7 0.5 0.25 0.20.9 0.6 0.3 0.250.9 0.6 0.3 0.250.9 0.6 0.3 0.25
TypeGRM 55 50 FTGRM 55 100 FTGRM 55 150 FTGRM 55 200 FTGRM 55 200 4.8FTGRM 55 300 FTGRM 55 400 FTGRM 55 500 FTGRM 55 600 FT
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
2.5 mkN/m
Load
Load diagram, GR-Magic® mesh cable tray, type GRM 55Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
50 3.9100 3.9150 3.9200 3.9200 4.8300 4.8400 4.8500 4.8600 4.8
TypeGRM 55 50 FTGRM 55 100 FTGRM 55 150 FTGRM 55 200 FTGRM 55 200 4.8FTGRM 55 300 FTGRM 55 400 FTGRM 55 500 FTGRM 55 600 FT
Widthmm
WireØmm Item No.
600141560014166001418600142060014216001424600142860014326001436
Pack.m333333333
Weightkg/100 m66.47075.66790.000104.667154.300198.800244.300287.700331.600
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
22
GR-Magic® mesh cable tray
50 3.9100 3.9150 3.9200 3.9300 4.8400 4.8500 4.8600 4.8
TypeGRM 55 50VA4301GRM 55 100VA4301GRM 55 150VA4301GRM 55 200VA4301GRM 55 300VA4301GRM 55 400VA4301GRM 55 500VA4301GRM 55 600VA4301
Widthmm
WireØmm Item No.
60010706001072600107460010766001078600108060010826001085
Pack.m33333333
Weightkg/100 m67.00072.66688.00099.000191.100243.000287.000331.000
50 3.9100 3.9150 3.9200 3.9300 4.8400 4.8500 4.8600 4.8
GRM 55 50VA4401GRM 55 100VA4401GRM 55 150VA4401GRM 55 200VA4401GRM 55 300VA4401GRM 55 400VA4401GRM 55 500VA4401GRM 55 600VA4401
60010876001088600109060010916001093600109560010976001099
33333333
67.00072.66688.00099.000191.100243.000287.000331.000
3000 50 163000 100 403000 150 633000 200 873000 300 1293000 400 1753000 500 2203000 600 265
TypeGRM 55 50VA4301GRM 55 100VA4301GRM 55 150VA4301GRM 55 200VA4301GRM 55 300VA4301GRM 55 400VA4301GRM 55 500VA4301GRM 55 600VA4301
Lengthmm
Dim.Bmm
Usefulcross-sectioncm²
0.35 0.2 0.1 0.10.35 0.2 0.1 0.10.35 0.2 0.1 0.10.35 0.2 0.1 0.10.7 0.5 0.25 0.20.9 0.6 0.3 0.250.9 0.6 0.3 0.250.9 0.6 0.3 0.25
TypeGRM 55 50VA4301GRM 55 100VA4301GRM 55 150VA4301GRM 55 200VA4301GRM 55 300VA4301GRM 55 400VA4301GRM 55 500VA4301GRM 55 600VA4301
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
2.5 mkN/m
Load diagram, mesh cable tray GRM 55 VA
Dimensions
Load
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm (exception: GRM 55/50 = 20 x 100 mm).Mesh cable tray with shaped connector of side height 55 mm.
V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
GB Stained
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
23
St Steel
G Electrogalvanised
GR-Magic® mesh cable tray with barrier strip
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm.Mesh cable tray with shaped connector and welded barrier strips of side height 55 mm.
Dimensions
3000 100 3.9 403000 200 3.9 873000 300 4.8 1293000 400 4.8 1753000 500 4.8 220
TypeGRM-T 55 100 GGRM-T 55 200 GGRM-T 55 300 GGRM-T 55 400 GGRM-T 55 500 G
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
0.5 0.5 0.251 0.6 0.251.5 0.8 0.41.5 0.8 0.41.5 0.8 0.4
TypeGRM-T 55 100 GGRM-T 55 200 GGRM-T 55 300 GGRM-T 55 400 GGRM-T 55 500 G
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
Load
Load diagram, GR-Magic® mesh cable tray, type GRM-1T 55Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
3000 3.93000 3.93000 4.83000 4.83000 4.8
TypeGRM-T 55 100 GGRM-T 55 200 GGRM-T 55 300 GGRM-T 55 400 GGRM-T 55 500 G
Lengthmm
WireØmm Item No.
60064536006455600645660064576006458
Pack.m33333
Weightkg/100 m116.500144.100238.600280.800323.100
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
24
GR-Magic® mesh cable tray with barrier strip
3000 3.93000 4.83000 4.83000 4.8
TypeGRM-2T 55 200 GGRM-2T 55 300 GGRM-2T 55 400 GGRM-2T 55 500 G
Lengthmm
WireØmm Item No.
6006395600639660063976006468
Pack.m3333
Weightkg/100 m188.200282.700336.700367.200
3000 200 3.9 873000 300 4.8 1293000 400 4.8 1753000 500 4.8 220
TypeGRM-2T 55 200 GGRM-2T 55 300 GGRM-2T 55 400 GGRM-2T 55 500 G
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
2 1 0.42.3 1.4 0.62.3 1.4 0.61.5 0.8 0.55
TypeGRM-2T 55 200 GGRM-2T 55 300 GGRM-2T 55 400 GGRM-2T 55 500 G
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
Load diagram, GR-Magic® mesh cable tray, type GRM-2T 55
Dimensions
Load
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm.Mesh cable tray with shaped connector and two welded barrier strips of side height 55 mm.
St Steel
G Electrogalvanised
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
25
Barrier strip
Barrier strip for separation of cables of different voltages or functions.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
45 0.75 3000TypeTSG 45 FS
Dim.Hmm
Plate thicknessmm
Dim.Lmm Item No.
6062033
Pack.m3
Weightkg/100 m46.700
45 0.75 3000TSG 45 DD 60623213 46.800
45 0.75 3000TSG 45 VA4301 60620253 47.000
45 0.75 3000TSG 45 VA4571 60620283 48.000
Barrier strip connector
Barrier strip connector for screwless connection of the TSG barrier strip in all side heights.
V2A Stainless steel, grade 301
TypeTSGV VA4310
Item No.6067970
Pack.pcs10
Weightkg/100 pcs.0.923
Hold-down clamp for barrier strip fastening
Hold-down clamp for fastening barrier strips in mesh cable trays.
V2A Stainless steel, grade 301
TypeKS GR VA4310
Item No.6062282
Pack.pcs30
Weightkg/100 pcs.0.830
Hold-down clamp for barrier strip fastening
38
724
Including FRS M6 x 20 bolt with flange nut.Clamp for fastening barrier strip in mesh cable trays.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGKT 38 G
Item No.6017037
Pack.pcs20
Weightkg/100 pcs.2.300
GKT 38 FT 601706120 2.400
GKT 38 VA4301 601704520 2.200
GKT 38 VA4401 601709210 2.20004
KTS
Bro
schü
re G
itter
rinne
n 20
17 /
en /
03/0
8/20
17 (L
LExp
ort_
0460
7) /
03/0
8/20
17
Side height 55
26
90° mesh cable tray bend
90° bend, horizontal, for all mesh cable trays of 55 mm side height.
St Steel
G Electrogalvanised FT Hot-dip galvanised
100 3.9150 3.9200 3.9300 4.4400 4.8500 4.8600 4.8
TypeGRB 90 510 GGRB 90 515 GGRB 90 520 GGRB 90 530 GGRB 90 540 GGRB 90 550 GGRB 90 560 G
Widthmm
WireØmm Item No.
