MENU Quick start guide VOL+ VOL- VOL+ VOL- - VTech Phones...
2
Quick start guide for model LS6245 Install the telephone base Install the telephone base as shown below. Battery installation and charging Install the battery as shown below. For optimal performance, charge the handset battery for at least 16 hours before use. Pair your first Bluetooth cell phone To pair and connect your first Bluetooth cell phone: Press the MENU softkey on the telephone base. Press / VOL + or VOL - / to highlight Bluetooth, then press the SELECT softkey. Press / VOL + or VOL - / to highlight Setup cell, then press the SELECT softkey. Press the NEXT softkey to set the telephone base in discoverable mode. Turn on the Bluetooth feature of your cell phone and search for or add new devices. Once your cell phone finds VTech LS6245, select it. Enter the telephone base PIN (the default PIN is 0000) into your cell phone. When successfully connected, Device connected to base displays. 1. 2. 3. 4. 5. 6. 7. 8. Use only the power adapter and battery supplied with your VTech telephone. For complete feature instructions, please refer to your user’s manual. 1. 2. Pair your first Bluetooth headset To pair and connect your first Bluetooth headset: Telephone line cord DSL filter (not included) is required if you have DSL high speed Internet service Telephone base power adapter Electrical outlet not controlled by a wall switch Telephone wall jack Telephone base If the battery compartment cover is on the handset, press on the triangle and slide the cover to remove. 1. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color- coded label. 2. Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment. 3. Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place. 4. Charge the handset by placing it in the telephone base. The CHARGE light is on when the handset charges. 5. CHARGE light Setup cell Setup headset Active devices SELECT Page all HS Intercom Bluetooth SELECT Pls set your cell to search for devices NEXT LS6245 discoverable PIN:0000 Pairing complete BASE 2:22pm 12/25 MENU REDIAL Device connected to base Press the MENU softkey on the telephone base. Press / VOL + or VOL - / to highlight Bluetooth, then press the SELECT softkey. Press / VOL + or VOL - / to highlight Setup headset, then press the SELECT softkey. Set your headset to discoverable mode. Press the NEXT softkey on the telephone base to search for your headset. Once the telephone base finds your headset, press the SELECT softkey. Enter the PIN of your headset (the PIN for most Bluetooth devices is 0000), then press the NEXT softkey. The screen displays Headset setup complete. When the base displays Connect headset to base? , press the YES softkey. When successfully connected, Device connected to base displays. 1. 2. 3. 4. 5. 6. 7. 8. 9. Page all HS Intercom Bluetooth SELECT BASE 2:22pm 12/25 MENU REDIAL Pls set headset to discoverable mode NEXT Searching for headset Headset setup complete Connect headset to base? NO YES Device connected to base SELECT HEADSET Mary’s Headset SELECT ENTER PIN ---- NEXT Setup cell Setup headset Active devices SELECT The pairing process may take up to one minute. If the pairing process fails, try again. The pairing process may take up to one minute. If the pairing process fails, try again.
Transcript of MENU Quick start guide VOL+ VOL- VOL+ VOL- - VTech Phones...
Quick start guidefor model LS6245
Install the telephone baseInstall the telephone base as shown below.
Battery installation and chargingInstall the battery as shown below. For optimal performance, charge the handset battery for at least 16 hours before use.
Pair your first Bluetooth cell phoneTo pair and connect your first Bluetooth cell phone:
Press the MENU softkey on the telephone base.
Press /VOL+ or VOL-/ to highlight Bluetooth, then press the SELECT softkey.
Press /VOL+ or VOL-/ to highlight Setup cell, then press the SELECT softkey.
Press the NEXT softkey to set the telephone base in discoverable mode.
Turn on the Bluetooth feature of your cell phone and search for or add new devices.
Once your cell phone finds VTech LS6245, select it.
Enter the telephone base PIN (the default PIN is 0000) into your cell phone.
When successfully connected, Device connected to base displays.
1.
2.
3.
4.
5.
6.
7.
8.
Use only the power adapter and battery supplied with your VTech telephone.For complete feature instructions, please refer to your user’s manual.
1.
2.
Pair your first Bluetooth headsetTo pair and connect your first Bluetooth headset:
Telephone line cord
DSL filter (not included) is required if you have DSL high speed Internet service
Telephone base power adapter
Electrical outlet not controlled by a wall switch
Telephone wall jack
Telephone base
If the battery compartment cover is on the handset, press on the triangle and slide the cover to remove.
1. Plug the battery connector securely into the socket inside the handset battery compartment, matching the color-coded label.
2.
Place the battery with the label THIS SIDE UP facing up and the wires inside the battery compartment.
3. Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks into place.
4.
Charge the handset by placing it in the telephone base. The CHARGE light is on when the handset charges.
5.
CHARGE light
Setup cellSetup headsetActive devices
Select
Page all HSIntercomBluetooth
Select
Pls set yourcell to search for devices
next
lS6245 discoverable PIn:0000
Pairing complete
BASe
2:22pm 12/25menuredIAl
device connected to base
Press the MENU softkey on the telephone base.
Press /VOL+ or VOL-/ to highlight Bluetooth, then press the SELECT softkey.
Press /VOL+ or VOL-/ to highlight Setup headset, then press the SELECT softkey.
Set your headset to discoverable mode.
