MECHANICAL 2011-2015 wod chennai

2
MARIMUTHU ALIAS MATHAVAN S 967, S.T.R.Nagar, K.T.C. Nagar, Tirunelveli Contact No:-+91 9442569806 E-mail:-[email protected] CAREER OBJECTIVE To have a growth oriented and challenging career, where I can contribute my knowledge and skills to the organization and enhance my experience through continuous learning and teamwork. BASIC ACADEMIC CREDENTIALS Course Institute Board/University Year Percentage/ Grade B.E.(Mechanical) University VOC College of Engineering, Tuticorin Anna University Chennai 2011 – 2015 7.79/10 HSC St. Xavier’s Hr. Sec. School, Tirunelveli State Board 2011 85.16 SSLC St. Xavier’s Hr. Sec. School, Tirunelveli State Board 2009 91.8 ACADEMIC PROJECT PROFILE v Major Project DURATION: (Jan-April 2015) MECHANICAL BEHAVIOUR OF Al ALLOY REINFORCED WITH Al 2 O 3 / RICE HUSK ASH PARTICLES SYNTHESIZEDBY STIRCASTING Aluminium Matrix Composites was fabricated by reinforcing alumina and rice husk ash particles to the matrix of AA 6061 and its mechanical properties such as Hardness, Ultimate Tensile Strength and flexural strength increases while its density decreases with the addition of reinforcements. v Mini Project DURATION: (Jan- April 2013) DESIGN & FABRICATION PROJECT ONBRIMMED DIFFUSER IN WIND TURBINE In a conventional wind turbine prototype, a broad-ring flanged diffuser shroud is designed and fixed at the exit periphery. The flanged diffuser generates a low-pressure region at the exit by vortex formation which draws more air mass flow to the wind turbine inside the diffuser shroud, thereby increasing the efficiency of the wind turbine. INDUSTRIAL TRAINING · TTPS, Tuticorin & NTECL, Chennai (Dec 2013& Dec 14) Learnt the working of thermal power plant and the various components involved in the efficient functioning of the plant. Observed the practical operation of storage unit, conveyor system, boiler cooling tower, condenser unit, turbines, fans and electrostatic precipitators. · Ciranjeevi Wind Energy Limited, Trichy (Dec 2014) Learnt about the functioning of the gear box, yawing system and pitch control system in the nacelle. Acquired an overview of the various surface cleaning methods and painting techniques used in non- pressure parts. · The India CementsLimited, Tirunelveli (Dec 2014) Obtained a general idea about the processes involved in cement making. Observed the working of crusher, vertical rolling mill, kiln, cement grinder and packer.

Transcript of MECHANICAL 2011-2015 wod chennai

Page 1: MECHANICAL 2011-2015 wod chennai

MARIMUTHU ALIAS MATHAVAN S 967, S.T.R.Nagar, K.T.C. Nagar, Tirunelveli

Contact No:-+91 9442569806 E-mail:[email protected]

CAREER OBJECTIVE To have a growth oriented and challenging career, where I can contribute my knowledge and skills to the organization and enhance my experience through continuous learning and teamwork. BASIC ACADEMIC CREDENTIALS

Course Institute Board/University Year Percentage/

Grade

B.E.(Mechanical) University VOC College of Engineering, Tuticorin

Anna University Chennai

2011 – 2015 7.79/10

HSC St. Xavier’s Hr. Sec. School, Tirunelveli

State Board 2011 85.16

SSLC St. Xavier’s Hr. Sec. School, Tirunelveli State Board 2009 91.8

ACADEMIC PROJECT PROFILE

v Major Project DURATION: (Jan-April 2015)

MECHANICAL BEHAVIOUR OF Al ALLOY REINFORCED WITH Al2O3 / RICE HUSK ASH PARTICLES SYNTHESIZEDBY STIRCASTING Aluminium Matrix Composites was fabricated by reinforcing alumina and rice husk ash particles to the matrix of AA 6061 and its mechanical properties such as Hardness, Ultimate Tensile Strength and flexural strength increases while its density decreases with the addition of reinforcements.

