Mds Cual10ni5fe4 English
14
Industrial CuAl10Ni5F e4 C63000 Page Alloy Designation EN CuAl10Ni5Fe4 DIN CEN/TS 13388 CW307G 2.0966 UNS C63000 ING. SOLIS MORENO High Performance Alloys We have developed a wide range of high performance alloys with excellent properties regarding conductivity, strength, corrosion behaviour, bendability and relaxation properties. KME alloys are the first choice materials for high-end applications and products. Chemical Composition Weight percentage Cu Remainder % Al 9.0 .. 10.0 % Ni 4.5 .. 5.5 % Fe 3.0 .. 4.0 % This alloy is in accordance with RoHS 2002/96/CE for electric & electronic equip- ments and 2002/53/CE for automotive industry. Characteristics CuAl10Fe4Ni5 combines high strength, high cavitation -and erosion- resistance. Good resistance against wear and good fatigue behaviour make is a preferred alloy for high static and dynamic stress. Corrosion resistance, even in hot seawater is excellent. Due to the excellent welding properties it is a used for constructions of casted and wrought parts. Main applications are shipbuilding, food- and chemical industry, taps and valves for aggressive waters. Main Applications Industrial Valve Seats, Plunger Tips, Condenser Tube for Power Stations and Desalting Units, Shafting, Pump Parts, Cams, Gears, Valve Guides, Aircraft Parts, Pump Shafts, Structural Members, Corrosion Resistant Articles, Hydraulic Bushings for Earth Moving Equipment, Valve Balls, Bushings, Bearings, Heat Exchanger Flanges, Heat Exchanger Headers, Tanks, Welded Piping Systems, Balls Marine Nuts, Ship Propellers, Pump Parts, Bolts, Propellers Plumbing Faucets Physical Properties Typical values in annealed temper at 20 °C Density 7.58 g/cm³ Thermal expansion coefficient -100 .. 0 °C 20 .. 300 °C 15.5 16.3 10 -6 /K 10 -6 /K Specific heat capacity 0.42 J/ (g·K) Thermal conductivity 51 W/(m·K)
-
Upload
katery-yusleidys -
Category
Documents
-
view
236 -
download
4
description
xjjxnjxjx
Transcript of Mds Cual10ni5fe4 English
Folie 1
Industrial RolledING. SOLIS MORENO
Alloy DesignationENCuAl10Ni5Fe4DIN CEN/TS 13388CW307G 2.0966UNSC63000High Performance Alloys
We have developed a wide range of high performance alloys with excellent properties regarding conductivity, strength, corrosion behaviour, bendability and relaxation properties. KME alloys are the first choice materials for high-end applications and products.
CuAl10Ni5Fe4C63000
Page 1Chemical CompositionWeight percentage
CuRemainder%
Al9.0 .. 10.0%
Ni4.5 .. 5.5%
Fe3.0 .. 4.0%
This alloy is in accordance with RoHS 2002/96/CE for electric & electronic equip- ments and 2002/53/CE for automotive industry.
CharacteristicsCuAl10Fe4Ni5 combines high strength, high cavitation -and erosion- resistance. Good resistance against wear and good fatigue behaviour make is a preferred alloy for high static and dynamic stress. Corrosion resistance, even in hot seawater is excellent. Due to the excellent welding properties it is a used for constructions of casted and wrought parts. Main applications are shipbuilding, food- and chemical industry, taps and valves for aggressive waters.
Main ApplicationsIndustrial Valve Seats, Plunger Tips, Condenser Tube for Power Stations and Desalting Units, Shafting, Pump Parts, Cams, Gears, Valve Guides, Aircraft Parts, Pump Shafts, Structural Members, Corrosion Resistant Articles, Hydraulic Bushings for Earth Moving Equipment, Valve Balls, Bushings, Bearings, Heat Exchanger Flanges, Heat Exchanger Headers, Tanks, Welded Piping Systems, BallsMarine Nuts, Ship Propellers, Pump Parts, Bolts, PropellersPlumbing Faucets
Physical PropertiesTypical values in annealed temper at 20 C
Density7.58g/cm
Thermal expansion coefficient-100 .. 0 C20 .. 300 C15.516.310-6/K10-6/K
Specific heat capacity0.42J/(gK)
Thermal conductivity51W/(mK)
Electrical conductivity (1 MS/m = 1 m/( mm)4.6MS/m
Electrical conductivity (IACS)7.9%
Thermal coefficient of electrical resistance (0 .. 100 C)0.110-3/K
Modulus of elasticity ( 1 GPa = 1 kN/mm) cold formedannealed
124GPa GPa
Industrial RolledING. SOLIS MORENO
Mechanical Properties (EN 1652)
TemperTensile StrengthYield StrengthElongationHardness Minimum MinimumRmRp0.2A50mmHV *
MPaMPa%HV
*only for information
Corrosion Resistance*
Resistant to:Very high corrosion resistance due to formation of a fast building stable Al2O3 protective layer.High wear- and cavitation-resistance, in aggressive maritime air as well as sufide dioxide containing industrial atmosphere. Hot and cold seawater.