6001920600199860019396001947600195560019636001971
Pack.pcs1111111
Weightkg/100 pcs.7.00014.40018.40041.70065.50094.800113.300
100 3.9150 3.9200 3.9300 4.4400 4.8500 4.8600 4.8
GRB 90 510 FTGRB 90 515 FTGRB 90 520 FTGRB 90 530 FTGRB 90 540 FTGRB 90 550 FTGRB 90 560 FT
6002218600222260022266002234600224260022506002269
1111111
7.50015.10019.30043.50068.00098.400113.700
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 55
27
St Steel
G Electrogalvanised FT Hot-dip galvanised
GR-Magic® mesh cable tray
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm.Mesh cable tray with shaped connector of side height 105 mm.
Dimensions
3000 100 3.9 823000 150 3.9 1303000 200 4.8 1753000 300 4.8 2683000 400 4.8 3633000 450 4.8 4113000 500 4.8 4593000 600 4.8 554
TypeGRM 105 100 GGRM 105 150 GGRM 105 200 GGRM 105 300 GGRM 105 400 GGRM 105 450 GGRM 105 500 GGRM 105 600 G
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
0.8 0.55 0.37 0.250.8 0.55 0.37 0.251 0.7 0.4 0.251.6 0.8 0.5 0.31.6 0.8 0.5 0.31.6 0.8 0.5 0.31.6 0.8 0.5 0.31.6 0.8 0.5 0.3
TypeGRM 105 100 GGRM 105 150 GGRM 105 200 GGRM 105 300 GGRM 105 400 GGRM 105 450 GGRM 105 500 GGRM 105 600 G
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
3.0 mkN/m
Load
Load diagram, mesh cable tray, type GRM 105Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
3000 3.93000 3.93000 4.83000 4.83000 4.83000 4.83000 4.83000 4.8
TypeGRM 105 100 GGRM 105 150 GGRM 105 200 GGRM 105 300 GGRM 105 400 GGRM 105 450 GGRM 105 500 GGRM 105 600 G
Lengthmm
WireØmm Item No.
60024026002404600240660024086002410600241360024156002417
Pack.m33333333
Weightkg/100 m99.340110.600192.340236.700278.000300.000319.000363.300
3000 3.93000 3.93000 4.83000 4.83000 4.83000 4.83000 4.83000 4.8
GRM 105 100 FTGRM 105 150 FTGRM 105 200 FTGRM 105 300 FTGRM 105 400 FTGRM 105 450 FTGRM 105 500 FTGRM 105 600 FT
60024316002433600243560024376002439600244160024436002445
33333333
103.700116.000200.700244.000287.700309.700333.000375.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 105
28
GR-Magic® mesh cable tray
100 3.9150 3.9200 4.8300 4.8400 4.8500 4.8600 4.8
TypeGRM105 100VA4301GRM105 150VA4301GRM105 200VA4301GRM105 300VA4301GRM105 400VA4301GRM105 500VA4301GRM105 600VA4301
Widthmm
WireØmm Item No.
6002451600245560024576002460600246360024666002469
Pack.m3333333
Weightkg/100 m99.000111.670200.670235.000277.000319.000363.340
100 3.9150 3.9200 4.8300 4.8400 4.8500 4.8600 4.8
GRM105 100VA4401GRM105 150VA4401GRM105 200VA4401GRM105 300VA4401GRM105 400VA4401GRM105 500VA4401GRM105 600VA4401
6002475600247660024776002479600248160024836002485
3333333
99.000109.130192.340235.000277.000319.000363.340
3000 100 823000 150 1303000 200 1753000 300 2683000 400 3633000 500 4593000 600 554
TypeGRM105 100VA4301GRM105 150VA4301GRM105 200VA4301GRM105 300VA4301GRM105 400VA4301GRM105 500VA4301GRM105 600VA4301
Lengthmm
Dim.Bmm
Usefulcross-sectioncm²
0.8 0.55 0.37 0.250.8 0.55 0.37 0.250.8 0.55 0.37 0.251.1 0.75 0.53 0.31.1 0.75 0.53 0.31.25 0.85 0.6 0.31.25 0.85 0.6 0.3
TypeGRM105 100VA4301GRM105 150VA4301GRM105 200VA4301GRM105 300VA4301GRM105 400VA4301GRM105 500VA4301GRM105 600VA4301
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
3.0 mkN/m
Load diagram, mesh cable tray, type GRM 105
Dimensions
Load
No additional connection components are required for the mesh cable tray, it is simply interlocked.The grid width is 50 x 100 mm.Mesh cable tray with shaped connector of side height 105 mm.
V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
GB Stained
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 105
29
Barrier strip
Barrier strip for separation of cables of different voltages or functions.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
85 0.75 3000TypeTSG 85 FS
Dim.Hmm
Plate thicknessmm
Dim.Lmm Item No.
6062114
Pack.m3
Weightkg/100 m70.300
85 0.75 3000TSG 85 DD 60623313 70.300
85 0.75 3000TSG 85 VA4301 60621733 69.670
Barrier strip connector
Barrier strip connector for screwless connection of the TSG barrier strip in all side heights.
V2A Stainless steel, grade 301
TypeTSGV VA4310
Item No.6067970
Pack.pcs10
Weightkg/100 pcs.0.923
Hold-down clamp for barrier strip fastening
Hold-down clamp for fastening barrier strips in mesh cable trays.
V2A Stainless steel, grade 301
TypeKS GR VA4310
Item No.6062282
Pack.pcs30
Weightkg/100 pcs.0.830
Hold-down clamp for barrier strip fastening
38
724
Including FRS M6 x 20 bolt with flange nut.Clamp for fastening barrier strip in mesh cable trays.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGKT 38 G
Item No.6017037
Pack.pcs20
Weightkg/100 pcs.2.300
GKT 38 FT 601706120 2.400
GKT 38 VA4301 601704520 2.200
GKT 38 VA4401 601709210 2.20004
KTS
Bro
schü
re G
itter
rinne
n 20
17 /
en /
03/0
8/20
17 (L
LExp
ort_
0460
7) /
03/0
8/20
17
Side height 105
30
90° mesh cable tray bend
90° bend, horizontal, for all mesh cable trays of 105 mm side height.
St Steel
G Electrogalvanised FT Hot-dip galvanised
100 3.9150 3.9200 4.4300 4.8400 4.8450 4.8500 4.8600 4.8
TypeGRB 90 110 GGRB 90 115 GGRB 90 120 GGRB 90 130 GGRB 90 140 GGRB 90 145 GGRB 90 150 GGRB 90 160 G
Widthmm
WireØmm Item No.
60023706002372600237460023766002378600238060023826002384
Pack.pcs11111111
Weightkg/100 pcs.9.50018.00030.40061.00077.000100.000114.000134.000
100 3.9150 3.9200 4.4300 4.8400 4.8450 4.8500 4.8600 4.8
GRB 90 110 FTGRB 90 115 FTGRB 90 120 FTGRB 90 130 FTGRB 90 140 FTGRB 90 145 FTGRB 90 150 FTGRB 90 160 FT
60023076002311600231560023236002331600233560023586002366
11111111
10.00019.00036.00062.00081.900102.000113.000133.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 105
31
Joint connector
34
28
Including FRS M6 x 20 bolt with flange nut.Screwed version of joint connector for mesh cable trays.Figure: Positioning and quantity of mesh cable tray connectors.50-150 mm = 2 units200-300 mm = 3 units400-450 mm = 4 units500-600 mm = 5 units
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGSV 34 G
Item No.6016596
Pack.pcs20
Weightkg/100 pcs.3.000
GSV 34 FT 601663420 3.000
GSV 34 VA4301 601664220 3.000
GSV 34 VA4401 601664820 3.000
Quick connector
When selecting the connector, please take the appropriate wire thickness of the mesh cable trayinto account.Quick connector for screwless straight connection of mesh cable trays without special tools, formesh cable trays up to a width of 150 mm.Figure: Positioning and quantity of mesh cable tray connectors.50-150 mm = 2 units
St Steel
DD Strip galvanised zinc/aluminium, Double Dip
TypeGRS 3.9 DDGRS 4.8 DD
Item No.60165456016561
Pack.pcs5050
Weightkg/100 pcs.2.5002.500
Mesh cable tray connector, long
Two straight connectors, type GRV 245, are used for each connection point.Can be used from a mesh cable tray width of 100 mm.Long mesh cable tray connectors for screwless straight connection of mesh cable trays.