Press the NEXT softkey on the telephone base to search for your headset.
Once the telephone base finds your headset, press the SELECT softkey.
Enter the PIN of your headset (the PIN for most Bluetooth devices is 0000), then press the NEXT softkey. The screen displays Headset setup complete.
When the base displays Connect headset to base?, press the YES softkey.
When successfully connected, Device connected to base displays.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Page all HSIntercomBluetooth
Select
BASe
2:22pm 12/25menuredIAl
Pls set headset to discoverable mode
next
Searching for headset
Headset setup complete
connect headset to base?
noyeS
device connected to base
Select HeAdSetmary’s Headset
Select
enter PIn
----
next
Setup cellSetup headsetActive devices
Select
The pairing process may take up to one minute. If the pairing process fails, try again.
The pairing process may take up to one minute. If the pairing process fails, try again.
96-007147-020-100
More about BluetoothYou can make and receive calls using the home and cell lines. The home line is your conventional telephone land line. The cell line is the communications service provided through your Bluetooth enabled cell phone.Before using your Bluetooth device(s) with the telephone base, make sure that:
Your cell phone and/or headset devices are not connected to any other Bluetooth device(s) and the Bluetooth wireless function is on.
Your device is connected to the telephone base and is on the active devices list.
If you experience difficulty using your Bluetooth cell phone:
Make sure that your Bluetooth cell phone is working properly. See your user’s manual of your Bluetooth device for more information.
Delete VTech LS6245 on your cell phone, then delete your cell phone on the paired devices list.
Repeat the pairing process in Pair your first Bluetooth cell phone in this quick start guide.
•
•
•
•
•
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use of such marks by VTech Holdings Limited is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners.
Copyright © 2009 for VTECH TELECOMMUNICATIONS LTD.
Make, answer and end a callTo make a home call:
Press /HOME/FLASH or on the handset and then enter the telephone number.-OR-Press /HOME on the telephone base and then enter the telephone number.
To predial a home call:Dial the number and then press /HOME/FLASH or
on the handset.-OR-Dial the number and then press /HOME on the telephone base.
To answer a home call:Press /HOME/FLASH or on the handset.-OR-Press /HOME on the telephone base.-OR-Press the call button on your headset if you have a Bluetooth headset connected.
To end a home call:Press OFF/CLEAR or put the handset in the telephone base.-OR-Press /HOME on the telephone base.-OR-Press the call button on your headset.
To make a cell call:Press /CELL on the handset or telephone base, then enter the telephone number.Press the DIAL softkey.
To predial a cell call:Enter the telephone number, then press /CELL on the handset or telephone base.
To answer a cell call:Press /CELL on the handset or telephone base.
To end a cell call:Press /CELL on the handset or telephone base.
•
•
•
•
1.
2.
•
•
•
Important notesAuto keylock: To prevent accidental key presses, the handset keys automatically lock after 10 seconds without presses. Press the UNLOCK softkey to unlock the keypad.
Dialing 911: You must unlock the keypad before you can dial 911 or any other number on the handset.
Turn the answering system on or offThe answering system must be turned on to answer and record messages.
To turn on or off with the telephone base:Press the MENU softkey.
Press /VOL+ or VOL-/ to highlight Ans. system, then press the SELECT softkey.
Press /VOL+ or VOL-/ to highlight Ans sys setup, then press the SELECT softkey.
Press /VOL+ or VOL-/ to highlight Answer ON/OFF, then press the SELECT softkey.
Press /VOL+ or VOL-/ to choose On or Off, then press the SET softkey.
To turn on or off with a handset:
Press the MENU softkey.
Press /VOL+/ or CID/VOL-/ to highlight ANS. SYSTEM, then press the SELECT softkey.
Press /VOL+/ or CID/VOL-/ to highlight Ans sys setup, then press the SELECT softkey.
Press /VOL+/ or CID/VOL-/ to highlight Answer ON/OFF, then press the SELECT softkey.
Press /VOL+/ or CID/VOL-/ to choose On or Off, then press the SET softkey to confirm.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
Message playbackTo play messages with the telephone base:
Press to listen to messages.
Options during playback:Press /VOL+ or VOL-/ to adjust the
speaker volume.Press to skip to the next message. Press CANCEL/ to repeat the message currently
playing. Press CANCEL/ twice to listen to the previous message.
Press FLASH/X to delete the current message. The system advances to the next message.
Press to stop.
To play messages with a handset:
Press the MENU softkey.
Press /VOL+/ or CID/VOL-/ to highlight ANS. SYSTEM, then press the SELECT softkey.
Press /VOL+/ or CID/VOL-/ to highlight Play msgs, then press the SELECT softkey.
Options during playback: Press /VOL+/ or CID/VOL-/ to adjust the
speaker volume. Press 6 to skip to the next message. Press 4 to repeat the message currently playing.
Press 4 twice to listen to the previous message. Press 3 to delete the current message. The
system advances to the next message. Press 5 to stop. Press the BACK softkey to exit and return to the
previous menu.
•
•
••
•
•
1.
2.
3.
•
••
•
••
IMPORTANT!If the LS6245 system is not working properly:
Refer to the Troubleshooting section of the user’s manual.Visit our website at www.vtechcanada.com or call 1 (800) 267-7377.
•
•
HAndSet xon
Press unlocKto use keys
unlocK