Practically resistant against stress corrosion cracking
Not resistant to: Strong oxidising acids.
Fabrication Properties*Cold Forming PropertiesPoorHot Forming PropertiesGoodMachinability (Rating 20)Less suitableElectroplating PropertiesHot Tinning PropertiesFairSoft Soldering, BrazingFairResistance WeldingLess suitableGas Shielded Arc WeldingGoodLaser WeldingFairSoft AnnealingStress Relieving Annealing* For more details call our technical service* For more details call our technical service
C63000
ING. SOLIS MORENO
CuAl10Ni5Fe4
Bending PropertiesThickness: 0.5 mm
8
rel. Bending Radius R/T7bending edge transvers to rolling direction bending edge in rolling direction690 Bending543210
Bending test according to EN ISO 7438 is done with 10 mm wide samples. Smaller samples in general as well as lower thickness allow a lower bending radius without cracks. If needed we supply bending optimized temper classes that far exceed standard quality.Please take care when comparing with ASTM E 290 results, there the bend definition direction is contradictory.
Bending Definition
Transverse = good way Parallel = bad way
8
rel. Bending Radius R/T7bending edge transvers to rolling direction bending edge in rolling direction65180 Bending4321
180 Parallel
90 Parallel
90 Transverse
180 Transverse
Industrial Rolled0Minimum Bending Radius CalculationTo find out the minimum possible bending radius take the R/T value from the list.Example: R/T = 0.5 and thickness 0.3 mm Minimum radius = (R/T) x thickness= 0.5 x 0.3 mm = 0.15 mm
Bending Properties*
TemperThickness RangeBending 90Bending 180
Trans- versParallelTrans-versParallel
mmR/TR/TR/TR/T
R360 0.5
R410 0.5
R460 0.5
R520 0.5
R530 0.5
* Measured at sample width 10 mm according to EN 1654 Possible bending radius = (R/T) x thickness
C63000
ING. SOLIS MORENO
Sanitary and Antimicrobial PropertiesCopper has been recognised as a hygienic material since the dawn of civilisation and, in the last two centuries, the anecdotal evidence has been supported by scientific research showing that copper is antimicrobial,i.e. it inhibits the growth of harmful pathogens - bacteria, moulds, algae, fungi and viruses.Due to its high copper content of about 81% CuAl10Ni5Fe4 provides the full antimicrobial properties of copper to inhibit the growth of bacteria, viruses and fungi which arein contact for a short period of time on
Copper surfaces have sanitizing properties and self-sanitizing activity that make it attractive for hygienic and sanitary use e.g. in hospitals, nursing homes and other healthcare facilities or public buildings. The effect has been verified in recent scientific studies on a range of disease-causing organisms including MRSA, Clostridium difficile, E.coli, Listeria monocytogenes, Influenza A (H1N1) and Aspergillus niger .Picture: Copper coin (Irish penny) on an agar plate with cells of E. coli bacteria For more details please contact ourtechnical service
Marc Solioz.University of Bern
copper containing surfaces.
Softening Resistance
200
Vickers Hardness HV180160140120 100806040200
R580S at 300C R580S at 400C R580S at 450C R580S at 500C
After short time heat treatment Vickers Hardness is measured. The diagram shows typical values.
Industrial Rolled010306018030018003600 18000Time [s]
Bend Fatigue (at room temperature)
The fatigue strength gives an indication about the resistance to variations in applied tension. It is measured under symmetrical alternating load. The maximum bending load for 107 load cycles without crack is measured. Dependent on the temper class it is approximately 1/3 of the tensile strength Rm.
C63000ING. SOLIS MORENO
Camber
Rolling direction
LEvenness
Customized TolerancesOur products are produced in accordance with relevant norms EN 1652 / EN 1654. Customer specific tolerances for Thickness, Width, Camber, Transverse Flatness, Evenness, Twist and Coil set can be defined. We will be happy to meet your demands. EN 1652 defines only camber.