St Steel V4A Stainless steel, grade 316 L
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
245TypeGRV 245 FS
Widthmm Item No.
6016680
Pack.pcs20
Weightkg/100 pcs.13.500
245GRV 245 DD 601668420 13.500
245GRV 245 VA4404 601668820 13.500
Side connector
Including screw of type FRS M6 x 20.Screwed version of joint connector for mesh cable trays.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeK 11 262 FT
Item No.6015107
Pack.pcs25
Weightkg/100 pcs.7.500
K 11 262 VA4301 601636725 7.500
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
32
Corner connector
23
42--54
Including FRS M6 x 12 bolt with flange nutCorner connector for the creation of mesh cable tray bend elements.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGEV 36 G
Item No.6016715
Pack.pcs20
Weightkg/100 pcs.3.000
GEV 36 FT 601672320 3.000
GEV 36 VA4301 601673120 3.000
GEV 36 VA4401 601676410 3.000
Slotted steel strap
d
b
t
5 5e
Perforated slotted steel strap in strips.
St Steel
FT Hot-dip galvanised
20 x 3 6,5 x 40 27020 x 3 6,5 x 40 1000
Type5050 20X3 FT5050 20X3 1M FT
Dimensionmm
Holesizemm
Lengthmm Item No.
14665001466504
Pack.pcs2020
Weightkg/100 pcs.9.45035.000
Slotted steel strap, bent
Set includes four clamps, type GKS 34.Bent slotted steel strap for creation of bends and tees.
St Steel
FT Hot-dip galvanised
20x3Type5050 20X3 FT
Dimensionmm Item No.
6017371
Pack.pcs25
Weightkg/100 pcs.15.800
Hold-down clamp
34
22
Including FRS M6 x 20 bolt with flange nut.Clamp for fixing mesh cable trays to wall or support brackets.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
TypeGKS 34 G
Item No.6016855
Pack.pcs20
Weightkg/100 pcs.2.000
GKS 34 FT 601682020 2.000
GKS 34 VA4301 601683920 2.000
GKS 34 VA4401 601685910 2.000
Hold-down clamp
Clamp for fastening mesh cable trays of width 50 mm to the floor.
St Steel V2A Stainless steel, grade 304
G Electrogalvanised
TypeGKB 34 G
Item No.6016674
Pack.pcs20
Weightkg/100 pcs.1.000
GKB 34 VA4301 601667620 1.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
33
Hold-down clamp
38
724Hold-down clamp for floor fastening of mesh cable trays.
St Steel V2A Stainless steel, grade 304
G Electrogalvanised
TypeGKB 38 G
Item No.6017020
Pack.pcs20
Weightkg/100 pcs.1.200
GKB 38 VA4301 601701820 1.200
Hold-down clamp
Clamp for fastening mesh cable trays.
St Steel V4A Stainless steel, grade 316 L
FS Strip-galvanised FT Hot-dip galvanised
711
TypeGKS 50 07 FSGKS 50 11 FS
HoleØmm Item No.
60152636015276
Pack.pcs5050
Weightkg/100 pcs.4.0004.000
711
GKS 50 07 FTGKS 50 11 FT
60152716015278
5050
4.1004.100
711
GKS 50 07 V4AGKS 50 11 V4A
60153106015280
5020
4.0004.000
Earthing clip
• For cables to 16 mm² and flat conductors• Fit: cable to 16 mm² x max. FL 30• With riveted brass connection terminal and one cylinder bolt, M5 x 12, with two cylinder bolts, M6x 16
St Steel
G Electrogalvanised
150Type939
Shippingboxpcs Item No.
5043107
Pack.pcs25
Weightkg/100 pcs.5.932
Connection and earthing terminal
10
48M6
25 The connection and earthing terminal is used to reduce electrical resistance and therefore im-proves the electric conductivity in mesh cable systems in the area of the joint allowing to fulfil thehigh demands in terms of the transition resistance according to e.g. NEMA and CSA. Further-more, the connection and earthing terminal is compulsory when used as a protective conductor ina mesh cable tray system (Note: National regulations have to be followed when creating such asystem).
St Steel
FS Strip-galvanised
TypeVEK-GRM 3.9 FSVEK-GRM 4.8 FS
Item No.60166946016696
Pack.pcs2525
Weightkg/100 pcs.3.8503.800
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
34
Earthing screw
Earthing terminal for fastening the equipotential bonding wire to the cable support system.
CuZn Brass
22 8 25 18 M6 —26 10 35 21 M6 —
TypeEKL 25 M6EKL 35 M6
Dim.Lmm
Dim.lmm
Cross–sectionmm²
SWmm Thread Accessories Item No.
64040066404014
Pack.pcs5050
Weightkg/100 pcs.3.1004.800
Side holder for cable gland
Conduit take off bracket with perforation for accepting cable glands.
St Steel
FS Strip-galvanised
20TypeSH KAB 20 FS
HoleØmm Item No.
6015425
Pack.pcs10
Weightkg/100 pcs.15.000
25SH KAB 25 FS 601543310 14.700
Drop-out plate
The drop-out plate allows compliance with specific bend radii (fibre-optic cables), thus preventingpossible cable breaks. Can be mounted in a lengthwise direction and at the side, can be arrangedfor greater widths.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised FT Hot-dip galvanised
TypeKAB GR FS
Item No.6220139
Pack.pcs10
Weightkg/100 pcs.14.100
KAB GR FT 622014210 14.100
KAB GR VA 1.4301 622014510 14.100
Mounting plate
Mounting plate, for fastening on the side rail of cable support systems.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
115 170TypeMP UNI FS
Heightmm
Widthmm Item No.
7084773
Pack.pcs40
Weightkg/100 pcs.13.300
115 170MP UNI DD 708511440 11.000
115 170MP UNI VA4301 708513340 11.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
35
Fastening element for mesh cable tray
The fastening element BE TS GR can be used to attach OBO junction boxes, type T60 and T100,to all standard mesh cable trays in a few actions, quickly and without tools. This is all done withoutusing tools.This keeps the junction box securely in position. However, it can be quickly dismantled as neces-sary.
PC Polycarbonate
TypeBE TS GR
Item No.2007833
Pack.pcs10
Weightkg/100 pcs.2.300
Identification clip
Pastel orange
Zinc yellow
Light blue
Signal green
0.920 0.742 0.920 0.92010 10 10 10
Colour
Weight kg/100 pcs.Pack. pcs
Type KS GR OR KS GR ZGB KS GR LBL KS GR SGN
Item No. 6017712 6017713 6017714 6017715
The identification clip is fastened to the mesh cable tray without screws simply by attaching it.
PA Polyamide
Bolt cutter
Bolt cutter for cutting mesh cable trays.
St Steel
450TypeGR BS
Lengthmm Item No.
