MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process...
-
Upload
peter-bruce -
Category
Documents
-
view
242 -
download
7
Transcript of MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process...
![Page 1: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/1.jpg)
MECH152-L20-1 (1.0) - 1
Extrusion
![Page 2: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/2.jpg)
MECH152-L20-1 (1.0) - 2
Extrusion
A compression forming process in which the work metal is forced to flow through a die opening to produce a desired cross-sectional shape.
Pros:– variety of sections possible (hot extrusion)– grain structure and strength enhancement (cold)– close tolerance (cold)– no material wastage.
![Page 3: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/3.jpg)
MECH152-L20-1 (1.0) - 3
Types of Extrusion
Direct ExtrusionThe ram forces the work billet metal to move
forward to pass through the die opening.
Indirect ExtrusionThe die is mounted to the ram rather than at the
opposite end of the extruder container housing.
![Page 4: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/4.jpg)
MECH152-L20-1 (1.0) - 4
Direct Extrusion
Friction increases the extrusion force.
Hollow section is formed using a mandrel.
![Page 5: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/5.jpg)
MECH152-L20-1 (1.0) - 5
Indirect ExtrusionMetal is forced to flow through the die in an opposite direction to the ram’s motion.
Lower extrusion force as the work billet metal is not moving relative to the container wall.
![Page 6: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/6.jpg)
MECH152-L20-1 (1.0) - 6
Extrusion ProcessesHot extrusion
Keeping the processing temperature to above the re-crystalline temperature. Reducing the ram force, increasing the ram speed, and reduction of grain flow characteristics. Controlling the cooling is a problem. Glass may be used as a lubricant.
Cold extrusionOften used to produce discrete parts. Increase strength due to strain hardening, close tolerances, improved surface finish, absence of oxide layer and high production rates.
![Page 7: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/7.jpg)
MECH152-L20-1 (1.0) - 7
Extrusion Analysis
Taking into account friction,
where a =0.8 and b =1.2 to 1.5.
Extrusion ratio,f
ox A
Ar
Assuming all sections are circular, ideal deformation, no friction,no redundant work:
xrlnRam pressure
xf rYp ln
)ln( xf rbaYp
![Page 8: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/8.jpg)
MECH152-L20-1 (1.0) - 8
Extrusion AnalysisFor direct extrusion, additional pressure, pf, required by the
extruder to overcome the wall friction is related as follows:
(1) [equilibrium equation]
For the worst case that the friction shear stress at the wall equals to the shear yield strength of the work metal:
(2)
Subs. (2) into (1), the additional pressure:
The total ram pressure:
The power required:
LDpDp
ocof
4
2
fsc YYp
off D
LYp
2
oxf D
LYp
2
FvP
![Page 9: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/9.jpg)
MECH152-L20-1 (1.0) - 9
Ram Force
Variation of Ram Force with ram stroke and die angle.
![Page 10: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/10.jpg)
MECH152-L20-1 (1.0) - 10
Extrusion Dies For the case of non-circular extruded section, a shape factor
has to be introduced:
where Kx = shape factor
Cx = perimeter of the non-circular extruded section
Co = perimeter of a circle that has the same cross-sectional area as the extruded
section.
For direct extrusion, the extrusion force
25.2
02.098.0
c
xx C
CK
oxfx D
LYKp
2
![Page 11: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/11.jpg)
MECH152-L20-1 (1.0) - 11
Impact Extrusion
Forward backward
combination
![Page 12: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/12.jpg)
MECH152-L20-1 (1.0) - 12
Impact Extrusion
Impact extrusion is performed at higher speeds and shorter strokes than conventional extrusion.
It is for making discrete parts.
For making thin wall-thickness items by permitting large deformation at high speed.
![Page 13: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/13.jpg)
MECH152-L20-1 (1.0) - 13
Hydrostatic Extrusion
Using hydrostatic system to reduce the friction and lower the power requirement.
Sealing is the major problem.
![Page 14: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/14.jpg)
MECH152-L20-1 (1.0) - 14
Extrusion Defects
a) Centre-burst: internal crack due to excessive tensile stress at the centre possibly because of high die angle, low extrusion ratio.
b) Piping: sink hole at the end of billet under direct extrusion.
c) Surface cracking: High part temperature due to low extrusion speed and high strain rates.
![Page 15: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/15.jpg)
MECH152-L20-1 (1.0) - 15
Wire and Bar Drawing
Reducing the cross section of a bar, rod or wire by pulling it through a die.
Bar drawing is generally in a batch mode while the wire drawing is in general in a continuous mode.
![Page 16: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/16.jpg)
MECH152-L20-1 (1.0) - 16
Mechanics of DrawingArea reduction in drawing ; Draft
No friction and true strain
The ideal stress
Taking into account friction and die angle,
where , ,
The drawing force
o
fo
A
AAr
fo DDd
rA
A
f
o
1
1lnln
f
off A
AYY ln
f
ofd A
AY ln
tan1
cL
D12.088.0
2fo DD
D
sin2fo
c
DDL
f
offdf A
AYAAF ln
tan1
![Page 17: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/17.jpg)
MECH152-L20-1 (1.0) - 17
Maximum Reduction Assume perfectly plastic material (n=0), no friction, no
redundant work,
Then
The maximum possible area ratio
The maximum possible reduction
Yr
YA
AY
A
AY
f
o
f
ofd
1
1lnlnln
erAA
rAA
fo
fo
11
111lnln
0.1max
7183.2eAA fo
632.01max eer
![Page 18: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/18.jpg)
MECH152-L20-1 (1.0) - 18
Drawing EquipmentGood dimensional control
Good surface finish
Improved mechanical properties
economic for mass production
![Page 19: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/19.jpg)
MECH152-L20-1 (1.0) - 19
Draw Dies
Approach angle about 6 to 20Back relief angle about 30
![Page 20: MECH152-L20-1 (1.0) - 1 Extrusion. MECH152-L20-1 (1.0) - 2 Extrusion A compression forming process in which the work metal is forced to flow through a.](https://reader035.fdocuments.us/reader035/viewer/2022062423/56649e185503460f94b04fc2/html5/thumbnails/20.jpg)
MECH152-L20-1 (1.0) - 20
Tube Drawing
No mandrel
Fixed mandrel
Floating mandrel