L
Coil set
Thickness ToleranceThickness Range [mm]EN 1652350 mm [mm]KMEStandard [mm]KMEPrecision [mm]0.10 .. 0.20 0.018 0.005 0.0040.21 .. 0.30 0.022 0.007 0.0050.31 .. 0.40 0.025 0.015 0.0060.41 .. 0.50 0.030 0.015 0.0080.51 .. 0.60 0.040 0.017 0.0100.61 .. 0.70 0.040 0.020 0.0100.71 .. 0.85 0.040 0.022 0.0120.86 .. 1.30 0.050 0.025 0.0151.31 .. 2.00 0.060 0.030 0.0202.01 .. 3.00 0.070 0.045 0.0253.00 .. 4.00 0.100 0.050 0.0254.00 .. 6.00 0.120 0.060 0.030Twist
Industrial Rolled
Rolling directionLangle
h hTransverse Flatness
RoughnessRa [m]Thickness [mm]0.13 .. 0.180.1 .. 2.00.20 .. 0.300.1 .. 2.00.35 .. 0.460.1 .. 2.0On request> 2.0hLEvenness Tolerance
Thickness Range [mm]Width Rang [mm]7 .. 20e
21 .. 50
51 .. 100
0.10 .. 0.50+0.10+0.20+0.30
0.50 .. 1.00+0.15+0.25+0.35
Width Tolerance Standard / Precision
Thickness Range [mm]Width Range [mm]10 .. 50
51 .. 100
101 .. 200
201 .. 350
351 .. 700
700 .. 1.250
0.10 .. 1.00+0.2 / +0.1+0.3 / +0.2+0.4 / +0.3+0.6 / +0.4+1.0 / +0.5-
0.20 .. 1.00+0.2 / +0.1+0.3 / +0.2+0.4 / +0.3+0.6 / +0.4+1.0 / +0.5+2.0
1.01 .. 2.00+0.3 / +0.2+0.4 / +0.2+0.5 / +0.4+1.0 / +0.6+1.5 / +0.7+2.0
2.01 .. 3.00+0.5 / +0.3+0.6 / +0.3+0.7 / +0.5+1.2 / +0.7+2.0 / +0.9+3.0
3.01 .. 6.00+2.0 / -+2.3 / -+2.5 / -+3.0 / -+4.0 / -+6.0
Industrial RolledC63000ING. SOLIS MORENO
FormatsDimension*
CoilStrip thickness (other thicknesses on request) Strip widthOutside diameter Weight (Standard)Weight (Deep-Drawing Quality) Weight per mm 0.1 .. 6.00 3 .. 1.250 1.400 8.400 8.000 12.0mm mm mmkg kg kg
Traverse wound stripThickness Width WeightDrums: wood, plastic, metal, flangeless 0.2 .. 1.50 8 .. 60.0300 .. 1.500mmmm kg
TECSTRIP_multicoilThickness WidthInner diameter 300 mm for thickness Inner diameter 400 mm for thickness Maximum weightOuter diameter maximum0.18 .. 0.8015 .. 500.15 .. 0.800.41 .. 0.805.0001.600mm mm mm mm kg mm
Sheet 6.35 mmThickness Width Length WeightSheets in standard dimensionse.g. 1,000 x 2,000 mm on stock0.3 .. 6.3550 ..1.250200 .. 6.5002.800 .. 8.000mm mm mm kg
Sheet> 6.35 mmThickness Width Length WeightSheets in standard dimensions e.g. 1,000 x 2,000 mm6.35 .. 9.5050 .. 2.450200 .. 7.500 10.000mm mm mm kg
PlateThickness Width Length Weight9.5 .. 150 4.500 15.000 8.000mm mm mm kg
DiscThickness Diameter Weight0.3 .. 15020 .. 3.100 10.000mm mm kg
* Some combinations might not be possible
Industrial RolledC63000ING. SOLIS MORENO
Surface coatings & Special Treatments *Dimension
Hot-Dip tinned and STOL28M Tin-Silver STOL13 Thermic Sn
Different thickness per side possibleWidth ThicknessTin Layer Thickness 330 1.50.4 .. 20mm mmm
Electroplating
Tin, Silver, Gold,Cu-Flash, Ni-Flash, Selective platingWidth Thickness
Other coatings on request 400 2.5mm mm
Profiled strips STOLMultigaugeWidth Thickness
Other width on request15 .. 900.23 .. 1mm mm
Surface with extra low residual carbon content possible.