6017700
Pack.pcs1
Weightkg/100 pcs.160.000
End cap
15 End cap to cover cut wire ends of mesh cable trays.
PVC Polyvinylchloride
Pure orangePure orange
TypeGR KS 3.9 ORGR KS 4.8 OR
ColourItem No.60037506003754
Pack.pcs500500
Weightkg/100 pcs.0.0250.030
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
36
Cover, unperforated
B+4
1330
00
Transverse bead from 500 mm width.Cover for cable trays and mesh cable trays.When using covers outdoors, additional measures against the influence of wind must be taken.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
50 0.75 3000100 0.75 3000150 0.75 3000200 1.00 3000300 1.00 3000400 1.00 3000500 1.25 3000600 1.25 3000
TypeDRLU 050 FSDRLU 100 FSDRLU 150 FSDRLU 200 FSDRLU 300 FSDRLU 400 FSDRLU 500 FSDRLU 600 FS
Widthmm
Plate thicknessmm
Lengthmm Item No.
60520566052103605215360522106052307605240560525126052609
Pack.m33333333
Weightkg/100 m44.70098.670138.000177.670255.670334.670619.500737.340
50 0.75 3000100 0.75 3000150 0.75 3000200 1.00 3000300 1.00 3000400 1.00 3000500 1.25 3000600 1.25 3000
DRLU 050 DDDRLU 100 DDDRLU 150 DDDRLU 200 DDDRLU 300 DDDRLU 400 DDDRLU 500 DDDRLU 600 DD
60526406052643605264760526506052656605266260526686052674
33333333
59.67089.000138.340177.670256.000334.470619.340737.270
50 1.00 3000100 1.00 3000150 1.00 3000200 1.00 3000300 1.00 3000400 1.00 3000500 1.25 3000600 1.25 3000
DRLU 050 VA4301DRLU 100 VA4301DRLU 150 VA4301DRLU 200 VA4301DRLU 300 VA4301DRLU 400 VA4301DRLU 500 VA4301DRLU 600 VA4301
60528216052824605282860528316052834605283760528416052844
33333333
59.67099.000138.000177.670256.000334.670516.000737.270
50 1.00 3000100 1.00 3000150 1.00 3000200 1.00 3000300 1.00 3000400 1.00 3000500 1.25 3000600 1.25 3000
DRLU 050 VA4571DRLU 100 VA4571DRLU 150 VA4571DRLU 200 VA4571DRLU 300 VA4571DRLU 400 VA4571DRLU 500 VA4571DRLU 600 VA4571
60529786052991605299260529936052994605299560529966052998
33333333
59.67099.000138.000177.670256.000334.670619.500737.270
Cover clamp, universal
14.5
1020
4733
4
Depending on the tray width, 4–6 cover clamps are required for secure fastening of a 3 m cover.Cover clamp for universal fastening of covers on cable trays, mesh cable trays and AZ channels.The cover clamp is not suitable for use with mesh cable trays with a side height of 35 mm.
V2A Stainless steel, grade 301
TypeDKU VA4310
Item No.6065600
Pack.pcs20
Weightkg/100 pcs.0.800
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Accessories for side height 35, 55, 105 mm
37
Wall mounting for type GRM 35x50
39
20
8,5
30
16
Wall mounting for wall fastening of mesh cable trays, type GRM 35x50
St Steel V4A Stainless steel, grade 316
FT Hot-dip galvanised
35 50TypeWH GRM35 FT
Side heightmm
Widthmm Item No.
6016443
Pack.pcs10
Weightkg/100 pcs.1.950
35 50WH GRM35 VA4401 601644510 1.950
Wall clamp/central hanger
Recommendation:As wall mounting up to max. mesh cable tray width 200 mm.As centre suspension up to max. mesh cable tray width 200 mm.
As a trapeze suspension from a width of 300 mm.Wall clamp and central hanger for mesh cable trays.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised
TypeK 12 1818 FS
Item No.6437109
Pack.pcs25
Weightkg/100 pcs.7.600
K12 1818 VA4301 601642125 7.600
Mounting plate
Mounting plate for screwless wall fastening of mesh cable trays.
St Steel V4A Stainless steel, grade 316 L
FT Hot-dip galvanised
81 65 45 15111 95 45 38
TypeMPG 65 FTMPG 90 FT
Dim.Amm
Dim.Bmm
Dimen-sion xmm
Dimen-sion ymm Item No.
60064866006487
Pack.pcs3030
Weightkg/100 pcs.9.20016.800
81 65 45 15111 95 45 38
MPG 65 VA4404MPG 90 VA4404
60064886006489
3030
8.80016.100
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
38
TP support / wall and support bracket
100 1.5150 1200 0.9300 0.55
TypeTPSAG 145 FSTPSAG 195 FSTPSAG 245 FSTPSAG 345 FS
Forwidthmm
F in kNkN Item No.
6366015636602363660316366066
Pack.pcs50202020
Weightkg/100 pcs.33.00041.00048.00061.000
100 1.5150 1200 0.9300 0.55
TPSAG 145 FTTPSAG 195 FTTPSAG 245 FTTPSAG 345 FT
6366131636613563661396366143
50202020
33.00042.00049.00065.000
100 1.5150 1200 0.9300 0.55
TPSAG 145 VA4301TPSAG 195 VA4301TPSAG 245 VA4301TPSAG 345 VA4301
6366145636614663661486366149
50202020
32.00040.00047.00061.000
145 50195 100245 150345 250
TypeTPSAG 145 FSTPSAG 195 FSTPSAG 245 FSTPSAG 345 FS
Dim.Bmm
Dim.Lmm
Load diagram, bracket TPSAG
Dimensions
Load
Max. total load F = cable weight + cable tray + bracket. The load capacity values increase consid-erably when used in uncracked concrete. The values given are based on concrete of strengthclass C20/25. Observe the installation conditions of the DIBt approval (anchors).
Wall fastening
Anchor typeBZ-U 8-30-41/95
BZ-U 10-30-50/110
Max. load F [kN]Bracket width [mm]
145 195 245 345
1,00 0,80 0,70 0,50
1,50 1,00 0,90 0,55
Characteristic anchor load values for TP bracket
If the bracket is fastened directly to the wall or the profiles are screwed together, then, for reasonsof stability, always use the spacer, type DS 4.TP bracket with clamping lugs for screwless mesh cable tray fastening.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised FT Hot-dip galvanised
Bending of the bracket tip at permitted bracket load
Permitted bracket load in kN without man load
Load curve with bracket lengths in mm
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
39
St Steel
FS Strip-galvanised
Wall and support bracket MWAG 12
Including truss-head bolt M10 x 25 for fastening toU supports.Light-duty wall and support bracket for screwless mesh cable tray fastening.
Dimensions
110 32.5 53 11210 32.5 65 11310 38 75 11410 38 83 11
TypeMWAG 12 11 FSMWAG 12 21 FSMWAG 12 31 FSMWAG 12 41 FS
Dim.Bmm
Dim.Amm
Dim.Hmm
HoleØmm
Load
Load diagram, bracket type MWAG 12Bending of the bracket tip at permitted bracket load
Permitted bracket load in kN without man load
Load curve with bracket lengths in mm
Max. total load F = cable weight + cable tray + bracket. The load capacity values increase consid-erably when used in uncracked concrete. The values given are based on concrete of strengthclass C20/25. Observe the installation conditions of the DIBt approval (anchors).
