mcr ALPE ENG 2014 2 czesc 1 - Mercor Doors Fire protection systems Mercor Doors, part of ASSA ABLOY...
Transcript of mcr ALPE ENG 2014 2 czesc 1 - Mercor Doors Fire protection systems Mercor Doors, part of ASSA ABLOY...
mcr ALPE
steel fire doors
EMEMEMEMEMEMEMEMERERERERERERERERGEGEGEGEGEGEGEGEGENCNCNCNCNCNCNCNCYYYYYYYYEXEXEXEXEXEXEXEXITITITITITITITITIT
1Fire protection systems
TABLE OF CONTENT
Introduction, general presentation of steel fire and non-fire resistant doors mcr ALPE
I. Steel hinged doors mcr ALPE non-fire resistant
II. Steel hinged doors mcr ALPE fire resistant EI230
III. Steel hinged doors mcr ALPE fire resistant EI260/EI130
IV. Steel hinged doors mcr ALPE fire resistant EI2120/EI160
V. Steel hinged doors mcr ALPE variant: with stainless 3D adjusted hinges
VI. Technical data sheet
Certificates
3
7
21
35
49
63
77
135
3Fire protection systems
Mercor Doors, part of ASSA ABLOY Group, is a
leading manufacturer of security fire resistant
and non-fire resistant doors and fixed screens,
sliding gates and fire curtains in Poland.
Our products are customised and certified according to European standards, and are designed to ensure people’s security, safety and convenience in residential and commercial buildings. ASSA ABLOY Mercor Doors offers products that meet both safety and design requirements.
ASSA ABLOY MERCOR DOORS
PUSH
TO OPEN
4Fire protection systems
STEEL FIRE AND NON-FIRE RESISTANT DOORS mcr ALPE
Standard equipment:
Door leaf made of steel sheet 0.8 mm pre-coated RAL 7035 Door core made of rockwool Corner frame Mortise DIN latch and deadbolt lock Double PVC handle set European cylinder Steel welded hinges Safety pin Rubber gasket Intumescent gasket (in fire doors) Flush bolt in passive leaf in double leaf doors
Ancillary and optional equipment:
Handle sets of aluminum and stainless steel Additional welded-in hinges
Stainless steel hinges Anti-panic locks and push bars (choice of assortment) Electric locks and frame mounted electric strikes Magnetic contacts Door leaf made of 1.25 mm, 1.5 mm, 2 mm sheets Door leaf pre-coated in RAL: 5010, 9002, 9006, 9010, 9016, 9007 Powder coating in any RAL colour Ventilation grills, fire and non-fire resistant Round and rectangular glazings Stainless steel protective kick plates Anti-rain cap and bottom sealing (threshold, automatic drop down seal) for external doors
5Fire protection systems
STEEL FIRE AND NON-FIRE RESISTANT DOORS mcr ALPE
Types of frames
STAINLESS STEEL HANDLES - OPTIONS
PRE - COATED STEEL
CORNER FRAME INTERNAL FRAME EMBRACING FRAME
KLS001
KLS006
KLS002 KLT004
KLG001 KLT001
STANDARD–7035 9002 9016 9010 9006 5010
Please mind: RAL prints presented herewith are only indicative, may not be identical with those on doors
RUBBER GASKET
INTUMESCENT GASKET
CORNER FRAME
DOOR LEAF
RUBBER GASKET
INTUMESCENT GASKET
INTERNAL FRAME
DOOR LEAF
RUBBER GASKET
INTUMESCENT GASKET
EMBRACING FRAME
DOOR LEAF
8Fire protection systems
mcr ALPE, single leaf HINGED DOORS NON-FIRE RESISTANTCORNER DOOR FRAME (STANDARD)
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into two shaped steel sheets of 0.8 mm, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment: • Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike• Electric lock• Ventilation grill• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti-rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation
• Position signalling contact (magnetic contact)
1.2. Door frame.
As standard, the door is equipped with corner frame. The frame is made of profiled and zinc plated steel 1.5 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.Non-standard frame sizes are made of 1.8 mm steel.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m2 K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 32 dB (automatic drop down seal is mandatory)
9Fire protection systems
* non-fire resistant doors do not include intumescent gasket** see datasheet CUT-OUTS IN CONCRETE WALL
STEEL DOORS mcr ALPE, SINGLE LEAF non-fire resistant and EI230CORNER FRAME (STANDARD), WELDED HINGES (STANDARD)
10Fire protection systems
mcr ALPE, double leaf HINGED DOORS NON-FIRE RESISTANTCORNER DOOR FRAME (STANDARD)
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into two shaped steel sheets of 0.8 mm, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges per door leaf, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Flush bolt on passive leaf• Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment:• Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike• Electric lock• Ventilation grill
• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti-rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation
• Position signalling contact (magnetic contact)