Protection with oil or adhesive foil on request
* Further details you find at www.kme.com
Standards for copper and copper alloys
EN 1652Plate, sheet, strip and circles for general purposes
EN 1654Strip for springs and connectors
EN 1758Strip for lead frames
EN 13148Hot-dip tinned strip
EN 13599Copper plate, sheet and strip for electrical purposes
EN 14436Electrolytically tinned strip
Industrial RolledC63000ING. SOLIS MORENO
Contact (alphabetic order per country)
AUSTRIAFRANCESINGAPORE
KME Austria Vertriebsgesellschaft m.b.H Postfach 1281232 WienPhone + 43-1-6 16 79 86-0Fax+ 43-1-6 16 79 [email protected] France S.A.S.11 bis. rue de lHtel de Ville 92411 Courbevoie CedexPhone + 33 1 478 96-868Fax+ 33 1 466 [email protected] Asia Pte. Ltd.51 Lorong 17 Geylang#06-01 Superior Industrial Building Singapore 388571Phone + 65-63 37 86 71Fax+ 65-67 48 22 [email protected]
BELGIUMGERMANYSPAIN
N.V. KME Benelux SA Leuvenbaan 31820 SteenokkerzeelPhone + 32-2-7 20 18 89Fax+ 32-2-7 20 87 [email protected] Germany AG & Co. KG Klosterstrasse 2949023 OsnabrckPhone + 49 541 321-0Fax+ 49 541 [email protected] Spain S.A.Ctra Sabadell Mollet. km5 Sta. Perttua de Mogado 08130 BarcelonaPhone + 34 93 547 7090Fax+ 34 93 547 [email protected]
CHINAGERMANYSWEDEN
KME Metals Shanghai Trading Ltd. Hong Qiao Road 808, Rm A807 20030 ShanghaiPhone + 86 21 644 786 80Fax+ 86 21 644 786 [email protected] Germany AG & Co. KG Frankentalstrasse 552222 StolbergPhone + 49 2402 105-0Fax+ 49 2402 [email protected] Sverige AB Silkesvgen 26SE-33153Phone + 46 370 40900Fax+ 46 370 [email protected]
CZECH REPUBLICHUNGARYSWITZERLAND
KME Czech Republic s.r.o. nm. Stn 31 0527201 KladnoPhone + 42-0312-60 82 50Fax+ 42-0312-60 82 [email protected] Hungaria Sznesfm Kft. Andor u.47-49 VI.em.616-6181119 BudapestPhone +36-(0)1-2 05 97 75Fax+36-(0)1-2 05 97 [email protected] Suisse SA Binzallee 228055 ZrichPhone + 41-43 3 88 20 00Fax+ 41-43 3 88 20 [email protected]
DANMARKITALYUNITED KINGDOM
KME Danmark A/S Nsbyvej 265000 Odense C.Phone + 45-65-91 64 10Fax+ 45-65-91 64 [email protected] Italy S.p.A.Via Corradino dAscanio. 4 20142 MilanPhone + 39 02 893 88-1Fax+ 39 02 893 [email protected] UKSevern House Prescott Drive Warndon Business Park WR4 9NE WorcesterPhone + 44 1905 751800Fax+ 44 1905 [email protected]
FINLANDPOLANDUSA
Metallcenter Finland OY AB Piiskakuja 1FIN-20380Phone + 358 20 741 1720Fax+ 358 20 741 [email protected] Polska Sp. z o.o.ul. Wszystkich witych 11 32-650 KETYPhone + 48 33 841 09 94Fax+ 48 33 845 19 [email protected] America Inc.1000 Jorie Boulevard. Suite 111 60523 Oak Brook. Illinois Phone + 1 630 990-2025Fax+ 1 630 [email protected]
CA65 KME CuAl10Ni5Fe4 20100326Internetwww.kme.com
DisclaimerThis material flyer is giving you general information about our products. We have collected the information with great care, even though KME can take no warranty for the completeness, correctness and for being up-to-date. The statements are in no way to be deemed as an advisory service of our company, but are only descriptive without guaranteeing or granting property-related qualities. The data given cannot replace expert advice or customers own tests. Liability of the statements in the flyer is specifically excluded unless compelling legal liability facts are evident. Technical changes reserved.