Wall fastening
Anchor typeBZ-U 8-10-21/75
BZ-U 10-10-30/90
Max. load F [kN]Bracket width [mm]
110 210 310 410
1,20 0,95 0,70 0,65
1,20 1,20 1,20 1,20
Characteristic anchor load values for wall and support bracket MWAG 12
Load values for MWAG 12 on suspended support
Max. total load F in kN
SupportUS 3 K/ 20 - 60
US 3 K/ 70 - 120US 5 K/ 20 - 60US 5 K/ 70 - 120
Bracket length in mm100 200 300 400
1,20 1,20 1,20 1,201,20 1,20 1,20 1,201,20 1,20 1,20 1,201,20 1,20 1,20 1,20
110 1.2210 1.2310 1.2410 1.2
TypeMWAG 12 11 FSMWAG 12 21 FSMWAG 12 31 FSMWAG 12 41 FS
Widthmm
F in kNkN Item No.
6424600642460864246166424624
Pack.pcs30303025
Weightkg/100 pcs.12.70024.40050.30068.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
40
Wall and support bracket AWG 15
110 1.5160 1.5210 1.5310 1.5410 1.5510 1.5610 1.5
TypeAW G 15 11 FTAW G 15 16 FTAW G 15 21 FTAW G 15 31 FTAW G 15 41 FTAW G 15 51 FTAW G 15 61 FT
Widthmm
F in kNkN Item No.
6420606642060764206086420610642061264206146420616
Pack.pcs30303030302020
Weightkg/100 pcs.14.00020.00026.00035.00056.00069.00084.000
110 1.5210 1.5310 1.5410 1.5510 1.5610 1.5
AWG 15 11 VA4301AWG 15 21 VA4301AWG 15 31 VA4301AWG 15 41 VA4301AWG 15 51 VA4301AWG 15 61 VA4301
642062564206286420631642063464206376420640
303030302020
13.00025.00033.00053.00065.00080.000
110 1.5210 1.5310 1.5410 1.5510 1.5610 1.5
AWG 15 11 VA4571AWG 15 21 VA4571AWG 15 31 VA4571AWG 15 41 VA4571AWG 15 51 VA4571AWG 15 61 VA4571
642064264206446420646642064864206506420652
303030302020
13.00025.00033.00053.00065.00080.000
110 40 50 11160 40 55 11210 40 60 11310 40 65 11410 40 70 11510 40 75 11610 40 80 11
TypeAW G 15 11 FTAW G 15 16 FTAW G 15 21 FTAW G 15 31 FTAW G 15 41 FTAW G 15 51 FTAW G 15 61 FT
Dim.Bmm
Dim.Amm
Dim.Hmm
HoleØmm
Load diagram, bracket type AW G 15
Dimensions
Load
Max. total load F = cable weight + cable tray + bracket. The load capacity values increase consid-erably when used in uncracked concrete. The values given are based on concrete of strengthclass C20/25. Observe the installation conditions of the DIBt approval (anchors).
Wall fastening
Anchor typeBZ-U 8-10-21/75
BZ-U 10-10-30/90
Max. load F [kN]Bracket width [mm]
110 160 210 310 410 510 560 610
1,10 0,90 0,80 0,65 0,55 0,50 0,45 0,45
1,50 1,50 1,40 1,10 0,95 0,85 0,80 0,80
Characteristic anchor load values for wall and support bracket AW G 15
Max. total load F in kN
SupportUS 3 K/ 20 - 60
US 3 K/ 70 - 120US 5 K/ 20 - 60US 5 K/ 70 - 120
Bracket length in mm100 200 300 400
1,50 1,50 1,30 1,301,50 1,50 1,30 1,301,50 1,50 1,50 1,501,50 1,50 1,40 1,50
Fastening of the bracket to the U support of width 400 mm or greater using hexagonal bolt throughboth sides of the support. Please insert suitable spacers.Light-duty wall and support bracket with welded head plate for screwless mesh cable tray fasten-ing.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
GB Stained FT Hot-dip galvanised
Bending of the bracket tip at permitted bracket load
Permitted bracket load in kN without man load
Load curve with bracket lengths in mm
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
41
Threaded rod
Threaded rod to DIN 976.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
G Electrogalvanised
M6 6 1000M8 8 1000M10 10 1000M12 12 1000
Type2078 M6 1M G2078 M8 1M G2078 M10 1M G2078 M12 1M G
Thread
Dim.dmm
Dim.Lmm Item No.
3141047314112831412093141306
Pack.pcs10101010
Weightkg/100 pcs.18.30030.00049.00062.000
M6 6 2000M8 8 2000M10 10 2000M12 12 2000
2078 M6 2M G2078 M8 2M G2078 M10 2M G2078 M12 2M G
3141048314113631411403141144
10101010
36.60060.00098.000140.000
M6 6 1000M8 8 1000M10 10 1000M12 12 1000
2078 M6 1M V2A2078 M8 1M V2A2078 M10 1M V2A2078 M12 1M V2A
3141327314131031413123141314
10101010
18.30030.00049.00070.000
M6 6 2000M8 8 2000M10 10 2000M12 12 2000
2078 M6 2M V2A2078 M8 2M V2A2078 M10 2M V2A2078 M12 2M V2A
3141328314133031413393141316
10101010
36.60060.00098.000140.000
M6 6 1000M8 8 1000M10 10 1000M12 12 1000
2078 M6 1M V4A2078 M8 1M V4A2078 M10 1M V4A2078 M12 1M V4A
3141482314149231415023141512
50502520
18.30030.00049.00070.000
M6 6 2000M8 8 2000M10 10 2000M12 12 2000
2078 M6 2M V4A2078 M8 2M V4A2078 M10 2M V4A2078 M12 2M V4A
3141484314149431415043141514
25252010
36.60060.00098.000140.000
Side holder
Side holder for suspension of mesh cable trays.
St Steel V4A Stainless steel, grade 316
FS Strip-galvanised FT Hot-dip galvanised
M10TypeSH M10 FS
Forthreadedrod Item No.
6015336
Pack.pcs50
Weightkg/100 pcs.5.800
M10SH M10 FT 601533850 6.000
M10SH M10 A4 601534020 5.500
Side holder, universal
Side holder to fasten cable trays, mesh cable trays and cable ladders to ceilings using a threadedrod.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316 Ti
FS Strip-galvanised DD Strip galvanised zinc/aluminium, Double Dip
TypeSHU M12 FS
Item No.6015322
Pack.pcs50
Weightkg/100 pcs.5.100
SHU M12 DD 601532450 5.100
SHU M12 VA4301 601532650 5.100
SHU M12 VA4571 601532850 5.100
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
42
Centre suspension
Ø
65
40
When filling with cables, please ensure an even distribution. The maximum recommended meshcable tray width is 200 mm.Two-part centre suspension of mesh cable trays.
St Steel V4A Stainless steel, grade 316
FS Strip-galvanised FT Hot-dip galvanised
7911
TypeGMA M6 FSGMA M8 FSGMA M10 FS
HoleØmm Item No.
601522060152396015247
Pack.pcs252525
Weightkg/100 pcs.8.0008.3008.300
7911
GMA M6 FTGMA M8 FTGMA M10 FT
601522460152436015255
252525
8.4008.3008.400
7911
GMA M6 VA4401GMA M8 VA4401GMA M10 VA4401
601522860152456015261
252525
8.4008.3008.300
Centre suspension
Centre suspension including hold-down clamp for mesh cable tray suspensions.
St Steel V4A Stainless steel, grade 316 L
FS Strip-galvanised
170270370470570
TypeGMS 170 FSGMS 270 FSGMS 370 FSGMS 470 FSGMS 570 FS
Dim.Bmm Item No.
60154006015402601540460154066015408
Pack.pcs2525251010
Weightkg/100 pcs.20.00032.00043.00055.00067.000
170270370470570
GMS 170 VA4404GMS 270 VA4404GMS 370 VA4404GMS 470 VA4404GMS 570 VA4404
60154186015419601542060154216015422
2525251010
20.00032.00043.00055.00067.000
Hold-down clip
Hold-down clip for the screwless mounting of mesh cable trays onto MS profile rails.