1.2. Door frame.
As standard, the door is equipped with corner frame. The frame is made of profiled and zinc plated steel 1.5 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.Non-standard frames sizes are made of 1.8 mm steel.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m² K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 27 dB (automatic threshold seal is mandatory)
11Fire protection systems
* non-fire resistant doors do not include intumescent gasket** see datasheet CUT-OUTS IN CONCRETE WALL
STEEL DOORS mcr ALPE, DOUBLE LEAF non-fire resistant and EI230CORNER FRAME (STANDARD), WELDED HINGES (STANDARD)
12Fire protection systems
mcr ALPE single leaf HINGED DOORS NON-FIRE RESISTANTINTERNAL DOOR FRAME
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into 0.8 metal door leaves sheets, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment: • Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike• Electric lock• Ventilation grill• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti-rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation
• Position signalling contact (magnetic contact)
1.2. Door frame.
The door may be equipped with an INTERNAL type of frame. The frame is made of profiled and zinc plated steel 1.5 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.Non-standard frame sizes are made of 1.8 mm steel.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m2 K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 32 dB (automatic drop down seal is mandatory)
13Fire protection systems
* non-fire resistant doors do not include intumescent gasket
STEEL DOORS mcr ALPE, SINGLE LEAF non-fire resistant and EI230INTERNAL FRAME, WELDED HINGES (STANDARD)
14Fire protection systems
mcr ALPE double leaf HINGED DOORS NON-FIRE RESISTANTINTERNAL DOOR FRAME
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into 0.8 metal door leaves sheets, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment: • Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike• Electric lock• Ventilation grill• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti-rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation
• Position signalling contact (magnetic contact)
1.2. Door frame.
The door may be equipped with an INTERNAL type of frame. The frame is made of profiled and zinc plated steel 1.5 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.Non-standard frame sizes are made of 1.8 mm steel.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m2 K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 27 dB (automatic drop down seal is mandatory)
15Fire protection systems
* non-fire resistant doors do not include intumescent gasket
STEEL DOORS mcr ALPE, DOUBLE LEAF non-fire resistant and EI230INTERNAL FRAME, WELDED HINGES (STANDARD)
16Fire protection systems
mcr ALPE single leaf HINGED DOORS NON-FIRE RESISTANTEMBRACING DOOR FRAME
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into two shaped steel sheets of 0.8 mm, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:
• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment: • Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike • Electric lock • Ventilation grill• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti-rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation
• Position signalling contact (magnetic contact)
1.2. Door frame.
The door may be equipped with an EMBRACING type of frame (wrap–around frame) which overlaps the wall. The frame is made of profiled and zinc plated steel 1.8 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m2 K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 32 dB (automatic drop down seal is mandatory)
17Fire protection systems
* non-fire resistant doors do not include intumescent gasket** see datasheet CUT-OUTS IN CONCRETE WALL
STEEL DOORS mcr ALPE, SINGLE LEAF non-fire resistant and EI230EMBRACING FRAME, WELDED HINGES (STANDARD)
18Fire protection systems
mcr ALPE double leaf HINGED DOORS NON-FIRE RESISTANTEMBRACING DOOR FRAME
1.1. General characteristics.
The production of non-fire resistant hinged doors mcr ALPE is based on a CNC technology of door leaves integration by means of bending and riveting. This method ensures considerable resistance to corrosion as well as a perfect door leaf surface finish. The core of the door leaf is composed of high-density mineral wool glued into two shaped steel sheets of 0.8 mm, with RAL 7035 finish standard. The door leaf thickness is 54 mm, weight 24 kg/m². In standard doors’ range there are two hinges, one of which is spring-wound for automatic door closing. Doors are manufactured tailor-made to customer’s order. For transport and assembling works, the doors are protected by a plastic film which is laid onto door surface just at the end of production process.
The STANDARD door model is equipped with:• Mortise latch and dead bolt lock (DIN)• Handle set made of grey or black PVC • Standard European cylinder • Flush bolt on passive leaf• Anti-burglary pin on hinges’ side• Door closer reinforcement on hinges’ side• Rubber gasket• Temporary installation bar in the bottom part
On customer’s request, the door may be equipped with various accessories and ancillary equipment: • Door handle made of stainless steel or aluminium
• 3D hinges made of stainless steel• Door closer • Anti-panic lock • Electric strike • Electric lock • Ventilation grill• Pre-coated metal sheets: RAL 5010, 9002, 9006, 9010, 9016
• Door leaf sheet thickness range from 0.6 to 1.5 mm
• Powder coating - all RAL colours• Kit for external door: anti–rain cap + automatic threshold seal or threshold
• Square, rectangular or round glazing (vision panel)
• Door viewer• Kick plate made of stainless steel • Installation brackets for on-wall installation• Position signalling contact (magnetic contact)
1.2. Door frame.
The door may be equipped with an EMBRACING-type of frame (wrap–around frame) which overlaps the wall. The frame is made of profiled and zinc plated steel 1.8 mm thick and coated with the same RAL colour as the door leaf. Rubber gasket is included.
For minimum and maximum door dimensions - see p. 135-138 (certificates).
Temperature coefficient Ud = 1.4 W/m2 K(PN-EN 14351-1+A1:2010)
Maximum acoustic insulation Rw = 27 dB (automatic drop down seal is mandatory)