v Mini Project DURATION: (Jan- April 2013)

DESIGN & FABRICATION PROJECT ONBRIMMED DIFFUSER IN WIND TURBINE In a conventional wind turbine prototype, a broad-ring flanged diffuser shroud is designed and fixed at the exit periphery. The flanged diffuser generates a low-pressure region at the exit by vortex formation which draws more air mass flow to the wind turbine inside the diffuser shroud, thereby increasing the efficiency of the wind turbine.

INDUSTRIAL TRAINING

· TTPS, Tuticorin & NTECL, Chennai (Dec 2013& Dec 14) Learnt the working of thermal power plant and the various components involved in the efficient functioning of the plant. Observed the practical operation of storage unit, conveyor system, boiler cooling tower, condenser unit, turbines, fans and electrostatic precipitators.

· Ciranjeevi Wind Energy Limited, Trichy (Dec 2014) Learnt about the functioning of the gear box, yawing system and pitch control system in the nacelle. Acquired an overview of the various surface cleaning methods and painting techniques used in non-pressure parts.

· The India CementsLimited, Tirunelveli (Dec 2014) Obtained a general idea about the processes involved in cement making. Observed the working of crusher, vertical rolling mill, kiln, cement grinder and packer.

Page 2: MECHANICAL 2011-2015 wod chennai

· Tamilnadu State Transport Corporation(TNSTC), Tirunelveli (Dec 2012)

Explored and learnt about the various parts of an automobile and its working. Observed the working and fault rectification of various components of IC Engine, Differential, Gear Box& Clutch.

INDUSTRAIL VISIT

Ø BHEL, Trichy Ø Five Star Industries, Trichy Ø MYPOL, Mysore

SKILL SET

Technical Skills:

v Core Software: AUTOCAD, CREO, CATIA, ANSYS, SOLID EDGE v Language:C++ , C v Operating System : Windows

Soft Skills:

v Ability to work in a team v Inter personal skill v Good problem solving skill

ACADEMIC ACHIEVEMENTS AND CO-CURRICULAR ACTIVITIES

· Attended “International workshop on Stress asssisted Environmental Damage in Structural Materials” at IIT, Madras.

· Completed training on “Skill Development Programme on Programming and Operation of CNC Lathe” conducted by MSME Development Institute, Tuticorin.

· Attended Nissan “CVT and Modern Trends workshop” conducted by Department of Automobile Engineering MIT Chennai at AUTOMEET’14

· Attended Workshop on “IC Engines Technologies” conducted by Experts Hub and Automobile Club of IIT-Delhi at IJCE-Tuticorin on Aug 2013.

· Presented a paper on “Globel Warming” at the State Level Symposium EMPHYC’12 conducted by Department of Science & Humanities at SCAD College of Engineering and Technology in April 12.

· Certified as “DME” by CCI Centre, Tirunelveli for completing courses on AUTOCAD, PRO E. · Certified as “Foundation Course on Mechanical CAD- CATIA V6” by Penta CAD, Tirunelveli.

EXTRA CURRICULAR ACTIVITIES

Club activities: · Member, National Service Scheme (NSS) · Active Member, SAE Club

Position Responsibility:

· Member,Organizing Committee of RAA’2014 (Recent Advances in Automotive) · Member, Organizing Committee of PEMETRIX’14 (National Level TechnicalSymposium )

PERSONAL DETAILS

v Father’s Name :- Shunmugam C v Date of Birth :- 10 August 1993 v Languages Known :- English & Tamil v Nationality :- Indian v Interest & Hobbies :- Reading books, Net surfing and Playing games

DECLARATION

I do hereby declare that the above information is true to the best of my knowledge.

Place: Chennai MARIMUTHU ALIAS MATHAVANS