V2A Stainless steel, grade 301
17 For wire thicknesses 3.9 and 4.8 mmTypeBC GR 4.8 VA
Dim.bmm Version Item No.
6016665
Pack.pcs20
Weightkg/100 pcs.1.760
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
43
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised FT Hot-dip galvanised
TP wall and ceiling bracket
Important! If the ceiling bracket is fastened directly to the wall or ceiling, then, for reasons of stabil-ity, always use the spacer, type DS 4.Max. side height of the cable support system 60 mm.TP wall and ceiling bracket with clamping lugs for screwless mesh cable tray fastening.
Dimensions
145 110195 160245 210345 310
TypeTPDG 145 FSTPDG 195 FSTPDG 245 FSTPDG 345 FS
Dim.Bmm
Dim.Lmm
Load
Load diagram, ceiling bracket TPDGBending of the bracket tip at permitted bracket load
Permitted bracket load in kN without man load
Load curve with bracket lengths in mm
Max. total load F = cable weight + cable tray + ceiling bracket. The load capacity values increaseconsiderably when used in uncracked concrete. The values given are based on concrete ofstrength class C20/25.
Wall fastening
Anchor typeBZ-U 8-30-41/95
BZ-U 10-30-50/110
Max. load F [kN]Bracket length [mm]
145 245 345 445 545
1,00 0,70 0,50 0,40 0,30
1,50 0,90 0,55 0,45 0,35
Ceiling fastening
Anchor typeBZ-U 8-30-41/95
BZ-U 10-30-50/110
Max. load F [kN]Bracket width [mm]
145 245 345 445 545
1,30 0,80 0,50 0,35 0,25
1,30 0,80 0,50 0,35 0,25
Characteristic anchor load values for TPDG wall and ceiling bracket
100 1.3 1.4150 0.95 1.05200 0.8 0.87300 0.5 0.55
TypeTPDG 145 FSTPDG 195 FSTPDG 245 FSTPDG 345 FS
Forwidthmm
F in kN ceilingkN
F in kN WallkN Item No.
6365906636591463659226365949
Pack.pcs6655
Weightkg/100 pcs.53.00091.10068.00081.000
100 1.3 1.4200 0.8 0.87300 0.5 0.55
TPDG 145 FTTPDG 245 FTTPDG 345 FT
636597763659816365985
655
56.00071.00086.000
100 1.3 1.4150 0.95 1.05200 0.8 0.87300 0.5 0.55
TPDG 145 VA4301TPDG 195 VA4301TPDG 245 VA4301TPDG 345 VA4301
6365989636599163659936365995
6655
53.00091.10067.00081.000
TP profile
TP profile with clamping lugs.
St Steel
FS Strip-galvanised FT Hot-dip galvanised
3000TypeTPSG 3000 FS
Lengthmm Item No.
6366090
Pack.pcs1
Weightkg/100 pcs.401.700
3000TPSG 3000 FT 63660931 461.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
44
End cap
19
23.6
End cap to cover ends of TP supports.
PE Polyethylene
Pastel orangeTypeTPS KS OR
ColourItem No.6364625
Pack.pcs10
Weightkg/100 pcs.0.569
Spacer
For static reasons, the spacer is always used to prevent the profile from deforming when thefastening bolts are tightened.Spacer for use in profiles, type TP.
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised FT Hot-dip galvanised
TypeDS 4 FS
Item No.6416551
Pack.pcs20
Weightkg/100 pcs.3.700
DS 4 FT 641658620 3.800
DS 4 VA4301 641659410 3.700
Truss-head bolt
Truss-head bolt with square neck. With washer and hexagonal nut.
St Steel V2A Stainless steel, A2
F Hot-dip galvanised
M 10 x 25TypeFRS 10x25 TPS F
Dimensionmm Item No.
6407536
Pack.pcs50
Weightkg/100 pcs.4.300
M 10 x 25FRS 10x25 TPS A2 640753750 4.000
Hexagonal bolt
Hexagonal bolt for universal fixing of structure components.
St Steel
F Hot-dip galvanised
M 10 x 60 60 10 17TypeSKS 10x60 F
Dimensionmm
Dim.Lmm
Dim.dmm
SWmm Item No.
6408516
Pack.pcs20
Weightkg/100 pcs.6.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
45
Stand-off bracket
B+70
B+6
20
35
9x 15
30
Screwless fastening of the mesh cable tray on the stand-off bracket.Stand-off bracket for stand-off of mesh cable trays on the floor or on the wall.
St Steel
FS Strip-galvanised FT Hot-dip galvanised
50100150200300400500600
TypeDBLG 20 050 FSDBLG 20 100 FSDBLG 20 150 FSDBLG 20 200 FSDBLG 20 300 FSDBLG 20 400 FSDBLG 20 500 FSDBLG 20 600 FS
Dim.Bmm Item No.
60156466015654601565860156626015670601568960156936015697
Pack.pcs2020202020202525
Weightkg/100 pcs.10.30013.80017.40020.90037.30046.70056.90066.400
50100150200300400500600
DBLG 20 050 FTDBLG 20 100 FTDBLG 20 150 FTDBLG 20 200 FTDBLG 20 300 FTDBLG 20 400 FTDBLG 20 500 FTDBLG 20 600 FT
60156486015656601566060156646015672601569160156956015699
2020202020202525
10.70014.30018.10021.70038.80048.60059.20069.100
Tray fastening system set 10 kg with TrayFix large
• Mounting system for the fastening of mesh cable trays and cable trays on FangFix stone e.g.cable routing on a flat roof.• Adapted to OBO cable tray systems MKSM, SKSM and IKSM• Adapted to OBO mesh cable tray systems with a minimum width of 100 mm• Set consisting of TrayFix mounting adapter and concrete block including base for FangFix-Sys-tem 10 kg
100TypeTrayFix-10-L
From tray widthmm Item No.
5403101
Pack.pcs1
Weightkg/100 pcs.1,100.000
Tray fastening system set 10 kg with TrayFix small
• Mounting system for the fastening of mesh cable trays and cable trays on FangFix stone e.g.cable routing on a flat roof.• Adapted to OBO mesh cable systems with a minimum width of 100 mm• Set consisting of clamping piece, fastening plug and concrete block including base for FangFix-System 10 kg
100TypeTrayFix-10-S
From tray widthmm Item No.
5403102
Pack.pcs1
Weightkg/100 pcs.1,000.000
Tray fastening system set 16 kg with TrayFix large
• Mounting system for the fastening of mesh cable trays and cable trays on FangFix stone e.g.cable routing on a flat roof.• Adapted to OBO cable tray systems MKSM, SKSM and IKSM• Adapted to OBO mesh cable tray systems with a minimum width of 100 mm• Set consisting of TrayFix mounting adapter and concrete block including base for FangFix-Sys-tem 16 kg
100TypeTrayFix-16-L
From tray widthmm Item No.
5403098
Pack.pcs1
Weightkg/100 pcs.1,700.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
46
Tray fastening system set 16 kg with TrayFix small
• Mounting system for the fastening of mesh cable trays and cable trays on FangFix stone e.g.cable routing on a flat roof.• Adapted to OBO mesh cable systems with a minimum width of 100 mm• Set consisting of clamping piece, fastening plug and concrete block including base for FangFix-System 16 kg
100TypeTrayFix-16-S
From tray widthmm Item No.
5403099
Pack.pcs1
Weightkg/100 pcs.1,700.000
Mesh angle
30
80
30
100
40
Mesh angle for routing cables in steel girders.
St Steel
FT Hot-dip galvanised
2000 4.4TypeGW 40 80 FT
Lengthmm
WireØmm Item No.
6003818
Pack.m50
Weightkg/100 m63.000
Beam clamp
When selecting the beam clamp, please take the flange thickness of the steel girder into account.Beam clamp for fastening the mesh angle, type GW 40/80 to steel girders.
St Steel
FT Hot-dip galvanised
2030
TypeKL 20 FTKL 30 FT
Heightmm Item No.
60038506003869
Pack.pcs1010
Weightkg/100 pcs.22.00024.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Mounting systems
47
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
G mesh cable tray Magic, side height 50 mm
G-shaped mesh cable tray made of spot-welded steel wire with different side heights and widths. Direct wall or ceiling mounting possible. Load capacity details regarding the different mountingmethods are available upon request.
Dimensions
3000 55 55 33 40 3.9TypeG-GRM 50 50 G
Lengthmm
Dim.Bmm
Dim.Hmm
Dim.Cmm
Dim.Amm
WireØmm
Load
Support spacing [m] Load [kN/m] Fastening variant 1 1.5 2 2.5Wall fastening K12 1818 0.2 0.15 0.1 0.05Ceiling fastening K12 1818 0.25 0.2 0.10 0.05
G-GRM 50/50
50 3.9TypeG-GRM 50 50 G
Side heightmm
WireØmm Item No.
6005535
Pack.m3
Weightkg/100 m67.100
50 3.9G-GRM 50 50 FT 60055203 68.600
50 3.9G-GRM 50 50V2A 60055503 67.100
50 3.9G-GRM 50 50V4A 60055653 67.100
Hook rail for G mesh cable tray
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised
50 25 15TypeG-GRM-R50 FS
Lengthmm
Widthmm
Side heightmm Item No.
6005605
Pack.pcs25
Weightkg/100 pcs.2.300
50 25 15G-GRM-R50VA4301 600563525 2.300
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
G mesh cable tray Magic
48
G mesh cable tray Magic, side height 75 mm
75 3.9TypeG-GRM 75 50 G
Side heightmm
WireØmm Item No.
6005538
Pack.m3
Weightkg/100 m79.900
75 3.9G-GRM 75 50 FT 60055233 81.700
75 3.9G-GRM 75 50V2A 60055533 79.900
75 3.9G-GRM 75 50V4A 60055683 79.900
3000 53 73 40 53 3.9TypeG-GRM 75 50 G
Lengthmm
Dim.Bmm
Dim.Hmm
Dim.Cmm
Dim.Amm
WireØmm
Support spacing [m] Load [kN/m] Fastening variant 1 1.5 2 2.5Bracket MWAG 12-11 - - - -Wall fastening K12 1818 0.3 0.2 0.15 0.1Ceiling fastening K12 1818 0.35 0.2 0.15 0.1
G-GRM 75/50
Dimensions
Load
G-shaped mesh cable tray made of spot-welded steel wire with different side heights and widths. Direct wall or ceiling mounting possible. Load capacity details regarding the different mountingmethods are available upon request.Magnetic shield insulation 15 dB.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
Hook rail for G mesh cable tray
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised
55 25 15TypeG-GRM-R75 FS
Lengthmm
Widthmm
Side heightmm Item No.
6005607
Pack.pcs25
Weightkg/100 pcs.2.400
55 25 15G-GRM-R75VA4301 600563725 2.400
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
G mesh cable tray Magic
49
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
G mesh cable tray Magic, side height 125 mm
G-shaped mesh cable tray made of spot-welded steel wire with different side heights and widths. Direct wall or ceiling mounting possible. Load capacity details regarding the different mountingmethods are available upon request.Magnetic shield insulation 15 dB.
Dimensions
3000 75 125 40 96 3.9TypeG-GRM 125 75 G
Lengthmm
Dim.Bmm
Dim.Hmm
Dim.Cmm
Dim.Amm
WireØmm
Load
Support spacing [m] Load [kN/m] Fastening variant 1 1.5 2 2.5Bracket MWAG 12-11 0.6 0.35 0.3 0.2Wall fastening K12 1818 0.25 0.25 0.2 0.15Ceiling fastening K12 1818 0.3 0.25 0.2 0.15
G-GRM 125/75
125 3.9TypeG-GRM 125 75 G
Side heightmm
WireØmm Item No.
6005541
Pack.m3
Weightkg/100 m108.000
125 3.9G-GRM 125 75 FT 60055263 113.670
125 3.9G-GRM 125 75V2A 60055563 108.000
125 3.9G-GRM 125 75V4A 60055713 108.000
Hook rail for G mesh cable tray
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised
105 25 15TypeG-GRM-R125 FS
Lengthmm
Widthmm
Side heightmm Item No.
6005612
Pack.pcs25
Weightkg/100 pcs.4.600
105 25 15G-GRM-R125VA4301 600564225 4.600
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
G mesh cable tray Magic
50
G mesh cable tray Magic, side height 150 mm
150 3.9TypeG-GRM 150 100 G
Side heightmm
WireØmm Item No.
6005544
Pack.m3
Weightkg/100 m128.000
150 3.9G-GRM 150 100 FT 60055293 130.900
150 3.9G-GRM 150 100V2A 60055593 128.000
150 3.9G-GRM 150 100V4A 60055743 128.000
3000 100 155 70 120 3.9TypeG-GRM 150 100 G
Lengthmm
Dim.Bmm
Dim.Hmm
Dim.Cmm
Dim.Amm
WireØmm
Support spacing [m] Load [kN/m] Fastening variant 1 1.5 2 2.5Bracket MWAG 12-11 0.6 0.5 0.35 0.3Wall fastening K12 1818 0.25 0.2 0.15 0.1Ceiling fastening K12 1818 0.25 0.25 0.15 0.1
G-GRM 150/100
Dimensions
Load
G-shaped mesh cable tray made of spot-welded steel wire with different side heights and widths. Direct wall or ceiling mounting possible. Load capacity details regarding the different mountingmethods are available upon request.Magnetic shield insulation 15 dB.
St Steel V2A Stainless steel, grade 304 V4A Stainless steel, grade 316
G Electrogalvanised FT Hot-dip galvanised
Hook rail for G mesh cable tray
St Steel V2A Stainless steel, grade 304
FS Strip-galvanised
110 25 15TypeG-GRM-R150 FS
Lengthmm
Widthmm
Side heightmm Item No.
6005615
Pack.pcs25
Weightkg/100 pcs.4.800
110 25 15G-GRM-R150VA4301 600564525 4.800
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
G mesh cable tray Magic
51
St Steel V2A Stainless steel, grade 304
GB Stained FT Hot-dip galvanised
C mesh cable tray CGR
C-shaped mesh cable tray made of spot-welded steel wire of side height 50 mm. Dimensions
3000 50 4.5 133000 100 4.5 343000 200 4.5 753000 300 4.5 1163000 400 4.5 157
TypeCGR 50 50 FTCGR 50 100 FTCGR 50 200 FTCGR 50 300 FTCGR 50 400 FT
Lengthmm
Widthmm
WireØmm
Usefulcross-sectioncm²
0.95 0.6 0.350.95 0.6 0.351.1 0.7 0.41.1 0.7 0.41.1 0.7 0.4
TypeCGR 50 50 FTCGR 50 100 FTCGR 50 200 FTCGR 50 300 FTCGR 50 400 FT
1.0 mkN/m
1.5 mkN/m
2.0 mkN/m
Load
Load diagram, C mesh cable tray, type CGR 50Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
50 4.550 4.550 4.550 4.550 4.5
TypeCGR 50 50 FTCGR 50 100 FTCGR 50 200 FTCGR 50 300 FTCGR 50 400 FT
Side heightmm
WireØmm Item No.
60174286017436601744460174526017460
Pack.m33333
Weightkg/100 m128.670136.667173.340204.340240.000
50 4.550 4.550 4.550 4.550 4.5
CGR 50 50 VA4301CGR 50 100VA4301CGR 50 200VA4301CGR 50 300VA4301CGR 50 400VA4301
60162006016235601625160162536016255
33333
124.670131.667169.000195.340222.334
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
C mesh cable tray
52
Barrier strip
Barrier strip for separation of cables of different voltages or functions.
St Steel V2A Stainless steel, grade 304
DD Strip galvanised zinc/aluminium, Double Dip
30 0.75 3000TypeTSG 30 DD
Dim.Hmm
Plate thicknessmm
Dim.Lmm Item No.
6062314
Pack.m3
Weightkg/100 m38.000
30 0.75 3000TSG 30 VA4301 60620523 37.670
Barrier strip connector
Barrier strip connector for screwless connection of the TSG barrier strip in all side heights.
V2A Stainless steel, grade 301
TypeTSGV VA4310
Item No.6067970
Pack.pcs10
Weightkg/100 pcs.0.923
Hold-down clamp for barrier strip fastening
Hold-down clamp for fastening barrier strips in mesh cable trays.
V2A Stainless steel, grade 301
TypeKS GR VA4310
Item No.6062282
Pack.pcs30
Weightkg/100 pcs.0.830
Hold-down clamp for barrier strip fastening
38
724
Including FRS M6 x 20 bolt with flange nut.Clamp for fastening barrier strip in mesh cable trays.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeGKT 38 FT
Item No.6017061
Pack.pcs20
Weightkg/100 pcs.2.400
GKT 38 VA4301 601704520 2.200
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
C mesh cable tray
53
Joint connector
34
28
Including FRS M6 x 20 bolt with flange nut.Screwed version of joint connector for mesh cable trays.Figure: Positioning and quantity of mesh cable tray connectors.50-150 mm = 2 units200-300 mm = 3 units400-450 mm = 4 units500-600 mm = 5 units
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeGSV 34 FT
Item No.6016634
Pack.pcs20
Weightkg/100 pcs.3.000
GSV 34 VA4301 601664220 3.000
45° mounting angle
178
103
Each with two clamps of type KS 23/35.45° installation profile, vertical, for C mesh cable tray and GR-Magic® mesh cable tray with a sideheight of 55 mm.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeMW 45 SL10 FT
Item No.6017320
Pack.pcs20
Weightkg/100 pcs.21.000
MW 45 SL10VA4301 601733920 20.000
90° mounting angle
230
Each with two clamps of type KS 23/35.90° installation profile, vertical, for C mesh cable tray and GR-Magic® mesh cable tray with a sideheight of 55 mm.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeMW 90 SL17 FTMW 90 SL23 FT
Item No.60173476017355
Pack.pcs2020
Weightkg/100 pcs.27.00035.400
MW 90 SL17VA4301MW 90 SL23VA4301
60162786016308
2020
27.00034.700
Hold-down clamp
220
M6
17 23
24.5
35
Including M6 locknut.Clamp for mounting bracket, type MW 45 and MW 90.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeKS 23 35 FT
Item No.6015174
Pack.pcs100
Weightkg/100 pcs.2.015
KS 23 35 VA4301 601652920 2.015
Hold-down clamp
34
22
Including FRS M6 x 20 bolt with flange nut.Clamp for fixing mesh cable trays to wall or support brackets.
St Steel V2A Stainless steel, grade 304
FT Hot-dip galvanised
TypeGKS 34 FT
Item No.6016820
Pack.pcs20
Weightkg/100 pcs.2.000
GKS 34 VA4301 601683920 2.000
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
C mesh cable tray
54
Hook screw
Hook screw for fastening cable tracks on the bracket.
V2A Stainless steel, A2
M6TypeHS M6x13 A2
ThreadItem No.1154990
Pack.pcs100
Weightkg/100 pcs.0.612
Flange nut
Combination nut with washer based on EN 1661.
V2A Stainless steel, A2
6 6 10 A2-70TypeKM M6 A2
Dim.dmm
Dim.hmm
SWmm
Resistanceclass Item No.
6408966
Pack.pcs100
Weightkg/100 pcs.0.315
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
C mesh cable tray
55
St Steel
G Electrogalvanised
Mesh cable tray GR
The grid width is 50 x 100 mm.Mesh cable tray made of spot-welded steel wire of side height 155 mm.Magnetic shield insulation without cover 15 dB, with cover 25 dB.
Dimensions
3000 300 6 4383000 450 6 6633000 500 6 7383000 600 6 888
TypeGR 155 300 GGR 155 450 GGR 155 500 GGR 155 600 G
Lengthmm
Dim.Bmm
WireØmm
Usefulcross-sectioncm²
3 1.8 13 1.8 13 1.8 11.56 1.5 1
TypeGR 155 300 GGR 155 450 GGR 155 500 GGR 155 600 G
1.5 mkN/m
2.0 mkN/m
3.0 mkN/m
Load
Permitted cable tray/ladder load in kN/m without man load
Support width in m
Rail bend in mm at permitted kN/m
Load scheme during testing
Load curve with cable tray/ladder width in mm
Strut bend curve according to support width
3000 63000 63000 63000 6
TypeGR 155 300 GGR 155 450 GGR 155 500 GGR 155 600 G
Lengthmm
WireØmm Item No.
6003681600368460036856003687
Pack.m3333
Weightkg/100 m426.340524.670557.340622.340
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 155
56
Barrier strip
Barrier strip for separation of cables of different voltages or functions.
St Steel
FS Strip-galvanised
135 0.75 3000TypeTSG 135 FS
Dim.Hmm
Plate thicknessmm
Dim.Lmm Item No.
6062132
Pack.m3
Weightkg/100 m100.000
Hold-down clamp
38
724
Including FRS M6 x 20 bolt with flange nut.Clamp for fastening barrier strip in mesh cable trays.
St Steel
G Electrogalvanised
TypeGKT 38 G
Item No.6017037
Pack.pcs20
Weightkg/100 pcs.2.300
Joint connector
Including FRS M6 x 20 bolt with combination nut.Screwed version of joint connector for mesh cable trays with 6.0 mm wire thickness.
St Steel
G Electrogalvanised
TypeGSV 6.0 G
Item No.6016589
Pack.pcs20
Weightkg/100 pcs.5.000
End cap
15End cap to cover cut wire ends of mesh cable trays.
PVC Polyvinylchloride
Pure orangeTypeGR KS 6.0 OR
ColourItem No.6003758
Pack.pcs500
Weightkg/100 pcs.0.036
Hold-down clip
Hold-down clip for the screwless mounting of mesh cable trays onto MS profile rails.
V2A Stainless steel, grade 301
19 For wire Ø 6.0 mmTypeBC GR 6.0 VA
Dim.bmm Version Item No.
6016668
Pack.pcs20
Weightkg/100 pcs.1.760
04 K
TS B
rosc
hüre
Gitt
errin
nen
2017
/ en
/ 03
/08/
2017
(LLE
xpor
t_04
607)
/ 03
/08/
2017
Side height 155
57
OBO Bettermann GmbH & Co. KG PO Box 112058694 MendenGERMANY
Customer Service GermanyTel.: +49 (0)2373 89-1700Fax: +49 (0)2373 89-1238E-mail: [email protected]
www.obo-bettermann.com
Building Connections
© O
BO
BETT
ER
MA
NN
08/1
7 E
N